LINER LTC1709-7

■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
U
FEATURES
LTC1709-7
2-Phase, 5-Bit VID,
Current Mode, High Efficiency,
Synchronous Step-Down Switching Regulator
DESCRIPTIO
Output Stages Operate Antiphase Reducing Input
Capacitance Requirements and Power Supply
Induced Noise
Dual Input Supply Capability for Load Sharing
5-Bit Mobile VID Code: VOUT = 0.925V to 2V
Current Mode Control Ensures Current Sharing
True Remote Sensing Differential Amplifier
Power Good Output Indicator
OPTI-LOOPTM Compensation Minimizes COUT
Three Operational Modes: PWM, Burst and Cycle Skip
Programmable Fixed Frequency: 150kHz to 300kHz
±1% Output Voltage Accuracy
Wide VIN Range: 4V to 36V Operation
Adjustable Soft-Start Current Ramping
Internal Current Foldback and Short-Circuit Shutdown
Overvoltage Soft Latch Eliminates Nuisance Trips
Active Voltage Positioning Capable
Available in 36-Lead Narrow SSOP Package
U
APPLICATIO S
■
■
■
Mobile/Desktop Computers
Internet Servers
Large Memory Arrays
DC Power Distribution Systems
An operating mode select pin (FCB) can be used to regulate a secondary winding or select among three modes
including Burst ModeTM operation for highest efficiency. An
internal differential amplifier provides true remote sensing
of the regulated supply’s positive and negative output terminals as required in high current applications.
The RUN/SS pin provides soft-start and optional timed,
short-circuit shutdown. Current foldback limits MOSFET
dissipation during short-circuit conditions when the
overcurrent latchoff is disabled. OPTI-LOOP compensation
allows the transient response to be optimized for a wide
range of output capacitors and ESR values.
, LTC and LT are registered trademarks of Linear Technology Corporation.
OPTI-LOOP and Burst Mode are trademarks of Linear Technology Corporation.
U
■
The LTC®1709-7 is a 2-phase, VID programmable, synchronous step-down switching regulator controller that drives
two all N-channel external power MOSFET stages in a fixed
frequency architecture. The 2-phase controller drives its two
output stages out of phase at frequencies up to 300kHz to
minimize the RMS ripple currents in both input and output
capacitors. The 2-phase technique effectively multiplies the
fundamental frequency by two, improving transient response while operating each channel at an optimum frequency for efficiency. Thermal design is also simplified.
TYPICAL APPLICATIO
+
VIN
FCB
RUN/SS
3.3k
TG1
ITH
LTC1709-7
0.47µF
VIN
5V TO 28V
0.002Ω
1µH
SW1
S
BG1
PGND
SGND
PGOOD
5 VID BITS
S
BOOST1
220pF
VID0–VID4
SENSE1 +
SENSE1 –
TG2
BOOST2
EAIN
ATTENOUT
ATTENIN
BG2
VDIFFOUT
INTVCC
VOS –
SENSE2 +
VOS +
SENSE2 –
0.002Ω
0.47µF
VOUT
0.925V TO 2V
40A
1µH
SW2
+
0.1µF
10µF
35V
×4
10µF
+
COUT
1000µF
4V
×2
170989 F01
Figure 1. High Current Dual Phase Step-Down Converter
1
LTC1709-7
U
W W
W
ABSOLUTE
AXI U RATI GS
U
W
U
PACKAGE/ORDER I FOR ATIO
(Note 1)
Input Supply Voltage (VIN).........................36V to – 0.3V
Topside Driver Voltages (BOOST1,2) .........42V to – 0.3V
Switch Voltage (SW1, 2) .............................36V to – 5 V
SENSE1+, SENSE2 +, SENSE1–,
SENSE2 – Voltages ................... (1.1)INTVCC to – 0.3V
EAIN, VOS+, VOS–, EXTVCC, INTVCC, RUN/SS,
VBIAS, ATTENIN, ATTENOUT, PGOOD,
VID0–VID4, Voltages ...............................7V to – 0.3V
Boosted Driver Voltage (BOOST-SW) ..........7V to – 0.3V
PLLFLTR, PLLIN, VDIFFOUT,
FCB Voltages ................................... INTVCC to – 0.3V
ITH Voltage ................................................2.7V to – 0.3V
Peak Output Current <1µs(TGL1,2, BG1,2) ................ 3A
INTVCC RMS Output Current ................................ 50mA
Operating Ambient Temperature Range
(Note 2) .............................................. – 40°C to 85°C
Junction Temperature (Note 3) ............................. 125°C
Storage Temperature Range ................. – 65°C to 150°C
Lead Temperature (Soldering, 10 sec).................. 300°C
ORDER PART
NUMBER
TOP VIEW
RUNN/SS
1
36 NC
SENSE1 +
2
35 TG1
SENSE1 –
3
34 SW1
LTC1709EG-7
EAIN
4
33 BOOST1
PLLFLTR
5
32 VIN
PLLIN
6
31 BG1
FCB
7
30 EXTVCC
ITH
8
29 INTVCC
SGND
9
28 PGND
VDIFFOUT 10
VOS
–
11
27 BG2
26 BOOST2
VOS+ 12
25 SW2
SENSE2 – 13
24 TG2
SENSE2 + 14
23 PGOOD
ATTENOUT 15
22 VBIAS
ATTENIN 16
21 VID4
VID0 17
20 VID3
VID1 18
19 VID2
G PACKAGE
36-LEAD PLASTIC SSOP
TJMAX = 125°C, θJA = 85°C/W
Consult factory for Industrial and Military grade parts.
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VIN = 15V, VBIAS = 5V, VRUN/SS = 5V unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Main Control Loop
VEAIN
Regulated Feedback Voltage
ITH Voltage = 1.2V (Note 4)
●
0.792
0.800
0.808
VSENSEMAX
Maximum Current Sense Threshold
VSENSE – = 5V
●
62
75
88
mV
IINEAIN
Feedback Current
(Note 4)
–5
– 50
nA
VLOADREG
Output Voltage Load Regulation
(Note 4)
Measured in Servo Loop, ∆ITH Voltage: 1.2V to 0.7V
Measured in Servo Loop, ∆ITH Voltage: 1.2V to 2V
0.1
– 0.1
0.5
– 0.5
%
%
0.002
0.02
%/V
0.8
0.84
V
– 0.17
–1
µA
4.3
4.8
V
0.84
0.86
0.88
V
3
3.5
4
VREFLNREG
Reference Voltage Line Regulation
VFCB
Forced Continuous Threshold
IFCB
Forced Continuous Current
VBINHIBIT
Burst Inhibit (Constant Frequency)
Threshold
Measured at FCB pin
VOVL
Output Overvoltage Threshold
Measured at VEAIN
UVLO
Undervoltage Lockout
VIN Ramping Down
gm
Transconductance Amplifier gm
ITH = 1.2V, Sink/Source 5µA (Note 4)
gmOL
Transconductance Amplifier Gain
ITH = 1.2V, (gm × ZL; No Ext Load) (Note 4)
2
●
●
VIN = 3.6V to 30V (Note 4)
●
●
0.76
V
V
3
mmho
1.5
V/mV
LTC1709-7
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VIN = 15V, VBIAS = 5V, VRUN/SS = 5V unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
IQ
Input DC Supply Current
Normal Mode
Shutdown
(Note 5)
EXTVCC Tied to VOUT, VOUT = 5V
VRUN/SS = 0V
MIN
TYP
MAX
470
20
40
UNITS
µA
µA
µA
IRUN/SS
Soft-Start Charge Current
VRUN/SS = 1.9V
– 0.5
–1.2
VRUN/SS
RUN/SS Pin ON Arming
VRUN/SS Rising
1.0
1.5
1.9
VRUN/SSLO
RUN/SS Pin Latchoff Arming
VRUN/SS Rising from 3V
4.1
4.5
V
ISCL
RUN/SS Discharge Current
Soft Short Condition VEAIN = 0.5V, VRUN/SS = 4.5V
2
4
µA
ISDLHO
Shutdown Latch Disable Current
VEAIN = 0.5V
1.6
5
µA
ISENSE
Total Sense Pins Source Current
Each Channel: VSENSE1 –, 2 – = VSENSE1+, 2 + = 0V
– 85
– 60
µA
DFMAX
Maximum Duty Factor
In Dropout
98
99.5
%
TG1, 2 tr
TG1, 2 tf
Top Gate Transition Time:
Rise Time
Fall Time
(Note 6)
CLOAD = 3300pF
CLOAD = 3300pF
30
40
90
90
ns
ns
BG1, 2 tr
BG1, 2 tf
Bottom Gate Transition Time:
Rise Time
Fall Time
(Note 6)
CLOAD = 3300pF
CLOAD = 3300pF
30
20
90
90
ns
ns
TG/BG t1D
Top Gate Off to Bottom Gate On Delay
Synchronous Switch-On Delay Time
CLOAD = 3300pF Each Driver (Note 6)
90
ns
BG/TG t2D
Bottom Gate Off to Top Gate On Delay
Top Switch-On Delay Time
CLOAD = 3300pF Each Driver (Note 6)
90
ns
tON(MIN)
Minimum On-Time
Tested with a Square Wave (Note 7)
180
ns
0.5
V
Internal VCC Regulator
VINTVCC
Internal VCC Voltage
6V < VIN < 30V, VEXTVCC = 4V
4.8
VLDO INT
INTVCC Load Regulation
ICC = 0 to 20mA, VEXTVCC = 4V
0.2
1.0
%
VLDO EXT
EXTVCC Voltage Drop
ICC = 20mA, VEXTVCC = 5V
80
160
mV
VEXTVCC
