http://www.elecfans.com 电子发烧友 http://bbs.elecfans.com 电子技术论坛 OB2203 Quasi-Resonant Flyback PWM Controller GENERAL DESCRIPTION OB2203 is a highly integrated Quasi-Resonant (QR) controller optimized for high performance offline flyback converter applications. At normal load condition, it operates in QR mode with minimum drain voltage switching. To meet the CISPR-22 EMI starting at 150KHz, the maximum switching frequency is internally limited to 130KHz. It operates in PFM mode for high power conversion efficiency at light load condition. When the loading is very small, the IC operates in ‘Extended Burst Mode’ to minimize the switching loss. As a result, lower standby power consumption and higher conversion efficiency is achieved. A built-in P-channel MOSFET and its control are integrated to automatically turn on or off PFC stage according to the load conditions. When used with OB6563 (On-Bright’s PFC controller), the standby power consumption of less than 400mW can be achieved in typical 150W SMPS. OB2203 offers comprehensive protection coverage including Cycle-by-Cycle Current Limiting(OCP), VCC Under Voltage Lockout(UVLO), Over Voltage Protection(OVP), VCC Clamp, Gate Clamp, Over Load Protection(OLP), On-chip Thermal Shutdown, Programmable Soft Start, and External Latch Triggering, Max On-time Limit, etc. OB2203 is offered in SOP-8 and DIP-8 packages. FEATURES ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Multi-Mode Operation Quasi-Resonant Operation at Normal Loading Pulse Frequency Modulation (PFM) Operation at Light Load Burst Mode at No Load Direct Control of the Power Supply of PFC Controller for Improved Standby Power at No/Light Load 40KHz Minimum Frequency Limit at QR Mode 130KHz Maximum Frequency Limit Internal Minimum T_off for Ringing Suppression 45us Maximum On Time Limit Adaptive Slope Compensation Internal Leading Edge Blanking Programmable Soft-start External Latch Triggering Internal Temperature Shutdown 1A Peak Current Sink/Source Capability Programmable Over Voltage Protection (OVP) APPLICATIONS Offline AC/DC flyback converter for Power Adaptor and Open-frame SMPS ■ LCD Monitor/TV/PC/Set-Top Box Power Supplies ■ NB/DVD/Portable DVD Power Supplies ■ TYPICAL APPLICATION ©On-Bright Electronics Confidential -1- OB_DOC_DS_0300 OB2203 http://www.elecfans.com 电子发烧友 http://bbs.elecfans.com 电子技术论坛 Quasi-Resonant Flyback PWM Controller GENERAL INFORMATION Pin Configuration The pin map of OB2203 in DIP8 and SOP8 package is shown as below. Ordering Information Part Number Description 8 Pin DIP, Pb free in Tube OB2203AP 8 Pin SOP, Pb free in Tube OB2203CP 8 Pin SOP, Pb free in T&R OB2203CPA Note: All Devices are offered in Pb-free Package if not otherwise Package Dissipation Rating Package DIP8 SOP8 RθJA (°C/W) 90 150 Absolute Maximum Ratings Parameter Value VCC Zener Clamp Voltage 31 V 10 mA VCC Clamp Continuous Current SS Input Voltage -0.3 to 7V FB Input Voltage -0.3 to 7V CS Input Voltage -0.3 to 7V -0.3 to 7V DEM Input Voltage Min/Max Operating Junction -20 to 150 oC Temperature TJ Min/Max Storage Temperature -55 to 150 oC Tstg 260 oC Lead Temperature (Soldering, 10secs) Note: Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute maximum-rated conditions for extended periods may affect device reliability. noted. ©On-Bright Electronics Confidential -2- OB_DOC_DS_0300 http://www.elecfans.com 电子发烧友 http://bbs.elecfans.com 电子技术论坛 OB2203 Quasi-Resonant Flyback PWM Controller Marking Information SOP8 DIP8 LT LT YWW YWW OB2203AP OB2203CP s s Y: Year Code (0-9) Y: Year Code (0-9) WW: Week Code (1-52) WW: Week Code (1-52) C: SOP8 A: DIP8 P:lead-free P:lead-free s: internal code s: internal code TERMINAL ASSIGNMENTS Pin Num 1 Pin Name SS I/O I/O 2 FB I/O 3 4 5 6 7 CS GND GATE VCC PFCVCC I O O P P 8 DEM I/O Description Soft-start programming pin. Program the soft-start rate with a capacitor to ground. After soft-start, the pin’s voltage is clamped at 2V. External latch input, latch will be triggered when SS pin voltage higher than 3.8V. Feedback input pin. PWM duty cycle is determined by voltage level into this pin and current-sense signal level at Pin 3. The voltage level at this pin also controls the mode of operation in one of the three modes: quasi-resonant (QR), pulse frequency modulation mode (PFM) and burst mode (BM). Current sense input. Ground for internal circuitry. Totem-pole gate