APPLICATIONS Routing of High Speed Signals Including: Composite Video (NTSC, PAL, S, SECAM.) Component Video (YUV, RGB) Compressed Video (MPEG, Wavelet) 3-Level Digital Video (HDB3) PRODUCT DESCRIPTION The AD8108 and AD8109 are high speed 8 × 8 video crosspoint switch matrices. They offer a –3 dB signal bandwidth greater than 250 MHz and channel switch times of less than 25 ns with 1% settling. With –83 dB of crosstalk and –98 dB isolation (@ 5 MHz), the AD8108/AD8109 are useful in many high speed applications. The differential gain and differential FUNCTIONAL BLOCK DIAGRAM SER/PAR D0 D1 D2 D3 A0 A1 CLK DATA IN A2 32-BIT SHIFT REGISTER WITH 4-BIT PARALLEL LOADING UPDATE CE 32 PARALLEL LATCH RESET 32 DECODE 8 3 4:8 DECODERS AD8108/AD8109 64 SWITCH MATRIX 8 INPUTS DATA OUT SET INDIVIDUAL OR RESET ALL OUTPUTS TO "OFF" FEATURES 8 3 8 High Speed Nonblocking Switch Arrays AD8108: G = +1 AD8109: G = +2 Serial or Parallel Programming of Switch Array Serial Data Out Allows “Daisy Chaining” of Multiple 8 3 8s to Create Larger Switch Arrays Output Disable Allows Connection of Multiple Devices Pin Compatible with AD8110/AD8111 16 3 8 Switch Arrays For 16 3 16 Arrays See AD8116 Complete Solution Buffered Inputs Eight Output Amplifiers, AD8108 (G = +1), AD8109 (G = +2) Drives 150 V Loads Excellent Video Performance 60 MHz 0.1 dB Gain Flatness 0.02%/0.028 Differential Gain/Differential Phase Error (RL = 150 V) Excellent AC Performance AD8108 AD8109 –3 dB Bandwidth 325 MHz 250 MHz Slew Rate 400 V/ms 480 V/ms Low Power of 45 mA Low All Hostile Crosstalk of –83 dB @ 5 MHz Reset Pin Allows Disabling of All Outputs (Connected Through a Capacitor to Ground Provides “PowerOn” Reset Capability) Excellent ESD Rating: Exceeds 4000 V Human Body Model 80-Lead TQFP Package (12 mm 3 12 mm) 8 OUTPUT BUFFER G = +1, G = +2 ENABLE/DISABLE a 325 MHz, 8 3 8 Buffered Video Crosspoint Switches AD8108/AD8109* 8 OUTPUTS phase of better than 0.02% and 0.02° respectively along with 0.1 dB flatness out to 60 MHz make the AD8108/AD8109 ideal for video signal switching. The AD8108 and AD8109 include eight independent output buffers that can be placed into a high impedance state for paralleling crosspoint outputs so that off channels do not load the output bus. The AD8108 has a gain of +1, while the AD8109 offers a gain of +2. They operate on voltage supplies of ± 5 V while consuming only 45 mA of idle current. The channel switching is performed via a serial digital control (which can accommodate “daisy chaining” of several devices) or via a parallel control allowing updating of an individual output without re-programing the entire array. The AD8108/AD8109 is packaged in an 80-lead TQFP package and is available over the extended industrial temperature range of –40°C to +85°C. *Patent Pending. REV. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 World Wide Web Site: http://www.analog.com Fax: 781/326-8703 © Analog Devices, Inc., 1997 AD8108/AD8109–SPECIFICATIONS (V = 65 V, T = +258C, R = 1 kV unless otherwise noted) S Parameter DYNAMIC PERFORMANCE –3 dB Bandwidth Propagation Delay Slew Rate Settling Time Gain Flatness NOISE/DISTORTION PERFORMANCE Differential Gain Error Differential Phase Error Crosstalk, All Hostile Off Isolation, Input-Output Input Voltage Noise DC PERFORMANCE Gain Error Gain Matching A Output Disable Capacitance Output Leakage Current Output Voltage Range Output Current Short Circuit Current INPUT CHARACTERISTICS Input Offset Voltage Input Voltage Range Input Capacitance Input Resistance Input Bias Current SWITCHING CHARACTERISTICS Enable On Time Switching Time, 2 V Step Switching Transient (Glitch) POWER SUPPLIES Supply Current Supply Voltage Range PSRR OPERATING TEMPERATURE RANGE Temperature Range θJA AD8108/AD8109 Typ Conditions Min 200 mV p-p, RL = 150 Ω 2 V p-p, RL = 150 Ω 2 V p-p, RL = 150 Ω 2 V Step, RL = 150 Ω 0.1%, 2 V Step, RL = 150 Ω 0.05 dB, 200 mV p-p, RL = 150 Ω 0.05 dB, 2 V p-p, R L = 150 Ω 0.1 dB, 200 mV p-p, RL = 150 Ω 0.1 dB, 2 V p-p, RL = 150 Ω 240/150 Max Units 325/250 140/160 5 400/480 40 60/50 60/50 70/65 80/50 MHz MHz ns V/µs ns MHz MHz MHz MHz NTSC or PAL, RL = 1 kΩ NTSC or PAL, RL = 150 Ω NTSC or PAL, RL = 1 kΩ NTSC or PAL, RL = 150 Ω f = 5 MHz f = 10 MHz f = 10 MHz, RL =150 Ω, One Channel 0.01 MHz to 50 MHz 0.01 0.02 0.01 0.02 83/85 76/83 93/98 15 % % Degrees Degrees dB dB dB nV/√Hz RL = 1 kΩ RL = 150 Ω No Load, Channel-Channel RL = 1 kΩ, Channel-Channel 0.04/0.1 0.15/0.25 DC, Enabled Disabled Disabled Disabled, AD8108 Only No Load ± 2.5 20 Worst Case (All Configurations) Temperature Coefficient Any Switch Configuration Per Output Selected 0.07/0.5 11, 17 6, 12 6, 12 6, 12 6, 12 7, 13 7, 13 22, 28 19, 25 0.2 10/0.001 2 1/NA ±3 40 65 Ω MΩ pF µA V mA mA 23, 29 20, 26 mV µV/°C V pF MΩ µA 34, 40 35, 41 5 12 ± 2.5/± 1.25 ± 3/± 1.5 2.5 1 10 2 20 5 ns ns mV p-p f = 100 kHz f = 1 MHz 33 10 33 10 10 ± 4.5 to ±5.5 73/78 55/58 mA mA mA mA mA V dB dB Operating (Still Air) Operating (Still Air) –40 to +85 48 °C °C/W AVCC, Outputs Enabled, No Load AVCC, Outputs Disabled AVEE, Outputs Enabled, No Load AVEE, Outputs Disabled DVCC 6, 12 6, 12 0.5/8 60 25 20/30 50% UPDATE to 1% Settling Measured at Output Reference Figure No. % % % % ppm/°C 0.02/1.0 0.09/1.0 Gain Temperature Coefficient OUTPUT CHARACTERISTICS Output Impedance L 21, 27 18, 24 Specifications subject to change without notice. –2– REV. 0 AD8108/AD8109 TIMING CHARACTERISTICS (Serial) Parameter Symbol Min Serial Data Setup Time CLK Pulsewidth Serial Data Hold Time CLK Pulse Separation, Serial Mode CLK to UPDATE Delay UPDATE Pulsewidth CLK to DATA OUT Valid, Serial Mode Propagation Delay, UPDATE to Switch On or Off Data Load Time, CLK = 5 MHz, Serial Mode CLK, UPDATE Rise and Fall Times RESET Time t1 t2 t3 t4 t5 t6 t7 – – – – 20 100 20 100 0 50 t2 Limit Typ Max 180 8 6.4 100 200 Units ns ns ns ns ns ns ns ns µs ns ns t4 1 CLK LOAD DATA INTO SERIAL REGISTER ON FALLING EDGE 0 t1 t3 1 DATA IN OUT7 (D3) OUT7 (D2) OUT00 (D0) 0 t6 t5 1 = LATCHED UPDATE 0 = TRANSPARENT TRANSFER DATA FROM SERIAL REGISTER TO PARALLEL LATCHES DURING LOW LEVEL t7 DATA OUT Figure 1. Timing Diagram, Serial Mode Table I. Logic Levels VIH VIL RESET, SER/PAR CLK, DATA IN, CE, UPDATE RESET, SER/PAR CLK, DATA IN, CE, UPDATE 2.0 V min 0.8 V max REV. 0 VOH VOL IIH IIL IOH IOL DATA OUT DATA OUT RESET, SER/PAR CLK, DATA IN, CE, UPDATE RESET, SER/PAR CLK, DATA IN, CE, UPDATE DATA OUT DATA OUT 2.7 V min 0.5 V max 20 µA max –400 µA min –400 µA max 3.0 mA min –3– AD8108/AD8109 TIMING CHARACTERISTICS (Parallel) Limit Parameter Symbol Min Data Setup Time CLK Pulsewidth Data Hold Time CLK Pulse Separation CLK to UPDATE Delay UPDATE Pulsewidth Propagation Delay, UPDATE to Switch On or Off CLK, UPDATE Rise and Fall Times RESET Time t1 t2 t3 t4 t5 t6 – – – 20 100 20 100 0 50 t2 Max Units ns ns ns ns ns ns ns ns ns 8 100 200 t4 1 CLK 0 D0–D3 A0–A2 t1 t3 1 0 t5 t6 1 = LATCHED UPDATE 0 = TRANSPARENT Figure 2. Timing Diagram, Parallel Mode Table II. Logic Levels VIH VIL RESET, SER/PAR CLK, D0, D1, D2, D3, A0, A1, A2 CE, UPDATE RESET, SER/PAR CLK, D0, D1, D2, D3, A0, A1, A2 CE, UPDATE 2.0 V min 0.8 V max VOH VOL IIH IIL IOH IOL DATA OUT DATA OUT RESET, SER/PAR CLK, D0, D1, D2, D3, A0, A1, A2 CE, UPDATE RESET, SER/PAR CLK, D0, D1, D2, D3, A0, A1, A2 CE, UPDATE DATA OUT DATA OUT 2.7 V min 0.5 V max 20 µA max –400 µA min –400 µA max 3.0 mA min –4– REV. 0 AD8108/AD8109 ABSOLUTE MAXIMUM RATINGS 1 MAXIMUM POWER DISSIPATION Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12.0 V Internal Power Dissipation2 AD8108/AD8109 80-Lead Plastic TQFP (ST) . . . . . 