ETC PCI7410

t ! "
Data Manual
December 2002
Connectivity Solutions
SCPS074
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third–party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Mailing Address:
Texas Instruments
Post Office Box 655303
Dallas, Texas 75265
Copyright  2002, Texas Instruments Incorporated
Contents
Section
1
2
3
Title
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.1
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3
Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.4
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.5
Terms and Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.6
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Terminal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Feature/Protocol Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1
Power Supply Sequencing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2
Summary of UltraMediat Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.1
SmartMedia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.2
MultiMediaCard (MMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.3
Secure Digital (SD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4
Memory Stick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.5
Dedicated Socket (Function 1) Interface . . . . . . . . . . . . . . .
3.3
I/O Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4
Clamping Voltages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5
Peripheral Component Interconnect (PCI) Interface . . . . . . . . . . . . . .
3.5.1
1394 PCI Bus Master . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5.2
PCI Bus Lock (LOCK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5.3
Serial EEPROM I2C Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5.4
Loading Subsystem Identification . . . . . . . . . . . . . . . . . . . . .
3.5.4.1
Function 2 Subsystem Identification . . . . . . . .
3.5.4.2
Function 3 Subsystem Identification . . . . . . . .
3.6
PC Card Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.6.1
PC Card Insertion/Removal and Recognition . . . . . . . . . . .
3.6.2
Low Voltage CardBus Card Detection . . . . . . . . . . . . . . . . .
3.6.3
Card Detection in a UltraMedia System . . . . . . . . . . . . . . . .
3.6.4
Query Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.6.5
Power Switch Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.6.6
Zoomed Video Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.6.7
Standardized Zoomed-Video Register Model . . . . . . . . . . .
3.6.8
Internal Ring Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.6.9
Integrated Pullup Resistors for PC Card Interface . . . . . . .
3.6.10
SPKROUT and CAUDPWM Usage . . . . . . . . . . . . . . . . . . .
3.6.11
LED Socket Activity Indicators . . . . . . . . . . . . . . . . . . . . . . . .
Page
1–1
1–1
1–2
1–3
1–4
1–5
1–5
2–1
3–1
3–1
3–2
3–2
3–2
3–2
3–3
3–3
3–3
3–4
3–4
3–4
3–4
3–5
3–6
3–6
3–6
3–7
3–7
3–7
3–7
3–9
3–9
3–10
3–12
3–12
3–12
3–13
3–13
iii
3.6.12
3.6.13
4
iv
CardBus Socket Registers . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCI Firmware Loading Function Programming Model . . . .
3.6.13.1
Data/Address Register . . . . . . . . . . . . . . . . . . .
3.6.13.2
Firmware Loader Control Register . . . . . . . . .
3.7
Serial EEPROM Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.7.1
Serial-Bus Interface Implementation . . . . . . . . . . . . . . . . . . .
3.7.2
Accessing Serial-Bus Devices Through Software . . . . . . .
3.7.3
Serial-Bus Interface Protocol . . . . . . . . . . . . . . . . . . . . . . . . .
3.7.4
Serial-Bus EEPROM Application . . . . . . . . . . . . . . . . . . . . . .
3.8
Programmable Interrupt Subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.8.1
PC Card Functional and Card Status Change Interrupts .
3.8.2
Interrupt Masks and Flags . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.8.3
Using Parallel IRQ Interrupts . . . . . . . . . . . . . . . . . . . . . . . . .
3.8.4
Using Parallel PCI Interrupts . . . . . . . . . . . . . . . . . . . . . . . . .
3.8.5
Using Serialized IRQSER Interrupts . . . . . . . . . . . . . . . . . . .
3.8.6
SMI Support in the PCI7410 Device . . . . . . . . . . . . . . . . . . .
3.9
Power Management Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.9.1
1394 Power Management (Function 1) . . . . . . . . . . . . . . . .
3.9.2
Integrated Low-Dropout Voltage Regulator (LDO-VR) . . . .
3.9.3
Clock Run Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.9.4
CardBus PC Card Power Management . . . . . . . . . . . . . . . .
3.9.5
16-Bit PC Card Power Management . . . . . . . . . . . . . . . . . . .
3.9.6
Suspend Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.9.7
Requirements for Suspend Mode . . . . . . . . . . . . . . . . . . . . .
3.9.8
Ring Indicate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.9.9
PCI Power Management for CardBus (Function 0) . . . . . .
3.9.9.1
Function 2 Power Management . . . . . . . . . . . .
3.9.9.2
Function 3 Power Management . . . . . . . . . . . .
3.9.10
CardBus Bridge Power Management . . . . . . . . . . . . . . . . . .
3.9.11
ACPI Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.9.12
Master List of PME Context Bits and Global Reset-Only
Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.10 IEEE 1394 Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.10.1
PHY Port Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . .
3.10.2
Crystal Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.10.3
Bus Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PC Card Controller Programming Model . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1
PCI Configuration Registers (Functions 0 and 1) . . . . . . . . . . . . . . . . .
4.2
Vendor ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3
Device ID Register Function 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4
Device ID Register Function 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.5
Command Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.6
Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.7
Revision ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–14
3–14
3–15
3–15
3–16
3–16
3–16
3–16
3–18
3–21
3–21
3–22
3–23
3–23
3–24
3–24
3–24
3–25
3–25
3–26
3–26
3–26
3–26
3–27
3–27
3–28
3–29
3–29
3–29
3–30
3–30
3–32
3–32
3–33
3–34
4–1
4–1
4–2
4–3
4–3
4–4
4–5
4–6
4.8
4.9
4.10
4.11
4.12
4.13
4.14
4.15
4.16
4.17
4.18
4.19
4.20
4.21
4.22
4.23
4.24
4.25
4.26
4.27
4.28
4.29
4.30
4.31
4.32
4.33
4.34
4.35
4.36
4.37
4.38
4.39
4.40
4.41
4.42
4.43
4.44
4.45
4.46
4.47
4.48
4.49
4.50
Class Code Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cache Line Size Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Latency Timer Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Header Type Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BIST Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CardBus Socket Registers/ExCA Base Address Register . . . . . . . . .
Capability Pointer Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Secondary Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCI Bus Number Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CardBus Bus Number Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Subordinate Bus Number Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CardBus Latency Timer Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CardBus Memory Base Registers 0, 1 . . . . . . . . . . . . . . . . . . . . . . . . . .
CardBus Memory Limit Registers 0, 1 . . . . . . . . . . . . . . . . . . . . . . . . . .
CardBus I/O Base Registers 0, 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CardBus I/O Limit Registers 0, 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interrupt Line Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interrupt Pin Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bridge Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Subsystem Vendor ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Subsystem ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PC Card 16-Bit I/F Legacy-Mode Base-Address Register . . . . . . . . .
System Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UM_CD Debounce Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General-Purpose Event Status Register . . . . . . . . . . . . . . . . . . . . . . . .
General-Purpose Event Enable Register . . . . . . . . . . . . . . . . . . . . . . .
General-Purpose Input Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General-Purpose Output Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multifunction Routing Status Register . . . . . . . . . . . . . . . . . . . . . . . . . .
Retry Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Card Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Device Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Capability ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Next Item Pointer Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Management Capabilities Register . . . . . . . . . . . . . . . . . . . . . .
Power Management Control/Status Register . . . . . . . . . . . . . . . . . . . .
Power Management Control/Status Bridge Support Extensions
Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-Management Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Bus Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Bus Index Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Bus Slave Address Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4–6
4–6
4–7
4–7
4–7
4–8
4–8
4–9
4–10
4–10
4–10
4–11
4–11
4–12
4–12
4–13
4–13
4–14
4–15
4–16
4–16
4–17
4–18
4–20
4–21
4–22
4–23
4–23
4–24
4–25
4–26
4–27
4–28
4–29
4–30
4–30
4–31
4–32
4–33
4–33
4–34
4–34
4–35
v
5
6
7
vi
4.51 Serial Bus Control/Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ExCA Compatibility Registers (Functions 0 and 1) . . . . . . . . . . . . . . . . . .
5.1
ExCA Identification and Revision Register . . . . . . . . . . . . . . . . . . . . . .
5.2
ExCA Interface Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.3
ExCA Power Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.4
ExCA Interrupt and General Control Register . . . . . . . . . . . . . . . . . . .
5.5
ExCA Card Status-Change Register . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.6
ExCA Card Status-Change Interrupt Configuration Register . . . . . . .
5.7
ExCA Address Window Enable Register . . . . . . . . . . . . . . . . . . . . . . . .
5.8
ExCA I/O Window Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.9
ExCA I/O Windows 0 and 1 Start-Address Low-Byte Registers . . . .
5.10 ExCA I/O Windows 0 and 1 Start-Address High-Byte Registers . . . .
5.11 ExCA I/O Windows 0 and 1 End-Address Low-Byte Registers . . . . .
5.12 ExCA I/O Windows 0 and 1 End-Address High-Byte Registers . . . .
5.13 ExCA Memory Windows 0–4 Start-Address Low-Byte Registers . . .
5.14 ExCA Memory Windows 0–4 Start-Address High-Byte Registers . . .
5.15 ExCA Memory Windows 0–4 End-Address Low-Byte Registers . . . .
5.16 ExCA Memory Windows 0–4 End-Address High-Byte Registers . . .
5.17 ExCA Memory Windows 0–4 Offset-Address Low-Byte Registers . .
5.18 ExCA Memory Windows 0–4 Offset-Address High-Byte Registers .
5.19 ExCA Card Detect and General Control Register . . . . . . . . . . . . . . . .
5.20 ExCA Global Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.21 ExCA I/O Windows 0 and 1 Offset-Address Low-Byte Registers . . .
5.22 ExCA I/O Windows 0 and 1 Offset-Address High-Byte Registers . . .
5.23 ExCA Memory Windows 0–4 Page Registers . . . . . . . . . . . . . . . . . . .
CardBus Socket Registers (Functions 0 and 1) . . . . . . . . . . . . . . . . . . . . . .
6.1
Socket Event Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2
Socket Mask Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3
Socket Present State Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.4
Socket Force Event Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.5
Socket Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.6
Socket Power Management Register . . . . . . . . . . . . . . . . . . . . . . . . . . .
OHCI Controller Programming Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.1
Vendor ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2
Device ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.3
Command Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.4
Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.5
Class Code and Revision ID Register . . . . . . . . . . . . . . . . . . . . . . . . . .
7.6
Latency Timer and Class Cache Line Size Register . . . . . . . . . . . . . .
7.7
Header Type and BIST Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.8
OHCI Base Address Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.9
TI Extension Base Address Register . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.10 CardBus CIS Base Address Register . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.11 CardBus CIS Pointer Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4–36
5–1
5–5
5–6
5–7
5–8
5–9
5–10
5–11
5–12
5–13
5–13
5–14
5–14
5–15
5–16
5–17
5–18
5–19
5–20
5–21
5–22
5–23
5–23
5–24
6–1
6–2
6–3
6–4
6–5
6–7
6–8
7–1
7–2
7–2
7–3
7–4
7–5
7–5
7–6
7–6
7–7
7–8
7–8
8
7.12 Subsystem Identification Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.13 Power Management Capabilities Pointer Register . . . . . . . . . . . . . . .
7.14 Interrupt Line Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.15 Interrupt Pin Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.16 Minimum Grant and Maximum Latency Register . . . . . . . . . . . . . . . . .
7.17 OHCI Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.18 Capability ID and Next Item Pointer Registers . . . . . . . . . . . . . . . . . . .
7.19 Power Management Capabilities Register . . . . . . . . . . . . . . . . . . . . . .
7.20 Power Management Control and Status Register . . . . . . . . . . . . . . . .
7.21 Power Management Extension Registers . . . . . . . . . . . . . . . . . . . . . . .
7.22 PCI PHY Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.23 PCI Miscellaneous Configuration Register . . . . . . . . . . . . . . . . . . . . . .
7.24 Link Enhancement Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.25 Subsystem Access Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OHCI Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.1
OHCI Version Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2
GUID ROM Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.3
Asynchronous Transmit Retries Register . . . . . . . . . . . . . . . . . . . . . . .
8.4
CSR Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.5
CSR Compare Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.6
CSR Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.7
Configuration ROM Header Register . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.8
Bus Identification Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.9
Bus Options Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.10 GUID High Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.11 GUID Low Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.12 Configuration ROM Mapping Register . . . . . . . . . . . . . . . . . . . . . . . . . .
8.13 Posted Write Address Low Register . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.14 Posted Write Address High Register . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.15 Vendor ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.16 Host Controller Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.17 Self-ID Buffer Pointer Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.18 Self-ID Count Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.19 Isochronous Receive Channel Mask High Register . . . . . . . . . . . . . .
8.20 Isochronous Receive Channel Mask Low Register . . . . . . . . . . . . . . .
8.21 Interrupt Event Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.22 Interrupt Mask Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.23 Isochronous Transmit Interrupt Event Register . . . . . . . . . . . . . . . . . .
8.24 Isochronous Transmit Interrupt Mask Register . . . . . . . . . . . . . . . . . . .
8.25 Isochronous Receive Interrupt Event Register . . . . . . . . . . . . . . . . . . .
8.26 Isochronous Receive Interrupt Mask Register . . . . . . . . . . . . . . . . . . .
8.27 Initial Bandwidth Available Register . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.28 Initial Channels Available High Register . . . . . . . . . . . . . . . . . . . . . . . .
8.29 Initial Channels Available Low Register . . . . . . . . . . . . . . . . . . . . . . . . .
7–9
7–9
7–10
7–10
7–11
7–11
7–12
7–13
7–14
7–14
7–15
7–15
7–17
7–18
8–1
8–4
8–5
8–6
8–6
8–7
8–7
8–8
8–8
8–9
8–10
8–10
8–11
8–11
8–12
8–12
8–13
8–14
8–15
8–16
8–17
8–18
8–20
8–22
8–23
8–24
8–25
8–25
8–26
8–26
vii
8.30 Fairness Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.31 Link Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.32 Node Identification Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.33 PHY Layer Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.34 Isochronous Cycle Timer Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.35 Asynchronous Request Filter High Register . . . . . . . . . . . . . . . . . . . . .
8.36 Asynchronous Request Filter Low Register . . . . . . . . . . . . . . . . . . . . .
8.37 Physical Request Filter High Register . . . . . . . . . . . . . . . . . . . . . . . . . .
8.38 Physical Request Filter Low Register . . . . . . . . . . . . . . . . . . . . . . . . . .
8.39 Physical Upper Bound Register (Optional Register) . . . . . . . . . . . . . .
8.40 Asynchronous Context Control Register . . . . . . . . . . . . . . . . . . . . . . . .
8.41 Asynchronous Context Command Pointer Register . . . . . . . . . . . . . .
8.42 Isochronous Transmit Context Control Register . . . . . . . . . . . . . . . . . .
8.43 Isochronous Transmit Context Command Pointer Register . . . . . . . .
8.44 Isochronous Receive Context Control Register . . . . . . . . . . . . . . . . . .
8.45 Isochronous Receive Context Command Pointer Register . . . . . . . .
8.46 Isochronous Receive Context Match Register . . . . . . . . . . . . . . . . . . .
9 TI Extension Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.1
DV and MPEG2 Timestamp Enhancements . . . . . . . . . . . . . . . . . . . . .
9.2
Isochronous Receive Digital Video Enhancements . . . . . . . . . . . . . . .
9.3
Isochronous Receive Digital Video Enhancements Register . . . . . . .
9.4
Link Enhancement Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.5
Timestamp Offset Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 PHY Register Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.1 Base Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.2 Port Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.3 Vendor Identification Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.4 Vendor-Dependent Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.5 Power-Class Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11 PCI Firmware Loading Function Programming Model (Function 3) . . . .
11.1 Vendor ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.2 Device ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.3 Command Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.4 Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.5 Class Code and Revision ID Register . . . . . . . . . . . . . . . . . . . . . . . . . .
11.6 Cache Line Size Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.7 Latency Timer Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.8 Header Type Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.9 BIST Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.10 Base Address Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.11 Subsystem Vendor ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.12 Subsystem ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.13 Capabilities Pointer Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.14 Interrupt Line Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
viii
8–27
8–28
8–29
8–30
8–31
8–32
8–34
8–35
8–37
8–37
8–38
8–39
8–40
8–41
8–41
8–43
8–44
9–1
9–1
9–2
9–2
9–4
9–5
10–1
10–1
10–4
10–5
10–6
10–7
11–1
11–1
11–2
11–2
11–3
11–4
11–4
11–4
11–5
11–5
11–5
11–6
11–6
11–6
11–7
11.15 Interrupt Pin Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11–7
11.16 Minimum Grant Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11–7
11.17 Maximum Latency Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11–7
11.18 Capability ID Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11–8
11.19 Next-Item Pointer Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11–8
11.20 Power-Management Capabilities Register . . . . . . . . . . . . . . . . . . . . . . 11–9
11.21 Power-Management Control/Status Register . . . . . . . . . . . . . . . . . . 11–10
11.22 Power-Management Bridge Support Extension Register . . . . . . . . 11–10
11.23 Power-Management Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . 11–11
11.24 Miscellaneous Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11–11
11.25 Subsystem Access Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11–12
12 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12–1
12.1 Absolute Maximum Ratings Over Operating Temperature Ranges . 12–1
12.2 Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . 12–1
12.3 Electrical Characteristics Over Recommended Operating
Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12–3
12.4 Electrical Characteristics Over Recommended Ranges of
Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12–3
12.4.1
Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12–3
12.4.2
Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12–4
12.4.3
Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12–4
12.5 PCI Clock/Reset Timing Requirements Over Recommended
Ranges of Supply Voltage and Operating Free-Air Temperature . . . 12–4
12.6 Switching Characteristics for PHY Port Interface . . . . . . . . . . . . . . . . . 12–5
12.7 Operating, Timing, and Switching Characteristics of XI . . . . . . . . . . . 12–5
12.8 PCI Timing Requirements Over Recommended Ranges of
Supply Voltage and Operating Free-Air Temperature . . . . . . . . . . . . . 12–5
13 Mechanical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13–1
ix
List of Illustrations
Figure
2–1
2–2
3–1
3–2
3–3
3–4
3–5
3–6
3–7
3–8
3–9
3–10
3–11
3–12
3–13
3–14
3–15
3–16
3–17
3–18
3–19
3–20
3–21
3–22
3–23
5–1
5–2
6–1
12–1
x
Title
PCI7410 GHK-Package Terminal Diagram . . . . . . . . . . . . . . . . . . . . . . . . .
PCI7410 PDV-Package Terminal Diagram . . . . . . . . . . . . . . . . . . . . . . . . .
PCI7410 System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-State Bidirectional Buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial ROM Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Example Query Terminal Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Zoomed Video Implementation Using the PCI7410 Device . . . . . . . . . . .
Zoomed Video Switching Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPKROUT Connection to Speaker Driver . . . . . . . . . . . . . . . . . . . . . . . . . .
Two Sample LED Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial-Bus Start/Stop Conditions and Bit Transfers . . . . . . . . . . . . . . . . . .
Serial-Bus Protocol Acknowledge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial-Bus Protocol—Byte Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial-Bus Protocol—Byte Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EEPROM Interface Doubleword Data Collection . . . . . . . . . . . . . . . . . . . .
IRQ Implementation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Diagram Implementing CardBus Device Class
Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Signal Diagram of Suspend Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RI_OUT Functional Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Block Diagram of a Status/Enable Cell . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TP Cable Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Typical Compliant DC Isolated Outer Shield Termination . . . . . . . . . . . . .
Non-DC Isolated Outer Shield Termination . . . . . . . . . . . . . . . . . . . . . . . . .
Load Capacitance for the PCI7410 PHY . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommended Crystal and Capacitor Layout . . . . . . . . . . . . . . . . . . . . . . .
ExCA Register Access Through I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ExCA Register Access Through Memory . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessing CardBus Socket Registers Through PCI Memory . . . . . . . . . .
Test Load Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page
2–1
2–2
3–1
3–4
3–6
3–9
3–11
3–11
3–13
3–14
3–17
3–17
3–18
3–18
3–18
3–23
3–25
3–27
3–28
3–30
3–32
3–33
3–33
3–34
3–34
5–2
5–2
6–1
12–4
List of Tables
Table
1–1
2–1
2–2
2–3
2–4
2–5
2–6
2–7
2–8
2–9
2–10
2–11
2–12
2–13
2–14
2–15
2–16
2–17
2–18
3–1
3–2
3–3
3–4
3–5
3–6
3–7
3–8
3–9
3–10
3–11
3–12
3–13
3–14
3–15
3–16
3–17
3–18
Title
Terms and Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Signal Names by PDV Terminal Number . . . . . . . . . . . . . . . . . . . . . . . . . . .
Signal Names by GHK Terminal Number . . . . . . . . . . . . . . . . . . . . . . . . . . .
CardBus PC Card Signal Names Sorted Alphabetically . . . . . . . . . . . . . .
16-Bit PC Card Signal Names Sorted Alphabetically . . . . . . . . . . . . . . . . .
Power Supply Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PC Card Power Switch Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCI System Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCI Address and Data Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCI Interface Control Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multifunction and Miscellaneous Terminals . . . . . . . . . . . . . . . . . . . . . . . . .
16-Bit PC Card Address and Data Terminals . . . . . . . . . . . . . . . . . . . . . . .
16-Bit PC Card Interface Control Terminals . . . . . . . . . . . . . . . . . . . . . . . . .
CardBus PC Card Interface System Terminals . . . . . . . . . . . . . . . . . . . . . .
CardBus PC Card Address and Data Terminals . . . . . . . . . . . . . . . . . . . . .
CardBus PC Card Interface Control Terminals . . . . . . . . . . . . . . . . . . . . . .
IEEE 1394 Physical Layer Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supply Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UltraMedia Dedicated Socket Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCI Bus Master Command Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PC Card—Card Detect and Voltage Sense Connections . . . . . . . . . . . . .
Query Terminal Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Query Terminals – Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Query Terminals – Media Interface Implementation . . . . . . . . . . . . . . . . . .
TPS2221 Control Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TPS2211A Control Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Functionality of the ZV Output Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Terminals With Integrated Pullup Resistors . . . . . . . . . . . . . . . . . . . . . . . . .
CardBus Socket Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Firmware Loader I/O Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Firmware Loader Control Register Description . . . . . . . . . . . . . . . . . . . . . .
PCI7410 Registers Used to Program Serial-Bus Devices . . . . . . . . . . . . .
EEPROM Loading Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interrupt Mask and Flag Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PC Card Interrupt Events and Description . . . . . . . . . . . . . . . . . . . . . . . . . .
Interrupt Pin Register Cross Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SMI Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page
1–5
2–3
2–5
2–7
2–9
2–11
2–11
2–11
2–12
2–13
2–14
2–15
2–16
2–17
2–18
2–19
2–20
2–20
2–21
3–4
3–8
3–8
3–8
3–9
3–10
3–10
3–12
3–13
3–14
3–15
3–16
3–16
3–19
3–21
3–22
3–24
3–24
xi
3–19
3–20
3–21
3–22
4–1
4–2
4–3
4–4
4–5
4–6
4–7
4–8
4–9
4–10
4–11
4–12
4–13
4–14
4–15
4–16
4–17
4–18
4–19
4–20
4–21
4–22
4–23
4–24
4–25
5–1
5–2
5–3
5–4
5–5
5–6
5–7
5–8
5–9
5–10
5–11
5–12
xii
Requirements for Internal/External 1.8-V Core Power Supply . . . . . . . . .
Power-Management Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Function 2 Power-Management Registers . . . . . . . . . . . . . . . . . . . . . . . . . .
Function 3 Power-Management Registers . . . . . . . . . . . . . . . . . . . . . . . . . .
Bit Field Access Tag Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Functions 0 and 1 PCI Configuration Register Map . . . . . . . . . . . . . . . . . .
Command Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Status Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Secondary Status Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interrupt Pin Register Cross Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bridge Control Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Control Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Control Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General-Purpose Event Status Register Description . . . . . . . . . . . . . . . . .
General-Purpose Event Enable Register Description . . . . . . . . . . . . . . . .
General-Purpose Input Register Description . . . . . . . . . . . . . . . . . . . . . . . .
General-Purpose Output Register Description . . . . . . . . . . . . . . . . . . . . . .
Multifunction Routing Status Register Description . . . . . . . . . . . . . . . . . . .
Retry Status Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Card Control Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Device Control Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Management Capabilities Register Description . . . . . . . . . . . . . . .
Power Management Control/Status Register Description . . . . . . . . . . . . .
Power Management Control/Status Bridge Support Extensions
Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Bus Data Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Bus Index Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Bus Slave Address Register Description . . . . . . . . . . . . . . . . . . . . .
Serial Bus Control/Status Register Description . . . . . . . . . . . . . . . . . . . . . .
ExCA Registers and Offsets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ExCA Identification and Revision Register Description . . . . . . . . . . . . . . .
ExCA Interface Status Register Description . . . . . . . . . . . . . . . . . . . . . . . .
ExCA Power Control Register Description—82365SL Support . . . . . . . .
ExCA Power Control Register Description—82365SL-DF Support . . . . .
ExCA Interrupt and General Control Register Description . . . . . . . . . . . .
ExCA Card Status-Change Register Description . . . . . . . . . . . . . . . . . . . .
ExCA Card Status-Change Interrupt Configuration
Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ExCA Address Window Enable Register Description . . . . . . . . . . . . . . . .
ExCA I/O Window Control Register Description . . . . . . . . . . . . . . . . . . . . .
ExCA Memory Windows 0–4 Start-Address High-Byte
Registers Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ExCA Memory Windows 0–4 End-Address High-Byte
Registers Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–26
3–29
3–29
3–29
4–1
4–1
4–4
4–5
4–9
4–14
4–15
4–18
4–21
4–22
4–23
4–23
4–24
4–25
4–26
4–27
4–28
4–29
4–31
4–32
4–33
4–34
4–34
4–35
4–36
5–3
5–5
5–6
5–7
5–7
5–8
5–9
5–10
5–11
5–12
5–16
5–18
5–13
5–14
5–15
6–1
6–2
6–3
6–4
6–5
6–6
6–7
7–1
7–2
7–3
7–4
7–5
7–6
7–7
7–8
7–9
7–10
7–11
7–12
7–13
7–14
7–15
7–16
7–17
7–18
7–19
7–20
7–21
7–22
8–1
8–2
8–3
8–4
8–5
8–6
8–7
8–8
8–9
8–10
8–11
ExCA Memory Windows 0–4 Offset-Address High-Byte
Registers Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ExCA Card Detect and General Control Register Description . . . . . . . . .
ExCA Global Control Register Description . . . . . . . . . . . . . . . . . . . . . . . . .
CardBus Socket Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Socket Event Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Socket Mask Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Socket Present State Register Description . . . . . . . . . . . . . . . . . . . . . . . . .
Socket Force Event Register Description . . . . . . . . . . . . . . . . . . . . . . . . . .
Socket Control Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Socket Power Management Register Description . . . . . . . . . . . . . . . . . . .
Function 2 Configuration Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Command Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Status Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Class Code and Revision ID Register Description . . . . . . . . . . . . . . . . . . .
Latency Timer and Class Cache Line Size Register Description . . . . . . .
Header Type and BIST Register Description . . . . . . . . . . . . . . . . . . . . . . . .
OHCI Base Address Register Description . . . . . . . . . . . . . . . . . . . . . . . . . .
TI Base Address Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CardBus CIS Base Address Register Description . . . . . . . . . . . . . . . . . . .
Subsystem Identification Register Description . . . . . . . . . . . . . . . . . . . . . .
Interrupt Line Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCI Interrupt Pin Register—Read-Only INTPIN Per Function . . . . . . . . .
Minimum Grant and Maximum Latency Register Description . . . . . . . . .
OHCI Control Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Capability ID and Next Item Pointer Registers Description . . . . . . . . . . . .
Power Management Capabilities Register Description . . . . . . . . . . . . . . .
Power Management Control and Status Register Description . . . . . . . . .
Power Management Extension Registers Description . . . . . . . . . . . . . . . .
PCI PHY Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCI Miscellaneous Configuration Register . . . . . . . . . . . . . . . . . . . . . . . . .
Link Enhancement Control Register Description . . . . . . . . . . . . . . . . . . . .
Subsystem Access Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . .
OHCI Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OHCI Version Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GUID ROM Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Asynchronous Transmit Retries Register Description . . . . . . . . . . . . . . . .
CSR Control Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuration ROM Header Register Description . . . . . . . . . . . . . . . . . . . .
Bus Options Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuration ROM Mapping Register Description . . . . . . . . . . . . . . . . . . .
Posted Write Address Low Register Description . . . . . . . . . . . . . . . . . . . .
Posted Write Address High Register Description . . . . . . . . . . . . . . . . . . . .
Host Controller Control Register Description . . . . . . . . . . . . . . . . . . . . . . . .
5–20
5–21
5–22
6–1
6–2
6–3
6–4
6–6
6–7
6–8
7–1
7–3
7–4
7–5
7–5
7–6
7–6
7–7
7–8
7–9
7–10
7–10
7–11
7–11
7–12
7–13
7–14
7–14
7–15
7–16
7–17
7–18
8–1
8–4
8–5
8–6
8–7
8–8
8–9
8–11
8–11
8–12
8–13
xiii
8–12
8–13
8–14
8–15
8–16
8–17
8–18
8–19
8–20
8–21
8–22
8–23
8–24
8–25
8–26
8–27
8–28
8–29
8–30
8–31
8–32
8–33
8–34
8–35
9–1
9–2
9–3
9–4
10–1
10–2
10–3
10–4
10–5
10–6
10–7
10–8
10–9
11–1
11–2
11–3
11–4
11–5
11–6
xiv
Self-ID Count Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Isochronous Receive Channel Mask High Register Description . . . . . . .
Isochronous Receive Channel Mask Low Register Description . . . . . . . .
Interrupt Event Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interrupt Mask Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Isochronous Transmit Interrupt Event Register Description . . . . . . . . . . .
Isochronous Receive Interrupt Event Register Description . . . . . . . . . . .
Initial Bandwidth Available Register Description . . . . . . . . . . . . . . . . . . . . .
Initial Channels Available High Register Description . . . . . . . . . . . . . . . . .
Initial Channels Available Low Register Description . . . . . . . . . . . . . . . . .
Fairness Control Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Link Control Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Node Identification Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . .
PHY Control Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Isochronous Cycle Timer Register Description . . . . . . . . . . . . . . . . . . . . . .
Asynchronous Request Filter High Register Description . . . . . . . . . . . . .
Asynchronous Request Filter Low Register Description . . . . . . . . . . . . . .
Physical Request Filter High Register Description . . . . . . . . . . . . . . . . . . .
Physical Request Filter Low Register Description . . . . . . . . . . . . . . . . . . .
Asynchronous Context Control Register Description . . . . . . . . . . . . . . . . .
Asynchronous Context Command Pointer Register Description . . . . . . .
Isochronous Transmit Context Control Register Description . . . . . . . . . .
Isochronous Receive Context Control Register Description . . . . . . . . . . .
Isochronous Receive Context Match Register Description . . . . . . . . . . . .
TI Extension Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Isochronous Receive Digital Video Enhancements
Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Link Enhancement Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timestamp Offset Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Base Register Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Base Register Field Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page 0 (Port Status) Register Configuration . . . . . . . . . . . . . . . . . . . . . . . .
Page 0 (Port Status) Register Field Descriptions . . . . . . . . . . . . . . . . . . . .
Page 1 (Vendor ID) Register Configuration . . . . . . . . . . . . . . . . . . . . . . . . .
Page 1 (Vendor ID) Register Field Descriptions . . . . . . . . . . . . . . . . . . . . .
Page 7 (Vendor-Dependent) Register Configuration . . . . . . . . . . . . . . . . .
Page 7 (Vendor-Dependent) Register Field Descriptions . . . . . . . . . . . . .
Power Class Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Function 3 Configuration Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Command Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Status Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Class Code and Revision ID Register Description . . . . . . . . . . . . . . . . . . .
Base Address Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-Management Capabilities Register Description . . . . . . . . . . . . . . .
8–15
8–16
8–17
8–18
8–20
8–22
8–24
8–25
8–26
8–26
8–27
8–28
8–29
8–30
8–31
8–32
8–34
8–35
8–37
8–38
8–39
8–40
8–41
8–44
9–1
9–2
9–4
9–5
10–1
10–2
10–4
10–4
10–5
10–5
10–6
10–6
10–7
11–1
11–2
11–3
11–4
11–5
11–9
11–7
11–8
11–9
Power-Management Control/Status Register Description . . . . . . . . . . . . 11–10
Miscellaneous Control Register Description . . . . . . . . . . . . . . . . . . . . . . . 11–11
Subsystem Access Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . 11–12
xv
xvi
1 Introduction
The Texas Instruments PCI7410 device is an integrated single-socket UltraMedia PC Card controller with an IEEE
1394 open host controller link-layer controller (LLC) and two-port 1394 PHY. The PCI7410 device also includes a
dedicated interface that can be used as a Secure Digital (SD)/MultiMediaCard (MMC), or Memory Stick socket. This
high performance integrated solution provides the latest in PC Card, IEEE 1394, and UltraMedia technology.
1.1 Description
The PCI7410 CardBus controller is a four-function, 33-MHz PCI device compliant with the PCI Local Bus
Specification. Function 0 provides a PC Card socket controller compliant with the latest PC Card Standards and
UltraMedia specification. Function 1 provides a dedicated socket for either SD/MMC or Memory Stick. Function 2 of
the PCI7410 device is an integrated IEEE 1394 OHCI host controller and two-port PHY. Function 3 is the interface
to load the PCI7410 program RAM with firmware. The PCI7410 device provides features that make it the best choice
for bridging between the PCI bus and PC Cards, and supports any combination of 16-bit and CardBus cards powered
at 5 V or 3.3 V as required.
UltraMedia cards that comply with the PCMCIA Proposal 262 provide for very low cost flash media adapters since
the control logic is integrated into the PCI7410 device. The PCI7410 device supports SmartMedia adapters, Memory
Stick adapters and MMC/SD adapters.
There is no PCMCIA card and socket service software changes required to move systems from the existing CardBus
socket controller to the PCI7410 device. The PCI7410 device is register compatible with the Intel 82365SL–DF ExCA
controller and implements the host interface defined in the PC Card Standard. The PCI7410 internal data path logic
allows the host to access 8-, 16-, and 32-bit cards using full 32-bit PCI cycles for maximum performance. Independent
buffering and the pipeline architecture provide an unsurpassed performance level with sustained bursting. The
PCI7410 device can be programmed to accept posted writes to improve bus utilization. All card signals are internally
buffered to allow hot insertion and removal without external buffering.
Function 1 of the PCI7410 device provides a dedicated interface for either a Secure Digital (and MMC) or Memory
Stick socket. Secure Digital cards are based upon the MultiMediaCard (MMC). SD is essentially a superset of MMC.
The additional security features of the SD cards also allow their use in more-secure applications or in devices where
content protection is essential. Memory Stick cards are about the size of a stick of gum and are 2,8 mm thick.
Developed by Sony, there are two types of Memory Stick cards, the standard Memory Stick and MagicGate Memory
Stick. MagicGate technology provides security to Memory Stick cards so that they can be used to store and protect
copyrighted data.
Function 2 of the PCI7410 device is an integrated 1394a-2000 OHCI PHY/link-layer controller (LLC) device that is
fully compliant with the PCI Local Bus Specification, the PCI Bus Power Management Interface Specification, IEEE
Std 1394-1995, IEEE Std 1394a-2000, and the 1394 Open Host Controller Interface Specification. It is capable of
transferring data between the 33-MHz PCI bus and the 1394 bus at 100M bits/s, 200M bits/s, and 400M bits/s. The
PCI7410 device provides two 1394 ports that have separate cable bias (TPBIAS). The PCI7410 device also supports
the IEEE Std 1394a-2000 power-down features for battery-operated applications and arbitration enhancements.
As required by the 1394 Open Host Controller Interface Specification (OHCI) and IEEE Std 1394a-2000, internal
control registers are memory-mapped and non-prefetchable. The PCI configuration header is accessed through
configuration cycles specified by PCI, and it provides plug-and-play (PnP) compatibility. Furthermore, the PCI7410
device is compliant with the PCI Bus Power Management Interface Specification as specified by the PC 2001 Design
Guide requirements. The PCI7410 device supports the D0, D1, D2, and D3 power states.
Function 3 of the PCI7410 device is the interface to load the PCI7410 program RAM with firmware. This function
provides an I/O window that a software driver uses to load the PCI7410 firmware into the internal RAM.
The PCI7410 design provides PCI bus master bursting, and it is capable of transferring a cacheline of data at 132M
bytes/s after connection to the memory controller. Because PCI latency can be large, deep FIFOs are provided to
buffer the 1394 data.
1–1
The PCI7410 device provides physical write posting buffers and a highly-tuned physical data path for SBP-2
performance. The PCI7410 device also provides multiple isochronous contexts, multiple cacheline burst transfers,
advanced internal arbitration, and bus-holding buffers.
The PCI7410 PHY-layer provides the digital and analog transceiver functions needed to implement a two-port node
in a cable-based 1394 network. Each cable port incorporates two differential line transceivers. The transceivers
include circuitry to monitor the line conditions as needed for determining connection status, for initialization and
arbitration, and for packet reception and transmission.
The PCI7410 PHY-layer requires only an external 24.576-MHz crystal as a reference for the cable ports. An external
clock may be provided instead of a crystal. An internal oscillator drives an internal phase-locked loop (PLL), which
generates the required 393.216-MHz reference signal. This reference signal is internally divided to provide the clock
signals that control transmission of the outbound encoded strobe and data information. A 49.152-MHz clock signal
is supplied to the integrated LLC for synchronization and is used for resynchronization of the received data. Data bits
to be transmitted through the cable ports are received from the integrated LLC and are latched internally in
synchronization with the 49.152-MHz system clock. These bits are combined serially, encoded, and transmitted at
98.304M, 196.608M, or 393.216M bits/s (referred to as S100, S200, or S400 speeds, respectively) as the outbound
data-strobe information stream. During transmission, the encoded data information is transmitted differentially on the
twisted-pair B (TPB) cable pair(s), and the encoded strobe information is transmitted differentially on the twisted-pair
A (TPA) cable pair(s).
Various implementation specific functions and general-purpose inputs and outputs are provided through several
multifunction terminals. These terminals present a system with options, such as PCI LOCK and parallel IRQs.
ACPI-complaint general-purpose events may be programmed and controlled through the multifunction terminals, and
an ACPI-compliant programming interface is included for the general-purpose inputs and outputs.
The PCI7410 device is compliant with the latest PCI Bus Power Management Specification, and provides several
low-power modes, which enable the host power system to further reduce power consumption. The PCI7410 device
also has a four-pin interface compatible with both the TI TPS2211 and TPS2221 power switches.
An advanced CMOS process achieves low power consumption and allows the PCI7410 device to operate at PCI clock
rates up to 33 MHz.
1.2 Features
The PCI7410 device supports the following features:
1–2
•
PC Card Standard 8.0 compliant
•
PCI Bus Power Management Interface Specification 1.1 compliant
•
Advanced Configuration and Power Interface (ACPI) Specification 2.0 compliant
•
PCI Local Bus Specification Revision 2.3 compliant
•
PC 98/99 and PC2001 compliant
•
Compliant with the PCI Bus Interface Specification for PCI-to-CardBus Bridges
•
Fully compliant with provisions of IEEE Std 1394-1995 for a high-performance serial bus and IEEE Std
1394a-2000
•
Fully compliant with 1394 Open Host Controller Interface Specification 1.1
•
1.8-V core logic and 3.3-V I/O cells with internal voltage regulator to generate 1.8-V core VCC
•
Universal PCI interfaces compatible with 3.3-V and 5-V PCI signaling environments
•
Supports PC Card or CardBus with hot insertion and removal
•
Supports 132-MBps burst transfers to maximize data throughput on both the PCI bus and the CardBus
•
Supports serialized IRQ with PCI interrupts
•
Programmable multifunction terminals
•
Many interrupt modes supported
•
Serial ROM interface for loading subsystem ID and subsystem vendor ID
•
ExCA-compatible registers are mapped in memory or I/O space
•
Intel 82365SL–DF register compatible
•
Supports ring indicate, SUSPEND, and PCI CCLKRUN protocol and PCI bus Lock (LOCK)
•
Provides VGA/palette memory and I/O, and subtractive decoding options, LED activity terminals
•
Fully interoperable with FireWire and i.LINK implementations of IEEE Std 1394
•
Compliant with Intel Mobile Power Guideline 2000
•
Full IEEE Std 1394a-2000 support includes: connection debounce, arbitrated short reset, multispeed
concatenation, arbitration acceleration, fly-by concatenation, and port disable/suspend/resume
•
Power-down features to conserve energy in battery-powered applications include: automatic device power
down during suspend, PCI power management for link-layer, and inactive ports powered down,
ultralow-power sleep mode
•
Two IEEE Std 1394a-2000 fully compliant cable ports at 100M bits/s, 200M bits/s, and 400M bits/s
•
Cable ports monitor line conditions for active connection to remote node
•
Cable power presence monitoring
•
Separate cable bias (TPBIAS) for each port
•
Physical write posting of up to three outstanding transactions
•
PCI burst transfers and deep FIFOs to tolerate large host latency
•
External cycle timer control for customized synchronization
•
Extended resume signaling for compatibility with legacy DV components
•
PHY-Link logic performs system initialization and arbitration functions
•
PHY-Link encode and decode functions included for data-strobe bit level encoding
•
PHY-Link incoming data resynchronized to local clock
•
Low-cost 24.576-MHz crystal provides transmit and receive data at 100M bits/s, 200M bits/s, and
400M bits/s
•
Node power class information signaling for system power management
•
Register bits give software control of contender bit, power class bits, link active control bit, and IEEE Std
1394a-2000 features
•
Isochronous receive dual-buffer mode
•
Out-of-order pipelining for asynchronous transmit requests
•
Register access fail interrupt when the PHY SCLK is not active
•
PCI power-management D0, D1, D2, and D3 power states
•
Initial bandwidth available and initial channels available registers
•
PME support per 1394 Open Host Controller Interface Specification
•
Advanced submicron, low-power CMOS technology
1.3 Related Documents
•
Advanced Configuration and Power Interface (ACPI) Specification (Revision 2.0)
1–3
•
1394 Open Host Controller Interface Specification (Release 1.1)
•
IEEE Standard for a High Performance Serial Bus (IEEE Std 1394-1995)
•
IEEE Standard for a High Performance Serial Bus—Amendment 1 (IEEE Std 1394a-2000)
•
PC Card Standard (Release 8.0)
•
PC 2001 Design Guide
•
PCI Bus Power Management Interface Specification (Revision 1.1)
•
PCI Local Bus Specification (Revision 2.3)
•
Mobile Power Guidelines 2000
•
Serial Bus Protocol 2 (SBP-2)
•
Serialized IRQ Support for PCI Systems
•
PCI Mobile Design Guide
•
PCI Bus Power Management Interface Specification for PCI to CardBus Bridges
•
PCI14xx Implementation Guide for D3 Wake-Up
•
PCI to PCMCIA CardBus Bridge Register Description
•
Texas Instruments TPS2221 product data sheet, SLVS419
•
Texas Instruments TPS2211A product data sheet, SLVS282
•
SD Memory Card Specifications, March 2000
•
The Multimedia Card System Specification, version 3.2, January 2002
•
SmartMedia Standard 2000, May 19, 2000
•
Memory Stick Standard, Format Specification, version 1.3, July 2000
•
ISO/IEC 7816 Series, Parts 1–10
•
PC/SC Workgroup Specifications, version 1.0, Parts 1–8
1.4 Trademarks
Intel is a trademark of Intel Corporation.
TI, UltraMedia, and MicroStar BGA are trademarks of Texas Instruments.
FireWire is a trademark of Apple Computer, Inc.
i.LINK is a trademark of Sony Corporation of America.
Memory Stick is a trademark of Sony Kabushiki Kaisha TA Sony Corporation, Japan.
SmartMedia is a trademark of Kabushiki Kaisha Toshiba DBA Toshiba Corporation, Japan.
Other trademarks are the property of their respective owners.
1–4
1.5 Terms and Definitions
Terms and definitions used in this document are given in Table 1–1.
Table 1–1. Terms and Definitions
TERM
DEFINITIONS
ATA
AT (advanced technology, as in PC AT) attachment interface
ATA driver
An existing host software component that loads when any flash media adapter and card is inserted into a PC Card
socket. This driver is logically attached to a predefined CIS provided by the PCI7410 device when the adapter and
media are both inserted.
CIS
Card information structure. Tuple list defined by the PC Card standard to communicate card information to the host
computer
CSR
Control and status register
Flash Media
SmartMedia, Memory Stick, MMC, or SD/MMC Flash operating in an ATA compatible mode
Function 3 firmware loader
A hardware element of the PCI7410 that provides a software interface to the TI firmware loader driver to load the
program RAM with firmware
ISO/IEC 7816
The Smart Card standard
Memory Stick
A small-form-factor flash interface that is defined, promoted, and licensed by Sony
MMC
MultiMediaCard. Specified by the MMC Association, and scope is encompassed by the SD Flash specification.
OHCI
Open host controller interface
PCMCIA
Personal Computer Memory Card International Association. Standards body that governs the PC Card standards
RSVD
Reserved for future use
SD Flash
Secure Digital Flash. Standard governed by the SD Association
SmartMedia
Also known as SSFDC, defined by Toshiba and governed by SSFDC Forum
SPI
Serial peripheral interface, a general-purpose synchronous serial interface. For more information, see the
Multimedia Card System Specification, version 3.2.
SSFDC
Solid State Floppy Disk Card. The SSFDC Forum specifies SmartMedia
TI firmware loader driver
A qualified software component provided by Texas Instruments that loads the firmware into the PCI7410 on power
up and initialization.
TI Smart Card driver
A qualified software component provided by Texas Instruments that loads when an UltraMedia-based Smart Card
adapter is inserted into a PC Card slot. This driver is logically attached to a CIS provided by the PCI7410 when the
adapter and media are both inserted.
UART
Universal asynchronous receiver and transmitter
UltraMedia
De facto industry standard promoted by Texas Instruments that integrates CardBus, Smart Card, Memory Stick,
MultiMediaCard/Secure Digital and SmartMedia functionality into one controller.
1.6 Ordering Information
ORDERING NUMBER
NAME
VOLTAGE
PACKAGE
PCI7410
PC Card, UltraMedia, and Integrated 1394a-2000 OHCI
Two-Port PHY/Link-Layer Controller
3.3-V, 5-V tolerant I/Os
208-terminal LQFP (PDV)
209-ball PBGA (GHK)
1–5
1–6
2 Terminal Descriptions
The PCI7410 device is available in two packages, a 208-terminal quad flatpack (PDV) and a 209-terminal MicroStar
BGA package (GHK). The terminal layout for the GHK package is shown in Figure 2–1. The terminal layout with
signal names for the PDV package is shown in Figure 2–2.
W
PAR
VCCP
GND
AD7
VCC
AD3
PC1
TPB0N
TPA0N
R0
TPB1N
TPA1N
V
AD13
AD11
C/BE0
AD4
AD2
PC0
TPB0P
TPA0P
R1
TPB1P
TPA1P
U
C/BE1
AD12
AD8
AD5
AD1
SKT_
SEL0
ANALOG
T
SERR
R
VCC
DVSEL
PERR
P
AD16
C/BE2
IRDY
N
GND
AD19
AD18
GND
TPBIAS0
ANALOG ANALOG
VCC
VCC
TPBIAS1
FILTER0
AD15
AD10
AD6
AD0
SKT_
SEL1
STOP
TRDY
AD14
AD9
PC2
CPS
FRAME
AD17
ANALOG ANALOG ANALOG
VCC
GND
GND
NC
NC
NC
NC
FILTER1
XI
XO
GND
NC
VDPLL
CNA
PHY_
TEST
_MA
VSPLL
UM_
PWR_
CTRL
SD_WP
SD_DATA1/
MS_BS
IRQ
MS_INS MS_SCLK
SD_CD SD_CLK
M
VCC
AD23
AD22
AD20
AD21
L
VCCP
AD25
AD24
IDSEL
C/BE3
CAD2
//D11
K
GND
AD29
AD28
AD27
AD26
J
GNT
REQ
RI_OUT
/PME
AD31
AD30
H
PCLK
GRST
PRST
G
VCC
VR_
PORT
F
NC
MS_RFU5 MS_RFU7
MS_SDIO
SD_DATA0
SD_DATA2
SD_CMD
SD_SC
CAD0
//D3
CCD1
//CD1
VR_
PORT
VCC
CAD6
//D13
CAD3
//D5
CAD4
//D12
CAD1
//D4
GND
CAD8
//D15
CC/BE0
//CE1
CAD7
//D7
CRSVD
//D14
CAD5
//D6
VR_EN MFUNC6
CAD11
//OE
CAD12
//A11
CAD10
//CE2
CAD9
//A10
VCC
SUSPEND
MFUNC4 MFUNC1
VCCCB
CC/BE1
//A8
CAD15 CAD13
//IOWR //IORD
GND
MFUNC5 MFUNC3 MFUNC2
MFUNC0 CLK_48
RSVD
CRSVD CAD27 CAUDIO CAD26
//BVD2
//D2
//D0
//A0
CPAR
//A13
CPERR
//A14
CRSVD CAD16
//A18
//A17
CAD14
//A9
VD1/
VCCD0
RSVD
CAD31
//D10
CSTOP CBLOCK
//A19
//A20
VCC
E
GND
D
SDA
SPKROUT
SCL
NC
CAD28 CSERR CAD25
//D8
//A1
//WAIT
CVS2
//VS2
CAD21
//A5
CIRDY
//A15
CAD18 CTRDY
//A7
//A22
CGNT//
WE
VD2/
VPPD1
RSVD
RSVD
CAD30
//D9
B
VD0/
VCCD1
RSVD
RSVD
CAD29 CCLKRUN CVS1
//WP
//D1
//VS1
VD3/
VPPD0
VCC
RSVD
GND
VCC
CSTSCHG
//BVD1
GND
VCCCB
CAD23
//A3
VCC
CAD19
//A25
GND
CDEVSEL
//A21
4
5
6
7
8
9
10
11
12
13
14
15
16
A
1
2
3
CCD2
//CD2
CINT// CAD24
//A2
READY
C
CAD22
//A4
CAD20 CC/BE2
//A6
//A12
CCLK
//A16
CC/BE3 CREQ// CRST// CAD17 CFRAME
//A23
//REG INPACK RESET //A24
17
18
19
Figure 2–1. PCI7410 GHK-Package Terminal Diagram
2–1
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
CGNT//WE
CSTOP//A20
CPERR//A14
CBLOCK//A19
CPAR//A13
VCC
CRSVD//A18
CC/BE1//A8
CAD16//A17
CAD14//A9
VCCCB
CAD15//IOWR
CAD13//IORD
GND
CAD12//A11
CAD11//OE
CAD10//CE2
CAD9//A10
VCC
CC/BE0//CE1
CAD8//D15
CAD7//D7
CRSVD//D14
CAD5//D6
CAD6//D13
CAD3//D5
CAD4//D12
CAD1//D4
GND
CAD2//D11
CAD0//D3
CCD1//CD1
VR_PORT
VCC
SD_DATA2
MS_RFU7/SD_CD/DATA3
MS_RFU5/SD_CMD
MS_SCLK/SD_CLK
MS_SDIOI/SD_DATA0
MS_BS/SD_DATA1/IRQ
SD_WP
MS_INS/SD_CD
GND
UM_PWR_CTRL
PHY_TEST_MA
CNA
XO
XI
VSPLL
VDPLL
FILTER1
FILTER0
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
PCI7410
SDA
SCL
MFUNC0
MFUNC1
SPKROUT
GND
MFUNC2
MFUNC3
MFUNC4
MFUNC5
MFUNC6
SUSPEND
VR_PORT
VCC
VR_EN
PRST
GRST
PCLK
GNT
REQ
RI_OUT/PME
AD31
AD30
GND
AD29
AD28
AD27
AD26
VCCP
AD25
AD24
C/BE3
IDSEL
VCC
AD23
AD22
AD21
AD20
GND
AD19
AD18
AD17
AD16
C/BE2
FRAME
IRDY
VCC
TRDY
DEVSEL
STOP
PERR
SERR
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
CDEVSEL//A21
CCLK//A16
CTRDY//A22
CIRDY//A15
CFRAME//A23
GND
CC/BE2//A12
CAD17//A24
CAD18//A7
CAD19//A25
CVS2//VS2
CAD20//A6
CRST//RESET
VCC
CAD21//A5
CAD22//A4
CREQ//INPACK
CAD23//A3
VCCCB
CC/BE3//REG
CAD24//A2
CAD25//A1
CAD26//A0
GND
CVS1//VS1
CINT//READY(IREQ)
CSERR//WAIT
CAUDIO//BVD2(SPKR)
CSTSCHG//BVD1(STSCHG/RI)
CCLKRUN//WP(IOIS16)
CCD2//CD2
CAD27//D0
CAD28//D8
VCC
CAD29//D1
CAD30//D9
CRSVD//D2
CAD31//D10
GND
RSVD
RSVD
RSVD
RSVD
RSVD
RSVD
RSVD
VCC
CLK_48
VD0/VCCD1
VD1/VCCD0
VD2/VPPD1
VD3/VPPD0
156
155
154
153
152
151
150
149
148
147
146
145
144
143
142
141
140
139
138
137
136
135
134
133
132
131
130
129
128
127
126
125
124
123
122
121
120
PDV LOW-PROFILE QUAD FLAT PACKAGE
(LQFP)
TOP VIEW
Figure 2–2. PCI7410 PDV-Package Terminal Diagram
2–2
104
103
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
NC
TPBIAS1
NC
TPA1P
NC
TPA1N
ANALOGVCC
ANALOGGND
TPB1P
TPB1N
NC
ANALOGVCC
R1
R0
ANALOGGND
NC
TPBIAS0
TPA0P
TPA0N
ANALOGVCC
NC
ANALOGGND
TPB0P
TPB0N
CPS
SKT_SEL1
SKT_SEL0
PC0
PC1
PC2
AD0
AD1
AD2
AD3
VCC
AD4
AD5
AD6
AD7
C/BE0
AD8
AD9
GND
AD10
AD11
AD12
VCCP
AD13
AD14
AD15
C/BE1
PAR
Table 2–1 and Table 2–2 list the terminal assignments arranged in terminal-number order, with corresponding signal
names for both CardBus and 16-bit PC Cards; Table 2–1 is for terminals on the PDV package and Table 2–2 is for
terminals on the GHK package. Table 2–3 and Table 2–4 list the terminal assignments arranged in alphanumerical
order by signal name, with corresponding terminal numbers for both PDV and GHK packages; Table 2–3 is for
CardBus signal names and Table 2–4 is for 16-bit PC Card signal names.
Terminal E5 on the GHK package is an identification ball used for device orientation; it has no internal connection
within the device.
Table 2–1. Signal Names by PDV Terminal Number
TERM
TERM.
NO.
SIGNAL NAME
TERM
TERM.
NO.
SIGNAL NAME
CardBus
PC Card
16-Bit
PC Card
TERM
TERM.
NO.
SIGNAL NAME
CardBus PC
Card
16-Bit
PC Card
CardBus
PC Card
16-Bit
PC Card
1
SDA
SDA
39
GND
GND
77
PC0
PC0
2
SCL
SCL
40
AD19
AD19
78
SKT_SEL0
SKT_SEL0
3
MFUNC0
MFUNC0
41
AD18
AD18
79
SKT_SEL1
SKT_SEL1
4
MFUNC1
MFUNC1
42
AD17
AD17
80
CPS
CPS
5
SPKROUT
SPKROUT
43
AD16
AD16
81
TPB0N
TPB0N
6
GND
GND
44
C/BE2
C/BE2
82
TPB0P
TPB0P
7
MFUNC2
MFUNC2
45
FRAME
FRAME
83
ANALOGGND
ANALOGGND
8
MFUNC3
MFUNC3
46
IRDY
IRDY
84
NC
NC
9
MFUNC4
MFUNC4
47
ANALOGVCC
MFUNC5
48
VCC
TRDY
ANALOGVCC
MFUNC5
VCC
TRDY
85
10
86
TPA0N
TPA0N
11
MFUNC6
MFUNC6
49
DEVSEL
DEVSEL
87
TPA0P
TPA0P
12
SUSPEND
SUSPEND
50
STOP
STOP
88
TPBIAS0
TPBIAS0
13
VR_PORT
VR_PORT
51
PERR
PERR
89
NC
NC
14
VCC
VR_EN
52
SERR
SERR
90
ANALOGGND
ANALOGGND
15
VCC
VR_EN
53
PAR
PAR
91
R0
R0
16
PRST
PRST
54
C/BE1
C/BE1
92
R1
R1
17
GRST
GRST
55
AD15
AD15
93
ANALOGVCC
ANALOGVCC
18
PCLK
PCLK
56
AD14
AD14
94
NC
NC
19
GNT
GNT
57
AD13
AD13
95
TPB1N
TPB1N
20
REQ
REQ
58
TPB1P
TPB1P
RI_OUT/PME
RI_OUT/PME
59
VCCP
AD12
96
21
VCCP
AD12
97
ANALOGGND
ANALOGGND
22
AD31
AD31
60
AD11
AD11
98
ANALOGVCC
ANALOGVCC
23
AD30
AD30
61
AD10
AD10
99
TPA1N
TPA1N
24
GND
GND
62
GND
GND
100
NC
NC
25
AD29
AD29
63
AD9
AD9
101
TPA1P
TPA1P
26
AD28
AD28
64
AD8
AD8
102
NC
NC
27
AD27
AD27
65
C/BE0
C/BE0
103
TPBIAS1
TPBIAS1
28
AD26
AD26
66
AD7
AD7
104
NC
NC
29
VCCP
AD25
67
AD6
AD6
105
FILTER0
FILTER0
30
VCCP
AD25
68
AD5
AD5
106
FILTER1
FILTER1
31
AD24
AD24
69
AD4
AD4
107
VDPLL
VDPLL
32
C/BE3
C/BE3
70
VSPLL
VSPLL
IDSEL
IDSEL
71
VCC
AD3
108
33
VCC
AD3
109
XI
XI
34
VCC
AD23
VCC
AD23
72
AD2
AD2
110
XO
XO
35
73
AD1
AD1
111
CNA
CNA
36
AD22
AD22
74
AD0
AD0
112
PHY_TEST_MA
PHY_TEST_MA
37
AD21
AD21
75
PC2
PC2
113
UM_PWR_CTRL
UM_PWR_CTRL
38
AD20
AD20
76
PC1
PC1
114
GND
GND
2–3
Table 2–1. Signal Names by PDV Terminal Number (Continued)
SIGNAL NAME
TERM.
TERM
NO.
2–4
CardBus
PC Card
16-Bit
PC Card
115
MS_INS/
SD_CD
MS_INS/
SD_CD
116
SD_WP
117
SIGNAL NAME
TERM.
TERM
NO.
CardBus
PC Card
16-Bit
PC Card
147
CAD14
A9
SD_WP
148
CAD16
MS_BS/
SD_DATA1/IRQ
MS_BS/
SD_DATA1/IRQ
149
118
MS_SDIO/
SD_DATA0
MS_SDIO/
SD_DATA0
119
MS_SCLK/
SD_CLK
120
SIGNAL NAME
TERM.
TERM
NO.
CardBus PC
Card
16-Bit
PC Card
179
CAD26
A0
A17
180
GND
GND
CC/BE1
A8
181
CVS1
VS1
150
CRSVD
A18
182
CINT
READY(IREQ)
MS_SCLK/
SD_CLK
151
VCC
VCC
183
CSERR
WAIT
MS_RFU5/
SD_CMD
MS_RFU5/
SD_CMD
152
CPAR
A13
184
CAUDIO
BVD2(SPKR)
121
MS_RFU7/
SD_CD/DATA3
MS_RFU7/
SD_CD/DATA3
153
CBLOCK
A19
185
CSTSCHG
BVD1(STSCHG/RI)
122
SD_DATA2
SD_DATA2
154
CPERR
A14
186
CCLKRUN
WP(IOIS1)
123
VCC
VR_PORT
155
CSTOP
A20
187
CCD2
CD2
124
VCC
VR_PORT
156
CGNT
WE
188
CAD27
D0
125
CCD1
CD1
157
CDEVSEL
A21
189
CAD28
D8
126
CAD0
D3
158
CCLK
A16
190
127
CAD2
D11
159
CTRDY
A22
191
VCC
CAD29
VCC
D1
128
GND
GND
160
CIRDY
A15
192
CAD30
D9
129
CAD1
D4
161
CFRAME
A23
193
CRSVD
D2
130
CAD4
D12
162
GND
GND
194
CAD31
D10
131
CAD3
D5
163
CC/BE2
A12
195
GND
GND
132
CAD6
D13
164
CAD17
A24
196
RSVD
RSVD
133
CAD5
D6
165
CAD18
A7
197
RSVD
RSVD
134
CRSVD
D14
166
CAD19
A25
198
RSVD
RSVD
135
CAD7
D7
167
CVS2
VS2
199
RSVD
RSVD
136
CAD8
D15
168
CAD20
A6
200
RSVD
RSVD
137
CC/BE0
CE1
169
CRST
RESET
201
RSVD
RSVD
138
VCC
CAD9
VCC
A10
170
VCC
A5
RSVD
RSVD
171
VCC
CAD21
202
139
203
140
CAD10
CE2
172
CAD22
A4
204
VCC
CLK_48
VCC
CLK_48
141
CAD11
OE
173
CREQ
INPACK
205
VD0/VCCD1
VD0/VCCD1
142
CAD12
A11
174
CAD23
A3
206
VD1/VCCD0
VD1/VCCD0
207
VD2/VPPD1
VD2/VPPD1
208
VD3/VPPD0
VD3/VPPD0
143
GND
GND
175
144
CAD13
IORD
176
VCCCB
CC/BE3
VCCCB
REG
145
CAD15
IOWR
177
CAD24
A2
146
VCCCB
VCCCB
178
CAD25
A1
Table 2–2. Signal Names by GHK Terminal Number
SIGNAL NAME
TERM.
TERM
NO.
CardBus PC
Card
16-Bit
PC Card
A04
VD3/VPPD0
VD3/VPPD0
A05
A06
VCC
RSVD
A07
A08
SIGNAL NAME
TERM.
TERM
NO.
SIGNAL NAME
TERM.
TERM
NO.
CardBus
PC Card
16-Bit
PC Card
E07
RSVD
RSVD
H06
VCC
RSVD
E08
CAD31
D10
H14
CAD11
OE
E09
CAD28
D8
H15
CAD12
A11
GND
GND
E10
CSERR
WAIT
H17
CAD10
CE2
VCC
BVD1(STSCHG/RI)
E11
CAD25
A1
H18
CAD9
A10
A09
VCC
CSTSCHG
E12
CAD21
A5
H19
A10
GND
GND
E13
CAD18
A7
J01
VCC
GNT
VCC
GNT
A11
VCCCB
CAD23
VCCCB
A3
E14
CTRDY
A22
J02
REQ
REQ
E17
CSTOP
A20
J03
RI_OUT/PME
RI_OUT/PME
VCC
A25
E18
CBLOCK
A19
J05
AD31
AD31
A14
VCC
CAD19
E19
AD30
GND
F01
VCC
MFUNC5
AD30
GND
VCC
MFUNC5
J06
A15
J14
CAD8
D15
A16
CDEVSEL
A21
F02
MFUNC3
MFUNC3
J15
CC/BE0
CE1
B05
VD0/VCCD1
VD0/VCCD1
F03
MFUNC2
MFUNC2
J17
CAD7
D7
B06
RSVD
RSVD
F05
MFUNC0
MFUNC0
J18
CRSVD
D14
B07
RSVD
RSVD
F06
CLK_48
CLK_48
J19
CAD5
D6
B08
CAD29
D1
F07
RSVD
RSVD
K01
GND
GND
B09
CCLKRUN
WP(IOIS16)
F08
CRSVD
D2
K02
AD29
AD29
A12
A13
CardBus
PC Card
16-Bit
PC Card
MFUNC6
MFUNC6
B10
CVS1
VS1
F09
CAD27
D0
K03
AD28
AD28
B11
CC/BE3
REG
F10
CAUDIO
BVD2(SPKR)
K05
AD27
AD27
B12
CREQ
INPACK
F11
CAD26
A0
K06
AD26
AD26
B13
CRST
RESET
F12
CVS2
VS2
K14
CAD6
D13
B14
CAD17
A24
F13
CIRDY
A15
K15
CAD3
D5
B15
CFRAME
A23
F14
CPAR
A13
K17
CAD4
D12
C05
VD2/VPPD1
VD2/VPPD1
F15
CPERR
A14
K18
CAD1
D4
C06
RSVD
RSVD
F17
CRSVD
A18
K19
GND
GND
C07
RSVD
RSVD
F18
CAD16
A17
L01
C08
CAD30
D9
F19
CAD14
A9
L02
VCCP
AD25
VCCP
AD25
C09
CCD2
CD2
G01
AD24
READY(IREQ)
G02
VCC
VR_PORT
AD24
CINT
VCC
VR_PORT
L03
C10
L05
IDSEL
IDSEL
C11
CAD24
A2
G03
SUSPEND
SUSPEND
L06
C/BE3
C/BE3
C12
CAD22
A4
G05
MFUNC4
MFUNC4
L14
CAD2
D11
C13
CAD20
A6
G06
MFUNC1
MFUNC1
L15
CAD0
D3
C14
CC/BE2
A12
G14
CD1
A16
G15
VCCCB
A8
CCD1
CCLK
VCCCB
CC/BE1
L17
C15
L18
VR_PORT
VR_PORT
D01
SDA
SDA
G17
CAD15
IOWR
L19
D19
CGNT
WE
G18
CAD13
IORD
M01
VCC
VCC
VCC
VCC
E01
GND
GND
G19
GND
GND
M02
AD23
AD23
E02
SPKROUT
SPKROUT
H01
PCLK
PCLK
M03
AD22
AD22
E03
SCL
SCL
H02
GRST
GRST
M05
AD20
AD20
E05
NC
NC
H03
PRST
PRST
M06
AD21
AD21
E06
VD1/VCCD0
VD1/VCCD0
H05
VR_EN
VR_EN
M14
MS_INS/
SD_CD
MS_INS/
SD_CD
2–5
Table 2–2. Signal Names by GHK Terminal Number (Continued)
SIGNAL NAME
TERM.
TERM
NO.
2–6
SIGNAL NAME
CardBus
PC Card
16-Bit
PC Card
M15
MS_SCLK/
SD_CLK
MS_SCLK/
SD_CLK
M17
MS_RFU5/
SD_CMD
M18
TERM.
TERM
NO.
SIGNAL NAME
CardBus
PC Card
16-Bit
PC Card
P17
CNA
CNA
MS_RFU5/
SD_CMD
P18
PHY_TEST_MA
MC_RFU7/
SD_CD/DATA3
MC_RFU7/
SD_CD/DATA3
P19
M19
SD_DATA2
SD_DATA2
R01
N01
GND
GND
N02
AD19
N03
AD18
N05
FRAME
TERM.
TERM
NO.
