AD ADF4211BRU

a
Dual RF/IF PLL Frequency Synthesizers
ADF4210/ADF4211/ADF4212/ADF4213
GENERAL DESCRIPTION
FEATURES
ADF4210: 550 MHz/1.2 GHz
ADF4211: 550 MHz/2.0 GHz
ADF4212: 1.0 GHz/2.7 GHz
ADF4213: 1.0 GHz/3 GHz
2.7 V to 5.5 V Power Supply
Separate Charge Pump Supply (VP) Allows Extended
Tuning Voltage in 3 V Systems
Programmable Dual Modulus Prescaler
RF and IF: 8/9, 16/17, 32/33, 64/65
Programmable Charge Pump Currents
3-Wire Serial Interface
Analog and Digital Lock Detect
Fastlock Mode
Power-Down Mode
The ADF4210/ADF4211/ADF4212/ADF4213 is a dual frequency
synthesizer that can be used to implement local oscillators (LO)
in the upconversion and downconversion sections of wireless
receivers and transmitters. They can provide the LO for both
the RF and IF sections. They consist of a low-noise digital PFD
(Phase Frequency Detector), a precision charge pump, a programmable reference divider, programmable A and B Counters
and a dual-modulus prescaler (P/P + 1). The A (6-bit) and B
(12-bit) counters, in conjunction with the dual modulus prescaler
(P/P + 1), implement an N divider (N = BP + A). In addition,
the 14-bit reference counter (R Counter), allows selectable
REFIN frequencies at the PFD input. A complete PLL (PhaseLocked Loop) can be implemented if the synthesizer is used with
an external loop filter and VCO (Voltage Controlled Oscillators).
Control of all the on-chip registers is via a simple 3-wire interface.
APPLICATIONS
The devices operate with a power supply ranging from 2.7 V to
Base Stations for Wireless Radio (GSM, PCS, DCS,
5 V and can be powered down when not in use.
CDMA, WCDMA)
Wireless Handsets (GSM, PCS, DCS, CDMA, WCDMA)
Wireless LANS
Communications Test Equipment
CATV Equipment
FUNCTIONAL BLOCK DIAGRAM
VDD1
VDD2
VP1
VP2
RSET
12-BIT IF
B-COUNTER
IFIN
REFERENCE
PHASE
COMPARATOR
IF
PRESCALER
CHARGE
PUMP
8-BIT IF
A-COUNTER
REFIN
IF
LOCK
DETECT
OSCILLATOR
CPIF
IF CURRENT
SETTING
IFCP3 IFCP2 IFCP1
14-BIT IF
R-COUNTER
CLOCK
DATA
OUTPUT
MUX
24-BIT
DATA
SDOUT
REGISTER
MUXOUT
LE
RFCP3 RFCP2 RFCP1
14-BIT RF
R-COUNTER
RF
LOCK
DETECT
12-BIT RF
B-COUNTER
RFIN
CHARGE
PUMP
RF
PRESCALER
PHASE
COMPARATOR
6-BIT RF
A-COUNTER
DGNDRF
AGNDRF
DGNDIF
DGNDIF
IF CURRENT
SETTING
ADF4210/ADF4211/
ADF4212/ADF4213
CPRF
REFERENCE
RSET
FLO SWITCH
FLO
AGNDIF
REV. A
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties that
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 2001
ADF4210/ADF4211/ADF4212/ADF4213–SPECIFICATIONS1
(VDD1 = VDD2 = 3 V 10%, 5 V 10%; VDD1, VDD2 ≤ VP1, VP2 ≤ 6.0 V ; AGNDRF = DGNDRF = AGNDIF = DGNDIF = 0 V; RSET = 2.7 k dBm to 50 ;
TA = TMIN to TMAX unless otherwise noted.)
B Version
B Chips2
Unit
0.1/1.2
0.1/2.0
0.15/2.7
0.2/3.0
–10/0
0.1/1.2
0.1/2.0
0.15/2.7
0.2/3.0
–10/0
GHz min/max
GHz min/max
GHz min/max
GHz min/max
dBm min/max
60/550
60/550
0.06/1.0
0.06/1.0
–10/0
60/550
60/550
0.06/1.0
0.06/1.0
–10/0
MHz min/max
MHz min/max
GHz min/max
GHz min/max
dBm min/max
165
165
MHz max
0.18/1.2
0.18/2.0
0.2/2.3
0.2/2.5
–5/0
0.18/1.2
0.18/2.0
0.2/2.3
0.2/2.5
–5/0
GHz min/max
GHz min/max
GHz min/max
GHz min/max
dBm min/max
100/550
100/550
0.1/1.0
0.1/1.0
–5/0
100/550
100/550
0.1/1.0
0.1/1.0
–5/0
MHz min/max
MHz min/max
GHz min/max
GHz min/max
dBm min/max
200
200
MHz max
REFIN CHARACTERISTICS
REFIN Input Frequency
0/115
0/115
MHz min/max
REFIN Input Sensitivity4
–5/0
–5/0
dBm min/max
REFIN Input Capacitance
REFIN Input Current
10
± 100
10
± 100
pF max
µA max
PHASE DETECTOR
Phase Detector Frequency5
55
55
MHz max
CHARGE PUMP
ICP Sink/Source
High Value
Low Value
Absolute Accuracy
RSET Range
ICP Three-State Leakage Current
Sink and Source Current Matching
ICP vs. VCP
ICP vs. Temperature
5
625
3
1.5/5.6
1
2
2
2
5
625
3
1.5/5.6
1
2
2
2
mA typ
µA typ
% typ
kΩ, min/max
nA typ
% typ
% typ
% typ
LOGIC INPUTS
VINH, Input High Voltage
VINL, Input Low Voltage
IINH/IINL, Input Current
CIN, Input Capacitance
0.8 × DVDD
0.2 × DVDD
±1
10
0.8 × DVDD
0.2 × DVDD
±1
10
V min
V max
µA max
pF max
LOGIC OUTPUTS
VOH, Output High Voltage
VOL, Output Low Voltage
DVDD – 0.4
0.4
DVDD – 0.4
0.4
V min
V max
Parameter
RF/IF CHARACTERISTICS (3 V)
RF Input Frequency (RFIN)
ADF4210
ADF4211
ADF4212
ADF4213
RF Input Sensitivity
IF Input Frequency (IFIN)
ADF4210
ADF4211
ADF4212
ADF4213
IF Input Sensitivity
Maximum Allowable
Prescaler Output Frequency3
RF/IF CHARACTERISTICS (5 V)
RF Input Frequency (RFIN)
ADF4210
ADF4211
ADF4212
ADF4213
RF Input Sensitivity
IF Input Frequency (IFIN)
ADF4210
ADF4211
ADF4212
ADF4213
IF Input Sensitivity
Maximum Allowable
Prescaler Output Frequency3
–2–
Test Conditions/Comments
See Figure 3 for Input Circuit.
Use a square wave for frequencies lower than FMIN.
See Figure 3 for Input Circuit.
Use a square wave for frequencies lower than FMIN.
See Figure 2 for Input Circuit.
For F < 5 MHz, use dc-coupled square wave
(0 to VDD ).
