AD AD8183ARUZ

a
FEATURES
Fully Buffered Inputs and Outputs
Fast Channel-to-Channel Switching: 15 ns
High Speed
380 MHz Bandwidth (–3 dB) 200 mV p-p
310 MHz Bandwidth (–3 dB) 2 V p-p
1000 V/␮s Slew Rate G = +1, 2 V Step
1150 V/␮s Slew Rate G = +2, 2 V Step
Fast Settling Time of 15 ns to 0.1%
Low Power: 25 mA
Excellent Video Specifications (RL = 150 ⍀)
Gain Flatness of 0.1 dB to 90 MHz
0.01% Differential Gain Error
0.02ⴗ Differential Phase Error
Low All-Hostile Crosstalk –84 dB @ 5 MHz
–54 dB @ 50 MHz
Low Channel-to-Channel Crosstalk –56 dB @ 100 MHz
High “OFF” Isolation of –100 dB @ 10 MHz
Low Cost
Fast High Impedance Output Disable Feature for
Connecting Multiple Devices
APPLICATIONS
Pixel Switching for “Picture-In-Picture”
Switching RGB in LCD and Plasma Displays
RGB Video Switchers and Routers
PRODUCT DESCRIPTION
The AD8183 (G = +1) and AD8185 (G = +2) are high speed
triple 2:1 multiplexers. They offer –3 dB signal bandwidth up to
380 MHz, along with slew rate of 1000 V/µs. With better than
–90 dB of channel-to-channel crosstalk and isolation at 10 MHz,
they are useful in many high-speed applications. The differential
gain and differential phase errors of 0.01% and 0.02° respectively,
along with 0.1 dB flatness to 90 MHz make the AD8183 and
AD8185 ideal for professional video and RGB multiplexing. They
offer 15 ns channel-to-channel switching time, making them
an excellent choice for switching video signals, while consuming
less than 25 mA on ± 5 V supply voltages.
Both devices offer a high speed disable feature that can set the
output into a high impedance state. This allows the building of
larger input arrays while minimizing “OFF” channel output
loading. They operate on voltage supplies of ± 5 V and are offered
in a 24-lead TSSOP package.
380 MHz, 25 mA,
Triple 2:1 Multiplexers
AD8183/AD8185
FUNCTIONAL BLOCK DIAGRAM
AD8183/AD8185
IN0A 1
DGND 2
SELECT
24 VCC
23 OE
22 SEL A/B
IN1A 3
DISABLE
GND 4
IN2A 5
0
VCC 6
21 VCC
20 OUT0
19 VEE
VEE 7
1
18 OUT1
17 VCC
IN2B 8
GND 9
2
16 OUT2
IN1B 10
15 VEE
GND 11
14 DVCC
IN0B 12
13 VCC
Table I. Truth Table
SEL A/B
OE
OUT
0
1
0
1
0
0
1
1
INA
INB
High Z
High Z
VO = 1.4V STEP
1.4V RL = 150V
1.2V
1.0V
0.8V
0.6V
0.4V
0.2V
0.0V
200mV
2ns
Figure 1. AD8185 Pulse Response; RL = 150 Ω
REV. 0
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
World Wide Web Site: http://www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 1999
AD8183/AD8185–SPECIFICATIONS (T = 25ⴗC, V = ⴞ5 V, R = 1 k⍀ unless otherwise noted)
A
Parameter
DYNAMIC PERFORMANCE
–3 dB Bandwidth (Small Signal)
–3 dB Bandwidth (Small Signal)
–3 dB Bandwidth (Large Signal)
–3 dB Bandwidth (Large Si
0.1 dB Bandwidth
Slew Rate
Settling Time to 0.1%
NOISE/DISTORTION PERFORMANCE
Differential Gain
Differential Phase
All-Hostile Crosstalk, RTI
Channel-to-Channel Crosstalk, RTI
OFF Isolation
Voltage Noise, RTI
DC PERFORMANCE
Voltage Gain Error
Input Offset Voltage, RTI
Input Offset Voltage Matching, RTI
Input Offset Drift, RTI
Input Bias Current
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