2.6 W Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .± VS Output Short Circuit Duration . . . . . . . . . . . . . . . . . . . . . . Observe Power Derating Curves Storage Temperature Range . . . . . . . . . . . . –65°C to +125°C Lead Temperature Range (Soldering 10 sec) . . . . . . . . +300°C The maximum power that can be safely dissipated by the AD8108/AD8109 is limited by the associated rise in junction temperature. The maximum safe junction temperature for plastic encapsulated devices is determined by the glass transition temperature of the plastic, approximately +150°C. Temporarily exceeding this limit may cause a shift in parametric performance due to a change in the stresses exerted on the die by the package. Exceeding a junction temperature of +175°C for an extended period can result in device failure. NOTES 1 Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2 Specification is for device in free air (T A = +25°C): 80-lead plastic TQFP (ST): θ JA = 48°C/W. While the AD8108/AD8109 is internally short circuit protected, this may not be sufficient to guarantee that the maximum junction temperature (+150°C) is not exceeded under all conditions. To ensure proper operation, it is necessary to observe the maximum power derating curves shown in Figure 3. MAXIMUM POWER DISSIPATION – Watts 5.0 TJ = 1508C 4.0 3.0 2.0 1.0 0 –50 –40 –30 –20 –10 0 10 20 30 40 50 60 70 AMBIENT TEMPERATURE – 8C 80 90 Figure 3. Maximum Power Dissipation vs. Temperature ORDERING GUIDE Model AD8108AST AD8109AST AD8108-EB AD8109-EB Temperature Range Package Description Package Option –40°C to +85°C –40°C to +85°C 80-Lead Plastic TQFP (12 mm × 12 mm) 80-Lead Plastic TQFP (12 mm × 12 mm) Evaluation Board Evaluation Board ST-80A ST-80A CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD8108/AD8109 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. REV. 0 –5– WARNING! ESD SENSITIVE DEVICE AD8108/AD8109 Table III. Operation Truth Table CE UPDATE CLK DATA IN DATA OUT RESET SER/ PAR 1 0 X 1 X f X Data i X Data i-32 X 1 X 0 0 1 f D0 . . . D3, A0 . . . A2 NA in Parallel Mode 1 1 0 0 X X X 1 X X X X X X 0 X Operation/Comment No change in logic. The data on the serial DATA IN line is loaded into serial register. The first bit clocked into the serial register appears at DATA OUT 32 clocks later. The data on the parallel data lines, D0–D3, are loaded into the 32-bit serial shift register location addressed by A0–A2. Data in the 32-bit shift register transfers into the parallel latches that control the switch array. Latches are transparent. Asynchronous operation. All outputs are disabled. Remainder of logic is unchanged. D0 D1 D2 (OUTPUT ENABLE) D3 PARALLEL DATA SER/PAR DATA IN (SERIAL) S D1 Q D Q S D1 Q D Q S D1 Q D Q S D1 Q D Q S D1 Q D Q S D1 D0 CLK D0 CLK D0 CLK D0 CLK D0 CLK S D1 Q D Q D0 CLK Q D0 D Q S D1 Q D Q S D1 Q D Q S D1 Q D Q CLK D0 CLK D0 CLK D0 CLK DATA OUT CLK CE UPDATE OUT0 EN A0 A1 A2 3 TO 8 DECODER OUT1 EN OUT2 EN OUT3 EN OUT4 EN OUT5 EN OUT6 EN OUT7 EN LE D LE D LE D LE D LE D LE D LE D LE D LE D LE D OUT0 B0 OUT0 B1 OUT0 B2 OUT0 EN OUT1 B0 OUT6 EN OUT7 B0 OUT7 B1 OUT7 B2 OUT7 EN Q Q Q Q CLR Q Q Q Q CLR Q CLR Q RESET (OUTPUT ENABLE) DECODE 64 SWITCH MATRIX 8 OUTPUT ENABLE Figure 4. Logic Diagram –6– REV. 0 AD8108/AD8109 PIN FUNCTION DESCRIPTIONS Pin Name Pin Numbers Pin Description INxx DATA IN CLK DATA OUT UPDATE 1, 3, 5, 7, 9, 11, 13, 15 57 58 59 56 RESET CE SER/PAR OUTyy AGND DVCC DGND AVEE AVCC AGNDxx AVCCxx/yy AVEExx/yy A0 A1 A2 D0 D1 D2 D3 NC 61 60 55 41, 38, 35, 32, 29, 26, 23, 20 2, 4, 6, 8, 10, 12, 14, 16, 46 63, 79 62, 80 17, 45 18, 44 42, 39, 36, 33, 30, 27, 24, 21 43, 37, 31, 25, 22, 19 40, 34, 28, 22 54 53 52 51 50 49 48 47, 64–78 Analog Inputs; xx = Channel Numbers 00 Through 07. Serial Data Input, TTL Compatible. Clock, TTL Compatible. Falling Edge Triggered. Serial Data Out, TTL Compatible. Enable (Transparent) “Low.” Allows serial register to connect directly to switch matrix. Data latched when “High.” Disable Outputs, Active “Low.” Chip Enable, Enable “Low.” Must be “low” to clock in and latch data. Selects Serial Data Mode, “Low” or Parallel Data Mode, “High.” Must be connected. Analog Outputs yy = Channel Numbers 00 Through 07. Analog Ground for Inputs and Switch Matrix. +5 V for Digital Circuitry. Ground for Digital Circuitry. –5 V for Inputs and Switch Matrix. +5 V for Inputs and Switch Matrix Ground for Output Amp, xx = Output Channel Numbers 00 Through 07. Must be connected. +5 V for Output Amplifier that is shared by Channel Numbers xx and yy. Must be connected. –5 V for Output Amplifier that is shared by Channel Numbers xx and yy. Must be connected. Parallel Data Input, TTL Compatible (Output Select LSB). Parallel Data Input, TTL Compatible (Output Select). Parallel Data Input, TTL Compatible (Output Select MSB). Parallel Data Input, TTL Compatible (Input Select LSB). Parallel Data Input, TTL Compatible (Input Select). Parallel Data Input, TTL Compatible (Input Select MSB). Parallel Data Input, TTL Compatible (Output Enable). Not Connected. VCC VCC VCC ESD ESD ESD RESET OUTPUT INPUT ESD ESD 1kV (AD8109 ONLY) ESD AVEE AVEE a. Analog Input DGND b. Analog Output c. Reset Input VCC VCC 2kV ESD ESD OUTPUT INPUT ESD ESD DGND DGND d. Logic Input e. Logic Output Figure 5. I/O Schematics REV. 0 20kV –7– AD8108/AD8109 1 2 61 RESET 62 DGND 63 DVCC 64 NC 66 NC 65 NC 67 NC 68 NC 69 NC 70 NC 71 NC 72 NC 73 NC 74 NC 75 NC 77 NC 76 NC 78 NC 80 DGND IN00 AGND 79 DVCC PIN CONFIGURATION 60 CE PIN 1 IDENTIFIER 59 DATA OUT IN01 3 58 CLK AGND 4 57 DATA IN IN02 5 AGND 6 56 UPDATE 55 SER/PAR 54 A0 IN03 7 AGND 8 IN04 9 53 A1 AGND 10 AD8108/AD8109 52 A2 TOP VIEW (Not to Scale) 50 D1 IN05 11 51 D0 49 D2 AGND 12 IN06 13 48 D3 AGND 14 47 NC IN07 15 AGND 16 46 AGND AVEE 17 AVCC 18 44 AVCC 45 AVEE 43 AVCC00 42 AGND00 AVCC07 19 OUT07 20 AVEE00/01 40 AGND01 39 OUT01 38 AVCC01/02 37 AGND02 36 OUT02 35 AVEE02/03 34 AGND03 33 OUT03 32 AVCC03/04 31 AGND04 30 OUT04 29 AVEE04/05 28 OUT05 26 AGND05 27 AVCC05/06 25 OUT06 23 AGND06 24 AGND07 21 AVEE06/07 22 41 OUT00 NC = NO CONNECT –8– REV. 0 AD8108/AD8109 5 0.4 RL = 150V 0.3 0.2 2 0.1 FLATNESS 0 1 200mV p-p 0 –0.1 GAIN +50mV 25mV/DIV 3 FLATNESS – dB GAIN – dB 4 +25mV 0 –25mV –50mV –0.2 –1 2V p-p –0.3 –2 –3 100k 1M 10M FREQUENCY – Hz –0.4 1G 100M 10ns/DIV Figure 9. AD8108 Step Response, 100 mV Step Figure 6. AD8108 Frequency Response –10 RL = 1kV –20 –40 +1.0V –50 500mV/DIV CROSSTALK – dB –30 ALL HOSTILE –60 –70 +0.5V 0 –0.5V –1.0V –80 ADJACENT –90 –100 –110 0.2 10ns/DIV 1 10 FREQUENCY – MHz 100 200 Figure 7. AD8108 Crosstalk vs. Frequency Figure 10. AD8108 Step Response, 2 V Step –30 –40 RL = 150V VOUT = 2V p-p 2V STEP RL = 150V 0.2 2ND HARMONIC 0.1%/DIV DISTORTION – dB –50 –60 –70 0.1 0 –0.1 –0.2 –80 3RD