AD AD8567ACP

a
FEATURES
Single-Supply Operation: 4.5 V to 16 V
Input Capability Beyond the Rails
Rail-to-Rail Output Swing
Continuous Output Current: 35 mA
Peak Output Current: 250 mA
Offset Voltage: 10 mV
Slew Rate: 6 V/s
Unity Gain Stable with Large Capacitive Loads
Supply Current: 700 A per Amplifier
16 V Rail-to-Rail
Operational Amplifiers
AD8565/AD8566/AD8567
PIN CONFIGURATIONS
5-Lead SC70
(KS Suffix)
8-Lead MSOP
(RM Suffix)
AD8565
OUT 1
5 V–
OUT A
1
–IN A
V+ 2
+IN 3
4 –IN
APPLICATIONS
LCD Reference Drivers
Portable Electronics
Communications Equipment
AD8566
8
V+
2
7
OUT B
+IN A
3
6
–IN B
V–
4
5
+IN B
14-Lead TSSOP
(RU Suffix)
OUT A 1
14 OUT D
GENERAL DESCRIPTION
13 –IN D
+IN A 3
12 +IN D
V+ 4
11 V–
AD8567
+IN B 5
10 +IN C
–IN B 6
9 –IN C
OUT B 7
8
The AD8565, AD8566, and AD8567 are specified over the –40°C
to +85°C temperature range. The AD8565 single is available in a
5-lead SC70 package. The AD8566 dual is available in an 8-lead
MSOP package. The AD8567 quad is available in a 14-lead
TSSOP package and a 16-lead lead frame Chip Scale Package.
OUT C
NC
OUT A
OUT D
NC
16-Lead CSP
(CP Suffix)
16
15
14
13
–IN A
1
12
–IN D
+IN A
2
AD8567
11
+IN D
V+
3
TOP VIEW
10
V–
+IN B
4
5
6
7
8
OUT C
–IN C
9
–IN B
These LCD op amps have high slew rates, 35 mA continuous
output drive, 250 mA peak output drive, and high capacitive load
drive capability. They have wide supply range and offset voltages
below 10 mV. The AD8565, AD8566, and AD8567 are ideal for
LCD grayscale reference buffer and VCOM applications.
–IN A 2
OUT B
The AD8565, AD8566, and AD8567 are low-cost single supply
rail-to-rail input and output operational amplifiers optimized for
LCD monitor applications. They are built on an advanced highvoltage CBCMOS process. The AD8565 contains a single
amplifier, the AD8566 has two amplifiers, and the AD8567 has
four amplifiers.
+IN C
NC = NO CONNECT
REV. A
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
that may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 2001
AD8565/AD8566/AD8567–SPECIFICATIONS
Electrical Characteristics (4.5 V ≤ V ≤ 16 V, V
S
CM
= VS /2, TA = 25C, unless otherwise noted.)
Parameter
Symbol
Conditions
INPUT CHARACTERISTICS
Offset Voltage
Offset Voltage Drift
Input Bias Current
VOS
∆VOS/∆T
IB
–40°C ≤ TA ≤ +85°C
Input Offset Current
IOS
Input Voltage Range
Common-Mode Rejection Ratio
CMRR
Large Signal Voltage Gain
AVO
Input Impedance
Input Capacitance
ZIN
CIN
OUTPUT CHARACTERISTICS
Output Voltage High
Output Voltage Low
Continuous Output Current
Peak Output Current
POWER SUPPLY
Supply Voltage
Power Supply Rejection Ratio
Supply Current/Amplifier
DYNAMIC PERFORMANCE
Slew Rate
Gain Bandwidth Product
–3 dB Bandwidth
Phase Margin
Channel Separation
NOISE PERFORMANCE
Voltage Noise Density
Current Noise Density
VOH
VOL
IOUT
IPK
VS
PSRR
ISY
Min
Typ
Max
Unit
2
5
80
10
mV
µV/°C
nA
nA
nA
nA
V
–40°C ≤ TA ≤ +85°C
1
–40°C ≤ TA ≤ +85°C
Common-Mode Input
VCM = 0 to VS,
–40°C ≤ TA ≤ +85°C
RL = 10 kΩ,
VO = 0.5 to (VS – 0.5 V)
IL = 100 µA
VS = 16 V, IL = 5 mA
–40°C ≤ TA ≤ +85°C
VS = 4.5 V, IL = 5 mA
–40°C ≤ TA ≤ +85°C
IL = 100 µA
VS = 16 V, IL = 5 mA