S
L
Condition
Min
Typ
VOUT = 200 mV p-p
VOUT = 200 mV p-p, R L = 150 Ω
VOUT = 2 V p-p
VOUT = 2 V p-p, RL = 150 Ω
VOUT = 200 mV p-p
VOUT = 200 mV p-p, R L = 150 Ω
2 V Step
2 V Step, RL = 150 Ω
250/300
200/250
250/300
200/250
590/360
380/320
530/350
310/300
90/60
100/160
1000/1150
15
MHz
MHz
MHz
MHz
MHz
MHz
V/µs
ns
NTSC or PAL, 150 Ω
NTSC or PAL, 150 Ω
ƒ = 5 MHz, AD8185: R L = 150 Ω
ƒ = 50 MHz, AD8185: RL = 150 Ω
ƒ = 100 MHz, AD8185: R L = 150 Ω
ƒ = 10 MHz, RL = 150 Ω
ƒ = 10 kHz to 30 MHz
0.01
0.02
–84/–72
–54/–50
–56/–54
–100
28/15
%
Degrees
dB
dB
dB
dB
nV/√Hz
No Load
0.20
5
10
1
15
6/10
TMIN to TMAX
Channel-to-Channel
Short Circuit Current
Output Resistance
Output Capacitance
POWER SUPPLY
Operating Range
Power Supply Rejection Ratio
Power Supply Rejection Ratio
Quiescent Current
SWITCHING CHARACTERISTICS
Switch Time
50% Logic to 50% Output Settling
ENABLE to Channel ON Time
50% Logic to 50% Output Settling
ENABLE to Channel OFF Time
50% Logic to 50% Output Settling
Channel Switching Transient (Glitch)
0.25/0.85
25/40
25/40
10/15
Unit
%
mV
mV
mV
µV/°C
µA
4/1
8/5
1
1.5
± 3.0/± 1.5
MΩ
pF
pF
V
RL = 1 kΩ
RL = 150 Ω
± 2.90
± 2.65
Enabled
Disabled
Disabled
4/1
± 3.25
± 2.95
60
0.3
8/3
4/6.5
V
V
mA
Ω
MΩ
pF
Channel Enabled
Channel Disabled
Input Voltage Range
OUTPUT CHARACTERISTICS
Output Voltage Swing
Max
+PSRR +V S = +4.5 V to +5.5 V, –V S = –5 V
–PSRR –VS = –4.5 V to –5.5 V, +VS = +5 V
All Channels “ON”
All Channels “OFF”
TMIN to TMAX ; All Channels “ON”
± 4.5
58/62
52/60
± 5.5
66/72
56/68
25
3/7
25
30
5/10
V
dB
dB
mA
mA
mA
Channel-to-Channel
IN0 = +1 V, IN1 = –1 V
15
ns
INPUT = 1 V
20
ns
INPUT = 1 V
All Inputs Grounded
45
50/70
ns
mV
DIGITAL INPUTS
Logic “1” Voltage
Logic “0” Voltage
Logic “1” Input Current
Logic “0” Input Current
SEL A/B and OE Inputs
SEL A/B and OE Inputs
SEL A/B and OE = 4 V
SEL A/B and OE = 0.4 V
2.0
OPERATING TEMPERATURE RANGE
Temperature Range
θJA
θJC
Operating (Still Air)
Operating (Still Air)
Operating
–40
0.8
10
0.5
+85
128
42
V
V
nA
µA
°C
°C/W
°C/W
Specifications subject to change without notice.
–2–
REV. 0
AD8183/AD8185
ABSOLUTE MAXIMUM RATINGS 1
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.0 V
DVCC to VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 0.2 V
Internal Power Dissipation2, 3
AD8183/AD8185 24-Lead TSSOP (RU) . . . . . . . . . . . . . 1 W
Input Voltage
IN0A, IN0B, IN1A, IN1B, IN2A, IN2B . . . . . VEE ≤ VIN ≤ V CC
SELECT A/B, OE . . . . . . . . . . . . . . . . . . DGND ≤ VIN ≤ VCC
Output Short Circuit Duration . . . . . . . . . . . . . . . . . . . Indefinite3
Storage Temperature Range . . . . . . . . . . . . . . . –65°C to +150°C
Lead Temperature Range (Soldering 10 sec) . . . . . . . . . . . 300°C
MAXIMUM POWER DISSIPATION – Watts
2.0
NOTES
1
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
2
Specification is for device in free air (T A = 25°C).
3
24-lead plastic TSSOP; θ JA = 128°C/W. Maximum internal power dissipation (P D)
should be derated for ambient temperature (T A) such that PD < (150°C–T A)/θJA.