EXTVCC Switchover Voltage
ICC = 20mA, EXTVCC Ramping Positive
VLDOHYS
EXTVCC Switchover Hysteresis
ICC = 20mA, EXTVCC Ramping Negative
●
4.5
5.0
5.2
V
4.7
V
0.2
V
VID Parameters
VBIAS
Operating Supply Voltage Range
RATTEN
Resistance Between ATTENIN
and ATTENOUT Pins
ATTENERR
Resistive Divider Error
RPULLUP
VID0 to VID4 Pull-Up Resistance
VIDTHLOW
VID0 to VID4 Logic Threshold Low
VIDTHHIGH
VID0 to VID4 Logic Threshold High
VIDLEAK
VID0 to VID4 Leakage
2.7
5.5
10
●
– 0.25
(Note 8)
V
kΩ
– 0.25
40
%
kΩ
0.4
1.6
V
V
VBIAS < VID0–VID4 < 7V
1
µA
kHz
Oscillator and Phase-Locked Loop
fNOM
Nominal Frequency
fLOW
fHIGH
RPLLIN
PLLIN Input Resistance
IPLLFLTR
Phase Detector Output Current
Sinking Capability
Sourcing Capability
RRELPHS
VPLLFLTR = 1.2V
190
220
250
Lowest Frequency
VPLLFLTR = 0V
120
140
160
kHz
Highest Frequency
VPLLFLTR ≥ 2.4V
280
310
360
kHz
Controller 2-Controller 1 Phase
fPLLIN < fOSC
fPLLIN > fOSC
50
kΩ
– 15
15
µA
µA
180
Deg
3
LTC1709-7
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VIN = 15V, VBIAS = 5V, VRUN/SS = 5V unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
0.1
0.3
V
±1
µA
PGOOD Output
VPGL
PGOOD Voltage Low
IPGOOD = 2mA
IPGOOD
PGOOD Leakage Current
VPGOOD = 5V
VPG
PGOOD Trip Level, Either Controller
VEAIN with Respect to Set Output Voltage
VEAIN Ramping Negative
VEAIN Ramping Positive
–6
6
– 7.5
7.5
– 9.5
9.5
%
%
0.995
1
1.005
V/V
Differential Amplifier/Op Amp Gain Block
ADA
Gain
CMRRDA
Common Mode Rejection Ratio
0V < VCM < 5V
RIN
Input Resistance
Measured at VOS + Input
Note 1: Absolute Maximum Ratings are those values beyond which the
life of a device may be impaired.
Note 2: The LTC1709EG-7 is guaranteed to meet performance
specifications from 0°C to 70°C. Specifications over the – 40°C to 85°C
operating temperature range are assured by design, characterization and
correlation with statistical process controls.
Note 3: TJ is calculated from the ambient temperature TA and power
dissipation PD according to the following formula:
LTC1709EG-7: TJ = TA + (PD • 85°C/W)
Note 4: The LTC1709-7 is tested in a feedback loop that servos VITH to a
specified voltage and measures the resultant VEAIN.
46
55
dB
80
kΩ
Note 5: Dynamic supply current is higher due to the gate charge being
delivered at the switching frequency. See Applications Information.
Note 6: Rise and fall times are measured using 10% and 90% levels. Delay
times are measured using 50% levels.
Note 7: The minimum on-time condition corresponds to the on inductor
peak-to-peak ripple current ≥ 40% IMAX (see Minimum On-Time
Considerations in the Applications Information section).
Note 8: Each built-in pull-up resistor attached to the VID inputs also has a
series diode to allow input voltages higher than the VIDVCC supply without
damage or clamping (see the Applications Information section).
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Efficiency vs Load Current
(3 Operating Modes) (Figure 12)
100
100
80
IOUT = 20A
70
FORCED
CONTINUOUS
MODE
60
50
CONSTANT
FREQUENCY
(BURST DISABLE)
40
30
20
VIN = 5V
VOUT = 1.6V
FREQ = 200kHz
10
0
0.01
VOUT = 2V
90
VIN = 5V
EFFICIENCY (%)
EFFICIENCY (%)
80
0.1
10
1
LOAD CURRENT (A)
100
17097 G01
4
100
Burst Mode
OPERATION
EFFICIENCY (%)
90
Efficiency vs Input Voltage
(Figure 12)
Efficiency vs Output Current
(Figure 12)
VIN = 8V
60
VIN = 12V
VIN = 20V
40
VOUT = 2V
VEXTVCC = 0V
FREQ = 200kHz
VFCB = 0V
20
0
0.1
1
10
OUTPUT CURRENT (A)
100
17097 G02
VOUT = 1.6V
80
70
60
50
5
15
10
INPUT VOLTAGE (V)
20
17097 G03
LTC1709-7
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Supply Current vs Input Voltage
and Mode
INTVCC and EXTVCC Switch
Voltage vs Temperature
EXTVCC Voltage Drop
1000
5.05
INTVCC AND EXTVCC SWITCH VOLTAGE (V)
250
ON
EXTVCC VOLTAGE DROP (mV)
SUPPLY CURRENT (µA)
800
600
400
200
200
150
100
50
SHUTDOWN
0
0
5
20
15
10
25
INPUT VOLTAGE (V)
30
0
35
0
10
30
20
CURRENT (mA)
40
17097 G04
50
4.95
4.90
4.85
4.80
4.70
– 50 – 25
100
125
Maximum Current Sense Threshold
vs Percent of Nominal Output
Voltage (Foldback)
Maximum Current Sense Threshold
vs Duty Factor
75
80
ILOAD = 1mA
70
60
4.8
4.7
50
VSENSE (mV)
4.9
VSENSE (mV)
INTVCC VOLTAGE (V)
50
25
75
0
TEMPERATURE (°C)
17097 G06
5.0
25
4.6
50
40
30
20
4.5
10
0
4.4
0
5
20
15
25
10
INPUT VOLTAGE (V)
30
0
35
20
40
60
DUTY FACTOR (%)
80
Maximum Current Sense Threshold
vs VRUN/SS (Soft-Start)
80
0
100
50
100
0
25
75
PERCENT OF NOMINAL OUTPUT VOLTAGE (%)
17097 G08
17097 G07
17097 G09
Current Sense Threshold
vs ITH Voltage
Maximum Current Sense Threshold
vs Sense Common Mode Voltage
90
80
VSENSE(CM) = 1.6V
80
70
76
40
60
VSENSE (mV)
VSENSE (mV)
60
VSENSE (mV)
EXTVCC SWITCHOVER THRESHOLD
4.75
17097 G05
Internal 5V LDO Line Reg
5.1
INTVCC VOLTAGE
5.00
72
68
50
40
30
20
10
20
0
64
–10
–20
0
0
1
2
3
4
5
6
VRUN/SS (V)
17097 G10
60
0
1
3
4
2
COMMON MODE VOLTAGE (V)
5
17097 G11
–30
0
0.5
1
1.5
VITH (V)
2
2.5
17097 G12
5
LTC1709-7
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Load Regulation
SENSE Pins Total Source Current
VITH vs VRUN/SS
2.5
FCB = 0V
VIN = 15V
FIGURE 1
100
VOSENSE = 0.7V
2.0
–0.2
50
ISENSE (µA)
–0.1
VITH (V)
NORMALIZED VOUT (%)
0.0
1.5
1.0
–0.3
0
–50
0.5
–0.4
1
0
3
2
LOAD CURRENT (A)
0
4
5
0
1
2
3
4
5
6
0
VRUN/SS (V)
2
Maximum Current Sense
Threshold vs Temperature
6
17097 G15
RUN/SS Current vs Temperature
Soft-Start Up (Figure 12)
1.8
80
1.6
RUN/SS CURRENT (µA)
78
76
74
72
VITH
1V/DIV
1.4
1.2
VOUT
2V/DIV
1.0
VRUN/SS
2V/DIV
0.8
0.6
0.4
100ms/DIV
0.2
70
–50 –25
50
25
0
75
TEMPERATURE (°C)
100
125
0
–50
–25
0
25
50
75
TEMPERATURE (°C)
17097 G16
100
125
VOUT(AC)
20mV/DIV
VOUT
50mV/DIV
VIN = 15V, VOUT = 1.6V, IL = 200mARMS
VOUT(AC)
20mV/DIV
IL1
1A/DIV
IOUT
0/20A
FCB = 0V
IL2
1A/DIV
FCB = OPEN
17097 G19
VIN = 15V, VOUT = 1.6V, IL = 400mARMS
IL1
1A/DIV
IL2
1A/DIV
20µs/DIV
Constant Frequency Mode
(Figure 12)
Burst Mode Operation (Figure 12)
VIN = 15V, VOUT = 1.6V
17097 G18
17097 G17
Load Step (Figure 12)
6
4
VSENSE COMMON MODE VOLTAGE (V)
17097 G14
17097 G13
VSENSE (mV)
–100
FCB = INTVCC
10µs/DIV
17097 G25
2µs/DIV
17097 G26
LTC1709-7
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Current Sense Pin Input Current
vs Temperature
10
VOUT = 5V
350
VFREQSET = 5V
33
31
29
27
50
25
0
75
TEMPERATURE (°C)
100
125
300
8
FREQUENCY (kHz)
EXTVCC SWITCH RESISTANCE (Ω)
CURRENT SENSE INPUT CURRENT (µA)
35
25
–50 –25
Oscillator Frequency
vs Temperature
EXTVCC Switch Resistance
vs Temperature
6
4
VFREQSET = 0V
150
100
50
0
–50 –25
50
25
0
75
TEMPERATURE (°C)
100
125
0
– 50 – 25
50
25
75
0
TEMPERATURE (°C)
100
125
17097 G22
17097 G21
Undervoltage Lockout
vs Temperature
VRUN/SS Shutdown Latch
Thresholds vs Temperature
4.5
SHUTDOWN LATCH THRESHOLDS (V)
3.50
UNDERVOLTAGE LOCKOUT (V)
VFREQSET = OPEN
200
2
17097 G20
3.45
3.40
3.35
3.30
3.25
3.20
–50 –25
250
50
25
75
0
TEMPERATURE (°C)
100
125
17097 G23
LATCH ARMING
4.0
3.5
3.0
LATCHOFF
THRESHOLD
2.5
2.0
1.5
1.0
0.5
0
–50
–25
0
25
50
75
TEMPERATURE (°C)
100
125
17097 G24
U
U
U
PI FU CTIO S
RUN/SS (Pin 1): Combination of Soft-Start, Run Control
Input and Short-Circuit Detection Timer. A capacitor to
ground at this pin sets the ramp time to full current output.
