Precision ±1.7 g Single-/Dual-Axis i MEMS® Accelerometer ADXL204 FEATURES GENERAL DESCRIPTION High performance, dual-axis accelerometer on a single IC chip Specified at VS = 3.3 V 5 mm × 5 mm × 2 mm LCC package Better than 2 mg resolution at 60 Hz Low power: 500 μA at VS = 3.3 V (typical) High zero g bias stability High sensitivity accuracy –40°C to +125°C temperature range X-axis and Y-axis aligned to within 0.1° (typical) BW adjustment with a single capacitor Single-supply operation 3500 g shock survival RoHS compliant Compatible with Sn/Pb- and Pb-free solder processes The ADXL204 is a high precision, low power, complete dualaxis accelerometer with signal-conditioned voltage outputs, all on a single monolithic IC. Like the ADXL203, it measures acceleration with a full-scale range of ±1.7 g; however, the ADXL204 is tested and specified for 3.3 V supply voltage, whereas the ADXL203 is tested and specified at 5 V. Both parts function well over a wide 3 V to 6 V operating voltage range. The ADXL204 can measure both dynamic acceleration (for example, vibration) and static acceleration (for example, gravity). The typical noise floor is 170 μg/√Hz, allowing signals below 2 mg (0.1° of inclination) to be resolved in tilt sensing applications using narrow bandwidths (<60 Hz). The user selects the bandwidth of the accelerometer using Capacitor CX and Capacitor CY at the XOUT and YOUT pins. Bandwidths of 0.5 Hz to 2.5 kHz can be selected to suit the application. APPLICATIONS Vehicle dynamic control (VDC)/electronic stability program (ESP) systems Electronic chassis controls Electronic braking Platform stabilization/leveling Navigation Alarms and motion detectors High accuracy, 2-axis tilt sensing The ADXL204 is available in a 5 mm × 5 mm × 2 mm, 8-terminal hermetic LCC package. FUNCTIONAL BLOCK DIAGRAM +5V VS ADXL204 CDC AC AMP DEMOD OUTPUT AMP OUTPUT AMP SENSOR COM ST RFILT 32kΩ YOUT XOUT CY CX 05512-001 RFILT 32kΩ Figure 1. Rev. A Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2006 Analog Devices, Inc. All rights reserved. ADXL204 TABLE OF CONTENTS Features .............................................................................................. 1 Applications..................................................................................... 10 Applications....................................................................................... 1 Power Supply Decoupling ......................................................... 10 General Description ......................................................................... 1 Setting the Bandwidth Using CX and CY ................................. 10 Functional Block Diagram .............................................................. 1 Self Test ........................................................................................ 10 Revision History ............................................................................... 2 Design Trade-Offs for Selecting Filter Characteristics: The Noise/BW Trade-Off.................................................................. 10 Specifications..................................................................................... 3 Absolute Maximum Ratings............................................................ 4 Using the ADXL204 with Operating Voltages Other than 3.3 V .......................................................................... 11 ESD Caution.................................................................................. 4 Using the ADXL204 as a Dual-Axis Tilt Sensor ........................ 11 Pin Configuration and Function Descriptions............................. 5 Outline Dimensions ....................................................................... 