ADS824 AD S 824 E SBAS076A – MAY 2001 10-Bit, 70MHz Sampling ANALOG-TO-DIGITAL CONVERTER TM FEATURES DESCRIPTION ● ● ● ● ● The ADS824 is a pipeline, CMOS Analog-to-Digital (A/D) converter that operates from a single +5V power supply. This converter provides excellent performance with a single-ended input and can be operated with a differential input for added spurious performance. This high performance converter includes a 10-bit quantizer, high bandwidth track/hold, and a high accuracy internal reference. It also allows for the user to disable the internal reference and utilize external references. This external reference option provides excellent gain and offset matching when used in multi-channel applications or in applications where full scale range adjustment is required. ● ● ● ● ● ● HIGH SNR: 59dB HIGH SFDR: 70dB LOW POWER: 315mW INTERNAL/EXTERNAL REFERENCE OPTION SINGLE-ENDED OR DIFFERENTIAL ANALOG INPUT PROGRAMMABLE INPUT RANGE: 1Vp-p or 2Vp-p LOW DNL: 0.3LSB SINGLE +5V SUPPLY OPERATION +3V DIGITAL OUTPUT CAPABILITY POWER DOWN: 20mW SSOP-28 PACKAGE The ADS824 is specified at a maximum sampling frequency of 70MHz and a single-ended input range of 1.5V to 3.5V. The ADS824 is available in an SSOP-28 package and is pin compatible with the 10-bit, 40MHz ADS822 and the 10-bit, 60MHz ADS823. APPLICATIONS ● ● ● ● The ADS824 employs digital error correction techniques to provide excellent differential linearity for demanding imaging applications. Its low distortion and high SNR give the extra margin needed for medical imaging, communications, video, and test instrumentation. The ADS824 offers power dissipation of 315mW and also provides a power-down mode, thus reducing power dissipation to only 20mW. MEDICAL IMAGING HDTV VIDEO DIGITIZING COMMUNICATIONS TEST EQUIPMENT +VS CLK VDRV ADS824 Timing Circuitry VIN IN IN T/H 10-Bit Pipelined A/D Core Error Correction Logic 3-State Outputs D0 • • • D9 Internal Reference CM Optional External Reference Int/Ext PD OE Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright © 1997, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. www.ti.com ELECTROSTATIC DISCHARGE SENSITIVITY ABSOLUTE MAXIMUM RATINGS +VS ....................................................................................................... +6V Analog Input ............................................................. –0.3V to (+VS + 0.3V) Logic Input ............................................................... –0.3V to (+VS + 0.3V) Case Temperature ......................................................................... +100°C Junction Temperature .................................................................... +150°C Storage Temperature ..................................................................... +150°C This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. DEMO BOARD ORDERING INFORMATION PRODUCT DEMO BOARD ADS824E DEM-ADS824E PACKAGE/ORDERING INFORMATION PRODUCT PACKAGE PACKAGE DRAWING NUMBER ADS824E " SSOP-28 " 324 " SPECIFIED TEMPERATURE RANGE PACKAGE MARKING ORDERING NUMBER(1) TRANSPORT MEDIA –40°C to +85°C " ADS824E " ADS824E ADS824E/1K Rails Tape and Reel NOTES: (1) Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., /1K indicates 1000 devices per reel). Ordering 1000 pieces of ADS824E/1K” will get a single 1000-piece Tape and Reel. ELECTRICAL CHARACTERISTICS At TA = full specified temperature range, single-ended input range = 1.5V to 3.5V, sampling rate = 70MHz, external reference, unless otherwise noted. ADS824E PARAMETER CONDITIONS MIN RESOLUTION SPECIFIED TEMPERATURE RANGE ANALOG INPUT Standard Single-Ended Input Range Optional Single-Ended Input Range Common-Mode Voltage Optional Differential Input Range Analog Input Bias Current Input Impedance Track-Mode Input Bandwidth Ambient Air 2Vp-p 