DS2188 T1/CEPT Jitter Attenuator www.dalsemi.com FEATURES PIN ASSIGNMENT Attenuates clock and data jitter present in T1 or CEPT lines Meets the jitter attenuation templates outlined in TR62411, TR-TSY-000170, G.735, and G.742 Only one external component required; either a 6.176 MHz (T1) or 8.192 MHz (CEPT) crystal Selectable buffer size of 128 or 32 bits Jitter attenuation is easily disabled Single +5V supply; low-power CMOS technology Available in 16-pin DIP and 16-pin SOIC (DS2188S) Companion to the DS2186 Transmit Line and DS2187 Receive Line Interface DJA 1 16 VDD RPOS 2 15 RRPOS RNEG 3 14 RRNEG RCLK 4 13 RRCLK BDS 5 12 RST TEST 6 11 BL XTAL OUT 7 10 XTAL2 VSS 8 9 XTAL1 ORDERING INFORMATION DS2188 DS2188S DS2188N DS2188SN 16 Pin dip 16 Pin SOIC 16 Pin dip 16 Pin SOIC (0ºC-F70ºC) (0º-+70ºC) (-40ºC-+85ºC) (-40ºC-+85-ºC) DESCRIPTION The DS2188 T1/CEPT Jitter Attenuator Chip contains a 128 X 2-bit buffer which, in conjunction with an external 4X crystal, is used to attenuate the incoming jitter present in clock and data. The device meets all of the latest applicable specifications including those outlined in TR 62411 (Accunet* T1.5 Service Description and Interface Specifications, December 1990), TR-TSY-000170 (Digital Cross-Connect System Requirements and Objectives, November 1985), and the CCITT Recommendations G.735 and G.742. The DS2188 is compatible with the DS2180A T1/ISDN Primary Rate Transceiver and DS2181A CEPT Transceiver and is the companion to the DS2187 T1/CEPT Receive Line Interface and DS2186 T1/CEPT Transmit Line Interface. It can also be used in conjunction with the DS2190 T1 Network Interface Unit. OVERVIEW The RCLK input is fed to a 128 x 2-bit FIFO where it drives the write pointer for the positive (RPOS) and negative (RNEG) data. The read pointer of the FIFO and RRCLK is generated by dividing the frequency of the crystal connected to XTAL1 and XTAL2 by four. The frequency of the crystal is adjusted by a DPLL to the long-term average frequency of RCLK. As long as the jitter present at RCLK is less than 120 unit intervals peak-to-peak (UIpp), then the FIFO buffer will be able to absorb the incoming jitter and it will be attenuated in accordance with TR 62411 (December 1990). In this situation, the BL (Buffer Limit) pin will remain low. Figures 1 and 2 illustrate the DS2188 Jitter Attenuator performance. If the incoming jitter has excursions greater than 120 UIpp, then the crystal is adjusted to track the shortterm frequency variations of the incoming signal so that there is no loss of data. This adjustment is accomplished by dividing the 4X crystal by either 3 ½ or 4 ½ instead of 4. When the incoming jitter is 1 of 10 100600 DS2188 greater than 120 UIpp, the BL pin will transition high. When the incoming jitter returns to less than 120 UIpp, the BL pin will return low. The jitter attenuator in the DS2188 can be disabled by tying the DJA pin high. When the jitter attenuator is disabled, the FIFO is bypassed and jitter received at RCLK, RPOS and RNEG is passed through the DS2188 to RRCLK, RRPOS, and RRNEG. In this situation, the BL pin has no significance and XTAL OUT will not be coherent with RRCLK. How to use the DS2188 with Dallas Semiconductor’s other T1 and CEPT line interface parts is illustrated in Figures 3 through 5. Figure 3 illustrates how to use the DS2188 in the receive path along with a DS2187 Receive Line