Forcing this pin below 0.8V causes the IC to shut down all
internal circuitry. All functions are disabled in shutdown.
SENSE1+, SENSE2+ (Pins 2,14): The (+) Input to Each
Differential Current Comparator. The ITH pin voltage and
built-in offsets between SENSE– and SENSE+ pins in
conjunction with RSENSE set the current trip threshold.
SENSE1–, SENSE2– (Pins 3, 13): The (–) Input to the
Differential Current Comparators.
EAIN (Pin 4): Input to the error amplifier that compares the
feedback voltage to the internal 0.8V reference voltage.
This pin is normally connected to a resistive divider from
the output of the differential amplifier (DIFFOUT).
7
LTC1709-7
U
U
U
PI FU CTIO S
PLLFLTR (Pin 5): The phase-locked loop’s lowpass filter
is tied to this pin. Alternatively, this pin can be driven with
an AC or DC voltage source to vary the frequency of the
internal oscillator.
PLLIN (Pin 6): External Synchronization Input to Phase
Detector. This pin is internally terminated to SGND with
50kΩ. The phase-locked loop will force the rising top gate
signal of controller 1 to be synchronized with the rising
edge of the PLLIN signal.
FCB (Pin 7): Forced Continuous Control Input. This input
acts on both output stages and can be used to regulate a
secondary winding. Pulling this pin below 0.8V will force
continuous synchronous operation. Do not leave this pin
floating without a decoupling capacitor.
ITH (Pin 8): Error Amplifier Output and Switching Regulator Compensation Point. Both current comparator’s thresholds increase with this control voltage. The normal voltage
range of this pin is from 0V to 2.4V
SGND (Pin 9): Signal Ground. This pin is common to both
controllers. Route separately to the PGND pin.
VDIFFOUT (Pin 10): Output of a Differential Amplifier. This
pin provides true remote output voltage sensing. VDIFFOUT
normally drives an external resistive divider that sets the
output voltage.
VOS–, VOS+ (Pins 11, 12): Inputs to an Operational Amplifier. Internal precision resistors configure it as a differential amplifier whose output is VDIFFOUT.
ATTENOUT (Pin 15): Voltage Feedback Signal Resistively
Divided According to the VID Programming Code.
ATTENIN (Pin 16): The Input to the VID Controlled Resistive Divider.
VID0–VID4 (Pins 17,18, 19, 20, 21): VID Control Logic
Input Pins.
VBIAS (Pin 22): Supply Pin for the VID Control Circuit.
PGOOD (Pin 23): Open-Drain Logic Output. PGOOD is
pulled to ground when the voltage on the EAIN pin is not
within ±7.5% of its set point.
TG2, TG1 (Pins 24, 35): High Current Gate Drives for Top
N-Channel MOSFETS. These are the outputs of floating
drivers with a voltage swing equal to INTVCC superimposed on the switch node voltage SW.
SW2, SW1 (Pins 25, 34): Switch Node Connections to
Inductors. Voltage swing at these pins is from a Schottky
diode (external) voltage drop below ground to VIN.
BOOST2, BOOST1 (Pins 26, 33): Bootstrapped Supplies
to the Topside Floating Drivers. External capacitors are
connected between the BOOST and SW pins, and Schottky
diodes are connected between the BOOST and INTVCC
pins.
BG2, BG1 (Pins 27, 31): High Current Gate Drives for
Bottom N-Channel MOSFETS. Voltage swing at these pins
is from ground to INTVCC.
PGND (Pin 28): Driver Power Ground. Connect to sources
of bottom N-channel MOSFETS and the (–) terminals of
CIN.
INTVCC (Pin 29): Output of the Internal 5V Linear Low
Dropout Regulator and the EXTVCC Switch. The driver and
control circuits are powered from this voltage source.
Decouple to power ground with a 1µF ceramic capacitor
placed directly adjacent to the IC and minimum of 4.7µF
additional tantalum or other low ESR capacitor.
EXTVCC (Pin 30): External Power Input to an Internal
Switch. This switch closes and supplies INTVCC, bypassing the internal low dropout regulator whenever EXTVCC is
higher than 4.7V. See EXTVCC Connection in the Applications Information section. Do not exceed 7V on this pin
and ensure VEXTVCC ≤ VINTVCC.
VIN (Pin 32): Main Supply Pin. Should be closely decoupled
to the IC’s signal ground pin.
NC (Pin 36): Do Not Connect.
8
LTC1709-7
W
FU CTIO AL DIAGRA
U
U
PLLIN
PHASE DET
fIN
50k
RLP PLLFLTR
CLP
CLK1
OSCILLATOR
CLK2
TO SECOND
CHANNEL
PGOOD
–
DUPLICATE FOR SECOND
CONTROLLER CHANNEL
BOOST
DROP
OUT
DET
0.86V
EAIN
–
S
Q
R
Q
BOT
B
COUT
+
PGND
SHDN
•
–
+
–
++
–
–
0.18µA
SLOPE
COMP
+
45k
–
2.4V
FCB
VREF
0.80V
–
EA
+
VIN
4.8V
+
–
EXTVCC
CSEC
45k
+
R5
DSEC
–
30k SENSE
–
FCB
VIN
+
30k SENSE
+
0.86V
4(VFB)
3V
•
INTVCC
I2
+
DIFFOUT
4.5V
VOUT
RSENSE
+
I1
5V
BG
–
A1
VSEC
CIN
INTVCC
BOT
–
VOS +
+
SW
SWITCH
LOGIC
+
CB
FCB
TOP ON
0.55V
DB
D1
0.74V
VOS –
R6
TG
TOP
+
+
VIN
INTVCC
OV
5V
LDO
REG
VFB
EAIN
0.80V
+
–
0.86V
ITH
CC
1.2µA
INTVCC
SHDN
RST
4(VFB)
+
6V
INTERNAL
SUPPLY
SGND
RUN
SOFT
START
CC2
RC
RUN/SS
CSS
ATTENIN
10k
5-BIT VID DECODER
ATTENOUT
TYPICAL ALL
VID PINS
40k
R1
VID0
VID1
VID2
VID3
VID4
VBIAS
17097 FBD
9
LTC1709-7
U
OPERATIO
(Refer to Functional Diagram)
Main Control Loop
The LTC1709-7 uses a constant frequency, current mode
step-down architecture with the two output stages operating 180 degrees out of phase. During normal operation,
each top MOSFET is turned on when the clock for that
channel sets the RS latch, and turned off when the main
current comparator, I1, resets the RS latch. The peak
inductor current at which I1 resets the RS latch is controlled by the voltage on the ITH pin, which is the output of
error amplifier EA. The EAIN pin receives the voltage
feedback signal, which is compared to the internal reference voltage by the EA. When the load current increases,
it causes a slight decrease in VEAIN relative to the 0.8V
reference, which in turn causes the ITH voltage to increase
until the average inductor current matches the new load
current. After the top MOSFET has turned off, the bottom
MOSFET is turned on until either the inductor current
starts to reverse, as indicated by current comparator I2, or
the beginning of the next cycle.
The top MOSFET drivers are biased from floating bootstrap capacitor CB, which normally is recharged during
each off cycle through an external diode when the top
MOSFET turns off. As VIN decreases to a voltage close to
VOUT, the loop may enter dropout and attempt to turn on
the top MOSFET continuously. The dropout detector detects this and forces the top MOSFET off for about 500ns
every tenth cycle to allow CB to recharge.