1Vp-p 1.5 2 2Vp-p 2 2 MAX Bits –40 to +85 °C 3.5 3 3 1 1.25 || 5 300 –3dBFS UNITS 10 Guaranteed 2.5 CONVERSION CHARACTERISTICS Sample Rate Data Latency DYNAMIC CHARACTERISTICS Differential Linearity Error (largest code error) f = 1MHz f = 10MHz No Missing Codes Integral Nonlinearity Error, f = 1MHz Spurious Free Dynamic Range(1) f = 1MHz f = 10MHz Two-Tone Intermodulation Distortion(3) f = 4.5MHz and 5.5MHz (–7dB each tone) Signal-to-Noise Ratio (SNR) f = 1MHz f = 10MHz Signal-to-(Noise + Distortion) (SINAD) f = 1MHz f = 10MHz Effective Number of Bits(4), f = 1MHz Output Noise Aperture Delay Time Aperture Jitter Overvoltage Recovery Time Full-Scale Step Acquisition Time TYP 10k 70M Samples/s Clk Cyc ±1.0 LSB LSB ±3.0 LSBs 5 ±0.3 ±0.3 Guaranteed ±0.5 V V V V µA MΩ || pF MHz Referred to Full Scale 60 70 68 dBFS(2) dBFS –63.4 dBc 59 59 dB dB 58 58 9.3 0.2 3 1.2 2 5 dB dB Bits LSBs rms ns ps rms ns ns Referred to Full Scale 55 Referred to Full Scale 50 Input Grounded ADS824 SBAS076A ELECTRICAL CHARACTERISTICS (Cont.) At TA = full specified temperature range, single-ended input range = 1.5V to 3.5V, sampling rate = 70MHz, external reference, unless otherwise noted. ADS824E PARAMETER DIGITAL INPUTS Logic Family Convert Command High Level Input Current(5) (VIN = 5V) Low Level Input Current (VIN = 0V) High Level Input Voltage Low Level Input Voltage Input Capacitance DIGITAL OUTPUTS Logic Family Logic Coding Low Output Voltage (IOL = 50µA) Low Output Voltage, (IOL = 1.6mA) High Output Voltage, (IOH = 50µA) High Output Voltage, (IOH = 0.5mA) Low Output Voltage, (IOL = 50µA) High Output Voltage, (IOH = 50µA) 3-State Enable Time 3-State Disable Time Output Capacitance CONDITIONS TYP MAX CMOS-Compatible Rising Edge of Convert Clock Start Conversion 100 10 +3.5 +1.0 5 UNITS µA µA V V pF CMOS-Compatible Straight Offset Binary VDRV = 5V +0.1 +0.2 +4.9 +4.8 VDRV = 3V +0.1 +2.8 OE = L OE = H ACCURACY (Internal Reference, 2Vp-p, Unless Otherwise Noted) fS = 2.5MHz Zero Error (Referred to –FS) at 25°C Zero Error Drift (Referred to –FS) Gain Error(6) at 25°C Gain Error Drift(6) Gain Error(7) at 25°C Gain Error Drift(7) Power Supply Rejection of Gain ∆ VS = ±5% REFT Tolerance Deviation from Ideal 3.5V REFB Tolerance Deviation From Ideal 1.5V External REFT Voltage Range External REFB Voltage Range Reference Input Resistance POWER SUPPLY REQUIREMENTS Supply Voltage: +VS Supply Current: +IS Output Driver Supply Current (VDRV) Power Dissipation: VDRV = 5V VDRV = 3V VDRV = 5V VDRV = 3V Power Down Thermal Resistance, θJA SSOP-28 MIN Operating Operating External Reference External Reference Internal Reference Internal Reference Operating REFB + 0.8 1.25 +4.75 20 2 5 40 10 ±0.5 12 ±1.5 38 ±0.75 20 68 ±10 ±10 3.5 1.5 1.6 ±3.0 +5.0 66 9 330 315 345 335 20 89 ±2.5 ±1.5 ±25 ±25 VS – 1.25 REFT – 0.8 +5.25 375 V V V V V V ns ns pF %FS ppm/°C %FS ppm/°C %FS ppm/°C dB mV mV V V kΩ V mA mA mW mW mW mW mW °C/W NOTES: (1) Spurious Free Dynamic Range refers to the magnitude of the largest harmonic. (2) dBFS means dB relative to Full Scale. (3) Two-tone intermodulation distortion is referred to the largest fundamental tone. This number will be 6dB higher if it is referred to the magnitude of the two-tone fundamental envelope. (4) Effective number of bits (ENOB) is defined by (SINAD – 1.76)/6.02. (5) A 50kΩ pull-down resistor is inserted internally. (6) Includes internal reference. (7) Excludes internal reference. ADS824 SBAS076A 3 PIN CONFIGURATION PIN DESCRIPTIONS Top View SSOP GND 1 28 VDRV Bit 1 (MSB) 2 27 +VS Bit 2 3 26 GND Bit 3 4 25 IN Bit 4 5 24 IN Bit 5 6 23 CM Bit 6 7 22 REFT ADS824 Bit 7 8 21 ByT Bit 8 9 20 ByB Bit 9 10 19 REFB Bit 10 (LSB) 11 18 INT/EXT OE 12 17 RSEL PD 13 16 GND CLK 14 15 +VS PIN DESIGNATOR 1 2 3 4 5 6 7 8 9 10 11 12 GND Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 