74AC240 OCTAL BUS BUFFER WITH 3 STATE OUTPUTS (INVERTED) ■ ■ ■ ■ ■ ■ ■ ■ ■ HIGH SPEED: tPD = 4.2ns (TYP.) at VCC = 5V LOW POWER DISSIPATION: ICC = 4µA(MAX.) at TA=25°C HIGH NOISE IMMUNITY: VNIH = V NIL = 28 % VCC (MIN.) 50Ω TRANSMISSION LINE DRIVING CAPABILITY SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 24mA (MIN) BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL OPERATING VOLTAGE RANGE: VCC (OPR) = 2V to 6V PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 240 IMPROVED LATCH-UP IMMUNITY DESCRIPTION The 74AC240 is an advanced high-speed CMOS OCTAL BUS BUFFER (3-STATE) fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS tecnology. G control input governs four BUS BUFFERs. DIP SOP TSSOP ORDER CODES PACKAGE TUBE DIP SOP TSSOP 74AC240B 74AC240M T&R 74AC240MTR 74AC240TTR This device is designed to be used with 3 state memory address drivers, etc. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. PIN CONNECTION AND IEC LOGIC SYMBOLS April 2001 1/9 74AC240 INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN No SYMBOL 1 2, 4, 6, 8 9, 7, 5, 3 11, 13, 15, 17 18, 16, 14, 12 19 10 20 1G 1A1 to 1A4 2Y1 to 2Y4 2A1 to 2A4 Output Enable Input Data Inputs Data Outputs Data Inputs 1Y1 to 1Y4 Data Outputs 2G GND VCC NAME AND FUNCTION Output Enable Input Ground (0V) Positive Supply Voltage TRUTH TABLE INPUTS OUTPUT G An Yn L L H L H X H L Z X : Don’t Care Z : High Impedance ABSOLUTE MAXIMUM RATINGS Symbol V CC Parameter Supply Voltage Value Unit -0.5 to +7 V VI DC Input Voltage -0.5 to VCC + 0.5 V VO DC Output Voltage IIK DC Input Diode Current -0.5 to VCC + 0.5 ± 20 mA IOK DC Output Diode Current ± 20 mA IO DC Output Current ± 50 mA ICC or IGND DC VCC or Ground Current Tstg Storage Temperature TL Lead Temperature (10 sec) V ± 400 mA -65 to +150 °C 300 °C Absolute Maximum Ratings are those values beyond which damage to the device may occour. Functional operation under these conditions is not implied. RECOMMENDED OPERATING CONDITIONS Symbol V CC Parameter Supply Voltage Unit 2 to 6 V VI Input Voltage 0 to VCC V VO Output Voltage 0 to VCC V Top Operating Temperature dt/dv Input Rise and Fall Time VCC = 3.0, 4.5 or 5.5V (note 1) 1) VIN from 30% to 70% of VCC 2/9 Value -55 to 125 °C 8 ns/V 74AC240 DC SPECIFICATIONS Test Condition Symbol VIH V IL VOH VOL II Ioz ICC IOLD IOHD Parameter High Level Input Voltage Low Level Input Voltage High Level Output Voltage Low Level Output Voltage TA = 25°C VCC (V) 3.0 4.5 5.5 3.0 4.5 5.5 Value VO = 0.1 V or VCC-0.1V Min. Typ. 2.1 3.15 3.85 1.5 2.25 2.75 1.5 2.25 2.75 VO = 0.1 V or VCC-0.1V Max. -40 to 85°C -55 to 125°C Min. Min. Max. 2.1 3.15 3.85 0.9 1.35 1.65 Max. 2.1 3.15 3.85 0.9 1.35 1.65 V 0.9 1.35 1.65 3.0 IO=-50 µA 2.9 2.99 2.9 2.9 4.5 IO=-50 µA 4.4 4.49 4.4 4.4 5.49 Unit 5.5 IO=-50 µA 5.4 5.4 5.4 3.0 IO =-12 mA 2.56 2.46 2.4 4.5 IO =-24 mA 3.86 3.76 3.7 5.5 IO =-24 mA 4.86 4.76 4.7 3.0 IO=50 µA 0.002 0.1 0.1 0.1 4.5 IO=50 µA 0.001 0.1 0.1 0.1 5.5 IO=50 µA 0.001 0.1 0.1 0.1 3.0 IO =12 mA 0.36 0.44 0.5 4.5 IO =24 mA 0.36 0.44 0.5 5.5 IO =24 mA 0.36 0.44 0.5 V V V Input Leakage Current High Impedance Output Leakage Current Quiescent Supply Current 5.5 VI = VCC or GND ± 0.1 ±1 ±1 µA 5.5 VI = VIH or VIL VO = VCC or GND ± 