–40°C ≤ TA ≤ +85°C
VS = 4.5 V, IL = 5 mA
–40°C ≤ TA ≤ +85°C
–0.5
54
95
dB
3
10
400
1
V/mV
kΩ
pF
VS – 0.005
15.95
V
V
V
V
V
mV
mV
mV
mV
mV
mA
mA
15.85
15.75
4.2
4.1
4.38
5
42
95
4.5
SR
GBP
BW
Øo
RL = 10 kΩ, CL = 200 pF
RL = 10 kΩ, CL = 10 pF
RL = 10 kΩ, CL = 10 pF
RL = 10 kΩ, CL = 10 pF
en
en
in
f = 1 kHz
f = 10 kHz
f = 10 kHz
150
250
300
400
35
250
VS = 16 V
VS = 4 V to 17 V,
–40°C ≤ TA ≤ +85°C
VO = VS/2, No Load
–40°C ≤ TA ≤ +85°C
600
800
80
130
VS + 0.5
70
4
90
700
16
V
850
1
dB
µA
mA
6
5
6
65
75
V/µs
MHz
MHz
Degrees
dB
26
25
0.8
nV/√Hz
nV/√Hz
pA/√Hz
Specifications subject to change without notice.
–2–
REV. A
AD8565/AD8566/AD8567
ABSOLUTE MAXIMUM RATINGS *
Supply Voltage (VS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 V
Input Voltage . . . . . . . . . . . . . . . . . . . . . –0.5 V to VS + 0.5 V
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . VS
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Operating Temperature Range . . . . . . . . . . . –40°C to +85°C
Junction Temperature Range . . . . . . . . . . . . –65°C to +150°C
Lead Temperature Range (Soldering, 60 sec) . . . . . . . . 300°C
*Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those listed in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
Package Type
JA1
JC
Unit
5-Lead SC70 (KS)
8-Lead MSOP (RM)
14-Lead TSSOP (RU)
16-Lead LFCSP (CP)
376
210
180
382
126
45
35
302
°C/W
°C/W
°C/W
°C/W
NOTES
1
θJA is specified for worst-case conditions, i.e., θJA is specified for device soldered
onto a circuit board for surface mount packages.
2
DAP is soldered down to PCB.
ORDERING GUIDE
Model*
Temperature
Range
Package Description
Package
Option
Branding
Information
AD8565AKS
AD8566ARM
AD8567ARU
AD8567ACP
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
5-Lead Plastic Surface-Mount
8-Lead MINI_SOIC
14-Lead Thin Shrink SO
16-Terminal Leadless Frame Chip Scale
KS-5
RM-8
RU-14
CP-16
ASA
ATA
*
Available in reels only.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the AD8565/AD8566/AD8567 features proprietary ESD protection circuitry, permanent damage
may occur on devices subjected to high-energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
REV. A
–3–
WARNING!
ESD SENSITIVE DEVICE
AD8565/AD8566/AD8567–Typical Performance Characteristics
0
1000
4.5V VS
TA = 25C
VOLTAGE NOISE DENSITY – nV Hz
0.25
0.50
VS = 16V
0.75
VS = 4.5V
1.00
1.25
1.50
40
25
TEMPERATURE – C
10
1
10
TPC 1. Input Offset Voltage vs. Temperature
10k
1.0
16V
SUPPLY CURRENT/AMPLIFIER – mA
4.5V VS
TA = 25C
CURRENT NOISE DENSITY – pA Hz
100
1k
FREQUENCY – Hz
TPC 4. Voltage Noise Density vs. Frequency
10
1
0.1
16V
100
85
10
100
1k
FREQUENCY – Hz
TPC 2. Current Noise Density vs. Frequency
VO = VS/2
AV = +1
TA = 25C
0.8
0.6
0.4
0.2
0
10k
0
4
2
6
8
10
12
SUPPLY VOLTAGE – V
14
16
18
TPC 5. Supply Current/Amplifier vs. Supply Voltage
0.80
VS = 16V
RL = 10k
CL = 100pF
AV = +1
TA = 25C
SUPPLY CURRENT/AMPLIFIER – mA
VCM = VS/2
TIME – 50mV/DIV
INPUT OFFSET VOLTAGE – mV
VCM = VS/2
0.75
VS = 16V
0.70
0.65
0.60
VS = 4.5V
0.55
0.50
FREQUENCY – 1s/DIV
TPC 3. Small Signal Transient Response
40
25
TEMPERATURE – C
85
TPC 6. Supply Current/Amplifier vs. Temperature