HARMONIC –90 –100 100k 0 1M 10M FREQUENCY – Hz 100M Figure 8. AD8108 Distortion vs. Frequency REV. 0 10 20 30 40 50 10ns/DIV 60 70 80 Figure 11. AD8108 Settling Time –9– AD8108/AD8109 5 0.4 4 0.3 3 0.2 FLATNESS 200mV p-p 1 0 –0.1 0 GAIN +50mV 25mV/DIV 0.1 2 FLATNESS – dB GAIN – dB 2V p-p –3 100k 1M 10M FREQUENCY – Hz –25mV –0.3 2V p-p –2 0 –50mV –0.2 –1 +25mV –0.4 1G 100M 10ns/DIV Figure 12. AD8109 Frequency Response Figure 15. AD8109 Step Response, 100 mV Step –20 RL = 1kV –30 –50 +1.0V –60 +0.5V 0.5V/DIV CROSSTALK – dB –40 ADJACENT –70 0 –0.5V –80 –1.0V ALL HOSTILE –90 –100 –110 300k 10ns/DIV 1M 10M FREQUENCY – Hz 100M 200M Figure 16. AD8109 Step Response, 2 V Step Figure 13. AD8109 Crosstalk vs. Frequency –30 –40 RL = 150V VOUT = 2V p-p 2V STEP RTO RL = 150V 0.2 2ND HARMONIC –60 0.1%/DIV DISTORTION – dB –50 –70 –80 0.1 0 –0.1 –0.2 3RD HARMONIC –90 –100 100k 0 1M 10M FREQUENCY – Hz 100M Figure 14. AD8109 Distortion vs. Frequency 20 40 10ns/DIV 60 80 Figure 17. AD8109 Settling Time –10– REV. 0 AD8108/AD8109 –30 5 1V/DIV –50 3 UPDATE INPUT 2 –60 1 0 –70 –80 –90 10k 100k 1M FREQUENCY – Hz 10 TYPICAL VIDEO OUT (RTO) 0 –10 50ns/DIV 10M Figure 18. AD8108 PSRR vs. Frequency Figure 21. AD8108 Switching Transient (Glitch) –40 100 –50 56.3 VIN = 2V p-p RL = 150V OFF ISOLATION – dB –60 31.6 nV/ Hz SWITCHING BETWEEN TWO INPUTS 4 10mV/DIV POWER SUPPLY REJECTION – dB RL = 150V –40 17.8 10 –70 –80 –90 –100 –110 –120 5.63 –130 3.16 10 100 1k 10k 100k FREQUENCY – Hz 1M –140 100k 10M 1k 100k 100 OUTPUT IMPEDANCE – V OUTPUT IMPEDANCE – V 1M 10k 1k 10 FREQUENCY – MHz 100 500 Figure 20. AD8108 Output Impedance, Disabled REV. 0 100M 500M 10 1 0.1 100k 100 1 10M FREQUENCY – Hz Figure 22. AD8108 Off Isolation, Input-Output Figure 19. AD8108 Voltage Noise vs. Frequency 0.1 1M 1M 10M FREQUENCY – Hz 100M 500M Figure 23. AD8108 Output Impedance, Enabled –11– AD8108/AD8109 –30 4 1V/DIV –50 –60 3 UPDATE INPUT 2 1 0 –70 –80 –90 10k 100k 1M FREQUENCY – Hz 10 TYPICAL VIDEO OUT (RTO) 0 –10 50ns/DIV 10M Figure 24. AD8109 PSRR vs. Frequency Figure 27. AD8109 Switching Transient (Glitch) –40 100 –50 56.3 VOUT = 2V p-p RL = 150V –60 –70 OFF ISOLATION – dB 31.6 nV/ Hz SWITCHING BETWEEN TWO INPUTS 5 10mV/DIV POWER SUPPLY REJECTION – dB RTI RL = 150V –40 17.8 10 –80 –90 –100 –110 –120 5.63 –130 3.16 10 100 1k 10k 100k FREQUENCY – Hz 1M –140 100k 10M 1k 10k 100 OUTPUT IMPEDANCE – V OUTPUT IMPEDANCE – V 100k 1k 100 1M 10M FREQUENCY – Hz 100M 10M FREQUENCY – Hz 100M 500M Figure 28. AD8109 Off Isolation, Input-Output Figure 25. AD8109 Voltage Noise vs. Frequency 1 100k 1M 10 1 0.1 100k 500M 1M 10M FREQUENCY – Hz 100M 500M Figure 29. AD8109 Output Impedance, Enabled Figure 26. AD8109 Output Impedance, Disabled –12– REV. 0 AD8108/AD8109 1V/DIV 100k VOUT 1 INPUT 1 AT +1V 0 –1 INPUT 0 AT –1V 10k 5 2V/DIV INPUT IMPEDANCE – V 1M 1k UPDATE 0 100 30k 100k 1M 10M FREQUENCY – Hz 100M 50ns/DIV 500M Figure 30. AD8108 Input Impedance vs. Frequency 8 Figure 33. AD8108 Switching Time 900 VIN = 200mV RL = 150V CL = 18pF 6 800 700 FREQUENCY 4 GAIN – dB 2 CL = 12pF 0 –2 500 400 –4 300 –6 200 –8 100 30k 100k 1M 10M 100M FREQUENCY – Hz 1G 0 –0.020 3G Figure 31. AD8108 Frequency Response vs. Capacitive Load 0.4 –0.010 0.000 0.010 OFFSET VOLTAGE – Volts 0.020 Figure 34. AD8108 Offset Voltage Distribution 0.5 2.0 VIN = 200mV RL = 150V 1.5 CL = 18pF 0.3 1.0 0.2 0.5 0.1 VOS – mV FLATNESS – dB 600 0 CL = 12pF –0.1 0.0 –0.5 –0.2 –1.0 –0.3 –1.5 –0.4 –0.5 30k 100k 1M 10M 100M FREQUENCY – Hz 1G –2.0 –60 3G Figure 32. AD8108 Flatness vs. Capacitive Load REV. 0 –40 –20 0 20 40 TEMPERATURE – 8C 60 80 100 Figure 35. AD8108 Offset Voltage Drift vs. Temperature (Normalized at +25 °C) –13– AD8108/AD8109 1M 1V/DIV 1 INPUT 1 AT +1V 0 –1 10k INPUT 0 AT –1V 5 2V/DIV INPUT IMPEDANCE – V VOUT 100k 1k UPDATE 0 100 30k 100k 1M 10M FREQUENCY – Hz 100M 50ns/DIV 500M Figure 36. AD8109 Input Impedance vs. Frequency Figure 39. AD8109 Switching Time 320 8 VIN = 100mV RL = 150V 300 280 6 260 CL = 18pF 240 FREQUENCY GAIN – dB 4 2 0 –2 CL = 12pF 220 200 180 160 140 120 –4 100 –6 80 –8 60 30k 100k 1M 10M 100M FREQUENCY – Hz 1G 40 0 –0.020 3G Figure 37. AD8109 Frequency Response vs. Capacitive Load –0.010 0.000 0.010 OFFSET VOLTAGE – Volts 0.020 Figure 40. AD8109 Offset Voltage Distribution (RTI) 2.0 0.4 VIN = 100mV RL = 150V 1.5 0.3 CL = 18pF 1.0 0.5 0.1 VOS – mV GAIN – dB 0.2 0 CL = 12pF –0.1 0.0 –0.5 –0.2 –1.0 –0.3 –1.5 –0.4 30k 100k 1M 10M 100M FREQUENCY – Hz 1G –2.0 –60 3G Figure 38. AD8109 Flatness vs. Capacitive Load –40 –20 0 20 40 TEMPERATURE – 8C 60 80 100 Figure 41. AD8109 Offset Voltage Drift vs. Temperature (Normalized at +25 °C) –14– REV. 0 AD8108/AD8109 THEORY OF OPERATION: The AD8108 (G = +1) and AD8109 (G = +2) share a common core architecture consisting of an array of 64 transconductance (gm) input stages organized as eight 8:1 multiplexers with a common, 8-line analog input bus. Each multiplexer is basically a folded-cascode high impedance voltage feedback amplifier with eight input stages. The input stages are NPN differential pairs whose differential current outputs are combined at the output stage, which contains the high impedance node, compensation and a complementary emitter follower output buffer. In the AD8108, the output of each multiplexer is fed back directly to the inverting inputs of its eight gm stages. In the AD8109, the feedback network is a voltage divider consisting of a two equal resistors. The output disable feature of these crosspoints allows larger switch matrices to be built by simply busing together the outputs of multiple 8 × 8 ICs. However, while the disabled output impedance of the AD8108 is very high (10 MΩ), that of the AD8109 is limited by the resistive feedback network (which has a nominal total resistance of 1 kΩ that appears in parallel with the disabled output. If the outputs of multiple AD8109s are connected through separate back termination resistors, the loading due to these finite output impedances will lower the effective back termination impedance of the overall matrix. This problem is eliminated if the outputs of multiple AD8109s are connected directly and share a single back termination resistor for each output of the overall matrix. This configuration increases the capacitive loading of the disabled AD8109s on the output of the enabled AD8109. The AD8108/AD8109 have two options for changing the programming of the crosspoint matrix. In the first, a serial word of 32 bits can be provided that will update the entire matrix each time. The second option allows for changing a single output’s programming via a parallel interface. The serial option requires fewer signals, but requires more time (clock cycles) for changing the programming, while the parallel programming technique requires more signals, but can change a single output at a time and requires fewer clock cycles to complete programming. Serial Programming The serial programming mode uses the device pins CE, CLK, DATA IN, UPDATE, and SER/PAR. The first step is to assert a LOW on SER/PAR in order to enable the serial programming mode. CE for the chip must be LOW to allow data to be clocked into the device. The CE signal can be