P R OPR IE TAR Y NOTE THIS SPECIFICATION IS THE PROPERTY OF HYDIS AND SHALL NOT BE REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF HYDIS AND MUST BE RETURNED TO HYDIS UPON ITS REQUEST TITLE : HV101HD1 - 1E1 Preliminary Product Specification FOR MORE INFORMATION: AZ DISPLAYS, INC. 75 COLUMBIA, ALISO VIEJO, CA 92656 PHONE: (949) 360 5830 E-MAIL: [email protected] Website: www.azdisplays.com HYDIS Technologies SPEC. NUMBER TD-0008247 (1/3) PRODUCT GROUP TFT LCD REV. P0 ISSUE DATE 2012. 05. 23 PAGE 1 OF 30 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2012. 05. 23 DATE PREPARED 12. 05. 23 SH Kim REVISION HISTORY REV. ECN NO. P0 SPEC. NUMBER TD-0008247 (2/3) DESCRIPTION OF CHANGES Initial Release SPEC TITLE HV101HD1-1E1 Preliminary Product Specification PAGE 2 OF 30 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2012. 05. 23 Contents No Item Page 1.0 General Description 4 2.0 Absolute Maximum Ratings 6 3.0 Electrical Specifications 7 4.0 Optical Specifications 11 5.0 Interface Connections 16 6.0 Signal Timing Specifications 19 7.0 Signal Timing Waveforms 19 8.0 Input Signals, Basic Display Colors & Gray Scale of Colors 20 9.0 Power Sequence 21 10.0 Mechanical Characteristics 22 11.0 Mechanical Drawing 23 12.0 Reliability Test 25 13.0 Handling & Cautions 26 14.0 Labels 27 15.0 Packing Information 29 SPEC. NUMBER TD-0008247 (3/3) SPEC TITLE HV101HD1-1E1 Preliminary Product Specification PAGE 3 OF 30 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2012. 05. 23 1.0 GENERAL DESCRIPTION 1.1 Introduction HV101HD1-1E1 is a color active matrix TFT LCD module using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This module has a 10.1 inch diagonally measured active area with HD resolutions (1366 horizontal by 768 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical Stripe and this module can display 16.7M colors. The TFT-LCD panel used for this module is a low reflection and higher color type. LVDS Input Signal DC/DC VLED LED_EN PWM Connector (CN1) VDD Back Light (SMD LED Array) TCON Gate Driver LED_PWM LED Driver TFT LCD Panel 1366×RGB X 768 Source Driver Anode/Cathode 1.2 Features FAB Site : CPT 3.3 V Logic Power LVDS Interface (1channel) 16.7M Colors (8bit) Data Enable Signal Mode SMD LED (36EA) Bottom alignment Green Product (RoHS) & Halogen free SPEC. NUMBER TD-0008247 (3/3) SPEC TITLE HV101HD1-1E1 Preliminary Product Specification PAGE 4 OF 30 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2012. 05. 23 1.3 Application industrial tablet 1.4 General Specifications < Table 1. General Specifications > Parameter Specification Unit Active area 223.341(H) ×125.568(V) mm Number of pixels 1366(H) ×RGB X 768(V) pixels Pixel pitch 0.1635 × 0.1635 Pixel arrangement RGB Vertical Stripe Display colors 16.7M (8bit) Display mode Normally Black Outline dimension 234.53.0.3(H)×138.970.3(V)×2.40.2(D) Weight 115 (Max.) Back-light Bottom alignment, 36-LEDs type SPEC. NUMBER TD-0008247 (3/3) SPEC TITLE HV101HD1-1E1 Preliminary Product Specification Remark mm colors mm g PAGE 5 OF 30 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2012. 05. 23 2.0 ABSOLUTE MAXIMUM RATINGS The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. Ta=25+/-2°C < Table 2. Absolute Maximum Ratings > Parameter Symbol Min. Max. Unit Logic Power Supply Voltage VDD -0.3 4.0 V Logic Power Supply Voltage VCC -0.3 2.0 V HVDD -0.3 40 V 30.0 mA Back-light Power Supply Voltage Back-light LED Current ILED Back-light LED Reverse Voltage VR - TBD V Operating Temperature TOP -0 +50 ℃ Storage Temperature TSP -20 +60 ℃ Remarks Note 1 Note 1, Note 2 Note 1. Ambient temperature vs allowable forward current are shown in the figure below. Note 2. Temperature and relative humidity range are shown in the figure below. 