drive output for power MOSFET. Chip DC power supply pin. This pin is a direct connection to the VCC pin via a low impedance switch. In standby and during the startup sequence, the switch is open and the PFCVCC is shut down. As soon as the auxiliary winding is stabilized, PFCVCC connects to the VCC pin and provides power supply to PFC controller. It goes down in any fault or at No/Light conditions. Input from auxiliary winding for demagnetization timing. Also this pin is used for load over voltage protection (OVP). ©On-Bright Electronics Confidential -3- OB_DOC_DS_0300 http://www.elecfans.com 电子发烧友 http://bbs.elecfans.com 电子技术论坛 OB2203 Quasi-Resonant Flyback PWM Controller BLOCK DIAGRAM RECOMMENDED OPERATING CONDITION Symbol VCC TA Parameter VCC Supply Voltage Operating Ambient Temperature Min 12 -20 ©On-Bright Electronics Max 23 85 Unit V o C Confidential -4- OB_DOC_DS_0300 OB2203 http://www.elecfans.com 电子发烧友 http://bbs.elecfans.com 电子技术论坛 Quasi-Resonant Flyback PWM Controller ELECTRICAL CHARACTERISTICS (TA = 25OC, VCC=16V, if not otherwise noted) Symbol Parameter Supply Voltage (VCC) Section VCC Start up Current I_VCC_Startup Operation Current without switching I_VCC_operation Operation current with switching UVLO(ON) VCC Under Voltage Lockout Enter VCC Under Voltage UVLO(OFF) Lockout Exit (Startup) OVP(ON) VCC Over Voltage Protection Enter VCC_Clamp VCC Zener Clamp Voltage Feedback Input Section(FB Pin) AVCS PWM Input Gain VFB_Open FB Open Voltage I_VCC_quiet FB pin short circuit current VTH_0D Zero Duty Cycle FB Threshold Voltage VTH_PFM_H PFM mode up threshold PFM mode down VTH_PFM_L threshold Burst Mode on VTH_BM_on threshold VTH_BM_off Burst Mode off threshold VTH_PFC_GTS Threshold for PFC to go to standby Threshold for PFC to VTH_PFC_on leave standby mode Power Limiting FB VTH_PL Threshold Voltage TD_PL Power limiting Debounce Time ZFB_IN Input Impedance Current Sense Input(CS Pin) Section T_blanking CS Input Leading Edge Blanking Time VTH_OC_0 Internal current limiting threshold Internal current VTH_OC_60% limiting threshold Over Current TD_OC IFB_Short Test Conditions Min Typ Max Unit VCC =13.5V, Measure current into VCC FB=3V, CS is floating, - 5 15 uA - 2.0 3.0 mA FB=3V, Fsw=40KHz, 1nF load at GATE - 3.0 4.0 mA 7.5 8.5 9.5 V 14 15 16 V 29 31 33 V I(VCC ) = 5 mA 30 32 34 V ΔVFB /ΔVcs 4.8 3.5 5.3 6.0 V/V V Short FB pin to GND, measure current 1.0 1.5 - mA 0.95 V 60 Zero duty cycle 0.43 1.45 V 1.0 V 1.0 V 0.9 V 1.35 V 1.45 V 4.4 V 80 mSec 4 Kohm 350 nSec 0.45 60% duty cycle 0.80 CL=1nf at GATE, 100 ©On-Bright Electronics 120 0.47 V V 160 nSec Confidential -5- OB_DOC_DS_0300 OB2203 http://www.elecfans.com 电子发烧友 http://bbs.elecfans.com 电子技术论坛 Quasi-Resonant Flyback PWM Controller Detection and Control Delay Demagnetization Detection Section VTH_DEM Demagnetization comparator threshold voltage Hysteresis for DEM VTH_DEM_hyst comparator Negative clamp VDEM_clamp(neg) voltage VDEM_clamp(pos) Positive clamp voltage Tsupp Suppression of the transformer ringing at start of secondary stroke Timeout after last TOUT demag transistion TDEM_delay Demag propagation delay VTH_OVP OVP trigger point OVP plateau T_ovp_plateau sampling after switching off N_true_OVP Number of subsequent cycles to be true OVP Soft Start Section Soft start charge Iss current VTH_ss_over Soft start over threshold voltage ISS_clamp_sink Maximum sink current capability when SS is clamped SS pin high clamp VSS_clamp voltage Timer Section F_burst Burst mode switching frequency F_QR_clamp_h Frequency high clamp in QR mode Frequency low clamp F_QR_clamp_l in QR mode Ton_max Maximum on time Toff_max Maximum off time G_PFM PFM mode frequency modulation slope versus control voltage Thermal Protection T_shutdown Thermal shutdown temperature Latch Protection V_latch_trigger Latch trigger threshod 10 75 30 20 mV -0.7 V 5.8 V 1.5 2 2.5 usec 4 5 6 usec 1.5 150 nsec 3.75 V 2 2.5 4 8.0 10 80 ©On-Bright Electronics 120 usec Cycle 12 2.2 SS pin pull up current mV uA V 200 uA 5.8 V 22 KHz 117 130 143 KHz 35 40 45 KHz 30 30 45 45 240 55 55 usec usec KHz/V 130 140 150 ◦C 3.8 V Confidential -6- OB_DOC_DS_0300 OB2203 http://www.elecfans.com 电子发烧友 http://bbs.elecfans.com 电子技术论坛 Quasi-Resonant Flyback PWM Controller voltage at SS pin V_latch_release Ivdd(latch) VCC latch release voltage VCC current when latch off PFCVCC section Rdson On-resistance of PMOS