AC-Coupled. When dc-coupled, 0 to VDD max
(CMOS-Compatible)
Programmable: See Table V
With RSET = 2.7 kΩ
With RSET = 2.7 kΩ
0.5 V ⱕ VCP ⱕ VP – 0.5 V
0.5 V ⱕ VCP ⱕ VP – 0.5 V
VCP = VP /2
IOH = 500 µA
IOL = 500 µA
REV. A
ADF4210/ADF4211/ADF4212/ADF4213
Parameter
POWER SUPPLIES
VDD1
VDD2
VP
IDD (RF + IF)6
ADF4210
ADF4211
ADF4212
ADF4213
IDD (RF Only)
ADF4210
ADF4211
ADF4212
ADF4213
IDD (IF Only)
ADF4210
ADF4211
ADF4212
ADF4213
IP (IP1 + IP2)
Low-Power Sleep Mode
NOISE CHARACTERISTICS
ADF4213 Phase Noise Floor7
Phase Noise Performance8
ADF4210/ADF4211, IF: 540 MHz Output9
ADF4212/ADF4213, IF: 900 MHz Output10
ADF4210/ADF4211, RF: 900 MHz Output10
ADF4212/ADF4213, RF: 900 MHz Output10
ADF4211/ADF4212, RF: 1750 MHz Output12
ADF4211/ADF4212, RF: 1750 MHz Output13
ADF4212/ADF4213, RF: 2400 MHz Output14
Spurious Signals
ADF4210/ADF4211, IF: 540 MHz Output9
ADF4212/ADF4213, IF: 900 MHz Output10
ADF4210/ADF4211, RF: 900 MHz Output10
ADF4212/ADF4213, RF: 900 MHz Output10
ADF4211/ADF4212, RF: 1750 MHz Output12
ADF4211/ADF4212, RF: 1750 MHz Output13
ADF4212/ADF4213, RF: 2400 MHz Output14
B Version B Chips2 Unit
Test Conditions/Comments
2.7/5.5
VDD1
VDD1/6.0
2.7/5.5
VDD1
VDD1/6.0
V min/V max
V min/V max
VDD1, VDD2 ⱕ VDD1, VDD2 ⱕ 6.0 V
11.5
15.0
17.5
20
11.5
15.0
17.5
20
mA max
mA max
mA max
mA max
9.0 mA typical
11.0 mA typical
13.0 mA typical
15 mA typical
6.75
10
12.5
15
6.75
10
12.5
15
mA max
mA max
mA max
mA max
5.0 mA typical
7.0 mA typical
9.0 mA typical
11 mA typical
5.5
5.5
5.5
5.5
1.0
1
5.5
5.5
5.5
5.5
1.0
1
mA max
mA max
mA max
mA max
mA max
µA typ
4.5 mA typical
4.5 mA typical
4.5 mA typical
4.5 mA typical
TA = 25°C, 0.55 mA typical
–171
–164
–171
–164
dBc/Hz typ
dBc/Hz typ
–91
–89
–89
–91
–85
–67
–88
–91
–89
–89
–91
–85
–67
–88
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
dBc/Hz typ
@ 25 kHz PFD Frequency
@ 200 kHz PFD Frequency
@ VCO Output
@ 1 kHz Offset and 200 kHz PFD Frequency
See Note 11
See Note 11
See Note 11
See Note 11
@ 200 Hz Offset and 10 kHz PFD Frequency
@ 1 kHz Offset and 1 MHz PFD Frequency
–88/–90
–90/–94
–90/–94
–90/–94
–80/–82
–65/–70
–80/–82
–88/–90
–90/–94
–90/–94
–90/–94
–80/–82
–65/–70
–80/–82
dB typ
dB typ
dB typ
dB typ
dB typ
dB typ
dB typ
@ 200 kHz/400 kHz and 200 kHz PFD Frequency
See Note 11
See Note 11
See Note 11
See Note 11
@ 10 kHz/20 kHz and 10 kHz PFD Frequency
@ 200 kHz/400 kHz and 200 kHz PFD Frequency
NOTES
1
Operating temperature range is as follows: B Version: –40°C to +85°C.
2
The B Chip specifications are given as typical values.
3
This is the maximum operating frequency of the CMOS counters. The prescaler value should be chosen to ensure that the IF/RF input is divided down to a frequency that is
less than this value.
4
VDD1 = VDD2 = 3 V; For VDD1 = VDD2 = 5 V, use CMOS-compatible levels, TA = 25°C.
5
Guaranteed by design. Sample tested to ensure compliance.
6
VDD = 3 V; P = 16; RFIN = 900 MHz; IFIN = 540 MHz, TA = 25°C.
7
The synthesizer phase noise floor is estimated by measuring the in-band phase noise at the output of the VCO and subtracting 20 logN (where N is the N divider value). See
TPC 16.
8
The phase noise is measured with the EVAL-ADF4210/ADF4212/ADF4213EB Evaluation Board and the HP8562E Spectrum Analyzer. The spectrum analyzer provides the
REFIN for the synthesizer (fREFOUT = 10 MHz @ 0 dBm).
9
fREFIN = 10 MHz; fPFD = 200 kHz; Offset frequency = 1 kHz; fIF = 540 MHz; N = 2700; Loop B/W = 20 kHz.
10
fREFIN = 10 MHz; fPFD = 200 kHz; Offset frequency = 1 kHz; fRF = 900 MHz; N = 4500; Loop B/W = 20 kHz.
11
Same conditions as listed in Note 10.
12
fREFIN = 10 MHz; fPFD = 200 kHz; Offset frequency = 1 kHz; fRF = 1750 MHz; N = 8750; Loop B/W = 20 kHz.
13
fREFIN = 10 MHz; fPFD = 10 kHz; Offset frequency = 200 Hz; fRF = 1750 MHz; N = 175000; Loop B/W = 1 kHz.
14
fREFIN = 10 MHz; fPFD = 1 MHz; Offset frequency = 1 kHz; fRF = 1960 MHz; N = 9800; Loop B/W = 20 kHz.
Specifications subject to change without notice.
REV. A
–3–
ADF4210/ADF4211/ADF4212/ADF4213
(V 1 = V 2 = 3 V 10%, 5 V 10%; V 1, V 2 ≤ V 1, V 2 ≤ 6 V 10%; AGND
TIMING CHARACTERISTICS = AGND = DGND = 0 V; T = T to T unless otherwise noted.)
DD
DD
IF
DD
IF
A
MIN
DD
P
P
RF
= DGNDRF
MAX
Parameter
Limit at
TMIN to TMAX
(B Version)
Unit
Test Conditions/Comments
t1
t2
t3
t4
t5
t6
10
10
25
25
10
20
ns min
ns min
ns min
ns min
ns min
ns min
DATA to CLOCK Set-Up Time
DATA to CLOCK Hold Time
CLOCK High Duration
CLOCK Low Duration
CLOCK to LE Set-Up Time
LE Pulsewidth
NOTES
Guaranteed by design but not production tested.
Specifications subject to change without notice.
t3
t4
CLOCK
t1
DATA
DB20
(MSB)
t2
DB19
DB2
DB1
(CONTROL BIT C2)
DB0 (LSB)
(CONTROL BIT C1)
t6
LE
t5
LE
Figure 1. Timing Diagram
ABSOLUTE MAXIMUM RATINGS 1, 2
CSP θJA (Paddle Not Soldered) . . . . . . . . . . . . . . . . 216°C/W
Lead Temperature, Soldering
Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . . 215°C
Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220°C
(TA = 25°C unless otherwise noted)
VDD1 to GND3 . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
VDD1 to VDD2 . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +0.3 V
VP1, VP2 to GND . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
VP1, VP2 to VDD1 . . . . . . . . . . . . . . . . . . . . –0.3 V to +5.5 V
Digital I/O Voltage to GND . . . . . . –0.3 V to DVDD + 0.3 V
Analog I/O Voltage to GND . . . . . . . . . –0.3 V to VP + 0.3 V
REFIN, RFINA, RFINB,
IFINA, IFINB to GND . . . . . . . . . . . . –0.3 V to VDD + 0.3 V
Operating Temperature Range
Industrial (B Version) . . . . . . . . . . . . . . . . –40°C to +85°C
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Maximum Junction Temperature . . . . . . . . . . . . . . . . 150°C
TSSOP θJA Thermal Impedance . . . . . . . . . . . . . 150.4°C/W
CSP θJA (Paddle Soldered) . . . . . . . . . . . . . . . . . . . 122°C/W
NOTES
1
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those listed in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
2
This device is a high-performance RF integrated circuit with an ESD rating of
< 2 kV and it is ESD sensitive. Proper precautions should be taken for handling
and assembly.
3
GND = AGND = DGND = 0 V.
TRANSISTOR COUNT
11749 (CMOS) and 522 (Bipolar).
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the ADF4210/ADF4211/ADF4212/ADF4213 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high-energy electrostatic discharges. Therefore,
proper ESD precautions are recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
ORDERING GUIDE
Model
Temperature Range
Package Description
Package Option*
ADF4210BRU
ADF4210BCP
ADF4211BRU
ADF4211BCP
ADF4212BRU
ADF4212BCP
ADF4213BRU
ADF4213BCP
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
Thin Shrink Small Outline Package (TSSOP)
Chip Scale Package
Thin Shrink Small Outline Package (TSSOP)
Chip Scale Package
Thin Shrink Small Outline Package (TSSOP)
Chip Scale Package
Thin Shrink Small Outline Package (TSSOP)
Chip Scale Package
RU-20
CP-20
RU-20
CP-20
RU-20
CP-20
RU-20
CP-20
*Contact the factory for chip availability.
