LX5512B ® TM InGaP HBT 2.4 – 2.5 GHz Power Amplifier P RODUCTION D ATA S HEET KEY FEATURES DESCRIPTION For 19dBm OFDM output power (64QAM, 54Mbps), the PA provides a low EVM (Error-Vector Magnitude) of 3%, and consumes 140mA total DC current. The LX5512B is available in a 16pin 3mmx3mm micro-lead package (MLP). The compact footprint, low profile, and excellent thermal capability of LX5512B meets the requirements of high-gain power amplifiers for IEEE 802.11b/g applications. Advanced InGaP HBT 2.4-2.5GHz Operation Single-Polarity 3.3V Supply Low Quiescent Current ICQ ~65mA Power Gain ~ 32 dB at 2.45GHz & Pout=19dBm Total Current ~140mA for Pout=19dBm at 2.45 GHz OFDM EVM ~3 % for 64QAM/ 54Mbps & Pout=19dBm Small Footprint: 3x3mm2 Low Profile: 0.9mm WWW . Microsemi .C OM The LX5512B is a power amplifier optimized for WLAN applications in the 2.4-2.5 GHz frequency range. The PA is implemented as a threestage monolithic microwave integrated circuit (MMIC) with active bias and input/output pre-matching. The device is manufactured with an InGaP/GaAs Heterojunction Bipolar Transistor (HBT) IC process (MOCVD). It operates at a single low voltage supply of 3.3V with 32 dB power gain between 2.4-2.5GHz, at a low quiescent current of 65mA. APPLICATIONS IMPORTANT: For the most current data, consult MICROSEMI’s website: http://www.microsemi.com IEEE 802.11b/g PRODUCT HIGHLIGHT PACKAGE ORDER INFO LQ Plastic MLPQ 16 pin RoHS Compliant / Pb-free LX5512BLQ Note: Available in Tape & Reel. Append the letters “TR” to the part number. (i.e. LX5512BLQ-TR) Copyright © 2004 Rev. 1.0b, 2005-08-18 Microsemi Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 LX5512B This device is classified as ESD Level 0 in accordance with JESD22-A114-B, (HBM) testing. Appropriate ESD procedures should be observed when handling this device. Page 1 LX5512B ® TM InGaP HBT 2.4 – 2.5 GHz Power Amplifier P RODUCTION D ATA S HEET N/C VC1 14 15 16 12 1 N/C RF OUT 11 2 N/C 10 e3 8 7 6 5 VCC THERMAL DATA 4 VB12 9 VB3 DET REF RF OUT Note: Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into, negative out of specified terminal. LQ 13 VC3 RF IN N/C WWW . Microsemi .C OM DC Supply Voltage, RF off......................................................................................................7V Collector Current..............................................................................................................500mA Total Power Dissipation ......................................................................................................... 2W RF Input Power .................................................................................................................. 5dBm o Operation Ambient Temperature ............................................................................ -40 to +85 C o Storage Temperature............................................................................................ -65 to +150 C Package Peak Temp for Solder Reflow (40 Seconds Maximum Exposure)..........260°C(+0, -5) VC2 PACKAGE PIN OUT N/C ABSOLUTE MAXIMUM RATINGS LQ PACKAGE (Bottom View) Plastic MLPQ 16-Pin RoHS / Pb-free 100% Matte Tin Lead Finish THERMAL RESISTANCE-JUNCTION TO CASE, θJC 10°C/W 50°C/W THERMAL RESISTANCE-JUNCTION TO AMBIENT, θJA Junction Temperature Calculation: TJ = TA + (PD x θJA). The θJA numbers are guidelines for the thermal performance of the device/pc-board system. All of the above assume no ambient airflow. FUNCTIONAL PIN DESCRIPTION Name Description RF IN RF input for the power amplifier. This