The main control loop is shut down by pulling the RUN/
SS pin low. Releasing RUN/SS allows an internal 1.2µA
current source to charge soft-start capacitor CSS. When
CSS reaches 1.5V, the main control loop is enabled with
the ITH voltage clamped at approximately 30% of its
maximum value. As CSS continues to charge, the ITH pin
voltage is gradually released allowing normal, full-current
operation.
Low Current Operation
The FCB pin is a multifunction pin providing two functions: 1) to provide regulation for a secondary winding by
temporarily forcing continuous PWM operation on
both controllers; and 2) select between two modes of low
10
current operation. When the FCB pin voltage is below
0.80V, the controller forces continuous PWM current
mode operation. In this mode, the top and bottom
MOSFETs are alternately turned on to maintain the output
voltage independent of direction of inductor current.
When the FCB pin is below VINTVCC␣ –␣ 2V but greater than
0.80V, the controller enters Burst Mode operation. Burst
Mode operation sets a minimum output current level
before inhibiting the top switch and turns off the synchronous MOSFET(s) when the inductor current goes negative. This combination of requirements will, at low currents,
force the ITH pin below a voltage threshold that will
temporarily inhibit turn-on of both output MOSFETs until
the output voltage drops. There is 60mV of hysteresis in
the burst comparator B tied to the ITH pin. This hysteresis
produces output signals to the MOSFETs that turn them
on for several cycles, followed by a variable “sleep”
interval depending upon the load current. The resultant
output voltage ripple is held to a very small value by
having the hysteretic comparator after the error amplifier
gain block.
Constant Frequency Operation
When the FCB pin is tied to INTVCC, Burst Mode operation
is disabled and a forced minimum peak output current
requirement is removed. This provides constant frequency,
discontinuous (preventing reverse inductor current) current operation over the widest possible output current
range. This constant frequency operation is not as efficient
as Burst Mode operation, but does provide a lower noise,
constant frequency operating mode down to approximately 1% of designed maximum output current.
Continuous Current (PWM) Operation
Tying the FCB pin to ground will force continuous current
operation. This is the least efficient operating mode, but
may be desirable in certain applications. The output can
source or sink current in this mode. When sinking current
while in forced continuous operation, current will be
forced back into the main power supply potentially boosting the input supply to dangerous voltage levels—
BEWARE!
LTC1709-7
U
OPERATIO
(Refer to Functional Diagram)
Frequency Synchronization
Output Overvoltage Protection
The phase-locked loop allows the internal oscillator to be
synchronized to an external source via the PLLIN pin. The
output of the phase detector at the PLLFLTR pin is also the
DC frequency control input of the oscillator that operates
over a 140kHz to 310kHz range corresponding to a DC
voltage input from 0V to 2.4V. When locked, the PLL aligns
the turn on of the top MOSFET to the rising edge of the
synchronizing signal. When PLLIN is left open, the PLLFLTR
pin goes low, forcing the oscillator to minimum frequency.
An overvoltage comparator, OV, guards against transient
overshoots (>7.5%) as well as other more serious conditions that may overvoltage the output. In this case, the top
MOSFET is turned off and the bottom MOSFET is turned on
until the overvoltage condition is cleared.
Input capacitance ESR requirements and efficiency losses
are substantially reduced because the peak current drawn
from the input capacitor is effectively divided by two and
power loss is proportional to the RMS current squared. A
two stage, single output voltage implementation can
reduce input path power loss by 75% and radically reduce
the required RMS current rating of the input capacitor(s).
INTVCC/EXTVCC Power
Power for the top and bottom MOSFET drivers and most
of the IC circuitry is derived from INTVCC. When the
EXTVCC pin is left open, an internal 5V low dropout
regulator supplies INTVCC power. If the EXTVCC pin is
taken above 4.7V, the 5V regulator is turned off and an
internal switch is turned on connecting EXTVCC to INTVCC.
This allows the INTVCC power to be derived from a high
efficiency external source such as the output of the regulator itself or a secondary winding, as described in the
Applications Information section. An external Schottky
diode can be used to minimize the voltage drop from
EXTVCC to INTVCC in applications requiring greater than
the specified INTVCC current. Voltages up to 7V can be
applied to EXTVCC for additional gate drive capability.
Differential Amplifier
This amplifier provides true differential output voltage
sensing. Sensing both VOUT + and VOUT – benefits regulation in high current applications and/or applications
having electrical interconnection losses. The amplifier is
not capable of sinking current and therefore must be
resistively loaded to do so.
Power Good (PGOOD)
The PGOOD pin is connected to the drain of an internal
MOSFET. The MOSFET turns on when the output voltage
is not within ±7.5% of its nominal output level as determined by the feedback divider. When the output is within
±7.5% of its nominal value, the MOSFET is turned off
within 10µs and the PGOOD pin should be pulled up by an
external resistor to a source of up to 7V.
Short-Circuit Detection
The RUN/SS capacitor is used initially to limit the inrush
current from the input power source. Once the controllers have been given time, as determined by the capacitor
on the RUN/SS pin, to charge up the output capacitors
and provide full-load current, the RUN/SS capacitor is
then used as a short-circuit timeout circuit. If the output
voltage falls to less than 70% of its nominal output
voltage the RUN/SS capacitor begins discharging assuming that the output is in a severe overcurrent and/or
short-circuit condition. If the condition lasts for a long
enough period as determined by the size of the RUN/SS
capacitor, the controller will be shut down until the
RUN/SS pin voltage is recycled. This built-in latchoff can
be overidden by providing a current >5µA at a compliance of 5V to the RUN/SS pin. This current shortens the
soft-start period but also prevents net discharge of the
RUN/SS capacitor during a severe overcurrent and/or
short-circuit condition. Foldback current limiting is activated when the output voltage falls below 70% of its
nominal level whether or not the short-circuit latchoff
circuit is enabled.
11
LTC1709-7
U
W
U
U
APPLICATIO S I FOR ATIO
RSENSE Selection For Output Current
RSENSE1, 2 are chosen based on the required peak output
current. The LTC1709-7 current comparator has a maximum threshold of 75mV/RSENSE and an input common
mode range of SGND to 1.1(INTVCC). The current comparator threshold sets the peak inductor current, yielding
a maximum average output current IMAX equal to the peak
value less half the peak-to-peak ripple current, ∆IL.
Assuming a common input power source for each output
stage and allowing a margin for variations in the
LTC1709-7 and external component values yields:
RSENSE = 2(50mV/IMAX)
Operating Frequency
The LTC1709-7 uses a constant frequency, phase-lockable architecture with the frequency determined by an
internal capacitor. This capacitor is charged by a fixed
current plus an additional current which is proportional
to the voltage applied to the PLLFLTR pin. Refer to PhaseLocked Loop and Frequency Synchronization for additional information.
12
A graph for the voltage applied to the PLLFLTR pin vs
frequency is given in Figure␣ 2. As the operating frequency
is increased the gate charge losses will be higher, reducing
efficiency (see Efficiency Considerations). The maximum
switching frequency is approximately 310kHz.
2.5
PLLFLTR PIN VOLTAGE (V)
The basic LTC1709-7 application circuit is shown in
Figure␣ 1 on the first page. External component selection
begins with the selection of the inductor(s) based on
ripple current requirements and continues with the
RSENSE1, 2 resistor selection using the calculated peak
inductor current and/or maximum current limit. Next, the
power MOSFETs and D1 and D2 are selected. The operating frequency and the inductor are chosen based mainly
on the amount of ripple current. Finally, CIN is selected for
its ability to handle the input ripple current (that
PolyPhaseTM operation minimizes) and COUT is chosen
with low enough ESR to meet the output ripple voltage
and load step specifications (also minimized with
PolyPhase). Current mode architecture provides inherent
current sharing between output stages. The circuit shown
in Figure␣ 1 can be configured for operation up to an input
voltage of 28V (limited by the external MOSFETs). Current
mode control allows the ability to connect the two output
stages to two different input power supply rails. A heavy
output load can take some power from each input supply
according to the selection of the RSENSE resistors.
2.0
1.5
1.0
0.5
0
120
170
220
270
OPERATING FREQUENCY (kHz)
320
17097 F02
Figure 2. Operating Frequency vs VPLLFLTR
Inductor Value Calculation and Output Ripple Current
The operating frequency and inductor selection are interrelated in that higher operating frequencies allow the use
of smaller inductor and capacitor values. So why would
anyone ever choose to operate at lower frequencies with
larger components? The answer is efficiency. A higher
frequency generally results in lower efficiency because
MOSFET gate charge and transition losses increase directly with frequency. In addition to this basic tradeoff, the
effect of inductor value on ripple current and low current
operation must also be considered. The PolyPhase approach reduces both input and output ripple currents
while optimizing individual output stages to run at a lower
fundamental frequency, enhancing efficiency.
The inductor value has a direct effect on ripple current.
The inductor ripple current ∆IL per individual section, N,
decreases with higher inductance or frequency and
increases with higher VIN or VOUT:
∆IL =
VOUT  VOUT 
 1−

fL 
VIN 
where f is the individual output stage operating frequency.
PolyPhase is a registered trademark of Linear Technology Corporation.
LTC1709-7
U
W
U
U
APPLICATIO S I FOR ATIO
In a 2-phase converter, the net ripple current seen by the
output capacitor is much smaller than the individual
inductor ripple currents due to ripple cancellation. The
details on how to calculate the net output ripple current
can be found in Application Note 77.