Interface. Figure 4 illustrates how to use the DS2188 in the transmit path with the DS2186 Transmit Line Interface. BUFFER DEPTH SELECT The buffer size on the DS2188 can be configured to either 128 or 32 bits via the BDS pin. If BDS is tied low, then the buffer depth will be 128 bits and hence can handle input jitter up to 120 UIpp without losing its full attenuation capabilities as is described above in the Over-view. If BDS is tied high, then the buffer depth is shortened to 32 bits. In this configuration, the DS2188 can handle input jitter up to 28 UIpp without losing its full jitter attenuation capabilities. The user may wish to limit the buffer size to 32 bits in applications where through-put delay is critical or into existing applications that al-ready have 32 bits of buffer space. RESET The buffer on the DS2188 is automatically centered on power-up. The user can recenter the 128-bit (or 32-bit) buffer on demand via the RST pin. The RST pin on the DS2188 is negative-edge triggered. When this pin transitions from high-to-low, the buffer is recentered. The RST pin can be held either high or low during operation of the DS2188; only a negative going signal will initiate a recentering. In most cases, a reset of the DS2188 will corrupt data that is currently passing through the buffer. DS2188 TI JITTER ATTENUATION PERFORMANCE Figure 1 2 of 10 DS2188 DS2188 CEPT JITTER ATTENUATION PERFORMANCE Figure 2 DS2188 IN THE RECEIVE PATH Figure 3 DS2188 IN THE TRANSMIT PATH Figure 4 3 of 10 DS2188 PIN DESCRIPTION Table 1 PIN SYMBOL 1 DJA 2 RPOS 3 RNEG 4 5 RCLK BDS 6 TEST 7 8 9 10 XTAL OUT VSS XTAL1 XTAL2 11 BL 12 RST 13 14 RRCLK RRNEG 15 RRPOS 16 VDD TYPE DESCRIPTION Disable Jitter Attenuation. When high, jittered data and clock at RPOS, I RNEG, and RCLK are passed directly to RRPOS, RRNEG, and RRCLK. Receive Positive Data Input. Jittered data input. Sampled on the falling I edge of RCLK. I Receive Negative Data Input. Jittered data input. Sampled on the falling edge of RCLK. I Receive Clock Input. Jittered input 1.544 MHz or 2.048 MHz clock. Buffer Depth Select. I 0 = 128 bits 1 = 32 bits I Test Input. In normal applications, this pin should be tied low. When tied high, used to verify free running frequency of XTAL. O Crystal Frequency Output. Buffered output of the 4X crystal connected to XTAL1 and XTAL2. Ground. 0.0V I Crystal Connections. In T1 environments, connect a 6.176 MHz crystal to these pins. In CEPT environments, connect an 8.192 MHz crystal to O these pins. Buffer Limit. Transitions high when the buffer fills or empties to within O either 4 bits (BDS=0) or 2 bits (BDS=1) of its capacity. Indicates that the jitter at RCLK is greater than 120 UIpp (BDS=0) or 28 UIpp (BDS=1). Reset. Negative-edge triggered; a high-low transition will recenter the I buffer. Activation of this pin may corrupt data through the DS2188. O Receive Reference Clock. Dejittered 1.544 MHz or 2.048 MHz clock. Receive Reference Negative Data Output. Dejittered data output. O Updated on the rising edge of RRCLK. Receive Reference Positive Data Output. Dejittered data output. O Updated on the rising edge of RRCLK. Positive Supply. 