CardBus
PC Card
16-Bit
PC Card
U13
ANALOGVCC
ANALOGVCC
PHY_TEST_MA
U14
ANALOGVCC
ANALOGVCC
GND
GND
U15
TPBIAS1
TPBIAS1
VCC
DEVSEL
VCC
DEVSEL
V05
AD13
AD13
R02
V06
AD11
AD11
AD19
R03
PERR
PERR
V07
C/BE0
C/BE0
AD18
R06
AD15
AD15
V08
AD4
AD4
FRAME
R07
AD10
AD10
V09
AD2
AD2
N06
AD17
AD17
R08
AD6
AD6
V10
PC0
PC0
N14
VSPLL
VSPLL
R09
AD0
AD0
V11
TPB0P
TPB0P
N15
UM_PWR_CTRL
UM_PWR_CTRL
R10
SKT_SEL1
SKT_SEL1
V12
TPA0P
TPA0P
N17
SD_WP
SD_WP
R11
ANALOGVCC
ANALOGVCC
V13
R1
R1
N18
MS_BS/
SD_DATA1/IRQ
MS_BS/
SD_DATA1/IRQ
R12
ANALOGGND
ANALOGGND
V14
TPB1P
TPB1P
N19
MS_SDIO/
SD_DATA0
MS_SDIO/
SD_DATA0
R13
ANALOGGND
ANALOGGND
V15
TPA1P
TPA1P
P01
AD16
AD16
R14
NC
NC
W04
PAR
PAR
P02
C/BE2
C/BE2
R17
FILTER1
FILTER1
W05
VCCP
GND
VCCP
GND
P03
IRDY
IRDY
R18
XI
XI
W06
P05
STOP
STOP
R19
XO
XO
W07
AD7
AD7
P06
TRDY
TRDY
T01
SERR
SERR
W08
P07
AD14
AD14
T19
FILTER0
FILTER0
W09
VCC
AD3
VCC
AD3
P08
AD9
AD9
U05
C/BE1
C/BE1
W10
PC1
PC1
P09
PC2
PC2
U06
AD12
AD12
W11
TPB0N
TPB0N
P10
CPS
CPS
U07
AD8
AD8
W12
TPA0N
TPA0N
P11
NC
NC
U08
AD5
AD5
W13
R0
R0
P12
NC
NC
U09
AD1
AD1
W14
TPB1N
TPB1N
P13
NC
NC
U10
SKT_SEL0
SKT_SEL0
W15
TPA1N
TPA1N
W16
NC
NC
P14
NC
NC
U11
ANALOGGND
ANALOGGND
P15
VDPLL
VDPLL
U12
TPBIAS0
TPBIAS0
Table 2–3. CardBus PC Card Signal Names Sorted Alphabetically
SIGNAL NAME
TERMINAL NUMBER
PDV
GHK
AD0
74
R09
AD1
73
U09
AD2
72
V09
AD3
71
AD4
69
AD5
68
AD6
AD7
SIGNAL NAME
TERMINAL NUMBER
PDV
GHK
CAD6
132
K14
CAD7
135
J17
CAD8
136
J14
W09
CAD9
139
V08
CAD10
140
U08
CAD11
141
67
R08
CAD12
66
W07
CAD13
AD8
64
U07
AD9
63
AD10
AD11
SIGNAL NAME
TERMINAL NUMBER
PDV
GHK
CIRDY
160
F13
CLK_48
204
F06
CNA
111
P17
H18
CPAR
152
F14
H17
CPERR
154
F15
H14
CPS
80
P10
142
H15
CREQ
173
B12
144
G18
CRST
169
B13
CAD14
147
F19
CRSVD
134
F08
P08
CAD15
145
G17
CRSVD
150
F17
61
R07
CAD16
148
F18
CRSVD
193
J18
60
V06
CAD17
164
B14
CSERR
183
E10
AD12
59
U06
CAD18
165
E13
CSTOP
155
E17
AD13
57
V05
CAD19
166
A14
CSTSCHG
185
A09
AD14
56
P07
CAD20
168
C13
CTRDY
159
E14
AD15
55
R06
CAD21
171
E12
CVS1
181
B10
AD16
43
P01
CAD22
172
C12
CVS2
167
F12
AD17
42
N06
CAD23
174
A12
DEVSEL
49
R02
AD18
41
N03
CAD24
177
C11
FILTER0
105
T19
AD19
40
N02
CAD25
178
E11
FILTER1
106
R17
AD20
38
M05
CAD26
179
F11
FRAME
45
N05
AD21
37
M06
CAD27
188
F09
GND
6
E01
AD22
36
M03
CAD28
189
E09
GND
24
K01
AD23
35
M02
CAD29
191
B08
GND
39
N01
AD24
31
L03
CAD30
192
C08
GND
62
W06
AD25
30
L02
CAD31
194
E08
GND
114
P19
AD26
28
K06
CAUDIO
184
F10
GND
128
K19
AD27
27
K05
C/BE0
65
V07
GND
143
G19
AD28
26
K03
C/BE1
54
U05
GND
162
A15
AD29
25
K02
C/BE2
44
P02
GND
180
A10
AD30
23
J06
C/BE3
32
L06
GND
195
A07
AD31
22
J05
CBLOCK
153
E18
GNT
19
J01
ANALOGGND
83
U11
CC/BE0
137
J15
GRST
17
H02
ANALOGGND
90
R12
CC/BE1
149
G15
IDSEL
33
L05
ANALOGGND
97
R13
CC/BE2
163
C14
IRDY
46
P03
ANALOGVCC
85
R11
CC/BE3
176
B11
MFUNC0
3
F05
ANALOGVCC
93
U13
CCD1
125
L17
MFUNC1
4
G06
ANALOGVCC
98
U14
CCD2
187
C09
MFUNC2
7
F03
CAD0
126
L15
CCLK
158
C15
MFUNC3
8
F02
CAD1
129
K18
CCLKRUN
186
B09
MFUNC4
9
G05
CAD2
127
L14
CDEVSEL
157
A16
MFUNC5
10
F01
CAD3
131
K15
CFRAME
161
B15
MFUNC6
11
H06
CAD4
130
K17
CGNT
156
D19
MS_BS/
SD_DATA1/IRQ
117
N18
CAD5
133
J19
CINT
182
C10
MS_INS/SD_CD
115
M14
2–7
Table 2–3. CardBus PC Card Signal Names Sorted Alphabetically (Continued)
SIGNAL NAME
TERMINAL NUMBER
PDV
GHK
MS_RFU5/
SD_CMD
120
M17
MS_RFU7/
SD_CD/DATA3
121
MS_SCLK/
SD_CLK
MS_SDIO/
SD_DATA0
SIGNAL NAME
TERMINAL NUMBER
SIGNAL NAME
TERMINAL NUMBER
PDV
GHK
PDV
GHK
RSVD
202
C06
VCC
14
A05
M18
RSVD
197
C07
VCC
34
A08
119
M15
R0
91
W13
VCC
47
A13
118
N19
R1
92
V13
VCC
70
E19
NC
–
E05
SCL
2
E03
G01
84
P11
SDA
1
D01
VCC
VCC
123
NC
138
H19
NC
89
P12
SD_DATA2
122
M19
151
L19
NC
94
P13
SD_WP
116
N17
VCC
VCC
170
M01
NC
100
P14
SERR
52
T01
190
R01
NC
102
R14
SKT_SEL0
78
U10
VCC
VCC
203
W08
NC
104
W16
SKT_SEL1
79
R10
VCCCB
VCCCB
146
A11
175
G14
29
L01
58
W05
PAR
53
W04
SPKROUT
5
E02
PCLK
18
H01
STOP
50
P05
PC0
77
V10
SUSPEND
12
G03
VCCP
VCCP
PC1
76
W10
TPA0N
86
W12
VDPLL
107
P15
B05
PC2
75
P09
TPA0P
87
V12
VD0/VCCD1
205
PERR
51
R03
TPA1N
99
W15
VD1/VCCD0
206
E06
PHY_TEST_MA
112
P18
TPA1P
101
V15
VD2/VPPD1
207
C05
PRST
16
H03
TPBIAS0
88
U12
VD3/VPPD0
208
A04
2–8
REQ
20
J02
TPBIAS1
103
U15
VR_EN
15
H05
RI_OUT/PME
21
J03
TPB0N
81
W11
VR_PORT
13
G02
RSVD
196
B07
TPB0P
82
V11
VR_PORT
124
L18
RSVD
198
F07
TPB1N
95
W14
VSPLL
108
N14
RSVD
199
A06
TPB1P
96
V14
XI
109
R18
RSVD
201
E07
TRDY
48
P06
XO
110
R19
RSVD
200
B06
UM_PWR_CTRL
113
N15
Table 2–4. 16-Bit PC Card Signal Names Sorted Alphabetically
SIGNAL NAME
TERMINAL NUMBER
PDV
GHK
AD0
74
R09
AD1
73
AD2
72
AD3
SIGNAL NAME
TERMINAL NUMBER
SIGNAL NAME
TERMINAL NUMBER
PDV
GHK
PDV
GHK
A9
147
F19
D4
129
K18
U09
A10
139
H18
D5
131
K15
V09
A11
142
H15
D6
133
J19
71
W09
A12
163
C14
D7
135
J17
AD4
69
V08
A13
152
F14
D8
189
E09
AD5
68
U08
A14
154
F15
D9
192
C08
AD6
67
R08
A15
160
F13
D10
194
E08
AD7
66
W07
A16
158
C15
D11
127
L14
AD8
64
U07
A17
148
F18
D12
130
K17
AD9
63
P08
A18
150
F17
D13
132
K14
AD10
61
R07
A19
153
E18
D14
134
J18
AD11
60
V06
A20
155
E17
D15
136
J14
AD12
59
U06
A21
157
A16
FILTER0
105
T19
AD13
57
V05
A22
159
E14
FILTER1
106
R17
AD14
56
P07
A23
161
B15
FRAME
45
N05
AD15
55
R06
A24
164
B14
GND
6
E01
AD16
43
P01
A25
166
A14
GND
24
K01
AD17
42
N06
ANALOGGND
83
U11
GND
39
N01
AD18
41
N03
ANALOGGND
90
R12
GND
62
W06
AD19
40
N02
ANALOGGND
97
R13
GND
114
P19
AD20
38
M05
ANALOGVCC
85
R11
GND
128
K19
AD21
37
M06
ANALOGVCC
93
U13
GND
143
G19
AD22
36
M03
ANALOGVCC
98
U14
GND
162
A15
AD23
35
M02
BVD1(STSCHG/RI)
185
A09
GND
180
A10
AD24
31
L03
BVD2(SPKR)
184
F10
GND
195
A07
AD25
30
L02
C/BE0
65
V07
GNT
19
J01
AD26
28
K06
C/BE1
54
U05
GRST
17
H02
AD27
27
K05
C/BE2
44
P02
IDSEL
33
L05
AD28
26
K03
C/BE3
32
L06
INPACK
173
B12
AD29
25
K02
CD1
125
L17
IORD
144
G18
AD30
23
J06
CD2
187
C09
IOWR
145
G17
AD31
22
J05
CE1
137
J15
IRDY
46
P03
A0
179
F11
CE2
140
H17
MFUNC0
3
F05
A1
178
E11
CLK_48
204
F06
MFUNC1
4
G06
A2
177
C11
CNA
111
P17
MFUNC2
7
F03
A3
174
A12
CPS
80
P10
MFUNC3
8
F02
A4
172
C12
DEVSEL
49
R02
MFUNC4
9
G05
A5
171
E12
D0
188
F09
MFUNC5
10
F01
A6
168
C13
D1
191
B08
MFUNC6
11
H06
A7
165
E13
D2
193
F08
MS_BS/
SD_DATA1/IRQ
117
N18
A8
149
G15
D3
126
L15
MS_INS/SD_CD
115
M14
2–9
Table 2–4. 16-Bit PC Card Signal Names Sorted Alphabetically (Continued)
SIGNAL NAME
2–10
TERMINAL NUMBER
PDV
GHK
MS_RFU5/
SD_CMD
120
M17
MS_RFU7/
SD_CD/DATA3
121
MS_SCLK/
SD_CLK
MS_SDIO/
SD_DATA0
SIGNAL NAME
TERMINAL NUMBER
SIGNAL NAME
TERMINAL NUMBER
PDV
GHK
PDV
GHK
RSVD
200
B06
VCC
47
A13
M18
RSVD
202
C06
VCC
70
E19
119
M15
RSVD
197
C07
VCC
123
G01
118
N19
R0
91
W13
VCC
138
H19
NC
–
E05
R1
92
V13
L19
84
P11
SCL
2
E03
VCC
VCC
151
NC
170
M01
NC
89
P12
SDA
1
D01
190
R01
NC
94
P13
SD_DATA2
122
M19
VCC
VCC
203
W08
NC
100
P14
SD_WP
116
N17
146
A11
NC
102
R14
SERR
52
T01
VCCCB
VCCCB
175
G14
NC
104
W16
SKT_SEL0
78
U10
29
L01
OE
141
H14
SKT_SEL1
79
R10
VCCP
VCCP
58
W05
PAR
53
W04
SPKROUT
5
E02
VDPLL
107
P15
PCLK
18
H01
STOP
50
P05
VD0/VCCD1
205
B05
PC0
77
V10
SUSPEND
12
G03
VD1/VCCD0
206
E06
PC1
76
W10
TPA0N
86
W12
VD2/VPPD1
207
C05
PC2
75
P09
TPA0P
87
V12
VD3/VPPD0
208
A04
PERR
51
R03
TPA1N
99
W15
VR_EN
15
H05
PHY_TEST_MA
112
P18
TPA1P
101
V15
VR_PORT
13
G02
PRST
16
H03
TPBIAS0
88
U12
VR_PORT
124
L18
READY(IREQ)
182
C10
TPBIAS1
103
U15
VSPLL
108
N14
REG
176
B11
TPB0N
81
W11
VS1
181
B10
REQ
20
J02
TPB0P
82
V11
VS2
167
F12
RESET
169
B13
TPB1N
95
W14
WAIT
183
E10
RI_OUT/PME
21
J03
TPB1P
96
V14
WE
156
D19
RSVD
196
B07
TRDY
48
P06
WP(IOIS16)
186
B09
RSVD
198
F07
UM_PWR_CTRL
113
N14
XI
109
R18
RSVD
199
A06
14
A05
XO
110
R19
RSVD
201
E07
VCC
VCC
34
A08
The terminals are grouped in tables by functionality, such as PCI system function, power-supply function, etc. The
terminal numbers are also listed for convenient reference.
Table 2–5. Power Supply Terminals
TERMINAL
NUMBER
NAME
I/O
DESCRIPTION
PDV
GHK
GND
6, 24, 39, 62,
114, 128, 143,
162, 180, 195
E01, K01, N01,
W06, P19, K19,
G19, A15, A10,
A07
–
VCC
14, 34, 47, 70,
123, 138, 151,
170, 190, 203
G01, M01, R01,
W08, L19, H19,
E19, A13, A08,
A05
–
VCCCB
146, 175
G14, A11
–
Clamp voltage for PC CardBus interface. Matches card B signaling environment,
5 V or 3.3 V
VCCP
VR_EN
29, 58
L01, W05
–
Clamp voltage for PCI and miscellaneous I/O, 5 V or 3.3 V
15
H05
I
Internal voltage regulator enable. Active low
VR_PORT
13, 124
G02, L18
I/O
Device ground terminal
Power supply terminal for I/O and internal voltage regulator
1.8 V output from voltage regulator
Table 2–6. PC Card Power Switch Terminals
TERMINAL
NUMBER
NAME
PDV
GHK
206
205
208
207
E06
B05
A04
C05
VD1/VCCD0
VD0/VCCD1
VD3/VPPD0
VD2/VPPD1
I/O
O
DESCRIPTION
Logic controls to the TPS2211A or TPS2221 PC Card power interface
Table 2–7. PCI System Terminals
TERMINAL
NUMBER
NAME
I/O
DESCRIPTION
H02
I
Global reset. When the global reset is asserted, the GRST signal causes the PCI7410 device to place all
output buffers in a high-impedance state and reset all internal registers. When GRST is asserted, the device
is completely in its default state. GRST must be connected to POWER_OK.
H01
I
PCI bus clock. PCLK provides timing for all transactions on the PCI bus. All PCI signals are sampled at the
rising edge of PCLK.
I
PCI bus reset. When the PCI bus reset is asserted, PRST causes the PCI7410 device to place all output
buffers in a high-impedance state and reset internal registers. When PRST is asserted, the device is
completely nonfunctional. After PRST is deasserted, the PCI7410 device is in a default state.
When SUSPEND and PRST are asserted, the device is protected from PRST clearing the internal registers.
All outputs are placed in a high-impedance state, but the contents of the registers are preserved.
PDV
GHK
GRST
17
PCLK
18
PRST
16
H03
2–11
Table 2–8. PCI Address and Data Terminals
TERMINAL
NUMBER
NAME
PDV
GHK
AD31
AD30
AD29
AD28
AD27
AD26
AD25
AD24
AD23
AD22
AD21
AD20
AD19
AD18
AD17
AD16
AD15
AD14
AD13
AD12
AD11
AD10
AD9
AD8
AD7
AD6
AD5
AD4
AD3
AD2
AD1
AD0
22
23
25
26
27
28
30
31
35
36
37
38
40
41
42
43
55
56
57
59
60
61
63
64
66
67
68
69
71
72
73
74
J05
J06
K02
K03
K05
K06
L02
L03
M02
M03
M06
M05
N02
N03
N06
P01
R06
P07
V05
U06
V06
R07
P08
U07
W07
R08
U08
V08
W09
V09
U09
R09
C/BE3
C/BE2
C/BE1
C/BE0
32
44
54
65
L06
P02
U05
V07
PAR
2–12
53
W04
I/O
DESCRIPTION
I/O
PCI address/data bus. These signals make up the multiplexed PCI address and data bus on the primary
interface. During the address phase of a primary-bus PCI cycle, AD31–AD0 contain a 32-bit address or
other destination information. During the data phase, AD31–AD0 contain data.
I/O
PCI-bus commands and byte enables. These signals are multiplexed on the same PCI terminals. During
the address phase of a primary-bus PCI cycle, C/BE3–C/BE0 define the bus command. During the data
phase, this 4-bit bus is used as byte enables. The byte enables determine which byte paths of the full 32-bit
data bus carry meaningful data. C/BE0 applies to byte 0 (AD7–AD0), C/BE1 applies to byte 1 (AD15–AD8),
C/BE2 applies to byte 2 (AD23–AD16), and C/BE3 applies to byte 3 (AD31–AD24).
I/O
PCI-bus parity. In all PCI-bus read and write cycles, the PCI7410 device calculates even parity across the
AD31–AD0 and C/BE3–C/BE0 buses. As an initiator during PCI cycles, the PCI7410 device outputs this
parity indicator with a one-PCLK delay. As a target during PCI cycles, the PCI7410 device compares its
calculated parity to the parity indicator of the initiator. A compare error results in the assertion of a parity error
(PERR).
Table 2–9. PCI Interface Control Terminals
TERMINAL
NUMBER
I/O
DESCRIPTION
R02
I/O
PCI device select. The PCI7410 device asserts DEVSEL to claim a PCI cycle as the target device. As a PCI
initiator on the bus, the PCI7410 device monitors DEVSEL until a target responds. If no target responds before
timeout occurs, then the PCI7410 device terminates the cycle with an initiator abort.
45
N05
I/O
PCI cycle frame. FRAME is driven by the initiator of a bus cycle. FRAME is asserted to indicate that a bus
transaction is beginning, and data transfers continue while this signal is asserted. When FRAME is
deasserted, the PCI bus transaction is in the final data phase.
GNT
19
J01
I
PCI bus grant. GNT is driven by the PCI bus arbiter to grant the PCI7410 device access to the PCI bus after
the current data transaction has completed. GNT may or may not follow a PCI bus request, depending on the
PCI bus parking algorithm.
IDSEL
33
L05
I
Initialization device select. IDSEL selects the PCI7410 device during configuration space accesses. IDSEL
can be connected to one of the upper 24 PCI address lines on the PCI bus.
IRDY
46
P03
I/O
PCI initiator ready. IRDY indicates the ability of the PCI bus initiator to complete the current data phase of the
transaction. A data phase is completed on a rising edge of PCLK where both IRDY and TRDY are asserted.
Until IRDY and TRDY are both sampled asserted, wait states are inserted.
PERR
51
R03
I/O
PCI parity error indicator. PERR is driven by a PCI device to indicate that calculated parity does not match
PAR when PERR is enabled through bit 6 of the command register (PCI offset 04h, see Section 4.5).
REQ
20
J02
O
PCI bus request. REQ is asserted by the PCI7410 device to request access to the PCI bus as an initiator.
NAME
PDV
GHK
DEVSEL
49
FRAME
SERR
52
T01
O
PCI system error. SERR is an output that is pulsed from the PCI7410 device when enabled through bit 8 of
the command register (PCI offset 04h, see Section 4.5) indicating a system error has occurred. The PCI7410
device need not be the target of the PCI cycle to assert this signal. When SERR is enabled in the command
register, this signal also pulses, indicating that an address parity error has occurred on a CardBus interface.
STOP
50
P05
I/O
PCI cycle stop signal. STOP is driven by a PCI target to request the initiator to stop the current PCI bus
transaction. STOP is used for target disconnects and is commonly asserted by target devices that do not
support burst data transfers.
TRDY
48
P06
I/O
PCI target ready. TRDY indicates the ability of the primary bus target to complete the current data phase of
the transaction. A data phase is completed on a rising edge of PCLK when both IRDY and TRDY are asserted.
Until both IRDY and TRDY are asserted, wait states are inserted.
2–13
Table 2–10. Multifunction and Miscellaneous Terminals
TERMINAL
NUMBER
NAME
I/O
DESCRIPTION
PDV
GHK
CLK_48
204
F06
I
MFUNC0
3
F05
I/O
Multifunction terminal 0. See Section 4.37, Multifunction Routing Status Register, for
configuration details.
MFUNC1
4
G06
I/O
Multifunction terminal 1. See Section 4.37, Multifunction Routing Status Register, for
configuration details.
MFUNC2
7
F03
I/O
Multifunction terminal 2. See Section 4.37, Multifunction Routing Status Register, for
configuration details.
MFUNC3
8
F02
I/O
Multifunction terminal 3. See Section 4.37, Multifunction Routing Status Register, for
configuration details.
MFUNC4
9
G05
I/O
Multifunction terminal 4. See Section 4.37, Multifunction Routing Status Register, for
configuration details.
MFUNC5
10
F01
I/O
Multifunction terminal 5. See Section 4.37, Multifunction Routing Status Register, for
configuration details.
MFUNC6
11
H06
I/O
Multifunction terminal 6. See Section 4.37, Multifunction Routing Status Register, for
configuration details.
NC
—
84, 89, 94,
100, 102,
104
E05
P11, P12,
P13, P14,
R14, W16
PHY_TEST_MA
112
P18
I
PHY test pin. Not for customer use. It must be tied to ground.
RI_OUT/PME
21
J03
O
Ring indicate out and power management event output. This terminal provides an output
for ring-indicate or PME signals.
I/O
Serial clock. This terminal provides the serial clock signaling and is implemented as
open-drain. For normal operation (a ROM is implemented in the design), this terminal
must be pulled high to the ROM VDD with a 2.7-kΩ resistor. Otherwise, it must be pulled
low to ground with a 220-Ω resistor.
SCL
2–14
2
E03
48-MHz clock terminal
No connect. These terminals have no connection anywhere within the package. Terminal
E05 on the GHK package is used as a key to indicate the location of the A01 corner of
the BGA package.
Serial data. At GRST, the SDA signal is sampled to determine if a two-wire serial ROM
is present. If the serial ROM is detected, then this terminal provides the serial data
signaling.
SDA
1
D01
I/O
SKT_SEL0
SKT_SEL1
78
79
U10
R10
I/O
Socket select terminals. Depending on how these two terminals are configured, the
PCI7410 device configures PCI function 1 to support either Secure Digital, Memory Stick,
or Smart Card. See Section 3.2.5, Dedicated Socket (Function 1) Interface, for details.
This terminal is implemented as open-drain, and for normal operation (a ROM is
implemented in the design), this terminal must be pulled high to the ROM VDD with a
2.7-kΩ resistor. Otherwise, it must be pulled low to ground with a 220-Ω resistor.
SPKROUT
5
E02
O
Speaker output. SPKROUT is the output to the host system that can carry SPKR or
CAUDIO through the PCI7410 device from the PC Card interface. SPKROUT is a low
value (0) default. Card insertion or removal, or turning power on or off does not cause any
changes to the SPKROUT terminal.
SUSPEND
12
G03
I
Suspend. SUSPEND protects the internal registers from clearing when the GRST or
PRST signal is asserted. See Section 3.9.6, Suspend Mode, for details.
Table 2–11. 16-Bit PC Card Address and Data Terminals
TERMINAL
NUMBER
NAME
I/O
DESCRIPTION
PDV
GHK
A25
A24
A23
A22
A21
A20
A19
A18
A17
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
166
164
161
159
157
155
153
150
148
158
160
154
152
163
142
139
147
149
165
168
171
172
174
177
178
179
A14
B14
B15
E14
A16
E17
E18
F17
F18
C15
F13
F15
F14
C14
H15
H18
F19
G15
E13
C13
E12
C12
A12
C11
E11
F11
O
PC Card address. 16-bit PC Card address lines. A25 is the most significant bit.
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
136
134
132
130
127
194
192
189
135
133
131
129
126
193
191
188
J14
J18
K14
K17
L14
E08
C08
E09
J17
J19
K15
K18
L15
F08
B08
F09
I/O
PC Card data. 16-bit PC Card data lines. D15 is the most significant bit.
2–15
Table 2–12. 16-Bit PC Card Interface Control Terminals
TERMINAL
NUMBER
NAME
BVD1
(STSCHG/RI)
PDV
185
I/O
DESCRIPTION
GHK
A09
I
Battery voltage detect 1. BVD1 is generated by 16-bit memory PC Cards that include batteries. BVD1
is used with BVD2 as an indication of the condition of the batteries on a memory PC Card. Both BVD1
and BVD2 are high when the battery is good. When BVD2 is low and BVD1 is high, the battery is weak
and must be replaced. When BVD1 is low, the battery is no longer serviceable and the data in the
memory PC Card is lost. See Section 5.6, ExCA Card Status-Change Interrupt Configuration
Register, for enable bits. See Section 5.5, ExCA Card Status-Change Register, and Section 5.2,
ExCA Interface Status Register, for the status bits for this signal.
Status change. STSCHG is used to alert the system to a change in the READY, write protect, or
battery voltage dead condition of a 16-bit I/O PC Card.
Ring indicate. RI is used by 16-bit modem cards to indicate a ring detection.
BVD2
(SPKR)
184
F10
I
Battery voltage detect 2. BVD2 is generated by 16-bit memory PC Cards that include batteries. BVD2
is used with BVD1 as an indication of the condition of the batteries on a memory PC Card. Both BVD1
and BVD2 are high when the battery is good. When BVD2 is low and BVD1 is high, the battery is weak
and must be replaced. When BVD1 is low, the battery is no longer serviceable and the data in the
memory PC Card is lost. See Section 5.6, ExCA Card Status-Change Interrupt Configuration
Register, for enable bits. See Section 5.5, ExCA Card Status-Change Register, and Section 5.2,
ExCA Interface Status Register, for the status bits for this signal.
Speaker. SPKR is an optional binary audio signal available only when the card and socket have been
configured for the 16-bit I/O interface. The audio signals from cards A and B are combined by the
PCI7410 device and are output on SPKROUT.
CD1
CD2
125
187
L17
C09
I
Card detect 1 and card detect 2. CD1 and CD2 are internally connected to ground on the PC Card.
When a PC Card is inserted into a socket, CD1 and CD2 are pulled low. For signal status, see
Section 5.2, ExCA Interface Status Register.
CE1
CE2
137
140
J15
H17
O
Card enable 1 and card enable 2. CE1 and CE2 enable even- and odd-numbered address bytes. CE1
enables even-numbered address bytes, and CE2 enables odd-numbered address bytes.
INPACK
173
B12
I
Input acknowledge. INPACK is asserted by the PC Card when it can respond to an I/O read cycle
at the current address.
IORD
144
G18
O
I/O read. IORD is asserted by the PCI7410 device to enable 16-bit I/O PC Card data output during
host I/O read cycles.
IOWR
145
G17
O
I/O write. IOWR is driven low by the PCI7410 device to strobe write data into 16-bit I/O PC Cards
during host I/O write cycles.
OE
141
H14
O
Output enable. OE is driven low by the PCI7410 device to enable 16-bit memory PC Card data output
during host memory read cycles.
READY
(IREQ)
2–16
182
C10
I
Ready. The ready function is provided by READY when the 16-bit PC Card and the host socket are
configured for the memory-only interface. READY is driven low by 16-bit memory PC Cards to
indicate that the memory card circuits are busy processing a previous write command. READY is
driven high when the 16-bit memory PC Card is ready to accept a new data transfer command.
Interrupt request. IREQ is asserted by a 16-bit I/O PC Card to indicate to the host that a device on
the 16-bit I/O PC Card requires service by the host software. IREQ is high (deasserted) when no
interrupt is requested.
REG
176
B11
O
Attribute memory select. REG remains high for all common memory accesses. When REG is
asserted, access is limited to attribute memory (OE or WE active) and to the I/O space (IORD or
IOWR active). Attribute memory is a separately accessed section of card memory and is generally
used to record card capacity and other configuration and attribute information.
RESET
169
B13
O
PC Card reset. RESET forces a hard reset to a 16-bit PC Card.
Table 2–12. 16-Bit PC Card Interface Control Terminals (Continued)
TERMINAL
NUMBER
NAME
I/O
DESCRIPTION
B10
F12
I/O
Voltage sense 1 and voltage sense 2. VS1 and VS2, when used in conjunction with each other, determine
the operating voltage of the PC Card.
183
E10
I
Bus cycle wait. WAIT is driven by a 16-bit PC Card to extend the completion of the memory or I/O cycle in
progress.
156
D19
O
Write enable. WE is used to strobe memory write data into 16-bit memory PC Cards. WE is also used for
memory PC Cards that employ programmable memory technologies.
PDV
GHK
VS1
VS2
181
167
WAIT
WE
WP
(IOIS16)
Write protect. WP applies to 16-bit memory PC Cards. WP reflects the status of the write-protect switch on
16-bit memory PC Cards. For 16-bit I/O cards, WP is used for the 16-bit port (IOIS16) function.
186
B09
I
I/O is 16 bits. IOIS16 applies to 16-bit I/O PC Cards. IOIS16 is asserted by the 16-bit PC Card when the
address on the bus corresponds to an address to which the 16-bit PC Card responds, and the I/O port that
is addressed is capable of 16-bit accesses.
Table 2–13. CardBus PC Card Interface System Terminals
TERMINAL
NUMBER
NAME
PDV
I/O
DESCRIPTION
GHK
CCLK
158
C15
O
CardBus clock. CCLK provides synchronous timing for all transactions on the CardBus interface. All
signals except CRST, CCLKRUN, CINT, CSTSCHG, CAUDIO, CCD2, CCD1, CVS2, and CVS1 are
sampled on the rising edge of CCLK, and all timing parameters are defined with the rising edge of this
signal. CCLK operates at the PCI bus clock frequency, but it can be stopped in the low state or slowed
down for power savings.
CCLKRUN
186
B09
I/O
CardBus clock run. CCLKRUN is used by a CardBus PC Card to request an increase in the CCLK
frequency, and by the PCI7410 device to indicate that the CCLK frequency is going to be decreased.
O
CardBus reset. CRST brings CardBus PC Card-specific registers, sequencers, and signals to a known
state. When CRST is asserted, all CardBus PC Card signals are placed in a high-impedance state, and
the PCI7410 device drives these signals to a valid logic level. Assertion can be asynchronous to CCLK,
but deassertion must be synchronous to CCLK.
CRST
169
B13
2–17
Table 2–14. CardBus PC Card Address and Data Terminals
TERMINAL
NUMBER
NAME
PDV
GHK
CAD31
CAD30
CAD29
CAD28
CAD27
CAD26
CAD25
CAD24
CAD23
CAD22
CAD21
CAD20
CAD19
CAD18
CAD17
CAD16
CAD15
CAD14
CAD13
CAD12
CAD11
CAD10
CAD9
CAD8
CAD7
CAD6
CAD5
CAD4
CAD3
CAD2
CAD1
CAD0
194
192
191
189
188
179
178
177
174
172
171
168
166
165
164
148
145
147
144
142
141
140
139
136
135
132
133
130
131
127
129
126
E08
C08
B08
E09
F09
F11
E11
C11
A12
C12
E12
C13
A14
E13
B14
F18
G17
F19
G18
H15
H14
H17
H18
J14
J17
K14
J19
K17
K15
L14
K18
L15
CC/BE3
CC/BE2
CC/BE1
CC/BE0
176
163
149
137
B11
C14
G15
J15
CPAR
2–18
152
F14
I/O
DESCRIPTION
I/O
CardBus address and data. These signals make up the multiplexed CardBus address and data bus on
the CardBus interface. During the address phase of a CardBus cycle, CAD31–CAD0 contain a 32-bit
address. During the data phase of a CardBus cycle, CAD31–CAD0 contain data. CAD31 is the most
significant bit.
I/O
CardBus bus commands and byte enables. CC/BE3–CC/BE0 are multiplexed on the same CardBus
terminals. During the address phase of a CardBus cycle, CC/BE3–CC/BE0 define the bus command.
During the data phase, this 4-bit bus is used as byte enables. The byte enables determine which byte paths
of the full 32-bit data bus carry meaningful data. CC/BE0 applies to byte 0 (CAD7–CAD0), CC/BE1 applies
to byte 1 (CAD15–CAD8), CC/BE2 applies to byte 2 (CAD23–CAD16), and CC/BE3 applies to byte 3
(CAD31–CAD24).
I/O
CardBus parity. In all CardBus read and write cycles, the PCI7410 device calculates even parity across
the CAD and CC/BE buses. As an initiator during CardBus cycles, the PCI7410 device outputs CPAR with
a one-CCLK delay. As a target during CardBus cycles, the PCI7410 device compares its calculated parity
to the parity indicator of the initiator; a compare error results in a parity error assertion.
Table 2–15. CardBus PC Card Interface Control Terminals
TERMINAL
NUMBER
I/O
DESCRIPTION
F10
I
CardBus audio. CAUDIO is a digital input signal from a PC Card to the system speaker. The PCI7410
device supports the binary audio mode and outputs a binary signal from the card to SPKROUT.
153
E18
I/O
CCD1
CCD2
125
187
L17
C09
I
CardBus detect 1 and CardBus detect 2. CCD1 and CCD2 are used in conjunction with CVS1 and
CVS2 to identify card insertion and interrogate cards to determine the operating voltage and card type.
CDEVSEL
157
A16
I/O
CardBus device select. The PCI7410 device asserts CDEVSEL to claim a CardBus cycle as the target
device. As a CardBus initiator on the bus, the PCI7410 device monitors CDEVSEL until a target
responds. If no target responds before timeout occurs, then the PCI7410 device terminates the cycle
with an initiator abort.
CFRAME
161
B15
I/O
CardBus cycle frame. CFRAME is driven by the initiator of a CardBus bus cycle. CFRAME is asserted
to indicate that a bus transaction is beginning, and data transfers continue while this signal is asserted.
When CFRAME is deasserted, the CardBus bus transaction is in the final data phase.
CGNT
156
D19
O
CardBus bus grant. CGNT is driven by the PCI7410 device to grant a CardBus PC Card access to the
CardBus bus after the current data transaction has been completed.
CINT
182
C10
I
CardBus interrupt. CINT is asserted low by a CardBus PC Card to request interrupt servicing from the
host.
CIRDY
160
F13
I/O
CardBus initiator ready. CIRDY indicates the ability of the CardBus initiator to complete the current data
phase of the transaction. A data phase is completed on a rising edge of CCLK when both CIRDY and
CTRDY are asserted. Until CIRDY and CTRDY are both sampled asserted, wait states are inserted.
CPERR
154
F15
I/O
CardBus parity error. CPERR reports parity errors during CardBus transactions, except during special
cycles. It is driven low by a target two clocks following the data cycle during which a parity error is
detected.
CREQ
173
B12
I
CardBus request. CREQ indicates to the arbiter that the CardBus PC Card desires use of the CardBus
bus as an initiator.
NAME
PDV
GHK
CAUDIO
184
CBLOCK
CardBus lock. CBLOCK is used to gain exclusive access to a target.
CSERR
183
E10
I
CardBus system error. CSERR reports address parity errors and other system errors that could lead
to catastrophic results. CSERR is driven by the card synchronous to CCLK, but deasserted by a weak
pullup; deassertion may take several CCLK periods. The PCI7410 device can report CSERR to the
system by assertion of SERR on the PCI interface.
CSTOP
155
E17
I/O
CardBus stop. CSTOP is driven by a CardBus target to request the initiator to stop the current CardBus
transaction. CSTOP is used for target disconnects, and is commonly asserted by target devices that
do not support burst data transfers.
CSTSCHG
185
A09
I
CardBus status change. CSTSCHG alerts the system to a change in the card status, and is used as
a wake-up mechanism.
CTRDY
159
E14
I/O
CardBus target ready. CTRDY indicates the ability of the CardBus target to complete the current data
phase of the transaction. A data phase is completed on a rising edge of CCLK, when both CIRDY and
CTRDY are asserted; until this time, wait states are inserted.
CVS1
CVS2
181
167
B10
F12
I/O
CardBus voltage sense 1 and CardBus voltage sense 2. CVS1 and CVS2 are used in conjunction with
CCD1 and CCD2 to identify card insertion and interrogate cards to determine the operating voltage and
card type.
2–19
Table 2–16. IEEE 1394 Physical Layer Terminals
TERMINAL
NUMBER
I/O
DESCRIPTION
P17
I/O
Cable not active. This terminal is asserted high when there are no ports receiving incoming bias voltage.
If it is not used, then this terminal must be strapped either to GND through a resistor.
80
P10
I
Cable power status input. This terminal is normally connected to cable power through a 400-kΩ resistor.
This circuit drives an internal comparator that is used to detect the presence of cable power. If CPS is
not used to detect cable power, then this terminal must be tied to ground.
FILTER0
FILTER1
105
106
T19
R17
I/O
PLL filter terminals. These terminals are connected to an external capacitance to form a lag-lead filter
required for stable operation of the internal frequency multiplier PLL running off of the crystal oscillator.
A 0.1-µF ±10% capacitor is the only external component required to complete this filter.
PC0
PC1
PC2
77
76
75
V10
W10
P09
I
Power class programming inputs. On hardware reset, these inputs set the default value of the power
class indicated during self-ID. Programming is done by tying these terminals high or low.
R0
R1
91
92
W13
V13
–
Current-setting resistor terminals. These terminals are connected to an external resistance to set the
internal operating currents and cable driver output currents. A resistance of 6.34 kΩ ±1% is required
to meet the IEEE Std 1394-1995 output voltage limits.
TPA0P
TPA0N
87
86
V12
W12
I/O
TPA1P
TPA1N
101
99
V15
W15
I/O
TPBIAS0
TPBIAS1
88
103
U12
U15
I/O
TPB0P
TPB0N
82
81
V11
W11
I/O
TPB1P
TPB1N
96
95
V14
W14
I/O
NAME
PDV
GHK
CNA
111
CPS
XI
XO
109
110
R18
R19
Twisted-pair cable A differential signal terminals. Board trace lengths from each pair of positive and
negative differential signal pins must be matched and as short as possible to the external load resistors
and to the cable connector.
Twisted-pair bias output. This provides the 1.86-V nominal bias voltage needed for proper operation
of the twisted-pair cable drivers and receivers and for signaling to the remote nodes that there is an
active cable connection. Each of these pins must be decoupled with a 1.0-µF capacitor to ground.
Twisted-pair cable B differential signal terminals. Board trace lengths from each pair of positive and
negative differential signal pins must be matched and as short as possible to the external load resistors
and to the cable connector.
Crystal oscillator inputs. These pins connect to a 24.576-MHz parallel resonant fundamental mode
crystal. The optimum values for the external shunt capacitors are dependent on the specifications of
the crystal used (see Section 3.10.2, Crystal Selection). Terminal 5 has an internal 10-kΩ (nominal
value) pulldown resistor. An external clock input can be connected to the XI terminal. When using an
external clock input, the XO terminal must be left unconnected. Refer to Section 3.10.2 for the operating
characteristics of the XI terminal.
–
Table 2–17. Power Supply Terminals
TERMINAL
NUMBER
NAME
PDV
GHK
ANALOGGND
83
90
97
U11
R12
R13
ANALOGVCC
85
93
98
R11
U13
U14
I/O
DESCRIPTION
–
Analog circuit ground terminals.
–
Analog circuit power terminals. A parallel combination of high frequency decoupling capacitors near
each terminal is suggested, such as 0.1 µF and 0.001 µF. Lower frequency 10-µF filtering capacitors
are also recommended. These supply terminals are separated from VDPLL and VSPLL internal to
the device to provide noise isolation. They must be tied at a low-impedance point on the circuit board.
VDPLL
107
P15
–
PLL circuit power terminals. A parallel combination of high frequency decoupling capacitors near the
terminal is suggested, such as 0.1 µF and 0.001 µF. Lower frequency 10-µF filtering capacitors are
also recommended. This supply terminal is separated from AVDx internal to the device to provide
noise isolation. It must be tied at a low-impedance point on the circuit board.
VSPLL
108
N14
–
PLL circuit ground terminals. This terminal must be tied to the low-impedance circuit board ground
plane.
2–20
UltraMedia defines additional functionality for the CardBus/PC Card terminals. Table 2–18 provides the signal
descriptions for the dedicated socket signals.
Table 2–18. UltraMedia Dedicated Socket Terminals
TERMINAL
NUMBER
NAME
I/O
DESCRIPTION
PDV
GHK
MS_BS/
SD_DATA1/IRQ
117
N18
O
I/O
Memory Stick bus state. This signal provides Memory Stick bus state information.
SD flash data 1. This signal provides the SD data path in accordance with the SD Memory
Card Specifications.
MS_INS/
SD_CD
115
M14
I/O
Signals a memory stick or SD card insertion
SD flash card detection
MS_RFU5/
120
MS_RFU7/
119
I/O
SD flash command. This signal provides the SD command in accordance with the SD
Memory Card Specifications.
I
Memory Stick reserved. This terminal is in a high-impedance state when an UltraMedia
Memory Stick card has been inserted.
I/O
SD flash card detection/data 3. This signal provides the SD data path in accordance with
the SD Memory Card Specifications.
O
Memory Stick clock. This output provides the MS clock, which operates at 16 MHz.
SD flash clock. This output provides the MMC/SD clock, which operates at 16 MHz.
I/O
Memory Stick serial data I/O. This signal provides Memory Stick data input/output.
I/O
SD flash data 0. This signal provides the MMC_SD data path in accordance with the SD
Memory Card Specifications.
M18
SD_CD/DATA3
MS_SCLK/
SD_CLK
Memory Stick reserved. This terminal is in a high-impedance state when an UltraMedia
Memory Stick card has been inserted.
M17
SD_CMD
121
I
M15
MS_SDIO/
118
N19
196, 198,
199, 201,
200, 202,
197
B07, F07,
A06, E07,
B06, C06,
C07
I/O
Reserved for Smart Card use
SD_DATA2
122
M19
I/O
SD flash data 2. This signal provides the SD data path and CD in accordance with the SD
Memory Card Specifications.
SD_WP
116
N17
I
SD card write protect signal
UM_PWR_CTRL
113
N15
O
UltraMedia card power control
SD_DATA0
RSVD
2–21
2–22
3 Feature/Protocol Descriptions
The following sections give an overview of the PCI7410 device. Figure 3–1 shows the connections to the PCI7410
device. The PCI interface includes all address/data and control signals for PCI protocol. The interrupt interface
includes terminals for parallel PCI, parallel ISA, and serialized PCI and ISA signaling.
CPU
Graphics
Controller
AGP
North
Bridge
Memory
South
Bridge
PCI Bus
Power
Switch
SD/MS
EEPROM
PCI7410
16
68
PC Card
Power
Switch
1394
Socket
Figure 3–1. PCI7410 System Block Diagram
3.1 Power Supply Sequencing
The PCI7410 device contains 3.3-V I/O buffers with 5-V tolerance requiring a core power supply and clamp voltages.
The core power supply is always 1.8 V. The clamp voltages can be either 3.3 V or 5 V, depending on the interface.
The following power-up and power-down sequences are recommended.
The power-up sequence is:
1. Apply 3.3-V power to VCC.
3–1
2. Assert GRST to the device to disable the outputs during power up. Output drivers must be powered up in
the high-impedance state to prevent high current levels through the clamp diodes to the 5-V supply.
3. Apply the clamp voltage.
The power-down sequence is:
1. Assert GRST to switch the outputs to the high-impedance state.
2. Remove the clamp voltage.
3. Remove the 3.3-V power from VCC.
3.2 Summary of UltraMedia Cards
3.2.1
SmartMedia
Formerly called solid-state floppy-disk card (SSFDC), SmartMedia cards are about 1/3 the area of a standard PC
Card and only 0,76 mm in thickness. The specifications for SmartMedia cards are governed by the SSFDC Forum.
There are two basic types of SmartMedia cards, flash memory cards and mask ROM cards. The majority of
SmartMedia cards use an embedded NAND-type flash memory and are based on the package equals card concept.
This allows the cards to be very thin, and does not require a controller to be included on the SmartMedia card.
Almost all SmartMedia cards are 3.3-V cards, but there are also 5-V versions of the 1-, 2-, and 4-Mbyte
flash-memory-based cards. Additionally, all SmartMedia cards have a 22-terminal, 8-bit interface. The recommended
logical format of SmartMedia cards is based on the DOS/FAT format.
SmartMedia cards are currently used in many types of consumer electronic devices and can even be incorporated
in postcards that can then be accessed by a special reader. The most popular applications are in digital cameras and
portable music players. The two primary methods of interfacing SmartMedia cards to current systems are through
a floppy disk adapter or PCMCIA adapter.
3.2.2
MultiMediaCard (MMC)
The MultiMediaCard is a flash-memory card about the size of a postage stamp and 1,4 mm in thickness. The
specification for MMC is governed by the MultiMediaCard Association (MMCA). The interface for MMC cards is based
on a 7-terminal serial bus. The MultiMediaCard system specification defines a communication protocol for MMC
cards, referred to as MultiMediaCard mode. In addition, all MMC cards work in the alternate SPI mode. The SPI mode
allows a microcontroller to interface directly to the MMC card, but at the cost of slower performance.
The voltage range for communication with MMC cards is 2.0 to 3.6 V, and the memory-access voltage range is a
card-specific subrange of the communication voltage range. Like SmartMedia cards, MMC cards can be read-only
or read/write; however, MMC cards can also have I/O functionality.
MMC cards are designed to be used in either a stand-alone implementation or in a system with other MMC cards.
When in the MultiMediaCard mode, the bus protocol can address cards with up to 64K of memory, and up to 30 cards
on a single physical bus. However, the maximum data rate is only available with up to 10 MMC cards on the bus. In
order to accommodate such a wide variety of system implementations, the MMC clock rate can be varied from 0 to
20 MHz. UltraMedia supports one MMC card per UltraMedia socket.
MMC cards, like SmartMedia cards, are also used in many types of consumer electronic devices. Because of their
small size, they are primarily used in portable music players and phones.
3.2.3
Secure Digital (SD)
SD cards are the same size as MMC cards, except for the thickness, which at 2,1 mm is slightly thicker than an MMC
card. SD cards are based upon MMC cards, with the addition of two terminals. The use of these two terminals and
a reserved terminal on MMC cards allows the data bus on SD cards to be up to 4 bits wide instead of the 1-bit width
of the MMC data bus. SD cards can communicate in either SD mode or SPI mode.
3–2
The voltage range for basic communication with SD cards is 2.0 to 3.6 V, and the voltage range for other commands
and memory access is 2.7 to 3.6 V. SD cards can be read-only or read/write.
SD is essentially a superset of MMC, in that MMC cards work in SD systems, but SD cards do not work in current
MMC systems. Unlike MMC, each SD card in a system must have a dedicated bus. One of the primary benefits of
SD cards is the added security that they provide. SD cards comply with the highest security of SDMI, have built-in
write-protect features, and include a mechanical write-protect switch.
SD cards are used in many of the same devices as MMC cards. The additional security features of the SD cards also
allow their use in more-secure applications or in devices where content protection is essential.
3.2.4
Memory Stick
Memory Stick cards are about the size of a stick of gum and are 2,8 mm thick. Developed by Sony, Memory Stick
cards have a 10-terminal interface of which three terminals are used for serial communication, two terminals apply
power, two terminals are ground, one terminal is for insertion detection, and two terminals are reserved for future use.
Each card also includes an erasure-prevention switch to protect data stored on the card.
The voltage range for Memory Stick cards is 2.7 to 3.6 V, and the clock speed can be up to 20 MHz. Memory Stick
cards use the FAT file system to allow for easy communication with PCs.
There are two types of Memory Stick cards, the standard Memory Stick and the MagicGate Memory Stick. MagicGate
technology provides security to Memory Stick cards so that they can be used to store and protect copyrighted data.
Memory Stick cards are primarily used to store still images, moving images, voice and music. As such, they are used
in a variety of devices, including portable music players, digital cameras, and digital picture frames.
3.2.5
Dedicated Socket (Function 1) Interface
Dedicated socket (function 1) terminals can be configured to use one of the two interfaces: Secure Digital (SD) or
Memory Stick (MS). To use the SD or MS interface, the TPS2020 power switch is recommended. There are two socket
select terminals (SKT_SEL1 and SKT_SEL2) in the PCI7410 device, depending on how these two terminals are
configured, the PCI7410 device configures the dedicated socket (function 1) to support either the SD or MS interface.
The SKT_SEL1 and SKT_SEL0 terminal configurations are:
SKT_SEL1
SKT_SEL0
INTERFACE SELECTED
0
0
Reserved
0
1
SD/MMC
1
0
Memory Stick
1
1
None (test mode)
Use a pullup and/or pulldown resistor combination to configure SKT_SEL1 and SKT_SEL0 to select one of the three
interfaces.
3.3 I/O Characteristics
The PCI7410 device meets the ac specifications of the PC Card Standard (release 8.0) and PCI Local Bus
Specification. Figure 3–2 shows a 3-state bidirectional buffer. Section 12.2, Recommended Operating Conditions,
provides the electrical characteristics of the inputs and outputs.
3–3
VCCP
Tied for Open Drain
OE
Pad
Figure 3–2. 3-State Bidirectional Buffer
3.4 Clamping Voltages
The clamping voltages are set to match whatever external environment the PCI7410 device is interfaced with: 3.3 V
or 5 V. The I/O sites can be pulled through a clamping diode to a voltage rail that protects the core from external
signals. The core power supply is 1.8 V and is independent of the clamping voltages. For example, PCI signaling can
be either 3.3 V or 5 V, and the PCI7410 device must reliably accommodate both voltage levels. This is accomplished
by using a 3.3-V I/O buffer that is 5-V tolerant, with the applicable clamping voltage applied. If a system designer
desires a 5-V PCI bus, then VCCP can be connected to a 5-V power supply.
3.5 Peripheral Component Interconnect (PCI) Interface
The PCI7410 device is fully compliant with the PCI Local Bus Specification. The PCI7410 device provides all required
signals for PCI master or slave operation, and may operate in either a 5-V or 3.3-V signaling environment by
connecting the VCCP terminals to the desired voltage level. In addition to the mandatory PCI signals, the PCI7410
device provides the optional interrupt signals INTA, INTB, and INTC for functions 0, 1, and 2, respectively.
3.5.1
1394 PCI Bus Master
As a bus master, the 1394 function of the PCI7410 device supports the memory commands specified in Table 3–1
below. The PCI master supports the memory read, memory read line, and memory read multiple commands. The
read command usage for read transactions of greater than two data phases are determined by the selection in bits
9–8 (MR_ENHANCE field) of the PCI miscellaneous configuration register (refer to Section 7.23 for details). For read
transactions of one or two data phases, a memory read command is used.
Table 3–1. PCI Bus Master Command Support
PCI
Memory read
3.5.2
COMMAND
C/BE3–C/BE0
OHCI MASTER FUNCTION
0110
DMA read from memory
Memory write
0111
DMA write to memory
Memory read multiple
1100
DMA read from memory
Memory read line
1110
DMA read from memory
Memory write and invalidate
1111
DMA write to memory
PCI Bus Lock (LOCK)
The bus-locking protocol defined in the PCI Local Bus Specification is not highly recommended, but is provided on
the PCI7410 device as an additional compatibility feature. The PCI LOCK signal can be routed to the MFUNC4
terminal by setting the appropriate values in bits 19–16 of the multifunction routing status register. See Section 4.37,
Multifunction Routing Status Register, for details. Note that the use of LOCK is only supported by PCI-to-CardBus
bridges in the downstream direction (away from the processor).
PCI LOCK indicates an atomic operation that may require multiple transactions to complete. When LOCK is asserted,
nonexclusive transactions can proceed to an address that is not currently locked. A grant to start a transaction on
the PCI bus does not assure control of LOCK; control of LOCK is obtained under its own protocol. It is possible for
3–4
different initiators to use the PCI bus while a single master retains ownership of LOCK. Note that the CardBus signal
for this protocol is CBLOCK to avoid confusion with the bus clock.
An agent may need to do an exclusive operation because a critical access to memory might be broken into several
transactions, but the master wants exclusive rights to a region of memory. The granularity of the lock is defined by
PCI to be 16 bytes, aligned. The LOCK protocol defined by the PCI Local Bus Specification allows a resource lock
without interfering with nonexclusive real-time data transfer, such as video.
The PCI bus arbiter may be designed to support only complete bus locks using the LOCK protocol. In this scenario,
the arbiter does not grant the bus to any other agent (other than the LOCK master) while LOCK is asserted. A
complete bus lock may have a significant impact on the performance of the video. The arbiter that supports complete
bus LOCK must grant the bus to the cache to perform a writeback due to a snoop to a modified line when a locked
operation is in progress.
The PCI7410 device supports all LOCK protocols associated with PCI-to-PCI bridges, as also defined for
PCI-to-CardBus bridges. This includes disabling write posting while a locked operation is in progress, which can solve
a potential deadlock when using devices such as PCI-to-PCI bridges. The potential deadlock can occur if a CardBus
target supports delayed transactions and blocks access to the target until it completes a delayed read. This target
characteristic is prohibited by the PCI Local Bus Specification, and the issue is resolved by the PCI master using
LOCK.
3.5.3
Serial EEPROM I2C Bus
The PCI7410 device offers many choices for modes of operation, and these choices are selected by programming
several configuration registers. For system board applications, these registers are normally programmed through the
BIOS routine. For add-in card and docking-station/port-replicator applications, the PCI7410 device provides a
two-wire inter-integrated circuit (IIC or I2C) serial bus for use with an external serial EEPROM.
The PCI7410 device is always the bus master, and the EEPROM is always the slave. Either device can drive the bus
low, but neither device drives the bus high. The high level is achieved through the use of pullup resistors on the SCL
and SDA signal lines. The PCI7410 device is always the source of the clock signal, SCL.
System designers who wish to load register values with a serial EEPROM must use a pullup resistor on the SCL
terminal. If the PCI7410 device detects a logic-high level on the SCL terminal at the end of GRST, then it initiates
incremental reads from the external EEPROM. Any size serial EEPROM up to the I2C limit of 16 Kbits can be used,
but only the first 67 bytes (from offset 00h to offset 42h) are required to configure the PCI7410 device. Figure 3–3
shows a 2-Kbit serial EEPROM application.
In addition to loading configuration data from an EEPROM, the PCI7410 I2C bus can be used to read and write from
other I2C serial devices. A system designer can control the I2C bus, using the PCI7410 device as bus master, by
reading and writing PCI configuration registers. Setting bit 3 (SBDETECT) in the serial bus control/status register (PCI
offset B3h, see Section 4.51) causes the PCI7410 device to route the SDA and SCL signals to the SDA and SCL
terminals, respectively. The read/write data, slave address, and byte addresses are manipulated by accessing the
serial bus data, serial bus index, and serial bus slave address registers (PCI offsets B0h, B1h, and B2h; see Sections
4.48, 4.49, and 4.50, respectively).
EEPROM interface status information is communicated through the serial bus control and status register (PCI offset
B3h, see Section 4.51). Bit 2 (EEDETECT) in this register indicates whether or not the PCI7410 serial ROM circuitry
detects the pullup resistor on SCL. Any undefined condition, such as a missing acknowledge, results in bit 1
(DATAERR) being set. Bit 0 (EEBUSY) is set while the subsystem ID register is loading (serial ROM interface is busy).
The subsystem vendor ID for functions 2 and 3 is also loaded through EEPROM. The EEPROM load data goes to
all four functions from the serial EEPROM loader.
3–5
VCC
Serial
ROM
A0
A1
SCL
SCL
A2
SDA
SDA
PCI7410
Figure 3–3. Serial ROM Application
3.5.4
Loading Subsystem Identification
The subsystem vendor ID register (PCI offset 40h, see Section 4.27) and subsystem ID register (PCI offset 42h, see
Section 4.28) make up a doubleword of PCI configuration space for function 0. This doubleword register is used for
system and option card (mobile dock) identification purposes and is required by some operating systems.
Implementation of this unique identifier register is a PC 99/PC 2001 requirement.
The PCI7410 device offers two mechanisms to load a read-only value into the subsystem registers. The first
mechanism relies upon the system BIOS providing the subsystem ID value. The default access mode to the
subsystem registers is read-only, but can be made read/write by setting bit 5 (SUBSYSRW) in the system control
register (PCI offset 80h, see Section 4.30). Once this bit is set, the BIOS can write a subsystem identification value
into the registers at PCI offset 40h. The BIOS must clear the SUBSYSRW bit such that the subsystem vendor ID
register and subsystem ID register is limited to read-only access. This approach saves the added cost of
implementing the serial electrically erasable programmable ROM (EEPROM).
In some conditions, such as in a docking environment, the subsystem vendor ID register and subsystem ID register
must be loaded with a unique identifier via a serial EEPROM. The PCI7410 device loads the data from the serial
EEPROM after a reset of the primary bus. Note that the SUSPEND input gates the PCI reset from the entire PCI7410
core, including the serial-bus state machine (see Section 3.9.6, Suspend Mode, for details on using SUSPEND).
The PCI7410 device provides a two-line serial-bus host controller that can interface to a serial EEPROM. See
Section 3.7, Serial EEPROM Interface, for details on the two-wire serial-bus controller and applications.
3.5.4.1 Function 2 Subsystem Identification
The subsystem identification register is used for system and option card identification purposes. This register can
be initialized from the serial EEPROM or programmed via the subsystem access register at offset F8h in the PCI
configuration space (see Section 7.25, Subsystem Access Register). See Table 7–22 for a complete description of
the register contents.
Write access to the subsystem access register updates the subsystem identification registers identically to
OHCI-Lynx. The system ID value written to this register may also be read back from this register. See Table 7–22
for a complete description of the register contents.
3.5.4.2 Function 3 Subsystem Identification
The subsystem identification register is used for system and option card identification purposes. This register can
be initialized from the serial EEPROM or programmed via the subsystem access register at offset F8h in the PCI
3–6
configuration space (see Section 11.25, Subsystem Access Register). See Table 11–9 for a complete description of
the register contents.
3.6 PC Card Applications
The PCI7410 device supports all the PC Card features and applications as described below.
•
•
•
•
•
•
3.6.1
Card insertion/removal and recognition per the PC Card Standard (release 8.0)
Zoomed video support
Speaker and audio applications
LED socket activity indicators
PC Card controller programming model
CardBus socket registers
PC Card Insertion/Removal and Recognition
The PC Card Standard (release 8.0) addresses the card-detection and recognition process through an interrogation
procedure that the socket must initiate on card insertion into a cold, nonpowered socket. Through this interrogation,
card voltage requirements and interface (16-bit versus CardBus) are determined.
The scheme uses the card-detect and voltage-sense signals. The configuration of these four terminals identifies the
card type and voltage requirements of the PC Card interface.
3.6.2
Low Voltage CardBus Card Detection
The card detection logic of the PCI7410 device includes the detection of Cardbus cards with VCC = 3.3 V and
VPP = 1.8 V. The reporting of the 1.8-V CardBus card (VCC = 3.3 V, VPP = 1.8 V) is reported through the socket present
state register as follows based on bit 10 (12V_SW_SEL) in the general control register (PCI offset 86h, see Section
4.32):
•
If the 12V_SW_SEL bit is 0 (TPS2221 is used), then the 1.8-V CardBus card causes the 3VCARD bit in the
socket present state register to be set.
•
If the 12V_SW_SEL bit is 1 (TPS2211A is used), then the 1.8-V CardBus card causes the XVCARD bit in
the socket present state register to be set.
3.6.3
Card Detection in a UltraMedia System
The PCI7410 device is capable of detecting all the UltraMedia devices defined by the PCMCIA Proposal 0262 –
SmartMedia cards, MultiMedia Cards, Secure Digital, and Memory Stick devices. The detection of these devices is
made possible through circuitry included in the PCI7410 device and the UltraMedia adapters used to interface these
devices with the PC Card/CardBus sockets. No additional hardware requirements are placed on the system designer
in order to support these devices.
The PC Card Standard addresses the card detection and recognition process through an interrogation procedure that
the socket must initiate upon card insertion into a cold, unpowered socket. Through this interrogation, card voltage
requirements and interface type (16-bit vs. CardBus) are determined. The scheme uses the CD1, CD2, VS1, and VS2
signals (CCD1, CCD2, CVS1, CVS2 for CardBus). A PC Card designer connects these four terminals in a certain
configuration to indicate the type of card and its supply voltage requirements. The encoding scheme for this, defined
in the PC Card Standard, is shown in Table 3–2.
3–7
Table 3–2. PC Card—Card Detect and Voltage Sense Connections
CD2//CCD2
CD1//CCD1
VS2//CVS2
VS1//CVS1
Key
Interface
Ground
Ground
Ground
Ground
Open
Open
5V
16-bit PC Card
Open
Ground
5V
16-bit PC Card
VCC
5V
VPP/VCORE
Per CIS (VPP)
5 V and 3.3 V
Per CIS (VPP)
5 V, 3.3 V, and
Per CIS (VPP)
Ground
Ground
Ground
Ground
5V
16-bit PC Card
Ground
Ground
Open
Ground
LV
16-bit PC Card
3.3 V
Per CIS (VPP)
Ground
Connect to
CVS1
Open
Connect to
CCD1
LV
CardBus PC Card
3.3 V
Per CIS (VPP)
Ground
X.X V
Ground
Ground
Ground
LV
16-bit PC Card
3.3 V and X.X V
Per CIS (VPP)
Connect to
CVS2
Ground
Connect to
CCD2
Ground
LV
CardBus PC Card
3.3 V and X.X V
Per CIS (VPP)
Connect to
CVS1
Ground
Ground
Connect to
CCD2
LV
CardBus PC Card
3.3 V, X.X V,
and Y.Y V
Per CIS (VPP)
Ground
Ground
Ground
Open
LV
16-bit PC Card
Y.Y V
Per CIS (VPP)
Connect to
CVS2
Ground
Connect to
CCD2
Open
LV
CardBus PC Card
Y.Y V
1.8 V (VCORE)
Ground
Connect to
CVS2
Connect to
CCD1
Open
LV
CardBus PC Card
X.X V and Y.Y V
Per CIS (VPP)
Connect to
CVS1
Ground
Open
Connect to
CCD2
LV
CardBus PC Card
Y.Y V
Per CIS (VPP)
Ground
Connect to
CVS1
Ground
Connect to
CCD1
LV
UltraMedia
Ground
Connect to
CVS2
Connect to
CCD1
Ground
Reserved
Per query terminals
Reserved
PCMCIA Proposal 0262 has defined the first (previously) reserved response to be the indication that an UltraMedia
card has been detected. Specifically, if the PCI7410 device determines that the CD1 signal is connected to the VS1
signal, and that the CD2 and VS2 signals are both connected to ground, it interprets this as the insertion of an
UltraMedia card adapter.
Once an insertion has been detected, the PCI7410 device monitors the Media Card Detect (UM_CD) signal from the
socket to determine if an UltraMedia card is present in the adapter. This ensures that UltraMedia adapter cards
function the same as current adapter cards and are not detected or powered until an UltraMedia card is present.
Once UM_CD is detected low, indicating a media card is present, the PCI7410 device asserts the socket query driver
signal (SQRYDRV) high and monitors the SQRY[10:1] signals to determine the UltraMedia interface type and its
corresponding voltage requirements. The query signal assignments are given in Table 3–3 through Table 3–5. An
example of a particular UltraMedia device, and the SQRY connections provided by the UltraMedia adapter and card,
is shown in Figure 3–4.
Table 3–3. Query Terminal Definition
SQRYx TERMINAL
FUNCTION
10–7
Reserved (connect to ground)
6–3
Interface implementation
2–1
Card voltage
Table 3–4. Query Terminals – Voltage
3–8
SQRY2
SQRY1
CARD VOLTAGE
0
0
0
1
VCC = 3.3 V, VPP/VCORE = 1.8 V
VCC = 5 V, VPP/VCORE = 3.3 V
1
0
Option B
1
1
Option C
Table 3–5. Query Terminals – Media Interface Implementation
SQRY6
SQRY5
SQRY4
SQRY3
INTERFACE IMPLEMENTATION
0
0
0
0
Reserved
0
0
0
1
SmartMedia interface
0
0
1
0
MMC/SD interface
0
0
1
1
Memory Stick interface
0
1
0
0
Reserved
0
1
0
1
Reserved
0
1
1
X
Reserved
1
X
X
X
Reserved
10 kΩ
SQRYDRV
SQRY1
SQRY2
SQRY3
SQRY4
SQRY5
PCI7410 UltraMedia Controller
SQRY6
UltraMedia Adapter and Card
SQRY7
SQRY8
SQRY9
SQRY10
Figure 3–4. Example Query Terminal Configuration
When the query process has completed, the PCI7410 device updates its internal registers and signals the card
insertion to the host. The SQRY[10:1] terminals are switched to ground. UltraMedia devices are reported as 5-V,
16-bit cards through the socket present state register (CardBus offset 08h, see Section 6.3). The host requests that
5-V power be applied the socket, and the PCI7410 device automatically overrides this request and signals the TI
TPS222x power switch for the appropriate voltage levels (VCC and VPP/VCORE) determined from the query process.
3.6.4
Query Terminals
The UltraMedia query terminal assignments and definitions are listed in Table 3–3 through Table 3–5. If a 1 value is
needed for a query terminal, then that terminal is connected to the query driver terminal. If a 0 value is needed for
a query terminal, then that terminal is connected to ground.
As an example, Figure 3–4 shows the query terminal configuration for a 3.3-V VCC and 1.8-V VCORE UltraMedia card
with a SmartMedia interface.
3.6.5
Power Switch Interface
The power switch interface of the PCI7410 device is a 4-pin parallel interface. This 4-pin interface is implemented
such that the PCI7410 device can connect to both the TPS2211A and TPS2221 power switches. Bit 10
(12V_SW_SEL) in the general control register (PCI offset 86h, see Section 4.32) selects the power switch that is
implemented. The PCI7410 device defaults to use the control logic for the TPS2221 power switch. See Table 3–6
and Table 3–7 below for the power switch control logic.
3–9
Table 3–6. TPS2221 Control Logic
VD0/VCCD1
VD1/VCCD0
VD2/VPPD1
VD3/VPPD0
0
VCC
0V
VPP/VCORE
0V
0
0
0
0
0
0
0
0
1
1
Hi-Z
Hi-Z
0
Hi-Z
Hi-Z
0
0
1
0
1
0
1
Hi-Z
Hi-Z
0
3.3 V
0V
0
1
0
1
0
1
3.3 V
3.3 V
1
0
3.3 V
0
5V
1
1
1
3.3 V
1.8 V
1
0
0
0
5V
0V
1
0
0
1
5V
3.3V
1
0
1
0
5V
5V
1
0
1
1
5V
1.8 V
1
1
0
0
Hi-Z
Hi-Z
1
1
0
1
3.3 V
Hi-Z
1
1
1
0
5V
Hi-Z
1
1
1
1
Hi-Z
Hi-Z
VD0/VCCD1
VD1/VCCD0
VD2/VPPD1
VD3/VPPD0
0
0
0
0
VCC
0V
VPP/VCORE
0V
0
0
0
1
0V
12 V
0
0
1
0
0V
0V
0
0
1
1
0V
Hi-Z
0
1
0
0
3.3 V
0V
0
1
0
1
3.3 V
12 V
0
1
1
0
3.3 V
3.3 V
0
1
1
1
3.3 V
Hi-Z
1
0
0
0
5V
0V
1
0
0
1
5V
12 V
1
0
1
0
5V
5V
1
0
1
1
5V
Hi-Z
1
1
0
0
0V
0V
1
1
0
1
0V
12 V
1
1
1
0
0V
0V
1
1
1
1
0V
Hi-Z
Table 3–7. TPS2211A Control Logic
3.6.6
Zoomed Video Support
The PCI7410 device allows for the implementation of zoomed video (ZV) for PC Cards. Zoomed video is supported
by setting bit 6 (ZVENABLE) in the card control register (PCI offset 91h, see Section 4.39) on a per-socket function
basis. Setting this bit puts 16-bit PC Card address lines A25–A4 of the PC Card interface in the high-impedance state.
These lines can then transfer video and audio data directly to the appropriate controller. Card address lines A3–A0
can still access PC Card CIS registers for PC Card configuration. Figure 3–5 illustrates a PCI7410 ZV
implementation.
3–10
Speakers
CRT
Motherboard
PCI Bus
VGA
Controller
Audio
Codec
Zoomed Video
Port
19
PCM
Audio
Input
PC Card
19
4
PC Card
Interface
PCI7410
Video
Audio
4
Figure 3–5. Zoomed Video Implementation Using the PCI7410 Device
Not shown in Figure 3–5 is the multiplexing scheme used to route the socket ZV source to the graphics controller.
The PCI7410 device provides ZVSTAT and ZVSEL0 signals on the multifunction terminals to switch external bus
drivers. Figure 3–6 shows an implementation for switching between two ZV streams using external logic.
1
PCI7410
ZVSTAT
ZVSEL0
0
Figure 3–6. Zoomed Video Switching Application
Figure 3–6 illustrates an implementation using standard three-state bus drivers with active-low output enables.
ZVSEL0 is an active-low output indicating that the CardBus socket ZV mode is enabled. Table 3–8 illustrates the
functionality of the ZV output signals.
3–11
Table 3–8. Functionality of the ZV Output Signals
INPUTS
3.6.7
OUTPUTS
PORTSEL
SOCKET ENABLE
ZVSEL0
ZVSTAT
X
0
1
0
0
1
0
1
0
0
1
1
1
X
1
1
1
1
0
1
Standardized Zoomed-Video Register Model
The standardized zoomed-video register model is defined for the purpose of standardizing the ZV port control for PC
Card controllers across the industry. The following list summarizes the standardized zoomed-video register model
changes to the existing PC Card register set.
•
Socket present state register (CardBus socket address + 08h, see Section 6.3)
Bit 27 (ZVSUPPORT) has been added. The platform BIOS can set this bit via the socket force event register
(CardBus socket address + 0Ch, see Section 6.4) to define whether zoomed video is supported on that
socket by the platform.
•
Socket force event register (CardBus socket address + 0Ch, see Section 6.4)
Bit 27 (FZVSUPPORT) has been added. The platform BIOS can use this bit to set bit 27 (ZVSUPPORT)
in the socket present state register (CardBus socket address + 08h, see Section 6.3) to define whether
zoomed video is supported on that socket by the platform.
•
Socket control register (CardBus socket address +10h, see Section 6.5)
Bit 11 (ZV_ACTIVITY) has been added. This bit is set when zoomed video is enabled for either of the PC
Card sockets.
Bit 10 (STANDARDZVREG) has been added. This bit defines whether the PC Card controller supports the
standardized zoomed-video register model.
Bit 9 (ZVEN) is provided for software to enable or disable zoomed video, per socket.