Figure 3 shows the net ripple current seen by the output
capacitors for the 1- and 2- phase configurations. The
output ripple current is plotted for a fixed output voltage as
the duty factor is varied between 10% and 90% on the
x-axis. The output ripple current is normalized against the
inductor ripple current at zero duty factor. The graph can
be used in place of tedious calculations, simplifying the
design process.
Accepting larger values of ∆IL allows the use of low
inductances, but can result in higher output voltage ripple.
A reasonable starting point for setting ripple current is
∆IL = 0.4(IOUT)/2, where IOUT is the total load current.
Remember, the maximum ∆IL occurs at the maximum
input voltage. The individual inductor ripple currents are
determined by the inductor, input and output voltages.
1.0
1-PHASE
2-PHASE
0.9
0.8
ferrite, molypermalloy, or Kool Mµ® cores. Actual core
loss is independent of core size for a fixed inductor value,
but it is very dependent on inductance selected. As inductance increases, core losses go down. Unfortunately,
increased inductance requires more turns of wire and
therefore copper losses will increase.
Ferrite designs have very low core loss and are preferred
at high switching frequencies, so design goals can concentrate on copper loss and preventing saturation. Ferrite
core material saturates “hard,” which means that inductance collapses abruptly when the peak design current is
exceeded. This results in an abrupt increase in inductor
ripple current and consequent output voltage ripple. Do
not allow the core to saturate!
Molypermalloy (from Magnetics, Inc.) is a very good, low
loss core material for toroids, but it is more expensive
than ferrite. A reasonable compromise from the same
manufacturer is Kool Mµ. Toroids are very space efficient, especially when you can use several layers of wire.
Because they lack a bobbin, mounting is more difficult.
However, designs for surface mount are available which
do not increase the height significantly.
Power MOSFET, D1 and D2 Selection
Two external power MOSFETs must be selected for each
output stage with the LTC1709-7: one N-channel MOSFET
for the top (main) switch, and one N-channel MOSFET for
the bottom (synchronous) switch.
0.6
VO/fL
∆IO(P-P)
0.7
0.5
0.4
0.3
0.2
Inductor Core Selection
The peak-to-peak drive levels are set by the INTVCC
voltage. This voltage is typically 5V during start-up
(see EXTVCC Pin Connection). Consequently, logic-level
threshold MOSFETs must be used in most applications.
The only exception is if low input voltage is expected
(VIN < 5V); then, sublogic-level threshold MOSFETs
(VGS(TH) < 1V) should be used. Pay close attention to the
BVDSS specification for the MOSFETs as well; most of the
logic-level MOSFETs are limited to 30V or less.
Once the values for L1 and L2 are known, the type of
inductor must be selected. High efficiency converters
generally cannot afford the core loss found in low cost
powdered iron cores, forcing the use of more expensive
Selection criteria for the power MOSFETs include the “ON”
resistance RDS(ON), reverse transfer capacitance CRSS,
input voltage and maximum output current. When the
LTC1709-7 is operating in continuous mode the duty
0.1
0
0.1
0.2
0.3 0.4 0.5 0.6 0.7
DUTY FACTOR (VOUT/VIN)
0.8
0.9
17097 F03
Figure 3. Normalized Output Ripple Current
vs Duty Factor [IRMS ≈ 0.3 (∆IO(P–P))]
Kool Mµ is a registered trademark of Magnetics, Inc.
13
LTC1709-7
U
U
W
U
APPLICATIO S I FOR ATIO
factors for the top and bottom MOSFETs of each output
stage are given by:
Main Switch Duty Cycle =
VOUT
VIN
V –V 
Synchronous Switch Duty Cycle =  IN OUT 


VIN
The MOSFET power dissipations at maximum output
current are given by:
2
I

V
PMAIN = OUT  MAX  1 + δ RDS(ON) +
VIN  2 

2 I
k VIN  MAX  CRSS f
 2 
( )
(
( )
)( )
2
I

V –V
PSYNC = IN OUT  MAX  1 + δ RDS(ON)
VIN
 2 
( )
where δ is the temperature dependency of RDS(ON) and k
is a constant inversely related to the gate drive current.
Both MOSFETs have I2R losses but the topside N-channel
equation includes an additional term for transition losses,
which peak at the highest input voltage. For VIN < 20V the
high current efficiency generally improves with larger
MOSFETs, while for VIN > 20V the transition losses rapidly
increase to the point that the use of a higher RDS(ON) device
with lower CRSS actual provides higher efficiency. The
synchronous MOSFET losses are greatest at high input
voltage when the top switch duty factor is low or during a
short-circuit when the synchronous switch is on close to
100% of the period.
The term (1 + δ) is generally given for a MOSFET in the
form of a normalized RDS(ON) vs temperature curve, but
δ = 0.005/°C can be used as an approximation for low
voltage MOSFETs. CRSS is usually specified in the
MOSFET characteristics. The constant k = 1.7 can be
used to estimate the contributions of the two terms in the
main switch dissipation equation.
14
The Schottky diodes, D1 and D2 shown in Figure 1
conduct during the dead-time between the conduction of
the two large power MOSFETs. This helps prevent the
body diode of the bottom MOSFET from turning on,
storing charge during the dead-time, and requiring a
reverse recovery period which would reduce efficiency. A
1A to 3A Schottky (depending on output current) diode is
generally a good compromise for both regions of operation due to the relatively small average current. Larger
diodes result in additional transition losses due to their
larger junction capacitance.
CIN and COUT Selection
In continuous mode, the source current of each top
N-channel MOSFET is a square wave of duty cycle VOUT/
VIN. A low ESR input capacitor sized for the maximum
RMS current must be used. The details of a closed form
equation can be found in Application Note 77. Figure 4
shows the input capacitor ripple current for a 2-phase
configuration with the output voltage fixed and input
voltage varied. The input ripple current is normalized
against the DC output current. The graph can be used in
place of tedious calculations. The minimum input ripple
current can be achieved when the input voltage is twice the
output voltage
In the graph of Figure 4, the 2-phase local maximum input
RMS capacitor currents are reached when:
VOUT 2k − 1
=
VIN
4
where k = 1, 2
These worst-case conditions are commonly used for
design because even significant deviations do not offer
much relief. Note that capacitor manufacturer’s ripple
current ratings are often based on only 2000 hours of life.
This makes it advisable to further derate the capacitor, or
to choose a capacitor rated at a higher temperature than
required. Several capacitors may also be paralleled to
meet size or height requirements in the design. Always
consult the capacitor manufacturer if there is any
question.
LTC1709-7
U
W
U
U
APPLICATIO S I FOR ATIO
0.5
DC LOAD CURRENT
RMS INPUT RIPPLE CURRNET
0.6
0.4
1-PHASE
2-PHASE
0.3
0.2
0.1
0
0.1
0.2
0.3 0.4 0.5 0.6 0.7
DUTY FACTOR (VOUT/VIN)
0.8
0.9
17097 F04
Figure 4. Normalized RMS Input Ripple Current
vs Duty Factor for 1 and 2 Output Stages
It is important to note that the efficiency loss is proportional to the input RMS current squared and therefore a
2-phase implementation results in 75% less power loss
when compared to a single phase design. Battery/input
protection fuse resistance (if used), PC board trace and
connector resistance losses are also reduced by the
reduction of the input ripple current in a 2-phase system.
The required amount of input capacitance is further
reduced by the factor, 2, due to the effective increase in
the frequency of the current pulses.
The selection of COUT is driven by the required effective
series resistance (ESR). Typically once the ESR requirement has been met, the RMS current rating generally far
exceeds the IRIPPLE(P-P) requirements. The steady state
output ripple (∆VOUT) is determined by:

1 
∆VOUT ≈ ∆IRIPPLE  ESR +

16 fCOUT 

Where f = operating frequency of each stage, COUT =
output capacitance and ∆IRIPPLE = combined inductor
ripple currents.
The output ripple varies with input voltage since ∆IL is a
function of input voltage. The output ripple will be less than
50mV at max VIN with ∆IL = 0.4IOUT(MAX)/2 assuming:
COUT required ESR < 4(RSENSE) and
COUT > 1/(16f)(RSENSE)
The emergence of very low ESR capacitors in small,
surface mount packages makes very physically small
implementations possible. The ability to externally compensate the switching regulator loop using the I TH
pin(OPTI-LOOP compensation) allows a much wider selection of output capacitor types. OPTI-LOOP compensation effectively removes constraints on output capacitor
ESR. The impedance characteristics of each capacitor
type are significantly different than an ideal capacitor and
therefore require accurate modeling or bench evaluation
during design.
Manufacturers such as Nichicon, United Chemicon and
Sanyo should be considered for high performance
through-hole capacitors. The OS-CON semiconductor
dielectric capacitor available from Sanyo and the Panasonic
SP surface mount types have the lowest (ESR)(size)
product of any aluminum electrolytic at a somewhat
higher price. An additional ceramic capacitor in parallel
with OS-CON type capacitors is recommended to reduce
the inductance effects.