used to address an individual device when devices are connected in parallel. REV. 0 The data at DATA IN is clocked in at every down edge of CLK. A total of 32 data bits must be shifted in to complete the programming. For each of the eight outputs, there are three bits (D0–D2) that determine the source of its input followed by one bit (D3) that determines the enabled state of the output. If D3 is LOW (output disabled), the three associated bits (D0–D2) do not matter because no input will be switched to that output. The most-significant-output-address data is shifted in first, then following in sequence until the least-significant-output-address data is shifted in. At this point UPDATE can be taken LOW, which will cause the programming of the device according to the data that was just shifted in. The UPDATE registers are asynchronous and when UPDATE is LOW, they are transparent. This switched-gm architecture results in a low power crosspoint switch that is able to directly drive a back terminated video load (150 Ω) with low distortion (differential gain and differential phase errors are better than 0.02% and 0.02°, respectively). This design also achieves high input resistance and low input capacitance without the signal degradation and power dissipation of additional input buffers. However, the small input bias current at any input will increase almost linearly with the number of outputs programmed to that input. APPLICATIONS The UPDATE signal should be HIGH during the time that data is shifted into the device’s serial port. Although the data will still shift in when UPDATE is LOW, the transparent, asynchronous latches will allow the shifting data to reach the matrix. This will cause the matrix to try to update to every intermediate state as defined by the shifting data. If more than one AD8108/AD8109 device is to be serially programmed in a system, the DATA OUT signal from one device can be connected to the DATA IN of the next device to form a serial chain. All of the CLK, CE, UPDATE and SER/PAR pins should be connected in parallel and operated as described above. The serial data is input to the DATA IN pin of the first device of the chain, and it will ripple on through to the last. Therefore, the data for the last device in the chain should come at the beginning of the programming sequence. The length of the programming sequence will be 32 times the number of devices in the chain. PARALLEL PROGRAMMING When using the parallel programming mode, it is not necessary to reprogram the entire device when making changes to the matrix. In fact, parallel programming allows the modification of a single output at a time. Since this takes only one CLK/ UPDATE cycle, significant time savings can be realized by using parallel programming. One important consideration in using parallel programming is that the RESET signal DOES NOT RESET ALL REGISTERS in the AD8108/AD8109. When taken low, the RESET signal will only set each output to the disabled state. This is helpful during power-up to ensure that two parallel outputs will not be active at the same time. After initial power-up, the internal registers in the device will generally have random data, even though the RESET signal was asserted. If parallel programming is used to program one output, that output will be properly programmed but the rest of the device will have a random program state depending on the internal register content at power-up. Therefore, when using parallel programming, it is essential that ALL OUTPUTS BE PROGRAMMED TO A DESIRED STATE AFTER POWER-UP. This will ensure that the programming matrix is always in a known state. From then on, parallel programming can be used to modify a single, or more, output at a time. –15– AD8108/AD8109 In a similar fashion, if both CE and UPDATE are taken LOW after initial power-up, the random power-up data in the shift register will be programmed into the matrix. Therefore, in order to prevent the crosspoint from being programmed into an unknown state DO NOT APPLY LOW LOGIC LEVELS TO BOTH CE AND UPDATE AFTER POWER IS INITIALLY APPLIED. Programming the full shift register one time to a desired state by either serial or parallel programming after initial power-up will eliminate the possibility of programming the matrix to an unknown state. To change an output’s programming via parallel programming, SER/PAR and UPDATE should be taken HIGH and CE should be taken LOW. The CLK signal should be in the HIGH state. The address of the output that is to be programmed should be put on A0–A2. The first three data bits (D0–D2) should contain the information that identifies the input that is programmed to the output that is addressed. The fourth data bit (D3) will determine the enabled state of the output. If D3 is LOW (output disabled) the data on D0–D2 does not matter. After the desired address and data signals have been established, they can be latched into the shift register by a HIGH to LOW transition of the CLK signal. The matrix will not be programmed, however, until the UPDATE signal is taken low. Thus, it is possible to latch in new data for several or all of the outputs first via successive negative transitions of CLK while UPDATE is held high, and then have all the new data take effect when UPDATE goes LOW. This is the technique that should be used when programming the device for the first time after power-up when using parallel programming. POWER-ON RESET When powering up the AD8108/AD8109 it is usually desirable to have the outputs come up in the disabled state. The RESET pin, when taken LOW will cause all outputs to be in the disabled state. However, the RESET signal DOES NOT RESET ALL REGISTERS in the AD8108/AD8109. This is important when operating in the parallel programming mode. Please refer to that section for information about programming internal registers after power-up. Serial programming will program the entire matrix each time, so no special considerations apply. Gain Selection The 8 × 8 crosspoints come in two versions depending on the desired gain of the analog circuit paths. The AD8108 device is unity gain and can be used for analog logic switching and other applications where unity gain is desired. The AD8108 can also be used for the input and interior sections of larger crosspoint arrays where termination of output signals is not usually used. The AD8108 outputs have a very high impedance when their outputs are disabled. For devices that will be used to drive a terminated cable with its outputs, the AD8109 can be used. This device has a built-in gain of two that eliminates the need for a gain-of-two buffer to drive a video line. Because of the presence of the feedback network in these devices, the disabled output impedance is about 1 kΩ. If external amplifiers will be used to provide a G = +2, our AD8079 is a fixed gain of +2 buffer. Creating Larger Crosspoint Arrays The AD8108/AD8109 are high density building blocks for creating crosspoint arrays of dimensions larger than 8 × 8. Various features such as output disable, chip enable, and gain-of-one and -two options are useful for creating larger arrays. For very large arrays, they can be used