–4–
REV. A
ADF4210/ADF4211/ADF4212/ADF4213
PIN FUNCTION DESCRIPTIONS
Pin Number
TSSOP
Mnemonic
Function
1
VDD1
2
V P1
3
CPRF
4
5
6
7
8
DGNDRF
RFIN
AGNDRF
FLO
REFIN
9
10
DGNDIF
MUXOUT
11
CLK
12
DATA
13
LE
14
RSET
15
16
17
18
AGNDIF
IFIN
DGNDIF
CPIF
19
V P2
20
VDD2
Power Supply for the RF Section. Decoupling capacitors to the ground plane should be placed as
close as possible to this pin. V DD1 should have a value of between 2.7 V and 5.5 V. V DD1 must have
the same potential as VDD2.
Power Supply for the RF Charge Pump. This should be greater than or equal to V DD1. In systems where
VDD1 is 3 V, it can be set to 6 V and used to drive a VCO with a tuning range up to 6 V.
Output from the RF Charge Pump. This is normally connected to a loop filter which drives the input
to an external VCO.
Ground Pin for the RF Digital Circuitry.
Input to the RF Prescaler. This low level input signal is ac-coupled from the RF VCO.
Ground Pin for the RF Analog Circuitry.
RF/IF Fastlock Mode.
Reference Input. This is a CMOS input with a nominal threshold of V DD/2 and an equivalent input
resistance of 100 kΩ. This input can be driven from a TTL or CMOS crystal oscillator.
Digital Ground for the IF Digital, Interface and Control Circuitry.
This multiplexer output allows either the IF/RF Lock Detect, the scaled RF, scaled IF or the scaled
Reference Frequency to be accessed externally.
Serial Clock Input. This serial clock is used to clock in the serial data to the registers. The data is
latched into the 24-bit shift register on the CLK rising edge. This input is a high impedance
CMOS input.
Serial Data Input. The serial data is loaded MSB first with the two LSBs being the control bits. This
input is a high impedance CMOS input.
Load Enable, CMOS Input. When LE goes high, the data stored in the shift registers is loaded into
one of the four latches, the latch being selected using the control bits.
Connecting a resistor between this pin and ground sets the maximum RF and IF charge pump output
current. The nominal voltage potential at the RSET pin is 0.66 V. The relationship between I CP and RSET is
13.5
ICP MAX =
RSET
So, with RSET = 2.7 kΩ, ICP MAX = 5 mA for both the RF and IF Charge Pumps.
Ground Pin for the IF Analog Circuitry.
Input to the RF Prescaler. This low-level input signal is ac-coupled from the IF VCO.
Ground Pin for the IF Digital, Interface, and Control Circuitry.
Output from the IF Charge Pump. This is normally connected to a loop filter which drives the input
to an external VCO.
Power Supply for the IF Charge Pump. This should be greater than or equal to V DD2. In systems where
VDD2 is 3 V, it can be set to 6 V and used to drive a VCO with a tuning range up to 6 V.
Power Supply for the IF, Digital and Interface Section. Decoupling capacitors to the ground plane should
be placed as close as possible to this pin. V DD2 should have a value of between 2.7 V and 5.5 V. VDD2
must have the same potential as V DD1.
PIN CONFIGURATIONS
DGNDIF
16
IFIN
REV. A
13
LE
12
DATA
MUXOUT 10
11
CLK
–5–
AGNDRF
4
FLO
5
16
VP2
ADF4210/
ADF4211/
ADF4212/
ADF4213
RFIN 3
TOP VIEW 15 AGNDIF
(Not to Scale)
14 RSET
FLO 7
REFIN 8
VDD2
CPRF 1
DGNDRF 2
AGNDRF 6
DGNDIF 9
18 17
15 DGNDIF
14 IFIN
13 AGNDIF
TOP VIEW
(Not to Scale)
6
7
8
9
10
DATA
CPIF
17
19
CLK
RFIN 5
18
20
MUXOUT
CPRF 3
DGNDRF 4
VP1
VP2
ADF4210/
ADF4211/
ADF4212/
ADF4213
VDD1
VDD2
19
REFIN
20
VP1 2
DGNDIF
VDD1 1
CPIF
CP-20
TSSOP
12 RSET
11 LE
ADF4210/ADF4211/ADF4212/ADF4213–Typical Performance Characteristics
0
FREQUENCY
S11 REAL
S11 IMAG
FREQUENCY
S11 REAL
S11 IMAG
50000000.0
150000000.0
250000000.0
350000000.0
450000000.0
550000000.0
650000000.0
750000000.0
850000000.0
950000000.0
1050000000.0
1150000000.0
1250000000.0
1350000000.0
1450000000.0
1550000000.0
1650000000.0
1750000000.0
1850000000.0
1950000000.0
2050000000.0
0.955683
0.956993
0.935463
0.919706
0.871631
0.838141
0.799005
0.749065
0.706770
0.671007
0.630673
0.584013
0.537311
0.505090
0.459446
0.381234
0.363150
0.330545
0.264232
0.242065
0.181238
–0.052267
–0.112191
–0.185212
–0.252576
–0.323799
–0.350455
–0.408344
–0.455840
–0.471011
–0.535268
–0.557699
–0.604256
–0.622297
–0.642019
–0.686409
–0.693908
–0.679602
–0.721812
–0.697386
–0.711716
–0.723232
2150000000.0
2250000000.0
2350000000.0
2450000000.0
2550000000.0
2650000000.0
2750000000.0
2850000000.0
2950000000.0
0.138086
0.102483
0.054916
0.018475
–0.019935
–0.054445
–0.083716
–0.129543
–0.154974
–0.699896
–0.704160
–0.696325
–0.669617
–0.668056
–0.666995
–0.634725
–0.615246
–0.610398
VDD = 3V
RF INPUT POWER – dBm
–5
VP = 3V
–10
TA = +85C
–15
TA = +25C
–20
TA = –40C
–25
–30
–35
1
0
2
3
RF INPUT FREQUENCY – GHz
TPC 4. Input Sensitivity (ADF4213)
TPC 1. S-Parameter Data for the ADF4213 RF Input
(Up to 3.0 GHz)
10dB/DIVISION
–40
0
OUTPUT POWER – dB
VDD = 3V, VP = 5V
–50
0.54 rms
–20
PFD FREQUENCY = 200kHz
–30
LOOP BANDWIDTH = 20kHz
–60
RES. BANDWIDTH = 10Hz
–40
VIDEO BANDWIDTH = 10Hz
–50
SWEEP = 1.9 SECONDS
AVERAGES = 19
–60
–70
–91.2dBc/Hz
–70
–80
–90
–100
–110
–80
–120
–90
–130
–140
100Hz
–100
–2kHz
–1kHz
900MHz
+1kHz
+2kHz
RL = –40dBc/Hz
RMS NOISE = 0.6522
0
–10
–50
0.65 rms
OUTPUT POWER – dB
PHASE NOISE – dBc/Hz
–60
–70
–80
–90
–100
–110
REFERENCE
LEVEL = –5.7dBm
VDD = 3V, VP = 5V
ICP = 5mA
–20
PFD FREQUENCY = 200kHz
–30
LOOP BANDWIDTH = 20kHz
RES. BANDWIDTH = 1kHz
–40
VIDEO BANDWIDTH = 1kHz
–50
SWEEP = 4.2 SECONDS
AVERAGES = 20
–60
–70
–91.0dBc/Hz
–80
–120
–90
–130
–140
100Hz
1MHz
1kHz
10kHz
100kHz
FREQUENCY OFFSET FROM 900MHz CARRIER
TPC 5. ADF4213 Integrated Phase Noise (900 MHz, 200 kHz,