90% RH Max. ( 40℃ ≥ Ta) Maximum wet - bulb temperature at 39℃ or less. ( > 40℃) No condensation. SPEC. NUMBER TD-0008247 (3/3) SPEC TITLE HV101HD1-1E1 Preliminary Product Specification PAGE 6 OF 30 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2012. 05. 23 3.0 ELECTRICAL SPECIFICATIONS 3.1 Electrical Specifications < Table 3. Electrical Specifications > Parameter Min. Typ. Ma x. Unit Logic Power Supply Voltage VDD - 3.3 - V Logic Power Supply Current IDD - TBD - mA Back-light LED Voltage / Back-light LED Total Voltage VLED /VBL 2.8/ 16.8 2.9/ 17.4 3.0/ 18.0 V Back-light LED Current / Back-light LED Total Current ILED /IBL - 17/ 102 - mA PDD - TBD - W Pcc - TBD - W PBL 2.02 2.10 2.16 W Power Consumption Remarks Vdd=3.3V, 25℃ Note 1 Note 2 Notes : 1. The supply voltage is measured and specified at the interface connector of LCM. ( Test Pattern : White) 2. Calculated value for reference (VLED × ILED × # of LEDs (36EA) ). This value is with LED driver efficiency (85%) SPEC. NUMBER TD-0008247 (3/3) SPEC TITLE HV101HD1-1E1 Preliminary Product Specification PAGE 7 OF 30 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2012. 05. 23 3.2 PWM Duty Ratio vs Brightness 100 Relative Brightness (%) 90 80 70 60 50 40 30 20 10 0 0 10 20 30 40 50 60 70 80 90 100 Duty Ratio (%) Notes : In case of duty ratio 0%, LED can’t illuminate itself so this state is LED off. In case of duty ratio 100%, the brightness of LED is maximum and the state is LED on. SPEC. NUMBER TD-0008247 (3/3) SPEC TITLE HV101HD1-1E1 Preliminary Product Specification PAGE 8 OF 30 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2012. 05. 23 3.3 LVDS Interface The specification of the LVDS Rx interface timing parameter < Table 9, LVDS Rx Interface Timing Specification> Item Symbol Min. Typ. Max. Unit Remarks CLKIN Period tRCIP - 12.43 - nsec Input Data 0 tRIP0 -0.4 0.0 +0.4 nsec Input Data 1 tRIP1 tRICP/7-0.4 tRICP/7 tRICP/7+0.4 nsec Input Data 2 tRIP2 2 ×tRICP/7-0.4 2 ×tRICP/7 2 ×tRICP/7+0.4 nsec Input Data 3 tRIP3 3 ×tRICP/7-0.4 3 ×tRICP/7 3 ×tRICP/7+0.4 nsec Input Data 4 tRIP4 4 ×tRICP/7-0.4 4 ×tRICP/7 4 ×tRICP/7+0.4 nsec Input Data 5 tRIP5 5 ×tRICP/7-0.4 5 ×tRICP/7 5 ×tRICP/7+0.4 nsec Input Data 6 tRIP6 6 ×tRICP/7-0.4 6 ×tRICP/7 6 ×tRICP/7+0.4 nsec tRIP6 tRIP5 tRIP4 tRIP3 tRIP2 tRIP1 tRIP0 RxINz +/* Z = 0, 1, 2 Rx RxCLKIN+/- Rx Rx Rx Rx Vdiff=0[v] Rx Rx Rx Rx Rx Rx Vdiff=0[v] tRCIP SPEC. NUMBER TD-0008247 (3/3) SPEC TITLE HV101HD1-1E1 Preliminary Product Specification PAGE 9 OF 30 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2012. 05. 23 4.0 OPTICAL SPECIFICATIONS 4.1 Overview The test of optical specifications shall be measured in a dark room (ambient luminance 1 lux and temperature = 252℃) with the equipment of Luminance meter system (Goniometer system and TOPCON BM-5A) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of θ and Φ equal to 0. We refer to θØ =0 (=θ3 ) as the 3 o’clock direction (the “right”), θØ =90 (= θ12 ) as the 12 o’clock direction (“upward”), θØ =180 (= θ9 ) as the 9 o’clock direction (“left”) and θØ =270(= θ6 ) as the 6 o’clock direction (“bottom”). While scanning θ and/or Ø, the center of the measuring spot on the Display surface shall stay fixed. The backlight should be operating for 30 minutes prior to measurement. VDD shall be 3.3+/- 0.3V at 25C. 4.2 Optical Specifications Parameter Viewing Angle range <Table 6. Optical Specifications> Symbol Horizontal Vertical Luminance Contrast ratio Luminance of 1 Points White Θ3 Θ9 Θ12 Θ6 CR Yw White Luminance 9 Points uniformity ΔY9 White Chromaticity Wx Wy Rx Ry Gx Gy Bx By Red Reproduction of color Green Blue Condition Min. Typ. Max. 89 89 89 89 800 - Deg. Deg. Deg. Deg. Θ = 0 80 80 80 80 500 Θ = 0 350 400 - cd/m2 Note 4 75 - - % Note 4 CR > 10 TBD TBD 50 Θ = 0 Θ = 0 NTSC Unit Remarks Note 1 Note 2 % Note 3 Response Time Total (Tr + Td) Ta= 25 C Θ = 0 - - 30 ms Note 5 Cross Talk CT Θ = 0 - - 2.0 % Note 6 SPEC. NUMBER TD-0008247 (3/3) SPEC TITLE HV101HD1-1E1 Preliminary Product Specification PAGE 10 OF 30 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2012. 