If the ZV_EN bit (bit 0) in the diagnostic register (PCI offset 93h, see Section 4.41) is 1, then the standardized zoomed
video register model is disabled. For backward compatibility, even if the ZV_EN bit is 0 (enabled), the PCI7410 device
allows software to access zoomed video through the legacy address in the card control register (PCI offset 91h, see
Section 4.39), or through the new register model in the socket control register (CardBus socket address + 10h, see
Section 6.5).
3.6.8
Internal Ring Oscillator
The internal ring oscillator provides an internal clock source for the PCI7410 device so that neither the PCI clock nor
an external clock is required in order for the PCI7410 device to power down a socket or interrogate a PC Card. This
internal oscillator, operating nominally at 16 kHz, is always enabled.
3.6.9
Integrated Pullup Resistors for PC Card Interface
The PC Card Standard requires pullup resistors on various terminals to support both CardBus and 16-bit PC Card
configurations. Table 3–9 lists these terminals. The PCI7410 device has integrated all of these pullup resistors and
requires no additional external components. The I/O buffer on the BVD1(STSCHG)/CSTSCHG terminal has the
capability to switch to an internal pullup resistor when a 16-bit PC Card is inserted, or switch to an internal pulldown
resistor when a CardBus card is inserted. This prevents inadvertent CSTSCHG events. The pullup resistor
requirements for the various UltraMedia interfaces are either included in the UltraMedia cards (or the UltraMedia
adapter) or are part of the existing PCMCIA architecture. The PCI7410 device does not require any additional
components for UltraMedia support.
3–12
Table 3–9. Terminals With Integrated Pullup Resistors
TERMINAL NUMBER
SIGNAL NAME
TERMINAL NUMBER
SIGNAL NAME
PDV
GHK
PDV
GHK
A14 // CPERR
154
F15
CD2 // CCD2
187
C09
A15 // CIRDY
160
F13
INPACK // CREQ
173
B12
A19 // CBLOCK
153
E18
READY // CINT
182
C10
A20 // CSTOP
155
E17
RESET // CRST
169
B13
A21 // CDEVSEL
157
A16
VS1 // CVS1
181
B10
A22 // CTRDY
159
E14
VS2 // CVS2
167
F12
BVD1(STSCHG/RI) // CSTSCHG
185
A09
WAIT // CSERR
183
E10
BVD2(SPKR) // CAUDIO
184
F10
WP(IOIS16) // CCLKRUN
186
B09
CD1 // CCD1
125
L17
3.6.10 SPKROUT and CAUDPWM Usage
The SPKROUT terminal carries the digital audio signal from the PC Card to the system. When a 16-bit PC Card is
configured for I/O mode, the BVD2 terminal becomes the SPKR input terminal from the card. This terminal, in
CardBus applications, is referred to as CAUDIO. SPKR passes a TTL-level binary audio signal to the PCI7410 device.
The CardBus CAUDIO signal also can pass a single-amplitude binary waveform as well as a PWM signal. The binary
audio signal from each PC Card sockets is enabled by bit 1 (SPKROUTEN) of the card control register (PCI offset
91h, see Section 4.39).
Older controllers support CAUDIO in binary or PWM mode but use the same output terminal (SPKROUT). Some
audio chips may not support both modes on one terminal and may have a separate terminal for binary and PWM.
The PCI7410 implementation includes a signal for PWM, CAUDPWM, which can be routed to an MFUNC terminal.
Bit 2 (AUD2MUX), located in the card control register, is programmed to route a CardBus CAUDIO PWM terminal
to CAUDPWM. See Section 4.37, Multifunction Routing Register, for details on configuring the MFUNC terminals.
Figure 3–7 illustrates the SPKROUT connection.
System
Core Logic
BINARY_SPKR
SPKROUT
Speaker
Subsystem
PCI7410
CAUDPWM
PWM_SPKR
Figure 3–7. SPKROUT Connection to Speaker Driver
3.6.11 LED Socket Activity Indicators
The socket activity LEDs are provided to indicate when a PC Card is being accessed. The LEDA1 signal can be routed
to the multifunction terminals. When configured for LED output, this terminal outputs an active high signal to indicate
socket activity. The LED_SKT output indicates socket activity to the CardBus socket. See Section 4.37, Multifunction
Routing Status Register, for details on configuring the multifunction terminals.
The active-high LED signal is driven for 64 ms. When the LED is not being driven high, it is driven to a low state. Either
of the two circuits shown in Figure 3–8 can be implemented to provide LED signaling, and the board designer must
implement the circuit that best fits the application.
The LED activity signals are valid when a card is inserted, powered, and not in reset. For PC Card-16, the LED activity
signals are pulsed when READY(IREQ) is low. For CardBus cards, the LED activity signals are pulsed if CFRAME,
IRDY, or CREQ are active.
3–13
Current Limiting
R ≈ 500 Ω
LED
PCI7410
ApplicationSpecific Delay
Current Limiting
R ≈ 500 Ω
LED
PCI7410
Figure 3–8. Two Sample LED Circuits
As indicated, the LED signals are driven for a period of 64 ms by a counter circuit. To avoid the possibility of the LEDs
appearing to be stuck when the PCI clock is stopped, the LED signaling is cut off when the SUSPEND signal is
asserted, when the PCI clock is to be stopped during the clock run protocol, or when in the D2 or D1 power state.
If any additional socket activity occurs during this counter cycle, then the counter is reset and the LED signal remains
driven. If socket activity is frequent (at least once every 64 ms), then the LED signals remain driven.
3.6.12 CardBus Socket Registers
The PCI7410 device contains all registers for compatibility with the PCI Local Bus Specification and the PC Card
Standard. These registers, which exist as the CardBus socket registers, are listed in Table 3–10.
Table 3–10. CardBus Socket Registers
REGISTER NAME
OFFSET
Socket event
00h
Socket mask
04h
Socket present state
08h
Socket force event
0Ch
Socket control
Reserved
Socket power management
10h
14h–1Ch
20h
3.6.13 PCI Firmware Loading Function Programming Model
Function 3 of the PCI7410 device is a firmware loader function. This function provides an I/O window that a software
driver uses to load the PCI7410 firmware into the internal RAM. A simplified method of operation follows:
1. GRST assertions reset the internal RAM and the function 3 firmware loader.
2. While loading the firmware, the controller holds the UltraMedia core in reset.
3. The firmware loading software driver interfaces to function 3 and loads the firmware.
4. The software driver indicates load completion to UltraMedia via bit 2 (DONE) of the firmware loader control
register (offset 04h, see Section 3.6.13.2) in the function 3 I/O window.
The software driver that interfaces with PCI function 3 of the PCI7410 device loads the firmware into the program RAM
via the allocated I/O window for that function. Two I/O addresses are allocated, and these are used to load firmware
to the PCI7410 program RAM. The functionality of these I/O registers is listed in Table 3–11.
3–14
Table 3–11. Firmware Loader I/O Register Map
REGISTER NAME
OFFSET
Data/address
00h
Firmware loader control
04h
3.6.13.1 Data/Address Register
When bit 3 (ADDR_RST) is set in the firmware loader control register (offset 04h, see Section 3.6.13.2), the next data
written to this register is a doubleword that specifies the start address of the next block of internal RAM to be loaded.
When the doubleword of address information is written to this field, the ADDR_RST bit is automatically cleared and
the following writes to this register represent the internal RAM data. Because the internal RAM in the PCI7410 device
is 16 bits wide, the internal RAM data written to this register is written one word at a time. The internal RAM address
is autoincremented after each word of internal RAM data is written to this location. It is appropriate to buffer requests
to the internal RAM and retry PCI writes to this register when the buffer is full. If the firmware loader is unable to update
the RAM, then a PCI slave retry time-out occurs, data is lost, and bit 0 (ERR) in the control register is set.
Bit
31
30
29
28
27
26
25
RW
RW
RW
RW
RW
RW
RW
RW
Default
1
1
1
1
1
1
1
1
Bit
15
14
13
12
11
10
9
8
Name
Type
Default
23
22
21
20
19
18
17
16
RW
RW
RW
RW
RW
RW
RW
RW
1
1
1
1
1
1
1
1
7
6
5
4
3
2
1
0
Data address
Name
Type
24
Data address
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Register:
Offset:
Type:
Default:
Data address
00h
Read/Write
FFFF FFFFh
3.6.13.2 Firmware Loader Control Register
This register contains various control and status bits for the firmware loader. Bit descriptions are given in Table 3–12.
Bit
31
30
29
28
27
26
Name
Type
25
24
23
22
21
20
19
18
17
16
Firmware loader control
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Type
R
R
R
R
R
R
R
R
R
R
R
R
W
RW
R
RU
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Name
Firmware loader control
Register:
Offset:
Type:
Default:
Firmware loader control
04h
Read-only, Write-only, Read/Update, Read/Write
0000 0000h
3–15
Table 3–12. Firmware Loader Control Register Description
BIT
31–4
SIGNAL
TYPE
FUNCTION
RSVD
R
Reserved. These bits are read-only and return 0s when read.
3
ADDR_RST
W
Address reset. When set, this bit indicates that the next data written to the data/address register will be a
doubleword that specifies the start address of the next block of internal RAM to be loaded. This bit is selfcleared when the address is written to the data/address register.
2
DONE
RW
RAM load done. Setting this bit to 1 indicates to the firmware loader function that the firmware loading is
complete for the RAM selected by the address written when ADDR_RST was set, and embedded controllers can begin accessing the RAM.
1
RSVD
0
ERR
R
RU
Reserved. This bit is read-only and returns 0 when read.
When set, this bit indicates that there was an error during the loading of the internal RAM. This field indicates
all loading errors. Software must check this bit after loading each RAM to ensure that the data was loaded
successfully. This bit is cleared by a read of this register.
3.7 Serial EEPROM Interface
The PCI7410 device has a dedicated serial bus interface that can be used with an EEPROM to load certain registers
in the PCI7410 device. The EEPROM is detected by a pullup resistor on the SCL terminal. See Table 3–14 for the
EEPROM loading map.
3.7.1
Serial-Bus Interface Implementation
The PCI7410 device drives SCL at nearly 100 kHz during data transfers, which is the maximum specified frequency
for standard mode I2C. The serial EEPROM must be located at address A0h.
Some serial device applications may include PC Card power switches, ZV source switches, card ejectors, or other
devices that may enhance the user’s PC Card experience. The serial EEPROM device and PC Card power switches
are discussed in the sections that follow.
3.7.2
Accessing Serial-Bus Devices Through Software
The PCI7410 device provides a programming mechanism to control serial bus devices through software. The
programming is accomplished through a doubleword of PCI configuration space at offset B0h. Table 3–13 lists the
registers used to program a serial-bus device through software.
Table 3–13. PCI7410 Registers Used to Program Serial-Bus Devices
PCI OFFSET
REGISTER NAME
DESCRIPTION
B0h
Serial-bus data
Contains the data byte to send on write commands or the received data byte on read commands.
B1h
Serial-bus index
The content of this register is sent as the word address on byte writes or reads. This register is not used
in the quick command protocol.
B2h
Serial-bus slave
address
Write transactions to this register initiate a serial-bus transaction. The slave device address and the
R/W command selector are programmed through this register.
B3h
Serial-bus control
and status
Read data valid, general busy, and general error status are communicated through this register. In
addition, the protocol-select bit is programmed through this register.
3.7.3
Serial-Bus Interface Protocol
The SCL and SDA signals are bidirectional, open-drain signals and require pullup resistors as shown in Figure 3–3.
The PCI7410 device, which supports up to 100-Kb/s data-transfer rate, is compatible with standard mode I2C using
7-bit addressing.
All data transfers are initiated by the serial bus master. The beginning of a data transfer is indicated by a start
condition, which is signaled when the SDA line transitions to the low state while SCL is in the high state, as shown
in Figure 3–9. The end of a requested data transfer is indicated by a stop condition, which is signaled by a low-to-high
3–16
transition of SDA while SCL is in the high state, as shown in Figure 3–9. Data on SDA must remain stable during the
high state of the SCL signal, as changes on the SDA signal during the high state of SCL are interpreted as control
signals, that is, a start or a stop condition.
SDA
SCL
Start
Condition
Stop
Condition
Change of
Data Allowed
Data Line Stable,
Data Valid
Figure 3–9. Serial-Bus Start/Stop Conditions and Bit Transfers
Data is transferred serially in 8-bit bytes. The number of bytes that may be transmitted during a data transfer is
unlimited; however, each byte must be completed with an acknowledge bit. An acknowledge (ACK) is indicated by
the receiver pulling the SDA signal low, so that it remains low during the high state of the SCL signal. Figure 3–10
illustrates the acknowledge protocol.
SCL From
Master
1
2
3
7
8
9
SDA Output
By Transmitter
SDA Output
By Receiver
Figure 3–10. Serial-Bus Protocol Acknowledge
The PCI7410 device is a serial bus master; all other devices connected to the serial bus external to the PCI7410
device are slave devices. As the bus master, the PCI7410 device drives the SCL clock at nearly 100 kHz during bus
cycles and places SCL in a high-impedance state (zero frequency) during idle states.
Typically, the PCI7410 device masters byte reads and byte writes under software control. Doubleword reads are
performed by the serial EEPROM initialization circuitry upon a PCI reset and may not be generated under software
control. See Section 3.7.4, Serial-Bus EEPROM Application, for details on how the PCI7410 device automatically
loads the subsystem identification and other register defaults through a serial-bus EEPROM.
Figure 3–11 illustrates a byte write. The PCI7410 device issues a start condition and sends the 7-bit slave device
address and the command bit zero. A 0 in the R/W command bit indicates that the data transfer is a write. The slave
device acknowledges if it recognizes the address. If no acknowledgment is received by the PCI7410 device, then an
appropriate status bit is set in the serial-bus control/status register (PCI offset B3h, see Section 4.51). The word
address byte is then sent by the PCI7410 device, and another slave acknowledgment is expected. Then the PCI7410
device delivers the data byte MSB first and expects a final acknowledgment before issuing the stop condition.
3–17
Slave Address
S
Word Address
b6 b5 b4 b3 b2 b1 b0
0
A
Data Byte
b7 b6 b5 b4 b3 b2 b1 b0
A b7 b6 b5 b4 b3 b2 b1 b0
A
P
R/W
A = Slave Acknowledgement
S/P = Start/Stop Condition
Figure 3–11. Serial-Bus Protocol—Byte Write
Figure 3–12 illustrates a byte read. The read protocol is very similar to the write protocol, except the R/W command
bit must be set to 1 to indicate a read-data transfer. In addition, the PCI7410 master must acknowledge reception
of the read bytes from the slave transmitter. The slave transmitter drives the SDA signal during read data transfers.
The SCL signal remains driven by the PCI7410 master.
Slave Address
S
Word Address
b6 b5 b4 b3 b2 b1 b0
Start
0
A
Slave Address
b7 b6 b5 b4 b3 b2 b1 b0
R/W
A
S
b6 b5 b4 b3 b2 b1 b0
Restart
1
A
R/W
Data Byte
b7 b6 b5 b4 b3 b2 b1 b0
M
P
Stop
A = Slave Acknowledgement
M = Master Acknowledgement
S/P = Start/Stop Condition
Figure 3–12. Serial-Bus Protocol—Byte Read
Figure 3–13 illustrates EEPROM interface doubleword data collection protocol.
Slave Address
S
1
0
1
0
0
Word Address
0
0
Start
0
A
Slave Address
b7 b6 b5 b4 b3 b2 b1 b0
M
A = Slave Acknowledgement
S
1
0
1
0
0
Restart
R/W
Data Byte 3
A
Data Byte 2
M
Data Byte 1
M = Master Acknowledgement
M
Data Byte 0
0
0
1
A
R/W
M
P
S/P = Start/Stop Condition
Figure 3–13. EEPROM Interface Doubleword Data Collection
3.7.4
Serial-Bus EEPROM Application
When the PCI bus is reset and the serial-bus interface is detected, the PCI7410 device attempts to read the
subsystem identification and other register defaults from a serial EEPROM.
This format must be followed for the PCI7410 device to load initializations from a serial EEPROM. All bit fields must
be considered when programming the EEPROM.
The serial EEPROM is addressed at slave address 1010 000b by the PCI7410 device. All hardware address bits for
the EEPROM must be tied to the appropriate level to achieve this address. The serial EEPROM chip in the sample
application (Figure 3–13) assumes the 1010b high-address nibble. The lower three address bits are terminal inputs
to the chip, and the sample application shows these terminal inputs tied to GND.
3–18
Table 3–14. EEPROM Loading Map
SERIAL ROM
OFFSET
BYTE DESCRIPTION
00h
CardBus function indicator (00h)
01h
Number of bytes (20h)
02h
PCI 04h, command register, function 0, bits 8, 6–5, 2–0
[7]
[6]
[5]
[4:3]
[2]
[1]
[0]
Command
register, bit 8
Command
register, bit 6
Command
register, bit 5
RSVD
Command
register, bit 2
Command
register, bit 1
Command
register, bit 0
[7]
[6]
[5]
[4:3]
[2]
[1]
[0]
Command
register, bit 8
Command
register, bit 6
Command
register, bit 5
RSVD
Command
register, bit 2
Command
register, bit 1
Command
register, bit 0
03h
PCI 04h, command register, function 1, bits 8, 6–5, 2–0
04h
PCI 40h, subsystem vendor ID, byte 0
05h
PCI 41h, subsystem vendor ID, byte 1
06h
PCI 42h, subsystem ID, byte 0
07h
PCI 43h, subsystem ID, byte 1
08h
PCI 44h, PC Card 16-bit I/F legacy mode base address register, byte 0, bits 7–1
09h
PCI 45h, PC Card 16-bit I/F legacy mode base address register, byte 1
0Ah
PCI 46h, PC Card 16-bit I/F legacy mode base address register, byte 2
0Bh
PCI 47h, PC Card 16-bit I/F legacy mode base address register, byte 3
0Ch
PCI 80h, system control, function 0, byte 0, bits 6–0
0Dh
PCI 80h, system control, function 1, byte 0, bit 2
0Eh
PCI 81h, system control, byte 1
0Fh
Reserved load all 0s (PCI 82h, system control, byte 2)
10h
PCI 83h, system control, byte 3
11h
PCI 8Ch, MFUNC routing, byte 0
12h
PCI 8Dh, MFUNC routing, byte 1
13h
PCI 8Eh, MFUNC routing, byte 2
14h
PCI 8Fh, MFUNC routing, byte 3
15h
PCI 90h, retry status, bits 7, 6
16h
PCI 91h, card control, bit 7
17h
PCI 92h, device control, bits 6, 5, 3–0
18h
PCI 93h, diagnostic, bits 7, 4–0
19h
PCI A2h, power-management capabilities, function 0, bit 15 (bit 7 of EEPROM offset 16h corresponds to bit 15)
1Ah
PCI A2h, power-management capabilities, function 1, bit 15 (bit 7 of EEPROM offset 16h corresponds to bit 15)
1Bh
CB Socket + 0Ch, function 0 socket force event, bit 27 (bit 3 of EEPROM offset 17h corresponds to bit 27)
1Ch
CB Socket + 0Ch, function 1 socket force event, bit 27 (bit 3 of EEPROM offset 18h corresponds to bit 27)
1Dh
ExCA 00h, ExCA identification and revision, bits 7–0
1Eh
PCI 86h, general control, byte 0, bits 5, 4, 3, 1, 0
1Fh
PCI 87h, general control, byte 1, bits 4–2
3–19
Table 3–14. EEPROM Loading Map (Continued)
SERIAL ROM
OFFSET
BYTE DESCRIPTION
20h
PCI 89h, GPE enable, bits 7, 6, 4–0
21h
PCI 8Bh, general-purpose output, bits 4–0
22h
1394 OHCI function indicator (02h)
23h
24h
Number of bytes (17h)
PCI 3Fh, maximum latency bits 7–4
PCI 3Eh, minimum grant, bits 3–0
25h
PCI 2Ch, subsystem vendor ID, byte 0
26h
PCI 2Dh, subsystem vendor ID, byte 1
27h
PCI 2Eh, subsystem ID, byte 0
28h
PCI 2Fh, subsystem ID, byte 1
29h
PCI F4h, Link_Enh, byte 0, bits 7, 2, 1
OHCI 50h, host controller control, bit 23
2Ah
[7]
[6]
[5:3]
[2]
[1]
[0]
Link_Enh.
enab_unfair
HCControl.Program Phy
Enable
RSVD
Link_Enh, bit 2
Link_Enh.
enab_accel
RSVD
Mini-ROM address, this byte indicates the MINI ROM offset into the EEPROM
00h = No MINI ROM
Other Values = MINI ROM offset
3–20
2Bh
OHCI 24h, GUIDHi, byte 0
2Ch
OHCI 25h, GUIDHi, byte 1
2Dh
OHCI 26h, GUIDHi, byte 2
2Eh
OHCI 27h, GUIDHi, byte 3
2Fh
OHCI 28h, GUIDLo, byte 0
30h
OHCI 29h, GUIDLo, byte 1
31h
OHCI 2Ah, GUIDLo, byte 2
32h
OHCI 2Bh, GUIDLo, byte 3
33h
Checksum (Reserved—no bit loaded)
34h
PCI F5h, Link_Enh, byte 1, bits 7, 6, 5, 4
35h
PCI F0h, PCI miscellaneous, byte 0, bits 5, 4, 2, 1, 0
36h
PCI F1h, PCI miscellaneous, byte 1, bits 7, 3, 2, 1, 0
37h
Reserved
38h
Reserved (CardBus CIS pointer)
39h
Reserved
3Ah
PCI ECh, PCI PHY control, bits 7, 3, 1
3Bh
Firmware loader function indicator (03h)
3Ch
Number of bytes (05h)
3Dh
PCI 2Ch, subsystem vendor ID, byte 0
3Eh
PCI 2Dh, subsystem vendor ID, byte 1
3Fh
PCI 2Eh, subsystem ID, byte 0
40h
PCI 2Fh, subsystem ID, byte 1
41h
PCI 50h, miscellaneous control, bit 0
42h
End-of-list indicator (80h)
3.8 Programmable Interrupt Subsystem
Interrupts provide a way for I/O devices to let the microprocessor know that they require servicing. The dynamic
nature of PC Cards and the abundance of PC Card I/O applications require substantial interrupt support from the
PCI7410 device. The PCI7410 device provides several interrupt signaling schemes to accommodate the needs of
a variety of platforms. The different mechanisms for dealing with interrupts in this device are based on various
specifications and industry standards. The ExCA register set provides interrupt control for some 16-bit PC Card
functions, and the CardBus socket register set provides interrupt control for the CardBus PC Card functions. The
PCI7410 device is, therefore, backward compatible with existing interrupt control register definitions, and new
registers have been defined where required.
The PCI7410 device detects PC Card interrupts and events at the PC Card interface and notifies the host controller
using one of several interrupt signaling protocols. To simplify the discussion of interrupts in the PCI7410 device, PC
Card interrupts are classified either as card status change (CSC) or as functional interrupts.
The method by which any type of PCI7410 interrupt is communicated to the host interrupt controller varies from
system to system. The PCI7410 device offers system designers the choice of using parallel PCI interrupt signaling,
parallel ISA-type IRQ interrupt signaling, or the IRQSER serialized ISA and/or PCI interrupt protocol. It is possible
to use the parallel PCI interrupts in combination with either parallel IRQs or serialized IRQs, as detailed in the sections
that follow. All interrupt signaling is provided through the seven multifunction terminals, MFUNC0–MFUNC6.
3.8.1
PC Card Functional and Card Status Change Interrupts
PC Card functional interrupts are defined as requests from a PC Card application for interrupt service and are
indicated by asserting specially-defined signals on the PC Card interface. Functional interrupts are generated by
16-bit I/O PC Cards and by CardBus PC Cards.
Card status change (CSC)-type interrupts are defined as events at the PC Card interface that are detected by the
PCI7410 device and may warrant notification of host card and socket services software for service. CSC events
include both card insertion and removal from PC Card sockets, as well as transitions of certain PC Card signals.
Table 3–15 summarizes the sources of PC Card interrupts and the type of card associated with them. CSC and
functional interrupt sources are dependent on the type of card inserted in the PC Card socket. The four types of cards
that can be inserted into any PC Card socket are:
•
•
•
•
16-bit memory card
16-bit I/O card
CardBus cards
UltraMedia card
Table 3–15. Interrupt Mask and Flag Registers
CARD TYPE
16 bit memory
16-bit
16-bit I/O
16-bit I/O/
UltraMedia
All 16-bit PC
Cards/
UltraMedia/
Flash Media
CardBus
EVENT
MASK
FLAG
Battery conditions (BVD1, BVD2)
ExCA offset 05h/45h/805h bits 1 and 0
ExCA offset 04h/44h/804h bits 1 and 0
Wait states (READY)
ExCA offset 05h/45h/805h bit 2
ExCA offset 04h/44h/804h bit 2
Change in card status (STSCHG)
ExCA offset 05h/45h/805h bit 0
ExCA offset 04h/44h/804h bit 0
Interrupt request (IREQ)
Always enabled
PCI configuration offset 91h bit 0
Power cycle complete
ExCA offset 05h/45h/805h bit 3
ExCA offset 04h/44h/804h bit 3
Change in card status (CSTSCHG)
Socket mask bit 0
Socket event bit 0
Interrupt request (CINT)
Always enabled
PCI configuration offset 91h bit 0
Power cycle complete
Socket mask bit 3
Socket event bit 3
Card insertion or removal
Socket mask bits 2 and 1
Socket event bits 2 and 1
3–21
Functional interrupt events are valid only for 16-bit I/O and CardBus cards; that is, the functional interrupts are not
valid for 16-bit memory cards. Furthermore, card insertion and removal-type CSC interrupts are independent of the
card type.
Table 3–16. PC Card Interrupt Events and Description
CARD TYPE
EVENT
TYPE
SIGNAL
DESCRIPTION
BVD1(STSCHG)//CSTSCHG
A transition on BVD1 indicates a change in the
PC Card battery conditions.
BVD2(SPKR)//CAUDIO
A transition on BVD2 indicates a change in the
PC Card battery conditions.
Battery conditions
(BVD1, BVD2)
CSC
Wait states
(READY)
CSC
READY(IREQ)//CINT
16-bit I/O
Change in card
status (STSCHG)
CSC
BVD1(STSCHG)//CSTSCHG
The assertion of STSCHG indicates a status change
on the PC Card.
16-bit I/O/
UltraMedia
Interrupt request
(IREQ)
Functional
READY(IREQ)//CINT
The assertion of IREQ indicates an interrupt request
from the PC Card.
Change in card
status (CSTSCHG)
CSC
BVD1(STSCHG)//CSTSCHG
Interrupt request
(CINT)
Functional
READY(IREQ)//CINT
Card insertion
or removal
CSC
CD1//CCD1,
CD2//CCD2
Power cycle
complete
CSC
N/A
16-bit
memory
CardBus
All PC Cards/
UltraMedia/
Flash Media
A transition on READY indicates a change in the
ability of the memory PC Card to accept or provide
data.
The assertion of CSTSCHG indicates a status
change on the PC Card.
The assertion of CINT indicates an interrupt request
from the PC Card.
A transition on either CD1//CCD1 or CD2//CCD2
indicates an insertion or removal of a 16-bit or
CardBus PC Card.
An interrupt is generated when a PC Card power-up
cycle has completed.
The naming convention for PC Card signals describes the function for 16-bit memory, I/O cards, and CardBus. For
example, READY(IREQ)//CINT includes READY for 16-bit memory cards, IREQ for 16-bit I/O cards, and CINT for
CardBus cards. The 16-bit memory card signal name is first, with the I/O card signal name second, enclosed in
parentheses. The CardBus signal name follows after a double slash (//).
The 1997 PC Card Standard describes the power-up sequence that must be followed by the PCI7410 device when
an insertion event occurs and the host requests that the socket VCC and VPP be powered. Upon completion of this
power-up sequence, the PCI7410 interrupt scheme can be used to notify the host system (see Table 3–16), denoted
by the power cycle complete event. This interrupt source is considered a PCI7410 internal event, because it depends
on the completion of applying power to the socket rather than on a signal change at the PC Card interface.
3.8.2
Interrupt Masks and Flags
Host software may individually mask (or disable) most of the potential interrupt sources listed in Table 3–16 by setting
the appropriate bits in the PCI7410 device. By individually masking the interrupt sources listed, software can control
those events that cause a PCI7410 interrupt. Host software has some control over the system interrupt the PCI7410
device asserts by programming the appropriate routing registers. The PCI7410 device allows host software to route
PC Card CSC and PC Card functional interrupts to separate system interrupts. Interrupt routing somewhat specific
to the interrupt signaling method used is discussed in more detail in the following sections.
When an interrupt is signaled by the PCI7410 device, the interrupt service routine must determine which of the events
listed in Table 3–15 caused the interrupt. Internal registers in the PCI7410 device provide flags that report the source
of an interrupt. By reading these status bits, the interrupt service routine can determine the action to be taken.
Table 3–15 details the registers and bits associated with masking and reporting potential interrupts. All interrupts can
be masked except the functional PC Card interrupts, and an interrupt status flag is available for all types of interrupts.
Notice that there is not a mask bit to stop the PCI7410 device from passing PC Card functional interrupts through
to the appropriate interrupt scheme. These interrupts are not valid until the card is properly powered, and there must
never be a card interrupt that does not require service after proper initialization.
3–22
Table 3–15 lists the various methods of clearing the interrupt flag bits. The flag bits in the ExCA registers (16-bit PC
Card-related interrupt flags) can be cleared using two different methods. One method is an explicit write of 1 to the
flag bit to clear and the other is by reading the flag bit register. The selection of flag bit clearing methods is made by
bit 2 (IFCMODE) in the ExCA global control register (ExCA offset 1Eh/5Eh/81Eh, see Section 5.20), and defaults to
the flag-cleared-on-read method.
The CardBus-related interrupt flags can be cleared by an explicit write of 1 to the interrupt flag in the socket event
register (see Section 6.1). Although some of the functionality is shared between the CardBus registers and the ExCA
registers, software must not program the chip through both register sets when a CardBus card is functioning.
3.8.3
Using Parallel IRQ Interrupts
The seven multifunction terminals, MFUNC6–MFUNC0, implemented in the PCI7410 device can be routed to obtain
a subset of the ISA IRQs. The IRQ choices provide ultimate flexibility in PC Card host interruptions. To use the parallel
ISA-type IRQ interrupt signaling, software must program the device control register (PCI offset 92h, see
Section 4.40), to select the parallel IRQ signaling scheme. See Section 4.37, Multifunction Routing Status Register,
for details on configuring the multifunction terminals.
A system using parallel IRQs requires (at a minimum) one PCI terminal, INTA, to signal CSC events. This requirement
is dictated by certain card and socket-services software. The INTA requirement calls for routing the MFUNC0 terminal
for INTA signaling. The INTRTIE bit is used, in this case, to route socket interrupt events to INTA. This leaves (at a
maximum) six different IRQs to support legacy 16-bit PC Card functions.
As an example, suppose the six IRQs used by legacy PC Card applications are IRQ3, IRQ4, IRQ5, IRQ10, IRQ11,
and IRQ15. The multifunction routing status register must be programmed to a value of 0FBA 5432h. This value
routes the MFUNC0 terminal to INTA signaling and routes the remaining terminals as illustrated in Figure 3–14. Not
shown is that INTA must also be routed to the programmable interrupt controller (PIC), or to some circuitry that
provides parallel PCI interrupts to the host.
PCI7410
MFUNC1
IRQ3
PIC
MFUNC2
IRQ4
MFUNC3
IRQ5
MFUNC4
IRQ10
MFUNC5
IRQ11
MFUNC6
IRQ15
Figure 3–14. IRQ Implementation
Power-on software is responsible for programming the multifunction routing status register to reflect the IRQ
configuration of a system implementing the PCI7410 device. The multifunction routing status register is a global
register that is shared between the four PCI7410 functions. See Section 4.37, Multifunction Routing Status Register,
for details on configuring the multifunction terminals.
The parallel ISA-type IRQ signaling from the MFUNC6–MFUNC0 terminals is compatible with the input signal
requirements of the 8259 PIC. The parallel IRQ option is provided for system designs that require legacy ISA IRQs.
Design constraints may demand more MFUNC6–MFUNC0 IRQ terminals than the PCI7410 device makes available.
3.8.4
Using Parallel PCI Interrupts
Parallel PCI interrupts are available when exclusively in parallel PCI interrupt/parallel ISA IRQ signaling mode, and
when only IRQs are serialized with the IRQSER protocol. The INTA, INTB, and INTC can be routed to MFUNC
terminals (MFUNC0, MFUNC1, and MFUNC2). If bit 29 (INTRTIE) is set in the system control register (PCI offset 80h,
see Section 4.30) function 0 and function 1 share PCI INTA.
The INTRTIE and TIEALL bits affect the read-only value provided through accesses to the interrupt pin register (PCI
offset 3Dh, see Section 4.25). When the TIEALL bit is set, all three functions return a value of 01h on reads from the
interrupt pin register for both parallel and serial PCI interrupts. Table 3–17 summarizes the interrupt signaling modes.
3–23
Table 3–17. Interrupt Pin Register Cross Reference
3.8.5
INTRTIE Bit
TIEALL Bit
INTPIN
Function 0
(CardBus)
INTPIN
Function 1
(Dedicated Socket)
INTPIN
Function 2
(1394 OHCI)
0
0
0x01 (INTA)
0x02 (INTB)
0x03 (INTC)
1
0
0x01 (INTA)
0x01 (INTA)
0x03 (INTC)
X
1
0x01 (INTA)
0x01 (INTA)
0x01 (INTA)
Using Serialized IRQSER Interrupts
The serialized interrupt protocol implemented in the PCI7410 device uses a single terminal to communicate all
interrupt status information to the host controller. The protocol defines a serial packet consisting of a start cycle,
multiple interrupt indication cycles, and a stop cycle. All data in the packet is synchronous with the PCI clock. The
packet data describes 16 parallel ISA IRQ signals and the optional 4 PCI interrupts INTA, INTB, INTC, and INTD. For
details on the IRQSER protocol, refer to the document Serialized IRQ Support for PCI Systems.
3.8.6
SMI Support in the PCI7410 Device
The PCI7410 device provides a mechanism for interrupting the system when power changes have been made to the
PC Card socket interfaces. The interrupt mechanism is designed to fit into a system maintenance interrupt (SMI)
scheme. SMI interrupts are generated by the PCI7410 device, when enabled, after a write cycle to either the socket
control register (CB offset 10h, see Section 6.5) of the CardBus register set, or the ExCA power control register (ExCA
offset 02h/42h/802h, see Section 5.3) causes a power cycle change sequence to be sent on the power switch
interface.
The SMI control is programmed through three bits in the system control register (PCI offset 80h, see Section 4.30).
These bits are SMIROUTE (bit 26), SMISTATUS (bit 25), and SMIENB (bit 24). Table 3–18 describes the SMI control
bits function.
Table 3–18. SMI Control
BIT NAME
FUNCTION
SMIROUTE
This shared bit controls whether the SMI interrupts are sent as a CSC interrupt or as IRQ2.
SMISTAT
This socket dependent bit is set when an SMI interrupt is pending. This status flag is cleared by writing back a 1.
SMIENB
When set, SMI interrupt generation is enabled. This bit is shared by functions 0 and 1.
If CSC SMI interrupts are selected, then the SMI interrupt is sent as the CSC on a per-socket basis. The CSC interrupt
can be either level or edge mode, depending upon the CSCMODE bit in the ExCA global control register (ExCA offset
1Eh/5Eh/81Eh, see Section 5.20).
If IRQ2 is selected by SMIROUTE, then the IRQSER signaling protocol supports SMI signaling in the IRQ2 IRQ/Data
slot. In a parallel ISA IRQ system, the support for an active low IRQ2 is provided only if IRQ2 is routed to either
MFUNC3 or MFUNC6 through the multifunction routing status register (PCI offset 8Ch, see Section 4.37).
3.9 Power Management Overview
In addition to the low-power CMOS technology process used for the PCI7410 device, various features are designed
into the device to allow implementation of popular power-saving techniques. These features and techniques are as
follows:
•
•
•
•
•
•
3–24
Clock run protocol
Cardbus PC Card power management
16-bit PC Card power management
Suspend mode
Ring indicate
PCI power management
•
•
Cardbus bridge power management
ACPI support
PCI Bus
PRST
GRST†
TPS2211A or
TPS2221
Power Switch
PC Card
Socket A
4
Core Logic/
Embedded
Controller
CLKRUN
PCI7410
PME
68
TPS2020
Dedicated
Socket B
16
1394
Socket
† The system connection to GRST is implementation-specific. GRST must be asserted on initial power up of the PCI7410 device. PRST must be
asserted for subsequent warm resets.
Figure 3–15. System Diagram Implementing CardBus Device Class Power Management
3.9.1
1394 Power Management (Function 1)
The PCI7410 device complies with PCI Bus Power Management Interface Specification. The device supports the D0
(uninitialized), D0 (active), D1, D2, and D3 power states as defined by the power-management definition in the 1394
Open Host Controller Interface Specification, Appendix A.4 and PCI Bus Power Management Specification. PME is
supported to provide notification of wake events. Per Section A.4.2, the 1394 OHCI sets PMCSR.PME_STS in the
D0 state due to unmasked interrupt events. In previous OHCI implementations, unmasked interrupt events were
interpreted as (IntEvent.n && IntMask.n && IntMask.masterIntEnable), where n represents a specific interrupt event.
Based on feedback from Microsoft this implementation may cause problems with the existing Windows
power-management arcitecture as a PME and an interrupt could be simultaneously signaled on a transition from the
D1 to D0 state where interrupts were enabled to generate wake events. If bit 10 (ignore_mstrIntEna_for_pme) in the
PCI miscellaneous configuration register (OHCI offset F0h, see Section 7.23) is set, then the PCI7410 device
implements the preferred behavior as (IntEvent.n && IntMask.n). Otherwise, the PCI7410 device implements the
preferred behavior as (IntEvent.n && IntMask.n && IntMask.masterIntEnable). In addition, when the
ignore_mstrIntEna_for_pme bit is set, it causes bit 26 of the OHCI vendor ID register (OHCI offset 40h, see
Section 8.15) to read 1, otherwise, bit 26 reads 0. An open drain buffer is used for PME. If PME is enabled in the power
management control/status register (PCI offset A4h, see Section 4.45), then insertion of a PC Card or UltraMedia
Card causes the PCI7410 device to assert PME which wakes the system from a low power state (D3, D2, or D1).
The OS services PME and takes the PCI7410 device to the D0 state.
3.9.2
Integrated Low-Dropout Voltage Regulator (LDO-VR)
The PCI7410 device requires 1.8-V core voltage. The core power can be supplied by the PCI7410 device itself using
the internal LDO-VR. The core power can alternatively be supplied by an external power supply through the
VR_PORT terminal. Table 3–19 lists the requirements for both the internal core power supply and the external core
power supply.
3–25
Table 3–19. Requirements for Internal/External 1.8-V Core Power Supply
SUPPLY
VR_EN
VR_PORT
Internal
VCC
3.3 V
GND
1.8-V output
Internal 1.8-V LDO-VR is enabled. A 1.0-µF bypass capacitor is required on the VR_PORT
terminal for decoupling. This output is not for external use.
External
3.3 V
VCC
1.8-V input
Internal 1.8-V LDO-VR is disabled. An external 1.8-V power supply, of minimum 50-mA
capacity, is required. A 0.1-µF bypass capacitor on the VR_PORT terminal is required.
3.9.3
NOTE
Clock Run Protocol
The PCI CLKRUN feature is the primary method of power management on the PCI interface of the PCI7410 device.
CLKRUN signaling is provided through the MFUNC6 terminal. Since some chip sets do not implement CLKRUN, this
is not always available to the system designer, and alternate power-saving features are provided. For details on the
CLKRUN protocol see the PCI Mobile Design Guide.
The PCI7410 device does not permit the central resource to stop the PCI clock under any of the following conditions:
•
Bit 1 (KEEPCLK) in the system control register (PCI offset 80h, see Section 4.30) is set.
•
The 16-bit PC Card resource manager is busy.
•
The PCI7410 CardBus master state machine is busy. A cycle may be in progress on CardBus.
•
The PCI7410 master is busy. There may be posted data from CardBus to PCI in the PCI7410 device.
•
Interrupts are pending.
•
The CardBus CCLK for the socket has not been stopped by the PCI7410 CCLKRUN manager.
The PCI7410 device restarts the PCI clock using the CLKRUN protocol under any of the following conditions:
•
A 16-bit PC Card IREQ or a CardBus CINT has been asserted by either card.
•
A CardBus CBWAKE (CSTSCHG) or 16-bit PC Card STSCHG/RI event occurs in the socket.
•
A CardBus attempts to start the CCLK using CCLKRUN.
•
A CardBus card arbitrates for the CardBus bus using CREQ.
3.9.4
CardBus PC Card Power Management
The PCI7410 device implements its own card power-management engine that can turn off the CCLK to a socket when
there is no activity to the CardBus PC Card. The PCI clock-run protocol is followed on the CardBus CCLKRUN
interface to control this clock management.
3.9.5
16-Bit PC Card Power Management
The COE bit (bit 7) of the ExCA power control register (ExCA offset 02h/42h/802h, see Section 5.3) and PWRDWN
bit (bit 0) of the ExCA global control register (ExCA offset 1Eh/5Eh/81Eh, see Section 5.20) are provided for 16-bit
PC Card power management. The COE bit places the card interface in a high-impedance state to save power. The
power savings when using this feature are minimal. The COE bit resets the PC Card when used, and the PWRDWN
bit does not. Furthermore, the PWRDWN bit is an automatic COE, that is, the PWRDWN performs the COE function
when there is no card activity.
NOTE: The 16-bit PC Card must implement the proper pullup resistors for the COE and
PWRDWN modes.
3.9.6
Suspend Mode
The SUSPEND signal, provided for backward compatibility, gates the PRST (PCI reset) signal and the GRST (global
reset) signal from the PCI7410 device. Besides gating PRST and GRST, SUSPEND also gates PCLK inside the
PCI7410 device in order to minimize power consumption.
3–26
It should also be noted that asynchronous signals, such as card status change interrupts and RI_OUT, can be passed
to the host system without a PCI clock. However, if card status change interrupts are routed over the serial interrupt
stream, then the PCI clock must be restarted in order to pass the interrupt, because neither the internal oscillator nor
an external clock is routed to the serial-interrupt state machine. Figure 3–16 is a signal diagram of the suspend
function.
RESET
GNT
SUSPEND
PCLK
External Terminals
Internal Signals
RESETIN
SUSPENDIN
PCLKIN
Figure 3–16. Signal Diagram of Suspend Function
3.9.7
Requirements for Suspend Mode
The suspend mode prevents the clearing of all register contents on the assertion of reset (PRST or GRST) which
would require the reconfiguration of the PCI7410 device by software. Asserting the SUSPEND signal places the PCI
outputs of the controller in a high-impedance state and gates the PCLK signal internally to the controller unless a PCI
transaction is currently in process (GNT is asserted). It is important that the PCI bus not be parked on the PCI7410
device when SUSPEND is asserted because the outputs are in a high-impedance state.
The GPIOs, MFUNC signals, and RI_OUT signal are all active during SUSPEND, unless they are disabled in the
appropriate PCI7410 registers.
3.9.8
Ring Indicate
The RI_OUT output is an important feature in power management, allowing a system to go into a suspended mode
and wake-up on modem rings and other card events. TI-designed flexibility permits this signal to fit wide platform
requirements. RI_OUT on the PCI7410 device can be asserted under any of the following conditions:
•
A 16-bit PC Card modem in a powered socket asserts RI to indicate to the system the presence of an
incoming call.
•
A powered down CardBus card asserts CSTSCHG (CBWAKE) requesting system and interface wake-up.
•
A powered CardBus card asserts CSTSCHG from the insertion/removal of cards or change in battery
voltage levels.
3–27
Figure 3–17 shows various enable bits for the PCI7410 RI_OUT function; however, it does not show the masking of
CSC events. See Table 3–15 for a detailed description of CSC interrupt masks and flags.
RI_OUT Function
CSTSMASK
PC Card
Socket
RIENB
CSC
Card
I/F
RINGEN
RI_OUT
RI
CDRESUME
CSC
Figure 3–17. RI_OUT Functional Diagram
RI from the 16-bit PC Card interface is masked by bit 7 (RINGEN) in the ExCA interrupt and general control register
(ExCA offset 03h/43h/803h, see Section 5.4). This is programmed on a per-socket basis and is only applicable when
a 16-bit card is powered in the socket.
The CBWAKE signaling to RI_OUT is enabled through the same mask as the CSC event for CSTSCHG. The mask
bit (bit 0, CSTSMASK) is programmed through the socket mask register (CB offset 04h, see Section 6.2) in the
CardBus socket registers.
RI_OUT can be routed through any of three different pins, RI_OUT/PME, MFUNC2, or MFUNC4. The RI_OUT
function is enabled by setting bit 7 (RIENB) in the card control register (PCI offset 91h, see Section 4.39). The PME
function is enabled by setting bit 8 (PME_ENABLE) in the power-management control/status register (PCI offset A4h,
see Section 4.45). When bit 0 (RIMUX) in the system control register (PCI offset 80h, see Section 4.30) is set to 0,
both the RI_OUT function and the PME function are routed to the RI_OUT/PME terminal. If both functions are enabled
and RIMUX is set to 0, then the RI_OUT/PME terminal becomes RI_OUT only and PME assertions are never seen.
Therefore, in a system using both the RI_OUT function and the PME function, RIMUX must be set to 1 and RI_OUT
must be routed to either MFUNC2 or MFUNC4.
3.9.9
PCI Power Management for CardBus (Function 0)
The PCI Bus Power Management Interface Specification for PCI to CardBus Bridges establishes the infrastructure
required to let the operating system control the power of PCI functions. This is done by defining a standard PCI
interface and operations to manage the power of PCI functions on the bus. The PCI bus and the PCI functions can
be assigned one of seven power-management states, resulting in varying levels of power savings.
The seven power-management states of PCI functions are:
•
•
•
•
•
•
•
D0-uninitialized – Before device configuration, device not fully functional
D0-active – Fully functional state
D1 – Low-power state
D2 – Low-power state
D3hot – Low-power state. Transition state before D3cold
D3cold – PME signal-generation capable. Main power is removed and VAUX is available.
D3off – No power and completely nonfunctional
NOTE 1: In the D0-uninitialized state, the PCI7410 device does not generate PME and/or interrupts. When bits 0 (IO_EN) and 1 (MEM_EN) of
the command register (PCI offset 04h, see Section 4.5) are both set, the PCI7410 device switches the state to D0-active. Transition
from D3cold to the D0-uninitialized state happens at the deassertion of PRST. The assertion of GRST forces the controller to the
D0-uninitialized state immediately.
NOTE 2: The PWR_STATE bits (bits 1–0) of the power-management control/status register (PCI offset A4h, see Section 4.45) only code for four
power states, D0, D1, D2, and D3hot. The differences between the three D3 states is invisible to the software because the controller
is not accessible in the D3cold or D3off state.
Similarly, bus power states of the PCI bus are B0–B3. The bus power states B0–B3 are derived from the device power
state of the originating bridge device.
3–28
For the operating system (OS) to manage the device power states on the PCI bus, the PCI function must support four
power-management operations. These operations are:
•
•
•
•
Capabilities reporting
Power status reporting
Setting the power state
System wake-up
The OS identifies the capabilities of the PCI function by traversing the new capabilities list. The presence of
capabilities in addition to the standard PCI capabilities is indicated by a 1 in bit 4 (CAPLIST) of the status register (PCI
offset 06h, see Section 4.6).
The capabilities pointer provides access to the first item in the linked list of capabilities. For the PCI7410 device, a
CardBus bridge with PCI configuration space header type 2, the capabilities pointer is mapped to an offset of 14h.
The first byte of each capability register block is required to be a unique ID of that capability. PCI power management
has been assigned an ID of 01h. The next byte is a pointer to the next pointer item in the list of capabilities. If there
are no more items in the list, then the next item pointer must be set to 0. The registers following the next item pointer
are specific to the capability of the function. The PCI power-management capability implements the register block
outlined in Table 3–20.
Table 3–20. Power-Management Registers
REGISTER NAME
Power-management capabilities
Data
Power-management control/status register bridge support extensions
OFFSET
Next item pointer
Capability ID
Power-management control/status (CSR)
A0h
A4h
The power-management capabilities register (PCI offset A2h, see Section 4.44) is a static read-only register that
provides information on the capabilities of the function related to power management. The power-management
control/status register (PCI offset A4h, see Section 4.45) enables control of power-management states and
enables/monitors power-management events. The data register is an optional register that can provide dynamic data.
For more information on PCI power management, see the PCI Bus Power Management Interface Specification for
PCI to CardBus Bridges.
3.9.9.1 Function 2 Power Management
The PCI7410 device complies with the PCI Bus Power Management Interface Specification. The device supports the
D0 (unitialized), D0 (active), D1, D2, and D3 power states as defined by the power management definition in the 1394
Open Host Controller Interface Specification, Appendix A4.
Table 3–21. Function 2 Power-Management Registers
REGISTER NAME
Power-management capabilities
Data
Power-management control/status register bridge support extensions
OFFSET
Next item pointer
Capability ID
Power-management control/status (CSR)
44h
48h
3.9.9.2 Function 3 Power Management
The PCI Bus Power Management Interface Specification is applicable for the firmware loader. This function supports
the D0 and D3 power states.
Table 3–22. Function 3 Power-Management Registers
REGISTER NAME
Power-management capabilities
Data
Power-management control/status register bridge support extensions
OFFSET
Next item pointer
Capability ID
Power-management control/status (CSR)
44h
48h
3.9.10 CardBus Bridge Power Management
The PCI Bus Power Management Interface Specification for PCI to CardBus Bridges was approved by PCMCIA in
December of 1997. This specification follows the device and bus state definitions provided in the PCI Bus Power
3–29
Management Interface Specification published by the PCI Special Interest Group (SIG). The main issue addressed
in the PCI Bus Power Management Interface Specification for PCI to CardBus Bridges is wake-up from D3hot or D3cold
without losing wake-up context (also called PME context).
The specific issues addressed by the PCI Bus Power Management Interface Specification for PCI to CardBus Bridges
for D3 wake-up are as follows:
•
Preservation of device context. The specification states that a reset must occur during the transition from
D3 to D0. Some method to preserve wake-up context must be implemented so that the reset does not clear
the PME context registers.
•
Power source in D3cold if wake-up support is required from this state.
The Texas Instruments PCI7410 device addresses these D3 wake-up issues in the following manner:
•
•
Two resets are provided to handle preservation of PME context bits:
–
Global reset (GRST) is used only on the initial boot up of the system after power up. It places the
PCI7410 device in its default state and requires BIOS to configure the device before becoming fully
functional.
–
PCI reset (PRST) has dual functionality based on whether PME is enabled or not. If PME is enabled,
then PME context is preserved. If PME is not enabled, then PRST acts the same as a normal PCI reset.
Please see the master list of PME context bits in Section 3.9.12.
Power source in D3cold if wake-up support is required from this state. Since VCC is removed in D3cold, an
auxiliary power source must be supplied to the PCI7410 VCC terminals. Consult the PCI14xx
Implementation Guide for D3 Wake-Up or the PCI Power Management Interface Specification for PCI to
CardBus Bridges for further information.
3.9.11 ACPI Support
The Advanced Configuration and Power Interface (ACPI) Specification provides a mechanism that allows unique
pieces of hardware to be described to the ACPI driver. The PCI7410 device offers a generic interface that is compliant
with ACPI design rules.
Two doublewords of general-purpose ACPI programming bits reside in PCI7410 PCI configuration space at offset
88h. The programming model is broken into status and control functions. In compliance with ACPI, the top level event
status and enable bits reside in the general-purpose event status register (PCI offset 88h, see Section 4.33) and
general-purpose event enable register (PCI offset 89h, see Section 4.34). The status and enable bits are
implemented as defined by ACPI and illustrated in Figure 3–18.
Status Bit
Event Input
Enable Bit
Event Output
Figure 3–18. Block Diagram of a Status/Enable Cell
The status and enable bits generate an event that allows the ACPI driver to call a control method associated with the
pending status bit. The control method can then control the hardware by manipulating the hardware control bits or
by investigating child status bits and calling their respective control methods. A hierarchical implementation would
be somewhat limiting, however, as upstream devices would have to remain in some level of power state to report
events.
For more information of ACPI, see the Advanced Configuration and Power Interface (ACPI) Specification.
3.9.12 Master List of PME Context Bits and Global Reset-Only Bits
PME context bit means that the bit is cleared only by the assertion of GRST when the PME enable bit, bit 8 of the
power management control/status register (PCI offset A4h, see Section 4.45) is set. If PME is not enabled, then these
bits are cleared when either PRST or GRST is asserted.
3–30
The PME context bits (functions 0 and 1) are:
•
•
•
•
•
•
•
•
•
•
•
•
Bridge control register (PCI offset 3Eh, see Section 4.26): bit 6
System control register (PCI offset 80h, see Section 4.30): bits 10–8
Power management control/status register (PCI offset A4h, see Section 4.45): bit 15
ExCA power control register (ExCA 802h/842h, see Section 5.3): bits 7, 5 (82365SL mode only), 4–3, 1–0
ExCA interrupt and general control (ExCA 803h/843h, see Section 5.4): bits 6, 5
ExCA card status-change register (ExCA 804h/844h, see Section 5.5): bits 3–0
ExCA card status-change interrupt configuration register (ExCA 805h/845h, see Section 5.6): bits 3–0
ExCA card detect and general control register (ExCA 816h, see Section 5.19): bits 7–6
Socket event register (CardBus offset 00h, see Section 6.1): bits 3–0
Socket mask register (CardBus offset 04h, see Section 6.2): bits 3–0
Socket present state register (CardBus offset 08h, see Section 6.3): bits 27, 13–7, 5–1
Socket control register (CardBus offset 10h, see Section 6.5): bits 6–4, 2–0
Global reset-only bits, as the name implies, are cleared only by GRST. These bits are never cleared by PRST,
regardless of the setting of the PME enable bit. The GRST signal is gated only by the SUSPEND signal. This means
that assertion of SUSPEND blocks the GRST signal internally, thus preserving all register contents. Figure 3–15 is
a diagram showing the application of GRST and PRST.
The global reset-only bits (functions 0 and 1) are:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Status register (PCI offset 06h, see Section 4.6): bits 15–11, 8
Secondary status register (PCI offset 16h, see Section 4.15): bits 15–11, 8
Subsystem vendor ID register (PCI offset 40h, see Section 4.27): bits 15–0
Subsystem ID register (PCI offset 42h, see Section 4.28): bits 15–0
PC Card 16-bit I/F legacy-mode base-address register (PCI offset 44h, see Section 4.29): bits 31–0
System control register (PCI offset 80h, see Section 4.30): bits 31–24, 22–13, 11, 6–0
UM_CD debounce register (PCI offset 84h, see Section 4.31): bits 7–0
General control register (PCI offset 86h, see Section 4.32): bits 15–10, 7, 5–3, 1–0
General-purpose event status register (PCI offset 88h, see Section 4.33): bits 7–6, 4–0
General-purpose event enable register (PCI offset 89h, see Section 4.34): bits 7–6, 4–0
General-purpose output register (PCI offset 8Bh, see Section 4.36): bits 4–0
Multifunction routing register (PCI offset 8Ch, see Section 4.37): bits 31–0
Retry status register (PCI offset 90h, see Section 4.38): bits 7–5, 3, 1
Card control register (PCI offset 91h, see Section 4.39): bits 7–5, 2–0
Device control register (PCI offset 92h, see Section 4.40): bits 7–5, 3–0
Diagnostic register (PCI offset 93h, see Section 4.41): bits 7–0
Power management capabilities register (PCI offset A2h, see Section 4.44): bit 15
Power management CSR register (PCI offset A4h, see Section 4.45): bit 8
Serial bus data register (PCI offset B0h, see Section 4.48): bits 7–0
Serial bus index register (PCI offset B1h, see Section 4.49): bits 7–0
Serial bus slave address register (PCI offset B2h, see Section 4.50): bits 7–0
Serial bus control/status register (PCI offset B3h, see Section 4.51): bits 7, 3–0
ExCA identification and revision register (ExCA 800h, see Section 5.1): bits 7–0
ExCA global control register (ExCA 81Eh, see Section 5.20): bits 2–0
CardBus socket power management register (CardBus 20h, see Section 6.6): bits 25–24
The global reset-only bit (function 2) is:
•
•
•
•
•
•
Subsystem vendor ID register (PCI offset 2Ch, see Section 7.12): bits 15–0
Subsystem ID register (PCI offset 2Eh, see Section 7.12): bits 31–16
Minimum grant and maximum latency register (PCI offset 3Eh, see Section 7.16): bits 15–0
Power management control and status register (PCI offset 48h, see Section 7.20): bits 15, 8, 1, 0
PCI PHY control register (PCI offset ECh, see Section 7.22): bits 7, 4–0
Miscellaneous configuration register (PCI offset F0h, see Section 7.23): bits 15, 11–8, 5–0
3–31
•
•
•
•
•
•
•
•
Link enhancement control register (PCI offset F4h, see Section 7.24): bits 15–12, 10, 8–7, 2–1
Bus options register (OHCI offset 20h, see Section 8.9): bits 15–12
GUID high register (OHCI offset 24h, see Section 8.10): bits 31–0
GUID low register (OHCI offset 28h, see Section 8.11): bits 31–0
Host controller control register (OHCI offset 50h/54h, see Section 8.16): bit 23
Link control register (OHCI offset E0h/E4h, see Section 8.31): bit 6
PHY-link loopback test register (Local offset C14h): bits 6–4, 0
Link test control register (Local offset C00h): bits 12–8
The global reset-only (function 3) register bits:
•
•
•
•
Subsystem vendor ID register (PCI offset 2Ch, see Section 7.12): bits 15–0
Subsystem ID register (PCI offset 2Eh, see Section 7.12): bits 31–16
Power management control and status register (PCI offset 48h, see Section 7.20): bits 1, 0
Miscellaneous control register (PCI offset 50h, see Section ): bit 0
3.10 IEEE 1394 Application Information
3.10.1 PHY Port Cable Connection
PCI7410
400 kΩ
CPS
1 µF
Cable
Power
Pair
TPBIAS
56 Ω
56 Ω
TPA+
Cable
Pair
A
TPA–
Cable Port
TPB+
Cable
Pair
B
TPB–
56 Ω
220 pF
(see Note A)
56 Ω
5 kΩ
Outer Shield
Termination
NOTE A: IEEE Std 1394-1995 calls for a 250-pF capacitor, which is a nonstandard component value. A 220-pF capacitor is recommended.
Figure 3–19. TP Cable Connections
3–32
Outer Cable Shield
0.01 µF
1 MΩ
0.001 µF
Chassis Ground
Figure 3–20. Typical Compliant DC Isolated Outer Shield Termination
Outer Cable Shield
Chassis Ground
Figure 3–21. Non-DC Isolated Outer Shield Termination
3.10.2 Crystal Selection
The PCI7410 device is designed to use an external 24.576-MHz crystal connected between the XI and XO terminals
to provide the reference for an internal oscillator circuit. This oscillator in turn drives a PLL circuit that generates the
various clocks required for transmission and resynchronization of data at the S100 through S400 media data rates.
A variation of less than ±100 ppm from nominal for the media data rates is required by IEEE Std 1394-1995. Adjacent
PHYs may therefore have a difference of up to 200 ppm from each other in their internal clocks, and PHY devices
must be able to compensate for this difference over the maximum packet length. Large clock variations may cause
resynchronization overflows or underflows, resulting in corrupted packet data.
The following are some typical specifications for crystals used with the PHYs from TI in order to achieve the required
frequency accuracy and stability:
•
Crystal mode of operation: Fundamental
•
Frequency tolerance @ 25°C: Total frequency variation for the complete circuit is ±100 ppm. A crystal with
±30 ppm frequency tolerance is recommended for adequate margin.
•
Frequency stability (over temperature and age): A crystal with ±30 ppm frequency stability is recommended
for adequate margin.
NOTE: The total frequency variation must be kept below ±100 ppm from nominal with some
allowance for error introduced by board and device variations. Trade-offs between frequency
tolerance and stability may be made as long as the total frequency variation is less than
±100 ppm. For example, the frequency tolerance of the crystal may be specified at 50 ppm and
the temperature tolerance may be specified at 30 ppm to give a total of 80 ppm possible
variation due to the crystal alone. Crystal aging also contributes to the frequency variation.
•
Load capacitance: For parallel resonant mode crystal circuits, the frequency of oscillation is dependent
upon the load capacitance specified for the crystal. Total load capacitance (CL) is a function of not only the
discrete load capacitors, but also board layout and circuit. It is recommended that load capacitors with a
maximum of ±5% tolerance be used.
3–33
For example, load capacitors (C9 and C10 in Figure 3–22) of 16 pF each were appropriate for the layout of the
PCI7410 evaluation module (EVM), which uses a crystal specified for 12-pF loading. The load specified for the crystal
includes the load capacitors (C9 and C10), the loading of the PHY pins (CPHY), and the loading of the board itself
(CBD). The value of CPHY is typically about 1 pF, and CBD is typically 0.8 pF per centimeter of board etch; a typical
board can have 3 pF to 6 pF or more. The load capacitors C9 and C10 combine as capacitors in series so that the
total load capacitance is:
C L + C9 C10 ) C PHY ) C BD
C9 ) C10
C9
X1
X1
24.576 MHz
IS
CPHY + CBD
X0
C10
Figure 3–22. Load Capacitance for the PCI7410 PHY
The layout of the crystal portion of the PHY circuit is important for obtaining the correct frequency, minimizing noise
introduced into the PHY phase-lock loop, and minimizing any emissions from the circuit. The crystal and two load
capacitors must be considered as a unit during layout. The crystal and the load capacitors must be placed as close
as possible to one another while minimizing the loop area created by the combination of the three components.
Varying the size of the capacitors may help in this. Minimizing the loop area minimizes the effect of the resonant
current (Is) that flows in this resonant circuit. This layout unit (crystal and load capacitors) must then be placed as
close as possible to the PHY X1 and X0 terminals to minimize etch lengths, as shown in Figure 3–23.
C9
C10
X1
For more details on crystal selection, see application report SLLA051 available from the TI website:
http://www.ti.com/sc/1394.
Figure 3–23. Recommended Crystal and Capacitor Layout
3.10.3 Bus Reset
In the PCI7410 device, the initiate bus reset (IBR) bit may be set to 1 in order to initiate a bus reset and initialization
sequence. The IBR bit is located in PHY register 1, along with the root-holdoff bit (RHB) and Gap_Count field, as
required by IEEE Std 1394a-2000. Therefore, whenever the IBR bit is written, the RHB and Gap_Count are also
written.
The RHB and Gap_Count may also be updated by PHY-config packets. The PCI7410 device is IEEE 1394a-2000
compliant, and therefore both the reception and transmission of PHY-config packets cause the RHB and Gap_Count
to be loaded, unlike older IEEE 1394-1995 compliant PHY devices which decode only received PHY-config packets.
The gap-count is set to the maximum value of 63 after 2 consecutive bus resets without an intervening write to the
Gap_Count, either by a write to PHY register 1 or by a PHY-config packet. This mechanism allows a PHY-config
3–34
packet to be transmitted and then a bus reset initiated so as to verify that all nodes on the bus have updated their
RHBs and Gap_Count values, without having the Gap_Count set back to 63 by the bus reset. The subsequent
connection of a new node to the bus, which initiates a bus reset, then causes the Gap_Count of each node to be set
to 63. Note, however, that if a subsequent bus reset is instead initiated by a write to register 1 to set the IBR bit, all
other nodes on the bus have their Gap_Count values set to 63, while this node Gap_Count remains set to the value
just loaded by the write to PHY register 1.
Therefore, in order to maintain consistent gap-counts throughout the bus, the following rules apply to the use of the
IBR bit, RHB, and Gap_Count in PHY register 1:
•
Following the transmission of a PHY-config packet, a bus reset must be initiated in order to verify that all
nodes have correctly updated their RHBs and Gap_Count values and to ensure that a subsequent new
connection to the bus causes the Gap_Count to be set to 63 on all nodes in the bus. If this bus reset is
initiated by setting the IBR bit to 1, then the RHB and Gap_Count field must also be loaded with the correct
values consistent with the just transmitted PHY-config packet. In the PCI7410 device, the RHB and
Gap_Count are updated to their correct values upon the transmission of the PHY-config packet, so these
values may first be read from register 1 and then rewritten.
•
Other than to initiate the bus reset, which must follow the transmission of a PHY-config packet, whenever
the IBR bit is set to 1 in order to initiate a bus reset, the Gap_Count value must also be set to 63 so as to
be consistent with other nodes on the bus, and the RHB must be maintained with its current value.
•
The PHY register 1 must not be written to except to set the IBR bit. The RHB and Gap_Count must not be
written without also setting the IBR bit to 1.
3–35
3–36
4 PC Card Controller Programming Model
This chapter describes the PCI7410 PCI configuration registers that make up the 256-byte PCI configuration header
for each PCI7410 function. There are some bits which affect both CardBus functions, but which, in order to work
properly, must be accessed only through function 0. These are called global bits. Registers containing one or more
global bits are denoted by § in Table 4–2.
Any bit followed by a † is not cleared by the assertion of PRST (see CardBus Bridge Power Management,
Section 3.9.10, for more details) if PME is enabled (PCI offset A4h, bit 8). In this case, these bits are cleared only by
GRST. If PME is not enabled, then these bits are cleared by GRST or PRST. These bits are sometimes referred to
as PME context bits and are implemented to allow PME context to be preserved during the transition from D3hot or
D3cold to D0.
If a bit is followed by a ‡, then this bit is cleared only by GRST in all cases (not conditional on PME being enabled).
These bits are intended to maintain device context such as interrupt routing and MFUNC programming during warm
resets.
A bit description table, typically included when the register contains bits of more than one type or purpose, indicates
bit field names, a detailed field description, and field access tags which appear in the type column. Table 4–1
describes the field access tags.
Table 4–1. Bit Field Access Tag Descriptions
ACCESS TAG
NAME
R
Read
Field can be read by software.
MEANING
W
Write
Field can be written by software to any value.
S
Set
Field can be set by a write of 1. Writes of 0 have no effect.
C
Clear
U
Update
Field can be cleared by a write of 1. Writes of 0 have no effect.
Field can be autonomously updated by the PCI7410 device.
4.1 PCI Configuration Registers (Functions 0 and 1)
The PCI7410 is a multifunction PCI device, and the PC Card controller is integrated as PCI functions 0 and 1. The
configuration header, compliant with the PCI Local Bus Specification as a CardBus bridge header, is PC99/PC2001
compliant as well. Table 4–2 illustrates the PCI configuration register map, which includes both the predefined portion
of the configuration space and the user-definable registers.
Table 4–2. Functions 0 and 1 PCI Configuration Register Map
REGISTER NAME
OFFSET
Device ID
Vendor ID
Status ‡
00h
Command
Class code
BIST
Header type
Latency timer
04h
Revision ID
08h
Cache line size
0Ch
CardBus socket registers/ExCA base address register
Secondary status ‡
CardBus latency timer
Subordinate bus number
10h
Reserved
Capability pointer
CardBus bus number
PCI bus number
14h
18h
CardBus memory base register 0
1Ch
CardBus memory limit register 0
20h
CardBus memory base register 1
24h
CardBus memory limit register 1
28h
‡ One or more bits in this register are cleared only by the assertion of GRST.
4–1
Table 4–2. Functions 0 and 1 PCI Configuration Register Map (Continued)
REGISTER NAME
OFFSET
CardBus I/O base register 0
2Ch
CardBus I/O limit register 0
30h
CardBus I/O base register 1
34h
CardBus I/O limit register 1
Bridge control †
38h
Interrupt pin
Subsystem ID ‡
Interrupt line
3Ch
Subsystem vendor ID ‡
40h
PC Card 16-bit I/F legacy-mode base-address ‡
44h
Reserved
48h–7Ch
System control †‡§
General control ‡§
General-purpose output ‡
General-purpose input
Diagnostic ‡§
Device control ‡§
80h
Reserved
UM_CD debounce ‡
84h
General-purpose event
enable ‡
General-purpose event
status ‡
88h
Multifunction routing status ‡
8Ch
Card control ‡§
Retry status ‡§
90h
Reserved
Power management capabilities ‡
94h–9Ch
Next item pointer
Power management data
(Reserved)
Power management
control/status bridge support
extensions
Serial bus control/status ‡
Serial bus slave address ‡
Capability ID
A0h
A4h
Power management control/status †‡
Reserved
A8h–ACh
Serial bus index ‡
Serial bus data ‡
B0h
Reserved
B4h–FCh
† One or more bits in this register are PME context bits and can be cleared only by the assertion of GRST when PME is enabled. If PME is not
enabled, then this bit is cleared by the assertion of PRST or GRST.
‡ One or more bits in this register are cleared only by the assertion of GRST.
§ One or more bits in this register are global in nature and must be accessed only through function 0.
4.2 Vendor ID Register
The vendor ID register contains a value allocated by the PCI SIG that identifies the manufacturer of the PCI device.
The vendor ID assigned to Texas Instruments is 104Ch.
Bit
15
14
13
12
11
10
9
Name
8
7
6
5
4
3
2
1
0
Vendor ID
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
1
0
0
0
0
0
1
0
0
1
1
0
0
Register:
Offset:
Type:
Default:
4–2
Vendor ID
00h (Functions 0, 1)
Read-only
104Ch
4.3 Device ID Register Function 0
The device ID register contains a value assigned to the PCI7410 device by Texas Instruments. The device
identification for the PCI7410 device is AC49h.