In surface mount applications, multiple capacitors may
have to be paralleled to meet the ESR or RMS current
handling requirements of the application. Aluminum electrolytic and dry tantalum capacitors are both available in
surface mount configurations. New special polymer surface mount capacitors offer very low ESR also but have
much lower capacitive density per unit volume. In the case
of tantalum, it is critical that the capacitors are surge tested
for use in switching power supplies. Several excellent
choices are the AVX TPS, AVX TPSV or the KEMET T510
series of surface mount tantalums, available in case heights
ranging from 2mm to 4mm. Other capacitor types include
Sanyo OS-CON, Nichicon PL series and Sprague 595D
series. Consult the manufacturer for other specific recommendations. A combination of capacitors will often result
in maximizing performance and minimizing overall cost
and size.
INTVCC Regulator
An internal P-channel low dropout regulator produces 5V
at the INTVCC pin from the VIN supply pin. The INTVCC
regulator powers the drivers and internal circuitry of the
LTC1709-7. The INTVCC pin regulator can supply up to
15
LTC1709-7
U
W
U
U
APPLICATIO S I FOR ATIO
50mA peak and must be bypassed to power ground with
a minimum of 4.7µF tantalum or electrolytic capacitor. An
additional 1µF ceramic capacitor placed very close to the
IC is recommended due to the extremely high instantaneous currents required by the MOSFET gate drivers.
High input voltage applications in which large MOSFETs
are being driven at high frequencies may cause the maximum junction temperature rating for the LTC1709-7 to be
exceeded. The supply current is dominated by the gate
charge supply current, in addition to the current drawn
from the differential amplifier output. The gate charge is
dependent on operating frequency as discussed in the
Efficiency Considerations section. The supply current can
either be supplied by the internal 5V regulator or via the
EXTVCC pin. When the voltage applied to the EXTVCC pin
is less than 4.7V, all of the INTVCC load current is supplied
by the internal 5V linear regulator. Power dissipation for
the IC is higher in this case by (IIN)(VIN – INTVCC) and
efficiency is lowered. The junction temperature can be
estimated by using the equations given in Note 1 of the
Electrical Characteristics. For example, the LTC1709-7 VIN
current is limited to less than 24mA from a 24V supply:
TJ = 70°C + (24mA)(24V)(85°C/W) = 119°C
Use of the EXTVCC pin reduces the junction temperature
to:
TJ = 70°C + (24mA)(5V)(85°C/W) = 80.2°C
The input supply current should be measured while the
controller is operating in continuous mode at maximum
VIN and the power dissipation calculated in order to
prevent the maximum junction temperature from being
exceeded.
EXTVCC Connection
The LTC1709-7 contains an internal P-channel MOSFET
switch connected between the EXTVCC and INTVCC pins.
When the voltage applied to EXTVCC rises above 4.7V, the
internal regulator is turned off and an internal switch
closes, connecting the EXTVCC pin to the INTVCC pin
thereby supplying internal and MOSFET gate driving power
to the IC. The switch remains closed as long as the voltage
16
applied to EXTVCC remains above 4.5V. This allows the
MOSFET driver and control power to be derived from the
output during normal operation (4.7V < VEXTVCC < 7V) and
from the internal regulator when the output is out of
regulation (start-up, short-circuit). Do not apply greater
than 7V to the EXTVCC pin and ensure that EXTVCC < VIN +
0.3V when using the application circuits shown. If an
external voltage source is applied to the EXTVCC pin when
the VIN supply is not present, a diode can be placed in
series with the LTC1709-7’s VIN pin and a Schottky diode
between the EXTVCC and the VIN pin, to prevent current
from backfeeding VIN.
Significant efficiency gains can be realized by powering
INTVCC from the output, since the VIN current resulting
from the driver and control currents will be scaled by the
ratio: (Duty Factor)/(Efficiency). For 5V regulators this
means connecting the EXTVCC pin directly to VOUT. However, for 3.3V and other lower voltage regulators, additional supply circuitry is required to derive INTVCC power
from the output.
The following list summarizes the four possible connections for EXTVCC:
1. EXTVCC left open (or grounded). This will cause INTVCC
to be powered from the internal 5V regulator resulting in
a significant efficiency penalty at high input voltages.
2. EXTVCC connected directly to VOUT. This is the normal
connection for a 5V regulator and provides the highest
efficiency.
3. EXTVCC connected to an external supply. If an external
supply is available in the 5V to 7V range, it may be used to
power EXTVCC providing it is compatible with the MOSFET
gate drive requirements.
4. EXTVCC connected to an output-derived boost network.
For 3.3V and other low voltage regulators, efficiency gains
can still be realized by connecting EXTVCC to an outputderived voltage which has been boosted to greater than
4.7V but less than 7V. This can be done with either the
inductive boost winding as shown in Figure 5a or the
capacitive charge pump shown in Figure 5b. The charge
pump has the advantage of simple magnetics.
LTC1709-7
U
W
U
U
APPLICATIO S I FOR ATIO
OPTIONAL EXTVCC
CONNECTION
5V < VSEC < 7V
+
+
VIN
CIN
VIN
VIN
1N4148
TG1
LTC1709-7
VSEC
1µF
N-CH
T1
R6
N-CH
LTC1709-7
BAT85
BAT85
RSENSE
VOUT
SW1
COUT
BG1
VOUT
L1
+
+
BG1
COUT
N-CH
N-CH
R5
0.22µF
VN2222LL
EXTVCC
RSENSE
SW1
BAT85
TG1
+
EXTVCC
FCB
+
VIN
CIN
PGND
PGND
17097 F05b
17097 F05a
Figure 5a. Secondary Output Loop with EXTVCC Connection
Topside MOSFET Driver Supply (CB,DB) (Refer to
Functional Diagram)
External bootstrap capacitors CB1 and CB2 connected to
the BOOST1 and BOOST2 pins supply the gate drive
voltages for the topside MOSFETs. Capacitor CB in the
Functional Diagram is charged though diode DB from
INTVCC when the SW pin is low. When the topside MOSFET
turns on, the driver places the CB voltage across the gatesource of the desired MOSFET. This enhances the MOSFET
and turns on the topside switch. The switch node voltage,
SW, rises to VIN and the BOOST pin rises to VIN + VINTVCC.
The value of the boost capacitor CB needs to be 30 to 100
times that of the total input capacitance of the topside
MOSFET(s). The reverse breakdown of DB must be greater
than VIN(MAX).
The final arbiter when defining the best gate drive amplitude level will be the input supply current. If a change is
made that decreases input current, the efficiency has
improved. If the input current does not change then the
efficiency has not changed either.
Output Voltage
The LTC1709-7 has a true remote voltage sense capablity.
The sensing connections should be returned from the load
back to the differential amplifier’s inputs through a common, tightly coupled pair of PC traces. The differential
amplifier corrects for DC drops in both the power and
ground paths. The differential amplifier output signal is
Figure 5b. Capacitive Charge Pump for EXTVCC
divided down and compared with the internal precision
0.8V voltage reference by the error amplifier.
Output Voltage Programming
The output voltage is digitally programmed as defined in
Table 1 using the VID0 to VID4 logic input pins. The VID
logic inputs program a precision, 0.25% internal feedback
resistive divider. The LTC1709-7 has an output voltage
range of 0.9V to 2V in 25mV and 50mV steps.
Between the ATTENOUT pin and ground is a variable
resistor, R1, whose value is controlled by the five VID input
pins (VID0 to VID4). Another resistor, R2, between the
ATTENIN and the ATTENOUT pins completes the resistive
divider. The output voltage is thus set by the ratio of
(R1␣ +␣ R2) to R1.
Each VID digital input is pulled up by a 40k resistor in
series with a diode from VBIAS. Therefore, it must be
grounded to get a digital low input, and can be either
floated or connected to VBIAS to get a digital high input. The
series diode is used to prevent the digital inputs from
being damaged or clamped if they are driven higher than
VBIAS. The digital inputs accept CMOS voltage levels.
VBIAS is the supply voltage for the VID section. It is
normally connected to INTVCC but can be driven from
other sources. If it is driven from another source, that
source must be in the range of 2.7V to 5.5V and must be
alive prior to enabling the LTC1709-7.
17
LTC1709-7
U
U
W
U
APPLICATIO S I FOR ATIO
Soft-Start/Run Function
Table 1. VID Output Voltage Programming
VID4
VID3
VID2
VID1
VID0
LTC1709-7
0
0
0
0
0
2.000V
0
0
0
0
1
1.950V
0
0
0
1
0
1.900V
0
0
0
1
1
1.850V
0
0
1
0
0
1.800V
0
0
1
0
1
1.750V
0
0
1
1
0
1.700V
0
0
1
1
1
1.650V
0
1
0
0
0
1.600V
0
1
0
0
1
1.550V
0
1
0
1
0
1.500V
0
1
0
1
1
1.450V
0
1
1
0
0
1.400V
0
1
1
0
1
1.350V
0
1
1
1
0
1.300V
0
1
1
1
1
*
1
0
0
0
0
1.275V
1
0
0
0
1
1.250V
1
0
0
1
0
1.225V
1
0
0
1
1
1.200V
1
0
1
0
0
1.175V
1
0
1
0
1
1.150V
1
0
1
1
0
1.125V
1
0
1
1
1
1.100V
1
1
0
0
0
1.075V
1
1
0
0
1
1.050V
1
1
0
1
0
1.025V
1
1
0
1
1
1.000V
1
1
1
0
0
0.975V
1
1
1
0
1
0.950V
1
1
1
1
0
0.925V
1
1
1
1
1
No_CPU/
Shutdown*
*Represents codes without a defined output voltage as specified in Intel
specifications. The LTC1709-7 interprets these codes as a valid input and
produces an output voltage as follows:
(11111) = 0.900V
(01111) = 1.250V
18
The RUN/SS pin provides three functions: 1) Run/Shutdown, 2) soft-start and 3) a defeatable short-circuit latchoff
timer. Soft-start reduces the input power sources’ surge
currents by gradually increasing the controller’s current
limit ITH(MAX). The latchoff timer prevents very short,
extreme load transients from tripping the overcurrent
latch. A small pull-up current (>5µA) supplied to the RUN/
SS pin will prevent the overcurrent latch from operating.