pin is directly connected to base, a 10pF decoupling capacitor may be needed. VB12 Bias current control voltage for the first and second stage. VB3 Bias current control voltage for the third stage. The VB3 pin can be connected with the first and second stage control voltage (VB12) into a single reference voltage (referred to as VREF) through an external resistor bridge. VCC Supply voltage for the bias reference and control circuits. The VCC feed line should be terminated with a 10nF bypass capacitor close to connector pin. This pin can be combined with VC1, VC2 and VC3 pins, resulting in a single supply voltage (referred to as VC). RF OUT RF output for the power amplifier. This pin is DC-decoupled from the transistor collector of the third stage. Power supply for first stage amplifier. The VC1 feed line should be terminated with a 10pF bypass capacitor, followed by a 36 Ohm resistor. This pin can be combined with VC2,VC3 and VCC pins, resulting in a single supply voltage (referred to as VC). VC2 Power supply for second stage amplifier. The VC2 feed line should be terminated with a 18pF bypass capacitor. This pin can be combined with VC1,VC3 and VCC pins, resulting in a single supply voltage (referred to as VC). VC3 Power supply for the third stage amplifier. The VC3 feed line should be terminated with 27 pF and 10 nF bypass capacitors. This pin can be combined with VC1,VC2 and VCC pins, resulting in a single supply voltage (referred to as VC). REF Power detector reference output pin should be terminated with a 100KΩ loading resistor DET Power detector output pin should be terminated with a 100KΩ loading resistor GND The center metal base of the MLP package provides both DC and RF ground as well as heat sink for the power amplifier. Copyright © 2004 Rev. 1.0b, 2005-08-18 Microsemi Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 2 PACKAGE DATA VC1 LX5512B ® TM InGaP HBT 2.4 – 2.5 GHz Power Amplifier P RODUCTION D ATA S HEET Parameter Symbol Frequency Range Power Gain @ POUT = 19dBm EVM @ POUT = 19dBm Total Current @ POUT = 19dBm Quiescent Current Bias Control Reference Current Small-Signal Gain Gain Flatness Gain Variation Over Temperature Input Return Loss Output Return Loss Reverse Isolation Second Harmonic Third Harmonic Total Current @ POUT = 23dBm nd 2 Side Lobe @ 23dBm Ramp-On Time Differential Detector Response f Gp Test Conditions Min 2.4 64QAM / 54Mbps IC_TOTAL ICQ IREF S21 ΔS21 ΔS21 S11 S22 S12 tON LX5512B Typ Max For ICQ = 65mA Over 100MHz 0 to +85°C POUT = 19dBm POUT = 19dBm 11Mbps CCK 11Mbps CCK 10 ~ 90% 19dBm OFDM 2.5 32 3.0 140 65 1.8 32 ±0.25 ±0.25 10 10 45 -40 -40 215 -55 100 1.4 Units GHz dB % mA mA mA dB dB dB dB dB dB dBc dBc mA dBc ns V WWW . Microsemi .C OM ELECTRICAL CHARACTERISTICS Test conditions: VC = 3.3V, VREF = 2.95V, ICQ = 65mA, TA = 25°C Note: All measured data was obtained on a 10mil GETEK evaluation board without heat sink. ELECTRICALS Copyright © 2004 Rev. 1.0b, 2005-08-18 Microsemi Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 3 LX5512B TM ® InGaP HBT 2.4 – 2.5 GHz Power Amplifier P RODUCTION D ATA S HEET A P P L I C A T I O N S C H E M A T I C & BILL OF MATERIALS WWW . Microsemi .C OM Location C1 C2,C3,C9 C4 C5,C8 C6 C7 R1 R2 R3,R4 TL1 TL2 TL3 TL4 TL5 Substrate Recommended BOM Value 1µF (0603) 10nF(0402) 2pF (0402) 10pF (0402) 18pF (0402) 27pF (0402) 75 Ω (0402) 36 Ω (0402) 100 kΩ (0402) 120/10 mil (L/W) 100/8 mil (L/W) ~350/8 mil (L/W) 40/8 mil (L/W) ~500/8 mil (L/W) 10 mil GETEK εr = 3.9, tan δ = 0.01 50Ω Microstrip width: 20 mil EVALUATION