along with the AD8116, a 16 × 16 video crosspoint device. In addition, systems that require more inputs than outputs can use the AD8110 and/or the AD8111, which are (gain-of-one and gain-of-two) 16 × 8 crosspoint switches. The first consideration in constructing a larger crosspoint is to determine the minimum number of devices required. The 8 × 8 architecture of the AD8108/AD8109 contains 64 “points,” which is a factor of 16 greater than a 4 × 1 crosspoint. The PC board area and power consumption savings are readily apparent when compared to using these smaller devices. For a nonblocking crosspoint, the number of points required is the product of the number of inputs multiplied by the number of outputs. Nonblocking requires that the programming of a given input to one or more outputs does not restrict the availability of that input to be a source for any other outputs. Since the data in the shift register is random after power-up, they should not be used to program the matrix or else the matrix can enter unknown states. To prevent this, DO NOT APPLY LOGIC LOW SIGNALS TO BOTH CE AND UPDATE INITIALLY AFTER POWER-UP. The shift register should first be loaded with the desired data, and then UPDATE can be taken LOW to program the device. The RESET pin has a 20 kΩ pull-up resistor to DVDD that can be used to create a simple power-up reset circuit. A capacitor from RESET to ground will hold RESET LOW for some time while the rest of the device stabilizes. The LOW condition will cause all the outputs to be disabled. The capacitor will then charge through the pull-up resistor to the HIGH state, thus allowing full programming capability of the device. Some nonblocking crosspoint architectures will require more than this minimum as calculated above. Also, there are blocking architectures that can be constructed with fewer devices than this minimum. These systems have connectivity available on a statistical basis that is determined when designing the overall system. The basic concept in constructing larger crosspoint arrays is to connect inputs in parallel in a horizontal direction and to “wireOR” the outputs together in the vertical direction. The meaning of horizontal and vertical can best be understood by looking at a diagram. An 8 input by 16 output crosspoint array can be constructed as shown in Figure 42. This configuration parallels two inputs per channel and does not require paralleling of any outputs. Inputs are easier to parallel than outputs, because there are lower parasitics involved. For a 16 × 8 crosspoint, the AD8110 (gain of one) or AD8111 (gain of two) device can be used. These devices are already configured into a 16 × 8 crosspoint in a single device. –16– REV. 0 AD8108/AD8109 8 8 INPUTS IN 00–07 8 AD8108 OR AD8109 8 AD8108 OR AD8109 ONE TERMINATION PER INPUT At some point, the number of outputs that are wire-ORed becomes too great to maintain system performance. This will vary according to which system specifications are most important. For example, a 64 × 8 crosspoint can be created with eight AD8108/AD8109s. This design will have 64 separate inputs and have the corresponding outputs of each device wire-ORed together in groups of eight. 8 8 16 OUTPUTS OUT 00–15 Figure 42. 8 × 16 Crosspoint Array Using Two AD8108s (Unity Gain) or Two AD8109s (Gain-of-Two) Figure 43 illustrates a 16 × 16 crosspoint array, while a 24 × 24 crosspoint is illustrated in Figure 44. The 16 × 16 crosspoint requires that each input driver drive two inputs in parallel and each output be wire-ORed with one other output. The 24 × 24 crosspoint requires driving three inputs in parallel and having the outputs wire-ORed in groups of three. It is required of the system programming that only one output of a wired-OR node be active at a time. Using additional crosspoint devices in the design can lower the number of outputs that have to be wire-ORed together. Figure 45 shows a block diagram of a system using eight AD8108s and two AD8109s to create a nonblocking, gain-of-two, 64 × 8 crosspoint that restricts the wire-ORing at the output to only four outputs. The rank 1 wire-ORed devices are the AD8108, which has a higher disabled output impedance than the AD8109. RANK 1 (64:16) IN 00–07 IN 08–15 IN 16–23 8 8 8 4 AD8108 4 4 RANK 2 16:8 NONBLOCKING 16:16 BLOCKING AD8108 4 4 AD8108 4 4 4 1kV 8 00–07 838 IN 00–07 IN 24–31 838 8 4 AD8109 4 4 1kV AD8108 4 8 RTERM 8 8 IN 32–39 8 4 4 AD8108 4 AD8109 4 4 IN 40–47 8 IN 08–15 08–15 838 8 RTERM IN 48–55 8 OUT 00–07 OUT 08–15 IN 56–63 Figure 43. 16 × 16 Crosspoint Array Using Four AD8108s or AD8109s IN 00–07 8 838 838 838 8 8 IN 08–15 8 838 8 RTERM 838 8 838 8 8 8 4 1kV 4 ADDITIONAL 8 OUTPUTS (SUBJECT TO BLOCKING) 1kV AD8108 4 838 8 8 8 OUT 00–07 NONBLOCKING RTERM 8 8 4 AD8108 4 4 AD8108 4 Figure 45. Nonblocking 64 × 8 Array with Gain-of-Two (64 × 16 Blocking) Additionally, by using the lower four outputs from each of the two Rank 2 AD8109s, a blocking 64 × 16 crosspoint array can be realized. There are, however, some drawbacks to this technique. The offset voltages of the various cascaded devices will accumulate and the bandwidth limitations of the devices will compound. In addition, the extra devices will consume more current and take up more board space. Once again, the overall system design specifications will determine how to make the various tradeoffs. Multichannel Video 8 IN 16–23 838 838 838 8 8 OUT 00–07 8 RTERM OUT 08–15 8 OUT 16–23 Figure 44. 24 × 24 Crosspoint Array Using Nine AD8108s or AD8109s REV. 0 The excellent video specifications of the AD8108/AD8109 make them ideal candidates for creating composite video crosspoint switches. These can be made quite dense by taking advantage of the AD8108/AD8109’s high level of integration and the fact that composite video requires only one crosspoint channel per system video channel. There are, however, other video formats that can be routed with the AD8108/AD8109 requiring more than one crosspoint channel per video channel. –17– AD8108/AD8109 Some systems use twisted-pair wiring to carry video signals. These systems utilize differential signals and can lower costs because they use lower cost cables, connectors and termination methods. They also have the ability to lower crosstalk and reject common-mode signals, which can be important for equipment that operates in noisy environments or where common-mode voltages are present between transmitting and receiving equipment. When there are many signals in close proximity in a system, as will undoubtedly be the case in a system that uses the AD8108/ AD8109, the crosstalk issues can be quite complex. A good understanding of the nature of crosstalk and some definition of terms is required in order to specify a system that uses one or more AD8108/AD8109s. In such systems, the video signals are differential; there is a positive and negative (or inverted) version of the signals. These complementary signals are transmitted onto each of the two wires of the twisted pair, yielding a first order zero commonmode signal. At the receive end, the signals are differentially received and converted back into a single-ended signal. TYPES OF CROSSTALK