The following explanation describes how the functions
operate.
An internal 1.2µA current source charges up the soft-start
capacitor, CSS. When the voltage on RUN/SS reaches
1.5V, the controller is permitted to start operating. As the
voltage on RUN/SS increases from 1.5V to 3.0V, the
internal current limit is increased from 25mV/RSENSE to
75mV/RSENSE. The output current limit ramps up slowly,
taking an additional 1.4s/µF to reach full current. The
output current thus ramps up slowly, reducing the starting
surge current required from the input power supply. If
RUN/SS has been pulled all the way to ground there is a
delay before starting of approximately:
tDELAY =
(
)
1.5V
CSS = 1.25s /µF CSS
1.2µA
The time for the output current to ramp up is then:
tIRAMP =
(
)
3V − 1.5V
CSS = 1.25s /µF CSS
1.2µA
By pulling the RUN/SS pin below 0.8V the LTC1709-7 is
put into low current shutdown (IQ < 40µA). The RUN/SS
pins can be driven directly from logic as shown in Figure
6. Diode D1 in Figure 6 reduces the start delay but allows
CSS to ramp up slowly providing the soft-start function.
The RUN/SS pin has an internal 6V zener clamp (see
Functional Diagram).
LTC1709-7
U
W
U
U
APPLICATIO S I FOR ATIO
INTVCC
VIN
3.3V OR 5V
D1
RUN/SS
RSS*
RSS*
D1*
RUN/SS
CSS
CSS
*OPTIONAL TO DEFEAT OVERCURRENT LATCHOFF
17097 F06
Figure 6. RUN/SS Pin Interfacing
Fault Conditions: Overcurrent Latchoff
The RUN/SS pin also provides the ability to latch off the
controllers when an overcurrent condition is detected. The
RUN/SS capacitor, CSS, is used initially to limit the inrush
current of both controllers. After the controllers have been
started and been given adequate time to charge up the
output capacitors and provide full load current, the RUN/
SS capacitor is used for a short-circuit timer. If the output
voltage falls to less than 70% of its nominal value after CSS
reaches 4.1V, CSS begins discharging on the assumption
that the output is in an overcurrent condition. If the
condition lasts for a long enough period as determined by
the size of the CSS, the controller will be shut down until the
RUN/SS pin voltage is recycled. If the overload occurs
during start-up, the time can be approximated by:
tLO1 ≈ (CSS • 0.6V)/(1.2µA) = 5 • 105 (CSS)
If the overload occurs after start-up, the voltage on CSS will
continue charging and will provide additional time before
latching off:
tLO2 ≈ (CSS • 3V)/(1.2µA) = 2.5 • 106 (CSS)
This built-in overcurrent latchoff can be overridden by
providing a pull-up resistor, RSS, to the RUN/SS pin as
shown in Figure 6. This resistance shortens the soft-start
period and prevents the discharge of the RUN/SS capacitor during a severe overcurrent and/or short-circuit condition. When deriving the 5µA current from VIN as in the
figure, current latchoff is always defeated. The diode
connecting this pull-up resistor to INTVCC, as in Figure␣ 6,
eliminates any extra supply current during shutdown
while eliminating the INTVCC loading from preventing
controller start-up.
Why should you defeat current latchoff? During the
prototyping stage of a design, there may be a problem with
noise pickup or poor layout causing the protection circuit
to latch off the controller. Defeating this feature allows
troubleshooting of the circuit and PC layout. The internal
short-circuit and foldback current limiting still remains
active, thereby protecting the power supply system from
failure. A decision can be made after the design is complete whether to rely solely on foldback current limiting or
to enable the latchoff feature by removing the pull-up
resistor.
The value of the soft-start capacitor CSS may need to be
scaled with output voltage, output capacitance and load
current characteristics. The minimum soft-start capacitance is given by:
CSS > (COUT )(VOUT)(10-4)(RSENSE)
The minimum recommended soft-start capacitor of CSS =
0.1µF will be sufficient for most applications.
Phase-Locked Loop and Frequency Synchronization
The LTC1709-7 has a phase-locked loop comprised of an
internal voltage controlled oscillator and phase detector.
This allows the top MOSFET turn-on to be locked to the
rising edge of an external source. The frequency range of
the voltage controlled oscillator is ±50% around the
center frequency fO. A voltage applied to the PLLFLTR pin
of 1.2V corresponds to a frequency of approximately
220kHz. The nominal operating frequency range of the
LTC1709-7 is 140kHz to 310kHz.
The phase detector used is an edge sensitive digital type
which provides zero degrees phase shift between the
external and internal oscillators. This type of phase detector will not lock up on input frequencies close to the
harmonics of the VCO center frequency. The PLL hold-in
range, ∆fH, is equal to the capture range, ∆fC:
∆fH = ∆fC = ±0.5 fO (150kHz-300kHz)
The output of the phase detector is a complementary pair
of current sources charging or discharging the external
filter network on the PLLFLTR pin. A simplified block
diagram is shown in Figure 7.
19
LTC1709-7
U
U
W
U
APPLICATIO S I FOR ATIO
2.4V
PHASE
DETECTOR
tON(MIN) <
RLP
10k
CLP
EXTERNAL
OSC
PLLFLTR
PLLIN
50k
DIGITAL
PHASE/
FREQUENCY
DETECTOR
OSC
1709 F07
Figure 7. Phase-Locked Loop Block Diagram
If the external frequency (fPLLIN) is greater than the oscillator frequency f0SC, current is sourced continuously,
pulling up the PLLFLTR pin. When the external frequency
is less than f0SC, current is sunk continuously, pulling
down the PLLFLTR pin. If the external and internal frequencies are the same but exhibit a phase difference, the
current sources turn on for an amount of time corresponding to the phase difference. Thus the voltage on the
PLLFLTR pin is adjusted until the phase and frequency of
the external and internal oscillators are identical. At this
stable operating point the phase comparator output is
open and the filter capacitor CLP holds the voltage. The
LTC1709-7 PLLIN pin must be driven from a low impedance source such as a logic gate located close to the pin.
The loop filter components (CLP, RLP) smooth out the
current pulses from the phase detector and provide a
stable input to the voltage controlled oscillator. The filter
components CLP and RLP determine how fast the loop
acquires lock. Typically RLP =10k and CLP is 0.01µF to
0.1µF.
Minimum On-Time Considerations
Minimum on-time, tON(MIN), is the smallest time duration
that the LTC1709-7 is capable of turning on the top
MOSFET. It is determined by internal timing delays and the
gate charge required to turn on the top MOSFET. Low duty
cycle applications may approach this minimum on-time
limit and care should be taken to ensure that:
20
VOUT
()
VIN f
If the duty cycle falls below what can be accommodated by
the minimum on-time, the LTC1709-7 will begin to skip
cycles resulting in variable frequency operation. The output voltage will continue to be regulated, but the ripple
current and ripple voltage will increase.
The minimum on-time for the LTC1709-7 is generally less
than 200ns. However, as the peak sense voltage decreases, the minimum on-time gradually increases. This is
of particular concern in forced continuous applications
with low ripple current at light loads. If the duty cycle drops
below the minimum on-time limit in this situation, a
significant amount of cycle skipping can occur with correspondingly larger ripple current and voltage ripple.
If an application can operate close to the minimum
on-time limit, an inductor must be chosen that has a low
enough inductance to provide sufficient ripple amplitude
to meet the minimum on-time requirement. As a general
rule, keep the inductor ripple current of each phase equal
to or greater than 15% of IOUT(MAX) at VIN(MAX).
FCB Pin Operation
The FCB pin can be used to regulate a secondary winding
or as a logic level input. Continuous operation is forced
when the FCB pin drops below 0.8V. During continuous
mode, current flows continuously in the transformer primary. The secondary winding(s) supply current only when
the bottom, synchronous switch is on. When primary load
currents are low and/or the VIN/VOUT ratio is low, the
synchronous switch may not be on for a sufficient amount
of time to transfer power from the output capacitor to the
secondary load. Forced continuous operation will support
secondary windings providing there is sufficient synchronous switch duty factor. Thus, the FCB input pin removes
the requirement that power must be drawn from the
inductor primary in order to extract power from the
auxiliary winding(s). With the loop in continuous mode,
the auxiliary output(s) may nominally be loaded without
regard to the primary output load.