Bit 8 Bit 9 Bit 10 OE 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 PD CLK +VS GND RSEL INT/EXT REFB ByB ByT REFT CM IN IN GND +VS VDRV DESCRIPTION Ground Data Bit 1 (D9) (MSB) Data Bit 2 (D8) Data Bit 3 (D7) Data Bit 4 (D6) Data Bit 5 (D5) Data Bit 6 (D4) Data Bit 7 (D3) Data Bit 8 (D2) Data Bit 9 (D1) Data Bit 10 (D0) (LSB) Output Enable. HI = high impedance state. LO = normal operation (internal pulldown resistor) Power Down. HI = power down; LO = normal Convert Clock Input +5V Supply Ground Input Range Select. HI = 2Vp-p; LO = 1Vp-p Reference Select. HI = external; LO = internal Bottom Reference Bottom Ladder Bypass Top Ladder Bypass Top Reference Common-Mode Voltage Output Complementary Input (–) Analog Input (+) Ground +5V Supply Output Logic Driver Supply Voltage TIMING DIAGRAM N+2 N+1 Analog In N+3 N tD N+4 N+5 tL tCONV N+7 N+6 tH Clock 5 Clock Cycles t2 Data Out N–5 N–4 N–3 N–2 N–1 Data Invalid SYMBOL tCONV tL tH tD t1 t2 4 N N+1 N+2 t1 DESCRIPTION MIN Convert Clock Period Clock Pulse Low Clock Pulse High Aperture Delay Data Hold Time, CL = 0pF New Data Delay Time, CL = 15pF max 13.4 6.4 6.4 TYP MAX UNITS 100µs ns ns ns ns ns ns 6.7 6.7 3 3.9 12 ADS824 SBAS076A TYPICAL CHARACTERISTICS At TA = full specified temperature range, VS = +5V, single-ended input range = 1.5V to 3.5V, and sampling rate = 70MHz, external reference, unless otherwise noted. SPECTRAL PERFORMANCE (Single-Ended Input, 1Vp-p) SPECTRAL PERFORMANCE 0 0 fIN = 10MHz SNR = 55.7dBFS SFDR = 69.7dBFS fIN = 10MHz –20 Amplitude (dB) Magnitude (dB) –20 –40 –60 –80 –40 –60 –80 –100 –100 0 8.5 17.5 25.75 35 0 8.25 Frequency (MHz) SPECTRAL PERFORMANCE (Differential Input, 2Vp-p) 35 SPECTRAL PERFORMANCE fIN = 10MHz SNR = 59dBFS SFDR = 73dBFS fIN = 20MHz –20 Magnitude (dB) –20 Magnitude (dB) 25.75 0 0 –40 –60 –40 –60 –80 –80 –100 –100 0 8.25 17.5 25.75 0 35 8.25 17.5 25.75 Frequency (MHz) Frequency (MHz) SPECTRAL PERFORMANCE (Single-Ended Input, 1Vp-p) SPECTRAL PERFORMANCE (Differential Input, 2Vp-p) 0 35 0 fIN = 20MHz SNR = 55dBFS SFDR = 69dBFS fIN = 20MHz SNR = 59dBFS SFDR = 69dBFS –20 Magnitude (dB) –20 Magnitude (dB) 17.5 Frequency (MHz) –40 –60 –80 –40 –60 –80 –100 –100 0 8.25 17.5 Frequency (MHz) ADS824 SBAS076A 25.75 35 0 8.25 17.5 25.75 35 Frequency (MHz) 5 TYPICAL CHARACTERISTICS (Cont.) At TA = full specified temperature range, VS = +5V, single-ended input range = 1.5V to 3.5V, and sampling rate = 70MHz, external reference, unless otherwise noted. TWO-TONE INTERMODULATION DISTORTION (Differential Input, 2Vp-p) UNDERSAMPLING (Differential Input, 2Vp-p) 0 0 fS = 41MHz fIN = 75MHz SNR = 58.6dBFS SFDR = 67dBFS –20 Magnitude (dB) Magnitude (dB) –20 f1 = 9.5MHz at –7dBFS f2 = 9.9MHz at –7dBFS IMD (3) = –63.4dBc –40 –60 –40 –60 –80 –80 –100 –100 0 5.13 10.25 15.38 0 20.5 8.75 17.50 26.25 35 Frequency (MHz) Frequency (MHz) DYNAMIC PERFORMANCE vs INPUT FREQUENCY SIGNAL-TO-(NOISE + DISTORTION) vs TEMPERATURE 65 65 SINAD (dBFS) SFDR, SNR (dBFS) 75 SFDR 70 65 SNR 60 fIN = 10MHz 55 fIN = 20MHz 60 50 55 0.1 1 10 –50 100 –25 0 25 50 75 Frequency (MHz) Temperature (°C) DYNAMIC PERFORMANCE vs TEMPERATURE DIFFERENTIAL LINEARITY ERROR vs TEMPERATURE 100 0.35 75 fIN = 10MHz 70 65 DLE (LSB) SFDR, SNR (dBFS) SFDR (fIN = 10MHz) SFDR (fIN = 20MHz) 0.3 0.25 SNR (fIN = 10MHz) 60 SNR (fIN = 20MHz) 0.20 55 –50 –25 0 25 50 Temperature (°C) 6 75 100 –50 –25 0 25 50 75 100 Temperature (°C) ADS824 SBAS076A TYPICAL CHARACTERISTICS (Cont.) At TA = full specified temperature range, VS = +5V, single-ended input range = 1.5V to 3.5V, and sampling rate = 70MHz, external reference, unless otherwise noted. DIFFERENTIAL LINEARITY ERROR POWER DISSIPATION vs TEMPERATURE 1.0 360 VDRV = +5V fIN = 10MHz 0.5 DLE (LSB) Power (mW) 350 340 Internal Reference 0 –0.5 330 External