TJ = 1508C
1.5
1.0
0.5
0
–50 –40 –30 –20 –10 0 10 20 30 40 50 60 70
AMBIENT TEMPERATURE – 8C
80 90
Figure 2. Maximum Power Dissipation vs. Temperature
PIN CONFIGURATION
ORDERING GUIDE
Model
AD8183ARU
AD8185ARU
AD8183-EVAL
AD8185-EVAL
Temperature
Range
–40°C to +85°C
–40°C to +85°C
Package
Description
24-Lead Plastic TSSOP
24-Lead Plastic TSSOP
Evaluation Board
Evaluation Board
Package
Option
RU-24
RU-24
IN0A 1
24
VCC
DGND 2
23
OE
IN1A 3
22
SEL A/B
GND 4
21
VCC
20
OUT0
IN2A 5
AD8183/
AD8185
VCC 6
19 VEE
TOP VIEW
VEE 7 (Not to Scale) 18 OUT1
MAXIMUM POWER DISSIPATION
IN2B 8
17
VCC
The maximum power that can be safely dissipated by the AD8183/
AD8185 is limited by the associated rise in junction temperature.
The maximum safe junction temperature for plastic encapsulated
devices is determined by the glass transition temperature of the
plastic, approximately 150°C. Temporarily exceeding this
limit may cause a shift in parametric performance due to a
change in the stresses exerted on the die by the package. Exceeding
a junction temperature of 175°C for an extended period can
result in device failure.
GND 9
16
OUT2
IN1B 10
15
VEE
GND 11
14
DVCC
IN0B 12
13
VCC
While the AD8183/AD8185 is internally short circuit protected,
this may not be sufficient to guarantee that the maximum junction
temperature (150°C) is not exceeded under all conditions. To
ensure proper operation, it is necessary to observe the maximum
power derating curves shown in Figure 2.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD8183/AD8185 features proprietary ESD protection circuitry, permanent damage
may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
REV. 0
–3–
WARNING!
ESD SENSITIVE DEVICE
AD8183/AD8185
1
1
GAIN
GAIN
0
200mV p-p
–1
–3
0
–4
–0.1
–0.2
–5
200mV p-p
2V p-p
VO AS SHOWN
RL = 150V
–0.3
–7
–0.4
–8
–9
0.1
1
10
FREQUENCY – MHz
100
1k
0
0
–4
–0.1
–0.2
–5
–6
VO AS SHOWN
RL = 150V
–8
–0.5
–0.6
–9
0.1
1
10
FREQUENCY – MHz
2
200mV p-p
0.3
1
GAIN
0.2
–2
0.1
0
–4
–0.1
–0.2
2V p-p
–0.3
FLATNESS – dB
GAIN – dB
FLATNESS
–3
200mV p-p
2V p-p
0.1
–1
FLATNESS
0
–2
–3
–0.1
200mV p-p
2V p-p
–0.2
–4
–5
VO AS SHOWN
RL = 1kV
–0.3
–7
–0.4
–6
–0.4
–8
–0.5
–7
–0.5
–9
0.1
1
10
FREQUENCY – MHz
–0.6
1k
100
–8
0.1
VO = 200mV p-p
RL = 1kV
CL = 5pF
TEMPERATURE AS SHOWN
3
2
NORMALIZED GAIN – dB
3
+25 C
2
+85 C
1
0
–40 C
–1
–2
–0.6
1k
100
–2
–3
–5
100
–6
0.1
1k
–40 C
–1
–4
10
FREQUENCY – MHz
+25 C
+85 C
0
–4
1
VO = 200mV p-p
RL = 150V
CL = 5pF
TEMPERATURE AS SHOWN
1
–3
–5
0.1
10
FREQUENCY – MHz
4
5
4
1
Figure 7. AD8185 Frequency Response; RL = 1 kΩ
Figure 4. AD8183 Frequency Response; RL = 1 k Ω
GAIN – dB
0.2
0
NORMALIZED GAIN – dB
–1
–6
–0.6
1k
100
Figure 6. AD8185 Frequency Response; RL = 150 Ω
2V p-p
VO AS SHOWN
RL = 1kV
–0.3
–0.5
0.3
–5
200mV p-p
2V p-p
–0.4
200mV p-p
GAIN
–3
–7
Figure 3. AD8183 Frequency Response; RL = 150 Ω
1
0.1
FLATNESS
NORMALIZED FLATNESS – dB
2V p-p
2V p-p
–2
NORMALIZED FLATNESS – dB
FLATNESS
FLATNESS – dB
0.1
–2
GAIN – dB
NORMALIZED GAIN – dB
–1
–6
200mV p-p
0
1
10
FREQUENCY – MHz
100
1k
Figure 8. AD8185 Frequency Response vs. Temperature
Figure 5. AD8183 Frequency Response vs. Temperature
–4–
REV. 0
AD8183/AD8185
–10
–10
RL = 1kV
RT = 37.5V
–30
–30
–40
–40
–50
ALL-HOSTILE
–60
ADJACENT
–70
–90
–100
–100
10
100
FREQUENCY – MHz
1
–110
1k
ADJACENT
CHANNEL-TO-CHANNEL CROSSTALK – dB
–40
–50
–60
DRIVE B, LISTEN A
–70
–80
DRIVE A, LISTEN B
–90
–100
10
100
FREQUENCY – MHz
1
RL = 150V
RT = 37.5V
RTI MEASURED
–20
–30
–40
–50
–60
DRIVE A, LISTEN B
–70
–80
DRIVE B, LISTEN A
–90
–100
–110
1k
Figure 10. AD8183 Channel-to-Channel Crosstalk vs.