05. 23 Notes : 1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing angles are determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock direction with respect to the optical axis which is normal to the LCD surface (see Figure1). 2. Contrast measurements shall be made at viewing angle of Θ= 0 and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state (see Figure1). Luminance Contrast Ratio (CR) is defined mathematically as CR = Luminance when displaying a white raster / Luminance when displaying a black raster. 3. Reference only / Standard Front Surface Treatment Measured with green cover glass. The color chromaticity coordinates specified in Table 4 shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel. SPEC. NUMBER TD-0008247 (3/3) SPEC TITLE HV101HD1-1E1 Preliminary Product Specification PAGE 11 OF 30 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2012. 05. 23 4.3 Optical Measurements Figure 1. Measurement Set Up Photo detector ( TOPCON BM-5A) o Field = 1 50 cm TFT-LCD module LCD panel Center of the screen Optical characteristics measurement setup Figure 2. White Luminance and Uniformity Measurement Locations (9 points) Column 10mm 683 10mm Row 10mm 384 10mm Note 4. Luminance of white is defined as luminance values of 9 points across the LCD surface. Luminance shall be measured with all pixels in the view field set first to white. This measurement shall be taken at the locations shown in Figure 2 for a total of the measurements per display. * Yw = (Sum of 9 Points Luminance / 9 ) * LED Condition = (Duty Ratio 100%, LED current 17 mA) SPEC. NUMBER TD-0008247 (3/3) SPEC TITLE HV101HD1-1E1 Preliminary Product Specification PAGE 12 OF 30 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2012. 05. 23 Figure 3. Response Time Testing TFT Off(Black) TFT On(White) TFT Off(Black) Tr Td 100% 90% 10% 0% SPEC. NUMBER TD-0008247 (3/3) SPEC TITLE HV101HD1-1E1 Preliminary Product Specification PAGE 13 OF 30 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2012. 05. 23 Figure 4. Cross Modulation Test Description VIEW AREA VIEW AREA L31 480,300 960,300 YB(1680, 600) 480,600 YA (1680,600) Cross-Talk (%) = 960,600 L256 YB - YA × 100 YB Where: YA = Initial luminance of measured area (cd/m2) YB = Subsequent luminance of measured area (cd/m 2) The location measured will be exactly the same in both patterns Note 5. The electro-optical response time measurements shall be made as Figure 4 by switching the “data” input signal ON and OFF. The times needed for the luminance to change from 10% to 90% is Tr, and 90% to 10% is Td. Note 6. Cross-Talk of one area of the LCD surface by another shall be measured by comparing the luminance (YA) of a 25mm diameter area, with all display pixels set to a gray level, to the luminance (YB) of that same area when any adjacent area is driven dark (Refer to Figure 4). SPEC. NUMBER TD-0008247 (3/3) SPEC TITLE HV101HD1-1E1 Preliminary Product Specification PAGE 14 OF 30 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2012. 05. 