20 kHz, Typical Lock Time: 400 µ s)
TPC 2. ADF4213 Phase Noise (900 MHz, 200 kHz, 20 kHz)
10dB/DIVISION
–40
RMS NOISE = 0.5421
ICP = 5mA
PHASE NOISE – dBc/Hz
REFERENCE
LEVEL = –5.2dBm
–10
RL = –40dBc/Hz
–100
1kHz
10kHz
100kHz
FREQUENCY OFFSET FROM 900MHz CARRIER
–400kHz
1MHz
TPC 3. ADF4213 Integrated Phase Noise (900 MHz,
200 kHz, 35 kHz, Typical Lock Time: 200 µ s)
–200kHz
900MHz
200kHz
400kHz
TPC 6. ADF4213 Reference Spurs (900 MHz, 200 kHz, 20 kHz)
–6–
REV. A
ADF4210/ADF4211/ADF4212/ADF4213
0
0
REFERENCE
LEVEL = –5.7dBm
–10
–20
VDD = 3V, VP = 5V
ICP = 5mA
–10
PFD FREQUENCY = 200kHz
–20
REFERENCE
LEVEL = –8.0dBm
OUTPUT POWER – dB
OUTPUT POWER – dB
LOOP BANDWIDTH = 3kHz
RES. BANDWIDTH = 1kHz
VIDEO BANDWIDTH = 1kHz
–40
SWEEP = 4.2 SECONDS
–50
ICP = 5mA
PFD FREQUENCY = 30kHz
LOOP BANDWIDTH = 35kHz
–30
VDD = 3V, VP = 5V
AVERAGES = 25
–60
–70
–30
RES. BANDWIDTH = 10kHz
VIDEO BANDWIDTH = 10kHz
–40
SWEEP = 477ms
–50
AVERAGES = 10
–60
–70
–90.5dBc/Hz
–80
–80
–90
–90
–100
–400kHz
–200kHz
900MHz
+200kHz
–100
+400kHz
–400Hz
TPC 7. ADF4213 Reference Spurs (900 MHz,
200 kHz, 35 kHz)
10dB/DIVISION
–40
RL = –40dBc/Hz
0
+400Hz
VDD = 3V, VP = 5V
ICP = 5mA
LOOP BANDWIDTH = 3kHz
POWER OUTPUT – dB
PHASE NOISE – dBc/Hz
+200Hz
PFD FREQUENCY = 30kHz
–20
1.6 rms
–80
–90
–100
–110
–120
–30
RES. BANDWIDTH = 3Hz
–40
VIDEO BANDWIDTH = 3Hz
SWEEP = 255 SECONDS
–50
POSITIVE PEAK DETECT
MODE
–60
–79.6dBc
–70
–80
–130
–90
FREQUENCY OFFSET FROM 1750MHz CARRIER
–100
1MHz
–80kHz
TPC 8. ADF4213 Integrated Phase Noise (1750 MHz,
30 kHz, 3 kHz)
0
REFERENCE
LEVEL = –4.2dBm
–10
–20
10dB/DIVISION
–40
VDD = 3V, VP = 5V
ICP = 5mA
–50
PFD FREQUENCY = 1MHz
–60
PHASE NOISE – dBc/Hz
–30
RES. BANDWIDTH = 10Hz
VIDEO BANDWIDTH = 10Hz
–40
SWEEP = 1.9 SECONDS
–50
AVERAGES = 45
–60
–86.6dBc/Hz
–70
TPC 9. ADF4213 Phase Noise (2800 MHz, 1 MHz, 100 kHz)
RMS NOISE = 1.7
1.7 rms
–110
–140
100Hz
+2kHz
RL = –40dBc/Hz
–100
–130
+1kHz
+80kHz
–90
–120
3100MHz
+40kHz
–80
–90
–1kHz
1750MHz
–70
–80
–2kHz
–40kHz
TPC 11. ADF4213 Reference Spurs (1750 MHz,
30 kHz, 3 kHz)
LOOP BANDWIDTH = 100kHz
OUTPUT POWER – dB
REFERENCE
LEVEL = –5.7dBm
–10
–70
REV. A
1750MHz
RMS NOISE = 1.6
–60
–100
–200Hz
TPC 10. ADF4213 Phase Noise (1750 MHz, 30 kHz, 3 kHz)
–50
–140
100Hz
–75.2dBc/Hz
FREQUENCY OFFSET FROM 3100MHz CARRIER
1MHz
TPC 12. ADF4213 Integrated Phase Noise (2800 MHz,
1 MHz, 100 kHz)
–7–
ADF4210/ADF4211/ADF4212/ADF4213
–120
0
REFERENCE
LEVEL = –17.2dBm
–10
VDD = 3V
VP = 5V
VDD = 3V, VP = 5V
ICP = 5mA
–130
PFD FREQUENCY = 1MHz
–20
RES. BANDWIDTH = 1kHz
–40
VIDEO BANDWIDTH = 1kHz
PHASE NOISE – dBc/Hz
OUTPUT POWER – dB
LOOP BANDWIDTH = 100kHz
–30
SWEEP = 13 SECONDS
–50
AVERAGES = 1
–60
–80.6dBc
–70
–80
–140
–150
–160
–170
–90
–180
–100
–2MHz
–1MHz
3100MHz
+1MHz
+2MHz
TPC 13. ADF4213 Reference Spurs (2800 MHz, 1 MHz,
100 kHz)
–60
FIRST REFERENCE SPUR – dBc
VDD = 3V
VP = 3V
PHASE NOISE – dBc/Hz
10000
TPC 16. ADF4213 Phase Noise (Referred to CP Output)
vs. PFD Frequency
–60
–70
–80
–90
–100
–40
0
–20
20
40
TEMPERATURE – C
60
80
VDD = 3V
VP = 5V
–70
–80
–90
–100
–40
100
TPC 14. ADF4213 Phase Noise vs. Temperature (900 MHz,
200 kHz, 20 kHz)
–20
0
20
40
TEMPERATURE – C
60
80
100
TPC 17. ADF4213 Reference Spurs vs. Temperature
(900 MHz, 200 kHz, 20 kHz)
–5
–60
–15
VDD = 3V
VP = 5V
–25
VDD = 3V
VP = 5V
PHASE NOISE – dBc/Hz
FIRST REFERENCE SPUR – dBc
10
100
1000
PHASE DETECTOR FREQUENCY – kHz
1
–35
–45
–55
–65
–75
–85
–70
–80
–90
–95
–105
0
1
2
3
TUNING VOLTAGE – Volts
4
–100
–40
5
TPC 15. ADF4213 Reference Spurs (200 kHz) vs. V TUNE
(900 MHz, 200 kHz, 20 kHz)
–20
0
20
40
TEMPERATURE – C
60
80
100
TPC 18. ADF4213 Phase Noise vs. Temperature
(836 MHz, 30 kHz, 3 kHz)
–8–
REV. A
ADF4210/ADF4211/ADF4212/ADF4213
PRESCALER (P/P + 1)
FIRST REFERENCE SPUR – dBc
–60
The dual modulus prescaler (P/P + 1), along with the A and
B counters, enables the large division ratio, N, to be realized
(N = PB + A). The dual-modulus prescaler, operating at CML
levels, takes the clock from the RF/IF input stage and divides
it down to a manageable frequency for the CMOS A and B
counters in the RF and If sections. The prescaler in both
sections is programmable. It can be set in software to 8/9, 16/17,
32/33, or 64/65. See Tables IV and VI. It is based on a synchronous 4/5 core.
VDD = 3V
VP = 5V
–70
–80
–90
RF/IF A AND B COUNTERS
–100
–40
0
–20
20
40
TEMPERATURE – C
60
80
100
TPC 19. ADF4213 Reference Spurs vs. Temperature
(836 MHz, 30 kHz, 3 kHz)
Pulse Swallow Function
CIRCUIT DESCRIPTION
REFERENCE INPUT SECTION
The reference input stage is shown below in Figure 2. SW1 and
SW2 are normally-closed switches. SW3 is normally-open. When
power-down is initiated, SW3 is closed and SW1 and SW2 are
opened. This ensures that there is no loading of the REFIN pin
on power-down.
POWER-DOWN
CONTROL
NC
The A and B CMOS counters combine with the dual modulus
prescaler to allow a wide ranging division ratio in the PLL
feedback counter. The counters are specified to work when the
prescaler output is 200 MHz or less, when VDD = 5 V. Typically,
they will work with 250 MHz output from the prescaler. Thus,
with an RF input frequency of 2.5 GHz, a prescaler value of
16/17 is valid, but a value of 8/9 is not valid.
100k
SW2
The A and B counters, in conjunction with the dual modulus
prescaler make it possible to generate output frequencies which
are spaced only by the Reference Frequency divided by R. The
equation for the VCO frequency is as follows:
fVCO = [(P × B) + A] × fREFIN/R
fVCO = Output Frequency of external voltage controlled
oscillator (VCO).