Bit
15
14
13
12
11
10
9
8
Name
7
6
5
4
3
2
1
0
Device ID
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
1
0
1
0
1
1
0
0
0
1
0
0
1
0
0
1
Register:
Offset:
Type:
Default:
Device ID
02h (Function 0)
Read-only
AC49h
4.4 Device ID Register Function 1
This read-only register contains the device ID assigned by TI to the PCI7410 dedicated socket function (PCI function
1). When the dedicated socket is SD/MMC, the device ID is AC4Bh. When the dedicated socket is Memory Stick, the
device ID is AC4Ch.
Bit
15
14
13
12
11
10
9
Type
R
R
R
R
R
R
R
R
Default
1
0
1
0
1
1
0
0
8
Name
7
6
5
4
3
2
1
0
R
R
R
R
R
R
R
R
0
1
0
0
1
0
1
1
7
6
5
4
3
2
1
0
Device ID—SD/MMC
Register:
Offset:
Type:
Default:
Bit
8
15
14
Device ID (dedicated SD/MMC)
02h (Function 1)
Read-only
AC4Bh
13
12
11
10
Name
9
Device ID—Memory Stick
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
1
0
1
0
1
1
0
0
0
1
0
0
1
1
0
0
Register:
Offset:
Type:
Default:
Device ID (dedicated Memory Stick)
02h (Function 1)
Read-only
AC4Ch
4–3
4.5 Command Register
The PCI command register provides control over the PCI7410 interface to the PCI bus. All bit functions adhere to the
definitions in the PCI Local Bus Specification (see Table 4–3). None of the bit functions in this register are shared
among the PCI7410 PCI functions. Three command registers exist in the PCI7410 device, one for each function.
Software manipulates the PCI7410 functions as separate entities when enabling functionality through the command
register. The SERR_EN and PERR_EN enable bits in this register are internally wired OR between the three
functions, and these control bits appear to software to be separate for each function.
Bit
15
14
13
12
11
10
9
Name
8
7
6
5
4
3
2
1
0
Command
Type
R
R
R
R
R
RW
R
RW
R
RW
RW
R
R
RW
RW
RW
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Command
04h
Read-only, Read/Write
0000h
Table 4–3. Command Register Description
BIT
SIGNAL
TYPE
15–11
RSVD
R
10
INT_DISABLE
RW
FUNCTION
Reserved. Bits 15–11 return 0s when read.
INTx disable. When set to 1, this bit disables the function from asserting interrupts on the INTx signals.
0 = INTx assertion is enabled (default)
1 = INTx assertion is disabled
This bit is disabled (read-only 0) if bit 7 (PCI2_3_EN) in the general control register (PCI offset 86h, see
Section 4.32) is 0.
9
R
Fast back-to-back enable. The PCI7410 device does not generate fast back-to-back transactions;
therefore, this bit is read-only. This bit returns a 0 when read.
System error (SERR) enable. This bit controls the enable for the SERR driver on the PCI interface. SERR
can be asserted after detecting an address parity error on the PCI bus. Both this bit and bit 6 must be set
for the PCI7410 device to report address parity errors.
0 = Disables the SERR output driver (default)
1 = Enables the SERR output driver
8
SERR_EN
RW
7
RSVD
R
Reserved. Bit 7 returns 0 when read.
6
PERR_EN
RW
Parity error response enable. This bit controls the PCI7410 response to parity errors through the PERR
signal. Data parity errors are indicated by asserting PERR, while address parity errors are indicated by
asserting SERR.
0 = PCI7410 device ignores detected parity errors (default).
1 = PCI7410 device responds to detected parity errors.
5
VGA_EN
RW
VGA palette snoop. When set to 1, palette snooping is enabled (i.e., the PCI7410 device does not respond
to palette register writes and snoops the data). When the bit is 0, the PCI7410 device treats all palette
accesses like all other accesses.
4
MWI_EN
R
Memory write-and-invalidate enable. This bit controls whether a PCI initiator device can generate memory
write-and-invalidate commands. The PCI7410 controller does not support memory write-and-invalidate
commands, it uses memory write commands instead; therefore, this bit is hardwired to 0. This bit returns
0 when read. Writes to this bit have no effect.
3
SPECIAL
R
Special cycles. This bit controls whether or not a PCI device ignores PCI special cycles. The PCI7410
device does not respond to special cycle operations; therefore, this bit is hardwired to 0. This bit returns
0 when read. Writes to this bit have no effect.
RW
Bus master control. This bit controls whether or not the PCI7410 device can act as a PCI bus initiator
(master). The PCI7410 device can take control of the PCI bus only when this bit is set.
0 = Disables the PCI7410 ability to generate PCI bus accesses (default)
1 = Enables the PCI7410 ability to generate PCI bus accesses
2
4–4
FBB_EN
MAST_EN
Table 4–3. Command Register Description (continued)
BIT
SIGNAL
TYPE
FUNCTION
1
MEM_EN
RW
Memory space enable. This bit controls whether or not the PCI7410 device can claim cycles in PCI memory
space.
0 = Disables the PCI7410 response to memory space accesses (default)
1 = Enables the PCI7410 response to memory space accesses
0
IO_EN
RW
I/O space control. This bit controls whether or not the PCI7410 device can claim cycles in PCI I/O space.
0 = Disables the PCI7410 device from responding to I/O space accesses (default)
1 = Enables the PCI7410 device to respond to I/O space accesses
4.6 Status Register
The status register provides device information to the host system. Bits in this register can be read normally. A bit
in the status register is reset when a 1 is written to that bit location; a 0 written to a bit location has no effect. All bit
functions adhere to the definitions in the PCI Bus Specification, as seen in the bit descriptions. PCI bus status is shown
through each function. See Table 4–4 for a complete description of the register contents.
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RW
RW
RW
RW
RW
R
R
RW
R
R
R
R
R
R
R
R
0
0
0
0
0
0
1
0
0
0
0
1
0
0
0
0
Name
Type
Default
Status
Register:
Offset:
Type:
Default:
Status
06h (Functions 0, 1)
Read-only, Read/Write
0210h
Table 4–4. Status Register Description
BIT
SIGNAL
TYPE
FUNCTION
15 ‡
PAR_ERR
RW
Detected parity error. This bit is set when a parity error is detected, either an address or data parity error.
Write a 1 to clear this bit.
14 ‡
SYS_ERR
RW
Signaled system error. This bit is set when SERR is enabled and the PCI7410 device signaled a system error
to the host. Write a 1 to clear this bit.
13 ‡
MABORT
RW
Received master abort. This bit is set when a cycle initiated by the PCI7410 device on the PCI bus has been
terminated by a master abort. Write a 1 to clear this bit.
12 ‡
TABT_REC
RW
Received target abort. This bit is set when a cycle initiated by the PCI7410 device on the PCI bus was
terminated by a target abort. Write a 1 to clear this bit.
11 ‡
TABT_SIG
RW
Signaled target abort. This bit is set by the PCI7410 device when it terminates a transaction on the PCI bus
with a target abort. Write a 1 to clear this bit.
10–9
PCI_SPEED
R
DEVSEL timing. These bits encode the timing of DEVSEL and are hardwired to 01b indicating that the
PCI7410 device asserts this signal at a medium speed on nonconfiguration cycle accesses.
Data parity error detected. Write a 1 to clear this bit.
0 = The conditions for setting this bit have not been met.
1 = A data parity error occurred and the following conditions were met:
a. PERR was asserted by any PCI device including the PCI7410.
b. The PCI7410 device was the bus master during the data parity error.
c. The parity error response bit is set in the command register.
8‡
DATAPAR
RW
7
FBB_CAP
R
Fast back-to-back capable. The PCI7410 device cannot accept fast back-to-back transactions; thus, this
bit is hardwired to 0.
6
UDF
R
UDF supported. The PCI7410 device does not support user-definable features; therefore, this bit is
hardwired to 0.
5
66MHZ
R
66-MHz capable. The PCI7410 device operates at a maximum PCLK frequency of 33 MHz; therefore, this
bit is hardwired to 0.
‡ One or more bits in this register are cleared only by the assertion of GRST.
4–5
Table 4–4. Status Register Description (continued)
BIT
SIGNAL
TYPE
FUNCTION
4
CAPLIST
R
Capabilities list. This bit returns 1 when read. This bit indicates that capabilities in addition to standard PCI
capabilities are implemented. The linked list of PCI power-management capabilities is implemented in this
function.
3
INT_STATUS
R
Interrupt status. This bit reflects the interrupt status of the function. Only when bit 10 (INT_DISABLE) in the
command register (PCI offset 04h, see Section 4.5) is a 0 and this bit is a 1, will the function’s INTx signal
be asserted. Setting the INT_DISABLE bit to a 1 has no effect on the state of this bit. This bit is disabled
(read-only 0) if bit 7 (PCI2_3_EN) in the general control register (PCI offset 86h, see Section 4.32) is 0.
2–0
RSVD
R
Reserved. These bits return 0s when read.
4.7 Revision ID Register
The revision ID register indicates the silicon revision of the PCI7410 device.
Bit
7
6
5
4
Name
3
2
1
0
Revision ID
Type
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Revision ID
08h (functions 0, 1)
Read-only
00h
4.8 Class Code Register
The class code register recognizes PCI7410 functions 0 and 1 as a bridge device (06h) and a CardBus bridge device
(07h), with a 00h programming interface.
Bit
23
22
21
20
19
18
17
16
15
14
13
Name
12
11
10
9
8
7
6
5
4
3
2
1
0
PCI class code
Base class
Subclass
Programming interface
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
1
1
0
0
0
0
0
0
1
1
1
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
PCI class code
09h (functions 0, 1)
Read-only
06 0700h
4.9 Cache Line Size Register
The cache line size register is programmed by host software to indicate the system cache line size.
Bit
7
6
5
Name
Type
Default
3
2
1
0
Cache line size
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
4–6
4
Cache line size
0Ch (Functions 0, 1)
Read/Write
00h
4.10 Latency Timer Register
The latency timer register specifies the latency timer for the PCI7410 device, in units of PCI clock cycles. When the
PCI7410 device is a PCI bus initiator and asserts FRAME, the latency timer begins counting from zero. If the latency
timer expires before the PCI7410 transaction has terminated, then the PCI7410 device terminates the transaction
when its GNT is deasserted.
Bit
7
6
5
4
Name
Type
Default
3
2
1
0
Latency timer
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Latency timer
0Dh
Read/Write
00h
4.11 Header Type Register
The header type register returns 82h when read, indicating that the PCI7410 functions 0 and 1 configuration spaces
adhere to the CardBus bridge PCI header. The CardBus bridge PCI header ranges from PCI registers 00h–7Fh, and
80h–FFh is user-definable extension registers.
Bit
7
6
5
4
Name
3
2
1
0
Header type
Type
R
R
R
R
R
R
R
R
Default
1
0
0
0
0
0
1
0
Register:
Offset:
Type:
Default:
Header type
0Eh (Functions 0, 1)
Read-only
82h
4.12 BIST Register
Because the PCI7410 device does not support a built-in self-test (BIST), this register returns the value of 00h when
read.
Bit
7
6
5
4
3
2
1
0
Type
R
R
R
R
Default
0
0
0
R
R
R
R
0
0
0
0
0
Name
BIST
Register:
Offset:
Type:
Default:
BIST
0Fh (Functions 0, 1)
Read-only
00h
4–7
4.13 CardBus Socket Registers/ExCA Base Address Register
This register is programmed with a base address referencing the CardBus socket registers and the memory-mapped
ExCA register set. Bits 31–12 are read/write, and allow the base address to be located anywhere in the 32-bit PCI
memory address space on a 4-Kbyte boundary. Bits 11–0 are read-only, returning 0s when read. When software
writes all 1s to this register, the value read back is FFFF F000h, indicating that at least 4K bytes of memory address
space are required. The CardBus registers start at offset 000h, and the memory-mapped ExCA registers begin at
offset 800h. This register is not shared by functions 0 and 1, so the system maps each socket control register
separately.
Bit
31
30
29
28
27
26
Name
Type
25
24
23
22
21
20
19
18
17
16
CardBus socket registers/ExCA base address
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
CardBus socket registers/ExCA base address
RW
RW
RW
RW
R
R
R
R
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
CardBus socket registers/ExCA base address
10h
Read-only, Read/Write
0000 0000h
4.14 Capability Pointer Register
The capability pointer register provides a pointer into the PCI configuration header where the PCI power management
register block resides. PCI header doublewords at A0h and A4h provide the power management (PM) registers. Each
socket has its own capability pointer register. This register is read-only and returns A0h when read.
Bit
7
6
5
Name
4
3
2
1
0
Capability pointer
Type
R
R
R
R
R
R
R
R
Default
1
0
1
0
0
0
0
0
Register:
Offset:
Type:
Default:
4–8
Capability pointer
14h
Read-only
A0h
4.15 Secondary Status Register
The secondary status register is compatible with the PCI-PCI bridge secondary status register. It indicates
CardBus-related device information to the host system. This register is very similar to the PCI status register (PCI
offset 06h, see Section 4.6), and status bits are cleared by a writing a 1. This register is not shared by the two socket
functions, but is accessed on a per-socket basis. See Table 4–5 for a complete description of the register contents.
Bit
15
14
13
12
11
10
9
Name
Type
Default
8
7
6
5
4
3
2
1
0
Secondary status
RC
RC
RC
RC
RC
R
R
RC
R
R
R
R
R
R
R
R
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Secondary status
16h
Read-only, Read/Clear
0200h
Table 4–5. Secondary Status Register Description
BIT
SIGNAL
TYPE
FUNCTION
15 ‡
CBPARITY
RC
Detected parity error. This bit is set when a CardBus parity error is detected, either an address or data
parity error. Write a 1 to clear this bit.
14 ‡
CBSERR
RC
Signaled system error. This bit is set when CSERR is signaled by a CardBus card. The PCI7410 device
does not assert the CSERR signal. Write a 1 to clear this bit.
13 ‡
CBMABORT
RC
Received master abort. This bit is set when a cycle initiated by the PCI7410 device on the CardBus bus
is terminated by a master abort. Write a 1 to clear this bit.
12 ‡
REC_CBTA
RC
Received target abort. This bit is set when a cycle initiated by the PCI7410 device on the CardBus bus
is terminated by a target abort. Write a 1 to clear this bit.
11 ‡
SIG_CBTA
RC
Signaled target abort. This bit is set by the PCI7410 device when it terminates a transaction on the
CardBus bus with a target abort. Write a 1 to clear this bit.
10–9
CB_SPEED
R
CDEVSEL timing. These bits encode the timing of CDEVSEL and are hardwired to 01b indicating that the
PCI7410 device asserts this signal at a medium speed.
CardBus data parity error detected. Write a 1 to clear this bit.
0 = The conditions for setting this bit have not been met.
1 = A data parity error occurred and the following conditions were met:
a. CPERR was asserted on the CardBus interface.
b. The PCI7410 device was the bus master during the data parity error.
c. The parity error response enable bit (bit 0) is set in the bridge control register (PCI offset 3Eh,
see Section 4.26).
8‡
CB_DPAR
RC
7
CBFBB_CAP
R
Fast back-to-back capable. The PCI7410 device cannot accept fast back-to-back transactions; therefore,
this bit is hardwired to 0.
6
CB_UDF
R
User-definable feature support. The PCI7410 device does not support user-definable features; therefore,
this bit is hardwired to 0.
5
CB66MHZ
R
66-MHz capable. The PCI7410 CardBus interface operates at a maximum CCLK frequency of 33 MHz;
therefore, this bit is hardwired to 0.
4–0
RSVD
R
These bits return 0s when read.
‡ One or more bits in this register are cleared only by the assertion of GRST.
4–9
4.16 PCI Bus Number Register
The PCI bus number register is programmed by the host system to indicate the bus number of the PCI bus to which
the PCI7410 device is connected. The PCI7410 device uses this register in conjunction with the CardBus bus number
and subordinate bus number registers to determine when to forward PCI configuration cycles to its secondary buses.
Bit
7
6
5
Name
Type
Default
4
3
2
1
0
PCI bus number
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
PCI bus number
18h (Functions 0, 1)
Read/Write
00h
4.17 CardBus Bus Number Register
The CardBus bus number register is programmed by the host system to indicate the bus number of the CardBus bus
to which the PCI7410 device is connected. The PCI7410 device uses this register in conjunction with the PCI bus
number and subordinate bus number registers to determine when to forward PCI configuration cycles to its secondary
buses. This register is separate for each PCI7410 controller function.
Bit
7
6
5
Name
Type
Default
4
3
2
1
0
CardBus bus number
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
CardBus bus number
19h
Read/Write
00h
4.18 Subordinate Bus Number Register
The subordinate bus number register is programmed by the host system to indicate the highest numbered bus below
the CardBus bus. The PCI7410 device uses this register in conjunction with the PCI bus number and CardBus bus
number registers to determine when to forward PCI configuration cycles to its secondary buses. This register is
separate for each CardBus controller function.
Bit
7
6
5
RW
RW
RW
RW
0
0
0
0
Name
Type
Default
3
2
1
0
RW
RW
RW
RW
0
0
0
0
Subordinate bus number
Register:
Offset:
Type:
Default:
4–10
4
Subordinate bus number
1Ah
Read/Write
00h
4.19 CardBus Latency Timer Register
The CardBus latency timer register is programmed by the host system to specify the latency timer for the PCI7410
CardBus interface, in units of CCLK cycles. When the PCI7410 device is a CardBus initiator and asserts CFRAME,
the CardBus latency timer begins counting. If the latency timer expires before the PCI7410 transaction has
terminated, then the PCI7410 device terminates the transaction at the end of the next data phase. A recommended
minimum value for this register of 20h allows most transactions to be completed.
Bit
7
6
5
4
Name
3
2
1
0
CardBus latency timer
Type
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
Default
Register:
Offset:
Type:
Default:
CardBus latency timer
1Bh (Functions 0, 1)
Read/Write
00h
4.20 CardBus Memory Base Registers 0, 1
These registers indicate the lower address of a PCI memory address range. They are used by the PCI7410 device
to determine when to forward a memory transaction to the CardBus bus, and likewise, when to forward a CardBus
cycle to PCI. Bits 31–12 of these registers are read/write and allow the memory base to be located anywhere in the
32-bit PCI memory space on 4-Kbyte boundaries. Bits 11–0 are read-only and always return 0s. Writes to these bits
have no effect. Bits 8 and 9 of the bridge control register (PCI offset 3Eh, see Section 4.26) specify whether memory
windows 0 and 1 are prefetchable or nonprefetchable. The memory base register or the memory limit register must
be nonzero in order for the PCI7410 device to claim any memory transactions through CardBus memory windows
(i.e., these windows by default are not enabled to pass the first 4 Kbytes of memory to CardBus).
Bit
31
30
29
28
27
26
Name
Type
25
24
23
22
21
20
19
18
17
16
Memory base registers 0, 1
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Memory base registers 0, 1
RW
RW
RW
RW
R
R
R
R
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Memory base registers 0, 1
1Ch, 24h
Read-only, Read/Write
0000 0000h
4–11
4.21 CardBus Memory Limit Registers 0, 1
These registers indicate the upper address of a PCI memory address range. They are used by the PCI7410 device
to determine when to forward a memory transaction to the CardBus bus, and likewise, when to forward a CardBus
cycle to PCI. Bits 31–12 of these registers are read/write and allow the memory base to be located anywhere in the
32-bit PCI memory space on 4-Kbyte boundaries. Bits 11–0 are read-only and always return 0s. Writes to these bits
have no effect. Bits 8 and 9 of the bridge control register (PCI offset 3Eh, see Section 4.26) specify whether memory
windows 0 and 1 are prefetchable or nonprefetchable. The memory base register or the memory limit register must
be nonzero in order for the PCI7410 device to claim any memory transactions through CardBus memory windows
(i.e., these windows by default are not enabled to pass the first 4 Kbytes of memory to CardBus).
Bit
31
30
29
28
27
26
Name
Type
25
24
23
22
21
20
19
18
17
16
Memory limit registers 0, 1
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RW
RW
RW
RW
R
R
R
R
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Name
Type
Default
Memory limit registers 0, 1
Register:
Offset:
Type:
Default:
Memory limit registers 0, 1
20h, 28h
Read-only, Read/Write
0000 0000h
4.22 CardBus I/O Base Registers 0, 1
These registers indicate the lower address of a PCI I/O address range. They are used by the PCI7410 device to
determine when to forward an I/O transaction to the CardBus bus, and likewise, when to forward a CardBus cycle
to the PCI bus. The lower 16 bits of this register locate the bottom of the I/O window within a 64-Kbyte page. The upper
16 bits (31–16) are all 0s, which locates this 64-Kbyte page in the first page of the 32-bit PCI I/O address space. Bits
31–2 are read/write and always return 0s forcing I/O windows to be aligned on a natural doubleword boundary in the
first 64-Kbyte page of PCI I/O address space. Bits 1–0 are read-only, returning 00 or 01 when read, depending on
the value of bit 11 (IO_BASE_SEL) in the general control register (PCI offset 86h, see Section 4.32). These I/O
windows are enabled when either the I/O base register or the I/O limit register is nonzero. The I/O windows by default
are not enabled to pass the first doubleword of I/O to CardBus.
Either the I/O base register or the I/O limit register must be nonzero to enable any I/O transactions.
Bit
31
30
29
28
27
26
25
Name
Type
24
23
22
21
20
19
18
17
16
I/O base registers 0, 1
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
I/O base registers 0, 1
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
R
R
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
X
Register:
Offset:
Type:
Default:
4–12
I/O base registers 0, 1
2Ch, 34h
Read-only, Read/Write
0000 000Xh
4.23 CardBus I/O Limit Registers 0, 1
These registers indicate the upper address of a PCI I/O address range. They are used by the PCI7410 device to
determine when to forward an I/O transaction to the CardBus bus, and likewise, when to forward a CardBus cycle
to PCI. The lower 16 bits of this register locate the top of the I/O window within a 64-Kbyte page, and the upper 16
bits are a page register which locates this 64-Kbyte page in 32-bit PCI I/O address space. Bits 15–2 are read/write
and allow the I/O limit address to be located anywhere in the 64-Kbyte page (indicated by bits 31–16 of the appropriate
I/O base register) on doubleword boundaries.
Bits 31–16 are read-only and always return 0s when read. The page is set in the I/O base register. Bits 15–2 are
read/write and bits 1–0 are read-only, returning 00 or 01 when read, depending on the value of bit 12 (IO_LIMIT_SEL)
in the general control register (PCI offset 86h, see Section 4.32). Writes to read-only bits have no effect.
These I/O windows are enabled when either the I/O base register or the I/O limit register is nonzero. By default, the
I/O windows are not enabled to pass the first doubleword of I/O to CardBus.
Either the I/O base register or the I/O limit register must be nonzero to enable any I/O transactions.
Bit
31
30
29
28
27
26
25
Type
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
Name
Default
23
22
21
20
19
18
17
16
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
7
6
5
4
3
2
1
0
RW
RW
RW
RW
RW
RW
R
R
0
0
0
0
0
0
0
X
I/O limit registers 0, 1
Name
Type
24
I/O limit registers 0, 1
Register:
Offset:
Type:
Default:
I/O limit registers 0, 1
30h, 38h
Read-only, Read/Write
0000 000Xh
4.24 Interrupt Line Register
The interrupt line register is a read/write register used by the host software. As part of the interrupt routing procedure,
the host software writes this register with the value of the system IRQ assigned to the function.
Bit
7
6
5
4
3
2
1
0
RW
RW
RW
RW
RW
RW
RW
RW
1
1
1
1
1
1
1
1
Name
Type
Default
Interrupt line
Register:
Offset:
Type:
Default:
Interrupt line
3Ch
Read/Write
FFh
4–13
4.25 Interrupt Pin Register
The value read from this register is function dependent. The default value for function 0 is 01h (INTA), and the default
value for function 1 is 02h (INTB), and the default value for function 2 is 03h (INTC). The value also depends on the
values of bits 28, the tie-all bit (TIEALL), and 29, the interrupt tie bit (INTRTIE), in the system control register (PCI
offset 80h, see Section 4.30). The INTRTIE bit is compatible with previous TI CardBus controllers, and when set to
1, ties INTB to INTA internally. The TIEALL bit ties INTA, INTB, and INTC together internally. The internal interrupt
connections set by INTRTIE and TIEALL are communicated to host software through this standard register interface.
This read-only register is described for all PCI7410 functions in Table 4–6.
PCI function 0
Bit
7
6
5
Type
R
R
R
R
Default
0
0
0
0
7
6
5
4
Name
4
3
2
1
0
R
R
R
R
0
0
0
1
3
2
1
0
Interrupt pin – PCI function 0
PCI function 1
Bit
Name
Interrupt pin – PCI function 1
Type
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
1
0
7
6
5
4
3
2
1
0
PCI function 2
Bit
Name
Interrupt pin – PCI function 2
Type
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
1
1
Register:
Offset:
Type:
Default:
Interrupt pin
3Dh
Read-only
01h (function 0), 02h (function 1), 03h (function 2)
Table 4–6. Interrupt Pin Register Cross Reference
4–14
INTRTIE BIT
(BIT 29, OFFSET 80h)
TIEALL BIT
(BIT 28, OFFSET 80h)
INTPIN
FUNCTION 0
(CARDBUS)
INTPIN
FUNCTION 1
(DEDICATED SOCKET)
INTPIN
FUNCTION 2
(1394 OHCI)
0
0
01h (INTA)
02h (INTB)
03h (INTC)
1
0
01h (INTA)
01h (INTA)
03h (INTC)
X
1
01h (INTA)
01h (INTA)
01h (INTA)
4.26 Bridge Control Register
The bridge control register provides control over various PCI7410 bridging functions. Some bits in this register are
global in nature and must be accessed only through function 0. See Table 4–7 for a complete description of the
register contents.
Bit
15
14
13
12
11
10
9
Name
8
7
6
5
4
3
2
1
0
Bridge control
Type
R
R
R
R
R
RW
RW
RW
RW
RW
RW
R
RW
RW
RW
RW
Default
0
0
0
0
0
0
1
1
0
1
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Bridge control
3Eh (Function 0, 1)
Read-only, Read/Write
0340h
Table 4–7. Bridge Control Register Description
BIT
SIGNAL
TYPE
15–11
RSVD
R
10
9
POSTEN
PREFETCH1
FUNCTION
These bits return 0s when read.
RW
Write posting enable. Enables write posting to and from the CardBus sockets. Write posting enables the
posting of write data on burst cycles. Operating with write posting disabled impairs performance on burst
cycles. Note that burst write data can be posted, but various write transactions may not. This bit is socket
dependent and is not shared between functions 0 and 1.
RW
Memory window 1 type. This bit specifies whether or not memory window 1 is prefetchable. This bit is
socket dependent. This bit is encoded as:
0 = Memory window 1 is nonprefetchable.
1 = Memory window 1 is prefetchable (default).
8
PREFETCH0
RW
Memory window 0 type. This bit specifies whether or not memory window 0 is prefetchable. This bit is
socket dependent. This bit is encoded as:
0 = Memory window 0 is nonprefetchable.
1 = Memory window 0 is prefetchable (default).
7
INTR
RW
PCI interrupt – IREQ routing enable. This bit is used to select whether PC Card functional interrupts are
routed to PCI interrupts or to the IRQ specified in the ExCA registers.
0 = Functional interrupts are routed to PCI interrupts (default).
1 = Functional interrupts are routed by ExCA registers.
6†
CRST
RW
CardBus reset. When this bit is set, the CRST signal is asserted on the CardBus interface. The CRST
signal can also be asserted by passing a PRST assertion to CardBus.
0 = CRST is deasserted.
1 = CRST is asserted (default).
This bit is not cleared by the assertion of PRST. It is only cleared by the assertion of GRST.
Master abort mode. This bit controls how the PCI7410 device responds to a master abort when the
PCI7410 device is an initiator on the CardBus interface. This bit is common between each socket.
0 = Master aborts not reported (default).
1 = Signal target abort on PCI and signal SERR, if enabled.
5
MABTMODE
RW
4
RSVD
R
3
VGAEN
RW
VGA enable. This bit affects how the PCI7410 device responds to VGA addresses. When this bit is set,
accesses to VGA addresses will be forwarded.
2
ISAEN
RW
ISA mode enable. This bit affects how the PCI7410 device passes I/O cycles within the 64-Kbyte ISA
range. This bit is not common between sockets. When this bit is set, the PCI7410 device does not forward
the last 768 bytes of each 1K I/O range to CardBus.
RW
CSERR enable. This bit controls the response of the PCI7410 device to CSERR signals on the CardBus
bus. This bit is separate for each socket.
0 = CSERR is not forwarded to PCI SERR (default)
1 = CSERR is forwarded to PCI SERR.
1
CSERREN
This bit returns 0 when read.
† One or more bits in this register are PME context bits and can be cleared only by the assertion of GRST when PME is enabled. If PME is not
enabled, then this bit is cleared by the assertion of PRST or GRST.
4–15
Table 4–7. Bridge Control Register Description (Continued)
BIT
SIGNAL
TYPE
FUNCTION
0
CPERREN
RW
CardBus parity error response enable. This bit controls the response of the PCI7410 to CardBus parity
errors. This bit is separate for each socket.
0 = CardBus parity errors are ignored (default).
1 = CardBus parity errors are reported using CPERR.
4.27 Subsystem Vendor ID Register
The subsystem vendor ID register, used for system and option card identification purposes, may be required for
certain operating systems. This register is read-only or read/write, depending on the setting of bit 5 (SUBSYSRW)
in the system control register (PCI offset 80h, See Section 4.30). When bit 5 is 0, this register is read/write; when bit
5 is 1, this register is read-only. The default mode is read-only. All bits in this register are reset by GRST only.
Bit
15
14
13
12
11
10
9
Name
8
7
6
5
4
3
2
1
0
Subsystem vendor ID
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Subsystem vendor ID
40h (Functions 0, 1)
Read-only, (Read/Write when bit 5 in the system control register is 0)
0000h
4.28 Subsystem ID Register
The subsystem ID register, used for system and option card identification purposes, may be required for certain
operating systems. This register is read-only or read/write, depending on the setting of bit 5 (SUBSYSRW) in the
system control register (PCI offset 80h, see Section 4.30). When bit 5 is 0, this register is read/write; when bit 5 is
1, this register is read-only. The default mode is read-only. All bits in this register are reset by GRST only.
If an EEPROM is present, then the subsystem ID and subsystem vendor ID is loaded from the EEPROM after a reset.
Bit
15
14
13
12
11
10
9
Type
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
Name
7
6
5
4
3
2
1
0
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
Subsystem ID
Register:
Offset:
Type:
Default:
4–16
8
Subsystem ID
42h (Functions 0, 1)
Read-only, (Read/Write when bit 5 in the system control register is 0)
0000h
4.29 PC Card 16-Bit I/F Legacy-Mode Base-Address Register
The PCI7410 device supports the index/data scheme of accessing the ExCA registers, which is mapped by this
register. An address written to this register is the address for the index register and the address+1 is the data address.
Using this access method, applications requiring index/data ExCA access can be supported. The base address can
be mapped anywhere in 32-bit I/O space on a word boundary; hence, bit 0 is read-only, returning 1 when read. As
specified in the PCI to PCMCIA CardBus Bridge Register Description specification, this register is shared by functions
0 and 1. See the ExCA register set description in Section 5 for register offsets. All bits in this register are reset by
GRST only.
Bit
31
30
29
28
27
Name
Type
26
25
24
23
22
21
20
19
18
17
16
PC Card 16-bit I/F legacy-mode base-address
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
PC Card 16-bit I/F legacy-mode base-address
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
R
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
Register:
Offset:
Type:
Default:
PC Card 16-bit I/F legacy-mode base-address
44h (Functions 0, 1)
Read-only, Read/Write
0000 0001h
4–17
4.30 System Control Register
System-level initializations are performed through programming this doubleword register. Some of the bits are global
in nature and must be accessed only through function 0. See Table 4–8 for a complete description of the register
contents.
Bit
31
30
29
28
27
26
25
Name
Type
24
23
22
21
20
19
18
17
16
System control
RW
RW
RW
RW
R
RW
RW
RW
R
RW
RW
RW
RW
RW
RW
RW
Default
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
System control
RW
RW
R
R
R
R
R
R
R
RW
RW
RW
RW
R
RW
RW
1
0
0
1
0
0
0
0
0
1
1
0
0
0
0
0
Register:
Offset:
Type:
Default:
System control
80h (Functions 0, 1)
Read-only, Read/Write
0800 9060h
Table 4–8. System Control Register Description
BIT
SIGNAL
TYPE
FUNCTION
31–30 ‡§
SER_STEP
RW
Serial input stepping. In serial PCI interrupt mode, these bits are used to configure the serial stream PCI
interrupt frames, and can be used to accomplish an even distribution of interrupts signaled on the four PCI
interrupt slots.
00 = INTA/INTB/INTC signal in INTA/INTB/INTC slots (default)
01 = INTA/INTB/INTC signal in INTB/INTC/INTD slots
10 = INTA/INTB/INTC signal in INTC/INTD/INTA slots
11 = INTA/INTB/INTC signal in INTD/INTA/INTB slots
29 ‡§
INTRTIE
RW
This bit ties INTA to INTB internally (to INTA), and reports this through the interrupt pin register (PCI offset
3Dh, see Section 4.25). This bit has no effect on INTC.
28 ‡
TIEALL
RW
This bit ties INTA, INTB, and INTC internally (to INTA), and reports this through the interrupt pin register
(PCI offset 3Dh, see Section 4.25).
27 ‡
RSVD
RW
Internal oscillator is always enabled.
26 ‡§
SMIROUTE
RW
SMI interrupt routing. This bit is shared between functions 0 and 1, and selects whether IRQ2 or CSC is
signaled when a write occurs to power a PC Card socket.
0 = PC Card power change interrupts are routed to IRQ2 (default).
1 = A CSC interrupt is generated on PC Card power changes.
RW
SMI interrupt status. This socket-dependent bit is set when a write occurs to set the socket power, and
the SMIENB bit is set. Writing a 1 to this bit clears the status.
0 = SMI interrupt is signaled.
1 = SMI interrupt is not signaled.
SMI interrupt mode enable. When this bit is set, the SMI interrupt signaling generates an interrupt when
a write to the socket power control occurs. This bit is shared and defaults to 0 (disabled).
0 = SMI interrupt mode is disabled (default).
1 = SMI interrupt mode is enabled.
25 ‡
SMISTATUS
24 ‡§
SMIENB
RW
23
RSVD
R
22 ‡
CBRSVD
RW
Reserved
CardBus reserved terminals signaling. When this bit is set, the RSVD CardBus terminals are driven low
when a CardBus card has been inserted. When this bit is low, these signals are placed in a high-impedance
state.
0 = Place the CardBus RSVD terminals in a high-impedance state.
1 = Drive the CardBus RSVD terminals low (default).
‡ One or more bits in this register are cleared only by the assertion of GRST.
§ These bits are global in nature and must be accessed only through function 0.
4–18
Table 4–8. System Control Register Description (continued)
BIT
SIGNAL
TYPE
21 ‡
VCCPROT
RW
VCC protection enable. This bit is socket dependent.
0 = VCC protection is enabled for 16-bit cards (default).
1 = VCC protection is disabled for 16-bit cards.
Reduced zoomed video enable. When this bit is enabled, AD25–AD22 of the card interface for 16-bit
PC Cards are placed in the high impedance state. This bit is encoded as:
0 = Reduced zoomed video is disabled (default).
1 = Reduced zoomed video is enabled.
20 ‡
REDUCEZV
RW
19–16 ‡
RSVD
R
15 ‡§
14 ‡§
MRBURSTDN
MRBURSTUP
FUNCTION
Reserved. These bits return 0s when read.
RW
Memory read burst enable downstream. When this bit is set, the PCI7410 device allows memory read
transactions to burst downstream.
0 = MRBURSTDN downstream is disabled.
1 = MRBURSTDN downstream is enabled (default).
RW
Memory read burst enable upstream. When this bit is set, the PCI7410 device allows memory read
transactions to burst upstream.
0 = MRBURSTUP upstream is disabled (default).
1 = MRBURSTUP upstream is enabled.
13 ‡
SOCACTIVE
R
Socket activity status. When set, this bit indicates access has been performed to or from a PC Card.
Reading this bit causes it to be cleared. This bit is socket dependent.
0 = No socket activity (default)
1 = Socket activity
12
RSVD
R
Reserved. This bit returns 1 when read.
R
Power-stream-in-progress status bit. When set, this bit indicates that a power stream to the power
switch is in progress and a powering change has been requested. When this bit is cleared, it indicates
that the power stream is complete.
0 = Power stream is complete, delay has expired (default).
1 = Power stream is in progress.
R
Power-up delay-in-progress status bit. When set, this bit indicates that a power-up stream has been
sent to the power switch, and proper power may not yet be stable. This bit is cleared when the power-up
delay has expired.
0 = Power-up delay has expired (default).
1 = Power-up stream sent to switch. Power might not be stable.
11 ‡
10 †
PWRSTREAM
DELAYUP
9†
DELAYDOWN
R
Power-down delay-in-progress status bit. When set, this bit indicates that a power-down stream has
been sent to the power switch, and proper power may not yet be stable. This bit is cleared when the
power-down delay has expired.
0 = Power-down delay has expired (default).
1 = Power-down stream sent to switch. Power might not be stable.
8†
INTERROGATE
R
Interrogation in progress. When set, this bit indicates an interrogation is in progress, and clears when
the interrogation completes. This bit is socket-dependent.
0 = Interrogation not in progress (default)
1 = Interrogation in progress
7
RSVD
R
Reserved. This bit returns 0 when read.
† One or more bits in this register are PME context bits and can be cleared only by the assertion of GRST when PME is enabled. If PME is not
enabled, then this bit is cleared by the assertion of PRST or GRST.
‡ One or more bits in this register are cleared only by the assertion of GRST.
§ These bits are global in nature and must be accessed only through function 0.
4–19
Table 4–8. System Control Register Description (continued)
BIT
6 ‡§
SIGNAL
PWRSAVINGS
TYPE
FUNCTION
RW
Power savings mode enable. When this bit is set, the PCI7410 device consumes less power with no
performance loss. This bit is shared between the two PCI7410 CardBus functions.
0 = Power savings mode disabled
1 = Power savings mode enabled (default)
5 ‡§
SUBSYSRW
RW
Subsystem ID and subsystem vendor ID, ExCA ID and revision register read/write enable. This bit also
controls read/write for the function 3 subsystem ID register.
0 = Registers are read/write.
1 = Registers are read-only (default).
4 ‡§
CB_DPAR
RW
CardBus data parity SERR signaling enable.
0 = CardBus data parity not signaled on PCI SERR signal (default)
1 = CardBus data parity signaled on PCI SERR signal
PC/PCI DMA enable. Enables PC/PCI DMA when set. When PC/PCI DMA is enabled, PCREQ and
PCGNT must be routed to a multifunction routing terminal. See Multifunction Routing Status Register
(PCI offset 8Ch, see Section 4.37) for options.
0 = Centralized DMA disabled (default)
1 = Centralized DMA enabled
3 ‡§
CDMA_EN
RW
2‡
EXCAPOWER
R
1 ‡§
KEEPCLK
RW
ExCA power control bit.
0 = Enables 3.3 V (defoult)
1 = Enables 5 V
Keep clock. When this bit is set, the PCI7410 device follows the CLKRUN protocol to maintain the
system PCLK and the CCLK (CardBus clock). This bit is global to the PCI7410 functions.
0 = Allow system PCLK and CCLK to stop (default)
1 = Never allow system PCLK or CCLK clock to stop
Note that the functionality of this bit has changed relative to that of the PCI12XX family of TI CardBus
controllers. In these CardBus controllers, setting this bit only maintains the PCI clock, not the CCLK.
In the PCI7410 device, setting this bit maintains both the PCI clock and the CCLK.
0 ‡§
RIMUX
RW
PME/RI_OUT select bit. When this bit is 1, the PME signal is routed to the PME/RI_OUT terminal (PDV
21, GHK J03). When this bit is 0 and bit 7 (RIENB) of the card control register is 1, the RI_OUT signal
is routed to the PME/RI_OUT terminal (PDV 21, GHK J03). If this bit is 0 and bit 7 (RIENB) of the card
control register is 0, then the output (PDV 21, GHK J03) is placed in a high-impedance state. This
terminal is encoded as:
0 = RI_OUT signal is routed to the PME/RI_OUT terminal (PDV 21, GHK J03) if bit 7 of the card
control register is 1. (default)
1 = PME signal is routed to the PME/RI_OUT terminal (PDV 21, GHK J03) of the PCI7410
controller.
NOTE: If this bit (bit 0) is 0 and bit 7 of the card control register (PCI offset 91h, see Section 4.39) is
0, then the output on the PME/RI_OUT terminal (PDV 21, GHK J03) is placed in a high-impedance
state.
‡ One or more bits in this register are cleared only by the assertion of GRST.
§ These bits are global in nature and must be accessed only through function 0.
4.31 UM_CD Debounce Register
This register provides debounce time in units of 2 ms for the UM_CD signal on UltraMedia cards. This register defaults
to19h, which gives a default debounce time of 50 ms. All bits in this register are reset by GRST only.
Bit
7
6
5
4
RW
RW
RW
RW
0
0
0
1
Name
Type
Default
2
1
0
RW
RW
RW
RW
1
0
0
1
UM_CD debounce
Register:
Offset:
Type:
Default:
4–20
3
UM_CD debounce
84h (Functions 0, 1)
Read/Write
19h
4.32 General Control Register
The general control register provides top level PCI arbitration control. See Table 4–9 for a complete description of
the register contents.
Bit
15
14
13
12
11
10
9
Name
8
7
6
5
4
3
2
1
0
General control
Type
R
R
R
R
R
R
RW
RW
R
R
RW
RW
RW
R
RW
RW
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
General control
86h
Read/Write, Read-only
0000h
Table 4–9. General Control Register Description
BIT
SIGNAL
TYPE
15–13 ‡
RSVD
RW
These bits are for test purposes and must not be changed from their default values of 000b.
12 ‡
IO_LIMIT_SEL
RW
When this bit is set, bit 0 in the I/O limit registers (PCI offsets 30h and 38h) for both CardBus functions
is set.
0 = Bit 0 in the I/O limit registers is 0 (default)
1 = Bit 0 in the I/O limit registers is 1
11 ‡
IO_BASE_SEL
RW
When this bit is set, bit 0 in the I/O base registers (PCI offsets 2Ch and 34h) for both CardBus functions
is set.
0 = Bit 0 in the I/O base registers is 0 (default)
1 = Bit 0 in the I/O base registers is 1
10 ‡
12V_SW_SEL
RW
Power switch select. This bit selects which power switch is implemented in the system.
0 = A 1.8-V capable power switch (TPS2221) is used (default)
1 = A 12-V capable power switch (TPS2211) is used
9–8
RSVD
R
7‡
PCI2_3_EN
RW
6
RSVD
R
5‡
DISABLE_FWL
RW
When this bit is set, the firmware loader function is completely nonaccessible and nonfunctional.
4‡
DISABLE_DED_
SKT
RW
When this bit is set, the dedicated socket function is completely nonaccessible and nonfunctional.
3‡
DISABLE_OHCI
RW
When set, the OHCI 1394 controller function is completely nonaccessible and nonfunctional.
2
RSVD
R
1–0 ‡
ARB_CTRL
RW
FUNCTION
Reserved. These bits return 0 when read.
PCI 2.3 enable. When this bit is set, the PCI7410 CardBus functions conform to the PCI 2.3
specification. When in the PCI 2.3 mode, the INT_DISABLE and INT_STATUS bits per the PCI 2.3
specification are functional. When this bit is cleared, the function conforms to the PCI 2.2 specification
and all PCI 2.3 bits are disabled.
0 = PCI 2.2 mode (default)
1 = PCI 2.3 mode
Reserved. This bit returns 0 when read.
Reserved. This bit returns 0 when read.
Controls top level PCI arbitration:
00 = 1394 OHCI priority
01 = CardBus priority
10 = Fair round robin
11 = Fair round robin
‡ One or more bits in this register are cleared only by the assertion of GRST.
4–21
4.33 General-Purpose Event Status Register
The general-purpose event status register contains status bits that are set when general events occur, and can be
programmed to generate general-purpose event signaling through GPE. See Table 4–10 for a complete description
of the register contents.
Bit
7
6
5
Name
Type
Default
4
3
2
1
0
General-purpose event status
RCU
RCU
R
RCU
RCU
RCU
RCU
RCU
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
General-purpose event status
88h
Read/Clear/Update, Read-only
00h
Table 4–10. General-Purpose Event Status Register Description
BIT
SIGNAL
TYPE
FUNCTION
7‡
PWR_STS
RCU
Power change status. This bit is set when software changes the VCC or VPP power state of either socket.
6‡
VPP12_STS
RCU
12-V VPP request status. This bit is set when software has changed the requested VPP level to or from 12 V
for either socket.
5
RSVD
R
4‡
GP4_STS
RCU
GPI4 status. This bit is set on a change in status of the MFUNC5 terminal input level if configured as a
general-purpose input, GPI4.
3‡
GP3_STS
RCU
GPI3 status. This bit is set on a change in status of the MFUNC4 terminal input level if configured as a
general-purpose input, GPI3.
2‡
GP2_STS
RCU
GPI2 status. This bit is set on a change in status of the MFUNC2 terminal input level if configured as a
general-purpose input, GPI2.
1‡
GP1_STS
RCU
GPI1 status. This bit is set on a change in status of the MFUNC1 terminal input level if configured as a
general-purpose input, GPI1.
0‡
GP0_STS
RCU
GPI0 status. This bit is set on a change in status of the MFUNC0 terminal input level if configured as a
general-purpose input, GPI0.
Reserved. This bit returns 0 when read. A write has no effect.
‡ One or more bits in this register are cleared only by the assertion of GRST.
4–22
4.34 General-Purpose Event Enable Register
The general-purpose event enable register contains bits that are set to enable GPE signals. See Table 4–11 for a
complete description of the register contents.
Bit
7
6
5
Name
Type
Default
4
3
2
1
0
General-purpose event enable
RW
RW
R
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
General-purpose event enable
89h
Read-only, Read/Write
00h
Table 4–11. General-Purpose Event Enable Register Description
BIT
SIGNAL
TYPE
7‡
PWR_EN
RW
Power change GPE enable. When this bit is set, GPE is signaled on PWR_STS events.
FUNCTION
6‡
VPP12_EN
RW
12-V VPP GPE enable. When this bit is set, GPE is signaled on VPP12_STS events.
5
RSVD
R
4‡
GP4_EN
RW
GPI4 GPE enable. When this bit is set, GPE is signaled on GP4_STS events.
3‡
GP3_EN
RW
GPI3 GPE enable. When this bit is set, GPE is signaled on GP3_STS events.
2‡
GP2_EN
RW
GPI2 GPE enable. When this bit is set, GPE is signaled on GP2_STS events.
1‡
GP1_EN
RW
GPI1 GPE enable. When this bit is set, GPE is signaled on GP1_STS events.
0‡
GP0_EN
RW
GPI0 GPE enable. When this bit is set, GPE is signaled on GP0_STS events.
Reserved. This bit returns 0 when read. A write has no effect.
‡ One or more bits in this register are cleared only by the assertion of GRST.
4.35 General-Purpose Input Register
The general-purpose input register contains the logical value of the data input to the GPI terminals. See Table 4–12
for a complete description of the register contents.
Bit
7
6
5
Type
R
R
R
RU
Default
0
0
0
X
Name
4
3
2
1
0
RU
RU
RU
RU
X
X
X
X
General-purpose input
Register:
Offset:
Type:
Default:
General-purpose input
8Ah
Read/Update, Read-only
XXh
Table 4–12. General-Purpose Input Register Description
BIT
SIGNAL
TYPE
7–5
RSVD
R
FUNCTION
4
GPI4_DATA
RU
GPI4 data input. This bit represents the logical value of the data input from GPI4.
3
GPI3_DATA
RU
GPI3 data input. This bit represents the logical value of the data input from GPI3.
2
GPI2_DATA
RU
GPI2 data input. This bit represents the logical value of the data input from GPI2.
1
GPI1_DATA
RU
GPI1 data input. This bit represents the logical value of the data input from GPI1.
0
GPI0_DATA
RU
GPI0 data input. This bit represents the logical value of the data input from GPI0.
Reserved. These bits return 0s when read. Writes have no effect.
4–23
4.36 General-Purpose Output Register
The general-purpose output register is used to drive the GPO4–GPO0 outputs. See Table 4–13 for a complete
description of the register contents.
Bit
7
6
5
Name
4
3
2
1
0
General-purpose output
Type
R
R
R
RW
RW
RW
RW
RW
Default
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
General-purpose output
8Bh
Read-only, Read/Write
00h
Table 4–13. General-Purpose Output Register Description
BIT
SIGNAL
TYPE
7–5
RSVD
R
FUNCTION
4‡
GPO4_DATA
RW
This bit represents the logical value of the data driven to GPO4.
3‡
GPO3_DATA
RW
This bit represents the logical value of the data driven to GPO3.
2‡
GPO2_DATA
RW
This bit represents the logical value of the data driven to GPO2.
1‡
GPO1_DATA
RW
This bit represents the logical value of the data driven to GPO1.
0‡
GPO0_DATA
RW
This bit represents the logical value of the data driven to GPO0.
Reserved. These bits return 0s when read. Writes have no effect.
‡ One or more bits in this register are cleared only by the assertion of GRST.
4–24
4.37 Multifunction Routing Status Register
The multifunction routing status register is used to configure the MFUNC6–MFUNC0 terminals. These terminals may
be configured for various functions. This register is intended to be programmed once at power-on initialization. The
default value for this register can also be loaded through a serial EEPROM. See Table 4–14 for a complete description
of the register contents.
Bit
31
30
29
28
27
26
Name
25
24
23
22
21
20
19
18
17
16
Multifunction routing status
Type
R
RW
RW
RW
R
RW
RW
RW
R
RW
RW
RW
R
RW
RW
RW
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Multifunction routing status
Type
R
RW
RW
RW
R
RW
RW
RW
R
RW
RW
RW
R
RW
RW
RW
Default
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Multifunction routing status
8Ch
Read/Write, Read-only
0000 1000h
Table 4–14. Multifunction Routing Status Register Description
BIT
SIGNAL
TYPE
31–28 ‡
RSVD
R
27–24 ‡
23–20 ‡
MFUNC6
MFUNC5
FUNCTION
Bits 31–28 return 0s when read.
RW
Multifunction terminal 6 configuration. These bits control the internal signal mapped to the MFUNC6 terminal
as follows:
0000 = RSVD
0100 = IRQ4
1000 = IRQ8
1100 = IRQ12
0001 = CLKRUN
0101 = IRQ5
1001 = IRQ9
1101 = IRQ13
0010 = IRQ2
0110 = IRQ6
1010 = IRQ10
1110 = IRQ14
0011 = IRQ3
0111 = IRQ7
1011 = IRQ11
1111 = IRQ15
RW
Multifunction terminal 5 configuration. These bits control the internal signal mapped to the MFUNC5 terminal
as follows:
0000 = GPI4
0100 = IRQ4
1000 = CAUDPWM
1100 = LEDA1
0001 = GPO4
0101 = IRQ5
1001 = IRQ9
1101 = LED_SKT
0010 = PCGNT
0110 = ZVSTAT
1010 = IRQ10
1110 = GPE
0011 = IRQ3
0111 = RSVD
1011 = OHCI_LED
1111 = IRQ15
Multifunction terminal 4 configuration. These bits control the internal signal mapped to the MFUNC4 terminal
as follows:
19–16 ‡
15–12 ‡
11–8 ‡
MFUNC4
MFUNC3
MFUNC2
RW
0000 = GPI3
0001 = GPO3
0010 = LOCK PCI
0011 = IRQ3
0100 = IRQ4
0101 = IRQ5
0110 = ZVSTAT
0111 = RSVD
1000 = CAUDPWM
1001 = IRQ9
1010 = RSVD
1011 = IRQ11
1100 = RI_OUT
1101 = LED_SKT
1110 = GPE
1111 = IRQ15
RW
Multifunction terminal 3 configuration. These bits control the internal signal mapped to the MFUNC3 terminal
as follows:
0000 = RSVD
0100 = IRQ4
1000 = IRQ8
1100 = IRQ12
0001 = IRQSER
0101 = IRQ5
1001 = IRQ9
1101 = IRQ13
0010 = IRQ2
0110 = IRQ6
1010 = IRQ10
1110 = IRQ14
0011 = IRQ3
0111 = IRQ7
1011 = IRQ11
1111 = IRQ15
RW
Multifunction terminal 2 configuration. These bits control the internal signal mapped to the MFUNC2 terminal
as follows:
0000 = GPI2
0100 = IRQ4
1000 = CAUDPWM
1100 = RI_OUT
0001 = GPO2
0101 = IRQ5
1001 = IRQ9
1101 = TEST_MUX
0010 = PCREQ
0110 = ZVSTAT
1010 = IRQ10
1110 = GPE
0011 = IRQ3
0111 = ZVSEL0
1011 = INTC
1111 = IRQ7
‡ One or more bits in this register are cleared only by the assertion of GRST.
4–25
Table 4–14. Multifunction Routing Status Register Description (Continued)
BIT
7–4 ‡
3–0 ‡
SIGNAL
MFUNC1
MFUNC0
TYPE
FUNCTION
RW
Multifunction terminal 1 configuration. These bits control the internal signal mapped to the MFUNC1 terminal
as follows:
0000 = GPI1
0100 = OHCI_LED 1000 = CAUDPWM
1100 = LEDA1
0001 = GPO1
0101 = IRQ5
1001 = IRQ9
1101 = LEDA2
0110 = ZVSTAT
1010 = IRQ10
1110 = GPE
0010 = INTB
0011 = IRQ3
0111 = ZVSEL0
1011 = IRQ11
1111 = IRQ15
RW
Multifunction terminal 0 configuration. These bits control the internal signal mapped to the MFUNC0 terminal
as follows:
0000 = GPI0
0100 = IRQ4
1000 = CAUDPWM
1100 = LEDA1
0001 = GPO0
0101 = IRQ5
1001 = IRQ9
1101 = LEDA2
0110 = ZVSTAT
1010 = IRQ10
1110 = GPE
0010 = INTA
0011 = IRQ3
0111 = ZVSEL0
1011 = IRQ11
1111 = IRQ15
‡ One or more bits in this register are cleared only by the assertion of GRST.
4.38 Retry Status Register
The contents of the retry status register enable the retry time-out counters and display the retry expiration status. The
flags are set when the PCI7410 device, as a master, receives a retry and does not retry the request within 215 clock
cycles. The flags are cleared by writing a 1 to the bit. Access this register only through function 0. See Table 4–15
for a complete description of the register contents.
Bit
7
6
5
4
Name
Type
Default
3
2
1
0
Retry status
RW
RW
RC
R
RC
R
RC
R
1
1
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Retry status
90h (Functions 0, 1)
Read-only, Read/Write, Read/Clear
C0h
Table 4–15. Retry Status Register Description
BIT
SIGNAL
TYPE
FUNCTION
7‡
PCIRETRY
RW
PCI retry time-out counter enable. This bit is encoded as:
0 = PCI retry counter disabled
1 = PCI retry counter enabled (default)
6 ‡§
CBRETRY
RW
CardBus retry time-out counter enable. This bit is encoded as:
0 = CardBus retry counter disabled
1 = CardBus retry counter enabled (default)
5‡
TEXP_CBB
RC
CardBus target B retry expired. Write a 1 to clear this bit.
0 = Inactive (default)
1 = Retry has expired.
4
RSVD
R
3 ‡§
TEXP_CBA
RC
2
RSVD
R
1‡
TEXP_PCI
RC
0
RSVD
R
Reserved. This bit returns 0 when read.
CardBus target A retry expired. Write a 1 to clear this bit.
0 = Inactive (default)
1 = Retry has expired.
Reserved. This bit returns 0 when read.
PCI target retry expired. Write a 1 to clear this bit.
0 = Inactive (default)
1 = Retry has expired.
Reserved. This bit returns 0 when read.
‡ One or more bits in this register are cleared only by the assertion of GRST.
§ These bits are global in nature and must be accessed only through function 0.
4–26
4.39 Card Control Register
The card control register is provided for PCI1130 compatibility. RI_OUT is enabled through this register, and the
enable bit is shared between functions 0 and 1. See Table 4–16 for a complete description of the register contents.
The RI_OUT signal is enabled through this register, and the enable bit is shared between functions 0 and 1.
Bit
7
6
5
4
3
2
1
0
RW
RW
RW
R
0
0
0
R
RW
RW
RW
0
0
0
0
0
Name
Type
Default
Card control
Register:
Offset:
Type:
Default:
Card control
91h
Read-only, Read/Write
00h
Table 4–16. Card Control Register Description
BIT
SIGNAL
TYPE
7 ‡§
RIENB
RW
Ring indicate enable. When this bit is 1, the RI_OUT output is enabled. This bit defaults to 0.
6‡
ZVENABLE
RW
Compatibility ZV mode enable. When this bit is 1, the corresponding PC Card socket interface ZV
terminals enter a high-impedance state. This bit defaults to 0.
5‡
PORT_SEL
RW
4–3
RSVD
R
2‡
1‡
AUD2MUX
SPKROUTEN
RW
RW
FUNCTION
Port select. This bit controls the priority for the ZV_SEL0 and ZV_SEL1 signaling if bit 6 (ZVENABLE) is
set in both functions.
0 = Socket 0 takes priority, as signaled through ZV_SEL0, when both sockets are in ZV mode.
1 = Socket 1 takes priority, as signaled through ZV_SEL1, when both sockets are in ZV mode.
Reserved. These bits default to 0.
CardBus audio-to-MFUNC. When this bit is set, the CAUDIO CardBus signal must be routed through an
MFUNC terminal. If this bit is set for both functions, then function 0 is routed.
0 = CAUDIO set to CAUDPWM on MFUNC terminal (default)
1 = CAUDIO is not routed.
When bit 1 is set, the SPKR termijnal from the PC Card is enabled and is routed to tthe SPKROUT terminal.
The SPKR signal from socket 0 is XORed with the SPKR signal from socket 1 and sent to SPKROUT. The
SPKROUT terminal drives data only when the SPKROUTEN bit of either function is set. This bit is encoded
as:
0 = SPKR to SPKROUT not enabled (default)
1 = SPKR to SPKROUT enabled
0‡
IFG
RW
Interrupt flag. This bit is the interrupt flag for 16-bit I/O PC Cards and for CardBus cards. This bit is set when
a functional interrupt is signaled from a PC Card interface, and is socket dependent (i.e., not global). Write
back a 1 to clear this bit.
0 = No PC Card functional interrupt detected (default)
1 = PC Card functional interrupt detected
‡ One or more bits in this register are cleared only by the assertion of GRST.
§ This bit is global in nature and must be accessed only through function 0.
4–27
4.40 Device Control Register
The device control register is provided for PCI1130 compatibility. It contains bits that are shared between functions
0 and 1. The interrupt mode select is programmed through this register. The socket-capable force bits are also
programmed through this register. See Table 4–17 for a complete description of the register contents.
Bit
7
6
5
4
Name
Type
Default
3
2
1
0
Device control
RW
RW
RW
R
RW
RW
RW
RW
0
1
1
0
0
1
1
0
Register:
Offset:
Type:
Default:
Device control
92h (Functions 0, 1)
Read-only, Read/Write
66h
Table 4–17. Device Control Register Description
BIT
SIGNAL
TYPE
FUNCTION
7‡
SKTPWR_LOCK
RW
Socket power lock bit. When this bit is set to 1, software cannot power down the PC Card socket while
in D3. It may be necessary to lock socket power in order to support wake on LAN or RING if the
operating system is programmed to power down a socket when the CardBus controller is placed in the
D3 state.
6 ‡§
3VCAPABLE
RW
3-V socket capable force bit.
0 = Not 3-V capable
1 = 3-V capable (default)
5‡
IO16R2
RW
Diagnostic bit. This bit defaults to 1.
4
RSVD
R
3 ‡§
TEST
RW
TI test bit. Write only 0 to this bit.
Reserved. This bit returns 0 when read. A write has no effect.
2–1 ‡§
INTMODE
RW
Interrupt mode. These bits select the interrupt signaling mode. The interrupt mode bits are encoded:
00 = Parallel PCI interrupts only
01 = Reserved
10 = IRQ serialized interrupts and parallel PCI interrupts INTA and INTB
11 = IRQ and PCI serialized interrupts (default)
0 ‡§
RSVD
RW
Reserved. Bit 0 is reserved for test purposes. Only a 0 must be written to this bit.
‡ One or more bits in this register are cleared only by the assertion of GRST.
§ These bits are global in nature and must be accessed only through function 0.
4–28
4.41 Diagnostic Register
The diagnostic register is provided for internal TI test purposes. It is a read/write register, but only 0s must be written
to it. See Table 4–18 for a complete description of the register contents.
Bit
7
6
5
4
3
2
1
0
RW
R
RW
RW
0
1
1
RW
RW
RW
RW
0
0
0
0
0
Name
Type
Default
Diagnostic
Register:
Offset:
Type:
Default:
Diagnostic
93h (functions 0, 1)
Read/Write
60h
Table 4–18. Diagnostic Register Description
BIT
SIGNAL
TYPE
FUNCTION
This bit defaults to 0. This bit is encoded as:
0 = Reads true values in PCI vendor ID and PCI device ID registers (default)
1 = Returns all 1s to reads from the PCI vendor ID and PCI device ID registers
7 ‡§
TRUE_VAL
RW
6‡
RSVD
R
5‡
CSC
RW
CSC interrupt routing control
0 = CSC interrupts routed to PCI if ExCA 803 bit 4 = 1
1 = CSC interrupts routed to PCI if ExCA 805 bits 7–4 = 0000b (default).
In this case, the setting of ExCA 803 bit 4 is a don’t care.
4 ‡§
DIAG4
RW
Diagnostic RETRY_DIS. Delayed transaction disable.
3 ‡§
DIAG3
RW
2 ‡§
DIAG2
RW
Diagnostic RETRY_EXT. Extends the latency from 16 to 64.
Diagnostic DISCARD_TIM_SEL_CB. Set = 210, reset = 215.
1 ‡§
DIAG1
RW
Diagnostic DISCARD_TIM_SEL_PCI. Set = 210, reset = 215.
0‡
ZV_EN
RW
Zoomed video enable.
0 = Enable new ZV register model (default)
1 = Disable new ZV register mode
Reserved. This bit is read-only and returns 1 when read.
‡ One or more bits in this register are cleared only by the assertion of GRST.
§ This bit is global and is accessed only through function 0.
4–29
4.42 Capability ID Register
The capability ID register identifies the linked list item as the register for PCI power management. The register returns
01h when read, which is the unique ID assigned by the PCI SIG for the PCI location of the capabilities pointer and
the value.
Bit
7
6
5
4
Name
3
2
1
0
Capability ID
Type
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
1
Register:
Offset:
Type:
Default:
Capability ID
A0h
Read-only
01h
4.43 Next Item Pointer Register
The contents of this register indicate the next item in the linked list of the PCI power management capabilities.
Because the PCI7410 functions only include one capabilities item, this register returns 0s when read.
Bit
7
6
5
Name
4
3
2
1
0
Next item pointer
Type
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
4–30
Next item pointer
A1h
Read-only
00h
4.44 Power Management Capabilities Register
The power management capabilities register contains information on the capabilities of the PC Card function related
to power management. Both PCI7410 CardBus bridge functions support D0, D1, D2, and D3 power states. Default
register value is FE12h for operation in accordance with PCI Bus Power Management Interface Specification revision
1.1. See Table 4–19 for a complete description of the register contents.
Bit
15
14
13
12
11
10
Name
Type
Default
9
8
7
6
5
4
3
2
1
0
Power management capabilities
RW
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
1
1
1
1
1
1
1
0
0
0
0
1
0
0
1
0
Register:
Offset:
Type:
Default:
Power management capabilities
A2h (Functions 0, 1)
Read-only, Read/Write
FE12h
Table 4–19. Power Management Capabilities Register Description
BIT
SIGNAL
TYPE
FUNCTION
This 5-bit field indicates the power states from which the PCI7410 device functions can assert PME. A 0
for any bit indicates that the function cannot assert the PME signal while in that power state. These 5 bits
return 11111b when read. Each of these bits is described below:
15 ‡
RW
PME support
14–11
Bit 15 – defaults to a 1 indicating the PME signal can be asserted from the D3cold state. This bit is read/write
because wake-up support from D3cold is contingent on the system providing an auxiliary power source
to the VCC terminals. If the system designer chooses not to provide an auxiliary power source to the VCC
terminals for D3cold wake-up support, then BIOS must write a 0 to this bit.
R
Bit 14 – contains the value 1 to indicate that the PME signal can be asserted from the D3hot state.
Bit 13 – contains the value 1 to indicate that the PME signal can be asserted from the D2 state.
Bit 12 – contains the value 1 to indicate that the PME signal can be asserted from the D1 state.
Bit 11 – contains the value 1 to indicate that the PME signal can be asserted from the D0 state.
10
D2_Support
R
This bit returns a 1 when read, indicating that the function supports the D2 device power state.
9
D1_Support
R
This bit returns a 1 when read, indicating that the function supports the D1 device power state.
8–6
RSVD
R
Reserved. These bits return 000b when read.
5
DSI
R
Device-specific initialization. This bit returns 0 when read.
Auxiliary power source. This bit is meaningful only if bit 15 (D3cold supporting PME) is set. When this bit
is set, it indicates that support for PME in D3cold requires auxiliary power supplied by the system by way
of a proprietary delivery vehicle.
4
AUX_PWR
R
A 0 (zero) in this bit field indicates that the function supplies its own auxiliary power source.
If the function does not support PME while in the D3cold state (bit 15=0), then this field must always return
0.
3
PMECLK
R
When this bit is 1, it indicates that the function relies on the presence of the PCI clock for PME operation.
When this bit is 0, it indicates that no PCI clock is required for the function to generate PME.
Functions that do not support PME generation in any state must return 0 for this field.
2–0
Version
R
These 3 bits return 010b when read, indicating that there are 4 bytes of general-purpose power
management (PM) registers as described in draft revision 1.1 of the PCI Bus Power Management Interface
Specification.
‡ One or more bits in this register are cleared only by the assertion of GRST.
4–31
4.45 Power Management Control/Status Register
The power management control/status register determines and changes the current power state of the PCI7410
CardBus function. The contents of this register are not affected by the internally generated reset caused by the
transition from the D3hot to D0 state. See Table 4–20 for a complete description of the register contents.
All PCI registers, ExCA registers, and CardBus registers are reset as a result of a D3hot-to-D0 state transition, with
the exception of the PME context bits (if PME is enabled) and the GRST only bits.
Bit
15
14
13
12
11
10
RWC
R
R
R
R
R
R
RW
R
0
0
0
0
0
0
0
0
0
Name
Type
Default
9
8
7
6
5
4
3
2
1
0
R
R
R
R
R
RW
RW
0
0
0
0
0
0
0
Power management control/status
Register:
Offset:
Type:
Default:
Power management control/status
A4h (Functions 0, 1)
Read-only, Read/Write, Read/Write/Clear
0000h
Table 4–20. Power Management Control/Status Register Description
BIT
SIGNAL
TYPE
FUNCTION
PME status. This bit is set when the CardBus function would normally assert the PME signal, independent
of the state of the PME_EN bit. This bit is cleared by a writeback of 1, and this also clears the PME signal
if PME was asserted by this function. Writing a 0 to this bit has no effect.
15 †
PMESTAT
RC
14–13
DATASCALE
R
This 2-bit field returns 0s when read. The CardBus function does not return any dynamic data.
12–9
DATASEL
R
Data select. This 4-bit field returns 0s when read. The CardBus function does not return any dynamic data.
8‡
PME_ENABLE
RW
This bit enables the function to assert PME. If this bit is cleared, then assertion of PME is disabled. This
bit is not cleared by the assertion of PRST. It is only cleared by the assertion of GRST.
7–2
RSVD
R
Reserved. These bits return 0s when read.
Power state. This 2-bit field is used both to determine the current power state of a function and to set the
function into a new power state. This field is encoded as:
1–0
PWRSTATE
RW
00 = D0
01 = D1
10 = D2
11 = D3hot
† One or more bits in this register are PME context bits and can be cleared only by the assertion of GRST when PME is enabled. If PME is not
enabled, then this bit is cleared by the assertion of PRST or GRST.
‡ One or more bits in this register are cleared only by the assertion of GRST.
4–32
4.46 Power Management Control/Status Bridge Support Extensions Register
This register supports PCI bridge-specific functionality. It is required for all PCI-to-PCI bridges. See Table 4–21 for
a complete description of the register contents.
Bit
7
6
Name
5
4
3
2
1
0
Power management control/status bridge support extensions
Type
R
R
R
R
R
R
R
R
Default
1
1
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Power management control/status bridge support extensions
A6h (Functions 0, 1)
Read-only
C0h
Table 4–21. Power Management Control/Status Bridge Support Extensions Register Description
BIT
SIGNAL
TYPE
FUNCTION
Bus power/clock control enable. This bit returns 1 when read. This bit is encoded as:
0 = Bus power/clock control is disabled.
1 = Bus power/clock control is enabled (default).