23 5.0 INTERFACE CONNECTIONS 5.1 Electrical Interface Connection CN1 HYDIS side connector I-PEX : 20455-040E-12 < Table 7, Electrical Interface Connection > Pin No Symbol Function 1 NC NC (Please let it floating for test only) 2 VCC +3.3V Power 3 VCC +3.3V Power 4 V_EDID EDID 3.3V Power 5 NC NC (Please let it floating for test only) 6 CLK_EDID EDID Clock 7 DATA_EDID EDID Data 8 RXIN0- LVDS Signal(-)—channel 0 9 RXIN0+ LVDS Signal(+)—channel 0 10 GND Ground 11 RXIN1- LVDS Signal(-)—channel 1 12 RXIN1+ LVDS Signal(+)—channel 1 13 GND Ground 14 RXIN2- LVDS Signal(-)—channel 2 15 RXIN2+ LVDS Signal(+)—channel 2 16 GND Ground 17 RXCLKIN- LVDS Clock Signal(-) 18 RXCLKIN+ LVDS Clock Signal(+) 19 GND Ground 20 RXIN3- LVDS Signal(-)—channel 3 21 RXIN3+ LVDS Signal(+)—channel 3 SPEC. NUMBER TD-0008247 (3/3) SPEC TITLE HV101HD1-1E1 Preliminary Product Specification PAGE OF 30 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2012. 05. 23 < Table 7, Electrical Interface Connection > Pin No Symbol Function 22 GND Ground 23 NC NC (Please let it floating for test only) 24 NC NC (Please let it floating for test only) 25 GND Ground 26 NC NC (Please let it floating for test only) 27 NC NC (Please let it floating for test only) 28 GND Ground 29 NC NC (Please let it floating for test only) 30 NC NC (Please let it floating for test only) 31 VSSLED Ground – LED 32 VSSLED Ground – LED 33 VSSLED Ground – LED 34 NC NC (Please let it floating for test only) 35 PWM System PWM Signal Input (+3.3V Swing) 36 LED_EN LED enable pin (+3.3V Input) 37 NC NC (Please let it floating for test only) 38 VLED Power Supply for LED(VLED =4.5V ~ 21V) 39 VLED Power Supply for LED(VLED =4.5V ~ 21V) 40 VLED Power Supply for LED(VLED =4.5V ~ 21V) SPEC. NUMBER TD-0008247 (3/3) SPEC TITLE HV101HD1-1E1 Preliminary Product Specification PAGE 16 OF 30 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2012. 05. 23 5.2 Data Input Format (1, 1) (1365, 1) (1366, 1) (2, 1) R G B R G B R G B R G B 1 Pixel = 3 Dots R G B R G B R G B (1, 768) SPEC. NUMBER TD-0008247 (3/3) (2, 768) R G B R G B (1365, 768) (1366, 768) SPEC TITLE HV101HD1-1E1 Preliminary Product Specification PAGE 17 OF 30 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2012. 05. 23 6.0. SIGNAL TIMING SPECIFICATIONS 6.1 The LCM is operated by the only DE (Data enable) mode < Table 8. Signal Timing > Item Symbol Frame Rate Min. Typ. Max. Unit - 60 Hz Frame Period T1 838 Lines Vertical Display Time T2 768 Lines Vertical Blanking Time T3 70 Lines 1 Line Scanning Time T4 1600 Clocks Horizontal Display Time T5 1366 Clocks Horizontal Blanking Time T6 243 Clocks 1/T7 80.44 MHz Clock Rate Note 1. This value only guarantee for the circuit-operation 7.0 SIGNAL TIMING WAVEFORMS 7.1 Timing Waveforms of Interface Signal T1 T2 DE T3 DCLK T5 T4 DE DATA SIGNALS SPEC. NUMBER TD-0008247 (3/3) Valid display data (768 Clocks) SPEC TITLE HV101HD1-1E1 Preliminary Product Specification PAGE 18 OF 30 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2012. 05. 23 8.0 INPUT SIGNALS, BASIC DISPLAY COLORS & GRAY SCALE OF COLORS Each color is displayed in sixty-four gray scales from a 8 bit data signal input. Colors & Gray Scale Basic Colors Gray Scale Of Red Gray Scale Of Green Gray Scale Of Blue Gray Scale Of White & Black Black Blue Green Cyan Red Magenta Yellow White Black △ Darker △ ▽ Brighter ▽ Red Black △ Darker △ ▽ Brighter ▽ Green Black △ Darker △ ▽ Brighter ▽ Blue Black △ Darker △ ▽ Brighter ▽ White SPEC. NUMBER TD-0008247 (3/3) Red Data Green Data Blue Data R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 1 0 0 0 0 1 1 1 1 0 1 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 1 1 1 0 0 0 0 1 1 0 0 1 1 0 1 0 1 0 1 1 1 0 1 1 1 0 1 ↓ ↓ 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 ↓ ↓ 1 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ↓ ↓ 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 1 1 1 0 0 0 0 0 1 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ↓ ↓ 1 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ↓ ↓ 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ↓ ↓ 1 1 1 0 0 0 0 0 0 ↓ ↓ ↓ ↓ 0 0 0 0 0 0 ↓ ↓ ↓ ↓ 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 ↓ ↓ 1 1 1 0 1 1 1 0 1 1 1 1 1 1 1 1 1 1 ↓ ↓ 1 1 1 0 1 1 1 0 1 SPEC TITLE HV101HD1-1E1 Preliminary Product Specification 1 1 1 1 1 1 1 1 1 PAGE 19 OF 30 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2012. 