5.0V CRYSTAL REQUIREMENTS The DS2188 must have a crystal connected to the XTAL1 and XTAL2 pins. For T1 environments, the frequency of this crystal should be 6.176 MHz. For CEPT environments, the frequency of this crystal should be 8.192 MHz. Table 2 lists some suggested crystal manufacturers that are recommended for use with the DS2188. Also, see DS2188 Application Note, “Operation at Speeds Greater than E1” for additional information. CRYSTAL MANUFACTURERS Table 2 MANUFACTURER JAN Crystal M-TRON PART # 6323-00, JC6A14 6323-00, JC8A14 4575-002 4575-001 4 of 10 FREQUENCY 6.176 MHz 8.192 MHz 6.176 MHz 8.192 MHz DS2188 CRYSTAL SELECTION GUIDELINES FOR THE DS2188 PARAMETER Parallel resonant frequency Mode Load capacitance Tolerance Pullability Effective series resistance Crystal cut SPECIFICATION 6.176 MHz (T1) or 8.192 MHz (CEPT) Fundamental 14 to 20 pF (16 pF preferred) ±50 ppm over 0 to 70°C CL = 10 pF, delta_f = +175 to +250 ppm CL = 45 pF, delta_f = -175 to -250 ppm 40 ohms maximum for 6.176 MHz 30 ohms maximum for 8.192 MHz AT 5 of 10 DS2188 ABSOLUTE MAXIMUM RATINGS* Voltage on Any Pin Relative to Ground Operating Temperature Storage Temperature Soldering Temperature -0.1V to +7.0V 0° to 70°C -55°C to +125°C See J-STD-020A Specification * This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. RECOMMENDED DC OPERATING CONDITIONS PARAMETER SYMBOL MIN Input Logic 1 VIH Input Logic 0 Supply TYP Commercial (0°C to 70°C) Industrial (-40ºC to 85ºC) MAX UNITS NOTES 2.0 VCC+0.3 V 1 VIL -0.3 +0.8 V 1 VDD 4.50 5.50 V NOTE: 1. Does not apply to XTAL1. CAPACITANCE PARAMETER Input Capacitance Output (tA=25°C) SYMBOL MIN TYP MAX UNITS CIN 5 pF COUT 10 pF NOTES DC ELECTRICAL CHARACTERISTICS Commercial (0°C to 70°C; VDD = 5.0V ± 10%) Industrial (-40ºC to 85ºC) PARAMETER SYMBOL MIN TYP MAX UNITS NOTES 7 12 mA 1 +1.0 µA 2, 3 Supply Current IDD Input Leakage IL -1.0 Output Current (2.4V) IOH -1.0 mA 3 Output Current (0.4V) IOL +4.0 mA 3 NOTES: 1. RCLK = 1.544 MHz; VDD = 5.50; outputs open. 2. VSS < VIN < VDD: XTAL1 = XTAL2 = VDD. 3. Does not apply to XTAL1 or XTAL2. 6 of 10 DS2188 AC ELECTRICAL CHARACTERISTICS Commercial (0°C to 70°C; VDD = 5.0V ± 0%) Industrial (-40ºC to 85ºC) PARAMETER SYMBOL MIN RCLK Period -200 RCLK Pulse Width 100 RCLK Rise and Fall Times TYP MAX UNITS NOTES +200 ppm 1 ns 50 ns RPOS, RNEG Setup to RCLK 50 ns RPOS, RNEG Hold for RCLK 50 ns Propagation delay from RRCLK to RPOS, RRNEG Valid 50 ns Propagation delay from XTAL OUT to RRCLK 50 ns RST Pulse Width 1 NOTES: 2 µA 1. The average period of RCLK must be within Ù200 ppm of the fundamental frequency of the crystal divided by four. 2. Only valid when the incoming jitter is less than 120 Ulpp (BDS=0) or 28 Ulpp (BDS=1). 7 of 10 DS2188 AC TIMING DIAGRAM Figure 5 NOTE: 1. The phase relationship between XTAL OUT and RRCLK can be of either form. 8 of 10 DS2188 DS1288 T1/CEPT JITTER ATTENTUATOR 16-PIN DIP PKG DIM AIN MM B IN MM C IN MM D IN MM E IN MM F IN MM G IN MM H IN MM J IN MM K IN MM 16-PIN MIN MAX 0.740 0.780 18.80 19.81 0.240 0.260 6.10 6.60 0.120 0.140 3.05 3.56 0.300 0.325 7.62 8.26 0.015 0.040 0.38 1.02 0.120 0.140 3.04 1.02 0.090 0.110 2.29 2.79 0.320 0.370 8.13 9.40 0.008 0.012 0.20 0.30 0.015 0.021 0.38 0.53 9 of 10 DS2188 DS1288S T1/CEPT JITTER ATTENTUATOR 16-PIN SOIC PKG DIM AIN MM B IN MM C IN MM E IN MM F IN MM G IN MM H IN MM J IN MM K IN MM L IN MM phi 16-PIN MIN MAX 0.402 0.412 10.21 10.46 0.290 0.300 7.37 7.65 0.089 0.095 2.26 2.41 0.004 0.012 0.102 0.30 0.094 0.105 2.38 2.68 0.050 BSC 1.27 BSC 0.398 0.416 10.11 10.57 0.009 0.013 0.229 0.33 0.013 0.019 0.33 0.48 0.016 0.40 0.40 1.02 0Û 8Û 10 of 10