Reference –1.0 320 –50 –25 0 25 50 75 0 100 256 512 768 DIFFERENTIAL LINEARITY ERROR INTEGRAL LINEARITY ERROR 1.0 2.0 fIN = 20MHz fIN = 1MHz 0.5 1.0 ILE (LSB) DLE (LSB) 1024 Output Code Temperature (°C) 0 –0.5 0 –1.0 –1.0 –2.0 0 256 512 768 1024 0 256 Output Code 512 768 1024 Output Code SWEPT POWER SFDR OUTPUT NOISE HISTOGRAM (DC Input) 100 800k fIN = 10MHz 80 dBFS 60 Counts SFDR (dB) 600k dBc 40 400k 200k 20 0 0 –60 –50 –40 –30 –20 Input Amplitude (dBFS) ADS824 SBAS076A –10 0 N-2 N-1 N N+1 N+2 Output Code 7 APPLICATION INFORMATION THEORY OF OPERATION The ADS824 is a high-speed, CMOS A/D converter which employs a pipelined converter architecture consisting of 9 internal stages. Each stage feeds its data into the digital error correction logic ensuring excellent differential linearity and no missing codes at the 10-bit level. The output data becomes valid on the rising clock edge (see Timing Diagram). The pipeline architecture results in a data latency of 5 clock cycles. The analog input of the ADS824 is a differential track and hold (see Figure 1). The differential topology along with tightly matched capacitors produce a high level of acperformance while sampling at very high rates. The ADS824 allows its analog inputs to be driven either single-ended or differentially. The typical configuration for the ADS824 is for the single-ended mode in which the input track-and-hold performs a single-ended-to-differential conversion of the analog input signal. Both inputs (IN, IN) require external biasing using a common-mode voltage that is typically at the mid-supply level (+VS /2). The following application discussion focuses on the singleended configuration. Typically, its implementation is easier to achieve and the rated specifications for the ADS824 are characterized using the single-ended mode of operation. DRIVING THE ANALOG INPUT The ADS824 achieves excellent ac performance either in the single-ended or differential mode of operation. The selection for the optimum interface configuration will depend on the Op Amp Bias φ1 VCM φ1 CH φ2 CI IN IN φ1 φ2 OUT φ1 OUT φ1 CI φ2 CH φ1 φ1 Input Clock (50%) Op Amp Bias VCM Internal Non-overlapping Clock φ1 φ2 φ1 individual application requirements and system structure. For example, communications applications often process a band of frequencies that do not include DC, whereas in imaging applications, the previously restored DC level must be maintained correctly up to the A/D converter. Features on the ADS824 such as the input range select (RSEL pin) or the option for an external reference, provide the needed flexibility to accommodate a wide range of applications. In any case, the ADS824 should be configured such that the application objectives are met while observing the headroom requirements of the driving amplifier in order to yield the best overall performance. INPUT CONFIGURATIONS AC-Coupled, Single-Supply Interface Figure 2 shows the typical circuit for an ac-coupled analog input configuration of the ADS824 while all components are powered from a single +5V supply. With the RSEL pin connected high, the full-scale input range is set to 2Vp-p. In this configuration, the top and bottom references (REFT, REFB) provide an output voltage of +3.5V and +1.5V, respectively. Two resistors ( 2x 1.0kΩ) are used to create a common-mode voltage (VCM) of approximately +2.5V to bias the inputs of the driving amplifier A1. Using the OPA680 on a single +5V supply, its ideal common-mode point is at +2.5V, which coincides with the recommended common-mode input level for the ADS824. This obviates the need of a coupling capacitor between the amplifier and the converter. Even though the OPA680 has an ac gain of +2, the dc gain is only +1 due to the blocking capacitor at resistor RG. The addition of a small series resistor (RS) between the output of the op amp and the input of the ADS824 will be beneficial in almost all interface configurations. This will decouple the op amp’s output from the capacitive load and avoid gain peaking, which can result in increased noise. For best spurious and distortion performance, the resistor value should be kept below 100Ω. Furthermore, the series resistor, in combination with the 10pF capacitor, establishes a passive low-pass filter, limiting the bandwidth for the wideband noise thus, help improving the SNR performance. AC-Coupled, Dual Supply Interface The circuit provided in Figure 3 shows typical connections for the analog input in case the selected amplifier operates on dual supplies. This might be necessary to take full advantage of very low distortion operational amplifiers, like the OPA642. The advantage is that the driving amplifier can be operated with a ground referenced bipolar signal swing. This will keep the distortion performance at its lowest since the signal range stays within the linear region of the op amp and sufficient headroom to the supply rails can be maintained. By capacitively coupling the single-ended signal to the input of the ADS824, its common-mode requirements can easily be satisfied with two resistors connected between the top and bottom reference. FIGURE 1. Simplified Circuit of Input Track-and-Hold with Timing Diagram. 8 ADS824 SBAS076A 1.0kΩ +5V VCM +2.5V 1.0kΩ +5V 0.1µF 50Ω REFB +1.5V RS 50Ω VIN REFT +3.5V RSEL +VS IN OPA680 10pF +VIN 0V ADS824 RF 402Ω –VIN CM IN RG 402Ω 0.1µF INT/EXT 0.1µF GND FIGURE 2. AC-Coupled Input Configuration for a 2Vp-p Full-Scale Range and a Common-Mode Voltage, VCM, at +2.5V Derived From The Internal Top (REFT) and Bottom Reference (REFB). +5V 1.0kΩ +5V RS 24.9Ω VIN REFT +3.5V 0.1µF RSEL +VS IN OPA642 100pF –5V RF 402Ω ADS824 1.0kΩ CM IN RG 402Ω 0.1µF REFB +1.5V INT/EXT GND FIGURE 3. AC-Coupling the Dual Supply Amplifier OPA642 to the ADS823 for a 2Vp-p Full-Scale Input Range. For applications requiring the driving amplifier to provide a signal amplification, with a gain ≥ 5, consider using decompensated voltage-feedback op amps, like the OPA643, or current-feedback op amps like the OPA681 and OPA658. DC-coupled with Level Shift Several applications may require that the bandwidth of the signal path include DC, in which case, the signal has to be DC-coupled to the A/D converter. In order to accomplish this, the interface circuit has to provide a DC level shift to the analog input signal. The circuit shown in Figure 4 employs a dual op amp, A1, to drive the input of the ADS824 and level shift the signal to be compatible with the selected input range. With the RSEL pin tied to the supply and the INT/EXT pin to ground, the ADS824 is configured for a 2Vp-p input range and uses the internal references. The complementary input (IN) may be appropriately biased ADS824 SBAS076A using the +2.5V common-mode voltage available at the CM pin. One-half of amplifier A1 buffers the REFB pin and drives the voltage divider R1, R2. Because of the op amp’s noise gain of +2V/V, assuming RF = RIN, the common-mode voltage (VCM) has to be re-scaled to +1.25. This results in the correct DC level of +2.5V for the signal input (IN). Any DC voltage differences between the IN and IN inputs of the ADS824 effectively produces an offset, which can be corrected for by adjusting the resistor values of the divider, R1 and R2. The selection criteria for a suitable op amp should include the supply voltage, input bias current, output voltage swing, distortion, and noise specification. Note that in this example, the overall signal phase is inverted. To re-establish the original signal polarity, it is always possible to interchange the IN and IN connections. 