Crosstalk can be propagated by means of any of three methods. These fall into the categories of electric field, magnetic field and sharing of common impedances. This section will explain these effects. Every conductor can be both a radiator of electric fields and a receiver of electric fields. The electric field crosstalk mechanism occurs when the electric field created by the transmitter propagates across a stray capacitance (e.g., free space) and couples with the receiver and induces a voltage. This voltage is an unwanted crosstalk signal in any channel that receives it. When switching these differential signals, two channels are required in the switching element to handle the two differential signals that make up the video channel. Thus, one differential video channel is assigned to a pair of crosspoint channels, both input and output. For a single AD8108/AD8109, four differential video channels can be assigned to the eight inputs and eight outputs. This will effectively form a 4 × 4 differential crosspoint switch. Currents flowing in conductors create magnetic fields that circulate around the currents. These magnetic fields will then generate voltages in any other conductors whose paths they link. The undesired induced voltages in these other channels are crosstalk signals. The channels that crosstalk can be said to have a mutual inductance that couples signals from one channel to another. Programming such a device will require that inputs and outputs be programmed in pairs. This information can be deduced by inspection of the programming format of the AD8108/AD8109 and the requirements of the system. The power supplies, grounds and other signal return paths of a multichannel system are generally shared by the various channels. When a current from one channel flows in one of these paths, a voltage that is developed across the impedance becomes an input crosstalk signal for other channels that share the common impedance. There are other analog video formats requiring more than one analog circuit per video channel. One two-circuit format that is commonly being used in systems such as satellite TV, digital cable boxes and higher quality VCRs, is called S-video or Y/C video. This format carries the brightness (luminance or Y) portion of the video signal on one channel and the color (chrominance, chroma or C) on a second channel. Since S-video also uses two separate circuits for one video channel, creating a crosspoint system requires assigning one video channel to two crosspoint channels as in the case of a differential video system. Aside from the nature of the video format, other aspects of these two systems will be the same. There are yet other video formats using three channels to carry the video information. Video cameras produce RGB (red, green, blue) directly from the image sensors. RGB is also the usual format used by computers internally for graphics. RGB can also be converted to Y, R–Y, B–Y format, sometimes called YUV format. These three-circuit, video standards are referred to as component analog video. The component video standards require three crosspoint channels per video channel to handle the switching function. In a fashion similar to the two-circuit video formats, the inputs and outputs are assigned in groups of three and the appropriate logic programming is performed to route the video signals. All these sources of crosstalk are vector quantities, so the magnitudes cannot simply be added together to obtain the total crosstalk. In fact, there are conditions where driving additional circuits in parallel in a given configuration can actually reduce the crosstalk. Areas of Crosstalk For a practical AD8108/AD8109 circuit, it is required that it be mounted to some sort of circuit board in order to connect it to power supplies and measurement equipment. Great care has been taken to create a characterization board (also available as an evaluation board) that adds minimum crosstalk to the intrinsic device. This, however, raises the issue that a system’s crosstalk is a combination of the intrinsic crosstalk of the devices in addition to the circuit board to which they are mounted. It is important to try to separate these two areas of crosstalk when attempting to minimize its effect. In addition, crosstalk can occur among the inputs to a crosspoint and among the outputs. It can also occur from input to output. Techniques will be discussed for diagnosing which part of a system is contributing to crosstalk. CROSSTALK Measuring Crosstalk Many systems, such as broadcast video, that handle numerous analog signal channels have strict requirements for keeping the various signals from influencing any of the others in the system. Crosstalk is the term used to describe the coupling of the signals of other nearby channels to a given channel. Crosstalk is measured by applying a signal to one or more channels and measuring the relative strength of that signal on a desired selected channel. The measurement is usually expressed as dB down from the magnitude of the test signal. The crosstalk is expressed by: |XT| = 20 log 10 (Asel(s)/Atest(s)) –18– REV. 0 AD8108/AD8109 where s = jω is the Laplace transform variable, Asel(s) is the amplitude of the crosstalk-induced signal in the selected channel and Atest(s) is the amplitude of the test signal. It can be seen that crosstalk is a function of frequency, but not a function of the magnitude of the test signal (to first order). In addition, the crosstalk signal will have a phase relative to the test signal associated with it. A network analyzer is most commonly used to measure crosstalk over a frequency range of interest. It can provide both magnitude and phase information about the crosstalk signal. As a crosspoint system or device grows larger, the number of theoretical crosstalk combinations and permutations can become extremely large. For example, in the case of the 8 × 8 matrix of the AD8108/AD8109, we can examine the number of crosstalk terms that can be considered for a single channel, say IN00 input. IN00 is programmed to connect to one of the AD8108/AD8109 outputs where the measurement can be made. We can first measure the crosstalk terms associated with driving a test signal into each of the other seven inputs one at a time. We can then measure the crosstalk terms associated with driving a parallel test signal into all seven other inputs taken two at a time in all possible combinations; and then three at a time, etc., until, finally, there is only one way to drive a test signal into all seven other inputs. Each of these cases is legitimately different from the others and might yield a unique value depending on the resolution of the measurement system, but it is hardly practical to measure all these terms and then to specify them. In addition, this describes the crosstalk matrix for just one input channel. A similar crosstalk matrix can be proposed for every other input. In addition, if the possible combinations and permutations for connecting inputs to the other (not used for measurement) outputs are taken into consideration, the numbers rather quickly grow to astronomical proportions. If a larger