–4–
REV. A
AD8565/AD8566/AD8567
100
80
80
60
GAIN – dB
OVERSHOOT – %
70
VS = 16V
RL = 10k
CL = 40pF
TA = 25C
100
–OS
50
+OS
40
0
45
60
90
40
135
20
180
0
225
30
PHASE SHIFT – C
VS = 16V
VIN = 100mV p-p
RL = 10k
AV = +1
TA = 25C
90
270
20
10
0
10
100
LOAD CAPACITANCE – pF
1k
1k
TPC 7. Small Signal Overshoot vs. Load Capacitance
10M
100M
1k
TA = 25C
16
OUTPUT VOLTAGE – mV
14
OUTPUT SWING – V p-p
100k
1M
FREQUENCY – Hz
TPC 10. Open-Loop Gain and Phase Shift vs. Frequency
18
12
10
8
6
VS = 16V
AV = +1
RL = 10k
DISTORTION < 1%
TA = 25C
4
2
0
10k
10
100
1k
10k
100k
FREQUENCY – Hz
1M
100
VS = 16V
10
1
0.1
0.001
10M
TPC 8. Closed-Loop Output Swing vs. Frequency
VS = 4.5V
0.01
0.1
1
LOAD CURRENT – mA
10
100
TPC 11. Output Voltage to Supply Rail vs. Load Current
150
4.5V VS 16V
RL = 10k
CL = 40pF
TA = 25C
60
AVCL = –100
40
30
AVCL = –10
20
10
AVCL = +1
0
ISINK = 5mA
120
OUTPUT VOLTAGE – mV
CLOSED-LOOP GAIN – dB
50
135
105
VS = 4.5V
90
75
60
45
VS = 16V
30
15
0
10
100
1k
100k
10k
FREQUENCY – Hz
1M
10M
TPC 9. Closed-Loop Gain vs. Frequency
REV. A
40
25
TEMPERATURE – C
85
TPC 12. Output Voltage Swing to Rail vs. Temperature
–5–
AD8565/AD8566/AD8567
150
160
ISOURCE = 5mA
135
POWER SUPPLY REJECTION – dB
OUTPUT VOLTAGE – mV
120
VS = +4.5V
105
90
75
60
VS = +16V
45
30
15
0
VS = +16V
TA = 25C
140
120
100
80
+PSRR
60
–PSRR
40
20
0
20
40
25
TEMPERATURE – C
40
100
85
TPC 13. Output Voltage Swing to Rail vs. Temperature
1k
10k
100k
FREQUENCY – Hz
1M
10M
TPC 16. Power Supply Rejection Ratio vs. Frequency
500
VS = 16V
RL = 10k
AV = +1
TA = 25C
TA = 25C
450
400
VOLTAGE – 3V/DIV
IMPEDANCE – 350
VS = 4.5V
300
250
200
150
100
50
VS = 16V
0
100
10k
100k
FREQUENCY – Hz
1k
1M
10M
TIME – 40s/DIV
TPC 14. Close-Loop Output Impedance vs. Frequency
TPC 17. No Phase Reversal
1.8k
VS = 16V
TA = 25C
140
120
QUANTITY – Amplifiers
1.4k
100
CMRR – dB
VS = 16V
TA = 25C
1.6k
80
60
40
20
1.2k
1.0k
800
600
400
0
200
10
100
1k
100k
10k
FREQUENCY – Hz
1M
0
10
10M
TPC 15. Common-Mode Rejection Ratio vs. Frequency
8
6
0
2
4
4
2
INPUT OFFSET VOLTAGE – mV
6
8
10
TPC 18. Input Offset Voltage Distribution
–6–
REV. A
AD8565/AD8566/AD8567
7
5
6
3
2
BANDWIDTH – MHz
INPUT OFFSET CURRENT – nA
4
VS = 4.5V
1
0
VS = 16V
–1
–2
5
4
3
2
VS = 16V
AV = +1
RL = x
TA = 25C
–3
1
–4
0
–5
–40
25
TEMPERATURE – C
85
TPC 19. Input Offset Current vs. Temperature
14
16
VS = 5V
AV = +1
RL = 10k
TA = 25C
VS = 16V
–100
BANDWIDTH – MHz
INPUT BIAS CURRENT – nA
6
8
10
12
COMMON-MODE VOLTAGE – V
5
VS = 4.5V
–150
–200
–250
4
3
2
1
–300
0
–350
–40
25
TEMPERATURE – C
85
TPC 20. Input Bias Current vs. Temperature
–40
–60
–80
–100
4.5V
–120
16V
–140
–160
100
1k
FREQUENCY – Hz
10k
0
1
2
3
COMMON-MODE VOLTAGE – V
4
5
TPC 23. Frequency vs. Common-Mode Voltage
(VS = 5.0 V)
–20
CROSSTALK – dB
4
6
–50
60k
TPC 21. Channel A vs. Channel B Crosstalk
REV. A
2
TPC 22. Frequency vs. Common-Mode Voltage (VS = 16 V)
0
–180
50
0
–7–
AD8565/AD8566/AD8567
The AD856x family is designed to drive large capacitive loads in
LCD applications. It has high output current drive, rail-to-rail
input/output operation and is powered from a single 16 V supply.