9 +5V RF 499Ω RIN 499Ω VIN 1/2 OPA2681 +VS RSEL RS 50Ω IN 2Vp-p 10pF ADS824 NOTE: RF = RIN, G = –1 CM (+2.5V) IN +5V 0.1µF REFB (+1.5V) REFT (+3.5V) INT/EXT 50Ω R2 200Ω 0.1µF 1/2 OPA2681 VCM = +1.25V 0.1µF R1 1kΩ RF 1kΩ FIGURE 4. DC-Coupled Interface Circuit with Level Shifting Using Dual Current-Feedback Amplifier OPA2681. SINGLE-ENDED-TO-DIFFERENTIAL CONFIGURATION (Transformer Coupled) If the application requires a signal conversion from a singleended source to feed the ADS824 differentially, a RF transformer might be a good solution. The selected transformer must have a center tap in order to apply the common-mode DC voltage necessary to bias the converter inputs. AC grounding the center tap will generate the differential signal swing across the secondary winding. Consider a stepup transformer to take advantage of a signal amplification without the introduction of another noise source. Furthermore, the reduced signal swing from the source may lead to an improved distortion performance. The differential input configuration may provide a noticeable advantage of achieving good SFDR performance over a wide range of input frequencies. In this mode, both inputs of the ADS824 see matched impedances, and the differential signal swing can be reduced to half of the swing required for single-ended drive. Figure 5 shows the schematic for the suggested transformer-coupled interface circuit. The com- ponent values of the R-C low-pass may be optimized depending on the desired roll-off frequency. The resistor across the secondary side (RT) should be calculated using the equation RT = n2 x RG to match the source impedance (RG) for good power transfer and Voltage Standing Wave Ratio (VSWR). REFERENCE OPERATION Figure 6 depicts the simplified model of the internal reference circuit. The internal blocks are the bandgap voltage reference, the drivers for the top and bottom reference, and RSEL ADS824 50kΩ +VS INT/EXT 50kΩ Bandgap Reference and Logic VREF RG 0.1µF 1:n 22Ω +1 VIN +1 IN 47pF RT ADS824 400Ω 400Ω 400Ω 400Ω 22Ω IN CM RSEL INT/EXT 47pF REFT ByT CM ByB REFB +5V + 10µF 0.1µF Bypass Capacitors: 0.1µF || 2.2µF each FIGURE 5. Transformer Coupled Input. 10 FIGURE 6. Equivalent Reference Circuit with Recommended Reference Bypassing. ADS824 SBAS076A The common-mode voltage available at the CM-pin may be used as a bias voltage to provide the appropriate offset for the driving circuitry. However, care must be taken not to appreciably load this node, which is not buffered and has a high impedance. An alternative way of generating a common-mode voltage is given in Figure 7. Here, two external precision resistors (tolerance 1% or better) are located between the top and bottom reference pins. The commonmode voltage, CMV, will appear at the midpoint. the resistive reference ladder. The bandgap reference circuit includes logic functions that allows setting the analog input swing of the ADS824 to either a 1Vp-p or 2Vp-p full-scale range by simply tying the RSEL pin to a Low or High potential, respectively. While operating the ADS824 in the external reference mode, the buffer amplifiers for the REFT and REFB are disconnected from the reference ladder. As shown, the ADS824 has internal 50kΩ pull-up resistors at the range select pin (RSEL) and reference select pin (INT/EXT). Leaving these pins open configures the ADS824 for a 2Vp-p input range and external reference operation. Setting the ADS824 up for internal reference mode requires to bringing the INT/EXT pin low. EXTERNAL REFERENCE OPERATION For even more design flexibility, the internal reference can be disabled and an external reference voltage be used. The utilization of an external reference may be considered for applications requiring higher accuracy, improved temperature performance, or a wide adjustment range of the converter’s full-scale