crosspoint array of multiple AD8108/AD8109s is constructed, the numbers grow larger still. Obviously, some subset of all these cases must be selected to be used as a guide for a practical measure of crosstalk. One common method is to measure “all hostile” crosstalk. This term means that the crosstalk to the selected channel is measured, while all other system channels are driven in parallel. In general, this will yield the worst crosstalk number, but this is not always the case due to the vector nature of the crosstalk signal. Other useful crosstalk measurements are those created by one nearest neighbor or by the two nearest neighbors on either side. These crosstalk measurements will generally be higher than those of more distant channels, so they can serve as a worst case measure for any other one-channel or two-channel crosstalk measurements. Input and Output Crosstalk The flexible programming capability of the AD8108/AD8109 can be used to diagnose whether crosstalk is occurring more on the input side or the output side. Some examples are illustrative. A given input channel (IN03 in the middle for this example) can be programmed to drive OUT03. The input to IN03 is just terminated to ground (via 50 Ω or 75 Ω) and no signal is applied. REV. 0 All the other inputs are driven in parallel with the same test signal (practically provided by a distribution amplifier), with all other outputs except OUT03 disabled. Since grounded IN03 is programmed to drive OUT03, there should be no signal present. Any signal that is present can be attributed to the other seven hostile input signals, because no other outputs are driven (they are all disabled). Thus, this method measures the allhostile input contribution to crosstalk into IN03. Of course, the method can be used for other input channels and combinations of hostile inputs. For output crosstalk measurement, a single input channel is driven (IN00 for example) and all outputs other than a given output (IN03 in the middle) are programmed to connect to IN00. OUT03 is programmed to connect to IN07 (far away from IN00), which is terminated to ground. Thus OUT03 should not have a signal present since it is listening to a quiet input. Any signal measured at the OUT03 can be attributed to the output crosstalk of the other seven hostile outputs. Again, this method can be modified to measure other channels and other crosspoint matrix combinations. Effect of Impedances on Crosstalk The input side crosstalk can be influenced by the output impedance of the sources that drive the inputs. The lower the impedance of the drive source, the lower the magnitude of the crosstalk. The dominant crosstalk mechanism on the input side is capacitive coupling. The high impedance inputs do not have significant current flow to create magnetically induced crosstalk. However, significant current can flow through the input termination resistors and the loops that drive them. Thus, the PC board on the input side can contribute to magnetically coupled crosstalk. From a circuit standpoint, the input crosstalk mechanism looks like a capacitor coupling to a resistive load. For low frequencies the magnitude of the crosstalk will be given by: |XT| = 20 log10 [(RS CM) × s] where RS is the source resistance, CM is the mutual capacitance between the test signal circuit and the selected circuit, and s is the Laplace transform variable. From the equation it can be observed that this crosstalk mechanism has a high pass nature; it can also be minimized by reducing the coupling capacitance of the input circuits and lowering the output impedance of the drivers. If the input is driven from a 75 Ω terminated cable, the input crosstalk can be reduced by buffering this signal with a low output impedance buffer. On the output side, the crosstalk can be reduced by driving a lighter load. Although the AD8108/AD8109 is specified with excellent differential gain and phase when driving a standard 150 Ω video load, the crosstalk will be higher than the minimum obtainable due to the high output currents. These currents will induce crosstalk via the mutual inductance of the output pins and bond wires of the AD8108/AD8109. –19– AD8108/AD8109 Each output also has an on-chip compensation capacitor that is individually tied the nearby analog ground pins AGND00 through AGND07. This technique reduces crosstalk by preventing the currents that flow in these paths from sharing a common impedance on the IC and in the package pins. These AGNDxx signals should all be directly connected to the ground plane. From a circuit standpoint, this output crosstalk mechanism looks like a transformer, with a mutual inductance between the windings, that drives a load resistor. For low frequencies, the magnitude of the crosstalk is given by: |XT| = 20 log10 (Mxy × s/R L) where Mxy is the mutual inductance of output x to output y and RL is the load resistance on the measured output. This crosstalk mechanism can be minimized by keeping the mutual inductance low and increasing RL . The mutual inductance can be kept low by increasing the spacing of the conductors and minimizing their parallel length. PCB Layout Extreme care must be exercised to minimize additional crosstalk generated by the system circuit board(s). The areas that must be carefully detailed are grounding, shielding, signal routing and supply bypassing. The packaging of the AD8108/AD8109 is designed to help keep the crosstalk to a minimum. Each input is separated from each other input by an analog ground pin. All of these AGNDs should be directly connected to the ground plane of the circuit board. These ground pins provide shielding, low impedance return paths and physical separation for the inputs. All of these help to reduce crosstalk. Each output is separated from its two neighboring outputs by an analog ground pin in addition to an analog supply pin of one polarity or the other. Each of these analog supply pins provides power to the output stages of only the two nearest outputs. These supply pins and analog grounds provide shielding, physical separation and a low impedance supply for the outputs. Individual bypassing of each of these supply pins, with a 0.01 µF chip capacitor directly to the ground plane, minimizes high frequency output crosstalk via the mechanism of sharing common impedances. The input and output signals will have minimum crosstalk if they are located between ground planes on layers above and below, and separated by ground in between. Vias should be located as close to the IC as possible to carry the inputs and outputs to the inner layer. The only place the input and output signals surface is at the input termination resistors and the output series back termination resistors. These signals should also be separated, to the extent possible, as soon as they emerge from the IC package. Evaluation Board A four-layer evaluation board for the AD8108/AD8109 is available. The exact same board and external components are used for each device. The only difference is the device itself, which offers a selection of a gain of unity or gain of two through the analog channels. This board has been carefully laid out and