It is also intended for other applications where low distortion and
high output current drive are needed.
Figure 1 illustrates a simplified equivalent circuit for the AD856x.
The rail-to-rail bipolar input stage is composed of two PNP
differential pairs, Q4–Q5 and Q10–Q11, operating in series with
diode protection networks, D1–D2. Diode network D1–D2
serves as protection against large transients for Q4–Q5, to
accommodate rail-to-rail input swing. D5–D6 protect Q10–Q11
against zenering. In normal operation, Q10–Q11 are off and their
input stage is buffered from the operational amplifier inputs by
Q6–D3 and Q8–D4. Operation of the input stage is best understood
as a function of applied common-mode voltage: When the inputs
of the AD856x are biased midway between the supplies, the
differential signal path gain is controlled by resistive loads (Via R9,
R10) Q4–Q5. As the input common-mode level is reduced toward
the negative supply (VNEG or GND), the input transistor current
sources, I1 and I2, are forced into saturation, thereby forcing the
Q6–D3 and Q8–D4 networks into cutoff; However, Q4–Q5 remain
active, providing input stage gain. Inversely, when common-mode
input voltage is increased toward the positive supply, Q4–Q5 are
driven into cutoff, Q3 is driven into saturation, and Q4 becomes
active, providing bias to the Q10–Q11 differential pair. The point
at which Q10–Q11 differential pair becomes active is approximately
equal to (VPOS – 1 V).
VPOS
BIAS LINE
Q4
D1
D2
R3
R4
Q6
Q8
C1
V+
R5
D3
Q10
R6
C2
Q11
I2
D6
400
200
0
–200
–400
–600
–800
–1,000
0
2
4
6
8
10
12
INPUT COMMON-MODE VOLTAGE – V
14
16
Figure 2. AD856x Input Bias Current vs. Common-Mode
Voltage
This input current is not inherently damaging to the device as
long as it is limited to 5 mA or less. If a condition exists using
the AD856x where the input exceeds the supply more than 0.6 V,
a series external resistor should be added. The size of the resistor
can be calculated by using the maximum overvoltage divided by
5 mA. This resistance should be placed in series with either input
exposed to an overvoltage.
FOLDED
CASCADE
R9
600
As with any semiconductor device, whenever the input exceeds
either supply voltages, attention needs to be paid to the input
overvoltage characteristics. As an overvoltage occurs, the amplifier
could be damaged, depending on the voltage level and the magnitude
of the fault current. When the input voltage exceeds either supply
by more than 0.6 V, internal pn junctions will allow current to
flow from the input to the supplies.
D4
D5
I1
VS = 16V
TA = 25C
800
Input Overvoltage Protection
V–
Q5
Q4
1,000
In order to achieve rail-to-rail output performance, the AD856x
design uses a complementary common-source (or gmRL) output.
This configuration allows output voltages to approach the power
supply rails, particularly if the output transistors are allowed to
enter the triode region on extremes of signal swing which are
limited by VGS, the transistor sizes, and output load current.
Also, this type of output stage exhibits voltage gain in an open-loop
gain configuration. The amount of gain depends on the total
load resistance at the output of the AD856x.