switch T_PFC_GTS PFC go to standby debounce time T_PFC_ON PFC ON debounce time Gate Drive Output Output Low Level VOL Output High Level VOH VG_Clamp Output Clamp Voltage Level T_r Output Rising Time Output Falling Time T_f should be larger than 200uA 5.5 VCC=V_latch_release+1 V Io = 100 mA (sink) Io = 100 mA (source) VCC=20V CL = 1nf CL = 1nf 6 V 40 uA 10 20 30 Ω 100 125 140 ms 4 8 12 mS 1 V V V 7.5 15.5 16.5 50 20 ©On-Bright Electronics 6.5 17.5 nSec nSec Confidential -7- OB_DOC_DS_0300 http://www.elecfans.com 电子发烧友 http://bbs.elecfans.com 电子技术论坛 OB2203 Quasi-Resonant Flyback PWM Controller CHARACTERIZATION PLOTS ©On-Bright Electronics Confidential -8- OB_DOC_DS_0300 http://www.elecfans.com 电子发烧友 http://bbs.elecfans.com 电子技术论坛 OB2203 Quasi-Resonant Flyback PWM Controller OPERATION DESCRIPTION Quasi-Resonant (QR) converter typically features lower EMI and higher power conversion efficiency compared to conventional hard-switched converter with a fixed switching frequency. OB2203 is a highly integrated QR controller optimized for offline flyback converter applications. The built-in advanced energy saving with high level protection features provide cost effective solutions for energy efficient power supplies. z Startup Current and Start up Control Startup current of OB2203 is designed to be very low so that VCC could be charged up above UVLO(exit) threshold level and device starts up quickly. A large value startup resistor can therefore be used to minimize the power loss yet reliable startup in application. For a typical AC/DC adaptor with universal input range design, a 2 MΩ, 1/8 W startup resistor could be used together with a VCC capacitor to provide a fast startup and yet low power dissipation design solution. z Operating Current The operating current of OB2203 is as low as 2.3mA. Good efficiency is achieved by the low operating current together with extended burst mode control schemes at No/light conditions. the frequency according to the load conditions. Generally, in flyback converter, the decreasing of loading results in voltage level decreasing at FB pin. The controller monitors the voltage level at FB and control the switching frequency. However, the valley switching characteristic is still preserved in PFM mode. That is, when loading decreases, the system automatically skip more and more valleys and the switching frequency is thus reduced. In such way, a smooth frequency foldback is realized and high power conversion efficiency is achieved. ■ At zero load or very light load conditions (VFB<Vth1), the system operates in On-Bright’s proprietary “extended burst mode”. In this condition, voltage at FB is below burst mode threshold level, Vth1. The Gate drive output switches only when VCC voltage drops below a preset level or FB input is active to output an on state. Otherwise the gate drive remains at off state to minimize the switching loss thus reduce the standby power consumption to the greatest extend. In extended burst mode, the switching frequency is fixed to 22KHz, in this way, possible audio noise is eliminated. z Multi-Mode Operation for High Efficiency OB2203 is a multi-mode QR controller. The controller changes the mode of operation according to FB voltage, which reflects the line and load conditions. ■ Under normal operating conditions (FB>Vth2, Figure 1), the system operates in QR mode. The frequency variation in QR mode is limited to the range of 40KHz ~ 130KHz due to the fact that frequency varies depending on the line voltage and the load conditions. Therefore, the system may actually work in DCM when 130KHz frequency clamping is reached. In contrast, the system may actually work in CCM when 40KHz frequency clamping is reached. System design should be optimized such that the operation frequency is within the range specified at full loading conditions and in universal AC line input range. ■ At light load condition (Vth1<VFB<Vth2, Figure 1), the system operates in PFM (pulse frequency modulation) mode for high power conversion efficiency. In PFM mode, the “ON” time in a switching cycle is fixed and the system modulates Figure 1 z Demagnetization Detection The core reset is detected by monitoring the voltage activity on the auxiliary windings through DEM pin. This voltage features a flyback polarity. A new cycle starts when the power switch is activated. After the on time (determined