tested to demonstrate the specified high speed performance of the device. Figure 46 shows the schematic of the evaluation board. Figure 47 shows the component side silk-screen. The layouts of the board’s four layers are given in Figures 48, 49, 50 and 51. The evaluation board package includes the following: • Fully populated board with BNC-type connectors. • Windows™ based software for controlling the board from a PC via the printer port. • Custom cable to connect evaluation board to PC. • Disk containing Gerber files of board layout. All trademarks are property of their respective holders. –20– REV. 0 AD8108/AD8109 DVCC DGND P1-1 P1-2 + NC AVEE AGND AVCC P1-3 P1-4 P1-5 NC P1-7 P1-6 + CR1 CR2 1N4148 DVCC + DVCC 0.01mF 0.01mF 0.1mF 10mF 0.1mF 10mF 0.1mF 10mF INPUT 00 75V AVCC AVCC 0.01mF AVEE 0.01mF 0.01mF 80 79 63 43 44 45 46 DGND DVCC DVCC AVCC AVCC AVEE AGND AGND 1 INPUT 00 2 AGND OUTPUT 00 AVEE AGND INPUT 01 75V 3 INPUT 01 4 AGND OUTPUT 01 AVCC AGND INPUT 02 75V 5 INPUT 02 6 AGND OUTPUT 02 AVEE AGND INPUT 03 75V 7 INPUT 03 8 AGND OUTPUT 03 AD8108 OR AD8109 AVCC AGND INPUT 04 75V OUTPUT 04 9 INPUT 04 10 AGND AVEE AGND OUTPUT 05 INPUT 05 75V 11 INPUT 05 12 AGND AVCC AGND OUTPUT 06 INPUT 06 75V 13 INPUT 06 14 AGND AVEE AGND OUTPUT 07 15 INPUT 07 16 AGND AVEE 39 38 AVEE 0.01mF 75V 37 36 35 AVCC 0.01mF 75V 34 33 32 AVEE 0.01mF 75V 31 30 29 AVCC 0.01mF 75V 28 27 26 AVEE 0.01mF 75V 25 24 23 AVCC 0.01mF 75V 22 21 20 AVEE 0.01mF 75V 19 AVCC 18 AVCC 17 AVEE D3 D2 D1 D0 A2 A1 62 61 60 58 56 55 54 53 52 51 50 49 48 R25 20kV P2-3 DVCC P2-1 Figure 46. Evaluation Board Schematic –21– P3-13 P3-12 P3-11 P3-10 P3-9 P3-8 P3-7 P3-6 P3-5 P3-4 P3-3 P3-2 P3-1 NC = NO CONNECT P3-14 NC P2-6 REV. 0 40 0.01mF A0 SER/PAR DATA IN DGND P2-2 75V 0.01mF P2-5 P2-4 AVCC DATA OUT UPDATE 57 41 0.01mF CLK 59 AVCC CE 75V RESET INPUT 07 42 SERIAL MODE JUMP AD8108/AD8109 Figure 47. Component Side Silkscreen Figure 48. Board Layout (Component Side) –22– REV. 0 AD8108/AD8109 Figure 49. Board Layout (Signal Layer) Figure 50. Board Layout (Power Plane) REV. 0 –23– AD8108/AD8109 Figure 51. Board Layout (Bottom Layer) Optimized for video applications, all signal inputs and outputs are terminated with 75 Ω resistors. Stripline techniques are used to achieve a characteristic impedance on the signal input and output lines also of 75 Ω. Figure 52 shows a cross-section of one of the input or output tracks along with the arrangement of the PCB layers. It should be noted that unused regions of the four layers are filled up with ground planes. As a result, the input and output traces, in addition to having controlled impedances, are well shielded. w = 0.008" (0.2mm) TOP LAYER b = 0.024" (0.6mm) a = 0.008" (0.2mm) t = 0.00135" (0.0343mm) The three power supply pins AVCC, DVCC and AVEE should be connected to good quality, low noise, ± 5 V supplies. Where the same ± 5 V power supplies are used for analog and digital, separate cables should be run for the power supply to the evaluation board’s analog and digital power supply pins. As a general rule, each power supply pin (or group of adjacent power supply pins) should be locally decoupled with a 0.01 µF capacitor. If there is a space constraint, it is more important to decouple analog power supply pins before digital power supply pins. A 0.1 µF capacitor, located reasonably close to the pins, can be used to decouple a number of power supply pins. Finally a 10 µF capacitor should be used to decouple power supplies as they come on to the board. Controlling the Evaluation Board from a PC SIGNAL LAYER h = 0.011325" (0.288mm) POWER LAYER BOTTOM LAYER Figure 52. Cross Section of Input and Output Traces The board has 16 BNC type connectors: eight inputs and eight outputs. The connectors are arranged in two crescents around the device. As can be seen from Figure 49, this results in all eight input signal traces and all eight signal output traces having the same length. This is useful in tests such as All-Hostile Crosstalk where the phase relationship and delay between signals needs to be maintained from input to output. The evaluation board include Windows-based control software and a custom cable that connects the board’s digital interface to the printer port of the PC. The wiring of this cable is shown in Figure 53. The software requires Windows 3.1 or later to operate. To install the software, insert the disk labeled “Disk #1 of 2” in the PC and run the file called SETUP.EXE. Additional installation instructions will be given on-screen. Before beginning installation, it is important to terminate any other Windows applications that are running. –24– REV. 0 AD8108/AD8109 RESET MOLEX 0.100" CENTER CRIMP TERMINAL HOUSING D-SUB 25 PIN (MALE) 14 1 1 CLK CE UPDATE DATA IN 6 DGND MOLEX D-SUB-25 TERMINAL HOUSING 3 2 3 1 4 4 5 5 6 2 6 25 EVALUATION BOARD SIGNAL CE RESET UPDATE 25 The software offers volatile and nonvolatile storage of configurations. For volatile storage, up to two configurations can be stored and recalled using the Memory 1 and Memory 2 Buffers. These function in an identical fashion to the memory on a pocket calculator. For nonvolatile storage of a configuration, the Save Setup and Load Setup functions can be used. This stores the configuration as a data file on disk. 13 DATA IN CLK DGND Overshoot on PC Printer Ports’ Data Lines PC Figure 53. Evaluation Board-PC Connection Cable When you launch the crosspoint control software, you will be asked to select the printer port you are using. Most modern PCs have only one printer port, usually called LPT1. However, some laptop computers use the PRN port. Figure 54 shows the main screen of the control software in its initial reset state (all outputs off). Using the mouse, any input can be connected with one or more outputs by simply clicking on the appropriate radio buttons in the 8 × 8 on-screen array. Each time a button is clicked on, the software automatically sends and latches the required 32-bit data stream to the evaluation board. An output can be turned off by clicking the appropriate button in the Off column. To turn off all outputs, click on RESET. The data lines on some printer ports have excessive overshoot. Overshoot on the pin that is used as the serial clock (Pin 6 on the D-Sub-25 connector) can cause communication problems. This overshoot can be eliminated by connecting a capacitor from the CLK line on the evaluation board to ground. A pad has been provided on the solder-side of the evaluation board to allow this capacitor to be soldered into place. Depending upon the overshoot from the printer port, this capacitor may need to be as large as 0.01 µF. AD8108/AD8109 Figure 54. Evaluation Board Control Panel REV. 0 –25– AD8108/AD8109 OUTLINE DIMENSIONS Dimensions shown in inches and (mm). 80-Lead Plastic TQFP (ST-80A) 0.559 (14.20) 0.543 (13.80) 0.476 (12.10) 0.469 (11.90) 0.063 (1.60) MAX 0.030 (0.75) 0.020 (0.50) 80 1 61 60 0.476 (12.10) 0.469 (11.90) 0.559 (14.20) 0.543 (13.80) SEATING PLANE TOP VIEW (PINS DOWN) 0.003 (0.08) MAX 0.006 (0.15) 0.002 (0.05) 20 41 40 21 0.020 (0.50) BSC 0.011 (0.27) 0.007 (0.17) 0.057 (1.45) 0.053 (1.35) –26– REV. 0 –27– –28– PRINTED IN U.S.A. C3209–8–10/97