7
BPCC_EN
A 0 indicates that the bus power/clock control policies defined in the PCI Bus Power Management Interface
Specification are disabled. When the bus power/clock control enable mechanism is disabled, the power
state field (bits 1–0) of the power management control/status register (PCI offset A4h, see Section 4.45)
cannot be used by the system software to control the power or the clock of the secondary bus. A 1 indicates
that the bus power/clock control mechanism is enabled.
R
6
B2_B3
R
B2/B3 support for D3hot. The state of this bit determines the action that is to occur as a direct result of
programming the function to D3hot. This bit is only meaningful if bit 7 (BPCC_EN) is a 1. This bit is encoded
as:
0 = When the bridge is programmed to D3hot, its secondary bus has its power removed (B3).
1 = When the bridge function is programmed to D3hot, its secondary bus PCI clock is stopped (B2)
(default).
5–0
RSVD
R
Reserved. These bits return 0s when read.
4.47 Power-Management Data Register
The power-management data register returns 0s when read, because the CardBus functions do not report dynamic
data.
Bit
7
6
5
Type
R
R
R
R
Default
0
0
0
0
Name
4
3
2
1
0
R
R
R
R
0
0
0
0
Power-management data
Register:
Offset:
Type:
Default:
Power-management data
A7h (functions 0, 1)
Read-only
00h
4–33
4.48 Serial Bus Data Register
The serial bus data register is for programmable serial bus byte reads and writes. This register represents the data
when generating cycles on the serial bus interface. To write a byte, this register must be programmed with the data,
the serial bus index register must be programmed with the byte address, the serial bus slave address must be
programmed with the 7-bit slave address, and the read/write indicator bit must be reset.
On byte reads, the byte address is programmed into the serial bus index register, the serial bus slave address register
must be programmed with both the 7-bit slave address and the read/write indicator bit, and bit 5 (REQBUSY) in the
serial bus control and status register (see Section 4.51) must be polled until clear. Then the contents of this register
are valid read data from the serial bus interface. See Table 4–22 for a complete description of the register contents.
Bit
7
6
5
4
Name
Type
Default
3
2
1
0
Serial bus data
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Serial bus data
B0h (function 0)
Read/Write
00h
Table 4–22. Serial Bus Data Register Description
BIT
SIGNAL
TYPE
FUNCTION
7–0 ‡
SBDATA
RW
Serial bus data. This bit field represents the data byte in a read or write transaction on the serial interface.
On reads, the REQBUSY bit must be polled to verify that the contents of this register are valid.
‡ One or more bits in this register are cleared only by the assertion of GRST.
4.49 Serial Bus Index Register
The serial bus index register is for programmable serial bus byte reads and writes. This register represents the byte
address when generating cycles on the serial bus interface. To write a byte, the serial bus data register must be
programmed with the data, this register must be programmed with the byte address, and the serial bus slave address
must be programmed with both the 7-bit slave address and the read/write indicator.
On byte reads, the word address is programmed into this register, the serial bus slave address must be programmed
with both the 7-bit slave address and the read/write indicator bit, and bit 5 (REQBUSY) in the serial bus control and
status register (see Section 4.51) must be polled until clear. Then the contents of the serial bus data register are valid
read data from the serial bus interface. See Table 4–23 for a complete description of the register contents.
Bit
7
6
5
Name
Type
Default
4
3
2
1
0
Serial bus index
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Serial bus index
B1h (function 0)
Read/Write
00h
Table 4–23. Serial Bus Index Register Description
BIT
SIGNAL
TYPE
FUNCTION
7–0 ‡
SBINDEX
RW
Serial bus index. This bit field represents the byte address in a read or write transaction on the serial interface.
‡ One or more bits in this register are cleared only by the assertion of GRST.
4–34
4.50 Serial Bus Slave Address Register
The serial bus slave address register is for programmable serial bus byte read and write transactions. To write a byte,
the serial bus data register must be programmed with the data, the serial bus index register must be programmed
with the byte address, and this register must be programmed with both the 7-bit slave address and the read/write
indicator bit.
On byte reads, the byte address is programmed into the serial bus index register, this register must be programmed
with both the 7-bit slave address and the read/write indicator bit, and bit 5 (REQBUSY) in the serial bus control and
status register (see Section 4.51) must be polled until clear. Then the contents of the serial bus data register are valid
read data from the serial bus interface. See Table 4–24 for a complete description of the register contents.
Bit
7
6
5
Name
Type
Default
4
3
2
1
0
Serial bus slave address
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Serial bus slave address
B2h (function 0)
Read/Write
00h
Table 4–24. Serial Bus Slave Address Register Description
BIT
7–1 ‡
0‡
SIGNAL
SLAVADDR
RWCMD
TYPE
FUNCTION
RW
Serial bus slave address. This bit field represents the slave address of a read or write transaction on the
serial interface.
RW
Read/write command. Bit 0 indicates the read/write command bit presented to the serial bus on byte read
and write accesses.
0 = A byte write access is requested to the serial bus interface.
1 = A byte read access is requested to the serial bus interface.
‡ One or more bits in this register are cleared only by the assertion of GRST.
4–35
4.51 Serial Bus Control/Status Register
The serial bus control and status register communicates serial bus status information and selects the quick command
protocol. Bit 5 (REQBUSY) in this register must be polled during serial bus byte reads to indicate when data is valid
in the serial bus data register. See Table 4–25 for a complete description of the register contents.
Bit
7
6
5
RW
R
R
R
0
0
0
0
Name
Type
Default
4
3
2
1
0
RW
RW
RC
RC
0
0
0
0
Serial bus control/status
Register:
Offset:
Type:
Default:
Serial bus control/status
B3h (function 0)
Read-only, Read/Write, Read/Clear
00h
Table 4–25. Serial Bus Control/Status Register Description
BIT
SIGNAL
TYPE
FUNCTION
Protocol select. When bit 7 is set, the send-byte protocol is used on write requests and the receive-byte
protocol is used on read commands. The word address byte in the serial bus index register (see
Section 4.49) is not output by the PCI7410 device when bit 7 is set.
7‡
PROT_SEL
RW
6
RSVD
R
Reserved. Bit 6 returns 0 when read.
5
REQBUSY
R
Requested serial bus access busy. Bit 5 indicates that a requested serial bus access (byte read or write)
is in progress. A request is made, and bit 5 is set, by writing to the serial bus slave address register (see
Section 4.50). Bit 5 must be polled on reads from the serial interface. After the byte read access has been
completed, this bit is cleared and the read data is valid in the serial bus data register.
4
ROMBUSY
R
Serial EEPROM busy status. Bit 4 indicates the status of the PCI7410 serial EEPROM circuitry. Bit 4 is set
during the loading of the subsystem ID and other default values from the serial bus EEPROM.
0 = Serial EEPROM circuitry is not busy
1 = Serial EEPROM circuitry is busy
3‡
SBDETECT
RW
Serial bus detect. When the serial bus interface is detected through a pullup resistor on the SCL terminal
after reset, this bit is set to 1.
0 = Serial bus interface not detected
1 = Serial bus interface detected
2‡
SBTEST
RW
Serial bus test. When bit 2 is set, the serial bus clock frequency is increased for test purposes.
0 = Serial bus clock at normal operating frequency, 100 kHz (default)
1 = Serial bus clock frequency increased for test purposes
1‡
REQ_ERR
RC
Requested serial bus access error. Bit 1 indicates when a data error occurs on the serial interface during
a requested cycle and may be set due to a missing acknowledge. Bit 1 is cleared by a writeback of 1.
0 = No error detected during user-requested byte read or write cycle
1 = Data error detected during user-requested byte read or write cycle
RC
EEPROM data error status. Bit 0 indicates when a data error occurs on the serial interface during the
auto-load from the serial bus EEPROM and may be set due to a missing acknowledge. Bit 0 is also set on
invalid EEPROM data formats. See Section 3.7.4, Serial Bus EEPROM Application, for details on
EEPROM data format. Bit 0 is cleared by a writeback of 1.
0 = No error detected during auto-load from serial bus EEPROM
1 = Data error detected during auto-load from serial bus EEPROM
0‡
ROM_ERR
‡ One or more bits in this register are cleared only by the assertion of GRST.
4–36
5 ExCA Compatibility Registers (Functions 0 and 1)
The ExCA (exchangeable card architecture) registers implemented in the PCI7410 device are register-compatible
with the Intel 82365SL-DF PCMCIA controller. ExCA registers are identified by an offset value, which is compatible
with the legacy I/O index/data scheme used on the Intel 82365 ISA controller. The ExCA registers are accessed
through this scheme by writing the register offset value into the index register (I/O base), and reading or writing the
data register (I/O base + 1). The I/O base address used in the index/data scheme is programmed in the PC Card 16-bit
I/F legacy mode base address register, which is shared by both card sockets. The offsets from this base address run
contiguously from 00h to 3Fh for socket A, and from 40h to 7Fh for socket B. See Figure 5–1 for an ExCA I/O mapping
illustration. Table 5–1 identifies each ExCA register and its respective ExCA offset.
The PCI7410 device also provides a memory-mapped alias of the ExCA registers by directly mapping them into PCI
memory space. They are located through the CardBus socket registers/ExCA registers base address register (PCI
register 10h) at memory offset 800h. Each socket has a separate base address programmable by function. See
Figure 5–2 for an ExCA memory mapping illustration. Note that memory offsets are 800h–844h for both functions
0 and 1. This illustration also identifies the CardBus socket register mapping, which is mapped into the same 4K
window at memory offset 0h.
The interrupt registers in the ExCA register set, as defined by the 82365SL specification, control such card functions
as reset, type, interrupt routing, and interrupt enables. Special attention must be paid to the interrupt routing registers
and the host interrupt signaling method selected for the PCI7410 device to ensure that all possible PCI7410 interrupts
can potentially be routed to the programmable interrupt controller. The ExCA registers that are critical to the interrupt
signaling are at memory address ExCA offsets 803h and 805h.
Access to I/O mapped 16-bit PC Cards is available to the host system via two ExCA I/O windows. These are regions
of host I/O address space into which the card I/O space is mapped. These windows are defined by start, end, and
offset addresses programmed in the ExCA registers described in this chapter. I/O windows have byte granularity.
Access to memory-mapped 16-bit PC Cards is available to the host system via five ExCA memory windows. These
are regions of host memory space into which the card memory space is mapped. These windows are defined by start,
end, and offset addresses programmed in the ExCA registers described in this chapter. Memory windows have
4-Kbyte granularity.
A bit location followed by a ‡ means that this bit is not cleared by the assertion of PRST. This bit is only cleared by
the assertion of GRST. This is necessary to retain device context during the transition from D3 to D0.
5–1
Host I/O Space
Offset
PCI7410 Configuration Registers
Offset
00h
PC Card A
ExCA
Registers
Card Bus Socket/ExCA Base Address
10h
Index
3Fh
Data
16-Bit Legacy-Mode Base Address
40h
44h
PC Card B
ExCA
Registers
7Fh
Note: The 16-bit legacy-mode base address
register is shared by function 0 and 1 as
indicated by the shading.
Offset of desired register is placed in the index register and the
data from that location is returned in the data register.
Figure 5–1. ExCA Register Access Through I/O
PCI7410 Configuration Registers
Offset
Host
Memory Space
Offset
Host
Memory Space
Offset
00h
CardBus Socket/ExCA Base Address
10h
CardBus
Socket A
Registers
20h
00h
16-Bit Legacy-Mode Base Address
44h
ExCA
Registers
Card A
800h
CardBus
Socket B
Registers
20h
844h
800h
ExCA
Registers
Card B
Note: The CardBus socket/ExCA base
address mode register is separate for
functions 0 and 1.
Offsets are from the CardBus socket/ExCA base
address register’s base address.
Figure 5–2. ExCA Register Access Through Memory
5–2
844h
Table 5–1. ExCA Registers and Offsets
PCI MEMORY ADDRESS
OFFSET (HEX)
EXCA OFFSET
(CARD A)
EXCA OFFSET
(CARD B)
800
00
40
Interface status
801
01
41
Power control †
802†
02
42
Interrupt and general control †
803†
03
43
Card status change †
804†
04
44
Card status change interrupt configuration †
805†
05
45
Address window enable
806
06
46
I / O window control
807
07
47
I / O window 0 start-address low-byte
808
08
48
EXCA REGISTER NAME
Identification and revision ‡
I / O window 0 start-address high-byte
809
09
49
I / O window 0 end-address low-byte
80A
0A
4A
I / O window 0 end-address high-byte
80B
0B
4B
I / O window 1 start-address low-byte
80C
0C
4C
I / O window 1 start-address high-byte
80D
0D
4D
I / O window 1 end-address low-byte
80E
0E
4E
I / O window 1 end-address high-byte
80F
0F
4F
Memory window 0 start-address low-byte
810
10
50
Memory window 0 start-address high-byte
811
11
51
Memory window 0 end-address low-byte
812
12
52
Memory window 0 end-address high-byte
813
13
53
Memory window 0 offset-address low-byte
814
14
54
Memory window 0 offset-address high-byte
815
15
55
Card detect and general control †
816
16
56
Reserved
817
17
57
Memory window 1 start-address low-byte
818
18
58
Memory window 1 start-address high-byte
819
19
59
Memory window 1 end-address low-byte
81A
1A
5A
Memory window 1 end-address high-byte
81B
1B
5B
Memory window 1 offset-address low-byte
81C
1C
5C
Memory window 1 offset-address high-byte
81D
1D
5D
Global control ‡
81E
1E
5E
Reserved
81F
1F
5F
Memory window 2 start-address low-byte
820
20
60
Memory window 2 start-address high-byte
821
21
61
Memory window 2 end-address low-byte
822
22
62
Memory window 2 end-address high-byte
823
23
63
Memory window 2 offset-address low-byte
824
24
64
Memory window 2 offset-address high-byte
825
25
65
† One or more bits in this register are cleared only by the assertion of GRST when PME is enabled. If PME is not enabled, then this bit is cleared
by the assertion of PRST or GRST.
‡ One or more bits in this register are cleared only by the assertion of GRST.
5–3
Table 5–1. ExCA Registers and Offsets (continued)
PCI MEMORY ADDRESS
OFFSET (HEX)
EXCA OFFSET
(CARD A)
EXCA OFFSET
(CARD B)
Reserved
826
26
66
Reserved
827
27
67
Memory window 3 start-address low-byte
828
28
68
EXCA REGISTER NAME
Memory window 3 start-address high-byte
829
29
69
Memory window 3 end-address low-byte
82A
2A
6A
Memory window 3 end-address high-byte
82B
2B
6B
Memory window 3 offset-address low-byte
82C
2C
6C
Memory window 3 offset-address high-byte
82D
2D
6D
Reserved
82E
2E
6E
Reserved
82F
2F
6F
Memory window 4 start-address low-byte
830
30
70
Memory window 4 start-address high-byte
831
31
71
Memory window 4 end-address low-byte
832
32
72
Memory window 4 end-address high-byte
833
33
73
Memory window 4 offset-address low-byte
834
34
74
Memory window 4 offset-address high-byte
835
35
75
I/O window 0 offset-address low-byte
836
36
76
I/O window 0 offset-address high-byte
837
37
77
I/O window 1 offset-address low-byte
838
38
78
I/O window 1 offset-address high-byte
839
39
79
Reserved
83A
3A
7A
Reserved
83B
3B
7B
Reserved
83C
3C
7C
Reserved
83D
3D
7D
Reserved
83E
3E
7E
Reserved
83F
3F
7F
Memory window page register 0
840
–
–
Memory window page register 1
841
–
–
Memory window page register 2
842
–
–
Memory window page register 3
843
–
–
Memory window page register 4
844
–
–
5–4
5.1 ExCA Identification and Revision Register
This register provides host software with information on 16-bit PC Card support and 82365SL-DF compatibility. See
Table 5–2 for a complete description of the register contents.
NOTE: If bit 5 (SUBSYRW) in the system control register is 1, then this register is read-only.
Bit
7
6
5
Type
R
R
RW
RW
Default
1
0
0
0
Name
4
3
2
1
0
RW
RW
RW
RW
0
1
0
0
ExCA identification and revision
Register:
Offset:
ExCA identification and revision
CardBus Socket Address + 800h:
Type:
Default:
Read/Write, Read-only
84h
Card A ExCA Offset 00h
Card B ExCA Offset 40h
Table 5–2. ExCA Identification and Revision Register Description
BIT
SIGNAL
TYPE
FUNCTION
Interface type. These bits, which are hardwired as 10b, identify the 16-bit PC Card support provided by the
PCI7410 device. The PCI7410 device supports both I/O and memory 16-bit PC Cards.
7–6 ‡
IFTYPE
R
5–4 ‡
RSVD
RW
These bits can be used for 82365SL emulation.
3–0 ‡
365REV
RW
82365SL-DF revision. This field stores the Intel 82365SL-DF revision supported by the PCI7410 device. Host
software can read this field to determine compatibility to the 82365SL-DF register set. This field defaults to
0100b upon reset. Writing 0010b to this field puts the controller in the 82356SL mode.
‡ One or more bits in this register are cleared only by the assertion of GRST.
5–5
5.2 ExCA Interface Status Register
This register provides information on current status of the PC Card interface. An X in the default bit values indicates
that the value of the bit after reset depends on the state of the PC Card interface. See Table 5–3 for a complete
description of the register contents.
Bit
7
6
5
Name
4
3
2
1
0
ExCA interface status
Type
R
R
R
R
R
R
R
R
Default
0
0
X
X
X
X
X
X
Register:
Offset:
ExCA interface status
CardBus Socket Address + 801h:
Type:
Default:
Read-only
00XX XXXXb
Card A ExCA Offset 01h
Card B ExCA Offset 41h
Table 5–3. ExCA Interface Status Register Description
BIT
SIGNAL
TYPE
7
RSVD
R
6
CARDPWR
R
5
READY
R
FUNCTION
This bit returns 0 when read. A write has no effect.
CARDPWR. Card power. This bit indicates the current power status of the PC Card socket. This bit reflects
how the ExCA power control register has been programmed. The bit is encoded as:
0 = VCC and VPP to the socket are turned off (default).
1 = VCC and VPP to the socket are turned on.
This bit indicates the current status of the READY signal at the PC Card interface.
4
CARDWP
R
0 = PC Card is not ready for a data transfer.
1 = PC Card is ready for a data transfer.
Card write protect. This bit indicates the current status of the WP signal at the PC Card interface. This signal
reports to the PCI7410 device whether or not the memory card is write protected. Further, write protection
for an entire PCI7410 16-bit memory window is available by setting the appropriate bit in the ExCA memory
window offset-address high-byte register.
0 = WP signal is 0. PC Card is R/W.
1 = WP signal is 1. PC Card is read-only.
3
2
CDETECT2
CDETECT1
R
R
Card detect 2. This bit indicates the status of the CD2 signal at the PC Card interface. Software can use
this and CDETECT1 to determine if a PC Card is fully seated in the socket.
0 = CD2 signal is 1. No PC Card inserted.
1 = CD2 signal is 0. PC Card at least partially inserted.
Card detect 1. This bit indicates the status of the CD1 signal at the PC Card interface. Software can use
this and CDETECT2 to determine if a PC Card is fully seated in the socket.
0 = CD1 signal is 1. No PC Card inserted.
1 = CD1 signal is 0. PC Card at least partially inserted.
Battery voltage detect. When a 16-bit memory card is inserted, the field indicates the status of the battery
voltage detect signals (BVD1, BVD2) at the PC Card interface, where bit 0 reflects the BVD1 status, and
bit 1 reflects BVD2.
1–0
BVDSTAT
R
00 = Battery is dead.
01 = Battery is dead.
10 = Battery is low; warning.
11 = Battery is good.
When a 16-bit I/O card is inserted, this field indicates the status of the SPKR (bit 1) signal and the STSCHG
(bit 0) at the PC Card interface. In this case, the two bits in this field directly reflect the current state of these
card outputs.
5–6
5.3 ExCA Power Control Register
This register provides PC Card power control. Bit 7 of this register enables the 16-bit outputs on the socket interface,
and can be used for power management in 16-bit PC Card applications. See Table 5–5 for a complete description
of the register contents.
Bit
7
6
5
Name
Type
Default
4
3
2
1
0
ExCA power control
RW
R
R
RW
RW
R
RW
RW
0
0
0
0
0
0
0
0
Register:
Offset:
ExCA power control
CardBus Socket Address + 802h:
Type:
Default:
Read-only, Read/Write
00h
Card A ExCA Offset 02h
Card B ExCA Offset 42h
Table 5–4. ExCA Power Control Register Description—82365SL Support
BIT
SIGNAL
TYPE
FUNCTION
Card output enable. Bit 7 controls the state of all of the 16-bit outputs on the PCI7410 device. This bit is
encoded as:
0 = 16-bit PC Card outputs disabled (default)
1 = 16-bit PC Card outputs enabled
7
COE
RW
6
RSVD
R
5†
AUTOPWRSWEN
RW
Auto power switch enable.
0 = Automatic socket power switching based on card detects is disabled.
1 = Automatic socket power switching based on card detects is enabled.
PC Card power enable.
0 = VCC = No connection
1 = VCC is enabled and controlled by bit 2 (EXCAPOWER) of the system control register
(PCI offset 80h, see Section 4.30).
4
CAPWREN
RW
3–2
RSVD
R
1–0
EXCAVPP
RW
Reserved. Bit 6 returns 0 when read.
Reserved. Bits 3 and 2 return 0s when read.
PC Card VPP power control. Bits 1 and 0 are used to request changes to card VPP. The PCI7410 device
ignores this field unless VCC to the socket is enabled. This field is encoded as:
00 = No connection (default)
10 = 12 V
01 = VCC
11 = Reserved
† One or more bits in this register are cleared only by the assertion of GRST when PME is enabled. If PME is not enabled, then this bit is cleared
by the assertion of PRST or GRST.
Table 5–5. ExCA Power Control Register Description—82365SL-DF Support
BIT
SIGNAL
TYPE
FUNCTION
Card output enable. This bit controls the state of all of the 16-bit outputs on the PCI7410 device. This bit
is encoded as:
0 = 16-bit PC Card outputs are disabled (default).
1 = 16-bit PC Card outputs are enabled.
7†
COE
RW
6–5
RSVD
R
4–3 †
EXCAVCC
RW
2
RSVD
R
1–0 †
EXCAVPP
RW
Reserved. These bits return 0s when read. Writes have no effect.
VCC. These bits are used to request changes to card VCC. This field is encoded as:
00 = 0 V (default)
10 = 5 V
01 = 0 V reserved
11 = 3.3 V
This bit returns 0 when read. A write has no effect.
VPP. These bits are used to request changes to card VPP. The PCI7410 device ignores this field unless
VCC to the socket is enabled (i.e., 5 Vdc or 3.3 Vdc). This field is encoded as:
00 = 0 V (default)
10 = 12 V
01 = VCC
11 = 0 V reserved
† This bit is cleared only by the assertion of GRST when PME is enabled. If PME is not enabled, then this bit is cleared by the assertion of PRST
or GRST.
5–7
5.4 ExCA Interrupt and General Control Register
This register controls interrupt routing for I/O interrupts as well as other critical 16-bit PC Card functions. See
Table 5–6 for a complete description of the register contents.
Bit
7
6
5
Name
Type
Default
4
3
2
1
0
ExCA interrupt and general control
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
Register:
Offset:
ExCA interrupt and general control
CardBus Socket Address + 803h:
Type:
Default:
Read/Write
00h
Card A ExCA Offset 03h
Card B ExCA Offset 43h
Table 5–6. ExCA Interrupt and General Control Register Description
BIT
7
SIGNAL
RINGEN
TYPE
FUNCTION
RW
Card ring indicate enable. Enables the ring indicate function of the BVD1/RI terminals. This bit is encoded
as:
0 = Ring indicate disabled (default)
1 = Ring indicate enabled
Card reset. This bit controls the 16-bit PC Card RESET signal, and allows host software to force a card
reset. This bit affects 16-bit cards only. This bit is encoded as:
0 = RESET signal asserted (default)
1 = RESET signal deasserted.
6†
RESET
RW
5†
CARDTYPE
RW
Card type. This bit indicates the PC Card type. This bit is encoded as:
4
CSCROUTE
RW
0 = Memory PC Card is installed (default)
1 = I/O PC Card is installed
PCI interrupt – CSC routing enable bit. This bit has meaning only if the CSC interrupt routing control bit
(PCI offset 93h, bit 5) is 0. In this case, when this bit is set (high), the card status change interrupts are
routed to PCI interrupts. When low, the card status change interrupts are routed using bits 7–4 in the ExCA
card status-change interrupt configuration register (ExCA offset 805h, see Section 5.6). This bit is encoded
as:
0 = CSC interrupts routed by ExCA registers (default)
1 = CSC interrupts routed to PCI interrupts
If the CSC interrupt routing control bit (bit 5) of the diagnostic register (PCI offset 93h, see Section 4.41)
is set to 1, this bit has no meaning, which is the default case.
Card interrupt select for I/O PC Card functional interrupts. These bits select the interrupt routing for I/O
PC Card functional interrupts. This field is encoded as:
3–0
INTSELECT
RW
0000 = No IRQ selected (default). CSC interrupts are routed to PCI Interrupts. This bit setting is ORed
with bit 4 (CSCROUTE) for backward compatibility.
0001 = IRQ1 enabled
0010 = SMI enabled
0011 = IRQ3 enabled
0100 = IRQ4 enabled
0101 = IRQ5 enabled
0110 = IRQ6 enabled
0111 = IRQ7 enabled
1000 = IRQ8 enabled
1001 = IRQ9 enabled
1010 = IRQ10 enabled
1011 = IRQ11 enabled
1100 = IRQ12 enabled
1101 = IRQ13 enabled
1110 = IRQ14 enabled
1111 = IRQ15 enabled
† This bit is cleared only by the assertion of GRST when PME is enabled. If PME is not enabled, then this bit is cleared by the assertion of PRST
or GRST.
5–8
5.5 ExCA Card Status-Change Register
The ExCA card status-change register controls interrupt routing for I/O interrupts and other critical 16-bit PC Card
functions. The register enables these interrupt sources to generate an interrupt to the host. When the interrupt source
is disabled, the corresponding bit in this register always reads 0. When an interrupt source is enabled, the
corresponding bit in this register is set to indicate that the interrupt source is active. After generating the interrupt to
the host, the interrupt service routine must read this register to determine the source of the interrupt. The interrupt
service routine is responsible for resetting the bits in this register as well. Resetting a bit is accomplished by one of
two methods: a read of this register or an explicit writeback of 1 to the status bit. The choice of these two methods
is based on bit 2 (interrupt flag clear mode select) in the ExCA global control register (CB offset 81Eh, see
Section 5.20). See Table 5–7 for a complete description of the register contents.
Bit
7
6
5
Type
R
R
R
R
Default
0
0
0
0
Name
4
3
2
1
0
R
R
R
R
0
0
0
0
ExCA card status-change
Register:
Type:
Offset:
Default:
ExCA card status-change
Read-only
CardBus socket address + 804h; Card A ExCA offset 04h
Card B ExCA offset 44h
00h
Table 5–7. ExCA Card Status-Change Register Description
BIT
SIGNAL
TYPE
7–4
RSVD
R
Reserved. Bits 7–4 return 0s when read.
R
Card detect change. Bit 3 indicates whether a change on CD1 or CD2 occurred at the PC Card
interface. This bit is encoded as:
0 = No change detected on either CD1 or CD2
1 = Change detected on either CD1 or CD2
3†
2†
CDCHANGE
READYCHANGE
R
FUNCTION
Ready change. When a 16-bit memory is installed in the socket, bit 2 includes whether the source of
a PCI7410 interrupt was due to a change on READY at the PC Card interface, indicating that the
PC Card is now ready to accept new data. This bit is encoded as:
0 = No low-to-high transition detected on READY (default)
1 = Detected low-to-high transition on READY
When a 16-bit I/O card is installed, bit 2 is always 0.
1†
BATWARN
R
Battery warning change. When a 16-bit memory card is installed in the socket, bit 1 indicates whether
the source of a PCI7410 interrupt was due to a battery-low warning condition. This bit is encoded as:
0 = No battery warning condition (default)
1 = Detected battery warning condition
When a 16-bit I/O card is installed, bit 1 is always 0.
0†
BATDEAD
R
Battery dead or status change. When a 16-bit memory card is installed in the socket, bit 0 indicates
whether the source of a PCI7410 interrupt was due to a battery dead condition. This bit is encoded as:
0 = STSCHG deasserted (default)
1 = STSCHG asserted
Ring indicate. When the PCI7410 is configured for ring indicate operation, bit 0 indicates the status of
RI.
† These are PME context bits and can be cleared only by the assertion of GRST when PME is enabled. If PME is not enabled, then these bits are
cleared by the assertion of PRST or GRST.
5–9
5.6 ExCA Card Status-Change Interrupt Configuration Register
This register controls interrupt routing for CSC interrupts, as well as masks/unmasks CSC interrupt sources. See
Table 5–8 for a complete description of the register contents.
Bit
7
6
5
Name
Type
Default
4
3
2
1
0
ExCA card status-change interrupt configuration
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
ExCA card status-change interrupt configuration
CardBus Socket Address + 805h:
Card A ExCA Offset 05h
Card B ExCA Offset 45h
Read/Write
00h
Table 5–8. ExCA Card Status-Change Interrupt Configuration Register Description
BIT
SIGNAL
TYPE
FUNCTION
Interrupt select for card status change. These bits select the interrupt routing for card status-change
interrupts. This field is encoded as:
7–4
CSCSELECT
RW
3†
CDEN
RW
0000 = CSC interrupts routed to PCI interrupts if bit 5 of the diagnostic register (PCI offset 93h) is set
to 1b. In this case bit 4 of ExCA 803 is a don’t care. This is the default setting.
0000 = No ISA interrupt routing if bit 5 of the diagnostic register (PCI offset 93h) is set to 0b. In this case,
CSC interrupts are routed to PCI interrupts by setting bit 4 of ExCA 803h to 1b.
0001 = IRQ1 enabled
0010 = SMI enabled
0011 = IRQ3 enabled
0100 = IRQ4 enabled
0101 = IRQ5 enabled
0110 = IRQ6 enabled
0111 = IRQ7 enabled
1000 = IRQ8 enabled
1001 = IRQ9 enabled
1010 = IRQ10 enabled
1011 = IRQ11 enabled
1100 = IRQ12 enabled
1101 = IRQ13 enabled
1110 = IRQ14 enabled
1111 = IRQ15 enabled
Card detect enable. Enables interrupts on CD1 or CD2 changes. This bit is encoded as:
2†
1†
0†
READYEN
BATWARNEN
BATDEADEN
RW
RW
RW
0 = Disables interrupts on CD1 or CD2 line changes (default)
1 = Enables interrupts on CD1 or CD2 line changes
Ready enable. This bit enables/disables a low-to-high transition on the PC Card READY signal to generate
a host interrupt. This interrupt source is considered a card status change. This bit is encoded as:
0 = Disables host interrupt generation (default)
1 = Enables host interrupt generation
Battery warning enable. This bit enables/disables a battery warning condition to generate a CSC interrupt.
This bit is encoded as:
0 = Disables host interrupt generation (default)
1 = Enables host interrupt generation
Battery dead enable. This bit enables/disables a battery dead condition on a memory PC Card or assertion
of the STSCHG I/O PC Card signal to generate a CSC interrupt.
0 = Disables host interrupt generation (default)
1 = Enables host interrupt generation
† This bit is cleared only by the assertion of GRST when PME is enabled. If PME is not enabled, then this bit is cleared by the assertion of PRST
or GRST.
5–10
5.7 ExCA Address Window Enable Register
The ExCA address window enable register enables/disables the memory and I/O windows to the 16-bit PC Card. By
default, all windows to the card are disabled. The PCI7410 device does not acknowledge PCI memory or I/O cycles
to the card if the corresponding enable bit in this register is 0, regardless of the programming of the memory or I/O
window start/end/offset address registers. See Table 5–9 for a complete description of the register contents.
Bit
7
6
5
RW
RW
R
RW
0
0
0
0
Name
Type
Default
4
3
2
1
0
RW
RW
RW
RW
0
0
0
0
ExCA address window enable
Register:
Type:
Offset:
Default:
ExCA address window enable
Read-only, Read/Write
CardBus socket address + 806h; Card A ExCA offset 06h
Card B ExCA offset 46h
00h
Table 5–9. ExCA Address Window Enable Register Description
BIT
SIGNAL
TYPE
FUNCTION
7
IOWIN1EN
RW
I/O window 1 enable. Bit 7 enables/disables I/O window 1 for the PC Card. This bit is encoded as:
0 = I/O window 1 disabled (default)
1 = I/O window 1 enabled
6
IOWIN0EN
RW
I/O window 0 enable. Bit 6 enables/disables I/O window 0 for the PC Card. This bit is encoded as:
0 = I/O window 0 disabled (default)
1 = I/O window 0 enabled
5
RSVD
R
4
3
MEMWIN4EN
MEMWIN3EN
Reserved. Bit 5 returns 0 when read.
RW
Memory window 4 enable. Bit 4 enables/disables memory window 4 for the PC Card. This bit is
encoded as:
0 = Memory window 4 disabled (default)
1 = Memory window 4 enabled
RW
Memory window 3 enable. Bit 3 enables/disables memory window 3 for the PC Card. This bit is
encoded as:
0 = Memory window 3 disabled (default)
1 = Memory window 3 enabled
2
MEMWIN2EN
RW
Memory window 2 enable. Bit 2 enables/disables memory window 2 for the PC Card. This bit is
encoded as:
0 = Memory window 2 disabled (default)
1 = Memory window 2 enabled
1
MEMWIN1EN
RW
Memory window 1 enable. Bit 1 enables/disables memory window 1 for the PC Card. This bit is
encoded as:
0 = Memory window 1 disabled (default)
1 = Memory window 1 enabled
0
MEMWIN0EN
RW
Memory window 0 enable. Bit 0 enables/disables memory window 0 for the PC Card. This bit is
encoded as:
0 = Memory window 0 disabled (default)
1 = Memory window 0 enabled
5–11
5.8 ExCA I/O Window Control Register
The ExCA I/O window control register contains parameters related to I/O window sizing and cycle timing. See
Table 5–10 for a complete description of the register contents.
Bit
7
6
5
RW
RW
RW
RW
0
0
0
0
Name
Type
Default
4
3
2
1
0
RW
RW
RW
RW
0
0
0
0
ExCA I/O window control
Register:
Type:
Offset:
Default:
ExCA I/O window control
Read/Write
CardBus socket address + 807h: Card A ExCA offset 07h
Card B ExCA offset 47h
00h
Table 5–10. ExCA I/O Window Control Register Description
BIT
7
6
5
4
3
2
1
0
5–12
SIGNAL
WAITSTATE1
ZEROWS1
IOSIS16W1
DATASIZE1
WAITSTATE0
ZEROWS0
IOSIS16W0
DATASIZE0
TYPE
FUNCTION
RW
I/O window 1 wait state. Bit 7 controls the I/O window 1 wait state for 16-bit I/O accesses. Bit 7 has no effect
on 8-bit accesses. This wait-state timing emulates the ISA wait state used by the Intel 82365SL-DF. This
bit is encoded as:
0 = 16-bit cycles have standard length (default).
1 = 16-bit cycles are extended by one equivalent ISA wait state.
RW
I/O window 1 zero wait state. Bit 6 controls the I/O window 1 wait state for 8-bit I/O accesses. Bit 6 has
no effect on 16-bit accesses. This wait-state timing emulates the ISA wait state used by the Intel
82365SL-DF. This bit is encoded as:
0 = 8-bit cycles have standard length (default).
1 = 8-bit cycles are reduced to equivalent of three ISA cycles.
RW
I/O window 1 IOIS16 source. Bit 5 controls the I/O window 1 automatic data-sizing feature that uses IOIS16
from the PC Card to determine the data width of the I/O data transfer. This bit is encoded as:
0 = Window data width determined by DATASIZE1, bit 4 (default).
1 = Window data width determined by IOIS16.
RW
I/O window 1 data size. Bit 4 controls the I/O window 1 data size. Bit 4 is ignored if bit 5 (IOSIS16W1) is
set. This bit is encoded as:
0 = Window data width is 8 bits (default).
1 = Window data width is 16 bits.
RW
I/O window 0 wait state. Bit 3 controls the I/O window 0 wait state for 16-bit I/O accesses. Bit 3 has no effect
on 8-bit accesses. This wait-state timing emulates the ISA wait state used by the Intel 82365SL-DF. This
bit is encoded as:
0 = 16-bit cycles have standard length (default).
1 = 16-bit cycles are extended by one equivalent ISA wait state.
RW
I/O window 0 zero wait state. Bit 2 controls the I/O window 0 wait state for 8-bit I/O accesses. Bit 2 has
no effect on 16-bit accesses. This wait-state timing emulates the ISA wait state used by the Intel
82365SL-DF. This bit is encoded as:
0 = 8-bit cycles have standard length (default).
1 = 8-bit cycles are reduced to equivalent of three ISA cycles.
RW
I/O window 0 IOIS16 source. Bit 1 controls the I/O window 0 automatic data sizing feature that uses IOIS16
from the PC Card to determine the data width of the I/O data transfer. This bit is encoded as:
0 = Window data width is determined by DATASIZE0, bit 0 (default).
1 = Window data width is determined by IOIS16.
RW
I/O window 0 data size. Bit 0 controls the I/O window 0 data size. Bit 0 is ignored if bit 1 (IOSIS16W0) is
set. This bit is encoded as:
0 = Window data width is 8 bits (default).
1 = Window data width is 16 bits.
5.9 ExCA I/O Windows 0 and 1 Start-Address Low-Byte Registers
These registers contain the low byte of the 16-bit I/O window start address for I/O windows 0 and 1. The 8 bits of these
registers correspond to the lower 8 bits of the start address.
Bit
7
6
Name
Type
Default
5
4
3
2
1
0
ExCA I/O windows 0 and 1 start-address low-byte
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
Register:
Offset:
Register:
Offset:
Type:
Default:
ExCA I/O window 0 start-address low-byte
CardBus Socket Address + 808h:
Card A ExCA Offset 08h
Card B ExCA Offset 48h
ExCA I/O window 1 start-address low-byte
CardBus Socket Address + 80Ch:
Card A ExCA Offset 0Ch
Card B ExCA Offset 4Ch
Read/Write
00h
5.10 ExCA I/O Windows 0 and 1 Start-Address High-Byte Registers
These registers contain the high byte of the 16-bit I/O window start address for I/O windows 0 and 1. The 8 bits of
these registers correspond to the upper 8 bits of the start address.
Bit
7
6
5
RW
RW
RW
RW
RW
0
0
0
0
0
Name
Type
Default
4
3
2
1
0
RW
RW
RW
0
0
0
ExCA I/O windows 0 and 1 start-address high-byte
Register:
Offset:
Register:
Offset:
Type:
Default:
ExCA I/O window 0 start-address high-byte
CardBus Socket Address + 809h:
Card A ExCA Offset 09h
Card B ExCA Offset 49h
ExCA I/O window 1 start-address high-byte
CardBus Socket Address + 80Dh:
Card A ExCA Offset 0Dh
Card B ExCA Offset 4Dh
Read/Write
00h
5–13
5.11 ExCA I/O Windows 0 and 1 End-Address Low-Byte Registers
These registers contain the low byte of the 16-bit I/O window end address for I/O windows 0 and 1. The 8 bits of these
registers correspond to the lower 8 bits of the start address.
Bit
7
6
Name
Type
Default
5
4
3
2
1
0
ExCA I/O windows 0 and 1 end-address low-byte
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
Register:
Offset:
Register:
Offset:
Type:
Default:
ExCA I/O window 0 end-address low-byte
CardBus Socket Address + 80Ah:
Card A ExCA Offset 0Ah
Card B ExCA Offset 4Ah
ExCA I/O window 1 end-address low-byte
CardBus Socket Address + 80Eh:
Card A ExCA Offset 0Eh
Card B ExCA Offset 4Eh
Read/Write
00h
5.12 ExCA I/O Windows 0 and 1 End-Address High-Byte Registers
These registers contain the high byte of the 16-bit I/O window end address for I/O windows 0 and 1. The 8 bits of these
registers correspond to the upper 8 bits of the end address.
Bit
7
6
5
RW
RW
RW
RW
RW
0
0
0
0
0
Name
Type
Default
3
2
1
0
RW
RW
RW
0
0
0
ExCA I/O windows 0 and 1 end-address high-byte
Register:
Offset:
Register:
Offset:
Type:
Default:
5–14
4
ExCA I/O window 0 end-address high-byte
CardBus Socket Address + 80Bh:
Card A ExCA Offset 0Bh
Card B ExCA Offset 4Bh
ExCA I/O window 1 end-address high-byte
CardBus Socket Address + 80Fh:
Card A ExCA Offset 0Fh
Card B ExCA Offset 4Fh
Read/Write
00h
5.13 ExCA Memory Windows 0–4 Start-Address Low-Byte Registers
These registers contain the low byte of the 16-bit memory window start address for memory windows 0, 1, 2, 3, and 4.
The 8 bits of these registers correspond to bits A19–A12 of the start address.
Bit
7
6
Name
Type
Default
5
4
3
2
1
0
ExCA memory windows 0–4 start-address low-byte
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
Register:
Offset:
Register:
Offset:
Register:
Offset:
Register:
Offset:
Register:
Offset:
Type:
Default:
ExCA memory window 0 start-address low-byte
CardBus Socket Address + 810h:
Card A ExCA Offset 10h
Card B ExCA Offset 50h
ExCA memory window 1 start-address low-byte
CardBus Socket Address + 818h:
Card A ExCA Offset 18h
Card B ExCA Offset 58h
ExCA memory window 2 start-address low-byte
CardBus Socket Address + 820h:
Card A ExCA Offset 20h
Card B ExCA Offset 60h
ExCA memory window 3 start-address low-byte
CardBus Socket Address + 828h:
Card A ExCA Offset 28h
Card B ExCA Offset 68h
ExCA memory window 4 start-address low-byte
CardBus Socket Address + 830h:
Card A ExCA Offset 30h
Card B ExCA Offset 70h
Read/Write
00h
5–15
5.14 ExCA Memory Windows 0–4 Start-Address High-Byte Registers
These registers contain the high nibble of the 16-bit memory window start address for memory windows 0, 1, 2, 3,
and 4. The lower 4 bits of these registers correspond to bits A23–A20 of the start address. In addition, the memory
window data width and wait states are set in this register. See Table 5–11 for a complete description of the register
contents.
Bit
7
6
Name
Type
Default
5
4
3
2
1
0
ExCA memory windows 0–4 start-address high-byte
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
Register:
Offset:
Register:
Offset:
Register:
Offset:
Register:
Offset:
Register:
Offset:
Type:
Default:
ExCA memory window 0 start-address high-byte
CardBus Socket Address + 811h:
Card A ExCA Offset 11h
Card B ExCA Offset 51h
ExCA memory window 1 start-address high-byte
CardBus Socket Address + 819h:
Card A ExCA Offset 19h
Card B ExCA Offset 59h
ExCA memory window 2 start-address high-byte
CardBus Socket Address + 821h:
Card A ExCA Offset 21h
Card B ExCA Offset 61h
ExCA memory window 3 start-address high-byte
CardBus Socket Address + 829h:
Card A ExCA Offset 29h
Card B ExCA Offset 69h
ExCA memory window 4 start-address high-byte
CardBus Socket Address + 831h:
Card A ExCA Offset 31h
Card B ExCA Offset 71h
Read/Write
00h
Table 5–11. ExCA Memory Windows 0–4 Start-Address High-Byte Registers Description
BIT
SIGNAL
TYPE
7
DATASIZE
RW
FUNCTION
This bit controls the memory window data width. This bit is encoded as:
0 = Window data width is 8 bits (default)
1 = Window data width is 16 bits
Zero wait-state. This bit controls the memory window wait state for 8- and 16-bit accesses. This wait-state
timing emulates the ISA wait state used by the 82365SL-DF. This bit is encoded as:
5–16
6
ZEROWAIT
RW
5–4
SCRATCH
RW
Scratch pad bits. These bits have no effect on memory window operation.
3–0
STAHN
RW
Start address high-nibble. These bits represent the upper address bits A23–A20 of the memory window
start address.
0 = 8- and 16-bit cycles have standard length (default).
1 = 8-bit cycles reduced to equivalent of three ISA cycles
16-bit cycles reduced to the equivalent of two ISA cycles
5.15 ExCA Memory Windows 0–4 End-Address Low-Byte Registers
These registers contain the low byte of the 16-bit memory window end address for memory windows 0, 1, 2, 3, and 4.
The 8 bits of these registers correspond to bits A19–A12 of the end address.
Bit
7
6
Name
Type
Default
5
4
3
2
1
0
ExCA memory windows 0–4 end-address low-byte
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
Register:
Offset:
Register:
Offset:
Register:
Offset:
Register:
Offset:
Register:
Offset:
Type:
Default:
ExCA memory window 0 end-address low-byte
CardBus Socket Address + 812h:
Card A ExCA Offset 12h
Card B ExCA Offset 52h
ExCA memory window 1 end-address low-byte
CardBus Socket Address + 81Ah:
Card A ExCA Offset 1Ah
Card B ExCA Offset 5Ah
ExCA memory window 2 end-address low-byte
CardBus Socket Address + 822h:
Card A ExCA Offset 22h
Card B ExCA Offset 62h
ExCA memory window 3 end-address low-byte
CardBus Socket Address + 82Ah:
Card A ExCA Offset 2Ah
Card B ExCA Offset 6Ah
ExCA memory window 4 end-address low-byte
CardBus Socket Address + 832h:
Card A ExCA Offset 32h
Card B ExCA Offset 72h
Read/Write
00h
5–17
5.16 ExCA Memory Windows 0–4 End-Address High-Byte Registers
These registers contain the high nibble of the 16-bit memory window end address for memory windows 0, 1, 2, 3,
and 4. The lower 4 bits of these registers correspond to bits A23–A20 of the end address. In addition, the memory
window wait states are set in this register. See Table 5–12 for a complete description of the register contents.
Bit
7
6
Name
Type
Default
5
4
3
2
1
0
ExCA memory windows 0–4 end-address high-byte
RW
RW
R
R
RW
RW
RW
RW
0
0
0
0
0
0
0
0
Register:
Offset:
Register:
Offset:
Register:
Offset:
Register:
Offset:
Register:
Offset:
Type:
Default:
ExCA memory window 0 end-address high-byte
CardBus Socket Address + 813h:
Card A ExCA Offset 13h
Card B ExCA Offset 53h
ExCA memory window 1 end-address high-byte
CardBus Socket Address + 81Bh:
Card A ExCA Offset 1Bh
Card B ExCA Offset 5Bh
ExCA memory window 2 end-address high-byte
CardBus Socket Address + 823h:
Card A ExCA Offset 23h
Card B ExCA Offset 63h
ExCA memory window 3 end-address high-byte
CardBus Socket Address + 82Bh:
Card A ExCA Offset 2Bh
Card B ExCA Offset 6Bh
ExCA Memory window 4 end-address high-byte
CardBus Socket Address + 833h:
Card A ExCA Offset 33h
Card B ExCA Offset 73h
Read/Write, Read-only
00h
Table 5–12. ExCA Memory Windows 0–4 End-Address High-Byte Registers Description
5–18
BIT
SIGNAL
TYPE
FUNCTION
7–6
MEMWS
RW
Wait state. These bits specify the number of equivalent ISA wait states to be added to 16-bit memory
accesses. The number of wait states added is equal to the binary value of these 2 bits.
5–4
RSVD
R
3–0
ENDHN
RW
Reserved. These bits return 0s when read. Writes have no effect.
End-address high nibble. These bits represent the upper address bits A23–A20 of the memory window end
address.
5.17 ExCA Memory Windows 0–4 Offset-Address Low-Byte Registers
These registers contain the low byte of the 16-bit memory window offset address for memory windows 0, 1, 2, 3,
and 4. The 8 bits of these registers correspond to bits A19–A12 of the offset address.
Bit
7
6
Name
Type
Default
5
4
3
2
1
0
ExCA memory windows 0–4 offset-address low-byte
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
Register:
Offset:
Register:
Offset:
Register:
Offset:
Register:
Offset:
Register:
Offset:
Type:
Default:
ExCA memory window 0 offset-address low-byte
CardBus Socket Address + 814h:
Card A ExCA Offset 14h
Card B ExCA Offset 54h
ExCA memory window 1 offset-address low-byte
CardBus Socket Address + 81Ch:
Card A ExCA Offset 1Ch
Card B ExCA Offset 5Ch
ExCA memory window 2 offset-address low-byte
CardBus Socket Address + 824h:
Card A ExCA Offset 24h
Card B ExCA Offset 64h
ExCA memory window 3 offset-address low-byte
CardBus Socket Address + 82Ch:
Card A ExCA Offset 2Ch
Card B ExCA Offset 6Ch
ExCA memory window 4 offset-address low-byte
CardBus Socket Address + 834h:
Card A ExCA Offset 34h
Card B ExCA Offset 74h
Read/Write
00h
5–19
5.18 ExCA Memory Windows 0–4 Offset-Address High-Byte Registers
These registers contain the high 6 bits of the 16-bit memory window offset address for memory windows 0, 1, 2, 3,
and 4. The lower 6 bits of these registers correspond to bits A25–A20 of the offset address. In addition, the write
protection and common/attribute memory configurations are set in this register. See Table 5–13 for a complete
description of the register contents.
Bit
7
6
Name
Type
Default
5
4
3
2
1
0
ExCA memory window 0–4 offset-address high-byte
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
Register:
Offset:
Register:
Offset:
Register:
Offset:
Register:
Offset:
Register:
Offset:
Type:
Default:
ExCA memory window 0 offset-address high-byte
CardBus Socket Address + 815h:
Card A ExCA Offset 15h
Card B ExCA Offset 55h
ExCA memory window 1 offset-address high-byte
CardBus Socket Address + 81Dh:
Card A ExCA Offset 1Dh
Card B ExCA Offset 5Dh
ExCA memory window 2 offset-address high-byte
CardBus Socket Address + 825h:
Card A ExCA Offset 25h
Card B ExCA Offset 65h
ExCA memory window 3 offset-address high-byte
CardBus Socket Address + 82Dh:
Card A ExCA Offset 2Dh
Card B ExCA Offset 6Dh
ExCA memory window 4 offset-address high-byte
CardBus Socket Address + 835h:
Card A ExCA Offset 35h
Card B ExCA Offset 75h
Read/Write
00h
Table 5–13. ExCA Memory Windows 0–4 Offset-Address High-Byte Registers Description
BIT
7
5–20
SIGNAL
WINWP
TYPE
RW
6
REG
RW
5–0
OFFHB
RW
FUNCTION
Write protect. This bit specifies whether write operations to this memory window are enabled.
This bit is encoded as:
0 = Write operations are allowed (default).
1 = Write operations are not allowed.
This bit specifies whether this memory window is mapped to card attribute or common memory.
This bit is encoded as:
0 = Memory window is mapped to common memory (default).
1 = Memory window is mapped to attribute memory.
Offset-address high byte. These bits represent the upper address bits A25–A20 of the memory window offset
address.
5.19 ExCA Card Detect and General Control Register
This register controls how the ExCA registers for the socket respond to card removal. It also reports the status of the
VS1 and VS2 signals at the PC Card interface. Table 5–14 describes each bit in the ExCA card detect and general
control register.
Bit
7
6
5
Name
4
3
2
1
0
ExCA card detect and general control
Type
R
R
W
RW
R
R
RW
R
Default
X
X
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
ExCA card detect and general control
CardBus Socket Address + 816h:
Card A ExCA Offset 16h
Card B ExCA Offset 56h
Read-only, Write-only, Read/Write
XX00 0000b
Table 5–14. ExCA Card Detect and General Control Register Description
BIT
7†
6†
SIGNAL
VS2STAT
VS1STAT
TYPE
R
R
FUNCTION
VS2. This bit reports the current state of the VS2 signal at the PC Card interface, and, therefore, does not
have a default value.
0 = VS2 is low.
1 = VS2 is high.
VS1. This bit reports the current state of the VS1 signal at the PC Card interface, and, therefore, does not
have a default value.
0 = VS1 is low.
1 = VS1 is high.
Software card detect interrupt. If card detect enable, bit 3 in the ExCA card status change interrupt
configuration register (ExCA offset 805h, see Section 5.6) is set, then writing a 1 to this bit causes a
card-detect card-status-change interrupt for the associated card socket.
5
SWCSC
W
If the card-detect enable bit is cleared to 0 in the ExCA card status-change interrupt configuration register
(ExCA offset 805h, see Section 5.6), then writing a 1 to the software card-detect interrupt bit has no effect.
This bit is write-only.
A read operation of this bit always returns 0. Writing a 1 to this bit also clears it. If bit 2 of the ExCA global
control register (ExCA offset 81Eh, see Section 5.20) is set and a 1 is written to clear bit 3 of the ExCA
card status change interrupt register, then this bit also is cleared.
4
CDRESUME
RW
Card detect resume enable. If this bit is set to 1 and a card detect change has been detected on the CD1
and CD2 inputs, then the RI_OUT output goes from high to low. The RI_OUT remains low until the card
status change bit in the ExCA card status-change register (ExCA offset 804h, see Section 5.5) is cleared.
If this bit is a 0, then the card detect resume functionality is disabled.
0 = Card detect resume disabled (default)
1 = Card detect resume enabled
3–2
RSVD
R
1
REGCONFIG
RW
0
RSVD
R
These bits return 0s when read. Writes have no effect.
Register configuration upon card removal. This bit controls how the ExCA registers for the socket react
to a card removal event. This bit is encoded as:
0 = No change to ExCA registers upon card removal (default)
1 = Reset ExCA registers upon card removal
This bit returns 0 when read. A write has no effect.
† One or more bits in this register are cleared only by the assertion of GRST when PME is enabled. If PME is not enabled, then this bit is cleared
by the assertion of PRST or GRST.
5–21
5.20 ExCA Global Control Register
This register controls both PC Card sockets, and is not duplicated for each socket. The host interrupt mode bits in
this register are retained for 82365SL-DF compatibility. See Table 5–15 for a complete description of the register
contents.
Bit
7
6
5
Name
4
3
2
1
0
ExCA global control
Type
R
R
R
RW
RW
RW
RW
RW
Default
0
0
0
0
0
0
0
0
Register:
Offset:
ExCA global control
CardBus Socket Address + 81Eh:
Type:
Default:
Read-only, Read/Write
00h
Card A ExCA Offset 1Eh
Card B ExCA Offset 5Eh
Table 5–15. ExCA Global Control Register Description
BIT
SIGNAL
TYPE
7–5
RSVD
R
4
3
2‡
1‡
0‡
INTMODEB
INTMODEA
IFCMODE
CSCMODE
PWRDWN
RW
RW
RW
RW
RW
FUNCTION
These bits return 0s when read. Writes have no effect.
Level/edge interrupt mode select, card B. This bit selects the signaling mode for the PCI7410 host interrupt
for card B interrupts. This bit is encoded as:
0 = Host interrupt is edge mode (default).
1 = Host interrupt is level mode.
Level/edge interrupt mode select, card A. This bit selects the signaling mode for the PCI7410 host interrupt
for card A interrupts. This bit is encoded as:
0 = Host interrupt is edge-mode (default).
1 = Host interrupt is level-mode.
Interrupt flag clear mode select. This bit selects the interrupt flag clear mechanism for the flags in the ExCA
card status change register. This bit is encoded as:
0 = Interrupt flags cleared by read of CSC register (default)
1 = Interrupt flags cleared by explicit writeback of 1
Card status change level/edge mode select. This bit selects the signaling mode for the PCI7410 host
interrupt for card status changes. This bit is encoded as:
0 = Host interrupt is edge-mode (default).
1 = Host interrupt is level-mode.
Power-down mode select. When this bit is set to 1, the PCI7410 device is in power-down mode. In
power-down mode the PCI7410 card outputs are placed in a high-impedance state until an active cycle
is executed on the card interface. Following an active cycle the outputs are again placed in a
high-impedance state. The PCI7410 device still receives functional interrupts and/or card status change
interrupts; however, an actual card access is required to wake up the interface. This bit is encoded as:
0 = Power-down mode disabled (default)
1 = Power-down mode enabled
‡ One or more bits in this register are cleared only by the assertion of GRST.
5–22
5.21 ExCA I/O Windows 0 and 1 Offset-Address Low-Byte Registers
These registers contain the low byte of the 16-bit I/O window offset address for I/O windows 0 and 1. The 8 bits of
these registers correspond to the lower 8 bits of the offset address, and bit 0 is always 0.
Bit
7
6
Name
Type
Default
5
4
3
2
1
0
ExCA I/O windows 0 and 1 offset-address low-byte
RW
RW
RW
RW
RW
RW
RW
R
0
0
0
0
0
0
0
0
Register:
Offset:
Register:
Offset:
Type:
Default:
ExCA I/O window 0 offset-address low-byte
CardBus Socket Address + 836h:
Card A ExCA Offset 36h
Card B ExCA Offset 76h
ExCA I/O window 1 offset-address low-byte
CardBus Socket Address + 838h:
Card A ExCA Offset 38h
Card B ExCA Offset 78h
Read/Write, Read-only
00h
5.22 ExCA I/O Windows 0 and 1 Offset-Address High-Byte Registers
These registers contain the high byte of the 16-bit I/O window offset address for I/O windows 0 and 1. The 8 bits of
these registers correspond to the upper 8 bits of the offset address.
Bit
7
6
5
RW
RW
RW
RW
RW
0
0
0
0
0
Name
Type
Default
4
3
2
1
0
RW
RW
RW
0
0
0
ExCA I/O windows 0 and 1 offset-address high-byte
Register:
Offset:
Register:
Offset:
Type:
Default:
ExCA I/O window 0 offset-address high-byte
CardBus Socket Address + 837h:
Card A ExCA Offset 37h
Card B ExCA Offset 77h
ExCA I/O window 1 offset-address high-byte
CardBus Socket Address + 839h:
Card A ExCA Offset 39h
Card B ExCA Offset 79h
Read/Write
00h
5–23
5.23 ExCA Memory Windows 0–4 Page Registers
The upper 8 bits of a 4-byte PCI memory address are compared to the contents of this register when decoding
addresses for 16-bit memory windows. Each window has its own page register, all of which default to 00h. By
programming this register to a nonzero value, host software can locate 16-bit memory windows in any one of 256
16-Mbyte regions in the 4-gigabyte PCI address space. These registers are only accessible when the ExCA registers
are memory-mapped, that is, these registers may not be accessed using the index/data I/O scheme.
Bit
7
6
5
Name
Type
Default
3
2
1
0
RW
RW
RW
RW
RW
RW
RW
R
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
5–24
4
ExCA memory windows 0–4 page
ExCA memory windows 0–4 page
CardBus Socket Address + 840h, 841h, 842h, 843h, 844h
Read/Write
00h
6 CardBus Socket Registers (Functions 0 and 1)
The 1997 PC Card Standard requires a CardBus socket controller to provide five 32-bit registers that report and
control socket-specific functions. The PCI7410 device provides the CardBus socket/ExCA base address register
(PCI offset 10h, see Section 4.13) to locate these CardBus socket registers in PCI memory address space. Each
function has a separate base address register for accessing the CardBus socket registers (see Figure 6–1).
Table 6–1 gives the location of the socket registers in relation to the CardBus socket/ExCA base address.
In addition to the five required registers, the PCI7410 device implements a register at offset 20h that provides power
management control for the socket.
PCI7410 Configuration Registers
Offset
Host
Memory Space
Offset
Host
Memory Space
Offset
00h
CardBus Socket/ExCA Base Address
10h
CardBus
Socket A
Registers
20h
00h
16-Bit Legacy-Mode Base Address
44h
ExCA
Registers
Card A
800h
CardBus
Socket B
Registers
20h
844h
800h
ExCA
Registers
Card B
Note: The CardBus socket/ExCA base
address mode register is separate for
functions 0 and 1.
844h
Offsets are from the CardBus socket/ExCA base
address register’s base address.
Figure 6–1. Accessing CardBus Socket Registers Through PCI Memory
Table 6–1. CardBus Socket Registers
REGISTER NAME
OFFSET
Socket event †
00h
Socket mask †
04h
Socket present state †
08h
Socket force event
0Ch
Socket control †
Reserved
10h
14h–1Ch
Socket power management ‡
20h
† One or more bits in the register are PME context bits and can be cleared only by the assertion of GRST when PME is enabled. If PME is not
enabled, then these bits are cleared by the assertion of PRST or GRST.
‡ One or more bits in this register are cleared only by the assertion of GRST.
6–1
6.1 Socket Event Register
This register indicates a change in socket status has occurred. These bits do not indicate what the change is, only
that one has occurred. Software must read the socket present state register for current status. Each bit in this register
can be cleared by writing a 1 to that bit. The bits in this register can be set to a 1 by software through writing a 1 to
the corresponding bit in the socket force event register. All bits in this register are cleared by PCI reset. They can be
immediately set again, if, when coming out of PC Card reset, the bridge finds the status unchanged (i.e., CSTSCHG
reasserted or card detect is still true). Software needs to clear this register before enabling interrupts. If it is not cleared
and interrupts are enabled, then an unmasked interrupt is generated based on any bit that is set. See Table 6–2 for
a complete description of the register contents.
Bit
31
30
29
28
27
26
25
Name
24
23
22
21
20
19
18
17
16
Socket event
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Socket event
Type
R
R
R
R
R
R
R
R
R
R
R
R
RWC
RWC
RWC
RWC
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Socket event
CardBus Socket Address + 00h
Read-only, Read/Write to Clear
0000 0000h
Table 6–2. Socket Event Register Description
BIT
SIGNAL
TYPE
31–4
RSVD
R
3†
PWREVENT
RWC
Power cycle. This bit is set when the PCI7410 device detects that the PWRCYCLE bit in the socket present
state register (offset 08h, see Section 6.3) has changed. This bit is cleared by writing a 1.
2†
CD2EVENT
RWC
CCD2. This bit is set when the PCI7410 device detects that the CDETECT2 field in the socket present state
register (offset 08h, see Section 6.3) has changed. This bit is cleared by writing a 1.
1†
CD1EVENT
RWC
CCD1. This bit is set when the PCI7410 device detects that the CDETECT1 field in the socket present state
register (offset 08h, see Section 6.3) has changed. This bit is cleared by writing a 1.
RWC
CSTSCHG. This bit is set when the CARDSTS field in the socket present state register (offset 08h, see
Section 6.3) has changed state. For CardBus cards, this bit is set on the rising edge of the CSTSCHG
signal. For 16-bit PC Cards, this bit is set on both transitions of the CSTSCHG signal. This bit is reset by
writing a 1.
0†
CSTSEVENT
FUNCTION
These bits return 0s when read.
† This bit is cleared only by the assertion of GRST when PME is enabled. If PME is not enabled, then this bit is cleared by the assertion of PRST
or GRST.
6–2
6.2 Socket Mask Register
This register allows software to control the CardBus card events which generate a status change interrupt. The state
of these mask bits does not prevent the corresponding bits from reacting in the socket event register (offset 00h, see
Section 6.1). See Table 6–3 for a complete description of the register contents.
Bit
31
30
29
28
27
26
25
Name
24
23
22
21
20
19
18
17
16
Socket mask
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Socket mask
Type
R
R
R
R
R
R
R
R
R
R
R
R
RW
RW
RW
RW
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Socket mask
CardBus Socket Address + 04h
Read-only, Read/Write
0000 0000h
Table 6–3. Socket Mask Register Description
BIT
SIGNAL
TYPE
31–4
RSVD
R
3†
PWRMASK
RW
FUNCTION
These bits return 0s when read.
Power cycle. This bit masks the PWRCYCLE bit in the socket present state register (offset 08h, see
Section 6.3) from causing a status change interrupt.
0 = PWRCYCLE event does not cause a CSC interrupt (default).
1 = PWRCYCLE event causes a CSC interrupt.
Card detect mask. These bits mask the CDETECT1 and CDETECT2 bits in the socket present state
register (offset 08h, see Section 6.3) from causing a CSC interrupt.
2–1†
0†
CDMASK
CSTSMASK
RW
RW
00 = Insertion/removal does not cause a CSC interrupt (default).
01 = Reserved (undefined)
10 = Reserved (undefined)
11 = Insertion/removal causes a CSC interrupt.
CSTSCHG mask. This bit masks the CARDSTS field in the socket present state register (offset 08h, see
Section 6.3) from causing a CSC interrupt.
0 = CARDSTS event does not cause a CSC interrupt (default).
1 = CARDSTS event causes a CSC interrupt.
† This bit is cleared only by the assertion of GRST when PME is enabled. If PME is not enabled, then this bit is cleared by the assertion of PRST
or GRST.
6–3
6.3 Socket Present State Register
This register reports information about the socket interface. Writes to the socket force event register (offset 0Ch, see
Section 6.4), as well as general socket interface status, are reflected here. Information about PC Card VCC support
and card type is only updated at each insertion. Also note that the PCI7410 device uses the CCD1 and CCD2 signals
during card identification, and changes on these signals during this operation are not reflected in this register.
Bit
31
30
29
28
27
26
25
Type
R
R
R
R
R
R
R
R
Default
0
0
1
1
0
0
0
Bit
15
14
13
12
11
10
9
Name
24
23
22
21
20
19
18
17
16
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
0
8
7
6
5
4
3
2
1
0
Socket present state
Name
Socket present state
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
X
0
0
0
X
X
X
Register:
Offset:
Type:
Default:
Socket present state
CardBus Socket Address + 08h
Read-only
3000 00XXh
Table 6–4. Socket Present State Register Description
BIT
SIGNAL
TYPE
FUNCTION
31
YVSOCKET
R
YV socket. This bit indicates whether or not the socket can supply VCC = Y.Y V to PC Cards. The
PCI7410 device does not support Y.Y-V VCC; therefore, this bit is always reset unless overridden by
the socket force event register (offset 0Ch, see Section 6.4). This bit defaults to 0.
30
XVSOCKET
R
XV socket. This bit indicates whether or not the socket can supply VCC = X.X V to PC Cards. The
PCI7410 device does not support X.X-V VCC; therefore, this bit is always reset unless overridden by
the socket force event register (offset 0Ch, see Section 6.4). This bit defaults to 0.
29
3VSOCKET
R
3-V socket. This bit indicates whether or not the socket can supply VCC = 3.3 Vdc to PC Cards. The
PCI7410 device does support 3.3-V VCC; therefore, this bit is always set unless overridden by the
socket force event register (offset 0Ch, see Section 6.4).
28
5VSOCKET
R
5-V socket. This bit indicates whether or not the socket can supply VCC = 5 Vdc to PC Cards. The
PCI7410 device does support 5-V VCC; therefore, this bit is always set unless overridden by bit 6 of
the device control register (PCI offset 92h, see Section 4.40).
27 †
ZVSUPPORT
R
Zoomed video support. This bit indicates whether or not the socket has support for zoomed video.
0 = ZV support disabled
1 = ZV support enabled
26–14
RSVD
R
These bits return 0s when read.
13 †
YVCARD
R
YV card. This bit indicates whether or not the PC Card inserted in the socket supports VCC = Y.Y Vdc.
This bit can be set by writing a 1 to the corresponding bit in the socket force event register (offset 0Ch,
see Section 6.4).
12 †
XVCARD
R
XV card. This bit indicates whether or not the PC Card inserted in the socket supports VCC = X.X Vdc.
This bit can be set by writing a 1 to the corresponding bit in the socket force event register (offset 0Ch,
see Section 6.4).
11 †
3VCARD
R
3-V card. This bit indicates whether or not the PC Card inserted in the socket supports VCC = 3.3 Vdc.
This bit can be set by writing a 1 to the corresponding bit in the socket force event register (offset 0Ch,
see Section 6.4).
10 †
5VCARD
R
5-V card. This bit indicates whether or not the PC Card inserted in the socket supports VCC = 5 Vdc.
This bit can be set by writing a 1 to the corresponding bit in the socket force event register (offset 0Ch,
see Section 6.4).
† One or more bits in the register are PME context bits and can be cleared only by the assertion of GRST when PME is enabled. If PME is not
enabled, then these bits are cleared by the assertion of PRST or GRST.
6–4
Table 6–4. Socket Present State Register Description (Continued)
BIT
SIGNAL
TYPE
9†
BADVCCREQ
R
8†
DATALOST
R
FUNCTION
Bad VCC request. This bit indicates that the host software has requested that the socket be powered at
an invalid voltage.
0 = Normal operation (default)
1 = Invalid VCC request by host software
Data lost. This bit indicates that a PC Card removal event may have caused lost data because the cycle
did not terminate properly or because write data still resides in the PCI7410 device.
0 = Normal operation (default)
1 = Potential data loss due to card removal
7†
NOTACARD
R
Not a card. This bit indicates that an unrecognizable PC Card has been inserted in the socket. This bit is
not updated until a valid PC Card is inserted into the socket.
0 = Normal operation (default)
1 = Unrecognizable PC Card detected
6
IREQCINT
R
READY(IREQ)//CINT. This bit indicates the current status of the READY(IREQ)//CINT signal at the PC
Card interface.
0 = READY(IREQ)//CINT is low.
1 = READY(IREQ)//CINT is high.
5†
CBCARD
R
CardBus card detected. This bit indicates that a CardBus PC Card is inserted in the socket. This bit is not
updated until another card interrogation sequence occurs (card insertion).
4†
16BITCARD
R
16-bit card detected. This bit indicates that a 16-bit PC Card is inserted in the socket. This bit is not
updated until another card interrogation sequence occurs (card insertion).
3†
PWRCYCLE
R
Power cycle. This bit indicates the status of each card powering request. This bit is encoded as:
0 = Socket is powered down (default).