by the CS voltage and FB), the switch is off and the flyback stroke starts. After the flyback stroke, the drain voltage shows an oscillation with a frequency of approximately 1 / 2π L p C d , where L p is the ©On-Bright Electronics Confidential -9- OB_DOC_DS_0300 http://www.elecfans.com 电子发烧友 http://bbs.elecfans.com 电子技术论坛 OB2203 Quasi-Resonant Flyback PWM Controller primary self inductance of the transformer and Cd is the capacitance on the drain node. Figure 2 The typical detection level is fixed at 75mV at the DEM pin. Demagnetization is recognized by detection of a possible “valley” when the voltage at DEM is below 75mV in falling edge. DEM detection is suppressed during the first Tsupp time (typical value of 2us). This suppression is necessary in applications where the transformer has a large leakage inductance and at low output voltages or start-up. z Current Sensing and Leading Edge Blanking Cycle-by-Cycle current limiting is offered in OB2203 current mode control. The switch current is detected by a sense resistor into the CS pin. An internal leading edge blanking circuit chops off the sense voltage spike at initial MOSFET on state due to snubber diode reverse recovery so that the external RC filtering on sense input is no longer needed. The current limit comparator is disabled and cannot turn off the external MOSFET during the blanking period. The PWM duty cycle is determined by the current sense input voltage and the FB input voltage. z Adaptive Slope Compensation at Large Load The slop compensation to ensure system stable operation is active only at large load condition. At large load conditions (such as startup), the switching frequency can be low clamped to 40KHz and the system will actually work in CCM mode. To prevent the possible unstable operation and the sub-harmonic oscillation, an internal synchronized slope compensation is added to the current loop. The internal synchronized slope compensation is disabled at normal or light load, in such condition, the system will work in either QR or DCM mode. z Maximum and Minimum On-Time The minimum on-time of the system is determined by the LEB time (typical 350ns). The IC limits the on-time to a maximum time of 45us. z Ringing Suppression Timer A ringing suppression timer is implemented. In normal operation, the ringing suppression timer starts when CS reaches the feedback voltage FB, the gate drive GATE is set to low. During the ringing suppression time, gate drive GATE remains in low state and cannot turn power switch on gain. The ringing suppression is necessary in applications where the transformer has a large leakage inductance, particularly at low output voltages or startup. In OB2203, the ringing suppression timer is set to 2us internally. z PFC VCC power on/off control In medium to large power applications, PFC preconverter is required and PFC controller is powered by PWM auxiliary power supply. PFCVCC pin is directly connected to VCC pin by an internal low impedance power switching, thus no external components are needed. PFCVCC is shut down in any of the following conditions: any fault condition, No load/light load condition, soft start sequence and VCC voltage less than 12V. z Maximum and Minimum Frequency Clamp in QR operation According to the QR operation principle, the switching frequency is inversely proportional to the output power. Therefore, when the output power decreases, the switching frequency can become rather high without limiting. To meet the CISPR-22 EMI limit starting at 150KHz, the maximum switching frequency in OB2203 is internally limited to 130KHz. In addition to up clamping, the switching frequency is also low clamped to 40KHz in QR mode. z On chip Thermal shutdown OB2203 provides an on chip thermal shutdown. The IC will stop switching when the junction temperature exceeds the thermal shutdown temperature, typically 140 °C. The IC resumes normal operation when the junction temperature decreased by 20 °C z External latch trip point By externally forcing a level on pin SS (e.g.., with a signal coming from a temperature sensor) greater than 3.8V, OB2203 can be permanently latched-off. To resume normal operation, VCC voltage should ©On-Bright Electronics Confidential - 10 - OB_DOC_DS_0300 OB2203 http://www.elecfans.com 电子发烧友 http://bbs.elecfans.com 电子技术论坛 Quasi-Resonant Flyback PWM Controller go below 6V, which