05. 23 9.0 POWER SEQUENCE To prevent a latch-up or DC operation of the LCD module, the power on/off sequence shall be as shown in below 0.9VDD/0.9VCC Power Supply 0.9VDD/0.9VCC 0.1VDD/ 0.1VCC 0.1VDD/ 0.1VCC 0V T1 T5 T7 T2 T6 Interface Signal Valid 0V T3 Back- light T4 0V ● T1 10 ms ● 0 T2 50 ms ● 70 ms T3 ● 200 ms T4 ● 0 T5 ≤ 50 ms ● 0 T6 10ms ● 150ms T7 Notes : 1. When the power supply VDD/ VCC is 0V, Keep the level of input signals on the low or keep high impedance. 2. Do not keep the interface signal high impedance when power is on. 3. Back Light must be turn on after power for logic and interface signal are valid. SPEC. NUMBER TD-0008247 (3/3) SPEC TITLE HV101HD1-1E1 Preliminary Product Specification PAGE 20 OF 30 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2012. 05. 23 10.0 MECHANICAL CHARACTERISTICS 10.1 Dimensional Requirements Figure 5 & 6 shows mechanical outlines for the model < Table 9, Mechanical Characters > Parameter Specification Active Area 223.341(H) ×125.568(V) Number of pixels 1366(H) X 768(V) (1 pixel = R + G + B dots) Pixel pitch 0.1635(H) X 0.1635(V) Pixel arrangement RGB Vertical stripe Display colors 262K (6bits) Display mode Normally Black Outline dimension 234.53(H)×138.97(V)×2.4(D) (Typ.) Weight 115(Max.) Back-light Bottom alignment 36-LEDs type Unit mm mm mm g 10.2 LR and Polarizer Hardness. The surface of the LCD has an Clear and a coating to reduce scratching. 10.3 Light Leakage There shall not be visible light from the back-lighting system around the edges of the screen as seen from a distance 50cm from the screen with an overhead light level of 150lux. The manufacture shall furnish limit samples of the panel showing the light leakage acceptable. SPEC. NUMBER TD-0008247 (3/3) SPEC TITLE HV101HD1-1E1 Preliminary Product Specification PAGE 21 OF 30 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2012. 05. 23 11.0 Mechanical Drawing Figure 5. TFT-LCD Module Outline Dimension (Front View) 138.97 2.16 (to Pol.) 135.56 129.71±0.2 (Pol.) (7.1) 125.568 (active area) 35.618 4.52 (to Pol.) 62.784 2-11.91(D-IC) (67.01) (118.26) TOP BOTTOM 234.53±0.2 (Outline) 223.341±0.2 (2.52) Shield cover TD-0008247 (3/3) 231.94±0.2 227.49±0.2 (Pol.) Active Area Center 208.7 Shield Cover SPEC. NUMBER SPEC TITLE HV101HD1-1E1 Preliminary Product Specification PAGE 22 OF 30 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2012. 05. 23 Figure 6. TFT-LCD Module Outline Dimensions (Rear view) 120.39+2 0 (18.58) 15 103.97(B/C Hole) 15 5 Hydis Finished Goods Code(Printing) BARCODE AREA 85 Shield cover 20 5 TOP TBD BOTTOM 204.53(B/C Hole) 57.66 connector 1 21.82 connector (96.44) (14.3) 4.2±0.2 (w/ PCB) TD-0008247 (3/3) 2.4±0.2(w/o PCB) SPEC. NUMBER SPEC TITLE HV101HD1-1E1 Preliminary Product Specification PAGE 23 OF 30 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2012. 05. 23 12.0 RELIABLITY TEST The Reliability test items and its conditions are shown in below. < Table10, Reliability Test > No Test Item Test Condition High temperature storage test Low temperature storage test High temperature & high humidity operation test High temperature operation test Low temperature operation test Thermal shock Operating Ta = 60 C, 240 hrs No Ta = -20 C, 240 hrs No Ta = 50 ℃, 80%RH, 240hrs Yes Ta = 50 C, 240 hrs Yes Ta = 0 C, 240 hrs Yes Ta = -20 C 60 C (30 min), 100 cycle No 7 Vibration test (non-operating) Frequency : 10~500Hz Gravity/AMP : 1.5G Period : X,Y,Z 30min NO 8 Shock test (non-operating) Gravity : 220G Pulse width : 2ms, half sine wave ±X, ±Y, ±Z Once for each direction No 9 Electro-static discharge test (non-operating) C=150pF, R=330Ω, 5cycle/ Air 15KV, Contact 8kV 1 2 3 4 5 6 No Note 1 Note 1 : 1. ESD test condition is standard of customer system. SPEC. NUMBER TD-0008247 (3/3) SPEC TITLE HV101HD1-1E1 Preliminary Product Specification PAGE 24 OF 30 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2012. 