range. Especially in multichannel applications, the use of a common external reference has the benefit of obtaining better matching of the full-scale range between converters. The reference buffers can be utilized to supply up to 1mA (sink and source) to external circuitry. The resistor ladder of the ADS824 is divided into several segments and has two additional nodes, ByT and ByB, which are brought out for external bypassing only (Figure 6). To ensure proper operation with any reference configurations, it is necessary to provide solid bypassing at all reference pins in order to keep the clock feedthrough to a minimum. All bypassing capacitors should be located as close to their respective pins as possible. ADS824 REFT +3.5V R1 1.0kΩ 0.1µF The external references can vary as long as the value of the external top reference REFTEXT stays within the range of (VS – 1.25V) and (REFB + 0.8V), and the external bottom reference REFBEXT stays within 1.25V and (REFT – 0.8V). See Figure 8. DIGITAL INPUTS AND OUTPUTS Clock Input Requirements Clock jitter is critical to the SNR performance of high speed, high resolution A/D converters. Clock jitter leads to aperture jitter (tA), which adds noise to the signal being converted. The ADS824 samples the input signal on the rising edge of the CLK input. Therefore, this edge should have the lowest possible jitter. The jitter noise contribution to total SNR is REFB +1.5V R2 1.0kΩ 0.1µF CMV +2.5V FIGURE 7. Alternative Circuit to Generate CM Voltage. +5V B A - Short for 1Vp-p Input Range B - Short for 2Vp-p Input Range (Default) +VS VIN A RSEL INT/EXT GND IN ADS824 CMV +2.5VDC IN REFT External Top Reference REFT = REFB +0.8V to +3.75V ByT GND 4 x 0.1µF || 2.2µF ByB REFB External Bottom Reference REFB = REFT –0.8V to +1.25V FIGURE 8. Configuration Example for External Reference Operation. ADS824 SBAS076A 11 given by the following equation. If this value is near your system requirements, input clock jitter must be reduced. Jitter SNR = 20 log 1 rms signal to rms noise 2 π ƒ IN t A where: ƒIN is input signal frequency tA is rms clock jitter Special consideration should be given to clock jitter, particularly in undersampling applications. The clock input should be treated as an analog input in order to achieve the highest level of performance. Any overshoot or undershoot of the clock signal may cause degradation of performance. When digitizing at high sampling rates, the clock should have 50% duty cycle (tH = tL), along with fast rise and fall times of 2ns or less. Digital Outputs The output data format of the ADS824 is in positive Straight Offset Binary code, see Tables I and II. This format can easily be converted into the Binary Two’s Complement code by inverting the MSB. It is recommended to keep the capacitive loading on the data lines as low as possible (≤ 15pF). Higher capacitive loading will cause larger dynamic currents as the digital outputs are changing. Those high current surges can feed back to the analog portion of the ADS824 and affect the performance. If necessary, external buffers or latches close to the converter’s output pins may be used to minimize the capacitive loading. They also provide the added benefit of isolating the ADS824 from any digital noise activities on the bus coupling back high frequency noise. SINGLE-ENDED INPUT (IN = CMV) +FS –1LSB (IN = REFT) +1/2 Full Scale Bipolar Zero (IN = CMV) –1/2 Full Scale –FS (IN = REFB) STRAIGHT OFFSET BINARY (SOB) 11 11 10 01 00 1111 0000 0000 0000 0000 1111 0000 0000 0000 0000 TABLE I. Coding Table for Single-Ended Input Configuration with IN Tied to the Common-Mode Voltage (CMV). DIFFERENTIAL INPUT +FS –1LSB (IN = +3V, IN = +2V) +1/2 Full Scale Bipolar Zero (IN = IN = CMV) –1/2 Full Scale –FS (IN = +2V, IN = +3V) +5V or +3V, the ADS824 produces