1 = Socket is powered up.
2†
CDETECT2
R
CCD2. This bit reflects the current status of the CCD2 signal at the PC Card interface. Changes to this
signal during card interrogation are not reflected here.
0 = CCD2 is low (PC Card may be present)
1 = CCD2 is high (PC Card not present)
1†
CDETECT1
R
CCD1. This bit reflects the current status of the CCD1 signal at the PC Card interface. Changes to this
signal during card interrogation are not reflected here.
0 = CCD1 is low (PC Card may be present).
1 = CCD1 is high (PC Card not present).
CSTSCHG. This bit reflects the current status of the CSTSCHG signal at the PC Card interface.
0 = CSTSCHG is low.
1 = CSTSCHG is high.
† One or more bits in the register are PME context bits and can be cleared only by the assertion of GRST when PME is enabled. If PME is not
enabled, then these bits are cleared by the assertion of PRST or GRST.
0
CARDSTS
R
6.4 Socket Force Event Register
This register is used to force changes to the socket event register (offset 00h, see Section 6.1) and the socket present
state register (offset 08h, see Section 6.3). The CVSTEST bit (bit 14) in this register must be written when forcing
changes that require card interrogation. See Table 6–5 for a complete description of the register contents.
Bit
31
30
29
28
27
26
25
Name
Type
24
23
22
21
20
19
18
17
16
Socket force event
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Socket force event
Type
R
W
W
W
W
W
W
W
W
R
W
W
W
W
W
W
Default
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Register:
Offset:
Type:
Default:
Socket force event
CardBus Socket Address + 0Ch
Read-only, Write-only
0000 XXXXh
6–5
Table 6–5. Socket Force Event Register Description
BIT
31–28
27
SIGNAL
TYPE
RSVD
R
FZVSUPPORT
(function 0)
RSVD
(function 1)
W
FUNCTION
Reserved. These bits return 0s when read.
Force zoomed video support. Writes to this bit cause the ZVSUPPORT bit in the socket present state
register to be written.
Reserved. This bit returns 0 when read.
26–15
RSVD
R
These bits return 0s when read.
14
CVSTEST
W
Card VS test. When this bit is set, the PCI7410 device reinterrogates the PC Card, updates the socket
present state register (offset 08h, see Section 6.3), and re-enables the socket power control.
13
FYVCARD
W
Force YV card. Writes to this bit cause the YVCARD bit in the socket present state register (offset 08h,
see Section 6.3) to be written. When set, this bit disables the socket power control.
12
FXVCARD
W
Force XV card. Writes to this bit cause the XVCARD bit in the socket present state register (offset 08h,
see Section 6.3) to be written. When set, this bit disables the socket power control.
11
F3VCARD
W
Force 3-V card. Writes to this bit cause the 3VCARD bit in the socket present state register (offset 08h,
see Section 6.3) to be written. When set, this bit disables the socket power control.
10
F5VCARD
W
Force 5-V card. Writes to this bit cause the 5VCARD bit in the socket present state register (offset 08h,
see Section 6.3) to be written. When set, this bit disables the socket power control.
9
FBADVCCREQ
W
Force BadVccReq. Changes to the BADVCCREQ bit in the socket present state register (offset 08h,
see Section 6.3) can be made by writing this bit.
8
FDATALOST
W
Force data lost. Writes to this bit cause the DATALOST bit in the socket present state register (offset
08h, see Section 6.3) to be written.
7
FNOTACARD
W
Force not a card. Writes to this bit cause the NOTACARD bit in the socket present state register (offset
08h, see Section 6.3) to be written.
6
RSVD
R
This bit returns 0 when read.
5
FCBCARD
W
Force CardBus card. Writes to this bit cause the CBCARD bit in the socket present state register (offset
08h, see Section 6.3) to be written.
4
F16BITCARD
W
Force 16-bit card. Writes to this bit cause the 16BITCARD bit in the socket present state register (offset
08h, see Section 6.3) to be written.
3
FPWRCYCLE
W
Force power cycle. Writes to this bit cause the PWREVENT bit in the socket event register (offset 00h,
see Section 6.1) to be written, and the PWRCYCLE bit in the socket present state register (offset 08h,
see Section 6.3) is unaffected.
2
FCDETECT2
W
Force CCD2. Writes to this bit cause the CD2EVENT bit in the socket event register (offset 00h, see
Section 6.1) to be written, and the CDETECT2 bit in the socket present state register (offset 08h, see
Section 6.3) is unaffected.
1
FCDETECT1
W
Force CCD1. Writes to this bit cause the CD1EVENT bit in the socket event register (offset 00h, see
Section 6.1) to be written, and the CDETECT1 bit in the socket present state register (offset 08h, see
Section 6.3) is unaffected.
0
FCARDSTS
W
Force CSTSCHG. Writes to this bit cause the CSTSEVENT bit in the socket event register (offset 00h,
see Section 6.1) to be written. The CARDSTS bit in the socket present state register (offset 08h, see
Section 6.3) is unaffected.
6–6
6.5 Socket Control Register
This register provides control of the voltages applied to the socket VPP and VCC. The PCI7410 device ensures that
the socket is powered up only at acceptable voltages when a CardBus card is inserted. See Table 6–6 for a complete
description of the register contents.
Bit
31
30
29
28
27
26
25
Name
24
23
22
21
20
19
18
17
16
Socket control
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Type
R
R
R
R
R
R
RW
R
RW
RW
RW
RW
R
RW
RW
RW
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Name
Socket control
Register:
Offset:
Type:
Default:
Socket control
CardBus Socket Address + 10h
Read-only, Read/Write
0000 0000h
Table 6–6. Socket Control Register Description
BIT
SIGNAL
TYPE
31–12
RSVD
R
These bits return 0s when read.
FUNCTION
11
ZV_ACTIVITY
R
This bit returns 0 when the ZVEN bits (bit 0) for both sockets are 0 (disabled). If either ZVEN bit is
set to 1, the ZV_ACTIVITY bit returns 1.
10
STANDARDZVREG
R
Standardized zoomed video register model supported. Because the PCI7410 device supports this
register model, this bit is hardwired to 1.
9
ZVEN
RW
8
RSVD
R
Zoomed video enable. This bit enables zoomed video for the socket.
These bits return 0s when read.
This bit controls how the CardBus clock run state machine decides when to stop the CardBus clock
to the CardBus card:
7
STOPCLK
RW
0 = The CardBus CLKRUN protocol can only attempt to stop/slow the CaredBus clock if the
sockethas been idle for 8 clocks and the PCI CLKRUN protocol is preparing to stop/slow the
PCI bus clock.
1 = The CardBus CLKRUN protocol can only attempt to stop/slow the CaredBus clock if the
socket has been idle for 8 clocks, regardless of the state of the PCI CLKRUN signal.
6–4 †
VCCCTRL
RW
3
RSVD
R
2–0 †
VPPCTRL
RW
VCC control. These bits are used to request card VCC changes.
000 = Request power off (default)
100 = Request VCC = X.X V
001 = Reserved
101 = Request VCC = Y.Y V
010 = Request VCC = 5 V
110 = Reserved
011 = Request VCC = 3.3 V
111 = Reserved
This bit returns 0 when read.
VPP control. These bits are used to request card VPP changes.
000 = Request power off (default)
100 = Request VPP = X.X V
001 = Request VPP = 12 V
101 = Request VPP = Y.Y V
010 = Request VPP = 5 V
110 = Reserved
011 = Request VPP = 3.3 V
111 = Reserved
† One or more bits in the register are PME context bits and can be cleared only by the assertion of GRST when PME is enabled. If PME is not
enabled, then this bit is cleared by the assertion of PRST or GRST.
6–7
6.6 Socket Power Management Register
This register provides power management control over the socket through a mechanism for slowing or stopping the
clock on the card interface when the card is idle. See Table 6–7 for a complete description of the register contents.
Bit
31
30
29
28
27
26
Name
25
24
23
22
21
20
19
18
17
16
Socket power management
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
RW
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Socket power management
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
RW
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Socket power management
CardBus Socket Address + 20h
Read-only, Read/Write
0000 0000h
Table 6–7. Socket Power Management Register Description
BIT
SIGNAL
TYPE
31–26
RSVD
R
25 ‡
SKTACCES
R
24 ‡
SKTMODE
R
23–17
RSVD
R
16
CLKCTRLEN
RW
15–1
RSVD
R
0
CLKCTRL
RW
FUNCTION
Reserved. These bits return 0s when read.
Socket access status. This bit provides information on whether a socket access has occurred. This bit is
cleared by a read access.
0 = No PC Card access has occurred (default).
1 = PC Card has been accessed.
Socket mode status. This bit provides clock mode information.
0 = Normal clock operation
1 = Clock frequency has changed.
These bits return 0s when read.
CardBus clock control enable. This bit, when set, enables clock control according to bit 0 (CLKCTRL).
0 = Clock control disabled (default)
1 = Clock control enabled
These bits return 0s when read.
CardBus clock control. This bit determines whether the CardBus CLKRUN protocol attempts to stop or
slow the CardBus clock during idle states. The CLKCTRLEN bit enables this bit.
0 = Allows the CardBus CLKRUN protocol to attempt to stop the CardBus clock (default)
1 = Allows the CardBus CLKRUN protocol to attempt to slow the CardBus clock by a factor of 16
‡ One or more bits in this register are cleared only by the assertion of GRST.
6–8
7 OHCI Controller Programming Model
This section describes the internal PCI configuration registers used to program the PCI7410 1394 open host
controller interface. All registers are detailed in the same format: a brief description for each register is followed by
the register offset and a bit table describing the reset state for each register.
A bit description table, typically included when the register contains bits of more than one type or purpose, indicates
bit field names, a detailed field description, and field access tags which appear in the type column. Table 4–1
describes the field access tags.
The PCI7410 device is a multifunction PCI device. The 1394 OHCI is integrated as PCI function 2. The function 2
configuration header is compliant with the PCI Local Bus Specification as a standard header. Table 7–1 illustrates
the configuration header that includes both the predefined portion of the configuration space and the user-definable
registers.
Table 7–1. Function 2 Configuration Register Map
REGISTER NAME
OFFSET
Device ID
Vendor ID
00h
Status
Command
04h
Class code
BIST
Header type
Latency timer
Revision ID
08h
Cache line size
0Ch
OHCI base address
10h
TI extension base address
14h
CardBus CIS base address
18h
Reserved
1Ch–27h
CardBus CIS pointer ‡
Subsystem ID ‡
28h
Subsystem vendor ID ‡
Reserved
Reserved
30h
PCI power
management
capabilities pointer
34h
Interrupt line
3Ch
Reserved
Maximum latency ‡
Minimum grant ‡
Interrupt pin
38h
PCI OHCI control
Power management capabilities
PM data
Next item pointer
PMCSR_BSE
2Ch
40h
Capability ID
Power management control and status ‡
44h
48h
Reserved
4Ch–EBh
PCI PHY control ‡
ECh
PCI miscellaneous configuration ‡
F0h
Link enhancement control ‡
F4h
Subsystem access
F8h
Reserved
FCh
‡ One or more bits in this register are cleared only by the assertion of GRST.
7–1
7.1 Vendor ID Register
The vendor ID register contains a value allocated by the PCI SIG and identifies the manufacturer of the PCI device.
The vendor ID assigned to Texas Instruments is 104Ch.
Bit
15
14
13
12
11
10
9
Name
8
7
6
5
4
3
2
1
0
Vendor ID
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
1
0
0
0
0
0
1
0
0
1
1
0
0
Register:
Offset:
Type:
Default:
Vendor ID
00h
Read-only
104Ch
7.2 Device ID Register
The device ID register contains a value assigned to the PCI7410 device by Texas Instruments. The device
identification for the PCI7410 device is 802Bh.
Bit
15
14
13
12
11
10
9
Type
R
R
R
R
R
R
R
R
Default
1
0
0
0
0
0
0
0
Name
7
6
5
4
3
2
1
0
R
R
R
R
R
R
R
R
0
0
1
0
1
0
1
1
Device ID
Register:
Offset:
Type:
Default:
7–2
8
Device ID
02h
Read-only
802Bh
7.3 Command Register
The command register provides control over the PCI7410 interface to the PCI bus. All bit functions adhere to the
definitions in the PCI Local Bus Specification, as seen in the following bit descriptions. See Table 7–2 for a complete
description of the register contents.
Bit
15
14
13
12
11
10
9
Name
8
7
6
5
4
3
2
1
0
Command
Type
R
R
R
R
R
RW
R
RW
R
RW
R
RW
R
RW
RW
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Command
04h
Read/Write, Read-only
0000h
Table 7–2. Command Register Description
BIT
FIELD NAME
TYPE
15–11
RSVD
R
10
INT_DISABLE
RW
DESCRIPTION
Reserved. Bits 15–10 return 0s when read.
INTx disable. When set to 1, this bit disables the function from asserting interrupts on the INTx signals.
0 = INTx assertion is enabled (default)
1 = INTx assertion is disabled
This bit is disabled (read-only 0) if bit 11 (PCI2_3_EN) in the PCI miscellaneous configuration
register (see Section 7.23) is 0.
9
FBB_ENB
R
Fast back-to-back enable. The PCI7410 device does not generate fast back-to-back transactions;
therefore, bit 9 returns 0 when read.
8
SERR_ENB
RW
SERR enable. When bit 8 is set to 1, the PCI7410 SERR driver is enabled. SERR can be asserted after
detecting an address parity error on the PCI bus.
7
RSVD
R
6
PERR_ENB
RW
Reserved. Bit 7 returns 0 when read.
Parity error enable. When bit 6 is set to 1, the PCI7410 device is enabled to drive PERR response to
parity errors through the PERR signal.
5
VGA_ENB
R
VGA palette snoop enable. The PCI7410 device does not feature VGA palette snooping; therefore,
bit 5 returns 0 when read.
4
MWI_ENB
RW
Memory write and invalidate enable. When bit 4 is set to 1, the PCI7410 device is enabled to generate
MWI PCI bus commands. If this bit is cleared, then the PCI7410 device generates memory write
commands instead.
3
SPECIAL
R
Special cycle enable. The PCI7410 function does not respond to special cycle transactions; therefore,
bit 3 returns 0 when read.
2
MASTER_ENB
RW
Bus master enable. When bit 2 is set to 1, the PCI7410 device is enabled to initiate cycles on the PCI
bus.
1
MEMORY_ENB
RW
Memory response enable. Setting bit 1 to 1 enables the PCI7410 device to respond to memory cycles
on the PCI bus. This bit must be set to access OHCI registers.
0
IO_ENB
R
I/O space enable. The PCI7410 device does not implement any I/O-mapped functionality; therefore,
bit 0 returns 0 when read.
7–3
7.4 Status Register
The status register provides status over the PCI7410 interface to the PCI bus. All bit functions adhere to the definitions
in the PCI Local Bus Specification, as seen in the following bit descriptions. See Table 7–3 for a complete description
of the register contents.
Bit
15
14
13
12
11
10
9
8
Name
Type
Default
7
6
5
4
3
2
1
0
Status
RCU
RCU
RCU
RCU
RCU
R
R
RCU
R
R
R
R
RU
R
R
R
0
0
0
0
0
0
1
0
0
0
0
1
0
0
0
0
Register:
Offset:
Type:
Default:
Status
06h
Read/Clear/Update, Read-only
0210h
Table 7–3. Status Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
15
PAR_ERR
RCU
Detected parity error. Bit 15 is set to 1 when either an address parity or data parity error is detected.
14
SYS_ERR
RCU
Signaled system error. Bit 14 is set to 1 when SERR is enabled and the PCI7410 device has signaled
a system error to the host.
13
MABORT
RCU
Received master abort. Bit 13 is set to 1 when a cycle initiated by the PCI7410 device on the PCI bus
has been terminated by a master abort.
12
TABORT_REC
RCU
Received target abort. Bit 12 is set to 1 when a cycle initiated by the PCI7410 device on the PCI bus
was terminated by a target abort.
11
TABORT_SIG
RCU
Signaled target abort. Bit 11 is set to 1 by the PCI7410 device when it terminates a transaction on the
PCI bus with a target abort.
10–9
PCI_SPEED
R
DEVSEL timing. Bits 10 and 9 encode the timing of DEVSEL and are hardwired to 01b, indicating that
the PCI7410 device asserts this signal at a medium speed on nonconfiguration cycle accesses.
8
DATAPAR
RCU
Data parity error detected. Bit 8 is set to 1 when the following conditions have been met:
a. PERR was asserted by any PCI device including the PCI7410 device.
b. The PCI7410 device was the bus master during the data parity error.
c. Bit 6 (PERR_EN) in the command register at offset 04h in the PCI configuration space
(see Section 7.3) is set to 1.
7–4
7
FBB_CAP
R
Fast back-to-back capable. The PCI7410 device cannot accept fast back-to-back transactions;
therefore, bit 7 is hardwired to 0.
6
UDF
R
User-definable features (UDF) supported. The PCI7410 device does not support the UDF; therefore,
bit 6 is hardwired to 0.
5
66MHZ
R
66-MHz capable. The PCI7410 device operates at a maximum PCLK frequency of 33 MHz; therefore,
bit 5 is hardwired to 0.
4
CAPLIST
R
Capabilities list. Bit 4 returns 1 when read, indicating that capabilities additional to standard PCI are
implemented. The linked list of PCI power-management capabilities is implemented in this function.
3
INT_STATUS
RU
Interrupt status. This bit reflects the interrupt status of the function. Only when bit 10 (INT_DISABLE)
in the command register (see Section 7.3) is a 0 and this bit is 1, will the function’s INTx signal be
asserted. Setting the INT_DISABLE bit to 1 has no effect on the state of this bit. This bit is disabled
(read-only 0) if bit 11 (PCI2_3_EN) in the PCI miscellaneous configuration register (see Section 7.23)
is 0.
2–0
RSVD
R
Reserved. Bits 3–0 return 0s when read.
7.5 Class Code and Revision ID Register
The class code and revision ID register categorizes the PCI7410 device as a serial bus controller (0Ch), controlling
an IEEE 1394 bus (00h), with an OHCI programming model (10h). Furthermore, the TI chip revision is indicated in
the least significant byte. See Table 7–4 for a complete description of the register contents.
Bit
31
30
29
28
27
26
R
R
R
R
R
R
R
R
R
Name
Type
25
24
23
22
21
20
19
18
17
16
R
R
R
R
R
R
R
Class code and revision ID
Default
0
0
0
0
1
1
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Class code and revision ID
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Class code and revision ID
08h
Read-only
0C00 1000h
Table 7–4. Class Code and Revision ID Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31–24
BASECLASS
R
Base class. This field returns 0Ch when read, which broadly classifies the function as a serial bus
controller.
23–16
SUBCLASS
R
Subclass. This field returns 00h when read, which specifically classifies the function as controlling an
IEEE 1394 serial bus.
15–8
PGMIF
R
Programming interface. This field returns 10h when read, which indicates that the programming model
is compliant with the 1394 Open Host Controller Interface Specification.
7–0
CHIPREV
R
Silicon revision. This field returns 00h when read, which indicates the silicon revision of the PCI7410
device.
7.6 Latency Timer and Class Cache Line Size Register
The latency timer and class cache line size register is programmed by host BIOS to indicate system cache line size
and the latency timer associated with the PCI7410 device. See Table 7–5 for a complete description of the register
contents.
Bit
15
14
13
12
11
10
Name
Type
Default
9
8
7
6
5
4
3
2
1
0
Latency timer and class cache line size
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Latency timer and class cache line size
0Ch
Read/Write
0000h
Table 7–5. Latency Timer and Class Cache Line Size Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
15–8
LATENCY_TIMER
RW
PCI latency timer. The value in this register specifies the latency timer for the PCI7410 device, in units
of PCI clock cycles. When the PCI7410 device is a PCI bus initiator and asserts FRAME, the latency
timer begins counting from zero. If the latency timer expires before the PCI7410 transaction has
terminated, then the PCI7410 device terminates the transaction when its GNT is deasserted.
7–0
CACHELINE_SZ
RW
Cache line size. This value is used by the PCI7410 device during memory write and invalidate,
memory-read line, and memory-read multiple transactions.
7–5
7.7 Header Type and BIST Register
The header type and built-in self-test (BIST) register indicates the PCI7410 PCI header type and no built-in self-test.
See Table 7–6 for a complete description of the register contents.
Bit
15
14
13
12
11
10
9
Name
8
7
6
5
4
3
2
1
0
Header type and BIST
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Header type and BIST
0Eh
Read-only
0000h
Table 7–6. Header Type and BIST Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
15–8
BIST
R
Built-in self-test. The PCI7410 device does not include a BIST; therefore, this field returns 00h when
read.
7–0
HEADER_TYPE
R
PCI header type. The PCI7410 device includes the standard PCI header, which is communicated by
returning 00h when this field is read.
7.8 OHCI Base Address Register
The OHCI base address register is programmed with a base address referencing the memory-mapped OHCI control.
When BIOS writes all 1s to this register, the value read back is FFFF F800h, indicating that at least 2K bytes of
memory address space are required for the OHCI registers. See Table 7–7 for a complete description of the register
contents.
Bit
31
30
29
28
27
26
25
RW
RW
RW
RW
RW
RW
RW
RW
Default
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
Name
Type
Default
23
22
21
20
19
18
17
16
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
7
6
5
4
3
2
1
0
OHCI base address
Name
Type
24
OHCI base address
RW
RW
RW
RW
RW
R
R
R
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
OHCI base address
10h
Read/Write, Read-only
0000 0000h
Table 7–7. OHCI Base Address Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31–11
OHCIREG_PTR
RW
OHCI register pointer. This field specifies the upper 21 bits of the 32-bit OHCI base address register.
10–4
OHCI_SZ
R
OHCI register size. This field returns 0s when read, indicating that the OHCI registers require a
2K-byte region of memory.
3
OHCI_PF
R
OHCI register prefetch. Bit 3 returns 0 when read, indicating that the OHCI registers are
nonprefetchable.
2–1
OHCI_MEMTYPE
R
OHCI memory type. This field returns 0s when read, indicating that the OHCI base address register
is 32 bits wide and mapping can be done anywhere in the 32-bit memory space.
0
OHCI_MEM
R
OHCI memory indicator. Bit 0 returns 0 when read, indicating that the OHCI registers are mapped
into system memory space.
7–6
7.9 TI Extension Base Address Register
The TI extension base address register is programmed with a base address referencing the memory-mapped TI
extension registers. When BIOS writes all 1s to this register, the value read back is FFFF C000h, indicating that at
least 16K bytes of memory address space are required for the TI registers. See Table 7–8 for a complete description
of the register contents.
Bit
31
30
29
28
27
26
Name
Type
25
24
23
22
21
20
19
18
17
16
TI extension base address
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
TI extension base address
RW
RW
R
R
R
R
R
R
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
TI extension base address
14h
Read/Write, Read-only
0000 0000h
Table 7–8. TI Base Address Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31–14
TIREG_PTR
RW
13–4
TI_SZ
R
TI register size. This field returns 0s when read, indicating that the TI registers require a 16K-byte
region of memory.
3
TI_PF
R
TI register prefetch. Bit 3 returns 0 when read, indicating that the TI registers are nonprefetchable.
2–1
TI_MEMTYPE
R
TI memory type. This field returns 0s when read, indicating that the TI base address register is 32 bits
wide and mapping can be done anywhere in the 32-bit memory space.
0
TI_MEM
R
TI memory indicator. Bit 0 returns 0 when read, indicating that the TI registers are mapped into system
memory space.
TI register pointer. This field specifies the upper 18 bits of the 32-bit TI base address register.
7–7
7.10 CardBus CIS Base Address Register
The internal CARDBUS input to the TSB43AB22 core is tied high such that this register returns 0s when read. See
Table 7–9 for a complete description of the register contents.
Bit
31
30
29
28
27
26
25
RW
RW
RW
RW
RW
RW
RW
RW
RW
Default
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
Name
Type
Default
23
22
21
20
19
18
17
16
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
6
5
4
3
2
1
0
CardBus CIS base address
Name
Type
24
CardBus CIS base address
RW
RW
RW
RW
RW
R
R
R
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
CardBus CIS base address
18h
Read/Write, Read-only
0000 0000h
Table 7–9. CardBus CIS Base Address Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31–11
CIS_BASE
RW
CIS base address. This field specifies the upper 21 bits of the 32-bit CIS base address. If CARDBUS
is sampled high on a GRST, then this field is read-only, returning 0s when read.
10–4
CIS_SZ
R
CIS address space size. This field returns 0s when read, indicating that the CIS space requires a
2K-byte region of memory.
3
CIS_PF
R
CIS prefetch. Bit 3 returns 0 when read, indicating that the CIS is nonprefetchable. Furthermore, the
CIS is a byte-accessible address space, and either a doubleword or 16-bit word access yields
indeterminate results.
2–1
CIS_MEMTYPE
R
CIS memory type. This field returns 0s when read, indicating that the CardBus CIS base address
register is 32 bits wide and mapping can be done anywhere in the 32-bit memory space.
0
CIS_MEM
R
CIS memory indicator. Bit 0 returns 0 when read, indicating that the CIS is mapped into system
memory space.
7.11 CardBus CIS Pointer Register
The internal CARDBUS input to the TSB43AB22 core is tied high such that this register returns 0s when read.
Bit
31
30
29
28
27
26
25
Name
24
23
22
21
20
19
18
17
16
CardBus CIS pointer
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
CardBus CIS pointer
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
7–8
CardBus CIS pointer
28h
Read-only
0000 0000h
7.12 Subsystem Identification Register
The subsystem identification register is used for system and option card identification purposes. This register can
be initialized from the serial EEPROM or programmed via the subsystem access register at offset F8h in the PCI
configuration space (see Section 7.25). See Table 7–10 for a complete description of the register contents.
Bit
31
30
29
28
27
26
Name
Type
25
24
23
22
21
20
19
18
17
16
Subsystem identification
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Subsystem identification
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Subsystem identification
2Ch
Read/Update
0000 0000h
Table 7–10. Subsystem Identification Register Description
BIT
FIELD NAME
TYPE
31–16 ‡
OHCI_SSID
RU
15–0 ‡
OHCI_SSVID
RU
DESCRIPTION
Subsystem device ID. This field indicates the subsystem device ID.
Subsystem vendor ID. This field indicates the subsystem vendor ID.
‡ One or more bits in this register are cleared only by the assertion of GRST.
7.13 Power Management Capabilities Pointer Register
The power management capabilities pointer register provides a pointer into the PCI configuration header where the
power-management register block resides. The PCI7410 configuration header doublewords at offsets 44h and 48h
provide the power-management registers. This register is read-only and returns 44h when read.
Bit
7
6
5
Name
4
3
2
1
0
Power management capabilities pointer
Type
R
R
R
R
R
R
R
R
Default
0
1
0
0
0
1
0
0
Register:
Offset:
Type:
Default:
Power management capabilities pointer
34h
Read-only
44h
7–9
7.14 Interrupt Line Register
The interrupt line register communicates interrupt line routing information. See Table 7–11 for a complete description
of the register contents.
Bit
7
6
5
4
Name
Type
Default
3
2
1
0
Interrupt line
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Interrupt line
3Ch
Read/Write
00h
Table 7–11. Interrupt Line Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
7–0
INTR_LINE
RW
Interrupt line. This field is programmed by the system and indicates to software which interrupt line the
PCI7410 PCI_INTA is connected to.
7.15 Interrupt Pin Register
The value read from this register is function dependent and depends on the values of bits 28, the tie-all bit (TIEALL),
and 29, the interrupt tie bit (INTRTIE), in the system control register (PCI offset 80h, see Section 4.30). The INTRTIE
bit is compatible with previous TI CardBus controllers, and when set to 1, ties INTB to INTA internally. The TIEALL
bit ties INTA, INTB, and INTC together internally. The internal interrupt connections set by INTRTIE and TIEALL are
communicated to host software through this standard register interface. This read-only register is described for all
PCI7410 functions in Table 7–12.
Bit
7
6
5
4
3
2
1
0
Type
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
1
0
Name
Interrupt pin
Register:
Offset:
Type:
Default:
Interrupt pin
3Dh
Read-only
02h
Table 7–12. PCI Interrupt Pin Register—Read-Only INTPIN Per Function
INTRTIE BIT
(BIT 29, OFFSET 80h)
TIEALL BIT
(BIT 28, OFFSET 80h)
INTPIN
FUNCTION 0
(CARDBUS)
INTPIN
FUNCTION 1
(DEDICATED SOCKET)
INTPIN
FUNCTION 2
(1394 OHCI)
0
0
01h (INTA)
02h (INTB)
03h (INTC)
1
0
01h (INTA)
01h (INTA)
03h (INTC)
X
1
01h (INTA)
01h (INTA)
01h (INTA)
NOTE: When configuring the PCI7410 functions to share PCI interrupts, multifunction terminal MFUNC3 must be configured as IRQSER prior
to setting the INTRTIE bit.
7–10
7.16 Minimum Grant and Maximum Latency Register
The minimum grant and maximum latency register communicates to the system the desired setting of bits 15–8 in
the latency timer and class cache line size register at offset 0Ch in the PCI configuration space (see Section 7.6).
If a serial EEPROM is detected, then the contents of this register are loaded through the serial EEPROM interface
after a GRST. If no serial EEPROM is detected, then this register returns a default value that corresponds to the
MAX_LAT = 4, MIN_GNT = 2. See Table 7–13 for a complete description of the register contents.
Bit
15
14
13
12
11
10
Name
Type
Default
9
8
7
6
5
4
3
2
1
0
Minimum grant and maximum latency
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
0
0
0
0
0
1
0
0
0
0
0
0
0
0
1
0
Register:
Offset:
Type:
Default:
Minimum grant and maximum latency
3Eh
Read/Update
0402h
Table 7–13. Minimum Grant and Maximum Latency Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
15–8 ‡
MAX_LAT
RU
Maximum latency. The contents of this field may be used by host BIOS to assign an arbitration priority level
to the PCI7410 device. The default for this register indicates that the PCI7410 device may need to access
the PCI bus as often as every 0.25 µs; thus, an extremely high priority level is requested. The contents of
this field may also be loaded through the serial EEPROM.
7–0 ‡
MIN_GNT
RU
Minimum grant. The contents of this field may be used by host BIOS to assign a latency timer register value
to the PCI7410 device. The default for this register indicates that the PCI7410 device may need to sustain
burst transfers for nearly 64 µs and thus request a large value be programmed in bits 15–8 of the PCI7410
latency timer and class cache line size register at offset 0Ch in the PCI configuration space (see
Section 7.6).
‡ One or more bits in this register are cleared only by the assertion of GRST.
7.17 OHCI Control Register
The PCI OHCI control register is defined by the 1394 Open Host Controller Interface Specification and provides a
bit for big endian PCI support. See Table 7–14 for a complete description of the register contents.
Bit
31
30
29
28
27
26
25
R
R
R
R
R
R
R
R
Name
Type
24
23
22
21
20
19
18
17
16
R
R
R
R
R
R
R
R
OHCI control
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
RW
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Name
OHCI control
Register:
Offset:
Type:
Default:
OHCI control
40h
Read/Write, Read-only
0000 0000h
Table 7–14. OHCI Control Register Description
BIT
FIELD NAME
TYPE
31–1
RSVD
R
0
GLOBAL_SWAP
RW
DESCRIPTION
Reserved. Bits 31–1 return 0s when read.
When bit 0 is set to 1, all quadlets read from and written to the PCI interface are byte-swapped (big
endian).
7–11
7.18 Capability ID and Next Item Pointer Registers
The capability ID and next item pointer register identifies the linked-list capability item and provides a pointer to the
next capability item. See Table 7–15 for a complete description of the register contents.
Bit
15
14
13
12
11
10
Name
9
8
7
6
5
4
3
2
1
0
Capability ID and next item pointer
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
Register:
Offset:
Type:
Default:
Capability ID and next item pointer
44h
Read-only
0001h
Table 7–15. Capability ID and Next Item Pointer Registers Description
7–12
BIT
FIELD NAME
TYPE
DESCRIPTION
15–8
NEXT_ITEM
R
Next item pointer. The PCI7410 device supports only one additional capability that is communicated
to the system through the extended capabilities list; therefore, this field returns 00h when read.
7–0
CAPABILITY_ID
R
Capability identification. This field returns 01h when read, which is the unique ID assigned by the PCI
SIG for PCI power-management capability.
7.19 Power Management Capabilities Register
The power management capabilities register indicates the capabilities of the PCI7410 device related to PCI power
management. See Table 7–16 for a complete description of the register contents.
Bit
15
14
13
12
11
10
Name
Type
Default
9
8
7
6
5
4
3
2
1
0
Power management capabilities
RU
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
0
1
1
1
1
1
1
0
0
0
0
0
0
0
1
0
Register:
Offset:
Type:
Default:
Power management capabilities
46h
Read/Update, Read-only
7E02h
Table 7–16. Power Management Capabilities Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
15
PME_D3COLD
RU
PME support from D3cold. This bit can be set to 1 or cleared to 0 via bit 15 (PME_D3COLD) in the PCI
miscellaneous configuration register at offset F0h in the PCI configuration space (see Section 7.23).
The PCI miscellaneous configuration register is loaded from ROM. When this bit is set to 1, it indicates
that the PCI7410 device is capable of generating a PME wake event from D3cold. This bit state is
dependent upon the PCI7410 VAUX implementation and may be configured by using bit 15
(PME_D3COLD) in the PCI miscellaneous configuration register (see Section 7.23).
14–11
PME_SUPPORT
R
PME support. This 4-bit field indicates the power states from which the PCI7410 device may assert
PME. This field returns a value of 1111b by default, indicating that PME may be asserted from
the D3hot, D2, D1, and D0 power states.
10
D2_SUPPORT
R
D2 support. Bit 10 is hardwired to 1, indicating that the PCI7410 device supports the D2 power state.
9
D1_SUPPORT
R
D1 support. Bit 9 is hardwired to 1, indicating that the PCI7410 device supports the D1 power state.
8–6
AUX_CURRENT
R
Auxiliary current. This 3-bit field reports the 3.3-VAUX auxiliary current requirements. When bit 15
(PME_D3COLD) is cleared, this field returns 000b; otherwise, it returns 001b.
000b = Self-powered
001b = 55 mA (3.3-VAUX maximum current required)
5
DSI
R
Device-specific initialization. This bit returns 0 when read, indicating that the PCI7410 device does not
require special initialization beyond the standard PCI configuration header before a generic class
driver is able to use it.
4
RSVD
R
Reserved. Bit 4 returns 0 when read.
3
PME_CLK
R
PME clock. This bit returns 0 when read, indicating that no host bus clock is required for the PCI7410
device to generate PME.
2–0
PM_VERSION
R
Power-management version. This field returns 010b when read, indicating that the PCI7410 device
is compatible with the registers described in the PCI Bus Power Management Interface Specification
(Revision 1.1).
7–13
7.20 Power Management Control and Status Register
The power management control and status register implements the control and status of the PCI power-management
function. This register is not affected by the internally generated reset caused by the transition from the D3hot to D0
state. See Table 7–17 for a complete description of the register contents.
Bit
15
14
13
12
11
10
RWC
R
R
R
R
R
R
RW
R
0
0
0
0
0
0
0
0
0
Name
Type
Default
9
8
7
6
5
4
3
2
1
0
R
R
R
R
R
RW
RW
0
0
0
0
0
0
0
Power management control and status
Register:
Offset:
Type:
Default:
Power management control and status
48h
Read/Clear, Read/Write, Read-only
0000h
Table 7–17. Power Management Control and Status Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
15 ‡
PME_STS
RWC
Bit 15 is set to 1 when the PCI7410 device normally asserts the PME signal independent of the state
of bit 8 (PME_ENB). This bit is cleared by a writeback of 1, which also clears the PME signal driven
by the PCI7410 device. Writing a 0 to this bit has no effect.
14–13
DATA_SCALE
R
This field returns 0s, because the data register is not implemented.
12–9
DATA_SELECT
R
This field returns 0s, because the data register is not implemented.
8‡
PME_ENB
RW
7–2
RSVD
R
1–0 ‡
PWR_STATE
RW
When bit 8 is set to 1, PME assertion is enabled. When bit 8 is cleared, PME assertion is disabled. This
bit defaults to 0 if the function does not support PME generation from D3cold. If the function supports
PME from D3cold, then this bit is sticky and must be explicitly cleared by the operating system each
time it is initially loaded.
Reserved. Bits 7–2 return 0s when read.
Power state. This 2-bit field sets the PCI7410 device power state and is encoded as follows:
00 = Current power state is D0.
01 = Current power state is D1.
10 = Current power state is D2.
11 = Current power state is D3.
‡ One or more bits in this register are cleared only by the assertion of GRST.
7.21 Power Management Extension Registers
The power management extension register provides extended power-management features not applicable to the
PCI7410 device; thus, it is read-only and returns 0 when read. See Table 7–18 for a complete description of the
register contents.
Bit
15
14
13
12
11
10
Name
9
8
7
6
5
4
3
2
1
0
Power management extension
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Power management extension
4Ah
Read-only
0000h
Table 7–18. Power Management Extension Registers Description
7–14
BIT
FIELD NAME
TYPE
15–0
RSVD
R
DESCRIPTION
Reserved. Bits 15–0 return 0s when read.
7.22 PCI PHY Control Register
The PCI PHY control register provides a method for enabling the PHY CNA output. See Table 7–19 for a complete
description of the register contents.
Bit
31
30
29
28
27
26
25
Name
Type
24
23
22
21
20
19
18
17
16
PCI PHY control
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Type
R
R
R
R
R
R
R
R
RW
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
Name
PCI PHY control
Register:
Offset:
Type:
Default:
PCI PHY control
ECh
Read/Write, Read-only
0000 0008h
Table 7–19. PCI PHY Control Register
BIT
FIELD NAME
TYPE
DESCRIPTION
31–8
RSVD
R
7‡
CNAOUT
RW
When bit 7 is set to 1, the PHY CNA output is routed to terminal 96. When implementing a serial
EEPROM, this bit can be set by programming bit 7 of offset 16h in the EEPROM to 1. See
Table 3–14, EEPROM Loading Map.
6–5
RSVD
R
Reserved. Bits 6–4 return 0s when read. These bits are affected when implementing a serial
EEPROM; thus, bits 6–4 at EEPROM byte offset 16h must be programmed to 0. See Table 3–14,
EEPROM Loading Map.
3‡
RSVD
R
Reserved. Bit 3 defaults to 1 to indicate compliance with IEEE Std 1394a-2000. If a serial
EEPROM is implemented, then bit 3 at EEPROM byte offset 16h must be set to 1. See Table 3–14,
EEPROM Loading Map.
2–0
RSVD
R
Reserved. Bits 2–0 return 0s when read. These bits are affected when implementing a serial
EEPROM; thus, bits 2–0 at EEPROM byte offset 16h must be programmed to 0. See Table 3–14,
EEPROM Loading Map.
4‡
Reserved. Bits 31–8 return 0s when read.
‡ One or more bits in this register are cleared only by the assertion of GRST.
7.23 PCI Miscellaneous Configuration Register
The PCI miscellaneous configuration register provides miscellaneous PCI-related configuration. See Table 7–20 for
a complete description of the register contents.
Bit
31
30
29
28
27
26
R
R
R
R
R
R
R
R
R
Name
Type
25
24
23
22
21
20
19
18
17
16
R
R
R
R
R
R
R
PCI miscellaneous configuration
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RW
R
RW
R
RW
RW
RW
RW
R
R
R
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Name
Type
Default
PCI miscellaneous configuration
Register:
Offset:
Type:
Default:
PCI miscellaneous configuration
F0h
Read/Write, Read-only
0000 0000h
7–15
Table 7–20. PCI Miscellaneous Configuration Register
BIT
FIELD NAME
TYPE
31–16
RSVD
R
15 ‡
PME_D3COLD
RW
14–12
RSVD
R
11 ‡
PCI2_3_EN
RW
DESCRIPTION
Reserved. Bits 31–16 return 0s when read.
PME support from D3cold. This bit programs bit 15 (PME_D3COLD) in the power management
capabilities register at offset 46h in the PCI configuration space (see Section 7.19).
Reserved. Bits 14–12 return 0s when read.
PCI 2.3 Enable. When this bit is set to 1, the 1394 OHCI function conforms to the PCI 2.3
specification. When in the PCI 2.3 mode, the INT_DISABLE and INT_STATUS bits per the PCI 2.3
specification are functional. When this bit is cleared, the function conforms to the PCI 2.2
specification and all PCI 2.3 bits are disabled.
0 = PCI 2.2 mode (default)
1 = PCI 2.3 mode
10 ‡
ignore_mstrIntEna
_for_pme
RW
Ignore IntMask.msterIntEnable bit for PME generation. When set, this bit causes the PME generation
behavior to be changed as described in Section 3.9. When set, this bit also causes bit 26 of the OHCI
vendor ID register at OHCI offset 40h (see Section 8.15) to read 1, otherwise, bit 26 reads 0.
0 = PME behavior generated from unmasked interrupt bits and IntMask.masterIntEnable bit
(default)
1 = PME generation does not depend on the value of IntMask.masterIntEnable
9–8 ‡
MR_ENHANCE
RW
This field selects the read command behavior of the PCI master for read transactions of greater than
two data phases. For read transactions of one or two data phases, a memory read command is used.
The default of this field is 00. This register is loaded by the serial EEPROM word 12, bits 1–0.
00 = Memory read line (default)
01 = Memory read
10 = Memory read multiple
11 = Reserved, behavior reverts to default
7–6
RSVD
R
Reserved. Bits 7–6 return 0s when read.
Reserved. Bit 5 returns 0 when read.
5‡
RSVD
R
4‡
DIS_TGT_ABT
RW
Bit 4 defaults to 0, which provides OHCI-Lynx compatible target abort signaling. When this bit is
set to 1, it enables the no-target-abort mode, in which the PCI7410 device returns indeterminate data
instead of signaling target abort.
The PCI7410 LLC is divided into the PCLK and SCLK domains. If software tries to access registers
in the link that are not active because the SCLK is disabled, then a target abort is issued by the link.
On some systems, this can cause a problem resulting in a fatal system error. Enabling this bit allows
the link to respond to these types of requests by returning FFh.
It is recommended that this bit be set to 1.
3‡
GP2IIC
RW
When bit 3 is set to 1, the GPIO3 and GPIO2 signals are internally routed to the SCL and SDA,
respectively. The GPIO3 and GPIO2 terminals are also placed in the high-impedance state.
2‡
DISABLE_
SCLKGATE
RW
When bit 2 is set to 1, the internal SCLK runs identically with the chip input. This is a test feature only
and must be cleared to 0 (all applications).
1‡
DISABLE_
PCIGATE
RW
When bit 1 is set to 1, the internal PCI clock runs identically with the chip input. This is a test feature
only and must be cleared to 0 (all applications).
0‡
KEEP_PCLK
RW
When bit 0 is set to 1, the PCI clock is always kept running through the CLKRUN protocol. When this
bit is cleared, the PCI clock can be stopped using CLKRUN on MFUNC6.
‡ One or more bits in this register are cleared only by the assertion of GRST.
7–16
7.24 Link Enhancement Control Register
The link enhancement control register implements TI proprietary bits that are initialized by software or by a serial
EEPROM, if present. After these bits are set to 1, their functionality is enabled only if bit 22 (aPhyEnhanceEnable)
in the host controller control register at OHCI offset 50h/54h (see Section 8.16) is set to 1. See Table 7–21 for a
complete description of the register contents.
Bit
31
30
29
28
27
26
Name
Type
25
24
23
22
21
20
19
18
17
16
Link enhancement control
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RW
R
RW
RW
R
RW
R
RW
RW
R
R
R
R
R
RW
R
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
Name
Type
Default
Link enhancement control
Register:
Offset:
Type:
Default:
Link enhancement control
F4h
Read/Write, Read-only
0000 1000h
Table 7–21. Link Enhancement Control Register Description
BIT
FIELD NAME
TYPE
31–16
RSVD
R
15 ‡
dis_at_pipeline
RW
14 ‡
RSVD
R
13–12 ‡
atx_thresh
RW
DESCRIPTION
Reserved. Bits 31–16 return 0s when read.
Disable AT pipelining. When bit 15 is set to 1, out-of-order AT pipelining is disabled.
Reserved.
This field sets the initial AT threshold value, which is used until the AT FIFO is underrun. When the
PCI7410 device retries the packet, it uses a 2K-byte threshold, resulting in a store-and-forward
operation.
00 = Threshold ~ 2K bytes resulting in a store-and-forward operation
01 = Threshold ~ 1.7K bytes (default)
10 = Threshold ~ 1K bytes
11 = Threshold ~ 512 bytes
These bits fine-tune the asynchronous transmit threshold. For most applications the 1.7K-byte
threshold is optimal. Changing this value may increase or decrease the 1394 latency depending on
the average PCI bus latency.
Setting the AT threshold to 1.7K, 1K, or 512 bytes results in data being transmitted at these thresholds
or when an entire packet has been checked into the FIFO. If the packet to be transmitted is larger
than the AT threshold, then the remaining data must be received before the AT FIFO is emptied;
otherwise, an underrun condition occurs, resulting in a packet error at the receiving node. As a result,
the link then commences store-and-forward operation. Wait until it has the complete packet in the
FIFO before retransmitting it on the second attempt to ensure delivery.
An AT threshold of 2K results in store-and-forward operation, which means that asynchronous data
will not be transmitted until an end-of-packet token is received. Restated, setting the AT threshold
to 2K results in only complete packets being transmitted.
Note that this device always uses store-and-forward when the asynchronous transmit retries register
at OHCI offset 08h (see Section 8.3) is cleared.
11
RSVD
R
10 ‡
enab_mpeg_ts
RW
9
RSVD
R
8‡
enab_dv_ts
RW
Reserved. Bit 11 returns 0 when read.
Enable MPEG CIP timestamp enhancement. When bit 9 is set to 1, the enhancement is enabled for
MPEG CIP transmit streams (FMT = 20h).
Reserved. Bit 9 returns 0 when read.
Enable DV CIP timestamp enhancement. When bit 8 is set to 1, the enhancement is enabled for DV
CIP transmit streams (FMT = 00h).
‡ One or more bits in this register are cleared only by the assertion of GRST.
7–17
Table 7–21. Link Enhancement Control Register Description (Continued)
BIT
FIELD NAME
TYPE
DESCRIPTION
7‡
enab_unfair
RW
Enable asynchronous priority requests. OHCI-Lynx compatible. Setting bit 7 to 1 enables the link to
respond to requests with priority arbitration. It is recommended that this bit be set to 1.
6
RSVD
R
This bit is not assigned in the PCI7410 follow-on products, because this bit location loaded by the serial
EEPROM from the enhancements field corresponds to bit 23 (programPhyEnable) in the host
controller control register at OHCI offset 50h/54h (see Section 8.16).
5–3
RSVD
R
Reserved. Bits 5–3 return 0s when read.
2‡
RSVD
R
Reserved. Bit 2 returns 0 when read.
1‡
enab_accel
RW
0
RSVD
R
Enable acceleration enhancements. OHCI-Lynx compatible. When bit 1 is set to 1, the PHY layer
is notified that the link supports the IEEE Std 1394a-2000 acceleration enhancements, that is,
ack-accelerated, fly-by concatenation, etc. It is recommended that this bit be set to 1.
Reserved. Bit 0 returns 0 when read.
‡ One or more bits in this register are cleared only by the assertion of GRST.
7.25 Subsystem Access Register
Write access to the subsystem access register updates the subsystem identification registers identically to
OHCI-Lynx. The system ID value written to this register may also be read back from this register. See Table 7–22
for a complete description of the register contents.
Bit
31
30
29
28
27
26
25
Name
Type
24
23
22
21
20
19
18
17
16
Subsystem access
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Subsystem access
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Subsystem access
F8h
Read/Write
0000 0000h
Table 7–22. Subsystem Access Register Description
BIT
FIELD NAME
TYPE
31–16
SUBDEV_ID
RW
Subsystem device ID alias. This field indicates the subsystem device ID.
15–0
SUBVEN_ID
RW
Subsystem vendor ID alias. This field indicates the subsystem vendor ID.
7–18
DESCRIPTION
8 OHCI Registers
The OHCI registers defined by the 1394 Open Host Controller Interface Specification are memory-mapped into a
2K-byte region of memory pointed to by the OHCI base address register at offset 10h in PCI configuration space (see
Section 7.8). These registers are the primary interface for controlling the PCI7410 IEEE 1394 link function.
This section provides the register interface and bit descriptions. Several set/clear register pairs in this programming
model are implemented to solve various issues with typical read-modify-write control registers. There are two
addresses for a set/clear register: RegisterSet and RegisterClear. See Table 8–1 for a register listing. A 1 bit written
to RegisterSet causes the corresponding bit in the set/clear register to be set to 1; a 0 bit leaves the corresponding
bit unaffected. A 1 bit written to RegisterClear causes the corresponding bit in the set/clear register to be cleared;
a 0 bit leaves the corresponding bit in the set/clear register unaffected.
Typically, a read from either RegisterSet or RegisterClear returns the contents of the set or clear register, respectively.
However, sometimes reading the RegisterClear provides a masked version of the set or clear register. The interrupt
event register is an example of this behavior.
Table 8–1. OHCI Register Map
DMA CONTEXT
—
REGISTER NAME
ABBREVIATION
OFFSET
OHCI version
Version
00h
GUID ROM
GUID_ROM
04h
Asynchronous transmit retries
ATRetries
08h
CSR data
CSRData
0Ch
CSR compare
CSRCompareData
10h
CSR control
CSRControl
14h
Configuration ROM header
ConfigROMhdr
18h
Bus identification
BusID
1Ch
Bus options ‡
BusOptions
20h
GUID high ‡
GUIDHi
24h
GUID low ‡
GUIDLo
28h
Reserved
—
Configuration ROM mapping
ConfigROMmap
34h
Posted write address low
PostedWriteAddressLo
38h
Posted write address high
PostedWriteAddressHi
3Ch
Vendor ID
VendorID
40h
Reserved
—
Host controller control ‡
Reserved
2Ch–30h
44h–4Ch
HCControlSet
50h
HCControlClr
54h
—
58h–5Ch
‡ One or more bits in this register are cleared only by the assertion of GRST.
8–1
Table 8–1. OHCI Register Map (Continued)
DMA CONTEXT
Self-ID
REGISTER NAME
OFFSET
—
60h
Self-ID buffer pointer
SelfIDBuffer
64h
Self-ID count
SelfIDCount
68h
Reserved
—
6Ch
IRChannelMaskHiSet
70h
IRChannelMaskHiClear
74h
IRChannelMaskLoSet
78h
IRChannelMaskLoClear
7Ch
IntEventSet
80h
IntEventClear
84h
—
Isochronous receive channel mask high
Isochronous receive channel mask low
Interrupt event
Interrupt mask
Isochronous transmit interrupt event
Isochronous transmit interrupt mask
—
Isochronous receive interrupt event
IntMaskSet
88h
IntMaskClear
8Ch
IsoXmitIntEventSet
90h
IsoXmitIntEventClear
94h
IsoXmitIntMaskSet
98h
IsoXmitIntMaskClear
9Ch
IsoRecvIntEventSet
A0h
IsoRecvIntEventClear
A4h
IsoRecvIntMaskSet
A8h
IsoRecvIntMaskClear
ACh
Initial bandwidth available
InitialBandwidthAvailable
B0h
Initial channels available high
InitialChannelsAvailableHi
B4h
Initial channels available low
InitialChannelsAvailableLo
Reserved
—
Fairness control
FairnessControl
DCh
LinkControlSet
E0h
LinkControlClear
E4h
Isochronous receive interrupt mask
Link control ‡
B8h
BCh–D8h
Node identification
NodeID
E8h
PHY layer control
PhyControl
ECh
Isochronous cycle timer
Isocyctimer
Reserved
—
Asynchronous request filter high
Asynchronous request filter low
Physical request filter high
F0h
F4h–FCh
AsyncRequestFilterHiSet
100h
AsyncRequestFilterHiClear
104h
AsyncRequestFilterLoSet
108h
AsyncRequestFilterLoClear
10Ch
PhysicalRequestFilterHiSet
110h
PhysicalRequestFilterHiClear
114h
PhysicalRequestFilterLoSet
118h
PhysicalRequestFilterLoClear
11Ch
Physical upper bound
PhysicalUpperBound
120h
Reserved
—
Physical request filter low
‡ One or more bits in this register are cleared only by the assertion of GRST.
8–2
ABBREVIATION
Reserved
124h–17Ch
Table 8–1. OHCI Register Map (Continued)
DMA CONTEXT
Asynchronous
Request Transmit
[ ATRQ
Q]
Asynchronous
Response
Res
onse Transmit
[ ATRS ]
Asynchronous
Request Receive
[ ARRQ
Q]
Asynchronous
Response
Res
onse Receive
[ ARRS ]
REGISTER NAME
Asynchronous context control
Transmit Context n
n = 0, 1, 2, 3, …, 7
184h
—
188h
CommandPtr
18Ch
Reserved
—
190h–19Ch
ContextControlSet
1A0h
ContextControlClear
1A4h
Reserved
—
1A8h
Asynchronous context command pointer
CommandPtr
Reserved
—
Asynchronous context control
1ACh
1B0h–1BCh
ContextControlSet
1C0h
ContextControlClear
1C4h
Reserved
—
1C8h
Asynchronous context command pointer
CommandPtr
Reserved
—
Asynchronous context control
Asynchronous context control
1CCh
1D0h–1DCh
ContextControlSet
1E0h
ContextControlClear
1E4h
Reserved
—
1E8h
Asynchronous context command pointer
CommandPtr
1ECh
Reserved
—
1F0h–1FCh
ContextControlSet
200h + 16*n
ContextControlClear
204h + 16*n
Reserved
—
208h + 16*n
Isochronous transmit context command
pointer
CommandPtr
20Ch + 16*n
Reserved
—
210h–3FCh
ContextControlSet
400h + 32*n
ContextControlClear
404h + 32*n
Reserved
—
408h + 32*n
Isochronous receive context command
pointer
CommandPtr
40Ch + 32*n
Isochronous receive context match
ContextMatch
410h + 32*n
Isochronous
n = 0, 1, 2, 3
180h
ContextControlClear
Asynchronous context command pointer
Isochronous receive context control
Receive Context n
OFFSET
Reserved
Isochronous transmit context control
Isochronous
ABBREVIATION
ContextControlSet
8–3
8.1 OHCI Version Register
The OHCI version register indicates the OHCI version support and whether or not the serial EEPROM is present. See
Table 8–2 for a complete description of the register contents.
Bit
31
30
29
28
27
26
25
Name
24
23
22
21
20
19
18
17
16
OHCI version
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
X
0
0
0
0
0
0
0
1
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
OHCI version
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
Register:
Offset:
Type:
Default:
OHCI version
00h
Read-only
0X01 0010h
Table 8–2. OHCI Version Register Description
BIT
FIELD NAME
TYPE
31–25
RSVD
R
Reserved. Bits 31–25 return 0s when read.
24
GUID_ROM
R
The PCI7410 device sets bit 24 to 1 if the serial EEPROM is detected. If the serial EEPROM is present,
then the Bus_Info_Block is automatically loaded on system (hardware) reset.
23–16
version
R
Major version of the OHCI. The PCI7410 device is compliant with the 1394 Open Host Controller
Interface Specification (Release 1.1); thus, this field reads 01h.
15–8
RSVD
R
Reserved. Bits 15–8 return 0s when read.
7–0
revision
R
Minor version of the OHCI. The PCI7410 device is compliant with the 1394 Open Host Controller
Interface Specification (Release 1.1); thus, this field reads 10h.
8–4
DESCRIPTION
8.2 GUID ROM Register
The GUID ROM register accesses the serial EEPROM, and is only applicable if bit 24 (GUID_ROM) in the OHCI
version register at OHCI offset 00h (see Section 8.1) is set to 1. See Table 8–3 for a complete description of the
register contents.
Bit
31
30
29
28
27
26
25
Name
Type
24
23
22
21
20
19
18
17
16
GUID ROM
RSU
R
R
R
R
R
RSU
R
RU
RU
RU
RU
RU
RU
RU
RU
Default
0
0
0
0
0
0
0
0
X
X
X
X
X
X
X
X
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
GUID ROM
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
GUID ROM
04h
Read/Set/Update, Read/Update, Read-only
00XX 0000h
Table 8–3. GUID ROM Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31
addrReset
RSU
Software sets bit 31 to 1 to reset the GUID ROM address to 0. When the PCI7410 device completes
the reset, it clears this bit. The PCI7410 device does not automatically fill bits 23–16 (rdData field) with
the 0th byte.
30–26
RSVD
R
25
rdStart
RSU
Reserved. Bits 30–26 return 0s when read.
A read of the currently addressed byte is started when bit 25 is set to 1. This bit is automatically cleared
when the PCI7410 device completes the read of the currently addressed GUID ROM byte.
24
RSVD
R
23–16
rdData
RU
Reserved. Bit 24 returns 0 when read.
15–8
RSVD
R
Reserved. Bits 15–8 return 0s when read.
7–0
miniROM
R
The miniROM field defaults to 0 indicating that no mini-ROM is implemented. If bit 5 of EEPROM offset
6h is set to 1, then this field returns 20h indicating that valid mini-ROM data begins at offset 20h of the
GUID ROM.
This field contains the data read from the GUID ROM.
8–5
8.3 Asynchronous Transmit Retries Register
The asynchronous transmit retries register indicates the number of times the PCI7410 device attempts a retry for
asynchronous DMA request transmit and for asynchronous physical and DMA response transmit. See Table 8–4 for
a complete description of the register contents.
Bit
31
30
29
28
27
26
Name
Type
25
24
23
22
21
20
19
18
17
16
Asynchronous transmit retries
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Type
R
R
R
R
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Name
Asynchronous transmit retries
Register:
Offset:
Type:
Default:
Asynchronous transmit retries
08h
Read/Write, Read-only
0000 0000h
Table 8–4. Asynchronous Transmit Retries Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31–29
secondLimit
R
The second limit field returns 0s when read, because outbound dual-phase retry is not
implemented.
28–16
cycleLimit
R
The cycle limit field returns 0s when read, because outbound dual-phase retry is not implemented.
Reserved. Bits 15–12 return 0s when read.
15–12
RSVD
R
11–8
maxPhysRespRetries
RW
This field tells the physical response unit how many times to attempt to retry the transmit operation
for the response packet when a busy acknowledge or ack_data_error is received from the target
node.
7–4
maxATRespRetries
RW
This field tells the asynchronous transmit response unit how many times to attempt to retry the
transmit operation for the response packet when a busy acknowledge or ack_data_error is
received from the target node.
3–0
maxATReqRetries
RW
This field tells the asynchronous transmit DMA request unit how many times to attempt to retry the
transmit operation for the response packet when a busy acknowledge or ack_data_error is
received from the target node.
8.4 CSR Data Register
The CSR data register accesses the bus management CSR registers from the host through compare-swap
operations. This register contains the data to be stored in a CSR if the compare is successful.
Bit
31
30
29
28
27
26
25
Name
Type
24
23
22
21
20
19
18
17
16
CSR data
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Name
CSR data
Register:
Offset:
Type:
Default:
8–6
CSR data
0Ch
Read-only
XXXX XXXXh
8.5 CSR Compare Register
The CSR compare register accesses the bus management CSR registers from the host through compare-swap
operations. This register contains the data to be compared with the existing value of the CSR resource.
Bit
31
30
29
28
27
26
25
Name
24
23
22
21
20
19
18
17
16
CSR compare
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
CSR compare
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Register:
Offset:
Type:
Default:
CSR compare
10h
Read-only
XXXX XXXXh
8.6 CSR Control Register
The CSR control register accesses the bus management CSR registers from the host through compare-swap
operations. This register controls the compare-swap operation and selects the CSR resource. See Table 8–5 for a
complete description of the register contents.
Bit
31
30
29
28
27
26
25
RU
R
R
R
R
R
R
R
Default
1
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
Name
Type
24
23
22
21
20
19
18
17
16
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
7
6
5
4
3
2
1
0
CSR control
Name
CSR control
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
RW
RW
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
X
X
Register:
Offset:
Type:
Default:
CSR control
14h
Read/Write, Read/Update, Read-only
8000 000Xh
Table 8–5. CSR Control Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31
csrDone
RU
Bit 31 is set to 1 by the PCI7410 device when a compare-swap operation is complete. It is cleared
whenever this register is written.
30–2
RSVD
R
1–0
csrSel
RW
Reserved. Bits 30–2 return 0s when read.
This field selects the CSR resource as follows:
00 = BUS_MANAGER_ID
01 = BANDWIDTH_AVAILABLE
10 = CHANNELS_AVAILABLE_HI
11 = CHANNELS_AVAILABLE_LO
8–7
8.7 Configuration ROM Header Register
The configuration ROM header register externally maps to the first quadlet of the 1394 configuration ROM, offset
FFFF F000 0400h. See Table 8–6 for a complete description of the register contents.
Bit
31
30
29
28
27
26
Name
Type
25
24
23
22
21
20
19
18
17
16
Configuration ROM header
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Configuration ROM header
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Register:
Offset:
Type:
Default:
Configuration ROM header
18h
Read/Write
0000 XXXXh
Table 8–6. Configuration ROM Header Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31–24
info_length
RW
IEEE 1394 bus-management field. Must be valid when bit 17 (linkEnable) in the host controller control
register at OHCI offset 50h/54h (see Section 8.16) is set to 1.
23–16
crc_length
RW
IEEE 1394 bus-management field. Must be valid when bit 17 (linkEnable) in the host controller control
register at OHCI offset 50h/54h (see Section 8.16) is set to 1.
15–0
rom_crc_value
RW
IEEE 1394 bus-management field. Must be valid at any time bit 17 (linkEnable) in the host controller
control register at OHCI offset 50h/54h (see Section 8.16) is set to 1. The reset value is undefined if
no serial EEPROM is present. If a serial EEPROM is present, then this field is loaded from the serial
EEPROM.
8.8 Bus Identification Register
The bus identification register externally maps to the first quadlet in the Bus_Info_Block and contains the constant
3133 3934h, which is the ASCII value of 1394.
Bit
31
30
29
28
27
26
25
Type
R
R
R
R
R
R
R
R
Default
0
0
1
1
0
0
0
1
Bit
15
14
13
12
11
10
9
8
Name
24
23
22
21
20
19
18
17
16
R
R
R
R
R
R
R
R
0
0
1
1
0
0
1
1
7
6
5
4
3
2
1
0
Bus identification
Name
Bus identification
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
1
1
1
0
0
1
0
0
1
1
0
1
0
0
Register:
Offset:
Type:
Default:
8–8
Bus identification
1Ch
Read-only
3133 3934h
8.9 Bus Options Register
The bus options register externally maps to the second quadlet of the Bus_Info_Block. See Table 8–7 for a complete
description of the register contents.
Bit
31
30
29
28
27
26
25
Name
Type
24
23
22
21
20
19
18
17
16
Bus options
RW
RW
RW
RW
RW
R
R
R
RW
RW
RW
RW
RW
RW
RW
RW
Default
X
X
X
X
0
0
0
0
X
X
X
X
X
X
X
X
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RW
RW
RW
RW
R
R
R
R
RW
RW
R
R
R
R
R
R
1
0
1
0
0
0
0
0
X
X
0
0
0
0
1
0
Name
Type
Default
Bus options
Register:
Offset:
Type:
Default:
Bus options
20h
Read/Write, Read-only
X0XX A0X2h
Table 8–7. Bus Options Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31
irmc
RW
Isochronous resource-manager capable. IEEE 1394 bus-management field. Must be valid when
bit 17 (linkEnable) in the host controller control register at OHCI offset 50h/54h (see Section 8.16)
is set to 1.
30
cmc
RW
Cycle master capable. IEEE 1394 bus-management field. Must be valid when bit 17 (linkEnable) in
the host controller control register at OHCI offset 50h/54h (see Section 8.16) is set to 1.
29
isc
RW
Isochronous support capable. IEEE 1394 bus-management field. Must be valid when bit 17
(linkEnable) in the host controller control register at OHCI offset 50h/54h (see Section 8.16) is set
to 1.
28
bmc
RW
Bus manager capable. IEEE 1394 bus-management field. Must be valid when bit 17 (linkEnable) in
the host controller control register at OHCI offset 50h/54h (see Section 8.16) is set to 1.
27
pmc
RW
Power-management capable. IEEE 1394 bus-management field. When bit 27 is set to 1, this
indicates that the node is power-management capable. Must be valid when bit 17 (linkEnable) in the
host controller control register at OHCI offset 50h/54h (see Section 8.16) is set to 1.
26–24
RSVD
R
23–16
cyc_clk_acc
RW
Reserved. Bits 26–24 return 0s when read.
Cycle master clock accuracy, in parts per million. IEEE 1394 bus-management field. Must be valid
when bit 17 (linkEnable) in the host controller control register at OHCI offset 50h/54h (see
Section 8.16) is set to 1.
15–12 ‡
max_rec
RW
Maximum request. IEEE 1394 bus-management field. Hardware initializes this field to indicate the
maximum number of bytes in a block request packet that is supported by the implementation. This
value, max_rec_bytes, must be 512 or greater, and is calculated by 2^(max_rec + 1). Software may
change this field; however, this field must be valid at any time bit 17 (linkEnable) in the host controller
control register at OHCI offset 50h/54h (see Section 8.16) is set to 1. A received block write request
packet with a length greater than max_rec_bytes may generate an ack_type_error. This field is not
affected by a software reset, and defaults to value indicating 2048 bytes on a system (hardware)
reset.
11–8
RSVD
R
7–6
g
RW
5–3
RSVD
R
Reserved. Bits 5–3 return 0s when read.
2–0
Lnk_spd
R
Link speed. This field returns 010, indicating that the link speeds of 100M bits/s, 200M bits/s, and
400M bits/s are supported.
Reserved. Bits 11–8 return 0s when read.
Generation counter. This field is incremented if any portion of the configuration ROM has been
incremented since the prior bus reset.
‡ One or more bits in this register are cleared only by the assertion of GRST.
8–9
8.10 GUID High Register
The GUID high register represents the upper quadlet in a 64-bit global unique ID (GUID) which maps to the third
quadlet in the Bus_Info_Block. This register contains node_vendor_ID and chip_ID_hi fields. This register initializes
to 0s on a system (hardware) reset, which is an illegal GUID value. If a serial EEPROM is detected, then the contents
of this register are loaded through the serial EEPROM interface after a PRST. At that point, the contents of this register
cannot be changed. If no serial EEPROM is detected, then the contents of this register are loaded by the BIOS after
a PRST. At that point, the contents of this register cannot be changed. All bits in this register are reset by GRST only.
Bit
31
30
29
28
27
26
25
Name
24
23
22
21
20
19
18
17
16
GUID high
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
GUID high
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
GUID high
24h
Read-only
0000 0000h
8.11 GUID Low Register
The GUID low register represents the lower quadlet in a 64-bit global unique ID (GUID) which maps to chip_ID_lo
in the Bus_Info_Block. This register initializes to 0s on a system (hardware) reset and behaves identical to the GUID
high register at OHCI offset 24h (see Section 8.10). All bits in this register are reset by GRST only.
Bit
31
30
29
28
27
26
25
Name
24
23
22
21
20
19
18
17
16
GUID low
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
GUID low
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
8–10
GUID low
28h
Read-only
0000 0000h
8.12 Configuration ROM Mapping Register
The configuration ROM mapping register contains the start address within system memory that maps to the start
address of 1394 configuration ROM for this node. See Table 8–8 for a complete description of the register contents.
Bit
31
30
29
28
27
26
Name
Type
25
24
23
22
21
20
19
18
17
16
Configuration ROM mapping
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Configuration ROM mapping
RW
RW
RW
RW
RW
RW
R
R
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Configuration ROM mapping
34h
Read/Write
0000 0000h
Table 8–8. Configuration ROM Mapping Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31–10
configROMaddr
RW
If a quadlet read request to 1394 offset FFFF F000 0400h through offset FFFF F000 07FFh is
received, then the low-order 10 bits of the offset are added to this register to determine the host memory
address of the read request.
9–0
RSVD
R
Reserved. Bits 9–0 return 0s when read.
8.13 Posted Write Address Low Register
The posted write address low register communicates error information if a write request is posted and an error occurs
while the posted data packet is being written. See Table 8–9 for a complete description of the register contents.
Bit
31
30
29
28
27
26
25
RU
RU
RU
RU
RU
RU
RU
RU
RU
Default
X
X
X
X
X
X
X
X
X
Bit
15
14
13
12
11
10
9
8
7
Name
Type
Default
23
22
21
20
19
18
17
16
RU
RU
RU
RU
RU
RU
RU
X
X
X
X
X
X
X
6
5
4
3
2
1
0
Posted write address low
Name
Type
24
Posted write address low
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Register:
Offset:
Type:
Default:
Posted write address low
38h
Read/Update
XXXX XXXXh
Table 8–9. Posted Write Address Low Register Description
BIT
FIELD NAME
TYPE
31–0
offsetLo
RU
DESCRIPTION
The lower 32 bits of the 1394 destination offset of the write request that failed.
8–11
8.14 Posted Write Address High Register
The posted write address high register communicates error information if a write request is posted and an error occurs
while writing the posted data packet. See Table 8–10 for a complete description of the register contents.
Bit
31
30
29
28
27
26
Name
Type
25
24
23
22
21
20
19
18
17
16
Posted write address high
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
Default
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Posted write address high
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Register:
Offset:
Type:
Default:
Posted write address high
3Ch
Read/Update
XXXX XXXXh
Table 8–10. Posted Write Address High Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31–16
sourceID
RU
This field is the 10-bit bus number (bits 31–22) and 6-bit node number (bits 21–16) of the node that
issued the write request that failed.