P
= Preset modulus of dual modulus prescaler (8/9,
16/17, etc.).
B
= Preset Divide Ratio of binary 13-bit counter
(3 to 8191).
A
= Preset Divide Ratio of binary 6-bit A counter
(0 to 63).
TO R COUNTER
REFIN NC
BUFFER
SW1
SW3
NO
NC = NO CONNECT
fREFIN = External reference frequency oscillator.
Figure 2. Reference Input Stage
R
RF/IF INPUT STAGE
= Preset divide ratio of binary 15-bit programmable reference counter (1 to 32767).
The RF/IF input stage is shown in Figure 3. It is followed by a
2-stage limiting amplifier to generate the CML (Current Mode
Logic) clock levels needed for the prescaler.
N = BP + A
FROM RF
INPUT STAGE
1.6V
BIAS
GENERATOR
PRESCALER
P/P + 1
AVDD
2k
MODULUS
CONTROL
2k
13-BIT BCOUNTER
TO PFD
LOAD
LOAD
5-BIT ACOUNTER
RFINA
Figure 4. RF/IF A and B Counters
RFINB
RF/IF COUNTER
AGND
Figure 3. RF/IF Input Stage
REV. A
The 15-bit RF/IF R counter allows the input reference frequency to be divided down to product the input clock to the
phase frequency detector (PFD). Division ratios from 1 to
32767 are allowed.
–9–
ADF4210/ADF4211/ADF4212/ADF4213
PHASE FREQUENCY DETECTOR (PFD) AND CHARGE
PUMP
Lock Detect
The PFD takes inputs from the R counter and N counter and
produces an output proportional to the phase and frequency
difference between them. Figure 5 is a simplified schematic.
The PFD includes a fixed-delay element that sets the width of
the antibacklash pulse. This is typically 3 ns. This pulse ensures
that there is no deadzone in the PFD transfer function and gives
a consistent reference spur level.
MUXOUT can be programmed for two types of lock detect:
Digital Lock Detect and Analog Lock Detect. Digital Lock
Detect is active high. It is set high when the phase error on three
consecutive Phase Detector cycles is less than 15 ns. It will stay
set high until a phase error of greater than 25 ns is detected on
any subsequent PD cycle. The N-channel open-drain analog
lock detect should be operated with an external pull-up resistor
of 10 kΩ nominal. When lock has been detected, it is high with
narrow low-going pulses.
VP
CHARGE
PUMP
HI
D1
Q1
RF/IF INPUT SHIFT REGISTER
UP
U1
R DIVIDER
CLR1
DELAY
CLR2
HI
D2
Q2
CP
U3
DOWN
The ADF421x family digital section includes a 24-bit input shift
register, a 14-bit IF R counter and a 18-bit IF N counter, comprising a 6-bit IF A counter and a 12-bit IF B counter. Also
present is a 14-bit RF R counter and an 18-bit RF N counter,
comprising a 6-bit RF A counter and a 12-bit RF B counter.
Data is clocked into the 24-bit shift register on each rising edge
of CLK. The data is clocked in MSB first. Data is transferred
from the shift register to one of four latches on the rising edge of
LE. The destination latch is determined by the state of the two
control bits (C2, C1) in the shift register. These are the two LSBs
DB1, DB0 as shown in the timing diagram of Figure 1. The
truth table for these bits is shown in Table VI. Table I shows a
summary of how the latches are programmed.
U2
Table I. C2, C1 Truth Table
N DIVIDER
CPGND
R DIVIDER
N DIVIDER
CP OUTPUT
Control Bits
C2
C1
Data Latch
0
0
1
1
IF R Counter
IF AB Counter (A and B)
RF R Counter
RF AB Counter (A and B)
0
1
0
1
Figure 5. RF/IF PFD Simplified Schematic and Timing
(In Lock)
MUXOUT AND LOCK DETECT
The output multiplexer on the ADF421x family allows the
user to access various internal points on the chip. The state of
MUXOUT is controlled by P3, P4, P11, and P12. See Tables
III and V. Figure 6 shows the MUXOUT section in block diagram form.
DVDD
IF ANALOG LOCK DETECT
IF R COUNTER OUTPUT
IF N COUNTER OUTPUT
IF/RF ANALOG LOCK DETECT
RF R COUNTER OUTPUT
RF N COUNTER OUTPUT
RF ANALOG LOCK DETECT
DIGITAL LOCK DETECT
MUX
MUXOUT
CONTROL
DGND
Figure 6. MUXOUT Circuit
–10–
REV. A
ADF4210/ADF4211/ADF4212/ADF4213
Table II. ADF421x Family Latch Summary
IF PD
POLARITY
THREE-STATE
CP
LOCK DETECT
PRECISION
IF CP CURRENT
SETTING
IF FO
IF R COUNTER LATCH
DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15
IF
CP2
IF
CP1
IF
CP0
P4
P3
P2
P1
CONTROL
BITS
15-BIT REFERENCE COUNTER
R15
R14
DB14
R13
DB13 DB12
R12
R11
DB11 DB10
R10
DB9
DB8
DB7
R8
R7
R6
R9
DB6
DB5
DB4
DB3
DB2
DB1
DB0
R5
R4
R3
R2
R1
C2 (0)
C1 (0)
IF POWERDOWN
IF CP
GAIN
IF N COUNTER LATCH
IF
PRESCALER
DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15
P8
P7
P6
P5
B12
B11
B10
B9
B8
DB14
B7
DB13 DB12
B6
B5
CONTROL
BITS
6-BIT A COUNTER
12-BIT B COUNTER
DB11 DB10
B4
B3
DB9
DB8
DB7
B2
B1
A6
DB6
DB5
DB4
DB3
DB2
DB1
DB0
A5
A4
A3
A2
A1
C2 (0)
C1 (1)
RF PD
POLARITY
THREE-STATE
CP
RF
LOCK DETECT
RF CP CURRENT
SETTING
RF FO
RF R COUNTER LATCH
DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15
RF
CP2
RF
CP1
RF
CP0
P12
P11
P10
P9
CONTROL
BITS
15-BIT REFERENCE COUNTER
R15
R14
DB14
R13
DB13 DB12
R12
R11
DB11 DB10
R10
R9
DB9
DB8
DB7
R8
R7
R6
DB6
DB5
DB4
DB3
DB2
DB1
DB0
R5
R4
R3
R2
R1
C2 (1)
C1 (0)
RF
POWERDOWN
RF CP
GAIN
RF N COUNTER LATCH
RF
PRESCALER
12-BIT B COUNTER
DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15
P17
REV. A
P16
P15
P14
B12
B11
B10
B9
B8
DB14
B7
DB13 DB12
B6
B5
CONTROL
BITS
6-BIT A COUNTER
DB11 DB10
B4
–11–
B3
DB9
DB8
DB7
B2
B1
A6
DB6
DB5
DB4
DB3
DB2
DB1
DB0
A5
A4
A3
A2
A1
C2 (1)
C1 (1)
ADF4210/ADF4211/ADF4212/ADF4213
Table III. IF R Counter Latch Map
IF PD
POLARITY
THREE-STATE
CP
IF CP CURRENT
SETTING
LOCK DETECT
PRECISION
IF FO
IF R COUNTER LATCH
DB23 DB22
DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14
IF
CP2
IF
CP0
IF
CP1
P4
P3
P2
P1
CONTROL
BITS
15-BIT REFERENCE COUNTER
R15
R14
R13
DB13 DB12
R12
P1
IF PD POLARITY
0
1
NEGATIVE
POSITIVE
P2
CHARGE PUMP OUTPUT
0
1
NORMAL
THREE-STATE
DB11 DB10
R11
R10
R9
DB9
DB8
DB7
R8
R7
R6
DB6
DB5
DB4
DB3
DB2
DB1
DB0
R5
R4
R3
R2
R1
C2 (0)
C1 (0)
R15
0
0
0
0
.
.
.
1
R14
0
0
0
0
.
.
.
1
R13
0
0
0
0
.
.
.
1
..........
..........
..........
..........
..........
..........
..........
..........
..........
R3
0
0
0
1
.
.
.
1
R2
0
1
1
0
.
.
.
0
R1
1
0
1
0
.
.
.
0
DIVIDE RATIO
1
2
3
4
.
.
.
32764
1
1
1
..........