05. 23 13.0 HANDLING & CAUTIONS 13.1 Cautions when taking out the module Pick the pouch only, when taking out module from a shipping package. 13.2 Cautions for handling the module As the electrostatic discharges may break the LCD module, handle the LCD module with care. Peel a protection sheet off from the LCD panel surface as slowly as possible. As the LCD panel and back - light element are made from fragile glass (epoxy) material, impulse and pressure to the LCD module should be avoided. As the surface of the polarizer is very soft and easily scratched, use a soft dry cloth without chemicals for cleaning. Do not pull the interface connector in or out while the LCD module is operating. Put the module display side down on a flat horizontal plane. Handle connectors and cables with care. 13.3 Cautions for the operation When the module is operating, do not lose MCLK, DE signals. If any one of these signals were lost, the LCD panel would be damaged. Obey the supply voltage sequence. If wrong sequence is applied, the module would be damaged. 13.4 Cautions for the atmosphere Dew drop atmosphere should be avoided. Do not store and/or operate the LCD module in a high temperature and/or humidity atmosphere. Storage in an electro-conductive polymer packing pouch and under relatively low temperature atmosphere is recommended. 13.5 Cautions for the module characteristics Do not apply fixed pattern data signal to the LCD module at product aging. Applying fixed pattern for a long time may cause image sticking. 13.6 Cautions for the digitizer assembly When assembling FPC connector, do not flip connector past 90° due to possible damage to connector. When positioning digitizer underneath driver IC, do not lift driver IC past 90° due to possible damage to drive IC pattern. Please be warned that during assembly of digitizer, the opening or closing of FPC will result in possible electrostatic discharge damage to the LED 13.7 Other cautions Do not re-adjust variable resistor or switch etc. When returning the module for repair or etc., Please pack the module not to be broken. We recommend to use the original shipping packages. SPEC. NUMBER TD-0008247 (3/3) SPEC TITLE HV101HD1-1E1 Preliminary Product Specification PAGE 25 OF 30 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2012. 05. 23 14.0 LABELS 14.1 Product Label Printing at Reflection sheet (LCM back side) Model : HV101HD1-1E1 1 R H V Output Factory 1 0 1 H D Hydis model name 0 0 0 2 1 BOM number 2 Week 0 1 0 4 Serial number R : T2 U : WJ LCM1 V : WJ LCM2 Year 2012 : 2 2013 : 3 SPEC. NUMBER TD-0008247 (3/3) SPEC TITLE HV101HD1-1E1 Preliminary Product Specification PAGE 26 OF 30 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2012. 05. 23 14.2 Packing Label SPEC. NUMBER TD-0008247 (3/3) SPEC TITLE HV101HD1-1E1 Preliminary Product Specification PAGE 27 OF 30 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2012. 05. 23 15.0 PACKING INFORMATION 15.1 Packing order Notes : 1. Box Dimension: TBD 2. Package Quantity in one Box : TBD SPEC. NUMBER TD-0008247 (3/3) SPEC TITLE HV101HD1-1E1 Preliminary Product Specification PAGE 28 OF 30 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT LCD PRODUCT P0 2012. 05. 23 15.2 Pallet Packing * Note Pallet Dimension : TBD Package Quantity in one Box : TBD Box Quantity in one Pallet : TBD SPEC. NUMBER TD-0008247 (3/3) SPEC TITLE HV101HD1-1E1 Preliminary Product Specification PAGE 29 OF 30 A4(210 X 297)