0.5 ± 2.5 ±5 µA 5.5 VI = VCC or GND 4 40 80 µA Dynamic Output Current (note 1, 2) 5.5 VOLD = 1.65 V max 75 50 mA VOHD = 3.85 V min -75 -50 mA 1) Maximum test duration 2ms, one output loaded at time 2) Incident wave switching is guaranteed on transmission lines with impedances as low as 50Ω 3/9 74AC240 AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, RL = 500 Ω, Input tr = tf = 3ns) Test Condition Symbol Parameter tPLH tPHL Propagation Delay Time tPZL tPZH Output Enable Time tPLZ tPHZ Output Disable Time Value TA = 25°C VCC (V) -40 to 85°C -55 to 125°C Min. Typ. Max. Min. Max. Min. Max. (*) 1.5 5.7 8.0 1.5 9.0 1.5 11.0 (**) 5.0 1.5 4.2 6.5 1.5 7.0 1.5 8.5 3.3 (*) 1.5 7.0 10.5 1.5 11.0 1.5 13.0 5.0(**) 1.5 5.0 8.0 1.5 8.5 1.5 10.5 3.3 (*) 1.5 7.0 10.5 1.5 11.5 1.5 13.5 (**) 1.5 6.5 9.0 1.5 9.5 1.5 11.0 3.3 5.0 Unit ns ns ns (*) Voltage range is 3.3V ± 0.3V (**) Voltage range is 5.0V ± 0.5V CAPACITIVE CHARACTERISTICS Test Condition Symbol Parameter CIN Input Capacitance C OUT Output Capacitance Power Dissipation Capacitance (note 1) C PD TA = 25°C VCC (V) Min. 5.0 Typ. Max. -40 to 85°C -55 to 125°C Min. Min. Max. pF pF 9 fIN = 10MHz Unit Max. 5 5.0 5.0 Value 21 pF 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/8 (per circuit) TEST CIRCUIT TEST SWITCH tPLH, tPHL Open tPZL, tPLZ 2V CC tPZH, tPHZ Open C L = 50pF or equivalent (includes jig and probe capacitance) R L = R1 = 500Ω or equivalent R T = ZOUT of pulse generator (typically 50Ω) 4/9 74AC240 WAVEFORM 1: PROPAGATION DELAYS (f=1MHz; 50% duty cycle) WAVEFORM 2: OUTPUT ENABLE AND DISABLE TIME (f=1MHz; 50% duty cycle) 5/9 74AC240 Plastic DIP-20 (0.25) MECHANICAL DATA mm DIM. MIN. a1 0.254 B 1.39 TYP. inch MAX. MIN. TYP. MAX. 0.010 1.65 0.055 0.065 b 0.45 0.018 b1 0.25 0.010 D 25.4 1.000 E 8.5 0.335 e 2.54 0.100 e3 22.86 0.900 F 7.1 0.280 I 3.93 0.155 L Z 3.3 0.130 1.34 0.053 P001J 6/9 74AC240 SO-20 MECHANICAL DATA mm DIM. MIN. TYP. A a1 inch MAX. MIN. TYP. 2.65 0.10 0.104 0.20 a2 MAX. 0.004 0.007 2.45 0.096 b 0.35 0.49 0.013 0.019 b1 0.23 0.32 0.009 0.012 C 0.50 0.020 c1 45 (typ.) D 12.60 13.00 0.496 0.512 E 10.00 10.65 0.393 0.419 e 1.27 0.050 e3 11.43 0.450 F 7.40 7.60 0.291 0.299 L 0.50 1.27 0.19 0.050 M S 0.75 0.029 8 (max.) P013L 7/9 74AC240 TSSOP20 MECHANICAL DATA mm DIM. MIN. inch TYP. MAX. A MIN. TYP. 1.1 0.433 A1 0.05 0.10 0.15 0.002 0.004 0.006 A2 0.85 0.9 0.95 0.335 0.354 0.374 b 0.19 0.30 0.0075 0.0118 c 0.09 0.2 0.0035 0.0079 D 6.4 6.5 6.6 0.252 0.256 0.260 E 6.25 6.4 6.5 0.246 0.252 0.256 E1 4.3 4.4 4.48 0.169 0.173 0.176 e 0.65 BSC 0.0256 BSC K 0o 4o 8o 0o 4o 8o L 0.50 0.60 0.70 0.020 0.024 0.028 A A2 A1 b K e E1 PIN 1 IDENTIFICATION 1 L E c D 8/9 MAX. 74AC240 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringe ment of patents or other righ ts of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this pub lication are subject to change without notice. Thi s pub lication supersedes and replaces all information previously supplied. STMicroelectronics prod ucts are not authori zed for use as critical components in life suppo rt devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics 2001 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Swit zerland - United Kingdom http://w ww.st.com 9/9