15–0
offsetHi
RU
The upper 16 bits of the 1394 destination offset of the write request that failed.
8.15 Vendor ID Register
The vendor ID register holds the company ID of an organization that specifies any vendor-unique registers. The
PCI7410 device implements Texas Instruments unique behavior with regards to OHCI. Thus, this register is read-only
and returns 0108 0028h when read.
Bit
31
30
29
28
27
26
25
Name
24
23
22
21
20
19
18
17
16
Vendor ID
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
1
0
0
0
0
1
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Vendor ID
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
1
0
1
0
0
0
Register:
Offset:
Type:
Default:
8–12
Vendor ID
40h
Read-only
0108 0028h
8.16 Host Controller Control Register
The host controller control set/clear register pair provides flags for controlling the PCI7410 device. See Table 8–11
for a complete description of the register contents.
Bit
31
30
29
28
27
26
25
Name
Type
24
23
22
21
20
19
18
17
16
Host controller control
RSU
RSC
RSC
R
R
R
R
R
R
RSC
R
R
RSC
RSC
RSC
RSCU
Default
0
X
0
0
0
0
0
0
1
0
0
0
0
X
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Host controller control
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Host controller control
50h
set register
54h
clear register
Read/Set/Clear/Update, Read/Set/Clear, Read/Clear, Read-only
X08X 0000h
Table 8–11. Host Controller Control Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31
BIBimage Valid
RSU
When bit 31 is set to 1, the PCI7410 physical response unit is enabled to respond to block read
requests to host configuration ROM and to the mechanism for atomically updating configuration
ROM. Software creates a valid image of the bus_info_block in host configuration ROM before
setting this bit.
When this bit is cleared, the PCI7410 device returns ack_type_error on block read requests to
host configuration ROM. Also, when this bit is cleared and a 1394 bus reset occurs, the
configuration ROM mapping register at OHCI offset 34h (see Section 8.12), configuration ROM
header register at OHCI offset 18h (see Section 8.7), and bus options register at OHCI offset 20h
(see Section 8.9) are not updated.
Software can set this bit only when bit 17 (linkEnable) is 0. Once bit 31 is set to 1, it can be cleared
by a system (hardware) reset, a software reset, or if a fetch error occurs when the PCI7410 device
loads bus_info_block registers from host memory.
30
noByteSwapData
RSC
Bit 30 controls whether physical accesses to locations outside the PCI7410 device itself, as well
as any other DMA data accesses are byte swapped.
29
AckTardyEnable
RSC
Bit 29 controls the acknowledgement of ack_tardy. When bit 29 is set to 1, ack_tardy may be
returned as an acknowledgment to accesses from the 1394 bus to the PCI7410 device, including
accesses to the bus_info_block. The PCI7410 device returns ack_tardy to all other asynchronous
packets addressed to the PCI7410 node. When the PCI7410 device sends ack_tardy, bit 27
(ack_tardy) in the interrupt event register at OHCI offset 80h/84h (see Section 8.21) is set to 1
to indicate the attempted asynchronous access.
Software ensures that bit 27 (ack_tardy) in the interrupt event register is 0. Software also unmasks
wake-up interrupt events such as bit 19 (phy) and bit 27 (ack_tardy) in the interrupt event register
before placing the PCI7410 device into the D1 power mode.
Software must not set this bit if the PCI7410 node is the 1394 bus manager.
28–24
RSVD
R
Reserved. Bits 28–24 return 0s when read.
23 ‡
programPhyEnable
R
Bit 23 informs upper-level software that lower-level software has consistently configured the IEEE
1394a-2000 enhancements in the link and PHY layers. When this bit is 1, generic software such
as the OHCI driver is responsible for configuring IEEE 1394a-2000 enhancements in the PHY
layer and bit 22 (aPhyEnhanceEnable). When this bit is 0, the generic software may not modify
the IEEE 1394a-2000 enhancements in the PHY layer and cannot interpret the setting of bit 22
(aPhyEnhanceEnable). This bit is initialized from serial EEPROM. This bit defaults to 1.
‡ One or more bits in this register are cleared only by the assertion of GRST.
8–13
Table 8–11. Host Controller Control Register Description (Continued)
BIT
FIELD NAME
TYPE
DESCRIPTION
22
aPhyEnhanceEnable
RSC
When bits 23 (programPhyEnable) and 17 (linkEnable) are 1, the OHCI driver can set bit 22 to
1 to use all IEEE 1394a-2000 enhancements. When bit 23 (programPhyEnable) is cleared to 0,
the software does not change PHY enhancements or this bit.
21–20
RSVD
R
19
LPS
RSC
Reserved. Bits 21 and 20 return 0s when read.
Bit 19 controls the link power status. Software must set this bit to 1 to permit the link-PHY
communication. A 0 prevents link-PHY communication.
The OHCI-link is divided into two clock domains (PCLK and PHY_SCLK). If software tries to
access any register in the PHY_SCLK domain while the PHY_SCLK is disabled, then a target
abort is issued by the link. This problem can be avoided by setting bit 4 (DIS_TGT_ABT) to 1 in
the PCI miscellaneous configuration register at offset F0h in the PCI configuration space (see
Section 7.23). This allows the link to respond to these types of request by returning all Fs (hex).
OHCI registers at offsets DCh–F0h and 100h–11Ch are in the PHY_SCLK domain.
After setting LPS, software must wait approximately 10 ms before attempting to access any of
the OHCI registers. This gives the PHY_SCLK time to stabilize.
18
postedWriteEnable
RSC
Bit 18 enables (1) or disables (0) posted writes. Software changes this bit only when bit 17
(linkEnable) is 0.
17
linkEnable
RSC
Bit 17 is cleared to 0 by either a system (hardware) or software reset. Software must set this bit
to 1 when the system is ready to begin operation and then force a bus reset. This bit is necessary
to keep other nodes from sending transactions before the local system is ready. When this bit is
cleared, the PCI7410 device is logically and immediately disconnected from the 1394 bus, no
packets are received or processed, nor are packets transmitted.
16
SoftReset
RSCU
When bit 16 is set to 1, all PCI7410 states are reset, all FIFOs are flushed, and all OHCI registers
are set to their system (hardware) reset values, unless otherwise specified. PCI registers are not
affected by this bit. This bit remains set to 1 while the software reset is in progress and reverts
back to 0 when the reset has completed.
15–0
RSVD
R
Reserved. Bits 15–0 return 0s when read.
8.17 Self-ID Buffer Pointer Register
The self-ID buffer pointer register points to the 2K-byte aligned base address of the buffer in host memory where the
self-ID packets are stored during bus initialization. Bits 31–11 are read/write accessible. Bits 10–0 are reserved, and
return 0s when read.
Bit
31
30
29
28
27
26
25
RW
RW
RW
RW
RW
RW
RW
RW
Default
X
X
X
X
X
X
X
X
Bit
15
14
13
12
11
10
9
8
Name
Type
Default
22
21
20
19
18
17
16
RW
RW
RW
RW
RW
RW
RW
RW
X
X
X
X
X
X
X
X
7
6
5
4
3
2
1
0
Self-ID buffer pointer
RW
RW
RW
RW
RW
R
R
R
R
R
R
R
R
R
R
R
X
X
X
X
X
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
8–14
23
Self-ID buffer pointer
Name
Type
24
Self-ID buffer pointer
64h
Read/Write, Read-only
XXXX XX00h
8.18 Self-ID Count Register
The self-ID count register keeps a count of the number of times the bus self-ID process has occurred, flags self-ID
packet errors, and keeps a count of the self-ID data in the self-ID buffer. See Table 8–12 for a complete description
of the register contents.
Bit
31
30
29
28
27
26
25
Name
Type
24
23
22
21
20
19
18
17
16
Self-ID count
RU
R
R
R
R
R
R
R
RU
RU
RU
RU
RU
RU
RU
RU
Default
X
0
0
0
0
0
0
0
X
X
X
X
X
X
X
X
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Self-ID count
Type
R
R
R
R
R
RU
RU
RU
RU
RU
RU
RU
RU
RU
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Self-ID count
68h
Read/Update, Read-only
X0XX 0000h
Table 8–12. Self-ID Count Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31
selfIDError
RU
When bit 31 is set to 1, an error was detected during the most recent self-ID packet reception. The
contents of the self-ID buffer are undefined. This bit is cleared after a self-ID reception in which no
errors are detected. Note that an error can be a hardware error or a host bus write error.
30–24
RSVD
R
23–16
selfIDGeneration
RU
15–11
RSVD
R
10–2
selfIDSize
RU
1–0
RSVD
R
Reserved. Bits 30–24 return 0s when read.
The value in this field increments each time a bus reset is detected. This field rolls over to 0 after
reaching 255.
Reserved. Bits 15–11 return 0s when read.
This field indicates the number of quadlets that have been written into the self-ID buffer for the current
bits 23–16 (selfIDGeneration field). This includes the header quadlet and the self-ID data. This field
is cleared to 0s when the self-ID reception begins.
Reserved. Bits 1 and 0 return 0s when read.
8–15
8.19 Isochronous Receive Channel Mask High Register
The isochronous receive channel mask high set/clear register enables packet receives from the upper 32
isochronous data channels. A read from either the set register or clear register returns the content of the isochronous
receive channel mask high register. See Table 8–13 for a complete description of the register contents.
Bit
31
30
29
28
27
Name
Type
26
25
24
23
22
21
20
19
18
17
16
Isochronous receive channel mask high
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
Default
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Isochronous receive channel mask high
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Register:
Offset:
Type:
Default:
Isochronous receive channel mask high
70h
set register
74h
clear register
Read/Set/Clear
XXXX XXXXh
Table 8–13. Isochronous Receive Channel Mask High Register Description
8–16
BIT
FIELD NAME
TYPE
DESCRIPTION
31
isoChannel63
RSC
When bit 31 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 63.
30
isoChannel62
RSC
When bit 30 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 62.
29
isoChannel61
RSC
When bit 29 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 61.
28
isoChannel60
RSC
When bit 28 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 60.
27
isoChannel59
RSC
When bit 27 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 59.
26
isoChannel58
RSC
When bit 26 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 58.
25
isoChannel57
RSC
When bit 25 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 57.
24
isoChannel56
RSC
When bit 24 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 56.
23
isoChannel55
RSC
When bit 23 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 55.
22
isoChannel54
RSC
When bit 22 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 54.
21
isoChannel53
RSC
When bit 21 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 53.
20
isoChannel52
RSC
When bit 20 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 52.
19
isoChannel51
RSC
When bit 19 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 51.
18
isoChannel50
RSC
When bit 18 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 50.
17
isoChannel49
RSC
When bit 17 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 49.
16
isoChannel48
RSC
When bit 16 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 48.
15
isoChannel47
RSC
When bit 15 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 47.
14
isoChannel46
RSC
When bit 14 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 46.
13
isoChannel45
RSC
When bit 13 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 45.
12
isoChannel44
RSC
When bit 12 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 44.
11
isoChannel43
RSC
When bit 11 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 43.
10
isoChannel42
RSC
When bit 10 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 42.
9
isoChannel41
RSC
When bit 9 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 41.
8
isoChannel40
RSC
When bit 8 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 40.
7
isoChannel39
RSC
When bit 7 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 39.
Table 8–13. Isochronous Receive Channel Mask High Register Description (Continued)
BIT
FIELD NAME
TYPE
DESCRIPTION
6
isoChannel38
RSC
When bit 6 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 38.
5
isoChannel37
RSC
When bit 5 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 37.
4
isoChannel36
RSC
When bit 4 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 36.
3
isoChannel35
RSC
When bit 3 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 35.
2
isoChannel34
RSC
When bit 2 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 34.
1
isoChannel33
RSC
When bit 1 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 33.
0
isoChannel32
RSC
When bit 0 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 32.
8.20 Isochronous Receive Channel Mask Low Register
The isochronous receive channel mask low set/clear register enables packet receives from the lower 32 isochronous
data channels. See Table 8–14 for a complete description of the register contents.
Bit
31
30
29
28
27
26
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
Default
X
X
X
X
X
X
X
X
X
X
Bit
15
14
13
12
11
10
9
8
7
6
Name
Type
Default
24
23
22
21
20
19
18
17
16
RSC
RSC
RSC
RSC
RSC
RSC
X
X
X
X
X
X
5
4
3
2
1
0
Isochronous receive channel mask low
Name
Type
25
Isochronous receive channel mask low
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Register:
Offset:
Type:
Default:
Isochronous receive channel mask low
78h
set register
7Ch
clear register
Read/Set/Clear
XXXX XXXXh
Table 8–14. Isochronous Receive Channel Mask Low Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31
isoChannel31
RSC
When bit 31 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 31.
30
isoChannel30
RSC
When bit 30 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 30.
29–2
isoChanneln
RSC
Bits 29 through 2 (isoChanneln, where n = 29, 28, 27, …, 2) follow the same pattern as bits 31 and 30.
1
isoChannel1
RSC
When bit 1 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 1.
0
isoChannel0
RSC
When bit 0 is set to 1, the PCI7410 device is enabled to receive from isochronous channel number 0.
8–17
8.21 Interrupt Event Register
The interrupt event set/clear register reflects the state of the various PCI7410 interrupt sources. The interrupt bits
are set to 1 by an asserting edge of the corresponding interrupt signal or by writing a 1 in the corresponding bit in the
set register. The only mechanism to clear a bit in this register is to write a 1 to the corresponding bit in the clear register.
This register is fully compliant with the 1394 Open Host Controller Interface Specification, and the PCI7410 device
adds a vendor-specific interrupt function to bit 30. When the interrupt event register is read, the return value is the
bit-wise AND function of the interrupt event and interrupt mask registers. See Table 8–15 for a complete description
of the register contents.
Bit
31
30
29
28
27
26
25
24
Type
R
RSC
RSC
R
RSCU
RSCU
RSCU
RSCU
Default
0
X
0
0
0
X
X
X
Bit
15
14
13
12
11
10
9
8
Name
Default
22
21
20
19
18
17
16
RSCU
RSCU
RSCU
RSCU
RSCU
RSCU
RSCU
RSCU
X
X
X
X
X
0
X
X
7
6
5
4
3
2
1
0
Interrupt event
Name
Type
23
Interrupt event
RSCU
R
R
R
R
R
RSCU
RSCU
RU
RU
RSCU
RSCU
RSCU
RSCU
RSCU
RSCU
0
0
0
0
0
0
X
X
X
X
X
X
X
X
X
X
Register:
Offset:
Type:
Default:
Interrupt event
80h
set register
84h
clear register [returns the content of the interrupt event register bit-wise ANDed with
the interrupt mask register when read]
Read/Set/Clear/Update, Read/Set/Clear, Read/Update, Read-only
XXXX 0XXXh
Table 8–15. Interrupt Event Register Description
BIT
FIELD NAME
TYPE
31–30
RSVD
R
29
SoftInterrupt
RSC
28
RSVD
R
27
ack_tardy
RSCU
DESCRIPTION
Reserved. Bits 31 and 30 return 0 when read.
Bit 29 is used by software to generate a PCI7410 interrupt for its own use.
Reserved. Bit 28 returns 0 when read.
Bit 27 is set to 1 when bit 29 (AckTardyEnable) in the host controller control register at OHCI offset
50h/54h (see Section 8.16) is set to 1 and any of the following conditions occur:
a. Data is present in a receive FIFO that is to be delivered to the host.
b. The physical response unit is busy processing requests or sending responses.
c. The PCI7410 device sent an ack_tardy acknowledgment.
8–18
26
phyRegRcvd
RSCU
The PCI7410 device has received a PHY register data byte which can be read from bits 23–16 in the
PHY layer control register at OHCI offset ECh (see Section 8.33).
25
cycleTooLong
RSCU
If bit 21 (cycleMaster) in the link control register at OHCI offset E0h/E4h (see Section 8.31) is set to
1, then this indicates that over 125 µs has elapsed between the start of sending a cycle start packet
and the end of a subaction gap. Bit 21 (cycleMaster) in the link control register is cleared by this event.
24
unrecoverableError
RSCU
This event occurs when the PCI7410 device encounters any error that forces it to stop operations
on any or all of its subunits, for example, when a DMA context sets its dead bit to 1. While bit 24 is
set to 1, all normal interrupts for the context(s) that caused this interrupt are blocked from being set
to 1.
23
cycleInconsistent
RSCU
A cycle start was received that had values for the cycleSeconds and cycleCount fields that are
different from the values in bits 31–25 (cycleSeconds field) and bits 24–12 (cycleCount field) in the
isochronous cycle timer register at OHCI offset F0h (see Section 8.34).
Table 8–15. Interrupt Event Register Description (Continued)
BIT
FIELD NAME
TYPE
DESCRIPTION
22
cycleLost
RSCU
A lost cycle is indicated when no cycle_start packet is sent or received between two successive
cycleSynch events. A lost cycle can be predicted when a cycle_start packet does not immediately
follow the first subaction gap after the cycleSynch event or if an arbitration reset gap is detected after
a cycleSynch event without an intervening cycle start. Bit 22 may be set to 1 either when a lost cycle
occurs or when logic predicts that one will occur.
21
cycle64Seconds
RSCU
Indicates that the 7th bit of the cycle second counter has changed.
20
cycleSynch
RSCU
Indicates that a new isochronous cycle has started. Bit 20 is set to 1 when the low-order bit of the
cycle count toggles.
19
phy
RSCU
Indicates that the PHY layer requests an interrupt through a status transfer.
18
regAccessFail
RSCU
Indicates that a PCI7410 register access has failed due to a missing SCLK clock signal from the PHY
layer. When a register access fails, bit 18 is set to 1 before the next register access.
17
busReset
RSCU
Indicates that the PHY layer has entered bus reset mode.
16
selfIDcomplete
RSCU
A self-ID packet stream has been received. It is generated at the end of the bus initialization process.
Bit 16 is turned off simultaneously when bit 17 (busReset) is turned on.
15
selfIDcomplete2
RSCU
Secondary indication of the end of a self-ID packet stream. Bit 15 is set to 1 by the PCI7410 device
when it sets bit 16 (selfIDcomplete), and retains the state, independent of bit 17 (busReset).
14–10
RSVD
R
9
lockRespErr
RSCU
Reserved. Bits 14–10 return 0s when read.
Indicates that the PCI7410 device sent a lock response for a lock request to a serial bus register, but
did not receive an ack_complete.
8
postedWriteErr
RSCU
Indicates that a host bus error occurred while the PCI7410 device was trying to write a 1394 write
request, which had already been given an ack_complete, into system memory.
7
isochRx
RU
Isochronous receive DMA interrupt. Indicates that one or more isochronous receive contexts have
generated an interrupt. This is not a latched event; it is the logical OR of all bits in the isochronous
receive interrupt event register at OHCI offset A0h/A4h (see Section 8.25) and isochronous receive
interrupt mask register at OHCI offset A8h/ACh (see Section 8.26). The isochronous receive interrupt
event register indicates which contexts have been interrupted.
6
isochTx
RU
Isochronous transmit DMA interrupt. Indicates that one or more isochronous transmit contexts have
generated an interrupt. This is not a latched event; it is the logical OR of all bits in the isochronous
transmit interrupt event register at OHCI offset 90h/94h (see Section 8.23) and isochronous transmit
interrupt mask register at OHCI offset 98h/9Ch (see Section 8.24). The isochronous transmit
interrupt event register indicates which contexts have been interrupted.
5
RSPkt
RSCU
Indicates that a packet was sent to an asynchronous receive response context buffer and the
descriptor xferStatus and resCount fields have been updated.
4
RQPkt
RSCU
Indicates that a packet was sent to an asynchronous receive request context buffer and the
descriptor xferStatus and resCount fields have been updated.
3
ARRS
RSCU
Asynchronous receive response DMA interrupt. Bit 3 is conditionally set to 1 upon completion of an
ARRS DMA context command descriptor.
2
ARRQ
RSCU
Asynchronous receive request DMA interrupt. Bit 2 is conditionally set to 1 upon completion of an
ARRQ DMA context command descriptor.
1
respTxComplete
RSCU
Asynchronous response transmit DMA interrupt. Bit 1 is conditionally set to 1 upon completion of an
ATRS DMA command.
0
reqTxComplete
RSCU
Asynchronous request transmit DMA interrupt. Bit 0 is conditionally set to 1 upon completion of an
ATRQ DMA command.
8–19
8.22 Interrupt Mask Register
The interrupt mask set/clear register enables the various PCI7410 interrupt sources. Reads from either the set
register or the clear register always return the contents of the interrupt mask register. In all cases except
masterIntEnable (bit 31) and vendorSpecific (bit 30), the enables for each interrupt event align with the interrupt event
register bits detailed in Table 8–15.
This register is fully compliant with the 1394 Open Host Controller Interface Specification and the PCI7410 device
adds an interrupt function to bit 30. See Table 8–16 for a complete description of bits 31 and 30.
Bit
31
30
29
28
27
26
25
Name
Type
24
23
22
21
20
19
18
17
16
Interrupt mask
RSCU
RSC
RSC
R
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
Default
X
X
0
0
0
X
X
X
X
X
X
X
X
0
X
X
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Interrupt mask
RSC
R
R
R
R
R
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
0
0
0
0
0
0
X
X
X
X
X
X
X
X
X
X
Register:
Offset:
Type:
Default:
Interrupt mask
88h
set register
8Ch
clear register
Read/Set/Clear/Update, Read/Set/Clear, Read/Update, Read-only
XXXX 0XXXh
Table 8–16. Interrupt Mask Register Description
8–20
BIT
FIELD NAME
TYPE
DESCRIPTION
31
masterIntEnable
RSCU
Master interrupt enable. If bit 31 is set to 1, then external interrupts are generated in accordance with
the interrupt mask register. If this bit is cleared, then external interrupts are not generated regardless
of the interrupt mask register settings.
30
VendorSpecific
RSC
When this bit and bit 30 (vendorSpecific) in the interrupt event register at OHCI offset 80h/84h (see
Section 8.21) are set to 1, this vendor-specific interrupt mask enables interrupt generation.
29
SoftInterrupt
RSC
When this bit and bit 29 (SoftInterrupt) in the interrupt event register at OHCI offset 80h/84h (see
Section 8.21) are set to 1, this soft-interrupt mask enables interrupt generation.
28
RSVD
R
27
ack_tardy
RSC
When this bit and bit 27 (ack_tardy) in the interrupt event register at OHCI offset 80h/84h (see
Section 8.21) are set to 1, this acknowledge-tardy interrupt mask enables interrupt generation.
26
phyRegRcvd
RSC
When this bit and bit 26 (phyRegRcvd) in the interrupt event register at OHCI offset 80h/84h (see
Section 8.21) are set to 1, this PHY-register interrupt mask enables interrupt generation.
25
cycleTooLong
RSC
When this bit and bit 25 (cycleTooLong) in the interrupt event register at OHCI offset 80h/84h (see
Section 8.21) are set to 1, this cycle-too-long interrupt mask enables interrupt generation.
24
unrecoverableError
RSC
When this bit and bit 24 (unrecoverableError) in the interrupt event register at OHCI offset 80h/84h (see
Section 8.21) are set to 1, this unrecoverable-error interrupt mask enables interrupt generation.
23
cycleInconsistent
RSC
When this bit and bit 23 (cycleInconsistent) in the interrupt event register at OHCI offset 80h/84h (see
Section 8.21) are set to 1, this inconsistent-cycle interrupt mask enables interrupt generation.
22
cycleLost
RSC
When this bit and bit 22 (cycleLost) in the interrupt event register at OHCI offset 80h/84h (see
Section 8.21) are set to 1, this lost-cycle interrupt mask enables interrupt generation.
21
cycle64Seconds
RSC
When this bit and bit 21 (cycle64Seconds) in the interrupt event register at OHCI offset 80h/84h (see
Section 8.21) are set to 1, this 64-second-cycle interrupt mask enables interrupt generation.
20
cycleSynch
RSC
When this bit and bit 20 (cycleSynch) in the interrupt event register at OHCI offset 80h/84h (see
Section 8.21) are set to 1, this isochronous-cycle interrupt mask enables interrupt generation.
19
phy
RSC
When this bit and bit 19 (phy) in the interrupt event register at OHCI offset 80h/84h (see Section 8.21)
are set to 1, this PHY-status-transfer interrupt mask enables interrupt generation.
Reserved. Bit 28 returns 0 when read.
Table 8–16. Interrupt Mask Register Description (Continued)
BIT
FIELD NAME
TYPE
DESCRIPTION
18
regAccessFail
RSC
When this bit and bit 18 (regAccessFail) in the interrupt event register at OHCI offset 80h/84h (see
Section 8.21) are set to 1, this register-access-failed interrupt mask enables interrupt generation.
17
busReset
RSC
When this bit and bit 17 (busReset) in the interrupt event register at OHCI offset 80h/84h (see
Section 8.21) are set to 1, this bus-reset interrupt mask enables interrupt generation.
16
selfIDcomplete
RSC
When this bit and bit 16 (selfIDcomplete) in the interrupt event register at OHCI offset 80h/84h (see
Section 8.21) are set to 1, this self-ID-complete interrupt mask enables interrupt generation.
15
selfIDcomplete2
RSC
When this bit and bit 15 (selfIDcomplete2) in the interrupt event register at OHCI offset 80h/84h (see
Section 8.21) are set to 1, this second-self-ID-complete interrupt mask enables interrupt generation.
14–10
RSVD
R
9
lockRespErr
RSC
Reserved. Bits 14–10 return 0s when read.
When this bit and bit 9 (lockRespErr) in the interrupt event register at OHCI offset 80h/84h (see
Section 8.21) are set to 1, this lock-response-error interrupt mask enables interrupt generation.
8
postedWriteErr
RSC
When this bit and bit 8 (postedWriteErr) in the interrupt event register at OHCI offset 80h/84h (see
Section 8.21) are set to 1, this posted-write-error interrupt mask enables interrupt generation.
7
isochRx
RSC
When this bit and bit 7 (isochRx) in the interrupt event register at OHCI offset 80h/84h (see
Section 8.21) are set to 1, this isochronous-receive-DMA interrupt mask enables interrupt generation.
6
isochTx
RSC
When this bit and bit 6 (isochTx) in the interrupt event register at OHCI offset 80h/84h (see
Section 8.21) are set to 1, this isochronous-transmit-DMA interrupt mask enables interrupt generation.
5
RSPkt
RSC
When this bit and bit 5 (RSPkt) in the interrupt event register at OHCI offset 80h/84h (see Section 8.21)
are set to 1, this receive-response-packet interrupt mask enables interrupt generation.
4
RQPkt
RSC
When this bit and bit 4 (RQPkt) in the interrupt event register at OHCI offset 80h/84h (see Section 8.21)
are set to 1, this receive-request-packet interrupt mask enables interrupt generation.
3
ARRS
RSC
When this bit and bit 3 (ARRS) in the interrupt event register at OHCI offset 80h/84h (see Section 8.21)
are set to 1, this asynchronous-receive-response-DMA interrupt mask enables interrupt generation.
2
ARRQ
RSC
When this bit and bit 2 (ARRQ) in the interrupt event register at OHCI offset 80h/84h (see Section 8.21)
are set to 1, this asynchronous-receive-request-DMA interrupt mask enables interrupt generation.
1
respTxComplete
RSC
When this bit and bit 1 (respTxComplete) in the interrupt event register at OHCI offset 80h/84h (see
Section 8.21) are set to 1, this response-transmit-complete interrupt mask enables interrupt
generation.
0
reqTxComplete
RSC
When this bit and bit 0 (reqTxComplete) in the interrupt event register at OHCI offset 80h/84h (see
Section 8.21) are set to 1, this request-transmit-complete interrupt mask enables interrupt generation.
8–21
8.23 Isochronous Transmit Interrupt Event Register
The isochronous transmit interrupt event set/clear register reflects the interrupt state of the isochronous transmit
contexts. An interrupt is generated on behalf of an isochronous transmit context if an OUTPUT_LAST* command
completes and its interrupt bits are set to 1. Upon determining that the isochTx (bit 6) interrupt has occurred in the
interrupt event register at OHCI offset 80h/84h (see Section 8.21), software can check this register to determine which
context(s) caused the interrupt. The interrupt bits are set to 1 by an asserting edge of the corresponding interrupt
signal, or by writing a 1 in the corresponding bit in the set register. The only mechanism to clear a bit in this register
is to write a 1 to the corresponding bit in the clear register. See Table 8–17 for a complete description of the register
contents.
Bit
31
30
29
28
27
26
Name
25
24
23
22
21
20
19
18
17
16
Isochronous transmit interrupt event
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Isochronous transmit interrupt event
Type
R
R
R
R
R
R
R
R
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
Default
0
0
0
0
0
0
0
0
X
X
X
X
X
X
X
X
Register:
Offset:
Isochronous transmit interrupt event
90h
set register
94h
clear register [returns the contents of the isochronous transmit interrupt event
register bit-wise ANDed with the isochronous transmit interrupt mask register
when read]
Read/Set/Clear, Read-only
0000 00XXh
Type:
Default:
Table 8–17. Isochronous Transmit Interrupt Event Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31–8
RSVD
R
7
isoXmit7
RSC
Isochronous transmit channel 7 caused the interrupt event register bit 6 (isochTx) interrupt.
6
isoXmit6
RSC
Isochronous transmit channel 6 caused the interrupt event register bit 6 (isochTx) interrupt.
5
isoXmit5
RSC
Isochronous transmit channel 5 caused the interrupt event register bit 6 (isochTx) interrupt.
4
isoXmit4
RSC
Isochronous transmit channel 4 caused the interrupt event register bit 6 (isochTx) interrupt.
3
isoXmit3
RSC
Isochronous transmit channel 3 caused the interrupt event register bit 6 (isochTx) interrupt.
2
isoXmit2
RSC
Isochronous transmit channel 2 caused the interrupt event register bit 6 (isochTx) interrupt.
1
isoXmit1
RSC
Isochronous transmit channel 1 caused the interrupt event register bit 6 (isochTx) interrupt.
0
isoXmit0
RSC
Isochronous transmit channel 0 caused the interrupt event register bit 6 (isochTx) interrupt.
8–22
Reserved. Bits 31–8 return 0s when read.
8.24 Isochronous Transmit Interrupt Mask Register
The isochronous transmit interrupt mask set/clear register enables the isochTx interrupt source on a per-channel
basis. Reads from either the set register or the clear register always return the contents of the isochronous transmit
interrupt mask register. In all cases the enables for each interrupt event align with the isochronous transmit interrupt
event register bits detailed in Table 8–17.
Bit
31
30
29
28
27
26
Name
25
24
23
22
21
20
19
18
17
16
Isochronous transmit interrupt mask
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Isochronous transmit interrupt mask
Type
R
R
R
R
R
R
R
R
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
Default
0
0
0
0
0
0
0
0
X
X
X
X
X
X
X
X
Register:
Offset:
Type:
Default:
Isochronous transmit interrupt mask
98h
set register
9Ch
clear register
Read/Set/Clear, Read-only
0000 00XXh
8–23
8.25 Isochronous Receive Interrupt Event Register
The isochronous receive interrupt event set/clear register reflects the interrupt state of the isochronous receive
contexts. An interrupt is generated on behalf of an isochronous receive context if an INPUT_* command completes
and its interrupt bits are set to 1. Upon determining that the isochRx (bit 7) interrupt in the interrupt event register at
OHCI offset 80h/84h (see Section 8.21) has occurred, software can check this register to determine which context(s)
caused the interrupt. The interrupt bits are set to 1 by an asserting edge of the corresponding interrupt signal or by
writing a 1 in the corresponding bit in the set register. The only mechanism to clear a bit in this register is to write a
1 to the corresponding bit in the clear register. See Table 8–18 for a complete description of the register contents.
Bit
31
30
29
28
27
26
Name
25
24
23
22
21
20
19
18
17
16
Isochronous receive interrupt event
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Isochronous receive interrupt event
Type
R
R
R
R
R
R
R
R
R
R
R
R
RSC
RSC
RSC
RSC
Default
0
0
0
0
0
0
0
0
0
0
0
0
X
X
X
X
Register:
Offset:
Isochronous receive interrupt event
A0h
set register
A4h
clear register [returns the contents of isochronous receive interrupt event register
bit-wise ANDed with the isochronous receive mask register when read]
Read/Set/Clear, Read-only
0000 000Xh
Type:
Default:
Table 8–18. Isochronous Receive Interrupt Event Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31–4
RSVD
R
3
isoRecv3
RSC
Isochronous receive channel 3 caused the interrupt event register bit 7 (isochRx) interrupt.
2
isoRecv2
RSC
Isochronous receive channel 2 caused the interrupt event register bit 7 (isochRx) interrupt.
1
isoRecv1
RSC
Isochronous receive channel 1 caused the interrupt event register bit 7 (isochRx) interrupt.
0
isoRecv0
RSC
Isochronous receive channel 0 caused the interrupt event register bit 7 (isochRx) interrupt.
8–24
Reserved. Bits 31–4 return 0s when read.
8.26 Isochronous Receive Interrupt Mask Register
The isochronous receive interrupt mask set/clear register enables the isochRx interrupt source on a per-channel
basis. Reads from either the set register or the clear register always return the contents of the isochronous receive
interrupt mask register. In all cases the enables for each interrupt event align with the isochronous receive interrupt
event register bits detailed in Table 8–18.
Bit
31
30
29
28
27
26
R
R
R
R
R
R
R
R
R
Name
Type
25
24
23
22
21
20
19
18
17
16
R
R
R
R
R
R
R
Isochronous receive interrupt mask
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Type
R
R
R
R
R
R
R
R
R
R
R
R
RSC
RSC
RSC
RSC
Default
0
0
0
0
0
0
0
0
0
0
0
0
X
X
X
X
Name
Isochronous receive interrupt mask
Register:
Offset:
Type:
Default:
Isochronous receive interrupt mask
A8h
set register
ACh
clear register
Read/Set/Clear, Read-only
0000 000Xh
8.27 Initial Bandwidth Available Register
The initial bandwidth available register value is loaded into the corresponding bus management CSR register on a
system (hardware) or software reset. See Table 8–19 for a complete description of the register contents.
Bit
31
30
29
28
27
26
Name
25
24
23
22
21
20
19
18
17
16
Initial bandwidth available
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Initial bandwidth available
Type
R
R
R
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Default
0
0
0
1
0
0
1
1
0
0
1
1
0
0
1
1
Register:
Offset:
Type:
Default:
Initial bandwidth available
B0h
Read-only, Read/Write
0000 1333h
Table 8–19. Initial Bandwidth Available Register Description
BIT
FIELD NAME
TYPE
31–13
RSVD
R
12–0
InitBWAvailable
RW
DESCRIPTION
Reserved. Bits 31–13 return 0s when read.
This field is reset to 1333h on a system (hardware) or software reset, and is not affected by a 1394
bus reset. The value of this field is loaded into the BANDWIDTH_AVAILABLE CSR register upon
a GRST, PRST, or a 1394 bus reset.
8–25
8.28 Initial Channels Available High Register
The initial channels available high register value is loaded into the corresponding bus management CSR register on
a system (hardware) or software reset. See Table 8–20 for a complete description of the register contents.
Bit
31
30
29
28
27
26
Name
Type
25
24
23
22
21
20
19
18
17
16
Initial channels available high
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Default
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Initial channels available high
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Register:
Offset:
Type:
Default:
Initial channels available high
B4h
Read/Write
FFFF FFFFh
Table 8–20. Initial Channels Available High Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31–0
InitChanAvailHi
RW
This field is reset to FFFF_FFFFh on a system (hardware) or software reset, and is not affected by
a 1394 bus reset. The value of this field is loaded into the CHANNELS_AVAILABLE_HI CSR
register upon a GRST, PRST, or a 1394 bus reset.
8.29 Initial Channels Available Low Register
The initial channels available low register value is loaded into the corresponding bus management CSR register on
a system (hardware) or software reset. See Table 8–21 for a complete description of the register contents.
Bit
31
30
29
28
27
26
Name
Type
25
24
23
22
21
20
19
18
17
16
Initial channels available low
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Default
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Initial channels available low
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Register:
Offset:
Type:
Default:
Initial channels available low
B8h
Read/Write
FFFF FFFFh
Table 8–21. Initial Channels Available Low Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31–0
InitChanAvailLo
RW
This field is reset to FFFF_FFFFh on a system (hardware) or software reset, and is not affected by
a 1394 bus reset. The value of this field is loaded into the CHANNELS_AVAILABLE_LO CSR
register upon a GRST, PRST, or a 1394 bus reset.
8–26
8.30 Fairness Control Register
The fairness control register provides a mechanism by which software can direct the host controller to transmit
multiple asynchronous requests during a fairness interval. See Table 8–22 for a complete description of the register
contents.
Bit
31
30
29
28
27
26
25
Name
24
23
22
21
20
19
18
17
16
Fairness control
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Fairness control
Type
R
R
R
R
R
R
R
R
RW
RW
RW
RW
RW
RW
RW
RW
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Fairness control
DCh
Read-only
0000 0000h
Table 8–22. Fairness Control Register Description
BIT
FIELD NAME
TYPE
31–8
RSVD
R
7–0
pri_req
RW
DESCRIPTION
Reserved. Bits 31–8 return 0s when read.
This field specifies the maximum number of priority arbitration requests for asynchronous request
packets that the link is permitted to make of the PHY layer during a fairness interval.
8–27
8.31 Link Control Register
The link control set/clear register provides the control flags that enable and configure the link core protocol portions
of the PCI7410 device. It contains controls for the receiver and cycle timer. See Table 8–23 for a complete description
of the register contents.
Bit
31
30
29
28
27
26
25
Name
24
23
22
21
20
19
18
17
16
Link control
Type
R
R
R
R
R
R
R
R
R
RSC
RSCU
RSC
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
X
X
X
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Link control
Type
R
R
R
R
R
RSC
RSC
R
R
RS
R
R
R
R
R
R
Default
0
0
0
0
0
X
X
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Link control
E0h
set register
E4h
clear register
Read/Set/Clear/Update, Read/Set/Clear, Read-only
00X0 0X00h
Table 8–23. Link Control Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31–23
RSVD
R
22
cycleSource
RSC
Reserved. Bits 31–23 return 0s when read.
When bit 22 is set to 1, the cycle timer uses an external source (CYCLEIN) to determine when to roll
over the cycle timer. When this bit is cleared, the cycle timer rolls over when the timer reaches
3072 cycles of the 24.576-MHz clock (125 µs).
21
cycleMaster
RSCU
When bit 21 is set to 1, the PCI7410 device is root and it generates a cycle start packet every time
the cycle timer rolls over, based on the setting of bit 22 (cycleSource). When bit 21 is cleared, the
OHCI-Lynx accepts received cycle start packets to maintain synchronization with the node which
is sending them. Bit 21 is automatically cleared when bit 25 (cycleTooLong) in the interrupt event
register at OHCI offset 80h/84h (see Section 8.21) is set to 1. Bit 21 cannot be set to 1 until bit 25
(cycleTooLong) is cleared.
20
CycleTimerEnable
RSC
When bit 20 is set to 1, the cycle timer offset counts cycles of the 24.576-MHz clock and rolls over
at the appropriate time, based on the settings of the above bits. When this bit is cleared, the cycle
timer offset does not count.
19–11
RSVD
R
10
RcvPhyPkt
RSC
Reserved. Bits 19–11 return 0s when read.
When bit 10 is set to 1, the receiver accepts incoming PHY packets into the AR request context if
the AR request context is enabled. This bit does not control receipt of self-identification packets.
9
RcvSelfID
RSC
When bit 9 is set to 1, the receiver accepts incoming self-identification packets. Before setting this
bit to 1, software must ensure that the self-ID buffer pointer register contains a valid address.
8–7
RSVD
R
6‡
tag1SyncFilterLock
RS
5–0
RSVD
R
Reserved. Bits 8 and 7 return 0s when read.
When bit 6 is set to 1, bit 6 (tag1SyncFilter) in the isochronous receive context match register (see
Section 8.46) is set to 1 for all isochronous receive contexts. When bit 6 is cleared, bit 6
(tag1SyncFilter) in the isochronous receive context match register has read/write access. This bit is
cleared when GRST is asserted.
Reserved. Bits 5–0 return 0s when read.
‡ One or more bits in this register are cleared only by the assertion of GRST.
8–28
8.32 Node Identification Register
The node identification register contains the address of the node on which the OHCI-Lynx chip resides, and
indicates the valid node number status. The 16-bit combination of the busNumber field (bits 15–6) and the
NodeNumber field (bits 5–0) is referred to as the node ID. See Table 8–24 for a complete description of the register
contents.
Bit
31
30
29
28
27
26
25
Name
Type
24
23
22
21
20
19
18
17
16
Node identification
RU
RU
R
R
RU
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Node identification
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RU
RU
RU
RU
RU
RU
1
1
1
1
1
1
1
1
1
1
X
X
X
X
X
X
Register:
Offset:
Type:
Default:
Node identification
E8h
Read/Write/Update, Read/Update, Read-only
0000 FFXXh
Table 8–24. Node Identification Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31
iDValid
RU
Bit 31 indicates whether or not the PCI7410 device has a valid node number. It is cleared when a 1394
bus reset is detected and set to 1 when the PCI7410 device receives a new node number from its PHY
layer.
30
root
RU
Bit 30 is set to 1 during the bus reset process if the attached PHY layer is root.
29–28
RSVD
R
27
CPS
RU
26–16
RSVD
R
15–6
busNumber
RWU
This field identifies the specific 1394 bus the PCI7410 device belongs to when multiple
1394-compatible buses are connected via a bridge.
5–0
NodeNumber
RU
This field is the physical node number established by the PHY layer during self-identification. It is
automatically set to the value received from the PHY layer after the self-identification phase. If the PHY
layer sets the nodeNumber to 63, then software must not set bit 15 (run) in the asynchronous context
control register (see Section 8.40) for either of the AT DMA contexts.
Reserved. Bits 29 and 28 return 0s when read.
Bit 27 is set to 1 if the PHY layer is reporting that cable power status is OK.
Reserved. Bits 26–16 return 0s when read.
8–29
8.33 PHY Layer Control Register
The PHY layer control register reads from or writes to a PHY register. See Table 8–25 for a complete description of
the register contents.
Bit
31
30
29
28
27
26
25
Name
Type
24
23
22
21
20
19
18
17
16
PHY layer control
RU
R
R
R
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
RU
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
PHY layer control
RWU
RWU
R
R
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
PHY layer control
ECh
Read/Write/Update, Read/Write, Read/Update, Read-only
0000 0000h
Table 8–25. PHY Control Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31
rdDone
RU
Bit 31 is cleared to 0 by the PCI7410 device when either bit 15 (rdReg) or bit 14 (wrReg) is set to 1.
This bit is set to 1 when a register transfer is received from the PHY layer.
30–28
RSVD
R
27–24
rdAddr
RU
Reserved. Bits 30–28 return 0s when read.
This field is the address of the register most recently received from the PHY layer.
23–16
rdData
RU
This field is the contents of a PHY register that has been read.
15
rdReg
RWU
Bit 15 is set to 1 by software to initiate a read request to a PHY register, and is cleared by hardware
when the request has been sent. Bits 14 (wrReg) and 15 (rdReg) must not both be set to 1
simultaneously.
14
wrReg
RWU
Bit 14 is set to 1 by software to initiate a write request to a PHY register, and is cleared by hardware
when the request has been sent. Bits 14 (wrReg) and 15 (rdReg) must not both be set to 1
simultaneously.
13–12
RSVD
R
11–8
regAddr
RW
This field is the address of the PHY register to be written or read.
7–0
wrData
RW
This field is the data to be written to a PHY register and is ignored for reads.
8–30
Reserved. Bits 13 and 12 return 0s when read.
8.34 Isochronous Cycle Timer Register
The isochronous cycle timer register indicates the current cycle number and offset. When the PCI7410 device is cycle
master, this register is transmitted with the cycle start message. When the PCI7410 device is not cycle master, this
register is loaded with the data field in an incoming cycle start. In the event that the cycle start message is not received,
the fields can continue incrementing on their own (if programmed) to maintain a local time reference. See Table 8–26
for a complete description of the register contents.
Bit
31
30
29
28
27
26
Name
Type
25
24
23
22
21
20
19
18
17
16
Isochronous cycle timer
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
Default
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Isochronous cycle timer
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Register:
Offset:
Type:
Default:
Isochronous cycle timer
F0h
Read/Write/Update
XXXX XXXXh
Table 8–26. Isochronous Cycle Timer Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31–25
cycleSeconds
RWU
This field counts seconds [rollovers from bits 24–12 (cycleCount field)] modulo 128.
24–12
cycleCount
RWU
This field counts cycles [rollovers from bits 11–0 (cycleOffset field)] modulo 8000.
11–0
cycleOffset
RWU
This field counts 24.576-MHz clocks modulo 3072, that is, 125 µs. If an external 8-kHz clock
configuration is being used, then this field must be cleared to 0s at each tick of the external clock.
8–31
8.35 Asynchronous Request Filter High Register
The asynchronous request filter high set/clear register enables asynchronous receive requests on a per-node basis,
and handles the upper node IDs. When a packet is destined for either the physical request context or the ARRQ
context, the source node ID is examined. If the bit corresponding to the node ID is not set to 1 in this register, then
the packet is not acknowledged and the request is not queued. The node ID comparison is done if the source node
is on the same bus as the PCI7410 device. Nonlocal bus-sourced packets are not acknowledged unless bit 31 in this
register is set to 1. See Table 8–27 for a complete description of the register contents.
Bit
31
30
29
28
27
26
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
Default
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
Name
Type
Default
24
23
22
21
20
19
18
17
16
RSC
RSC
RSC
RSC
RSC
RSC
RSC
0
0
0
0
0
0
0
6
5
4
3
2
1
0
Asynchronous request filter high
Name
Type
25
Asynchronous request filter high
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Asynchronous request filter high
100h set register
104h clear register
Read/Set/Clear
0000 0000h
Table 8–27. Asynchronous Request Filter High Register Description
8–32
BIT
FIELD NAME
TYPE
DESCRIPTION
31
asynReqAllBuses
RSC
If bit 31 is set to 1, all asynchronous requests received by the PCI7410 device from nonlocal bus
nodes are accepted.
30
asynReqResource62
RSC
If bit 30 is set to 1 for local bus node number 62, asynchronous requests received by the PCI7410
device from that node are accepted.
29
asynReqResource61
RSC
If bit 29 is set to 1 for local bus node number 61, asynchronous requests received by the PCI7410
device from that node are accepted.
28
asynReqResource60
RSC
If bit 28 is set to 1 for local bus node number 60, asynchronous requests received by the PCI7410
device from that node are accepted.
27
asynReqResource59
RSC
If bit 27 is set to 1 for local bus node number 59, asynchronous requests received by the PCI7410
device from that node are accepted.
26
asynReqResource58
RSC
If bit 26 is set to 1 for local bus node number 58, asynchronous requests received by the PCI7410
device from that node are accepted.
25
asynReqResource57
RSC
If bit 25 is set to 1 for local bus node number 57, asynchronous requests received by the PCI7410
device from that node are accepted.
24
asynReqResource56
RSC
If bit 24 is set to 1 for local bus node number 56, asynchronous requests received by the PCI7410
device from that node are accepted.
23
asynReqResource55
RSC
If bit 23 is set to 1 for local bus node number 55, asynchronous requests received by the PCI7410
device from that node are accepted.
22
asynReqResource54
RSC
If bit 22 is set to 1 for local bus node number 54, asynchronous requests received by the PCI7410
device from that node are accepted.
21
asynReqResource53
RSC
If bit 21 is set to 1 for local bus node number 53, asynchronous requests received by the PCI7410
device from that node are accepted.
20
asynReqResource52
RSC
If bit 20 is set to 1 for local bus node number 52, asynchronous requests received by the PCI7410
device from that node are accepted.
19
asynReqResource51
RSC
If bit 19 is set to 1 for local bus node number 51, asynchronous requests received by the PCI7410
device from that node are accepted.
Table 8–27. Asynchronous Request Filter High Register Description (Continued)
BIT
FIELD NAME
TYPE
DESCRIPTION
18
asynReqResource50
RSC
If bit 18 is set to 1 for local bus node number 50, asynchronous requests received by the PCI7410
device from that node are accepted.
17
asynReqResource49
RSC
If bit 17 is set to 1 for local bus node number 49, asynchronous requests received by the PCI7410
device from that node are accepted.
16
asynReqResource48
RSC
If bit 16 is set to 1 for local bus node number 48, asynchronous requests received by the PCI7410
device from that node are accepted.
15
asynReqResource47
RSC
If bit 15 is set to 1 for local bus node number 47, asynchronous requests received by the PCI7410
device from that node are accepted.
14
asynReqResource46
RSC
If bit 14 is set to 1 for local bus node number 46, asynchronous requests received by the PCI7410
device from that node are accepted.
13
asynReqResource45
RSC
If bit 13 is set to 1 for local bus node number 45, asynchronous requests received by the PCI7410
device from that node are accepted.
12
asynReqResource44
RSC
If bit 12 is set to 1 for local bus node number 44, asynchronous requests received by the PCI7410
device from that node are accepted.
11
asynReqResource43
RSC
If bit 11 is set to 1 for local bus node number 43, asynchronous requests received by the PCI7410
device from that node are accepted.
10
asynReqResource42
RSC
If bit 10 is set to 1 for local bus node number 42, asynchronous requests received by the PCI7410
device from that node are accepted.
9
asynReqResource41
RSC
If bit 9 is set to 1 for local bus node number 41, asynchronous requests received by the PCI7410
device from that node are accepted.
8
asynReqResource40
RSC
If bit 8 is set to 1 for local bus node number 40, asynchronous requests received by the PCI7410
device from that node are accepted.
7
asynReqResource39
RSC
If bit 7 is set to 1 for local bus node number 39, asynchronous requests received by the PCI7410
device from that node are accepted.
6
asynReqResource38
RSC
If bit 6 is set to 1 for local bus node number 38, asynchronous requests received by the PCI7410
device from that node are accepted.
5
asynReqResource37
RSC
If bit 5 is set to 1 for local bus node number 37, asynchronous requests received by the PCI7410
device from that node are accepted.
4
asynReqResource36
RSC
If bit 4 is set to 1 for local bus node number 36, asynchronous requests received by the PCI7410
device from that node are accepted.
3
asynReqResource35
RSC
If bit 3 is set to 1 for local bus node number 35, asynchronous requests received by the PCI7410
device from that node are accepted.
2
asynReqResource34
RSC
If bit 2 is set to 1 for local bus node number 34, asynchronous requests received by the PCI7410
device from that node are accepted.
1
asynReqResource33
RSC
If bit 1 is set to 1 for local bus node number 33, asynchronous requests received by the PCI7410
device from that node are accepted.
0
asynReqResource32
RSC
If bit 0 is set to 1 for local bus node number 32, asynchronous requests received by the PCI7410
device from that node are accepted.
8–33
8.36 Asynchronous Request Filter Low Register
The asynchronous request filter low set/clear register enables asynchronous receive requests on a per-node basis,
and handles the lower node IDs. Other than filtering different node IDs, this register behaves identically to the
asynchronous request filter high register. See Table 8–28 for a complete description of the register contents.
Bit
31
30
29
28
27
26
Name
Type
25
24
23
22
21
20
19
18
17
16
Asynchronous request filter low
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Asynchronous request filter low
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Asynchronous request filter low
108h set register
10Ch clear register
Read/Set/Clear
0000 0000h
Table 8–28. Asynchronous Request Filter Low Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31
asynReqResource31
RSC
If bit 31 is set to 1 for local bus node number 31, asynchronous requests received by the PCI7410
device from that node are accepted.
30
asynReqResource30
RSC
If bit 30 is set to 1 for local bus node number 30, asynchronous requests received by the PCI7410
device from that node are accepted.
29–2
asynReqResourcen
RSC
Bits 29 through 2 (asynReqResourcen, where n = 29, 28, 27, …, 2) follow the same pattern as
bits 31 and 30.
1
asynReqResource1
RSC
If bit 1 is set to 1 for local bus node number 1, asynchronous requests received by the PCI7410
device from that node are accepted.
0
asynReqResource0
RSC
If bit 0 is set to 1 for local bus node number 0, asynchronous requests received by the PCI7410
device from that node are accepted.
8–34
8.37 Physical Request Filter High Register
The physical request filter high set/clear register enables physical receive requests on a per-node basis, and handles
the upper node IDs. When a packet is destined for the physical request context, and the node ID has been compared
against the ARRQ registers, then the comparison is done again with this register. If the bit corresponding to the node
ID is not set to 1 in this register, then the request is handled by the ARRQ context instead of the physical request
context. The node ID comparison is done if the source node is on the same bus as the PCI7410 device. Nonlocal
bus-sourced packets are not acknowledged unless bit 31 in this register is set to 1. See Table 8–29 for a complete
description of the register contents.
Bit
31
30
29
28
27
26
Name
Type
25
24
23
22
21
20
19
18
17
16
Physical request filter high
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Name
Type
Default
Physical request filter high
Register:
Offset:
Type:
Default:
Physical request filter high
110h set register
114h clear register
Read/Set/Clear
0000 0000h
Table 8–29. Physical Request Filter High Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31
physReqAllBusses
RSC
If bit 31 is set to 1, all asynchronous requests received by the PCI7410 device from nonlocal
bus nodes are accepted. Bit 31 is not cleared by a PRST.
30
physReqResource62
RSC
If bit 30 is set to 1 for local bus node number 62, physical requests received by the PCI7410
device from that node are handled through the physical request context.
29
physReqResource61
RSC
If bit 29 is set to 1 for local bus node number 61, physical requests received by the PCI7410
device from that node are handled through the physical request context.
28
physReqResource60
RSC
If bit 28 is set to 1 for local bus node number 60, physical requests received by the PCI7410
device from that node are handled through the physical request context.
27
physReqResource59
RSC
If bit 27 is set to 1 for local bus node number 59, physical requests received by the PCI7410
device from that node are handled through the physical request context.
26
physReqResource58
RSC
If bit 26 is set to 1 for local bus node number 58, physical requests received by the PCI7410
device from that node are handled through the physical request context.
25
physReqResource57
RSC
If bit 25 is set to 1 for local bus node number 57, physical requests received by the PCI7410
device from that node are handled through the physical request context.
24
physReqResource56
RSC
If bit 24 is set to 1 for local bus node number 56, physical requests received by the PCI7410
device from that node are handled through the physical request context.
23
physReqResource55
RSC
If bit 23 is set to 1 for local bus node number 55, physical requests received by the PCI7410
device from that node are handled through the physical request context.
22
physReqResource54
RSC
If bit 22 is set to 1 for local bus node number 54, physical requests received by the PCI7410
device from that node are handled through the physical request context.
21
physReqResource53
RSC
If bit 21 is set to 1 for local bus node number 53, physical requests received by the PCI7410
device from that node are handled through the physical request context.
20
physReqResource52
RSC
If bit 20 is set to 1 for local bus node number 52, physical requests received by the PCI7410
device from that node are handled through the physical request context.
19
physReqResource51
RSC
If bit 19 is set to 1 for local bus node number 51, physical requests received by the PCI7410
device from that node are handled through the physical request context.
8–35
Table 8–29. Physical Request Filter High Register Description (Continued)
8–36
BIT
FIELD NAME
TYPE
DESCRIPTION
18
physReqResource50
RSC
If bit 18 is set to 1 for local bus node number 50, physical requests received by the PCI7410
device from that node are handled through the physical request context.
17
physReqResource49
RSC
If bit 17 is set to 1 for local bus node number 49, physical requests received by the PCI7410
device from that node are handled through the physical request context.
16
physReqResource48
RSC
If bit 16 is set to 1 for local bus node number 48, physical requests received by the PCI7410
device from that node are handled through the physical request context.
15
physReqResource47
RSC
If bit 15 is set to 1 for local bus node number 47, physical requests received by the PCI7410
device from that node are handled through the physical request context.
14
physReqResource46
RSC
If bit 14 is set to 1 for local bus node number 46, physical requests received by the PCI7410
device from that node are handled through the physical request context.
13
physReqResource45
RSC
If bit 13 is set to 1 for local bus node number 45, physical requests received by the PCI7410
device from that node are handled through the physical request context.
12
physReqResource44
RSC
If bit 12 is set to 1 for local bus node number 44, physical requests received by the PCI7410
device from that node are handled through the physical request context.
11
physReqResource43
RSC
If bit 11 is set to 1 for local bus node number 43, physical requests received by the PCI7410
device from that node are handled through the physical request context.
10
physReqResource42
RSC
If bit 10 is set to 1 for local bus node number 42, physical requests received by the PCI7410
device from that node are handled through the physical request context.
9
physReqResource41
RSC
If bit 9 is set to 1 for local bus node number 41, physical requests received by the PCI7410
device from that node are handled through the physical request context.
8
physReqResource40
RSC
If bit 8 is set to 1 for local bus node number 40, physical requests received by the PCI7410
device from that node are handled through the physical request context.
7
physReqResource39
RSC
If bit 7 is set to 1 for local bus node number 39, physical requests received by the PCI7410
device from that node are handled through the physical request context.
6
physReqResource38
RSC
If bit 6 is set to 1 for local bus node number 38, physical requests received by the PCI7410
device from that node are handled through the physical request context.
5
physReqResource37
RSC
If bit 5 is set to 1 for local bus node number 37, physical requests received by the PCI7410
device from that node are handled through the physical request context.
4
physReqResource36
RSC
If bit 4 is set to 1 for local bus node number 36, physical requests received by the PCI7410
device from that node are handled through the physical request context.
3
physReqResource35
RSC
If bit 3 is set to 1 for local bus node number 35, physical requests received by the PCI7410
device from that node are handled through the physical request context.
2
physReqResource34
RSC
If bit 2 is set to 1 for local bus node number 34, physical requests received by the PCI7410
device from that node are handled through the physical request context.
1
physReqResource33
RSC
If bit 1 is set to 1 for local bus node number 33, physical requests received by the PCI7410
device from that node are handled through the physical request context.
0
physReqResource32
RSC
If bit 0 is set to 1 for local bus node number 32, physical requests received by the PCI7410
device from that node are handled through the physical request context.
8.38 Physical Request Filter Low Register
The physical request filter low set/clear register enables physical receive requests on a per-node basis, and handles
the lower node IDs. When a packet is destined for the physical request context, and the node ID has been compared
against the asynchronous request filter registers, then the node ID comparison is done again with this register. If the
bit corresponding to the node ID is not set to 1 in this register, then the request is handled by the asynchronous request
context instead of the physical request context. See Table 8–30 for a complete description of the register contents.
Bit
31
30
29
28
27
26
25
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
Default
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
Name
Type
Default
23
22
21
20
19
18
17
16
RSC
RSC
RSC
RSC
RSC
RSC
RSC
0
0
0
0
0
0
0
6
5
4
3
2
1
0
Physical request filter low
Name
Type
24
Physical request filter low
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Physical request filter low
118h set register
11Ch clear register
Read/Set/Clear
0000 0000h
Table 8–30. Physical Request Filter Low Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31
physReqResource31
RSC
If bit 31 is set to 1 for local bus node number 31, physical requests received by the PCI7410 device
from that node are handled through the physical request context.
30
physReqResource30
RSC
If bit 30 is set to 1 for local bus node number 30, physical requests received by the PCI7410 device
from that node are handled through the physical request context.
29–2
physReqResourcen
RSC
Bits 29 through 2 (physReqResourcen, where n = 29, 28, 27, …, 2) follow the same pattern as
bits 31 and 30.
1
physReqResource1
RSC
If bit 1 is set to 1 for local bus node number 1, physical requests received by the PCI7410 device
from that node are handled through the physical request context.
0
physReqResource0
RSC
If bit 0 is set to 1 for local bus node number 0, physical requests received by the PCI7410 device
from that node are handled through the physical request context.
8.39 Physical Upper Bound Register (Optional Register)
The physical upper bound register is an optional register and is not implemented. This register returns all 0s when
read.
Bit
31
30
29
28
27
26
25
Name
24
23
22
21
20
19
18
17
16
Physical upper bound
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Name
Physical upper bound
Register:
Offset:
Type:
Default:
Physical upper bound
120h
Read-only
0000 0000h
8–37
8.40 Asynchronous Context Control Register
The asynchronous context control set/clear register controls the state and indicates status of the DMA context. See
Table 8–31 for a complete description of the register contents.
Bit
31
30
29
28
27
26
Name
25
24
23
22
21
20
19
18
17
16
Asynchronous context control
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Asynchronous context control
RSCU
R
R
RSU
RU
RU
R
R
RU
RU
RU
RU
RU
RU
RU
RU
0
0
0
X
0
0
0
0
X
X
X
X
X
X
X
X
Register:
Offset:
Type:
Default:
Asynchronous context control
180h set register
[ATRQ]
184h clear register [ATRQ]
1A0h set register
[ATRS]
1A4h clear register [ATRS]
1C0h set register
[ARRQ]
1C4h clear register [ARRQ]
1E0h set register
[ARRS]
1E4h clear register [ARRS]
Read/Set/Clear/Update, Read/Set/Update, Read/Update, Read-only
0000 X0XXh
Table 8–31. Asynchronous Context Control Register Description
BIT
FIELD NAME
TYPE
31–16
RSVD
R
15
run
RSCU
14–13
RSVD
R
12
wake
RSU
Software sets bit 12 to 1 to cause the PCI7410 device to continue or resume descriptor processing.
The PCI7410 device clears this bit on every descriptor fetch.
11
dead
RU
The PCI7410 device sets bit 11 to 1 when it encounters a fatal error, and clears the bit when software
clears bit 15 (run). Asynchronous contexts supporting out-of-order pipelining provide unique
ContextControl.dead functionality. See Section 7.7 in the 1394 Open Host Controller Interface
Specification (Release 1.1) for more information.
The PCI7410 device sets bit 10 to 1 when it is processing descriptors.
10
active
RU
9–8
RSVD
R
7–5
spd
RU
DESCRIPTION
Reserved. Bits 31–16 return 0s when read.
Bit 15 is set to 1 by software to enable descriptor processing for the context and cleared by software
to stop descriptor processing. The PCI7410 device changes this bit only on a system (hardware) or
software reset.
Reserved. Bits 14 and 13 return 0s when read.
Reserved. Bits 9 and 8 return 0s when read.
This field indicates the speed at which a packet was received or transmitted and only contains
meaningful information for receive contexts. This field is encoded as:
000 = 100M bits/sec
001 = 200M bits/sec
010 = 400M bits/sec
All other values are reserved.
4–0
8–38
eventcode
RU
This field holds the acknowledge sent by the link core for this packet or an internally generated error
code if the packet was not transferred successfully.
8.41 Asynchronous Context Command Pointer Register
The asynchronous context command pointer register contains a pointer to the address of the first descriptor block
that the PCI7410 device accesses when software enables the context by setting bit 15 (run) in the asynchronous
context control register (see Section 8.40) to 1. See Table 8–32 for a complete description of the register contents.
Bit
31
30
29
28
27
Name
Type
26
25
24
23
22
21
20
19
18
17
16
Asynchronous context command pointer
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
Default
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Asynchronous context command pointer
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
RWU
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Register:
Offset:
Type:
Default:
Asynchronous context command pointer
18Ch [ATRQ]
1ACh [ATRS]
1CCh [ARRQ]
1ECh [ARRS]
Read/Write/Update
XXXX XXXXh
Table 8–32. Asynchronous Context Command Pointer Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31–4
descriptorAddress
RWU
Contains the upper 28 bits of the address of a 16-byte aligned descriptor block.
3–0
Z
RWU
Indicates the number of contiguous descriptors at the address pointed to by the descriptor address.
If Z is 0, then it indicates that the descriptorAddress field (bits 31–4) is not valid.
8–39
8.42 Isochronous Transmit Context Control Register
The isochronous transmit context control set/clear register controls options, state, and status for the isochronous
transmit DMA contexts. The n value in the following register addresses indicates the context number (n = 0, 1, 2, 3,
…, 7). See Table 8–33 for a complete description of the register contents.
Bit
31
30
29
28
27
26
Name
Type
25
24
23
22
21
20
19
18
17
16
Isochronous transmit context control
RSCU
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
RSC
Default
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RSC
R
R
RSU
RU
RU
R
R
RU
RU
RU
RU
RU
RU
RU
RU
0
0
0
X
0
0
0
0
X
X
X
X
X
X
X
X
Name
Type
Default
Isochronous transmit context control
Register:
Offset:
Type:
Default:
Isochronous transmit context control
200h + (16 * n)
set register
204h + (16 * n)
clear register
Read/Set/Clear/Update, Read/Set/Clear, Read/Set/Update, Read/Update, Read-only
XXXX X0XXh
Table 8–33. Isochronous Transmit Context Control Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31
cycleMatchEnable
RSCU
When bit 31 is set to 1, processing occurs such that the packet described by the context first
descriptor block is transmitted in the cycle whose number is specified in the cycleMatch field
(bits 30–16). The cycleMatch field (bits 30–16) must match the low-order two bits of cycleSeconds
and the 13-bit cycleCount field in the cycle start packet that is sent or received immediately before
isochronous transmission begins. Since the isochronous transmit DMA controller may work ahead,
the processing of the first descriptor block may begin slightly in advance of the actual cycle in which
the first packet is transmitted.
The effects of this bit, however, are impacted by the values of other bits in this register and are
explained in the 1394 Open Host Controller Interface Specification. Once the context has become
active, hardware clears this bit.
30–16
cycleMatch
RSC
This field contains a 15-bit value, corresponding to the low-order two bits of the isochronous cycle
timer register at OHCI offset F0h (see Section 8.34) cycleSeconds field (bits 31–25) and the
cycleCount field (bits 24–12). If bit 31 (cycleMatchEnable) is set to 1, then this isochronous transmit
DMA context becomes enabled for transmits when the low-order two bits of the isochronous cycle
timer register at OHCI offset F0h cycleSeconds field (bits 31–25) and the cycleCount field
(bits 24–12) value equal this field (cycleMatch) value.
15
run
RSC
Bit 15 is set to 1 by software to enable descriptor processing for the context and cleared by software
to stop descriptor processing. The PCI7410 device changes this bit only on a system (hardware) or
software reset.
14–13
RSVD
R
12
wake
RSU
Software sets bit 12 to 1 to cause the PCI7410 device to continue or resume descriptor processing.
The PCI7410 device clears this bit on every descriptor fetch.
11
dead
RU
The PCI7410 device sets bit 11 to 1 when it encounters a fatal error, and clears the bit when software
clears bit 15 (run) to 0.
10
active
RU
The PCI7410 device sets bit 10 to 1 when it is processing descriptors.
9–8
RSVD
R
7–5
spd
RU
This field in not meaningful for isochronous transmit contexts.
4–0
event code
RU
Following an OUTPUT_LAST* command, the error code is indicated in this field. Possible values are:
ack_complete, evt_descriptor_read, evt_data_read, and evt_unknown.
Reserved. Bits 14 and 13 return 0s when read.
Reserved. Bits 9 and 8 return 0s when read.
† On an overflow for each running context, the isochronous transmit DMA supports up to 7 cycle skips, when the following are true:
1. Bit 11 (dead) in either the isochronous transmit or receive context control register is set to 1.
2. Bits 4–0 (eventcode field) in either the isochronous transmit or receive context control register is set to evt_timeout.
3. Bit 24 (unrecoverableError) in the interrupt event register at OHCI offset 80h/84h (see Section 8.21) is set to 1.
8–40
8.43 Isochronous Transmit Context Command Pointer Register
The isochronous transmit context command pointer register contains a pointer to the address of the first descriptor
block that the PCI7410 device accesses when software enables an isochronous transmit context by setting bit 15
(run) in the isochronous transmit context control register (see Section 8.42) to 1. The isochronous transmit DMA
context command pointer can be read when a context is active. The n value in the following register addresses
indicates the context number (n = 0, 1, 2, 3, …, 7).
Bit
31
30
29
28
27
26
Name
Type
25
24
23
22
21
20
19
18
17
16
Isochronous transmit context command pointer
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Name
Isochronous transmit context command pointer
Register:
Offset:
Type:
Default:
Isochronous transmit context command pointer
20Ch + (16 * n)
Read-only
XXXX XXXXh
8.44 Isochronous Receive Context Control Register
The isochronous receive context control set/clear register controls options, state, and status for the isochronous
receive DMA contexts. The n value in the following register addresses indicates the context number (n = 0, 1, 2, 3).
See Table 8–34 for a complete description of the register contents.
Bit
31
30
29
28
27
26
Name
Type
25
24
23
22
21
20
19
18
17
16
Isochronous receive context control
RSC
RSC
RSCU
RSC
RSC
R
R
R
R
R
R
R
R
R
R
R
Default
X
X
X
X
X
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Isochronous receive context control
RSCU
R
R
RSU
RU
RU
R
R
RU
RU
RU
RU
RU
RU
RU
RU
0
0
0
X
0
0
0
0
X
X
X
X
X
X
X
X
Register:
Offset:
Isochronous receive context control
400h + (32 * n)
set register
404h + (32 * n)
clear register
Read/Set/Clear/Update, Read/Set/Clear, Read/Set/Update, Read/Update, Read-only
XX00 X0XXh
Type:
Default:
Table 8–34. Isochronous Receive Context Control Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31
bufferFill
RSC
When bit 31 is set to 1, received packets are placed back-to-back to completely fill each receive
buffer. When this bit is cleared, each received packet is placed in a single buffer. If bit 28
(multiChanMode) is set to 1, then this bit must also be set to 1. The value of this bit must not be
changed while bit 10 (active) or bit 15 (run) is set to 1.