12 Typical Performance Characteristics ............................................. 6 Ordering Guide .......................................................................... 12 Theory of Operation ........................................................................ 9 Performance .................................................................................. 9 REVISION HISTORY 3/06—Rev. 0 to Rev. A Changes to Format .............................................................Universal Changes to Product Title, Features, and General Description ... 1 Changes to Table 1............................................................................ 3 Changes to Table 2............................................................................ 4 Added Figure 2 and Table 4............................................................. 4 Changes to Figure 3.......................................................................... 5 Changes to Figure 11 and Figure 14............................................... 7 Changes to Table 7.......................................................................... 10 4/05—Revision 0: Initial Version Rev. A | Page 2 of 12 ADXL204 SPECIFICATIONS All minimum and maximum specifications are guaranteed. Typical specifications are not guaranteed. TA = –40°C to +125°C; VS = 3.3 V; CX = CY = 0.1 μF; acceleration = 0 g, unless otherwise noted. Table 1. Parameter SENSOR INPUT Measurement Range 1 Nonlinearity Package Alignment Error Alignment Error Cross Axis Sensitivity SENSITIVITY (RATIOMETRIC) 2 Sensitivity at XOUT, YOUT Sensitivity Change due to Temperature 3 ZERO g BIAS LEVEL (RATIOMETRIC) 0 g Voltage at XOUT, YOUT Initial 0 g Output Deviation from Ideal 0 g Offset vs. Temperature NOISE PERFORMANCE Output Noise Noise Density FREQUENCY RESPONSE 4 CX, CY Range 5 RFILT Tolerance Sensor Resonant Frequency SELF TEST 6 Logic Input Low Logic Input High ST Input Resistance to Ground Output Change at XOUT, YOUT OUTPUT AMPLIFIER Output Swing Low Output Swing High POWER SUPPLY Operating Voltage Range Quiescent Supply Current Turn-On Time 7 Conditions Each axis Min Typ Max ±0.2 ±1 ±0.1 ±1.5 ±1.25 ±1.7 % of full scale X sensor to Y sensor Each axis VS = 3.3 V VS = 3.3 V Each axis VS = 3.3 V VS = 3.3 V, 25°C ±3 Unit g % Degrees Degrees % 595 620 ±0.3 645 mV/g % 1.55 1.65 ±50 ±0.15 1.75 V mg mg/°C 1 170 3 mV rms μg/√Hz rms 10 40 μF kΩ kHz 0.66 <4 kHz, VS = 3.3 V 0.002 24 32 5.5 ±0.8 T Self test 0 to 1 No load No load 2.64 30 100 0.05 50 200 300 V V kΩ mV 0.2 2.9 3.1 V V 3 0.5 20 1 6 0.9 V mA ms Guaranteed by measurement of initial offset and sensitivity. Sensitivity is essentially ratiometric to VS. For VS = 3.0 V to 3.6 V, sensitivity is typically 185 mV/V/g to 190 mV/V/g. 3 Defined as the change from ambient-to-maximum temperature or ambient-to-minimum temperature. 4 Actual frequency response controlled by user-supplied external capacitor (CX, CY). 5 Bandwidth = 1/(2 × π × 32 kΩ × C). For CX, CY = 0.002 μF, bandwidth = 2500 Hz. For CX, CY = 10 μF, bandwidth = 0.5 Hz. Minimum/maximum values are not tested. 6 Self-test response changes cubically with VS. 7 Larger values of CX, CY increase turn-on time. Turn-on time is approximately 160 × CX or CY + 4 ms, where CX, CY are in μF. 2 Rev. A | Page 3 of 12 ADXL204 ABSOLUTE MAXIMUM RATINGS Table 2. Parameter Acceleration (Any Axis, Unpowered) Acceleration (Any Axis, Powered) Drop Test (Concrete Surface) VS All Other Pins Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Rating 3500 g 3500 g 1.2 m −0.3 V to +7.0 V (COM − 0.3 V) to (VS + 0.3 V) Indefinite Output Short-Circuit Duration (Any Pin to Common) Temperature Range (Powered) Temperature Range (Storage) Table 3. Package Characteristics Package Type 8-Terminal LCC −55°C to +125°C −65°C to +150°C θJC 20°C/W Device Weight <1.0 gram CRITICAL ZONE TL TO TP tP TP θJA 120°C/W TEMPERATURE RAMP-UP TL tL TSMAX TSMIN tS RAMP-DOWN 05512-002 PREHEAT t25°C TO PEAK TIME Figure 2. Recommended Soldering Profile Table 4. Profile Feature AVERAGE RAMP RATE (TL TO TP) PREHEAT Minimum Temperature (TSMIN) Minimum Temperature (TSMAX) Time (TSMIN to TSMAX) (tS) TSMAX TO TL Ramp-Up Rate TIME MAINTAINED ABOVE LIQUIDOUS (TL) Liquidous Temperature (TL) Time (tL) PEAK TEMPERATURE (TP) TIME WITHIN 5°C OF ACTUAL PEAK TEMPERATURE (tP) RAMP-DOWN RATE TIME 25°C TO PEAK TEMPERATURE Sn63/Pb37 3°C/sec maximum Condition Pb-Free 3°C/sec maximum 100°C 150°C 60 sec to 120 sec 150°C 200°C 60 sec to 150 sec 3°C/sec 3°C/sec 183°C 60 sec to 150 sec 240°C +0°C/–5°C 10 sec to 30 sec 6°C/sec maximum 6 minutes maximum 217°C 60 sec to 150 sec 260°C +0°C/–5°C 20 sec to 40 sec 6°C/sec maximum 8 minutes maximum ESD CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Rev. A | Page 4 of 12 ADXL204 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS ADXL204E TOP VIEW (Not to Scale) VS 7 XOUT DNC 2 6 YOUT 5 DNC COM 3 +Y +X 4 DNC 05512-022 8 ST 1 Figure 3. Pin Configuration Table 5. Pin Function Descriptions Pin No. 1 2 3 4 5 6 7 8 Mnemonic ST DNC COM DNC DNC YOUT XOUT VS Description Self Test Do Not Connect Common Do Not Connect Do Not Connect Y Channel Output X Channel Output 3 V to 6 V Rev. A | Page 5 of 12 0.655 0.649 0.644 0.638 0.633 0.627 0.621 10 Figure 6. X-Axis Sensitivity at 25°C V/g Rev. A | Page 6 of 12 05512-008 0 Figure 9. Y-Axis Sensitivity at 25°C V/g 0.655 10 0.649 20 0.644 30 0.638 50 0.633 60 0.627 mg/°C 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 05512-007 0 0.621 Figure 5. X-Axis Zero g Bias Temperature Coefficient –0.1 5 0.616 VOLTS (V) 0.610 10 –0.2 15 –0.3 20 0.605 20 –0.4 25 0.599 Figure 4. X-Axis Zero g Bias Output at 25°C 0.594 1.749 1.727 1.705 1.683 1.661 1.639 1.617 1.595 5 05512-006 0 1.573 10 –0.5 15 –0.6 20 0.588 30 1.551 25 PERCENT OF POPULATION (%) 30 0.583 05512-003 35 –0.7 25 PERCENT OF POPULATION (%) 1.749 5 –0.8 05512-004 1.727 1.705 1.683 1.661 1.639 1.617 1.595 1.573 1.551 PERCENT OF POPULATION (%) 35 0.577 40 PERCENT OF POPULATION (%) 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 –0.1 –0.2 –0.3 –0.4 –0.5 –0.6 0 0.616 0.610 0.605 0.599 0.594 0.588 0.583 05512-005 0 –0.7 –0.8 PERCENT OF POPULATION (%) 0 0.577 PERCENT OF POPULATION (%) ADXL204 TYPICAL PERFORMANCE CHARACTERISTICS VS = 3.3 V for all graphs, unless otherwise noted. 25 20 15 10 Figure 7. Y-Axis Zero g Bias Output at 25°C VOLTS (V) 15 10 5 Figure 8. Y-Axis Zero g Bias Temperature Coefficient mg/°C 70 60 50 40 30 20 ADXL204 1.710 0.65 1.698 0.64 1.686 0.63 SENSITIVITY (V/g) 1.662 1.650 1.638 1.626 0.62 0.61 1.614 45 50 40 45 30 25 20 15 10 05512-010 0 170 180 190 200 130 140 150 160 PERCENT OF POPULATION (%) 30 25 20 15 10 130 120 110 90 80 100 200 210 30 25 20 15 10 PERCENT SENSITIVITY (%) 05512-014 PERCENT SENSITIVITY (%) Figure 12. Z vs. X Cross-Axis Sensitivity Figure 15. Z vs. Y Cross-Axis Sensitivity Rev. A | Page 7 of 12 5.0 –1.0 –2.0 –3.0 –4.0 –5.0 0 5.0 4.0 3.0 2.0 1.0 0 190 5 05512-011 5 –1.0 180 Figure 14. Y-Axis Noise Density at 25°C 35 –2.0 170 µg/ Hz 35 –3.0 70 05512-012 120 40 –4.0 60 0 210 40 –5.0 50 5 Figure 11. X-Axis Noise Density at 25°C PERCENT OF POPULATION (%) 40 10 µg/ Hz 0 30 20 0 –10 –20 15 4.0 160 20 3.0 150 25 2.0 140 30 1.0 130 34 0 120 40 05512-013 34 5 TEMPERATURE (°C) Figure 13. Sensitivity vs. Temperature—Parts Soldered to PCB PERCENT OF POPULATION (%) PERCENT OF POPULATION (%) Figure 10. Zero g Bias vs. Temperature—Parts Soldered to PCB –30 –50 0.58 