NSC DS15BA101

DS15BA101
1.5 Gbps Differential Buffer with Adjustable Output Voltage
General Description
Features
The DS15BA101 is a high-speed differential buffer for cable
driving, level translation, signal buffering, and signal repeating applications. Its fully differential signal path ensures exceptional signal integrity and noise immunity and it drives both
differential and single-ended transmission lines at data rates
up to 1.5 Gbps.
Output voltage amplitude is adjustable via a single external
resistor for level translation and cable driving applications into
50-ohm single-ended and 100-ohm differential mode
impedances.
The DS15BA101 is powered from a single 3.3V supply and
consumes 150 mW (typ) at 1.5 Gbps. The DS15BA101 operates over the full −40°C to +85°C industrial temperature
range and is available in a space saving 3x3 mm LLP-8 package.
■
■
■
■
■
■
■
Data rates from DC to 1.5 Gbps
Differential or single-ended input
Adjustable output amplitude
Single 3.3V supply
Industrial -40°C to +85°C temperature
Low power: 150 mW (typ) at 1.5 Gbps
Space-saving 3 x 3 mm LLP-8 package
Applications
■
■
■
■
■
■
■
Cable extension applications
Level translation
Signal buffering and repeating
Digital routers and switches
Sonet/SDH and ATM interfaces
Set top boxes
Security cameras
Typical Application
20199902
© 2006 National Semiconductor Corporation
201999
www.national.com
DS15BA101 1.5 Gbps Differential Buffer with Adjustable Output Voltage
December 2006
DS15BA101
ESD Rating (HBM)
ESD Rating (MM)
Absolute Maximum Ratings (Note 1)
Supply Voltage:
Input Voltage (all inputs)
Output Current
Storage Temperature Range
Junction Temperature
Lead Temperature
(Soldering 4 Sec)
Package Thermal Resistance
θJA LLP-8
θJC LLP-8
−0.5V to 3.6V
−0.3V to VCC+0.3V
28 mA
−65°C to +150°C
+150°C
5 kV
250V
Recommended Operating
Conditions
Supply Voltage (VCC – GND):
Operating Free Air Temperature (TA)
DS15BA101SD
+260°C
3.3V ±5%
−40°C to +85°C
+90.7°C/W
+41.2°C/W
DC Electrical Characteristics
Over Supply Voltage and Operating Temperature ranges, unless otherwise specified (Notes 2, 3).
Symbol Parameter
VICM
Input Common Mode Voltage
VID
Differential Input Voltage Swing
VOS
Output Common Mode Voltage
VOUT
Output Voltage
Conditions
Reference
Min
IN+, IN-
1.6 +
VID/2
100
OUT+, OUTSingle-ended, 50Ω load,RVO =
953Ω 1%,
Single-ended, 50Ω load,RVO =
487Ω 1%,
ICC
Supply Current
Typ
(Note 5)
Max
Units
VCC –
VID/2
V
2000
mVP−P
VCC –
VOUT
V
400
mVP-P
800
mVP-P
45
49
mA
Max
Units
AC Electrical Characteristics
Over Supply Voltage and Operating Temperature ranges, unless otherwise specified (Note 3).
Symbol Parameter
Conditions
Reference
Min
Typ
DRMAX
Maximum Data Rate
(Note 4)
IN+, IN-
1.5
2.0
tLHT
Output Low to High Transition
Time
20% – 80%, (Note 6)
OUT+, OUT-
tHLT
Output High to Low Transition
Time
tPLHD
Propagation Low to High Delay
(Note 4)
tPHLD
Propagation High to Low Delay
(Note 4)
tTJ
Total Jitter
1.5 Gbps
Gbps
120
220
ps
120
220
ps
0.95
1.10
1.35
ns
0.95
1.10
1.35
26
ns
psP-P
Note 1: "Absolute Maximum Ratings" are those parameter values beyond which the life and operation of the device cannot be guaranteed. The stating herein of
these maximums shall not be construed to imply that the device can or should be operated at or beyond these values. The table of "Electrical Characteristics"
specifies acceptable device operating conditions.
Note 2: Current flow into device pins is defined as positive. Current flow out of device pins is defined as negative. All voltages are stated referenced to GND.
Note 3: Typical values are stated for VCC = +3.3V and TA = +25°C.
Note 4: Specification is guaranteed by characterization.
Note 5: Maximum ICC is measured at VCC = +3.465V and TA = +70°C.
Note 6: Specification is guaranteed by characterization and verified by test.
www.national.com
2
DS15BA101
Connection Diagram
20199901
8-Pad LLP
Order Number DS15BA101SD or DS15BA101SDX
See NS Package Number SDA08A
Pin Descriptions
Pin #
Name
Description
1
IN+
Non-inverting input pin.
2
IN-
Inverting input pin.
3
GND
Circuit common (ground reference).
4
RVO
Output voltage amplitude control. Connect a resistor to VCC to set output voltage.
5
VCC
Positive power supply (+3.3V).
6
GND
Circuit common (ground reference).
7
OUT-
Non-inverting output pin.
8
OUT+
Inverting output pin.
Device Operation
cable (with RVO = 953Ω) or into AC-coupled 50Ω coaxial cable
(with RVO = 487Ω). Output level is controlled by the value of
the RVO resistor connected between the RVO and VCC.
The RVO resistor should be placed as close as possible to the
RVO pin. In addition, the copper in the plane layers below the
RVO network should be removed to minimize parasitic capacitance.
INPUT INTERFACING
The DS15BA101 accepts either differential or single-ended
input. The inputs are self-biased, allowing for simple AC or
DC coupling. DC-coupled inputs must be kept within the specified common-mode range. The IN+ and IN- are self-biased
at approximately 2.1V with VCC = 3.3V.
OUTPUT INTERFACING
The DS15BA101 uses current mode outputs. Single-ended
output levels are 400 mVP-P into AC-coupled 100Ω differential
3
www.national.com
DS15BA101
Physical Dimensions inches (millimeters) unless otherwise noted
8-Pad LLP
Order Number DS15BA101SD or DS15BA101SDX
NS Package Number SDA08A
www.national.com
4
DS15BA101
Notes
5
www.national.com
DS15BA101 1.5 Gbps Differential Buffer with Adjustable Output Voltage
Notes
THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION
(“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY
OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO
SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS,
IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS
DOCUMENT.
TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT
NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL
PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR
APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND
APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE
NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS.
EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO
LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE
AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR
PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY
RIGHT.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and
whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected
to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform
can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.
National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other
brand or product names may be trademarks or registered trademarks of their respective holders.
Copyright© 2006 National Semiconductor Corporation
For the most current product information visit us at www.national.com
National Semiconductor
Americas Customer
Support Center
Email:
[email protected]
Tel: 1-800-272-9959
www.national.com
National Semiconductor Europe
Customer Support Center
Fax: +49 (0) 180-530-85-86
Email: [email protected]
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +49 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
National Semiconductor Asia
Pacific Customer Support Center
Email: [email protected]
National Semiconductor Japan
Customer Support Center
Fax: 81-3-5639-7507
Email: [email protected]
Tel: 81-3-5639-7560