corresponding logic levels and can directly interface to the selected logic family. The output stages are designed to supply sufficient current to drive a variety of logic families. However, it is recommended to use the ADS824 with +3V logic supply. This will lower the power dissipation in the output stages due to the lower output swing and reduce current glitches on the supply line, which may affect the ac performance of the converter. In some applications, it might be advantageous to decouple the VDRV pin with additional capacitors or a pi-filter. GROUNDING AND DECOUPLING Proper grounding and bypassing, short lead length, and the use of ground planes are particularly important for high frequency designs. Multilayer PC boards are recommended for best performance since they offer distinct advantages like minimizing ground impedance, separation of signal layers by ground layers, etc. The ADS824 should be treated as an analog component. Whenever possible, the supply pins should be powered by the analog supply. This will ensure the most consistent results since digital supply lines often carry high levels of noise which otherwise would be coupled into the converter and degrade the achievable performance. All ground connections on the ADS824 are internally joined together, obviating the design of split ground planes. The ground pins (1, 16, 26) should directly connect to an analog ground plane, which covers the PC board area around the converter. While designing the layout, it is important to keep the analog signal traces separated from any digital lines to prevent noise coupling onto the analog signal path. Because of its high sampling rate the, ADS824 generates high frequency current transients and noise (clock feedthrough) that are fed back into the supply and reference lines. This requires that all supply and reference pins be sufficiently bypassed. Figure 9 shows the recommended decoupling scheme for the ADS824. In most cases, 0.1µF ceramic chip capacitors at each pin are adequate to keep the impedance low over a wide frequency range. Their effectiveness largely depends on the proximity to the individual supply pin. Therefore, they should be located as close to the supply pins as possible. In addition, a larger bipolar capacitor (1µF to 22µF) should be placed on the PC board in proximity of the converter circuit. STRAIGHT OFFSET BINARY (SOB) 11 11 10 01 00 1111 0000 0000 0000 0000 1111 0000 0000 0000 0000 ADS824 +VS 27 GND 26 +VS 15 0.1µF GND 16 0.1µF VDRV 28 0.1µF 10µF + TABLE II. Coding Table for Differential Input Configuration and 2Vp-p Full-Scale Range. +5V Digital Output Driver (VDRV) The ADS824 features a dedicated supply pin for the output logic drivers, VDRV, which is not internally connected to the other supply pins. By setting the voltage at VDRV to 12 +3/+5V FIGURE 9. Recommended Bypassing for the Supply Pins. ADS824 SBAS076A IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. Customers are responsible for their applications using TI components. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, license, warranty or endorsement thereof. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations and notices. Representation or reproduction of this information with alteration voids all warranties provided for an associated TI product or service, is an unfair and deceptive business practice, and TI is not responsible nor liable for any such use. Resale of TI’s products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service, is an unfair and deceptive business practice, and TI is not responsible nor liable for any such use. Also see: Standard Terms and Conditions of Sale for Semiconductor Products. www.ti.com/sc/docs/stdterms.htm Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2001, Texas Instruments Incorporated