130 120 110 90 TEMPERATURE (°C) 100 80 70 60 50 40 30 20 0 10 –10 –20 –30 –40 –50 1.590 10 05512-009 0.60 1.602 –40 VOLTAGE (1V/g) 1.674 ADXL204 0.9 100 90 PERCENT OF POPULATION (%) VS = 5V 0.6 0.5 VS = 3V 05512-015 0.4 30 20 10 1000 900 800 700 0 150 600 100 40 500 50 TEMPERATURE (°C) 50 400 0 60 200 0.3 –50 3V 70 300 CURRENT (mA) 0.7 5V 80 05512-018 0.8 (µA) Figure 19. Supply Current at 25°C Figure 16. Supply Current vs. Temperature 30 35 PERCENT OF POPULATION (%) 25 20 15 10 15 10 05512-019 0.269 0.256 0.242 0.229 0.216 0.202 0.189 0.175 0.162 0.148 0 0.269 0.256 0.242 0.229 0.216 0.202 0.189 0.175 0.162 0.148 0.135 0 20 5 05512-016 5 25 0.135 PERCENT OF POPULATION (%) 30 VOLTS (V) VOLTS (V) Figure 20. Y-Axis Self-Test Response at 25°C Figure 17. X-Axis Self-Test Response at 25°C 0.32 0.29 0.23 0.20 0.17 0.14 05512-020 130 120 110 90 100 TEMPERATURE (°C) 80 70 60 50 40 30 20 10 –10 –20 –30 –50 0.08 0 05512-017 0.11 –40 VOLTAGE (1V/g) 0.26 Figure 18. Self-Test Response vs. Temperature Figure 21. Turn-On Time—CX, CY = 0.1 μF, Time Scale = 2 ms/DIV Rev. A | Page 8 of 12 ADXL204 THEORY OF OPERATION PIN 8 XOUT = 1.03V YOUT = 1.65V PIN 8 XOUT = 1.65V YOUT = 1.03V TOP VIEW (Not to Scale) XOUT = 1.65V YOUT = 1.65V PIN 8 XOUT = 2.27V YOUT = 1.65V EARTH'S SURFACE 05512-021 PIN 8 XOUT = 1.65V YOUT = 2.27V Figure 22. Output Response vs. Orientation The ADXL204 is a complete acceleration measurement system on a single monolithic IC. The ADXL204 is a dual-axis accelerometer. It contains a polysilicon surface-micromachined sensor and signal conditioning circuitry to implement an open-loop acceleration measurement architecture. The output signals are analog voltages proportional to acceleration. The ADXL204 is capable of measuring both positive and negative accelerations to at least ±1.7 g. The accelerometer can measure static acceleration forces, such as gravity, allowing it to be used as a tilt sensor. The sensor is a surface-micromachined polysilicon structure built on top of the silicon wafer. Polysilicon springs suspend the structure over the surface of the wafer and provide a resistance against acceleration forces. Deflection of the structure is measured using a differential capacitor that consists of independent fixed plates and plates attached to the moving mass. The fixed plates are driven by 180° out-of-phase square waves. Acceleration deflects the beam and unbalances the differential capacitor, resulting in an output square wave whose amplitude is proportional to acceleration. Phase-sensitive demodulation techniques are then used to rectify the signal and determine the direction of the acceleration. PERFORMANCE Rather than using additional temperature compensation circuitry, innovative design techniques have been used to ensure high performance is built in. As a result, there is essentially no quantization error or nonmonotonic behavior, and temperature hysteresis is very low, typically less than 10 mg over the –40°C to +125°C temperature range. Figure 10 shows the zero g output performance of eight parts (X-axis and Y-axis) over a –40°C to +125°C temperature range. Figure 13 demonstrates the typical sensitivity shift over temperature for VS = 3.3 V. Sensitivity stability is typically better than ±1% over temperature. The output of the demodulator is amplified and brought offchip through a 32 kΩ resistor. At this point, the user can set the signal bandwidth of the device by adding a capacitor. This filtering improves measurement resolution and helps prevent aliasing. Rev. A | Page 9 of 12 ADXL204 APPLICATIONS POWER SUPPLY DECOUPLING For most applications, a single 0.1 μF capacitor, CDC, adequately decouples the accelerometer from noise on the power