Frequency
10
100
FREQUENCY – MHz
1
1k
Figure 13. AD8185 Channel-to-Channel Crosstalk vs.
Frequency
0
0
VO = 2V p-p
RL = 150V
–10
VO = 2V p-p
RL = 150V
–10
–20
–30
–30
DISTORTION – dBc
–20
–40
–50
SECOND HARMONIC
–60
–70
–40
–50
SECOND HARMONIC
–60
–70
THIRD HARMONIC
THIRD HARMONIC
–80
–80
–90
–90
1
10
FUNDAMENTAL FREQUENCY – MHz
–100
100
1
10
FUNDAMENTAL FREQUENCY – MHz
100
Figure 14. AD8185 Distortion vs. Frequency
Figure 11. AD8183 Distortion vs. Frequency
REV. 0
1k
–10
–30
–100
10
100
FREQUENCY – MHz
1
Figure 12. AD8185 Crosstalk vs. Frequency
RL = 1kV
RT = 37.5V
–20
–110
ALL-HOSTILE
–70
–80
–10
CHANNEL-TO-CHANNELCROSSTALK – dB
–60
–90
Figure 9. AD8183 Crosstalk vs. Frequency
DISTORTION – dBc
–50
–80
–110
RL = 150V
RT = 37.5V
RTI MEASURED
–20
CROSSTALK – dB
CROSSTALK – dB
–20
–5–
0
1M
1M
1M
INPUT IMPEDANCE – V
INPUT IMPEDANCE – V
AD8183/AD8185
100k
10k
1k
100k
1k
100
100
0.1
10k
1
10
FREQUENCY – MHz
100
0.1
1k
1
10
FREQUENCY – MHz
100
1k
Figure 18. AD8185 Input Impedance vs. Frequency
Figure 15. AD8183 Input Impedance vs. Frequency
1k
1k
100
OUTPUT IMPEDANCE – V
OUTPUT IMPEDANCE – V
1k
10
1
0.1
0.1
10
1
0.1
1
10
FREQUENCY – MHz
100
0.1
1k
1M
100k
100k
OUTPUT IMPEDANCE – V
1M
10k
1k
100
10
0.1
1
10
FREQUENCY – MHz
100
1k
Figure 19. AD8185 Output Impedance vs. Frequency;
Enabled
Figure 16. AD8183 Output Impedance vs. Frequency;
Enabled
OUTPUT IMPEDANCE – V
100
10k
1k
100
1
10
FREQUENCY – MHz
100
10
0.1
1k
Figure 17. AD8183 Output Impedance, vs. Frequency;
Disabled
1
10
FREQUENCY – MHz
100
1k
Figure 20. AD8185 Output Impedance vs. Frequency;
Disabled
–6–
REV. 0
–40
–40
–50
–50
–60
–60
–70
–70
OFF ISOLATION – dB
OFF ISOLATION – dB
AD8183/AD8185
–80
–90
–100
–110
–80
–90
–100
–110
–120
–120
–130
–130
–140
0.1
1
10
FREQUENCY – MHz
100
–140
0.1
500
10
FREQUENCY – MHz
100
500
Figure 24. AD8185 Off Isolation, Input–Output
Figure 21. AD8183 Off Isolation, Input–Output
–10
0
0
10
10
20
20
PSRR – dB
–10
PSRR – dB
1
30
–PSRR
40
–PSRR
30
40
+PSRR
50
50
+PSRR
60
60
70
70
80
0.1
1
10
FREQUENCY – MHz
80
0.1
100
170
150
150
VOLTAGE NOISE – nV/ Hz
VOLTAGE NOISE – nV/ Hz
170
130
110
90
70
50
100
130
110
90
70
50
30
30
10
10
100
1k
10k
100k
FREQUENCY – Hz
1M
10M
10
100
1k
10k
100k
FREQUENCY – Hz
1M
10M
Figure 26. AD8185 RTI Voltage Noise vs. Frequency
Figure 23. AD8183 Voltage Noise vs. Frequency
REV. 0
10
FREQUENCY – MHz
Figure 25. AD8185 PSRR vs. Frequency
Figure 22. AD8183 PSRR vs. Frequency
10
1
–7–
AD8183/AD8185
VO = 2V STEP
RL = 150V
0.1%/DIV
0.1%/DIV
VO = 2V STEP
RL = 150V
0
5
10
15 20 25 30
5ns/DIV
0
35 40
10
15 20 25 30
5ns/DIV
35 40
Figure 30. AD8185 0.1% Settling Time
Figure 27. AD8183 0.1% Settling Time
+1.8V
100
+1.8V
100
5
90
90
SEL A/B
SEL A/B
+1.0V
+1.0V
IN0A AT
+0.5V
IN0A AT +1V
+1.0V
+1.0V
V OUT
V OUT
10
0%
10
0V
IN0B
AT –1V
0%
0V
IN0B AT
–0.5V
–1.0V
–1.0V
10ns
10ns
Figure 31. AD8185 Channel-to-Channel Switching Time
Figure 28. AD8183 Channel-to-Channel Switching Time