BOARD EVALUATION (10 mil GETEK PCB, 0.9”x0.9”, No Heat Sink) Copyright © 2004 Rev. 1.0b, 2005-08-18 Microsemi Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 4 LX5512B ® TM InGaP HBT 2.4 – 2.5 GHz Power Amplifier P RODUCTION D ATA S HEET S-PARAMETER DATA 6 m1 40 30 m2 20 10 m3 dB(S(1,1)) dB(S(1,2)) 0 175 Current 3.3V EVM PA ONLY -10 -20 5 125 4 100 3 75 2 50 1 25 -30 0 -40 0 0 -50 0 1 2 3 4 5 6 ACP 30MHz 2.0 -50 1.5 -52 1.0 -54 0.5 -56 0 8 10 12 14 16 18 20 Current 3.3V 225 200 Current /[mA] Diff DET Voltage 6 10 12 14 16 18 20 22 250 2.5 -48 4 8 CURRENT @ 11MBPS CCK 3.0 2 6 Output Power /[dBm] ACP & DIFF DETECTOR VOLTAGE -44 0 4 EVM and Supply Current with 54Mbps 64QAM VC = 3.3V, VREF = 2.95V, ICQ = 65mA, Frequency = 2.45GHz VC = 3.3V, VREF = 2.95V, ICQ = 65mA -46 2 7 Frequency (GHz) ACP /[dB] 150 Current /[mA] m3 Freq = 2.45GHz m3 = -9.31 EVM PA /[%] dB(S(2,2)) dB(S(2,1)) 50 m2 Freq = 2.50GHz m2 = 31.46 WWW . Microsemi .C OM m1 Freq = 2.40GHz m1 = 32.02 EVM & SUPPLY CURRENT 7 175 150 125 100 75 50 25 22 Output Power /[dBm] ACP (30MHz) & Differential Detector Voltage with 54Mbps 64QAM VC = 3.3V, VREF = 2.95V, ICQ = 65mA, Frequency = 2.45GHz 0 0 2 4 6 8 10 12 14 16 18 20 22 24 Output Power /[dBm] VC = 3.3V, VREF = 2.95V, ICQ = 65mA, Frequency = 2.45GHz 23DBM OUTPUT @ 11MBPS CCK CHARTS VC = 3.3V, VREF = 2.95V, ICQ = 65mA, Frequency = 2.45GHz Copyright © 2004 Rev. 1.0b, 2005-08-18 Microsemi Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 5 LX5512B ® TM InGaP HBT 2.4 – 2.5 GHz Power Amplifier P RODUCTION D ATA S HEET PACKAGE DIMENSIONS WWW . Microsemi .C OM LQ 16-Pin MLPQ 3x3 D b E2 L D2 E or e K A A1 or Pin 1 Indicator A3 Or Dim A A1 A3 b D E e D2 E2 K L L1 MILLIMETERS MIN MAX 0.80 1.00 0 0.05 0.20 REF 0.18 0.30 3.00 BSC 3.00 BSC 0.50 BSC 1.30 1.55 1.30 1.55 0.2 0.35 0.50 0.15 INCHES MIN MAX 0.031 0.039 0 0.002 0.008 REF 0.007 0.012 0.118 BSC 0.118 BSC 0.020 BSC 0.051 0.061 0.051 0.061 0.008 0.012 0.020 0.006 Note: 1. D E2 b L 2. Dimensions do not include mold flash or protrusions; these shall not exceed 0.155mm(.006”) on any side. Lead dimension shall not include solder coverage. Due to multiple qualified assembly sub-contractors either package (with different pin one indicators) may be shipped. Package type will be consistent within the smallest individual container. D2 E L1 e A1 A K MECHANICALS Copyright © 2004 Rev. 1.0b, 2005-08-18 Microsemi Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 6 LX5512B ® TM InGaP HBT 2.4 – 2.5 GHz Power Amplifier P RODUCTION D ATA S HEET WWW . Microsemi .C OM TAPE AND REEL Tape And Reel Specification Ø 1.50mm 4.00mm Top View 1.75mm 3.30mm 5.5 ± 0.05mm 12.00 ± 0.3mm 3.30mm 8.00mm Ø 1.50mm Part Orientation 1.10mm Side View 0.30mm 2.2mm Ø 13mm +1.5 -0.2 10.6mm Ø 330mm ±0.5 Ø 97mm ±1.0 MECHANICALS 13mm +1.5 Copyright © 2004 Rev. 1.0b, 2005-08-18 Microsemi Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 7 LX5512B TM ® InGaP HBT 2.4 – 2.5 GHz Power Amplifier P RODUCTION D ATA S HEET WWW . Microsemi .C OM NOTES NOTES PRODUCTION DATA – Information contained in this document is proprietary to Microsemi and is current as of publication date. This document may not be modified in any way without the express written consent of Microsemi. Product processing does not necessarily include testing of all parameters. Microsemi reserves the right to change the configuration and performance of the product and to discontinue product at any time. Copyright © 2004 Rev. 1.0b, 2005-08-18 Microsemi Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 8