supply. However in some cases, particularly where noise is present at the 140 kHz internal clock frequency (or any harmonic thereof), noise on the supply can cause interference on the ADXL204 output. If additional decoupling is needed, a 100 Ω, or smaller, resistor or ferrite bead can be inserted in the supply line of the ADXL204. Additionally, a larger bulk bypass capacitor, in the 1 μF to 22 μF range, can be added in parallel to CDC. SETTING THE BANDWIDTH USING CX AND CY The ADXL204 has provisions for bandlimiting the XOUT and YOUT pins. Capacitors must be added at these pins to implement low-pass filtering for antialiasing and noise reduction. The equation for the 3 dB bandwidth is F–3 dB = 1/(2π(32 kΩ) × C(X, Y)) or more simply, F–3 dB = 5 μF/C(X, Y) The tolerance of the internal resistor (RFILT) can vary typically as much as ±25% of its nominal value (32 kΩ); thus, the bandwidth varies accordingly. A minimum capacitance of 2000 pF for CX and CY is required in all cases. Table 6. Filter Capacitor Selection, CX and CY Bandwidth (Hz) 1 10 50 100 200 500 DESIGN TRADE-OFFS FOR SELECTING FILTER CHARACTERISTICS: THE NOISE/BW TRADE-OFF The accelerometer bandwidth selected ultimately determines the measurement resolution (smallest detectable acceleration). Filtering can be used to lower the noise floor, which improves the resolution of the accelerometer. Resolution is dependent on the analog filter bandwidth at XOUT and YOUT. The output of the ADXL204 has a typical bandwidth of 2.5 kHz. The user must filter the signal at this point to limit aliasing errors. The analog bandwidth must be no more than half the A/D sampling frequency to minimize aliasing. The analog bandwidth can be further decreased to reduce noise and improve resolution. The ADXL204 noise has the characteristics of white Gaussian noise, which contributes equally at all frequencies and is described in terms of μg/√Hz (that is, the noise is proportional to the square root of the accelerometer’s bandwidth). The user should limit bandwidth to the lowest frequency needed by the application to maximize the resolution and dynamic range of the accelerometer. With the single-pole, roll-off characteristic, the typical noise of the ADXL204 is determined by rmsNoise = (170 μg/√Hz) × (√BW×1.6) At 100 Hz the noise is Capacitor (μF) 4.7 0.47 0.10 0.05 0.027 0.01 rmsNoise = (170 μg/√Hz) × (√BW×1.6) = 2.15 mg Often, the peak value of the noise is desired. Peak-to-peak noise can only be estimated by statistical methods. Table 7 is useful for estimating the probabilities of exceeding various peak values, given the rms value. Table 7. Estimation of Peak-to-Peak Noise SELF TEST The ST pin controls the self-test feature. When this pin is set to VS, an electrostatic force is exerted on the beam of the accelerometer. The resulting movement of the beam allows the user to test if the accelerometer is functional. The typical change in output is 325 mg (corresponding to 200 mV). This pin can be left open-circuit or connected to common in normal use. Peak-to-Peak Value 2 × rms 4 × rms 6 × rms 8 × rms The ST pin should never be exposed to voltage greater than VS + 0.3 V. If the system design is such that this condition cannot be guaranteed (that is, multiple supply voltages present), a low VF clamping diode between ST and VS is recommended. Rev. A | Page 10 of 12 % of Time Noise Exceeds Nominal Peak-to-Peak Value 32 4.6 0.27 0.006 ADXL204 Peak-to-peak noise values give the best estimate of the uncertainty in a single measurement and is estimated by 6 × rms. Table 8 gives the typical noise output of the ADXL204 for various CX and CY values. Table 8. Filter Capacitor Selection (CX, CY) Bandwidth(Hz) 10 50 100 500 CX, CY (μF) 0.47 0.1 0.047 0.01 RMS Noise (mg) 0.7 1.5 2.2 4.8 Peak-to-Peak Noise Estimate (mg) 4.1 9.1 12.9 28.8 USING THE ADXL204 WITH OPERATING VOLTAGES OTHER THAN 3.3 V The ADXL204 is tested and specified at VS = 3.3 V; however, it can be powered with VS as low as 3 V or as high as 6 V. Some performance parameters change as the supply voltage is varied. The ADXL204 output is ratiometric, so the output sensitivity, or scale factor, varies proportionally to supply voltage. At VS = 3 V, the output sensitivity is typically 560 mV/g. At VS = 5 V, the output sensitivity is typically 1000 mV/g. USING THE ADXL204 AS A DUAL-AXIS TILT SENSOR One of the most popular applications of the ADXL204 is tilt measurement. An accelerometer uses the force of gravity as an input vector to determine the orientation of an object in space. An accelerometer is most sensitive to tilt when its sensitive axis is perpendicular to the force of gravity, that is, parallel to the earth’s surface. At this orientation, its sensitivity to changes in tilt is highest. When the accelerometer is oriented on axis to gravity, that is, near its +1 g or –1 g reading, the change in output acceleration per degree of tilt is negligible. When the accelerometer is perpendicular to gravity, its output changes nearly 17.5 mg per degree of tilt. At 45°, its output changes at only 12.2 mg per degree and resolution declines. Dual-Axis Tilt Sensor: Converting Acceleration to Tilt When the accelerometer is oriented, so both its x-axis and y-axis are parallel to the earth’s surface, it can be used as a 2-axis tilt sensor with a roll axis and a pitch axis. Once the output signal from the accelerometer is converted to an acceleration that varies between –1 g and +1 g, the output tilt in degrees is calculated as: PITCH = ASIN(AX/1 g) The zero g bias output is also ratiometric, so the zero g output is nominally equal to VS/2 at all supply voltages. The output noise is not ratiometric but is absolute in volts; therefore, the noise density decreases as the supply voltage increases. This is because the scale factor (mV/g) increases while the noise voltage remains constant. At VS = 3 V, the noise density is typically 190 μg/√Hz. At VS = 5 V, the noise density is typically 110 μg/√Hz. ROLL = ASIN(AY/1 g) Be sure to account for overranges. It is possible for the accelerometers to output a signal greater than ±1 g due to vibration, shock, or other accelerations. Self-test response in g is roughly proportional to the square of the supply voltage. However, when ratiometricity of sensitivity is factored in with supply voltage, self-test response in volts is roughly proportional to the cube of the supply voltage. This means at VS = 3 V, the self-test response is approximately equivalent to 150 mV, or equivalent to 270 mg (typical). At VS = 5 V, the self-test response is approximately equivalent to 750 mV, or equivalent to 750 mg (typical). The supply current decreases as the supply voltage decreases. Typical current consumption at VDD = 5 V is 750 μA. Rev. A | Page 11 of 12 ADXL204 OUTLINE DIMENSIONS 5.00 SQ 1.27 1.78 1.27 4.50 SQ 7 0.50 DIAMETER 1 1.90 2.50 TOP VIEW 1.27 0.20 R 0.38 R 0.20 5 3 0.64 2.50 0.38 DIAMETER BOTTOM VIEW Figure 23. 8-Terminal Ceramic Leadless Chip Carrier [LCC] (E-8) Dimensions shown in millimeters ORDERING GUIDE Model ADXL204CE ADXL204CE-REEL ADXL204EB Number of Axes 2 2 Specified Voltage (V) 3.3 3.3 Temperature Range –40°C to +125°C –40°C to +125°C Package Description 8-Terminal Ceramic Leadless Chip Carrier (LCC) 8-Terminal Ceramic Leadless Chip Carrier (LCC) Evaluation Board Package Option E-8 E-8 ©2006 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D05512-0-3/06(A) T T Rev. A | Page 12 of 12