R1
Q3
The benefit of this type of input stage is low bias current. The
input bias current is the sum of base currents of Q4–Q5 and
Q6–Q8 over the range from (VNEG + 1 V) to (VPOS – 1 V). Outside
of this range, input bias current is dominated by the sum of base
current of Q10–Q11 for input signals close to VNEG and of Q6–Q8
(Q10–Q11) for signal close to VPOS. From this type of design,
the input bias current of AD856x not only exhibits different
amplitude, but also exhibits different polarities. Figure 2 provides
the characteristics of the input bias current versus common-mode
voltage. It is important to keep in mind that the source impedances
driving the AD856x inputs are balanced for optimum dc and ac
performance.
INPUT BIAS CURRENT – nA
APPLICATIONS
Theory of Operation
R10
VNEG
Figure 1. AD856x Equivalent Input Circuit
–8–
REV. A
AD8565/AD8566/AD8567
Output Phase Reversal
THD + N
The AD856x family is immune to phase reversal. Although
the device’s output will not change phase, large currents due
to input overvoltage could damage the device. In applications
where the possibility of an input voltage exceeding the supply
voltage exists, overvoltage protection should be used as described
in the previous section.
The AD856x family features low total harmonic distortion. Figure
4 shows a graph of THD + N versus frequency. The Total Harmonic
Distortion plus Noise for the AD856x over the entire supply range
is below 0.008%. When the device is powered from a 16 V supply,
the THD + N stays below 0.003%. Figure 4 shows the AD8566
in a unity noninverting configuration.
Power Dissipation
10
The maximum allowable internal junction temperature of 150°C
limits the AD856x family Maximum Power Dissipation. As the
ambient temperature increases, the maximum power dissipated
by the AD856x family must decrease linearly to maintain the
maximum junction temperature. If this maximum junction
temperature is exceeded momentarily, the part will still operate
properly once the junction temperature is reduced below 150°C.
If the maximum junction temperature is exceeded for an extended
period of time, overheating could lead to permanent damage of
the device.
THD + N – %
1
0.1
VS = 8V
The maximum safe junction temperature, TJMAX, is 150°C. Using
the following formula, we can obtain the maximum power that
the AD856x family can safely dissipate as a function of temperature.
0.01
20
PDISS = TJMAX – TA/θJA
where:
PDISS = AD856x power dissipation
TJMAX = AD856x maximum allowable junction temp (150°C)
TA = Ambient Temperature of the circuit
θJA = AD856x package thermal resistance, junction-to-ambient
The power dissipated by the device can be calculated as;
where:
VS = supply voltage
VOUT = output voltage
ILOAD = output load current
1.25
MAXIMUM POWER DISSIPATION – W
14-LEAD SOIC
1.00
8-LEAD MSOP
Short Circuit Output Conditions
The AD856x family does not have internal short circuit protection
circuitry. As a precautionary measure, it is recommended not to
short the output directly to the positive power supply or to ground.
VS
35 mA
For a 5 V single supply operation, RX should have a minimum
value of 143 Ω.
LCD Panel Applications
The AD856x amplifier is designed for LCD panel applications
or applications where large capacitive load drive is required. It
can instantaneously source/sink greater than 250 mA of current.
At unity gain, it can drive 1 µF without compensation. This
makes the AD856x ideal for LCD VCOM driver applications.
5-LEAD SOT-23
0.25
65
85
Figure 3. Maximum Power Dissipation vs. Temperature
for 5-, 8-, and 14-Lead Packages
REV. A
30k
Figure 4. THD + N vs. Frequency Graph
0.50
5
25
45
AMBIENT TEMPERATURE – C
10k
To evaluate the performance of the AD856x family, a test circuit
was developed to simulate the VCOM Driver application for an
LCD panel.
14-LEAD TSSOP
–15
1k
FREQUENCY – Hz
RX ≥
Figure 3 shows the maximum power dissipation versus temperature.
To achieve proper operation, use the previous equation to calculate
PDISS for a specific package at any given temperature, or use the
chart below.