1
0
1
32765
1
1
1
..........
1
1
0
32766
1
1
1
..........
1
1
1
32767
P12
P11
FROM RF R LATCH
P4
P3
MUXOUT
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
LOGIC LOW STATE
IF ANALOG LOCK DETECT
IF REFERENCE DIVIDER OUTPUT
IF N DIVIDER OUTPUT
RF ANALOG LOCK DETECT
RF/IF ANALOG LOCK DETECT
IF DIGITAL LOCK DETECT
LOGIC HIGH STATE
RF REFERENCE DIVIDER OUTPUT
RF N DIVIDER OUTPUT
THREE-STATE OUTPUT
IF COUNTER RESET
RF DIGITAL LOCK DETECT
RF/IF DIGITAL LOCK DETECT
RF COUNTER RESET
IF AND RF COUNTER RESET
IF CP1
0
0
1
1
0
0
1
1
IF CP0
0
1
0
1
0
1
0
1
ICP (mA)
IF CP2
0
0
0
0
1
1
1
1
1.5k
1.088
2.176
3.264
4.352
5.44
6.528
7.616
8.704
2.7k
0.625
1.25
1.875
2.5
3.125
3.75
4.375
5.0
5.6k
0.294
0.588
0.882
1.176
1.47
1.764
2.058
2.352
–12–
REV. A
ADF4210/ADF4211/ADF4212/ADF4213
Table IV. IF N Counter Latch Map
IF POWERDOWN
IF CP
GAIN
IF N COUNTER LATCH
DB23 DB22
P8
P7
IF
PRESCALER
DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14
P6
P5
B12
B11
B10
B9
P6
P5
IF PRESCALER
0
0
1
1
0
1
0
1
8/9
16/17
32/33
64/65
P7
IF POWER-DOWN
0
1
DISABLE
ENABLE
B8
B7
DB13 DB12
B6
DB11 DB10
B5
B4
B3
DB9
DB8
DB7
B2
B1
A6
DB6
DB5
DB4
DB3
DB2
DB1
DB0
A5
A4
A3
A2
A1
C2 (0)
C1 (1)
A6
A5
..........
A2
A1
A COUNTER
DIVIDE RATIO
0
0
0
0
.
.
.
1
1
1
1
0
0
0
0
.
.
.
1
1
1
1
..........
..........
..........
..........
..........
..........
..........
..........
..........
..........
..........
0
1
1
0
.
.
.
0
0
1
1
1
0
1
0
.
.
.
0
1
0
1
1
2
3
4
.
.
.
60
61
62
63
B12
B11
B10
B3
B2
B1
B COUNTER DIVIDE RATIO
0
0
.
.
.
1
0
0
.
.
.
1
0
0
.
.
.
1
..........
..........
..........
..........
..........
..........
0
1
.
.
.
1
1
0
.
.
.
0
1
0
.
.
.
0
3
4
.
.
.
4092
1
1
1
..........
1
0
1
4093
1
1
1
..........
1
1
0
4094
1
1
1
..........
1
1
1
4095
P8
IF CP GAIN
0
1
DISABLE
ENABLE
CONTROL
BITS
6-BIT A COUNTER
12-BIT B COUNTER
N = BP + A, P IS PRESCALER VALUE SET IN THE FUNCTION LATCH.
B MUST BE GREATER THAN OR EQUAL TO A. FOR CONTIGUOUS
VALUES OF N FREF, NMIN is (P2 – P).
REV. A
–13–
ADF4210/ADF4211/ADF4212/ADF4213
Table V. RF R Latch Map
RF PD
POLARITY
THREE-STATE
CP
RF CP CURRENT
SETTING
RF
LOCK DETECT
RF FO
RF R COUNTER LATCH
DB23 DB22
DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14
RF
CP2
RF
CP0
RF
CP1
P12
P11
P10
R15
P9
P9
0
1
P10
0
1
CONTROL
BITS
15-BIT REFERENCE COUNTER
R14
R13
DB13 DB12
R12
R11
DB11 DB10
R10
DB9
DB8
DB7
R8
R7
R6
R9
DB6
DB5
DB4
DB3
DB2
DB1
DB0
R5
R4
R3
R2
R1
C2 (1)
C1 (0)
R15
0
0
0
0
.
.
.
1
R14
0
0
0
0
.
.
.
1
R13
0
0
0
0
.
.
.
1
..........
..........
..........
..........
..........
..........
..........
..........
..........
R3
0
0
0
1
.
.
.
1
R2
0
1
1
0
.
.
.
0
R1
1
0
1
0
.
.
.
0
DIVIDE RATIO
1
2
3
4
.
.
.
32764
1
1
1
..........
1
0
1
32765
1
1
1
..........
1
1
0
32766
1
1
1
..........
1
1
1
32767
RF PD POLARITY
NEGATIVE
POSITIVE
CHARGE PUMP OUTPUT
NORMAL
THREE-STATE
P12
P11
FROM IF R LATCH
P4
P3
MUXOUT
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
LOGIC LOW STATE
IF ANALOG LOCK DETECT
IF REFERENCE DIVIDER OUTPUT
IF N DIVIDER OUTPUT
RF ANALOG LOCK DETECT
RF/IF ANALOG LOCK DETECT
IF DIGITAL LOCK DETECT
LOGIC HIGH STATE
RF REFERENCE DIVIDER OUTPUT
RF N DIVIDER OUTPUT
THREE-STATE OUTPUT
IF COUNTER RESET
RF DIGITAL LOCK DETECT
RF/IF DIGITAL LOCK DETECT
RF COUNTER RESET
IF AND RF COUNTER RESET
RF CP1
0
0
1
1
0
0
1
1
RF CP0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
ICP (mA)
RF CP2
0
0
0
0
1
1
1
1
1.5k
1.125
2.25
3.375
4.5
5.625
6.75
7.7875
9.0
2.7k
0.625
1.25
1.875
2.5
3.125
3.75
4.375
5.0
5.6k
0.301
0.602
0.904
1.205
1.506
1.808
2.109
2.411
–14–
REV. A
ADF4210/ADF4211/ADF4212/ADF4213
Table VI. RF N Counter Latch Map
RF POWERDOWN
RF CP
GAIN
RF N COUNTER LATCH
DB23 DB22
P17
P16
RF
PRESCALER
12-BIT B COUNTER
DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14
P15
P14
B12
B11
B10
B9
P15
P14
PRESCALER
0
0
1
1
0
1
0
1
8/9
16/17
32/33
64/65
P16
RF POWER-DOWN
0
1
DISABLE
ENABLE
B8
B7
DB13 DB12
B6
DB11 DB10
B5
B4
B3
DB9
DB8
DB7
B2
B1
A6
DB6
DB5
DB4
DB3
DB2
DB1
DB0
A5
A4
A3
A2
A1
C2 (1)
C1 (1)
A6
A5
..........
A2
A1
A COUNTER
DIVIDE RATIO
0
0
0
0
.
.
.
1
1
1
1
0
0
0
0
.
.
.
1
1
1
1
..........
..........
..........
..........
..........
..........
..........
..........
..........
..........
..........
0
1
1
0
.
.
.
0
0
1
1
1
0
1
0
.
.
.
0
1
0
1
1
2
3
4
.
.
.
60
61
62
63
B12
B11
B10
B3
B2
B1
B COUNTER DIVIDE RATIO
0
0
.
.
.
1
0
0
.
.
.
1
0
0
.
.
.
1
..........
..........
..........
..........
..........
..........
0
1
.
.
.
1
1
0
.
.
.
0
1
0
.
.
.
0
3
4
.
.
.
4092
1
1
1
..........
1
0
1
4093
1
1
1
..........
1
1
0
4094
1
1
1
..........
1
1
1
4095
P17
RF CP GAIN
0
1
DISABLE
ENABLE
CONTROL
BITS
6-BIT A COUNTER
N = BP + A, P IS PRESCALER VALUE SET IN THE FUNCTION LATCH. B
MUST BE GREATER THAN OR EQUAL TO A. FOR CONTIGUOUS
VALUES OF N FREF, NMIN is (P2 – P).