implies to unplug the SMPS form the mains. z OCP compensation for CCM/DCM A proprietary OCP compensation is provided for better OCP performance in the universal input range. Comparing to conventional OCP compensation where the gate delay is compensated, more sophisticated compensation is provided to also compensate the OCP at different line voltage since the switching frequency varies with line voltage. In this way, a more accurate OCP is achieved. z Over voltage protection (OVP) An over voltage protection (OVP) is implemented by sensing the auxiliary winding voltage at DEM pin during the flyback phase. The auxiliary winding voltage is a well-defined replica of the output voltage. The OVP works by sampling the plateau voltage at DEM pin during the flyback phase. A 2 us internal delay (plateau sampling) guarantees a clean plateau, provided that the leakage inductance ringing has been fully damped. When over load (for example, short circuit) occurs, the feedback current is below minimum value and a fault is detected. If this fault is present for more than 80ms, the controller enters an auto-recovery soft burst mode. All pulses are stopped, VCC will drops below UVLO and the controller will try to restart with the power on soft start. The SMPS enters the burst sequence and it resumes operation once the fault disappears. z Programmable Soft Start OB2203 features a programmable soft start to soften the constraints in the power supply during the startup. It is activated during the power on sequence. As soon as VCC reaches UVLO(OFF), an internal trimmed 10 uA current is sourced from SS pin and charges the external programming capacitor, the peak current is then gradually increased from zero. When SS pin reaches 2.2V, soft start process is over. UVLO(OFF) VCC 2.2V Auxiliary winding OB2203 R1 SS Plateau Sampling 6 R2 DEM Soft start process Lasts for 4 subsequent cycles ? Yes True OVP Figure 3 If the sampled plateau voltage exceeds the OVP trip level (3.75V), an internal counter starts counting subsequent OVP events. If OVP events are detected in successive 4 cycles, the controller assumes a true OVP and it enters a latch off mode and stops all switching operations. The counter has been added to prevent incorrect OVP detection which might occur during ESD or lightning events. If the output voltage exceeds the OVP trip level less than 4 successive cycles, the internal counter will be cleared and no fault is asserted. z Time 3.75V Figure 4 During the soft start process, there is a low frequency (40KHz) clamping to avoid the system switching frequency going too low. Every restart attempt is followed by soft start sequence. z Gate Drive The Gate pin is connected to the gate of an external MOSFET for power switch control. Too weak the gate drive results in higher conduction and switch loss of MOSFET while too strong gate drive output compromises the EMI. Good tradeoff is achieved through the built-in totem pole gate drive design with right output strength and dead time control. The low idle loss and good EMI system design is easier to achieve with this dedicated control scheme. An internal 15V clamp is added for MOSFET gate protection at high VCC voltage. Overload Operation ©On-Bright Electronics Confidential - 11 - OB_DOC_DS_0300 http://www.elecfans.com 电子发烧友 http://bbs.elecfans.com 电子技术论坛 OB2203 Quasi-Resonant Flyback PWM Controller PACKAGE MECHANICAL DATA 8-Pin Plastic DIP Symbol A A1 A2 B B1 C D E E1 e L E2 Dimensions In Millimeters Min Max 3.710 4.310 0.500 3.200 3.600 0.350 0.650 1.524 (BSC) 0.200 0.360 9.000 9.500 6.200 6.600 7.320 7.920 2.540 (BSC) 3.000 3.600 8.200 9.000 ©On-Bright Electronics Dimensions In Inches Min Max 0.146 0.170 0.020 0.126 0.142 0.014 0.026 0.060 (BSC) 0.008 0.014 0.354 0.374 0.244 0.260 0.288 0.312 0.100 (BSC) 0.118 0.142 0.323 0.354 Confidential - 12 - OB_DOC_DS_0300 http://www.elecfans.com 电子发烧友 http://bbs.elecfans.com 电子技术论坛 OB2203 Quasi-Resonant Flyback PWM Controller 8-Pin Plastic SOP Symbol A A1 A2 b c D E E1 e L θ Dimensions In Millimeters Min Max 1.750 1.350 0.250 0.100 1.550 1.300 0.330 0.510 0.170 0.250 5.150 4.700 4.000 3.800 6.200 5.800 1.270 (BSC) 1.270 0.400 8º 0º ©On-Bright Electronics Dimensions In Inches Min Max 0.053 0.069 0.004 0.010 0.051 0.061 0.013 0.020 0.006 0.010 0.185 0.203 0.150 0.157 0.228 0.244 0.050 (BSC) 0.016 0.050 0º 8º Confidential - 13 - OB_DOC_DS_0300