0
–35
100
It is not recommended to operate the AD856x with more than
35 mA of continuous output current. The output current can be
limited by placing a series resistor at the output of the amplifier
whose value can be derive using the following equation:
PDISS = (VS – VOUT) ⫻ ILOAD
0.75
VS = 2.5V
–9–
AD8565/AD8566/AD8567
Figure 5 shows the test circuit. Series capacitors and resistors
connected to the output of the op amp represent the load of the
LCD panel. The 300 Ω and 3 kΩ feedback resistors are used to
improve settling time. This test circuit simulates the worst-case
scenario for a VCOM. It drives a represented load that is connected
to a signal switched symmetrically around VCOM. Figure 6 displays
a scope photo of the instantaneous output peak current capability
of the AD856x family.
100
90
CH 2 =
100mA/DIV
CH 1 = 5V/DIV
10
0%
300
8V
INPUT 0V TO 8V
SQUARE WAVE WITH
15.6s PULSEWIDTH
TIME – 2s/DIV
3k
10
10
10
Figure 6. Scope Photo of the VCOM Instantaneous
Peak Current
10
4V
MEASURE
CURRENT
10nF
10nF
10nF
10nF
10–20
Figure 5. VCOM Test Circuit with Supply Voltage at 16 V
–10–
REV. A
AD8565/AD8566/AD8567
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
5-Lead Plastic Surface-Mount
(KS-5)
8-Lead MINI_SOIC
(RM-8)
0.087 (2.20)
0.071 (1.80)
0.053 (1.35)
0.045 (1.15)
5
4
2
1
3
0.122 (3.10)
0.114 (2.90)
8
0.094 (2.40)
0.071 (1.80)
5
0.122 (3.10)
0.114 (2.90)
0.199 (5.05)
0.187 (4.75)
1
PIN 1
0.016 (0.40)
0.004 (0.10)
0.026 (0.65) BSC
0.039 (1.00)
0.031 (0.80)
0.004 (0.10)
0.000 (0.00)
PIN 1
0.0256 (0.65) BSC
0.043 (1.10)
0.031 (0.80)
0.012 (0.30) SEATING
0.006 (0.15) PLANE
4
0.120 (3.05)
0.112 (2.84)
0.120 (3.05)
0.112 (2.84)
0.043 (1.09)
0.037 (0.94)
0.006 (0.15)
0.002 (0.05)
0.012 (0.30)
0.004 (0.10)
0.007 (0.18)
0.004 (0.10)
0.018 (0.46)
SEATING 0.008 (0.20)
PLANE
0.011 (0.28)
0.003 (0.08)
14-Lead Thin Shrink SO
(RU-14)
0.201 (5.10)
0.193 (4.90)
14
8
0.177 (4.50)
0.169 (4.30)
0.256 (6.50)
0.246 (6.25)
1
7
PIN 1
0.006 (0.15)
0.002 (0.05)
0.0433 (1.10)
MAX
0.0118 (0.30)
0.0075 (0.19)
0.0256
(0.65)
BSC
SEATING
PLANE
0.0079 (0.20)
0.0035 (0.090)
8
0
0.028 (0.70)
0.020 (0.50)
16-Terminal Leadless Frame Chip Scale
(CP-16)
0.024 (0.60)
0.017 (0.42)
0.009 (0.24)
0.024 (0.60)
0.017 (0.42)
13
0.009 (0.24)
12
0.157 (4.0)
BSC SQ
PIN 1
INDICATOR
TOP
VIEW
12 MAX
0.148 (3.75)
BSC SQ
0.031 (0.80) MAX
0.026 (0.65) NOM
0.039 (1.00) MAX
0.033 (0.85) NOM
SEATING
PLANE
0.014 (0.35) 0.008 (0.20)
REF
0.011 (0.28)
0.009 (0.23)
0.026 (0.65)
BSC
0.030 (0.75)
0.024 (0.60)
0.020 (0.50)
0.073 (1.85)
0.067 (1.70) SQ
0.061 (1.55)
4
8
5
0.077 (1.95)
BSC
0.002 (0.05)
0.0004 (0.01)
0.0 (0.0)
–11–
1
9
CONTROLLING DIMENSIONS ARE IN MILLIMETERS
REV. A
16
BOTTOM
VIEW
33
27
0.028 (0.71)
0.016 (0.41)
AD8565/AD8566/AD8567
Revision History
Location
Page
Data Sheet changed from REV. 0 to REV. A.
PRINTED IN U.S.A.
Edit to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
C01909–.8–10/01(A)
Edit to 16-Lead CSP and 5-Lead SC70 Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
–12–
REV. A