REV. A
–15–
ADF4210/ADF4211/ADF4212/ADF4213
PROGRAM MODES
IF SECTION
Table III and Table V show how to set up the Program Modes
in the ADF421x family. The following should be noted:
PROGRAMMABLE IF REFERENCE (R) COUNTER
1. IF and RF Analog Lock Detect indicate when the PLL is in
lock. When the loop is locked and either IF or RF Analog
Lock Detect is selected, the MUXOUT pin will show a logic
high with narrow low-going pulses. When the IF/RF Analog
Lock Detect is chosen, the locked condition is indicated only
when both IF and RF loops are locked.
2. The IF Counter Reset mode resets the R and AB counters in
the IF section and also puts the IF charge pump into threestate. The RF Counter Reset mode resets the R and AB
counters in the RF section and also puts the RF charge
pump into three-state. The IF and RF Counter Reset mode
does both of the above. Upon removal of the reset bits, the
AB counter resumes counting in close alignment with the R
counter (maximum error is one prescaler output cycle).
3. The Fastlock mode uses MUXOUT to switch a second loop
filter damping resistor to ground during Fastlock operation.
Activation of Fastlock occurs whenever RF CP Gain in the
RF Reference counter is set to one.
IF Power-Down
If control bits C2, C1 are 0, 0, the data is transferred from the
input shift register to the 14-bit IFR counter. Table III shows
the input shift register data format for the IFR counter and the
divide ratios possible.
IF Phase Detector Polarity
P1 sets the IF Phase Detector Polarity. When the IF VCO characteristics are positive this should be set to “1.” When they are
negative it should be set to “0.” See Table III.
IF Charge Pump Three-State
P2 puts the IF charge pump into three-state mode when programmed to a “1.” It should be set to “0” for normal operation.
See Table III.
IF PROGRAM MODES
Table III and Table V show how to set up the Program Modes
in the ADF421x family.
IF Charge Pump Currents
IFCP2, IFCP1, IFCP0 program current setting for the IF
charge pump. See Table III.
PROGRAMMABLE IF AB COUNTER
It is possible to program the ADF421x family for either synchronous or asynchronous power-down on either the IF or RF side.
If control bits C2, C1 are 0, 1, the data in the input register is used
to program the IF AB counter. The N counter consists of a 6-bit
swallow counter (A counter) and 12-bit programmable counter
(B counter). Table IV shows the input register data format for
programming the IF AB counter and the possible divide ratios.
Synchronous IF Power-Down
Programming a “1” to P7 of the ADF421x family will initiate a
power-down. If P2 of the ADF421x family has been set to “0”
(normal operation), a synchronous power-down is conducted.
The device will automatically put the charge pump into threestate and then complete the power-down.
IF Prescaler Value
P5 and P6 in the IF A, B Counter Latch sets the IF prescaler
value. See Table IV.
Asynchronous IF Power-Down
If P2 of the ADF421x family has been set to “1” (three-state the
IF charge pump), and P7 is subsequently set to “1,” an asynchronous power-down is conducted. The device will go into
power-down on the rising edge of LE, which latches the “1” to
the IF power-down bit (P7).
Synchronous RF Power-Down
Programming a “1” to P16 of the ADF421x family will initiate a
power-down. If P10 of the ADF421x family has been set to “0”
(normal operation), a synchronous power-down is conducted. The
device will automatically put the charge pump into three-state
and then complete the power-down.
IF Power-Down
Table III and Table V show the power-down bits in the
ADF421x family.
IF Fastlock
The IF CP Gain bit (P8) of the IF N register in the ADF421x
family is the Fastlock Enable Bit. Only when this is “1” is IF
Fastlock enabled. When Fastlock is enabled, the IF CP current
is set to its maximum value. Since the IF CP Gain bit is contained in the IF N Counter, only one write is needed to both
program a new output frequency and also initiate Fastlock. To
come out of Fastlock, the IF CP Gain bit on the IF N register
must be set to “0.” See Table IV.
Asynchronous RF Power-Down
If P10 of the ADF421x family has been set to “1” (three-state
the RF charge pump), and P16 is subsequently set to “1,” an
asynchronous power-down is conducted. The device will go into
power down on the rising edge of LE, which latches the “1” to
the RF power-down bit (P16).
Activation of either synchronous or asynchronous power-down
forces the IF/RF loop’s R and AB dividers to their load state
conditions and the IF/RF input section is debiased to a highimpedance state.
The REFIN oscillator circuit is only disabled if both the IF and
RF power-downs are set.
The input register and latches remain active and are capable of
loading and latching data during all the power-down modes.
The IF/RF section of the devices will return to normal powered
up operation immediately upon LE latching a “0” to the
appropriate power-down bit.
RF SECTION
PROGRAMMABLE RF REFERENCE (R) COUNTER
If control bits C2, C1 are 1, 0, the data is transferred from the
input shift register to the 14-bit RFR counter. Table V shows
the input shift register data format for the RFR counter and the
possible divide ratios.
RF Phase Detector Polarity
P9 sets the IF Phase Detector Polarity. When the RF VCO
characteristics are positive this should be set to “1.” When they
are negative it should be set to “0.” See Table V.
RF Charge Pump Three-State
P10 puts the RF charge pump into three-state mode when programmed to a “1.” It should be set to “0” for normal operation.
See Table V.
–16–
REV. A
ADF4210/ADF4211/ADF4212/ADF4213
RF PROGRAM MODES
APPLICATIONS SECTION
Local Oscillator for GSM Handset Receiver
Table III and Table V show how to set up the Program Modes
in the ADF421x family.
Figure 7 shows the ADF4210/ADF4211/ADF4212/ADF4213
being used with a VCO to produce the LO for a GSM base
station transmitter.
RF Charge Pump Currents
RFCP2, RFCP1, RFCP0 program current setting for the RF
charge pump. See Table V.
The reference input signal is applied to the circuit at FREFIN
and, in this case, is terminated in 50 Ω. A typical GSM system
would have a 13 MHz TCXO driving the reference input without any 50 Ω termination. In order to have a channel spacing of
200 kHz (the GSM standard), the reference input must be
divided by 65, using the on-chip reference.
PROGRAMMABLE RF N COUNTER
If control bits C2, C1 are 1, 1, the data in the input register is
used to program the RF N (A + B) counter. The N counter
consists of a 6-bit swallow counter (A Counter) and 12-bit
programmable counter (B Counter). Table IV shows the input
register data format for programming the RF N counter and the
possible divide ratios.
WIDEBAND PLL
Many of the wireless applications for synthesizers and VCOs in
PLLs are narrowband in nature. These applications include
various wireless standards such as GSM, DSC1800, CDMA, or
WCDMA. In each of these cases, the total tuning range for the
local oscillator is less than 100 MHz. However, there are also
wideband applications where the local oscillator could have up
to an octave tuning range. For example, cable TV tuners have
a total range of about 400 MHz. Figure 8 shows an application where the ADF4213 is used to control and program the
Micronetics M3500–1324. The loop filter was designed for an
RF output of 2100 MHz, a loop bandwidth of 40 kHz, a PFD
frequency of 1 MHz, ICP of 10 mA (2.5 mA synthesizer ICP
multiplied by the gain factor of 4), VCO KD of 80 MHz/V (sensitivity of the M3500–1324 at an output of 2100 MHz) and a
phase margin of 45°C.
RF Prescaler Value
P14 and P15 in the RF A, B Counter Latch sets the RF prescaler value. See Table VI.
RF Power-Down
Table III and Table V show the power-down bits in the
ADF421x family.
RF Fastlock
The RF CP Gain bit (P17) of the RF N register in the ADF421x
family is the Fastlock Enable Bit. Only when this is “1” is IF
Fastlock enabled. When Fastlock is enabled, the RF CP current
is set to its maximum value. Also an extra loop filter damping
resistor to ground is switched in using the FL O pin, thus compensating for the change in loop characteristics while in Fastlock.
Since the RF CP Gain bit is contained in the RF N Counter, only
one write is needed to both program a new output frequency and
also initiate Fastlock. To come out of Fastlock, the RF CP Gain bit
on the RF N register must be set to “0.” See Table VI.