100
+1.8V
SEL A/B
100
+1.0V
90
+1.8V
SEL A/B
+1.0V
90
+0.05V
+0.05V
0V
0V
–0.05V
10
–0.05V
10
0%
0%
10ns
10ns
Figure 32. AD8185 Channel-to-Channel Switching
Transient (Glitch)
Figure 29. AD8183 Channel-to-Channel Switching
Transient (Glitch)
–8–
REV. 0
AD8183/AD8185
VO = 200mV STEP
0.1V R = 150V
L
VO = 200mV STEP
0.10V R = 1kV
L
0.05V
0.05V
0.0V
0.0V
–0.05V
–0.05V
–0.10V
–0.1V
25mV
2ns
VO = 0.7V STEP
0.7V R = 1kV
L
VO = 1.4V STEP
1.4V R = 150V
L
0.6V
1.2V
0.5V
1.0V
0.4V
0.8V
0.3V
0.6V
0.2V
0.4V
0.1V
0.2V
0.0V
0.0V
100mV
200mV
2ns
2ns
Figure 37. AD8185 Video Amplitude Pulse Response;
RL = 150 Ω
Figure 34. AD8183 Video Amplitude Pulse Response;
RL = 1 kΩ
VO = 2V STEP
1.0V R = 1kV
L
VO = 2V STEP
1.0V R = 150V
L
0.5V
0.5V
0.0V
0.0V
–0.5V
–0.5V
–1.0V
2ns
Figure 36. AD8185 Small Signal Pulse Response;
RL = 150 Ω
Figure 33. AD8183 Small Signal Pulse Response;
RL = 1 kΩ
–1.0V
250mV
250mV
2ns
2ns
Figure 38. AD8185 Large Signal Pulse Response;
RL = 150 Ω
Figure 35. AD8183 Large Signal Pulse Response;
RL = 1 kΩ
REV. 0
25mV
–9–
AD8183/AD8185
THEORY OF OPERATION
The AD8183 (G = +1) and AD8185 (G = +2) are triple-output,
2:1 multiplexers with TTL-compatible global input switching
and output enable control. Optimized for selecting between two
RGB (red, green, blue) video sources, the devices have high
peak slew rates, maintaining their bandwidth for large signals.
Additionally, the multiplexers are compensated for high phase
margin, minimizing overshoot for good pixel resolution. The
multiplexers also have video specifications that are suitable for
switching NTSC or PAL composite signals.
RS = 0V, CL = 5pF
0.0V
APPLICATIONS
Driving Capacitive Loads
When driving a large capacitive load, most amplifiers will exhibit
peaking/ringing in pulse response. To minimize peaking, and to
ensure stability for larger values of capacitive loads, a small
resistor, RS, can be added between the output and the load
capacitor, CL. This is shown in Figure 39.
RS = 15V, CL = 20pF
250mV
5ns
Figure 39. Pulse Responses Driving Capacitive Loads
Power Supply and Layout Considerations
The AD8183 and AD8185 are very high performance muxes
that require attention to several important design details to realize their specified performance. Good high-frequency layout
rules must be carefully observed.
A good design will start with a solid ground plane. All the GND
pins of the part(s) should be directly connected to it. In addition, bypass capacitors should be connected from each supply
pin (VCC and VEE) to the ground plane. It is suggested to use
0.01 µF surface-mount chip capacitors as close to the IC as
possible to provide high-frequency bypassing.
For lower frequency bypassing, higher value tantalum capacitors—
at least 10 µF—should be provided from both VCC and VEE to
ground. These do not have to be as close to the IC pins, because
parasitic inductance is not as big a factor at low frequencies.