30
isochHeader
RSC
When bit 30 is set to 1, received isochronous packets include the complete 4-byte isochronous
packet header seen by the link layer. The end of the packet is marked with a xferStatus in the first
doublet, and a 16-bit timeStamp indicating the time of the most recently received (or sent) cycleStart
packet.
When this bit is cleared, the packet header is stripped from received isochronous packets. The
packet header, if received, immediately precedes the packet payload. The value of this bit must not
be changed while bit 10 (active) or bit 15 (run) is set to 1.
8–41
Table 8–34. Isochronous Receive Context Control Register Description (Continued)
BIT
FIELD NAME
TYPE
DESCRIPTION
29
cycleMatchEnable
RSCU
When bit 29 is set to 1 and the 13-bit cycleMatch field (bits 24–12) in the isochronous receive context
match register (See Section 8.46) matches the 13-bit cycleCount field in the cycleStart packet, the
context begins running. The effects of this bit, however, are impacted by the values of other bits in
this register. Once the context has become active, hardware clears this bit. The value of this bit must
not be changed while bit 10 (active) or bit 15 (run) is set to 1.
28
multiChanMode
RSC
When bit 28 is set to 1, the corresponding isochronous receive DMA context receives packets for
all isochronous channels enabled in the isochronous receive channel mask high register at OHCI
offset 70h/74h (see Section 8.19) and isochronous receive channel mask low register at OHCI offset
78h/7Ch (see Section 8.20). The isochronous channel number specified in the isochronous receive
context match register (see Section 8.46) is ignored.
When this bit is cleared, the isochronous receive DMA context receives packets for the single
channel specified in the isochronous receive context match register (see Section 8.46). Only one
isochronous receive DMA context may use the isochronous receive channel mask registers (see
Sections 8.19, and 8.20). If more than one isochronous receive context control register has this bit
set, then the results are undefined. The value of this bit must not be changed while bit 10 (active)
or bit 15 (run) is set to 1.
27
dualBufferMode
RSC
When bit 27 is set to 1, receive packets are separated into first and second payload and streamed
independently to the firstBuffer series and secondBuffer series as described in Section 10.2.3 in the
1394 Open Host Controller Interface Specification. Also, when bit 27 is set to 1, both bits 28
(multiChanMode) and 31 (bufferFill) are cleared to 0. The value of this bit does not change when
either bit 10 (active) or bit 15 (run) is set to 1.
26–16
RSVD
R
15
run
RSCU
14–13
RSVD
R
12
wake
RSU
Software sets bit 12 to 1 to cause the PCI7410 device to continue or resume descriptor processing.
The PCI7410 device clears this bit on every descriptor fetch.
11
dead
RU
The PCI7410 device sets bit 11 to 1 when it encounters a fatal error, and clears the bit when software
clears bit 15 (run).
10
active
RU
The PCI7410 device sets bit 10 to 1 when it is processing descriptors.
9–8
RSVD
R
7–5
spd
RU
Reserved. Bits 26–16 return 0s when read.
Bit 15 is set to 1 by software to enable descriptor processing for the context and cleared by software
to stop descriptor processing. The PCI7410 device changes this bit only on a system (hardware)
or software reset.
Reserved. Bits 14 and 13 return 0s when read.
Reserved. Bits 9 and 8 return 0s when read.
This field indicates the speed at which the packet was received.
000 = 100M bits/sec
001 = 200M bits/sec
010 = 400M bits/sec
All other values are reserved.
4–0
8–42
event code
RU
For bufferFill mode, possible values are: ack_complete, evt_descriptor_read, evt_data_write, and
evt_unknown. Packets with data errors (either dataLength mismatches or dataCRC errors) and
packets for which a FIFO overrun occurred are backed out. For packet-per-buffer mode, possible
values are: ack_complete, ack_data_error, evt_long_packet, evt_overrun, evt_descriptor_read,
evt_data_write, and evt_unknown.
8.45 Isochronous Receive Context Command Pointer Register
The isochronous receive context command pointer register contains a pointer to the address of the first descriptor
block that the PCI7410 device accesses when software enables an isochronous receive context by setting bit 15 (run)
in the isochronous receive context control register (see Section 8.44) to 1. The n value in the following register
addresses indicates the context number (n = 0, 1, 2, 3).
Bit
31
30
29
28
27
Name
26
25
24
23
22
21
20
19
18
17
16
Isochronous receive context command pointer
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Isochronous receive context command pointer
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Register:
Offset:
Type:
Default:
Isochronous receive context command pointer
40Ch + (32 * n)
Read-only
XXXX XXXXh
8–43
8.46 Isochronous Receive Context Match Register
The isochronous receive context match register starts an isochronous receive context running on a specified cycle
number, filters incoming isochronous packets based on tag values, and waits for packets with a specified sync value.
The n value in the following register addresses indicates the context number (n = 0, 1, 2, 3). See Table 8–35 for a
complete description of the register contents.
Bit
31
30
29
28
27
26
Name
Type
25
24
23
22
21
20
19
18
17
16
Isochronous receive context match
RW
RW
RW
RW
R
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Default
X
X
X
X
0
0
0
X
X
X
X
X
X
X
X
X
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Isochronous receive context match
RW
RW
RW
RW
RW
RW
RW
RW
R
RW
RW
RW
RW
RW
RW
RW
X
X
X
X
X
X
X
X
0
X
X
X
X
X
X
X
Register:
Offset:
Type:
Default:
Isochronous receive context match
410Ch + (32 * n)
Read/Write, Read-only
XXXX XXXXh
Table 8–35. Isochronous Receive Context Match Register Description
BIT
FIELD NAME
TYPE
31
tag3
RW
If bit 31 is set to 1, this context matches on isochronous receive packets with a tag field of 11b.
30
tag2
RW
If bit 30 is set to 1, this context matches on isochronous receive packets with a tag field of 10b.
29
tag1
RW
If bit 29 is set to 1, this context matches on isochronous receive packets with a tag field of 01b.
28
tag0
RW
If bit 28 is set to 1, this context matches on isochronous receive packets with a tag field of 00b.
27
RSVD
R
26–12
cycleMatch
RW
This field contains a 15-bit value corresponding to the two low-order bits of cycleSeconds and the 13-bit
cycleCount field in the cycleStart packet. If cycleMatchEnable (bit 29) in the isochronous receive
context control register (see Section 8.44) is set to 1, then this context is enabled for receives when
the two low-order bits of the isochronous cycle timer register at OHCI offset F0h (see Section 8.34)
cycleSeconds field (bits 31–25) and cycleCount field (bits 24–12) value equal this field (cycleMatch)
value.
11–8
sync
RW
This 4-bit field is compared to the sync field of each isochronous packet for this channel when the
command descriptor w field is set to 11b.
7
RSVD
R
6
tag1SyncFilter
RW
DESCRIPTION
Reserved. Bit 27 returns 0 when read.
Reserved. Bit 7 returns 0 when read.
If bit 6 and bit 29 (tag1) are set to 1, then packets with tag 01b are accepted into the context if the two
most significant bits of the packet sync field are 00b. Packets with tag values other than 01b are filtered
according to bit 28 (tag0), bit 30 (tag2), and bit 31 (tag3) without any additional restrictions.
If this bit is cleared, then this context matches on isochronous receive packets as specified in
bits 28–31 (tag0–tag3) with no additional restrictions.
5–0
8–44
channelNumber
RW
This 6-bit field indicates the isochronous channel number for which this isochronous receive DMA
context accepts packets.
9 TI Extension Registers
The TI extension base address register provides a method of accessing memory-mapped TI extension registers. See
Section 7.9, TI Extension Base Address Register, for register bit field details. See Table 9–1 for the TI extension
register listing.
Table 9–1. TI Extension Register Map
REGISTER NAME
OFFSET
Reserved
00h–A7Fh
Isochronous Receive DV Enhancement Set
A80h
Isochronous Receive DV Enhancement Clear
A84h
Link Enhancement Control Set
A88h
Link Enhancement Control Clear
A8Ch
Isochronous Transmit Context 0 Timestamp Offset
A90h
Isochronous Transmit Context 1 Timestamp Offset
A94h
Isochronous Transmit Context 2 Timestamp Offset
A98h
Isochronous Transmit Context 3 Timestamp Offset
A9Ch
Isochronous Transmit Context 4 Timestamp Offset
AA0h
Isochronous Transmit Context 5 Timestamp Offset
AA4h
Isochronous Transmit Context 6 Timestamp Offset
AA8h
Isochronous Transmit Context 7 Timestamp Offset
AA8h
9.1 DV and MPEG2 Timestamp Enhancements
The DV timestamp enhancements are enabled by bit 8 (enab_dv_ts) in the link enhancement control register located
at PCI offset F4h and are aliased in TI extension register space at offset A88h (set) and A8Ch (clear).
The DV and MPEG transmit enhancements are enabled separately by bits in the link enhancement control register
located in PCI configuration space at PCI offset F4h. The link enhancement control register is also aliased as a
set/clear register in TI extension space at offset A88h (set) and A8Ch (clear).
Bit 8 (enab_dv_ts) of the link enhancement control register enables DV timestamp support. When enabled, the link
calculates a timestamp based on the cycle timer and the timestamp offset register and substitutes it in the SYT field
of the CIP once per DV frame.
Bit 10 (enab_mpeg_ts) of the link enhancement control register enables MPEG timestamp support. Two MPEG time
stamp modes are supported. The default mode calculates an initial delta that is added to the calculated timestamp
in addition to a user-defined offset. The initial offset is calculated as the difference in the intended transmit cycle count
and the cycle count field of the timestamp in the first TSP of the MPEG2 stream. The use of the initial delta can be
controlled by bit 31 (DisableInitialOffset) in the timestamp offset register (see Section 9.5).
The MPEG2 timestamp enhancements are enabled by bit 10 (enab_mpeg_ts) in the link enhancement control
register located at PCI offset F4h and aliased in TI extension register space at offset A88h (set) and A8Ch (clear).
When bit 10 (enab_mpeg_ts) is set to 1, the hardware applies the timestamp enhancements to isochronous transmit
packets that have the tag field equal to 01b in the isochronous packet header and a FMT field equal to 10h.
9–1
9.2 Isochronous Receive Digital Video Enhancements
The DV frame sync and branch enhancement provides a mechanism in buffer-fill mode to synchronize 1394 DV data
that is received in the correct order to DV frame-sized data buffers described by several INPUT_MORE descriptors
(see 1394 Open Host Controller Interface Specification, Release 1.1). This is accomplished by waiting for the
start-of-frame packet in a DV stream before transferring the received isochronous stream into the memory buffer
described by the INPUT_MORE descriptors. This can improve the DV capture application performance by reducing
the amount of processing overhead required to strip the CIP header and copy the received packets into frame-sized
buffers.
The start of a DV frame is represented in the 1394 packet as a 16-bit pattern of 1FX7h (first byte 1Fh and second
byte X7h) received as the first two bytes of the third quadlet in a DV isochronous packet.
9.3 Isochronous Receive Digital Video Enhancements Register
The isochronous receive digital video enhancements register enables the DV enhancements in the PCI7410 device.
The bits in this register may only be modified when both the active (bit 10) and run (bit 15) bits of the corresponding
context control register are 0. See Table 9–2 for a complete description of the register contents.
Bit
31
30
29
28
27
Type
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
Name
26
25
24
23
22
21
20
19
18
17
16
R
R
R
R
R
R
0
0
0
0
0
0
5
4
3
2
1
0
Isochronous receive digital video enhancements
Name
Isochronous receive digital video enhancements
Type
R
R
RSC
RSC
R
R
RSC
RSC
R
R
RSC
RSC
R
R
RSC
RSC
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Isochronous receive digital video enhancements
A80h
set register
A84h
clear register
Read/Set/Clear, Read-only
0000 0000h
Table 9–2. Isochronous Receive Digital Video Enhancements Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31–14
RSVD
R
13
DV_Branch3
RSC
Reserved. Bits 31–14 return 0s when read.
When bit 13 is set to 1, the isochronous receive context 3 synchronizes reception to the DV frame start
tag in bufferfill mode if input_more.b = 01b, and jumps to the descriptor pointed to by frameBranch if
a DV frame start tag is received out of place. This bit is only interpreted when bit 12 (CIP_Strip3) is
set to 1 and bit 30 (isochHeader) in the isochronous receive context control register at OHCI offset
460h/464h (see Section 8.44) is cleared to 0.
12
CIP_Strip3
RSC
When bit 12 is set to 1, the isochronous receive context 3 strips the first two quadlets of payload. This
bit is only interpreted when bit 30 (isochHeader) in the isochronous receive context control register at
OHCI offset 460h/464h (see Section 8.44) is cleared to 0.
11–10
RSVD
R
9
DV_Branch2
RSC
When bit 9 is set to 1, the isochronous receive context 2 synchronizes reception to the DV frame start
tag in bufferfill mode if input_more.b = 01b, and jumps to the descriptor pointed to by frameBranch if
a DV frame start tag is received out of place. This bit is only interpreted when bit 8 (CIP_Strip2) is set
to 1 and bit 30 (isochHeader) in the isochronous receive context control register at OHCI offset
440h/444h (see Section 8.44) is cleared to 0.
8
CIP_Strip2
RSC
When bit 8 is set to 1, the isochronous receive context 2 strips the first two quadlets of payload. This
bit is only interpreted when bit 30 (isochHeader) in the isochronous receive context control register at
OHCI offset 440h/444h (see Section 8.44) is cleared to 0.
9–2
Reserved. Bits 11 and 10 return 0s when read.
Table 9–2. Isochronous Receive Digital Video Enhancements Register Description (Continued)
BIT
FIELD NAME
TYPE
7–6
RSVD
R
DESCRIPTION
5
DV_Branch1
RSC
When bit 5 is set to 1, the isochronous receive context 1 synchronizes reception to the DV frame start
tag in bufferfill mode if input_more.b = 01b, and jumps to the descriptor pointed to by frameBranch if
a DV frame start tag is received out of place. This bit is only interpreted when bit 4 (CIP_Strip1) is set
to 1 and bit 30 (isochHeader) in the isochronous receive context control register at OHCI offset
420h/424h (see Section 8.44) is cleared to 0.
4
CIP_Strip1
RSC
When bit 4 is set to 1, the isochronous receive context 1 strips the first two quadlets of payload. This
bit is only interpreted when bit 30 (isochHeader) in the isochronous receive context control register at
OHCI offset 420h/424h (see Section 8.44) is cleared to 0.
3–2
RSVD
R
1
DV_Branch0
RSC
When bit 1 is set to 1, the isochronous receive context 0 synchronizes reception to the DV frame start
tag in bufferfill mode if input_more.b = 01b and jumps to the descriptor pointed to by frameBranch if
a DV frame start tag is received out of place. This bit is only interpreted when bit 0 (CIP_Strip0) is set
to 1 and bit 30 (isochHeader) in the isochronous receive context control register at OHCI offset
400h/404h (see Section 8.44) is cleared to 0.
0
CIP_Strip0
RSC
When bit 0 is set to 1, the isochronous receive context 0 strips the first two quadlets of payload. This
bit is only interpreted when bit 30 (isochHeader) in the isochronous receive context control register at
OHCI offset 400h/404h (see Section 8.44) is cleared to 0.
Reserved. Bits 7 and 6 return 0s when read.
Reserved. Bits 3 and 2 return 0s when read.
9–3
9.4 Link Enhancement Register
This register is a memory-mapped set/clear register that is an alias of the link enhancement control register at PCI
offset F4h. These bits may be initialized by software. Some of the bits may also be initialized by a serial EEPROM,
if one is present, as noted in the bit descriptions below. If the bits are to be initialized by software, then the bits must
be initialized prior to setting bit 19 (LPS) in the host controller control register at OHCI offset 50h/54h (see
Section 8.16). See Table 9–3 for a complete description of the register contents.
Bit
31
30
29
28
27
26
25
Name
24
23
22
21
20
19
18
17
16
Link enhancement
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Link enhancement
RSC
R
RSC
RSC
R
RSC
R
RSC
RSC
R
R
R
R
R
RSC
R
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Link enhancement
A88h
set register
A8Ch
clear register
Read/Set/Clear, Read-only
0000 0000h
Table 9–3. Link Enhancement Register Description
BIT
FIELD NAME
TYPE
31–16
RSVD
R
15
dis_at_pipeline
RSC
14
RSVD
R
13–12
atx_thresh
RSC
DESCRIPTION
Reserved. Bits 31–16 return 0s when read.
Disable AT pipelining. When bit 15 is set to 1, out-of-order AT pipelining is disabled.
Reserved.
This field sets the initial AT threshold value, which is used until the AT FIFO is underrun. When the
PCI7410 device retries the packet, it uses a 2K-byte threshold, resulting in a store-and-forward
operation.
00 = Threshold ~ 2K bytes resulting in a store-and-forward operation
01 = Threshold ~ 1.7K bytes (default)
10 = Threshold ~ 1K bytes
11 = Threshold ~ 512 bytes
These bits fine-tune the asynchronous transmit threshold. For most applications the 1.7K-byte
threshold is optimal. Changing this value may increase or decrease the 1394 latency depending on
the average PCI bus latency.
Setting the AT threshold to 1.7K, 1K, or 512 bytes results in data being transmitted at these thresholds
or when an entire packet has been checked into the FIFO. If the packet to be transmitted is larger
than the AT threshold, then the remaining data must be received before the AT FIFO is emptied;
otherwise, an underrun condition occurs, resulting in a packet error at the receiving node. As a result,
the link then commences store-and-forward operation. Wait until it has the complete packet in the
FIFO before retransmitting it on the second attempt, to ensure delivery.
An AT threshold of 2K results in store-and-forward operation, which means that asynchronous data
will not be transmitted until an end-of-packet token is received. Restated, setting the AT threshold
to 2K results in only complete packets being transmitted.
Note that this device always uses store-and-forward when the asynchronous transmit retries register
at OHCI offset 08h (see Section 8.3) is cleared.
9–4
11
RSVD
R
10
enab_mpeg_ts
RSC
9
RSVD
R
8
enab_dv_ts
RSC
Reserved. Bit 11 returns 0 when read.
Enable MPEG timestamp enhancements. When bit 10 is set to 1, the enhancement is enabled for
MPEG transmit streams (FMT = 20h).
Reserved. Bit 9 returns 0 when read.
Enable DV CIP timestamp enhancement. When bit 8 is set to 1, the enhancement is enabled for DV
CIP transmit streams (FMT = 00h).
Table 9–3. Link Enhancement Register Description (Continued)
BIT
FIELD NAME
TYPE
DESCRIPTION
7
enab_unfair
RSC
Enable asynchronous priority requests. OHCI-Lynx compatible. Setting bit 7 to 1 enables the link
to respond to requests with priority arbitration. It is recommended that this bit be set to 1.
6
RSVD
R
This bit is not assigned in the PCI7410 follow-on products, since this bit location loaded by the serial
EEPROM from the enhancements field corresponds to bit 23 (programPhyEnable) in the host
controller control register at OHCI offset 50h/54h (see Section 8.16).
5–2
RSVD
R
Reserved. Bits 5–2 return 0s when read.
1
enab_accel
RSC
0
RSVD
R
Enable acceleration enhancements. OHCI-Lynx compatible. When bit 1 is set to 1, the PHY layer
is notified that the link supports the IEEE Std 1394a-2000 acceleration enhancements, that is,
ack-accelerated, fly-by concatenation, etc. It is recommended that this bit be set to 1.
Reserved. Bit 0 returns 0 when read.
9.5 Timestamp Offset Register
The value of this register is added as an offset to the cycle timer value when using the MPEG, DV, and CIP
enhancements. A timestamp offset register is implemented per isochronous transmit context. The n value following
the offset indicates the context number (n = 0, 1, 2, 3, …, 7). These registers are programmed by software as
appropriate. See Table 9–4 for a complete description of the register contents.
Bit
31
30
29
28
27
26
25
Name
Type
24
23
22
21
20
19
18
17
16
Timestamp offset
RW
R
R
R
R
R
R
RW
RW
RW
RW
RW
RW
RW
RW
RW
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Timestamp offset
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Timestamp offset
A90h + (4*n)
Read/Write, Read-only
0000 0000h
Table 9–4. Timestamp Offset Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31
DisableInitialOffset
RW
Bit 31 disables the use of the initial timestamp offset when the MPEG2 enhancements are enabled.
A value of 0 indicates the use of the initial offset, a value of 1 indicates that the initial offset must not
be applied to the calculated timestamp. This bit has no meaning for the DV timestamp
enhancements.
30–25
RSVD
R
24–12
CycleCount
RW
Reserved. Bits 30–25 return 0s when read.
This field adds an offset to the cycle count field in the timestamp when the DV or MPEG2
enhancements are enabled. The cycle count field is incremented modulo 8000; therefore, values in
this field must be limited between 0 and 7999.
11–0
CycleOffset
RW
This field adds an offset to the cycle offset field in the timestamp when the DV or MPEG2
enhancements are enabled. The cycle offset field is incremented modulo 3072; therefore, values in
this field must be limited between 0 and 3071.
9–5
9–6
10 PHY Register Configuration
There are 16 accessible internal registers in the PCI7410 device. The configuration of the registers at addresses 0h
through 7h (the base registers) is fixed, whereas the configuration of the registers at addresses 8h through Fh (the
paged registers) is dependent upon which one of eight pages, numbered 0h through 7h, is currently selected. The
selected page is set in base register 7h.
10.1 Base Registers
Table 10–1 shows the configuration of the base registers, and Table 10–2 shows the corresponding field descriptions.
The base register field definitions are unaffected by the selected page number.
A reserved register or register field (marked as Reserved in the following register configuration tables) is read as 0,
but is subject to future usage. All registers in address pages 2 through 6 are reserved.
Table 10–1. Base Register Configuration
BIT POSITION
ADDRESS
0
1
0000
0001
2
3
4
5
Physical ID
RHB
IBR
6
7
R
CPS
Gap_Count
0010
Extended (111b)
Reserved
Total_Ports (0010b)
0011
Max_Speed (010b)
Reserved
Delay (0000b)
Jitter (000b)
0100
LCtrl
C
0101
Watchdog
ISBR
0110
0111
Loop
Pwr_fail
Pwr_Class
Timeout
Port_event
Enab_accel
Enab_multi
Reserved
Page_Select
Reserved
Port_Select
10–1
Table 10–2. Base Register Field Descriptions
FIELD
SIZE
TYPE
DESCRIPTION
Physical ID
6
R
This field contains the physical address ID of this node determined during self-ID. The physical ID is invalid
after a bus reset until self-ID has completed as indicated by an unsolicited register-0 status transfer.
R
1
R
Root. This bit indicates that this node is the root node. The R bit is cleared to 0 by bus reset and is set to 1
during tree-ID if this node becomes root.
CPS
1
R
Cable-power-status. This bit indicates the state of the CPS input terminal. The CPS terminal is normally tied
to serial bus cable power through a 400-kΩ resistor. A 0 in this bit indicates that the cable power voltage has
dropped below its threshold for ensured reliable operation.
RHB
1
R/W
Root-holdoff bit. This bit instructs the PHY layer to attempt to become root after the next bus reset. The RHB
bit is cleared to 0 by a system (hardware) reset and is unaffected by a bus reset.
IBR
1
R/W
Initiate bus reset. This bit instructs the PHY layer to initiate a long (166 µs) bus reset at the next opportunity.
Any receive or transmit operation in progress when this bit is set completes before the bus reset is initiated.
The IBR bit is cleared to 0 after a system (hardware) reset or a bus reset.
Gap_Count
6
R/W
Arbitration gap count. This value sets the subaction (fair) gap, arb-reset gap, and arb-delay times. The gap
count can be set either by a write to the register, or by reception or transmission of a PHY_CONFIG packet.
The gap count is reset to 3Fh by system (hardware) reset or after two consecutive bus resets without an
intervening write to the gap count register (either by a write to the PHY register or by a PHY_CONFIG
packet).
Extended
3
R
Extended register definition. For the PCI7410 device, this field is 111b, indicating that the extended register
set is implemented.
Total_Ports
4
R
Number of ports. This field indicates the number of ports implemented in the PHY layer. For the PCI7410
device this field is 2.
Max_Speed
3
R
PHY speed capability. For the PCI7410 PHY layer this field is 010b, indicating S400 speed capability.
Delay
4
R
PHY repeater data delay. This field indicates the worst case repeater data delay of the PHY layer, expressed
as 144+(delay × 20) ns. For the PCI7410 device this field is 0.
LCtrl
1
R/W
Link-active status control. This bit controls the active status of the LLC as indicated during self-ID. The
logical AND of this bit and the LPS active status is replicated in the L field (bit 9) of the self-ID packet. The LLC
is considered active only if both the LPS input is active and the LCtrl bit is set.
The LCtrl bit provides a software controllable means to indicate the LLC active/status in lieu of using the LPS
input.
The LCtrl bit is set to 1 by a system (hardware) reset and is unaffected by a bus reset.
NOTE: The state of the PHY-LLC interface is controlled solely by the LPS input, regardless of the state of the
LCtrl bit. If the PHY-LLC interface is operational as determined by the LPS input being active, received
packets and status information continue to be presented on the interface, and any requests indicated on the
LREQ input are processed, even if the LCtrl bit is cleared to 0.
C
1
R/W
Contender status. This bit indicates that this node is a contender for the bus or isochronous resource
manager. This bit is replicated in the c field (bit 20) of the self-ID packet.
Jitter
3
R
PHY repeater jitter. This field indicates the worst case difference between the fastest and slowest repeater
data delay, expressed as (Jitter+1) × 20 ns. For the PCI7410 device, this field is 0.
Pwr_Class
3
R/W
Node power class. This field indicates this node power consumption and source characteristics and is
replicated in the pwr field (bits 21–23) of the self-ID packet. This field is reset to the state specified by the
PC0–PC2 input terminals upon a system (hardware) reset and is unaffected by a bus reset. See Table 10–9.
Watchdog
1
R/W
Watchdog enable. This bit, if set to 1, enables the port event interrupt (Port_event) bit to be set whenever
resume operations begin on any port. This bit is cleared to 0 by system (hardware) reset and is unaffected by
bus reset.
10–2
Table 10–2. Base Register Field Descriptions (Continued)
FIELD
ISBR
SIZE
TYPE
DESCRIPTION
1
R/W
Initiate short arbitrated bus reset. This bit, if set to 1, instructs the PHY layer to initiate a short (1.3 µs)
arbitrated bus reset at the next opportunity. This bit is cleared to 0 by a bus reset.
NOTE: Legacy IEEE Std 1394-1995 compliant PHY layers can not be capable of performing short bus
resets. Therefore, initiation of a short bus reset in a network that contains such a legacy device results in a
long bus reset being performed.
Loop
1
R/W
Loop detect. This bit is set to 1 when the arbitration controller times out during tree-ID start and may indicate
that the bus is configured in a loop. This bit is cleared to 0 by system (hardware) reset or by writing a 1 to this
register bit.
If the Loop and Watchdog bits are both set and the LLC is or becomes inactive, the PHY layer activates the
LLC to service the interrupt.
NOTE: If the network is configured in a loop, only those nodes which are part of the loop generate a
configuration-timeout interrupt. All other nodes instead time out waiting for the tree-ID and/or self-ID process
to complete and then generate a state time-out interrupt and bus-reset.
Pwr_fail
1
R/W
Cable power failure detect. This bit is set to 1 whenever the CPS input transitions from high to low indicating
that cable power may be too low for reliable operation. This bit is cleared to 0 by system (hardware) reset or
by writing a 1 to this register bit.
Timeout
1
R/W
State time-out interrupt. This bit indicates that a state time-out has occurred (which also causes a bus reset
to occur). This bit is cleared to 0 by system (hardware) reset or by writing a 1 to this register bit.
Port_event
1
R/W
Port event detect. This bit is set to 1 upon a change in the bias (unless disabled) connected, disabled, or fault
bits for any port for which the port interrupt enable (Int_enable) bit is set. Additionally, if the Watchdog bit is
set, the Port_event bit is set to 1 at the start of resume operations on any port. This bit is cleared to 0 by
system (hardware) reset or by writing a 1 to this register bit.
Enab_accel
1
R/W
Enable accelerated arbitration. This bit enables the PHY layer to perform the various arbitration acceleration
enhancements defined in IEEE Std 1394a-2000 (ACK-accelerated arbitration, asynchronous fly-by
concatenation, and isochronous fly-by concatenation). This bit is cleared to 0 by system (hardware) reset
and is unaffected by bus reset.
Enab_multi
1
R/W
Enable multispeed concatenated packets. This bit enables the PHY layer to transmit concatenated packets
of differing speeds in accordance with the protocols defined in IEEE Std 1394a-2000. This bit is cleared to 0
by system (hardware) reset and is unaffected by bus reset.
Page_Select
3
R/W
Page_Select. This field selects the register page to use when accessing register addresses 8 through 15.
This field is cleared to 0 by a system (hardware) reset and is unaffected by bus reset.
Port_Select
4
R/W
Port_Select. This field selects the port when accessing per-port status or control (for example, when one of
the port status/control registers is accessed in page 0). Ports are numbered starting at 0. This field is cleared
to 0 by system (hardware) reset and is unaffected by bus reset.
10–3
10.2 Port Status Register
The port status page provides access to configuration and status information for each of the ports. The port is selected
by writing 0 to the Page_Select field and the desired port number to the Port_Select field in base register 7. Table 10–3
shows the configuration of the port status page registers and Table 10–4 shows the corresponding field descriptions.
If the selected port is not implemented, all registers in the port status page are read as 0.
Table 10–3. Page 0 (Port Status) Register Configuration
BIT POSITION
ADDRESS
0
1
1000
AStat
1001
Peer_Speed
2
3
4
5
Ch
Con
Int_enable
Fault
BStat
1010
Reserved
1011
Reserved
1100
Reserved
1101
Reserved
1110
Reserved
1111
Reserved
6
7
Bias
Dis
Reserved
Table 10–4. Page 0 (Port Status) Register Field Descriptions
FIELD
SIZE
TYPE
DESCRIPTION
AStat
2
R
TPA line state. This field indicates the TPA line state of the selected port, encoded as follows:
Code
Arb Value
11
Z
10
0
01
1
00
invalid
BStat
2
R
TPB line state. This field indicates the TPB line state of the selected port. This field has the same encoding as
the AStat field.
Ch
1
R
Child/parent status. A 1 indicates that the selected port is a child port. A 0 indicates that the selected port is
the parent port. A disconnected, disabled, or suspended port is reported as a child port. The Ch bit is invalid
after a bus reset until tree-ID has completed.
Con
1
R
Debounced port connection status. This bit indicates that the selected port is connected. The connection
must be stable for the debounce time of approximately 341 ms for the Con bit to be set to 1. The Con bit is
cleared to 0 by system (hardware) reset and is unaffected by bus reset.
NOTE: The Con bit indicates that the port is physically connected to a peer PHY device, but the port is not
necessarily active.
Bias
1
R
Debounced incoming cable bias status. A 1 indicates that the selected port is detecting incoming cable bias.
The incoming cable bias must be stable for the debounce time of 52 µs for the Bias bit to be set to 1.
Dis
1
RW
Port disabled control. If the Dis bit is set to 1, the selected port is disabled. The Dis bit is cleared to 0 by
system (hardware) reset (all ports are enabled for normal operation following system (hardware) reset). The
Dis bit is not affected by bus reset.
Peer_Speed
3
R
Port peer speed. This field indicates the highest speed capability of the peer PHY device connected to the
selected port, encoded as follows:
Code
Peer Speed
000
S100
001
S200
010
S400
011–111
invalid
The Peer_Speed field is invalid after a bus reset until self-ID has completed.
NOTE: Peer speed codes higher than 010b (S400) are defined in IEEE Std 1394a-2000. However, the
PCI7410 device is only capable of detecting peer speeds up to S400.
10–4
Table 10–4. Page 0 (Port Status) Register Field Descriptions (Continued)
FIELD
SIZE
TYPE
DESCRIPTION
Int_enable
1
RW
Port event interrupt enable. When the Int_enable bit is set to 1, a port event on the selected port sets the port
event interrupt (Port_event) bit and notifies the link. This bit is cleared to 0 by a system (hardware) reset and
is unaffected by bus reset.
Fault
1
RW
Fault. This bit indicates that a resume-fault or suspend-fault has occurred on the selected port, and that the
port is in the suspended state. A resume-fault occurs when a resuming port fails to detect incoming cable
bias from its attached peer. A suspend-fault occurs when a suspending port continues to detect incoming
cable bias from its attached peer. Writing 1 to this bit clears the fault bit to 0. This bit is cleared to 0 by system
(hardware) reset and is unaffected by bus reset.
10.3 Vendor Identification Register
The vendor identification page identifies the vendor/manufacturer and compliance level. The page is selected by
writing 1 to the Page_Select field in base register 7. Table 10–5 shows the configuration of the vendor identification
page, and Table 10–6 shows the corresponding field descriptions.
Table 10–5. Page 1 (Vendor ID) Register Configuration
BIT POSITION
ADDRESS
0
1
2
3
4
1000
Compliance
1001
Reserved
1010
Vendor_ID[0]
1011
Vendor_ID[1]
1100
Vendor_ID[2]
1101
Product_ID[0]
1110
Product_ID[1]
1111
Product_ID[2]
5
6
7
Table 10–6. Page 1 (Vendor ID) Register Field Descriptions
FIELD
SIZE
TYPE
DESCRIPTION
Compliance
8
R
Compliance level. For the PCI7410 device this field is 01h, indicating compliance with IEEE Std 1394a-2000.
Vendor_ID
24
R
Manufacturer’s organizationally unique identifier (OUI). For the PCI7410 device this field is 08 0028h (Texas
Instruments) (the MSB is at register address 1010b).
Product_ID
24
R
Product identifier. For the PCI7410 device this field is 42 4499h (the MSB is at register address 1101b).
10–5
10.4 Vendor-Dependent Register
The vendor-dependent page provides access to the special control features of the PCI7410 device, as well as to
configuration and status information used in manufacturing test and debug. This page is selected by writing 7 to the
Page_Select field in base register 7. Table 10–7 shows the configuration of the vendor-dependent page, and
Table 10–8 shows the corresponding field descriptions.
Table 10–7. Page 7 (Vendor-Dependent) Register Configuration
BIT POSITION
ADDRESS
0
1000
NPA
1
2
3
4
Reserved
5
6
7
Link_Speed
1001
Reserved for test
1010
Reserved for test
1011
Reserved for test
1100
Reserved for test
1101
Reserved for test
1110
Reserved for test
1111
Reserved for test
Table 10–8. Page 7 (Vendor-Dependent) Register Field Descriptions
FIELD
SIZE
TYPE
DESCRIPTION
NPA
1
RW
Null-packet actions flag. This bit instructs the PHY layer to not clear fair and priority requests when a null
packet is received with arbitration acceleration enabled. If this bit is set to 1, fair and priority requests are
cleared only when a packet of more than 8 bits is received; ACK packets (exactly 8 data bits), null packets
(no data bits), and malformed packets (less than 8 data bits) do not clear fair and priority requests. If this bit is
cleared to 0, fair and priority requests are cleared when any non-ACK packet is received, including null
packets or malformed packets of less than 8 bits. This bit is cleared to 0 by system (hardware) reset and is
unaffected by bus reset.
Link_Speed
2
RW
Link speed. This field indicates the top speed capability of the attached LLC. Encoding is as follows:
Code
Speed
00
S100
01
S200
10
S400
11
illegal
This field is replicated in the sp field of the self-ID packet to indicate the speed capability of the node (PHY
and LLC in combination). However, this field does not affect the PHY speed capability indicated to peer
PHYs during self-ID; the PCI7410 PHY layer identifies itself as S400 capable to its peers regardless of the
value in this field. This field is set to 10b (S400) by system (hardware) reset and is unaffected by bus reset.
10–6
10.5 Power-Class Programming
The PC0–PC2 terminals are programmed to set the default value of the power-class indicated in the pwr field
(bits 21–23) of the transmitted self-ID packet. Table 10–9 shows the descriptions of the various power classes. The
default power-class value is loaded following a system (hardware) reset, but is overridden by any value subsequently
loaded into the Pwr_Class field in register 4.
Table 10–9. Power Class Descriptions
PC0–PC2
DESCRIPTION
000
Node does not need power and does not repeat power.
001
Node is self-powered and provides a minimum of 15 W to the bus.
010
Node is self-powered and provides a minimum of 30 W to the bus.
011
Node is self-powered and provides a minimum of 45 W to the bus.
100
Node may be powered from the bus and is using up to 3 W. No additional power is needed to enable the link.
101
Reserved
110
Node is powered from the bus and uses up to 3 W. An additional 3 W is needed to enable the link.
111
Node is powered from the bus and uses up to 3 W. An additional 7 W is needed to enable the link.
10–7
10–8
11 PCI Firmware Loading Function Programming Model (Function 3)
The PCI7410 is a multifunction PCI device. Function 3 is provided so that the firmware can be loaded into internal
program memory. The configuration header is compliant with the PCI Local Bus Specification as a standard header.
Table 11–1 illustrates the PCI configuration header for function 3.
Table 11–1. Function 3 Configuration Register Map
REGISTER NAME
OFFSET
Device ID
Vendor ID
Status
00h
Command
Class code
BIST
Header type
Latency timer
04h
Revision ID
08h
Cache line size
0Ch
Base address register
10h
Reserved
14h–28h
Subsystem ID
Subsystem vendor ID
2Ch
Reserved
30h
Reserved
Capabilities pointer
34h
Interrupt line
3Ch
Reserved
Maximum latency
38h
Minimum grant
Interrupt pin
Reserved
Power management capabilities
PM data (Reserved)
40h
Next item pointer
PMCSR_BSE
Capability ID
44h
Power management CSR
48h
Reserved
4Ch
Reserved
Miscellaneous control
50h
Reserved
54h–F4h
Subsystem access
F8h
Reserved
FCh
11.1 Vendor ID Register
This 16-bit read-only register contains the value 104Ch, which is the vendor ID assigned to Texas Instruments.
Bit
15
14
13
12
11
10
9
Name
8
7
6
5
4
3
2
1
0
Vendor ID
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
1
0
0
0
0
0
1
0
0
1
1
0
0
Register:
Offset:
Type:
Default:
Vendor ID
00h
Read-only
104Ch
11–1
11.2 Device ID Register
This 16-bit read-only register contains the value 8204h assigned by TI to the PCI7410 firmware loading function.
Bit
15
14
13
12
11
10
9
Name
8
7
6
5
4
3
2
1
0
Device ID
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
1
0
0
0
0
0
1
0
0
0
0
0
0
1
0
0
Register:
Offset:
Type:
Default:
Device ID
02h
Read-only
8204h
11.3 Command Register
This register provides control over the PCI7410 interface to the PCI bus. All bit functions adhere to the definitions in
the PCI Local Bus Specification. See Table 11–2 for a complete description of the register contents.
Bit
15
14
13
12
11
10
9
Name
8
7
6
5
4
3
2
1
0
Command
Type
R
R
R
R
R
RW
R
RW
R
RW
R
RW
R
RW
RW
RW
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Command
04h
Read-only, Read/Write
0000h
Table 11–2. Command Register Description
BIT
SIGNAL
TYPE
15–11
RSVD
R
10
INT_DISABLE
RW
FUNCTION
Reserved. Bits 15–11 return 0s when read.
INTx disable. When set, this bit disables the function from asserting interrupts on the INTx signals.
Since the firmware loader function does not signal interrupts, this bit has no effect on the function.
0 = INTx assertion is enabled (default)
1 = INTx assertion is disabled
This bit is disabled (read-only 0) if bit 0 (PCI2_3_EN) in the miscellaneous control register (see
Section 11.24) is 0.
11–2
Fast back-to-back enable. The PCI7410 device does not generate fast back-to-back transactions;
thus, this bit returns 0 when read.
9
FBB_EN
R
8
SERR_EN
RW
7
RSVD
R
6
PERR_EN
RW
Parity error enable. When set, the PCI7410 device is enabled to drive the PERR response to parity
errors through the PERR signal.
5
VGA_EN
R
VGA palette snoop enable. The PCI7410 device does not feature VGA palette snooping; thus, this
bit returns 0 when read.
4
MWI_EN
RW
Memory write-and-invalidate (MWI) enable. This bit is hardwired to 0 since the firmware loader is a
slave-only function.
3
SPECIAL
R
Special cycle enable. The PCI7410 device does not respond to special cycle transactions. This bit
returns 0 when read.
2
MASTER_ENB
RW
Bus master enable. This bit is hardwired to 0 since the firmware loader is a slave-only function.
1
MEMORY_ENB
RW
Memory response enable. This bit is hardwired to 0 since the firmware loader does not respond to
memory cycles.
0
IO_EN
RW
I/O space enable. Setting this bit to 1 enables the PCI7410 device to respond to I/O space accesses.
SERR enable. When set, the PCI7410 SERR driver is enabled. SERR can be asserted after
detecting an address parity error on the PCI bus.
Reserved. Bit 7 returns 0 when read.
11.4 Status Register
This register provides device information to the host system. Bits in this register may be read normally. A bit in the
status register is reset when a 1 is written to that bit location; a 0 written to a bit location has no effect. All bit functions
adhere to the definitions in the PCI Local Bus Specification. See Table 11–3 for a complete description of the register
contents.
Bit
15
14
13
12
11
10
9
8
Name
Type
Default
7
6
5
4
3
2
1
0
Status
RCU
RCU
RCU
RCU
RCU
R
R
RCU
R
R
R
R
R
R
R
R
0
0
0
0
0
0
1
0
0
0
0
1
0
0
0
0
Register:
Offset:
Type:
Default:
Status
06h
Read-only, Read/Clear/Update
0210h
Table 11–3. Status Register Description
BIT
SIGNAL
TYPE
FUNCTION
15
PAR_ERR
RCU
Detected parity error. This bit is set when a parity error is detected, either an address- or data-parity
error.
14
SYS_ERR
RCU
Signaled system error. This bit is set when SERR is enabled and the PCI7410 device has signaled a
system error to the host.
13
MABORT
RCU
Received master abort. This bit is set when a cycle initiated by the PCI7410 device on the PCI bus
has been terminated by a master abort.
12
TABORT_REC
RCU
Received target abort. This bit is set when a cycle initiated by the PCI7410 device on the PCI bus
has been terminated by a target abort.
11
TABORT_SIG
RCU
Signaled target abort. This bit is set by the PCI7410 device when it terminates a transaction on the
PCI bus with a target abort.
10–9
PCI_SPEED
R
DEVSEL timing. These bits encode the timing of DEVSEL and are hardwired 01b, indicating that the
PCI7410 device asserts this signal at a medium speed on nonconfiguration cycle accesses.
Data parity error detected. This bit is set when the following conditions have been met:
a. PERR was asserted by any PCI device, including the PCI7410 device.
b. The PCI7410 device was the bus master during the data parity error.
c. The parity error response bit is set in the command register.
8
DATAPAR
RCU
7
FBB_CAP
R
Fast back-to-back capable. The PCI7410 device cannot accept fast back-to-back transactions; thus,
this bit is hardwired to 0.
6
UDF
R
UDF supported. The PCI7410 device does not support the user definable features; thus, this bit is
hardwired to 0.
5
66MHZ
R
66-MHz capable. The PCI7410 device operates at a maximum PCLK frequency of 33 MHz;
therefore, this bit is hardwired to 0.
4
CAPLIST
R
Capabilities list. This bit returns 1 when read, indicating that the firmware loading function of the
PCI7410 device supports additional PCI capabilities.
3
INT_STATUS
R
Interrupt status. This bit reflects the interrupt status of the function. Since the firmware loader
function does not signal interrupts, this bit is hardwired to 0. This bit is disabled (read-only 0) if bit 0
(PCI2_3_EN) in the miscellaneous control register (see Section 11.24) is 0.
2–0
RSVD
R
Reserved. Bits 2–0 return 0s when read.
11–3
11.5 Class Code and Revision ID Register
This read-only register categorizes the base class, subclass, and programming interface of the function. The base
class is 08h, identifying the function as a generic system peripheral. The subclass is 80h, identifying the function as
an other system peripheral. The programming interface is 00h. Furthermore, the TI chip revision (00h) is indicated
in the lower byte. See Table 11–4 for a complete description of the register contents.
Bit
31
30
29
28
27
26
Name
25
24
23
22
21
20
19
18
17
16
Class code and revision ID
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
1
0
0
0
1
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Class code and revision ID
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Class code and revision ID
08h
Read-only
0880 0000h
Table 11–4. Class Code and Revision ID Register Description
BIT
SIGNAL
TYPE
DESCRIPTION
31–24
BASECLASS
R
Base class. This field returns 08h when read, which broadly classifies the function as a generic
system peripheral.
23–16
SUBCLASS
R
Subclass. This field returns 80h when read, which specifically classifies the function as other system
peripheral.
15–8
PGMIF
R
Programming interface. This field returns 00h when read.
7–0
CHIPREV
R
Silicon revision. This field returns the silicon revision of PCI7410 device.
11.6 Cache Line Size Register
This read/write register is programmed by host software to indicate the system cache line size.
Bit
7
6
5
Name
4
3
2
1
0
Cache line size
Type
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Cache line size
0Ch
Read-only
00h
11.7 Latency Timer Register
This read/write register specifies the latency timer for PCI7410 device, in units of PCI clock cycles.
Bit
7
6
5
4
3
2
1
0
Type
R
R
R
R
Default
0
0
0
R
R
R
R
0
0
0
0
0
Name
Latency timer
Register:
Offset:
Type:
Default:
11–4
Latency timer
0Dh
Read-only
00h
11.8 Header Type Register
This read-only register indicates that this function has a standard PCI header type.
Bit
7
6
5
4
Name
3
2
1
0
Header type
Type
R
R
R
R
R
R
R
R
Default
1
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Header type
0Eh
Read-only
80h
11.9 BIST Register
Because the PCI7410 device does not support a built-in self test (BIST), this read-only register returns the value of
00h when read.
Bit
7
6
5
4
Name
3
2
1
0
BIST
Type
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
BIST
0Fh
Read-only
00h
11.10 Base Address Register
This register specifies the base address of a 4-byte I/O space used for loading the PCI7410 firmware. See Table 11–5
for a complete description of the register contents.
Bit
31
30
29
28
27
26
25
Name
Type
24
23
22
21
20
19
18
17
16
Base address
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Type
Default
Base address
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
R
R
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
Register:
Offset:
Type:
Default:
Base address
10h
Read-only, Read/Write
0000 0001h
Table 11–5. Base Address Register Description
BIT
SIGNAL
TYPE
31–2
BAR
RW
FUNCTION
1
RSVD
R
Reserved. Bit 1 returns 0 when read.
0
IO_INDICATOR
R
I/O space indicator. This bit is hardwired to 1 to indicate that the base address maps into I/O space.
Base address. This field specifies the upper 30 bits of the 32-bit starting base address.
11–5
11.11 Subsystem Vendor ID Register
This register, used for system and option card identification purposes, may be required for certain operating systems.
This read-only register is initialized through the EEPROM and can be written through an alias register at PCI offset
F8h.
Bit
15
14
13
12
11
10
9
Name
8
7
6
5
4
3
2
1
0
Subsystem vendor ID
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Subsystem vendor ID
2Ch
Read-only
0000h
11.12 Subsystem ID Register
This register, used for system and option card identification purposes, may be required for certain operating systems.
This read-only register is initialized through the EEPROM and can be written through an alias register at PCI offset
F8h.
Bit
15
14
13
12
11
10
9
8
Type
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
Name
7
6
5
4
3
2
1
0
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
Subsystem ID
Register:
Offset:
Type:
Default:
Subsystem ID
2Eh
Read-only
0000h
11.13 Capabilities Pointer Register
This read-only register provides a pointer into the PCI configuration header where the PCI power management
block resides. Because the PCI power management registers begin at 44h, this register is hardwired to 44h.
Bit
7
6
5
Name
4
3
2
1
0
Capabilities pointer
Type
R
R
R
R
R
R
R
R
Default
0
1
0
0
0
1
0
0
Register:
Offset:
Type:
Default:
11–6
Capabilities pointer
34h
Read-only
44h
11.14 Interrupt Line Register
Since the firmware loader function does not signal interrupts, this register is implemented as read-only returning 00h.
Bit
7
6
5
4
3
2
1
0
Type
R
R
R
R
Default
0
0
0
R
R
R
R
0
0
0
0
0
Name
Interrupt line
Register:
Offset:
Type:
Default:
Interrupt line
3Ch
Read-only
00h
11.15 Interrupt Pin Register
Since the firmware loader function does not signal interrupts, this register is implemented as read-only returning 00h.
Bit
7
6
5
4
Name
3
2
1
0
Interrupt pin
Type
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Interrupt pin
3Dh
Read-only
00h
11.16 Minimum Grant Register
Since the firmware loader function is a slave-only function, this register is implemented as read-only returning 00h.
Bit
7
6
5
4
3
2
1
0
Type
R
R
R
R
Default
0
0
0
R
R
R
R
0
0
0
0
0
Name
Minimum grant
Register:
Offset:
Type:
Default:
Minimum grant
3Eh
Read-only
00h
11.17 Maximum Latency Register
Since the firmware loader function is a slave-only function, this register is implemented as read-only returning 00h.
Bit
7
6
5
Name
4
3
2
1
0
Maximum latency
Type
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Maximum latency
3Fh
Read-only
00h
11–7
11.18 Capability ID Register
This read-only register identifies the linked list item as the register for PCI power management. The register returns
01h when read.
Bit
7
6
5
4
Name
3
2
1
0
Capability ID
Type
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
1
Register:
Offset:
Type:
Default:
Capability ID
44h
Read-only
01h
11.19 Next-Item Pointer Register
The contents of this read-only register indicate the next item in the linked list of capabilities for the PCI7410 device.
Because PCI power management is the only entry in the capabilities list for the firmware loading function of the
PCI7410 device, this register returns 00h when read.
Bit
7
6
5
4
Type
R
R
R
R
Default
0
0
0
0
Name
2
1
0
R
R
R
R
0
0
0
0
Next-item pointer
Register:
Offset:
Type:
Default:
11–8
3
Next-item pointer
45h
Read-only
00h
11.20 Power-Management Capabilities Register
This register indicates the capabilities of the firmware loading function of the PCI7410 device related to PCI power
management. See Table 11–6 for a complete description of the register contents.
Bit
7
6
5
Name
4
3
2
1
0
Power-management capabilities
Type
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Power-management capabilities
46h
Read-only
00h
Table 11–6. Power-Management Capabilities Register Description
BIT
SIGNAL
TYPE
FUNCTION
15–11
PME_SUPPORT
R
PME support. This 5-bit field indicates the power states from which the PCI7410 device can assert
PME. These five bits return a value of 00000b by default, indicating that the firmware loading function
does not assert PME.
10
D2_SUPPORT
R
This bit returns a 0 when read, indicating that the function does not support the D2 device power
state.
9
D1_SUPPORT
R
This bit returns a 0 when read, indicating that the function does not support the D1 device power
state.
8–6
AUX_CURRENT
R
3.3-Vaux auxiliary power requirements. Because this function does not support PME generation from
D3cold, this field returns 000b when read.
5
DSI
R
Device specific initialization. This bit returns 0 when read, indicating that the PCI7410 device does not
require special initialization beyond the standard PCI configuration header before a generic class
driver is able to use it.
4
RSVD
R
Reserved. Bit 4 returns 0 when read.
3
PME_CLK
R
PME clock. This bit returns 0 when read, because the firmware loading function of the PCI7410
device does not support PME generation.
2–0
PM_VERSION
R
Power management version. This field returns 010b, indicating revision 1.1 compatibility.
11–9
11.21 Power-Management Control/Status Register
This register determines and changes the current power state of the firmware loading function of the PCI7410 device.
The contents of this register are not affected by the internally generated reset caused by the transition from the D3hot
to D0 state. See Table 11–7 for a complete description of the register contents.
Bit
15
14
13
12
11
10
Name
Type
Default
9
8
7
6
5
4
3
2
1
0
Power-management control/status
RC
R
R
R
R
R
R
R
R
R
R
R
R
R
RW
RW
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Power-management control/status
48h
Read-only, Read/Clear, Read/Write
0000h
Table 11–7. Power-Management Control/Status Register Description
BIT
SIGNAL
TYPE
15
PME_STAT
RC
14–13
DATA_SCALE
R
Data scale. This 2-bit field returns 0s when read because the firmware loading function does not use
the data register.
12–9
DATA_SEL
R
Data select. This 4-bit field returns 0s when read because the firmware loading function does not use
the data register.
8
PME_EN
R
PME enable. This bit defaults to 0 because the firmware loading function does not support PME
generation from any state.
7–2
RSVD
R
Reserved. Bits 7–2 return 0s when read.
1–0
PWR_STATE
RW
DESCRIPTION
PME status. This bit defaults to 0 because the firmware loading function does not support PME
generation from any state.
Power state. This 2-bit field is used both to determine the current power state of the function and to
set the function into a new power state. This field is encoded as follows:
00 = D0
01 = D1
10 = D2
11 = D3hot
11.22 Power-Management Bridge Support Extension Register
This read-only register is not applicable to the firmware loading function of the PCI7410 device and returns 00h when
read.
Bit
7
6
5
Name
4
3
2
1
0
Power-management bridge support extension
Type
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
11–10
Power-management bridge support extension
4Ah
Read-only
00h
11.23 Power-Management Data Register
The read-only register is not applicable to the firmware loading function of the PCI7410 device and returns 00h when
read.
Bit
7
6
5
Name
4
3
2
1
0
Power-management data
Type
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Power-management data
4Bh
Read-only
00h
11.24 Miscellaneous Control Register
This register contains the miscellaneous control bits for the firmware loader function. See Table 11–8 for a complete
description of the register contents.
Bit
7
6
5
Type
R
R
R
R
Default
0
0
0
0
Name
4
3
2
1
0
R
R
R
R
0
0
0
0
Miscellaneous control
Register:
Offset:
Type:
Default:
Miscellaneous control
50h
Read-only, Read/Write
00h
Table 11–8. Miscellaneous Control Register Description
BIT
SIGNAL
TYPE
7–1
RSVD
R
0
PCI2_3_EN
RW
DESCRIPTION
Reserved. Bits 7–1 return 0s when read.
PCI 2.3 enable. When this bit is set, the firmware loader function conforms to the PCI Local Bus
Specification (Revision 2.3). When in the PCI 2.3 mode, bit 10 (INT_DISABLE) in the command
register (see Section 11.3) and bit 3 (INT_STATUS) in the status register (see Section 11.4) are
functional. When this bit is cleared, the function conforms to the PCI Local Bus Specification
(Revision 2.2) and all PCI 2.3 bits are disabled.
0 = PCI 2.2 mode (default)
1 = PCI 2.3 mode
11–11
11.25 Subsystem Access Register
This register is a read/write register and the contents of this register are aliased to the subsystem vendor ID register
at PCI offset 2Ch (see Section 11.11) and subsystem ID register at PCI offset 2Eh (see Section 11.12). See Table 11–9
for a complete description of the register contents.
Bit
31
30
29
28
27
26
25
Name
24
23
22
21
20
19
18
17
16
Subsystem access
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Name
Subsystem access
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Subsystem access
F8h
Read/Write
0000 0000h
Table 11–9. Subsystem Access Register Description
BIT
SIGNAL
TYPE
31–16
SubsystemID
RW
Subsystem ID. The value written to this field is aliased to the subsystem ID register at PCI offset
2Eh.
15–0
SubsystemVendorID
RW
Subsystem vendor ID. The value written to this field is aliased to the subsystem vendor ID
register at PCI offset 2Ch.
11–12
DESCRIPTION
12 Electrical Characteristics
12.1 Absolute Maximum Ratings Over Operating Temperature Ranges†
Supply voltage range, VR_PORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.2 V to 2.2 V
ANALOGVCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 4 V
VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 4 V
PLLVCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 4 V
VCCCB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 5.5 V
VCCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 5.5 V
Clamping voltage range, VCCP and VCCCB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 6 V
Input voltage range, VI: PCI, CardBus, PHY, miscellaneous . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V
Output voltage range, VO: PCI, CardBus, PHY, miscellaneous . . . . . . . . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V
Input clamp current, IIK (VI < 0 or VI > VCC) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA
Output clamp current, IOK (VO < 0 or VO > VCC) (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA
Operating free-air temperature, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
Virtual junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
† Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only and
functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied.
Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. Applies for external input and bidirectional buffers. VI > VCC does not apply to fail-safe terminals. PCI terminals and miscellaneous
terminals are measured with respect to VCCP instead of VCC. PC Card terminals are measured with respect to CardBus VCC. The
limit specified applies for a dc condition.
2. Applies for external output and bidirectional buffers. VO > VCC does not apply to fail-safe terminals. PCI terminals and miscellaneous
terminals are measured with respect to VCCP instead of VCC. PC Card terminals are measured with respect to CardBus VCC. The
limit specified applies for a dc condition.
12.2 Recommended Operating Conditions (see Note 3)
OPERATION
VR_PORT
MIN
NOM
MAX
UNIT
1.8 V
1.6
1.8
2
V
ANALOGVCC
3.3 V
3
3.3
3.6
V
VCC
3.3 V
3
3.3
3.6
V
PLLVCC
3.3 V
3
3.3
3.6
V
3.3 V
3
3.3
3.6
4.75
5
5.25
3
3.3
3.6
4.75
5
5.25
(see Table 2–5 for description)
VCCP
PCI and miscellaneous
miscellaneo s I/O clamp voltage
oltage
VCCCB
PC Card
C d I/O clamp
l
voltage
lt
5V
3.3 V
5V
V
V
NOTE 3: Unused terminals (input or I/O) must be held high or low to prevent them from floating.
12–1
Recommended Operating Conditions (continued)
OPERATION
MIN
3.3 V
0.5 VCCP
PCI
5V
3.3 V CardBus
VIH†
High-level input
voltage
PC Card
3.3 V 16-bit
5 V 16-bit
PC(0–2)
VI
VO§
Input
In
ut voltage
Output
Out
ut voltage
0.475 VCC(A/B)
2
2.4
3.3 V
0
5V
0
3.3 V CardBus
0
MAX
UNIT
VCCP
VCCP
V
VCC(A/B)
VCC(A/B)
V
VCC(A/B)
VCC
2
PCI
Low-level
Low
level in
input
ut voltage
2
0.7 VCC
Miscellaneous‡
VIL†
NOM
VCC
0.8
V
V
0.325 VCC(A/B)
3.3 V 16-bit
0
0.8
V
5 V 16-bit
0
0.8
V
PC(0–2)
0
0.2 VCC
V
Miscellaneous‡
0
0.8
V
PCI
0
PC Card
0
Miscellaneous‡
0
PCI
0
PC Card
0
VCC
VCC
Miscellaneous‡
0
VCC
1
4
0
6
–5.6
1.3
PC Card
VCCP
VCCCB
VCC
Input
In
ut transition time
(tr and tf)
PCI and PC Card
Miscellaneous‡
IO
Output current
TPBIAS outputs
Differential in
input
ut
voltage
Cable inputs during data reception
118
260
VID
Cable inputs during arbitration
168
265
Common mode in
Common-mode
input
ut
voltage
TPB cable inputs, source power node
0.4706
VIC
TPB cable inputs, nonsource power node
0.4706
2.515
2.015¶
tPU
Powerup reset time
GRST input
2
TPA, TPB cable in
inputs
uts
B
t
TPA and
d TPB
Between
cable inputs
V
V
ns
mA
mV
V
ms
±1.08
S100 operation
Receive in
input
ut skew
V
0.3 VCCP
tt
Receive in
input
ut jitter
V
S200 operation
±0.5
S400 operation
±0.315
S100 operation
±0.8
S200 operation
±0.55
ns
ns
±0.5
S400 operation
TA
Operating ambient temperature range
0
25
70
°C
TJ#
Virtual junction temperature
0
25
115
°C
† Applies to external inputs and bidirectional buffers without hysteresis
‡ Miscellaneous terminals are 1, 2, 12, 17, 111, 112, 125, 167, 181, and 187 for the PDV packaged device and B10, C09, D01, E03, F12, G03,
H02, L17, P17, and P18 for the GHK packaged device (CNA, SCL, SDA, SUSPEND, GRST, CDx, PHY_TEST_MA, and VSx terminals).
§ Applies to external output buffers
¶ For a node that does not source power, see Section 4.2.2.2 in IEEE Std 1394a–2000.
# These junction temperatures reflect simulation conditions. The customer is responsible for verifying junction temperature.
12–2
12.3 Electrical Characteristics Over Recommended Operating Conditions (unless
otherwise noted)
PARAMETER
TERMINALS
PCI
VOH
Hi h l
High-level
l output
t t voltage
lt
PC Card
OPERATION
IOH = –0.5 mA
5V
3.3 V CardBus
IOH = –2 mA
IOH = –0.15 mA
0.9 VCC
3.3 V 16-bit
IOH = –0.15 mA
2.4
5 V 16-bit
IOH = –0.15 mA
2.8
IOH = –4
4 mA
Low level output voltage
Low-level
PC Card
3.3 V CardBus
IOL = 0.7 mA
3.3 V 16-bit
IOL = 0.7 mA
5 V 16-bit
IOL = 0.7 mA
IOZ
3-state output high-impedance
Output terminals
IOZL
High-im edance, low-level
High-impedance,
output current
Output terminals
IOZH
High-im edance, high-level
High-impedance,
output current
Output terminals
IIL
L
l
l input
i
t currentt
Low-level
IIH
High level input current
High-level
VCC–0.6
06
0.1 VCC
0.55
0.1 VCC
0.55
0.5
VO = VCC or GND
±20
3.6 V
VI = VCC
VI = VCC
–1
10
5.25 V
VI = VCC†
VI = VCC†
–1
25
±20
Input terminals
3.6 V
VI = GND
3.6 V
±20
PCI
3.6 V
VI = GND
VI = VCC‡
Others
3.6 V
VI = VCC‡
VI = VCC‡
±20
3.6 V
µA
µA
A
µA
A
A
µA
±20
10
20
3.6 V
VI = VCC‡
VI = VCC‡
5.25 V
VI = VCC‡
25
5.25 V
V
0.4
I/O terminals
I/O terminals
V
IOL = 4 mA
3.6 V
Input terminals
V
3.6 V
5.25 V
UNIT
2.4
IOL = 6 mA
5V
Miscellaneous§
MAX
0.9 VCC
IOL = 1.5 mA
3.3 V
VOL
MIN
3.3 V
Miscellaneous§
PCI
TEST CONDITIONS
µA
10
† For PCI and miscellaneous terminals, VI = VCCP. For PC Card terminals, VI = VCC(A/B).
‡ For I/O terminals, input leakage (IIL and IIH) includes IOZ leakage of the disabled output.
§ Miscellaneous terminals are 1, 2, 12, 17, 111, 112, 125, 167, 181, and 187 for the PDV packaged device and B10, C09, D01, E03, F12, G03,
H02, L17, P17, and P18 for the GHK packaged device (CNA, SCL, SDA, SUSPEND, GRST, CDx, PHY_TEST_MA, and VSx terminals).
12.4 Electrical Characteristics Over Recommended Ranges of Operating Conditions
(unless otherwise noted)
12.4.1 Device
PARAMETER
TEST CONDITION
VTH
VO
Power status threshold, CPS input†
400-kΩ resistor†
TPBIAS output voltage
At rated IO current
II
Input current (PC0–PC2 inputs)
VCC = 3.6 V
MIN
MAX
4.7
7.5
UNIT
V
1.665
2.015
V
5
µA
† Measured at cable power side of resistor.
12–3
12.4.2 Driver
PARAMETER
TEST CONDITION
VOD
IDIFF
Differential output voltage
56 Ω,
Driver difference current, TPA+, TPA–, TPB+, TPB–
Drivers enabled, speed signaling off
ISP200
ISP400
Common-mode speed signaling current, TPB+, TPB–
S200 speed signaling enabled
Common-mode speed signaling current, TPB+, TPB–
S400 speed signaling enabled
See Figure 12–1
MIN
MAX
UNIT
172
–1.05†
265
1.05†
mV
–4.84‡
–12.4‡
–2.53‡
–8.10‡
mA
mA
mA
VOFF
Off state differential voltage
Drivers disabled,
See Figure 12–1
20
mV
† Limits defined as algebraic sum of TPA+ and TPA– driver currents. Limits also apply to TPB+ and TPB– algebraic sum of driver currents.
‡ Limits defined as absolute limit of each of TPB+ and TPB– driver currents.
TPAx+
TPBx+
56 Ω
TPAx–
TPBx–
Figure 12–1. Test Load Diagram
12.4.3 Receiver
PARAMETER
TEST CONDITION
MIN
TYP
4
7
MAX
UNIT
kΩ
ZID
Differential impedance
Drivers disabled
ZIC
Common mode impedance
Common-mode
Drivers disabled
VTH–R
VTH–CB
Receiver input threshold voltage
Drivers disabled
–30
Cable bias detect threshold, TPBx cable inputs
Drivers disabled
0.6
1.0
V
VTH+
VTH–
Positive arbitration comparator threshold voltage
Drivers disabled
89
168
mV
Negative arbitration comparator threshold voltage
Drivers disabled
–168
–89
mV
VTH–SP200
VTH–SP400
Speed signal threshold
TPBIAS–TPA common mode
voltage, drivers disabled
49
131
mV
314
396
mV
4
20
Speed signal threshold
pF
kΩ
24
pF
30
mV
12.5 PCI Clock/Reset Timing Requirements Over Recommended Ranges of Supply
Voltage and Operating Free-Air Temperature
PARAMETER
tc
tw(H)
Cycle time, PCLK
tw(L)
tr, tf
tw
tsu
Pulse duration (width), GRST
12–4
ALTERNATE
SYMBOL
TEST CONDITIONS
MIN
MAX
UNIT
30
ns
11
ns
Pulse duration (width), PCLK low
tcyc
thigh
tlow
11
ns
Slew rate, PCLK
∆v/∆t
1
trst
1
ms
100
ms
Pulse duration (width), PCLK high
Setup time, PCLK active at end of PRST
trst-clk
4
V/ns
12.6 Switching Characteristics for PHY Port Interface
PARAMETER
tr
tf
TEST CONDITIONS
MIN
Jitter, transmit
Between TPA and TPB
Skew, transmit
Between TPA and TPB
TP differential rise time, transmit
10% to 90%, at 1394 connector
0.5
TP differential fall time, transmit
90% to 10%, at 1394 connector
0.5
TYP
MAX
UNIT
± 0.15
ns
± 0.10
ns
1.2
ns
1.2
ns
12.7 Operating, Timing, and Switching Characteristics of XI
PARAMETER
VDD
VIH
High-level input voltage
VIL
Low-level input voltage
MIN
3.0
TYP
MAX
3.3
3.6
UNIT
V (PLLVCC)
0.63 VCC
V
0.33 VCC
Input clock frequency
V
24.576
MHz
Input clock frequency tolerance
Input slew rate
Input clock duty cycle
<100
PPM
0.2
4
V/ns
40%
60%
12.8 PCI Timing Requirements Over Recommended Ranges of Supply Voltage and
Operating Free-Air Temperature
This data manual uses the following conventions to describe time ( t ) intervals. The format is tA, where subscript A
indicates the type of dynamic parameter being represented. One of the following is used: tpd = propagation delay time,
td (ten, tdis) = delay time, tsu = setup time, and th = hold time.
ALTERNATE
SYMBOL
PARAMETER
tpd
Propagation delay time
time, See Note 4
PCLK-to-shared signal
valid delay time
tval
PCLK-to-shared signal
invalid delay time
tinv
ten
tdis
Enable time, high impedance-to-active delay time from PCLK
tsu
th
Setup time before PCLK valid
Disable time, active-to-high impedance delay time from PCLK
Hold time after PCLK high
TEST CONDITIONS
MIN
CL = 50 pF,
F,
See Note 4
MAX
UNIT
11
ns
2
ton
toff
2
ns
tsu
th
7
ns
0
ns
28
ns
NOTE 4: PCI shared signals are AD31–AD0, C/BE3–C/BE0, FRAME, TRDY, IRDY, STOP, IDSEL, DEVSEL, and PAR.
12–5
12–6
13 Mechanical Information
The PCI7410 is packaged in either a 209-ball GHK BGA or a 208-pin PDV package. The following shows the
mechanical dimensions for the GHK and PDV packages.
GHK (S-PBGA-N209)
PLASTIC BALL GRID ARRAY
16,10
SQ
15,90
14,40 TYP
0,80
W
V
U
T
R
P
N
M
L
K
J
H
G
F
E
D
C
B
A
0,80
1
3
2
0,95
0,85
5
4
7
6
9
8
11
10
13
12
15
14
17
16
19
18
1,40 MAX
Seating Plane
0,12
0,08
0,55
0,45
0,08 M
0,45
0,35
0,10
4145273–2/B 12/98
NOTES: B. All linear dimensions are in millimeters.
C. This drawing is subject to change without notice.
D. MicroStar BGA configuration.
MicroStar BGA is a trademark of Texas Instruments.
13–1
PDV (S-PQFP-G208)
PLASTIC QUAD FLATPACK
156
105
157
104
0,27
0,17
0,08 M
0,50
0,13 NOM
208
53
1
52
Gage Plane
25,50 TYP
28,05 SQ
27,95
0,25
0,05 MIN
0°–ā7°
30,10
SQ
29,90
0,75
0,45
1,45
1,35
Seating Plane
0,08
1,60 MAX
4087729/B 06/96
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Falls within JEDEC MO-136
13–2