In narrowband applications, there is generally a small variation
(less than 10%) in output frequency and also a small variation
(typically < 10%) in VCO sensitivity over the range. However,
RFOUT
IFOUT
VP
VDD
VP
100pF
100pF
18
18
VP2
VCC
18
100pF
VDD2 VDD1
18
VP1
3.3k
VCO190620pF
540T
VCC
3.3k
CPIF
CPRF
REFIN
1.3nF
1.3nF
5.6k
8.2nF
RSET
2.7k
ADF4210/
ADF4211/
ADF4212/
ADF4213
620pF
5.6k
18
VCO190- 100pF
18
902T
8.2nF
MUXOUT
LOCK
DETECT
100pF
100pF
DECOUPLING CAPACITORS (22F/10PF) ON VDD, VP OF THE
ADF4211/ADF4212/ADF4213 AND ON VCC OF THE VCOS HAVE
BEEN OMITTED FROM THE DIAGRAM TO AID CLARITY.
CLK
DATA
LE
51
SPI-COMPATIBLE SERIAL BUS
51
AGNDIF
RFINB
AGNDRF
1000pF 1000pF
FREFIN
DGNDIF
51
DGNDRF
RFIN
Figure 7. GSM Handset Receiver Local Oscillator Using the ADF4210/ADF4211/ADF4212/ADF4213
REV. A
–17–
ADF4210/ADF4211/ADF4212/ADF4213
20V
VP
VDD
100pF
1k
FREFIN
VDD1 VDD2 VP1 VP2
REFIN
CPRF
51
RSET
CE
CLK
DATA
LE
MUXOUT
100pF
18
27nF
130pF
18
OUT
18
M3500-1324
3.9nF
2.7k
GND
470
LOCK
DETECT
RFIN
100pF
DGNDIF
AGNDRF
ADF4213
DGNDRF
SPI-COMPATIBLE SERIAL BUS
VCC
V_TUNE
AD820
20k
51
DECOUPLING CAPACITORS ON VDD, VP OF THE ADF4213,
ON VCC OF THE AD820 AND ON THE VCC OF THE M3500-1324
HAVE BEEN OMITTED FROM THE DIAGRAM TO AID CLARITY.
THE IF SECTION OF THE CIRCUIT HAS ALSO BEEN OMITTED TO
SIMPLIFY THE SCHEMATIC.
AGNDIF
1000pF 1000pF
RFOUT
12V
3k
Figure 8. Wideband PLL Circuit
in wide-band applications both of these parameters have a much
greater variation. In Figure 8, for example, we have –25% and
+30% variation in the RF output from the nominal 1.8 GHz.
The sensitivity of the VCO can vary from 130 MHz/V at
1900 MHz to 30 MHz/V at 2400 MHz. Variations in these
parameters will change the loop bandwidth. This in turn can
affect stability and lock time. By changing the programmable
ICP, it is possible to obtain compensation for these varying
loop conditions and ensure that the loop is always operating
close to optimal conditions.
When operating in the mode described, the maximum SCLOCK
rate of the ADuC812 is 4 MHz. This means that the maximum
rate at which the output frequency can be changed will be about
180 kHz.
SCLOCK
MOSI
ADuC812
I/O PORTS
The maximum allowable serial clock rate is 20 MHz. This
means that the maximum update rate possible for the device is
909 kHz, or one update every 1.1 ms. This is certainly more
than adequate for systems that will have typical lock times in
hundreds of microseconds.
ADuC812 to ADF421x Family Interface
Figure 9 shows the interface between the ADF421x family and
the ADuC812 microconverter. Since the ADuC812 is based on
an 8051 core, this interface can be used with any 8051-based
microcontroller. The microconverter is set up for SPI Master
Mode with CPHA = 0. To initiate the operation, the I/O port
driving LE is brought low. Each latch of the ADF421x family
needs a 24-bit word. This is accomplished by writing three 8-bit
bytes from the microconverter to the device. When the third
byte has been written, the LE input should be brought high to
complete the transfer.
SDATA
LE
INTERFACING
The ADF4210/ADF4211/ADF4212/ADF4213 family has a
simple SPI-compatible serial interface for writing to the device.
SCLK, SDATA, and LE control the data transfer. When LE
(Latch Enable) goes high, the 22 bits that have been clocked
into the input register on each rising edge of SCLK will be
transferred to the appropriate latch. See Figure 1 for the Timing
Diagram and Table I for the Latch Truth Table.
SCLK
CE
ADF4210/
ADF4211/
ADF4212/
ADF4213
MUXOUT
(LOCK DETECT)
Figure 9. ADuC812 to ADF421x Family Interface
ADSP-21xx to ADF421x Family Interface
Figure 10 shows the interface between the ADF421x family and
the ADSP-21xx Digital Signal Processor. As previously discussed,
the ADF421x family needs a 24-bit serial word for each latch
write. The easiest way to accomplish this, using the ADSP-21xx
family, is to use the Autobuffered Transmit Mode of operation
with Alternate Framing. This provides a means for transmitting
an entire block of serial data before an interrupt is generated.
Set up the word length for eight bits and use three memory
locations for each 24-bit word. To program each 24-bit latch,
store the three 8-bit bytes, enable the Autobuffered mode, and
write to the transmit register of the DSP. This last operation
initiates the autobuffer transfer.
SCLK
DT
SDATA
ADSP-21xx
TFS
LE
CE
I/O FLAGS
On first applying power to the ADF421x family, it needs four
writes (one each to the R counter latch and the AB counter latch
for both RF1 and RF2 sides) for the output to become active.
SCLK
ADF4210/
ADF4211/
ADF4212/
ADF4213
MUXOUT
(LOCK DETECT)
Figure 10. ADSP-21xx to ADF421x Family Interface
–18–
REV. A
ADF4210/ADF4211/ADF4212/ADF4213
Thermal vias may be used on the printed circuit board thermal
pad to improve thermal performance of the package. If vias are
used, they should be incorporated in the thermal pad at 1.2 mm
grid pitch. The via diameter should be between 0.3 mm and
0.33 mm and the via barrel should be plated with 1 oz. copper
to plug the via. The user should connect the printed circuit
board pad to AGND.
PCB Guidelines for Chip Scale Package
The lands on the chip scale package (CP-20), are rectangular.
The printed circuit board pad for these should be 0.1 mm
longer than the package land length and 0.05 mm wider than
the package land width. The land should be centered on the
pad. This will ensure that the solder joint size is maximized.
The bottom of the chip scale package has a central thermal pad.
The thermal pad on the printed circuit board should be at least
as large as this exposed pad. On the printed circuit board, there
should be clearance of at least 0.25 mm between the thermal
pad and inner edges of the pad pattern. This will ensure that
shorting is avoided.
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
Thin Shrink Small Outline Package (TSSOP)
(RU-20)
0.260 (6.60)
0.252 (6.40)
20
11
0.177 (4.50)
0.169 (4.30)
0.256 (6.50)
0.246 (6.25)
1
10
PIN 1
0.006 (0.15)
0.002 (0.05)
SEATING
PLANE
0.0433 (1.10)
MAX
0.0256 (0.65) 0.0118 (0.30)
BSC
0.0075 (0.19)
0.0079 (0.20)
0.0035 (0.090)
8
0
0.028 (0.70)
0.020 (0.50)
Chip Scale Package
(CP-20)
0.024 (0.60)
0.017 (0.42)
0.009 (0.24)
0.024 (0.60)
0.017 (0.42)
16
0.009 (0.24)
15
0.157 (4.0)
BSC SQ
PIN 1
INDICATOR
TOP
VIEW
0.148 (3.75)
BSC SQ
0.031 (0.80) MAX
0.026 (0.65) NOM
12 MAX
0.035 (0.90) MAX
0.033 (0.85) NOM
SEATING
PLANE
0.020 (0.50)
BSC
0.008 (0.20)
REF
0.012 (0.30)
0.009 (0.23)
0.007 (0.18)
0.030 (0.75)
0.022 (0.60)
0.014 (0.50)
11
10
1
0.080 (2.25)
0.083 (2.10) SQ
0.077 (1.95)
6
0.080 (2.00)
REF
0.002 (0.05)
0.0004 (0.01)
0.0 (0.0)
–19–
20
BOTTOM
VIEW
CONTROLLING DIMENSIONS ARE IN MILLIMETERS
REV. A
0.010 (0.25)
MIN
5
ADF4210/ADF4211/ADF4212/ADF4213–Revision History
Location
Page
Data Sheet changed from REV. 0 to REV. A.
Changes to Test Conditions/Comments section of Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Edit to RFIN and IFIN Function text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
PRINTED IN U.S.A.
CP-20 Package replaced by CP-20[2] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
C01029–0–6/01(A)
PCB Guidelines for Chip Scale Package section added . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
–20–
REV. A