Please refer to AD8183/AD8185 Evaluation Board Operation
Guide for further information.
Crosstalk
Note that full power bandwidth for an undistorted sinusoidal
signal is often calculated using peak slew rate from the equation:
Peak slew rate is not the same as average slew rate (25% to 75%)
as typically specified. For a natural response, peak slew rate
may be 2.7 times larger than average slew rate. Therefore, calculating a full power bandwidth with a specified average slew rate
will give a pessimistic result.
1kV
RS = 20V, CL = 20pF
One logic pin OE controls whether the three outputs are
enabled, or disabled to a high-impedance state. The high
impedance disable allows larger matrices to be built when
busing the outputs together. Also, when not in use the outputs
can be disabled to reduce power consumption. In the case of
the AD8185 (G = +2), a feedback isolation scheme is used so
that the impedance of the gain-of-two feedback network does
not load the output.
(2 × π × Sinusoid Amplitude)
VOUT
CL
–0.5V
The transconductance stages, NPN differential pairs, source
signal current into the folded cascode output stages. Each output stage contains a compensating network and emitter follower
output buffer. Internal voltage feedback sets the gain with the
AD8183 being configured as a unity gain follower, and the
AD8185 as a gain-of-two amplifier with a feedback network.
This architecture provides drive for a reverse-terminated video
load (150 Ω) with low differential gain and phase error for
relatively low power consumption. Careful chip design and
layout allow excellent crosstalk isolation between channels.
Peak Slew Rate
RS
0.5V
The multiplexers are organized as three independent channels,
each with two input transconductance stages and one output
transimpedance stage. The appropriate input transconductance
stages are selected via one logic pin (SELECT A/B), such that
all three outputs switch input connections simultaneously. The
unused input stages are disabled with a “t-switch” scheme to
provide excellent crosstalk isolation between “on” and “off”
inputs. No additional input buffering is necessary, resulting in
low input capacitance and high input impedance without additional signal degradation.
Full Power Bandwidth =
VIN
75V
In normal operation the AD8183 and AD8185 will have signals
at some of the input pins that are not switched to appear at the
output. In addition, several signal paths will in general be active
at one time. In any system that has high-frequency signals that
are brought together in close proximity, there will be inevitable
crosstalk, whereby some fraction of the undesired signals will
appear at the outputs. This can result, for example, in ghost images
in an RGB monitor muxing application.
The AD8183 and AD8185 are capable of excellent lowcrosstalk performance. However, in order to realize the best
possible crosstalk performance, certain design details should be
followed. Most of the low-crosstalk specification is inherent in
the part and will result from observing the power supply and
layout consideration discussed above. This is because each of
the input and output pins are separated by at least either a
supply pin or a ground pin.
This package architecture helps the crosstalk performance in at
least three ways. First, the supply and ground pins provide extra
physical separation between the input- and output-signal pins.
Physical separation is a very effective technique for reducing
crosstalk.
Second, the supply and ground pins are at ac ground, and therefore provide a degree of shielding between the signals. This
works for both capacitive crosstalk, which is due to voltages on
the signals, and inductive crosstalk, which is due to currents that
flow through the signal paths.
–10–
REV. 0
AD8183/AD8185
Third, the additional power and ground pins also yield lower
impedance on the power and ground lines, and therefore minimize
the effects of shared impedances on crosstalk.
A delay circuit is provided for each device to ensure that the
outputs of one device are disabled before the outputs of the
other are enabled.
Signal routing is also important for keeping crosstalk low.
Shielding and separation should be used for signals that must
run parallel over some length on the PC board. If signals must
cross, the trace widths should be kept narrow, and the signals
should cross at right angles to minimize the capacitance between
the traces.
If the RGB signals contain the sync information, such as a syncon-Green, this circuit is all that is necessary for the full 4:1 RGB
mux. However, if sync is carried on separate signals, such as in
PCs, the sync signals can be multiplexed through a digital multiplexer that operates from the same SEL signals.
4:1 RGB Multiplexer
For selecting among four RGB sources to drive a monitor, two
AD8185s can be combined to make a 4:1 RGB multiplexer. A
circuit for this is shown in Figure 40. Each RGB source is connected to either the three “A” or “B” inputs of one of the
AD8185s. In addition, all R signals are tied to “0” inputs, all
G signals are tied to “1” inputs, and all B signals are tied to “2”
inputs. All of these input signals should be terminated with the
standard 75 Ω to ground very close to the IC pins.
EVALUATION BOARD
POWER AND GROUND
There are three power supply pins on the board. “VCC” is +5 V
analog, “V EE” is –5 V analog, and “DVCC” is +5 V digital.
These three power supply pins should be connected to good
quality, low noise supplies. If the same ± 5 V power supply is
used for both analog and digital, separate cables should be run
from the power supply to the evaluation board’s analog and digital
power supply pins.
Each of the outputs of the AD8185 has a series 75 Ω resistor to
provide a back termination for the monitor load. Whichever
device is selected will drive the output signal through its three
termination resistors. When terminated by the monitor, the
voltage of these signals will be attenuated by a factor of two.
This is normalized by the gain-of-two of the AD8185.
Unlike many gain-of-two circuits, the impedance of the AD8185
is very high when it is disabled. This is due to a proprietary
circuit that disconnects the feedback network from a low impedance when the part is disabled.
75V
R
IN0A
IN0B
G
75V
OE
OUT0
OE
OUT1
RED
75V
B
75V
SOURCE 0
IN1A
IN1B
75V
75V
GREEN
The RC in the OE circuit is to ensure “Break-Before-Make”
operation. Using the values shown, a 20 ns time constant is
created. This will delay the enabling of the outputs of the new
selection until after the other devices’ outputs are disabled. This
time can be shortened or eliminated if the system can tolerate
the glitches caused by simultaneously enabled outputs.
Three 10 µF tantalum capacitors (C1–C3) are located under the
power connector to decouple the power supplies as they first
enter the board. As the three supplies get close to the part, they
are again decoupled with 0.1 µF ceramic capacitors (C4–C6).
Finally, each power pin of the device is locally decoupled with a
0.01 µF ceramic capacitor (C7–C15).
The board has a separate analog and digital ground plane. With
the jumper at W5 installed, these two ground planes are tied
together on the board. Generally, this jumper should remain
installed.
TO
MONITOR
R
INPUTS AND OUTPUTS
75V
G
IN2A
IN2B
B
75V
75V
OE
BLUE
OUT2
SEL A/B
SOURCE 1
OE
200V
100pF
75V
R
IN0A
IN0B
G
75V
OE
OUT0
OE
OUT1
75V
The evaluation board has been carefully laid out to demonstrate
the high speed performance of the device. Optimized for video
applications, all signal inputs are terminated with 75 Ω resistors
to ground (R1–R6). The three outputs are backterminated with
75 Ω series resistors (R12–R14). Stripline techniques are used
to achieve a 75 Ω characteristic impedance on the input and
output lines. See Figure 41 for the arrangement of the PCB
layers.
B
SOURCE 2
75V
IN1A
IN1B
0.005" (127mm)
75V
TOP LAYER
75V
0.0176" (447mm)
R
75V
G
IN2A
IN2B
B
75V
SOURCE 3
75V
OE
0.028" (711mm)
OUT2
0.005" (127mm)
50V
SIGNAL LAYER
SEL 1
0.0038" (96.5mm)
200V
100pF
Figure 40. 4:1 RGB Multiplexer
Two control bits are required to select the input source for the
RGB signals. One is applied to each of the SEL A/B inputs of
each device to select between the two input sources for that
device. The other bit controls the OE inputs of the two devices.
REV. 0
75V
SIGNAL LAYER
POWER
LAYER
SEL A/B
OE
SEL 0
0.0026" (66mm)
Figure 41. PCB Dimensions
In addition, 75 Ω BNC connectors are used on the six inputs
(J1–J6) and three outputs (J7–J9). The connectors are arranged
in a crescent around the device. This results in all the input and
output signal traces having the same length. Unused regions of
the multilayer board are filled up with ground planes. As a
–11–
AD8183/AD8185
result, the input and output traces, in addition to having a controlled impedance, are well shielded.
41 for the arrangement of the PCB layers. If J10 is used, the
user may wish to install a 50 Ω termination resistor at R10.
OE (Pin 23 of the device) allows the three outputs to be enabled
or disabled. When OE is at logic low, (equal to or less than
0.8 V), Outputs 0, 1, and 2 are enabled. When OE is at logic
high, (equal to or greater than 2.0 V), Outputs 0, 1, and 2 are
disabled (placed into a high impedance state).
SEL A/B AND OE
SEL A/B (Pin 22 of the device) allows the A or B inputs to be
selected.
When SEL A/B is at logic low, (equal to or less than 0.8 V),
inputs 0A, 1A and 2A are directed to OUTPUTs 0, 1, and 2,
respectively. When SEL A/B is at logic high, (equal to or greater
than 2.0 V), inputs 0B, 1B, and 2B are directed to OUTPUTs
0, 1, and 2, respectively.
Once again, there are two different ways to provide OE to the
device: using a jumper or a BNC connection. With the jumper
in the W2 position, OE is tied to ground. This enables the outputs.
With the jumper in the W1 position, OE is tied to 5 V, through
pull-up resistor R16. This selects “Hi Z,” or high impedance,
and the outputs are disabled.
There are two ways to provide SEL A/B to the device: using a
jumper or a BNC connection. With the jumper in the W4 position, SEL A/B is tied to ground. This selects the A inputs.
If faster use of OE is desired, the 50 Ω BNC connector at J11
can be used. If J11 is used, there must NOT be a jumper on W1
and W2. Microstrip line techniques provide a 50 Ω characteristic impedance from J11 to the device. Please refer to Figure 41
for the arrangement of the PCB layers. If J11 is used, the user
may wish to install a 50 Ω termination resistor at R11.
With the jumper in the W3 position, SEL A/B is tied to 5 V,
through pull up resistor R15. This selects the B inputs.
If faster use of SEL A/B is desired, the 50 Ω BNC connector at
J10 can be used. If J10 is used, there must NOT be a jumper on
W3 and W4. Microstrip line techniques provide a 50 Ω characteristic impedance from J10 to the device. Please refer to Figure
DVCC
DVCC
P1
1
DVCC
+
C3
10mF
C6
0.1mF
DGND
DGND
DGND
DGND
P1
2
DGND
VEE
VEE
P1
VEE
4
+
C2
10mF
C5
0.1mF
AGND
AGND
AGND
AGND
P1
5
AGND
VCC
VCC
VCC
P1
VCC
VCC
6
+
R16
20kV
C1
10mF
C4
0.1mF
AGND
AGND
R15
20kV
W1
OE
W3
W2
W4
DGND
OE
IN0A
J1
50V MICROSTRIP LINE
75V STRIPLINE
J2
75V STRIPLINE
AGND
IN2A
J3
75V STRIPLINE
R3
75V
AGND
3
VCC
VEE
AGND
C7
0.01mF
AGND
IN2B
J4
J5
C8
0.01mF
4
5
6
AGND
7
75V STRIPLINE
R4
75V
8
AGND
9
10
AGND
IN1B
DGND
2
75V STRIPLINE
R5
75V
AGND
11
12
J6
R14
75V
VCC 24
IN0A
23
OE
DGND
22
IN1A
SEL A/B
21
AGND
VCC
20
IN2A
OUT0
19
VCC AD8183/ VEE
18
VEE AD8185 OUT1
VCC 17
IN2B
OUT2 16
AGND
15
VEE
IN1B
14
DVCC
AGND
VCC 13
IN0B
W5
75V STRIPLINE
J8
OUT1
J7
OUT2
VEE
C13
0.01mF
AGND
R13
75V
75V STRIPLINE
VCC
C12
0.01mF
AGND
R12
75V
75V STRIPLINE
VEE
DVCC
VCC
C9
0.01mF
AGND
IN0B
OUT0
AGND
DUT
AGND
J9
VCC
C14
0.01mF
C15
0.01mF
1
SEL A/B
DGND
VCC
R2
75V
J10
R10
50V
OPTIONAL
DGND
R1
75V
AGND
IN1A
50V MICROSTRIP LINE
J11
R11
50V
OPTIONAL
SEL A/B
DGND
AGND
C10
0.01mF
DGND
C11
0.01mF
AGND
75V STRIPLINE
R6
75V
AGND
DGND
AGND
Figure 42.␣ Evaluation Board Schematic
–12–
REV. 0
AD8183/AD8185
Figure 43. Component Side Silkscreen
Figure 44. Board Layout (Component Side)
REV. 0
–13–
AD8183/AD8185
Figure 45. Board Layout (75 Ω Signal Layer)
Figure 46. Board Layout (Ground Plane)
–14–
REV. 0
AD8183/AD8185
Figure 47. Board Layout (Circuit Side;) 50 Ω Signal Layer
Figure 48. Circuit Side Silkscreen
REV. 0
–15–
AD8183/AD8185
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
24-Lead Plastic TSSOP
(RU-24)
24
C3689–5–10/99
0.311 (7.90)
0.303 (7.70)
13
0.177 (4.50)
0.169 (4.30)
0.256 (6.50)
0.246 (6.25)
1
12
PIN 1
SEATING
PLANE
0.0433 (1.10)
MAX
0.0256 (0.65) 0.0118 (0.30)
BSC
0.0075 (0.19)
0.0079 (0.20)
0.0035 (0.090)
88
08
0.028 (0.70)
0.020 (0.50)
PRINTED IN U.S.A.
0.006 (0.15)
0.002 (0.05)
–16–
REV. 0