LTC1709-7
U
W
U
U
APPLICATIO S I FOR ATIO
The secondary output voltage VSEC is normally set as
shown in Figure 5a by the turns ratio N of the transformer:
VSEC ≅ (N + 1) VOUT
INTVCC
RT2
ITH
However, if the controller goes into Burst Mode operation
and halts switching due to a light primary load current,
then VSEC will droop. An external resistive divider from
VSEC to the FCB pin sets a minimum voltage VSEC(MIN):
 R6 
VSEC(MIN) ≈ 0.8 V 1 + 
 R5 
where R5 and R6 are shown in the Functional Diagram.
If VSEC drops below this level, the FCB voltage forces
temporary continuous switching operation until VSEC is
again above its minimum.
In order to prevent erratic operation if no external connections are made to the FCB pin, the FCB pin has a 0.18µA
internal current source pulling the pin high. Include this
current when choosing resistor values R5 and R6.
The following table summarizes the possible states available on the FCB pin:
Table 2
FCB Pin
Condition
0V to 0.75V
Forced Continuous (Current Reversal
Allowed—Burst Inhibited)
0.85V < VFCB < 4.3V
Minimum Peak Current Induces
Burst Mode Operation
No Current Reversal Allowed
Feedback Resistors
Regulating a Secondary Winding
>4.8V
Burst Mode Operation Disabled
Constant Frequency Mode Enabled
No Current Reversal Allowed
No Minimum Peak Current
Voltage Positioning
Voltage positioning can be used to minimize peak-to-peak
output voltage excursion under worst-case transient loading conditions. The open-loop DC gain of the control loop
is reduced depending upon the maximum load step specifications. Voltage positioning can easily be added to the
LTC1709-7 by loading the ITH pin with a resistive divider
having a Thevenin equivalent voltage source equal to the
RT1
RC
LTC1709-7
CC
17097 F08
Figure 8. Active Voltage Positioning Applied to the LTC1709-7
midpoint operating voltage of the error amplifier, or 1.2V
(see Figure 8).
The resistive load reduces the DC loop gain while maintaining the linear control range of the error amplifier. The
worst-case peak-to-peak output voltage deviation due to
transient loading can theoretically be reduced to half or
alternatively the amount of output capacitance can be
reduced for a particular application. A complete explanation is included in Design Solutions 10 or the LTC1736
data sheet. (See www.linear-tech.com)
Efficiency Considerations
The percent efficiency of a switching regulator is equal to
the output power divided by the input power times 100%.
It is often useful to analyze individual losses to determine
what is limiting the efficiency and which change would
produce the most improvement. Percent efficiency can be
expressed as:
%Efficiency = 100% – (L1 + L2 + L3 + ...)
where L1, L2, etc. are the individual losses as a percentage
of input power.
Although all dissipative elements in the circuit produce
losses, four main sources usually account for most of the
losses in LTC1709-7 circuits: 1) I2R losses, 2) Topside
MOSFET transition losses, 3) INTVCC regulator current
and 4) LTC1709-7 VIN current (including loading on the
differential amplifier output).
1) I2R losses are predicted from the DC resistances of the
fuse (if used), MOSFET, inductor, current sense resistor,
and input and output capacitor ESR. In continuous mode
the average output current flows through L and RSENSE,
but is “chopped” between the topside MOSFET and the
21
LTC1709-7
U
W
U
U
APPLICATIO S I FOR ATIO
synchronous MOSFET. If the two MOSFETs have approximately the same RDS(ON), then the resistance of one
MOSFET can simply be summed with the resistances of L,
RSENSE and ESR to obtain I2R losses. For example, if each
RDS(ON) = 10mΩ, RL = 10mΩ, and RSENSE = 5mΩ, then the
total resistance is 25mΩ. This results in losses ranging
from 2% to 8% as the output current increases from 3A to
15A per output stage for a 5V output, or a 3% to 12% loss
per output stage for a 3.3V output. Efficiency varies as the
inverse square of VOUT for the same external components
and output power level. The combined effects of increasingly lower output voltages and higher currents required
by high performance digital systems is not doubling but
quadrupling the importance of loss terms in the switching
regulator system!
2) Transition losses apply only to the topside MOSFET(s),
and are significant only when operating at high input
voltages (typically 12V or greater). Transition losses can
be estimated from:
Transition Loss = (1.7) VIN2 IO(MAX) CRSS f
3) INTVCC current is the sum of the MOSFET driver and
control currents. The MOSFET driver current results from
switching the gate capacitance of the power MOSFETs.
Each time a MOSFET gate is switched from low to high to
low again, a packet of charge dQ moves from INTVCC to
ground. The resulting dQ/dt is a current out of INTVCC that
is typically much larger than the control circuit current. In
continuous mode, IGATECHG = (QT + QB), where QT and QB
are the gate charges of the topside and bottom side
MOSFETs.
Supplying INTVCC power through the EXTVCC switch input
from an output-derived source will scale the VIN current
required for the driver and control circuits by the ratio
(Duty Factor)/(Efficiency). For example, in a 20V to 5V
application, 10mA of INTVCC current results in approximately 3mA of VIN current. This reduces the mid-current
loss from 10% or more (if the driver was powered directly
from VIN) to only a few percent.
4) The VIN current has two components: the first is the
DC supply current given in the Electrical Characteristics
table, which excludes MOSFET driver and control currents; the second is the current drawn from the differential
22
amplifier output. VIN current typically results in a small
(<0.1%) loss.
Other “hidden” losses such as copper trace and internal
battery resistances can account for an additional 5% to
10% efficiency degradation in portable systems. It is very
important to include these “system” level losses in the
design of a system. The internal battery and input fuse
resistance losses can be minimized by making sure that
CIN has adequate charge storage and a very low ESR at
the switching frequency. A 50W supply will typically
require a minimum of 200µF to 300µF of output capacitance having a maximum of 10mΩ to 20mΩ of ESR. The
LTC1709-7 2-phase architecture typically halves the
input and output capacitance requirements over competing solutions. Other losses including Schottky conduction losses during dead-time and inductor core losses
generally account for less than 2% total additional loss.
Checking Transient Response
The regulator loop response can be checked by looking at
the load transient response. Switching regulators take
several cycles to respond to a step in DC (resistive) load
current. When a load step occurs, VOUT shifts by an
amount equal to ∆ILOAD(ESR), where ESR is the effective
series resistance of COUT (∆ILOAD) also begins to charge or
discharge COUT generating the feedback error signal that
forces the regulator to adapt to the current change and
return VOUT to its steady-state value. During this recovery
time VOUT can be monitored for excessive overshoot or
ringing, which would indicate a stability problem. The
availability of the ITH pin not only allows optimization of
control loop behavior but also provides a DC coupled and
AC filtered closed loop response test point. The DC step,
rise time, and settling at this test point truly reflects the
closed loop response. Assuming a predominantly second
order system, phase margin and/or damping factor can be
estimated using the percentage of overshoot seen at this
pin. The bandwidth can also be estimated by examining
the rise time at the pin. The ITH external components
shown in the Figure 1 circuit will provide an adequate
starting point for most applications.
The ITH series RC-CC filter sets the dominant pole-zero
loop compensation. The values can be modified slightly
LTC1709-7
U
W
U
U
APPLICATIO S I FOR ATIO
(from 0.2 to 5 times their suggested values) to optimize
transient response once the final PC layout is done and the
particular output capacitor type and value have been
determined. The output capacitors need to be decided
upon first because the various types and values determine
the loop gain and phase. An output current pulse of 20%
to 80% of full-load current having a rise time of <2µs will
produce output voltage and ITH pin waveforms that will
give a sense of the overall loop stability without breaking
the feedback loop. The initial output voltage step resulting
from the step change in output current may not be within
the bandwidth of the feedback loop, so this signal cannot
be used to determine phase margin. This is why it is
better to look at the Ith pin signal which is in the feedback
loop and is the filtered and compensated control loop
response. The gain of the loop will be increased by
increasing RC and the bandwidth of the loop will be
increased by decreasing CC. If RC is increased by the
same factor that CC is decreased, the zero frequency will
be kept the same, thereby keeping the phase the same in
the most critical frequency range of the feedback loop.
The output voltage settling behavior is related to the
stability of the closed-loop system and will demonstrate
the actual overall supply performance.
tow truck operators finding that a 24V jump start cranks
cold engines faster than 12V.
Automotive Considerations: Plugging into the
Cigarette Lighter
Design Example
As battery-powered devices go mobile, there is a natural
interest in plugging into the cigarette lighter in order to
conserve or even recharge battery packs during operation. But before you connect, be advised: you are plugging
into the supply from hell. The main battery line in an
automobile is the source of a number of nasty potential
transients, including load-dump, reverse-battery, and
double-battery.
Load-dump is the result of a loose battery cable. When the
cable breaks connection, the field collapse in the alternator
can cause a positive spike as high as 60V which takes
several hundred milliseconds to decay. Reverse-battery is
just what it says, while double-battery is a consequence of
The network shown in Figure 9 is the most straightforward approach to protect a DC/DC converter from the
ravages of an automotive power line. The series diode
prevents current from flowing during reverse-battery,
while the transient suppressor clamps the input voltage
during load-dump. Note that the transient suppressor
should not conduct during double-battery operation, but
must still clamp the input voltage below breakdown of the
converter. Although the LT1709-7 has a maximum input
voltage of 36V, most applications will be limited to 30V by
the MOSFET BVDSS.
50A IPK RATING
12V
TRANSIENT VOLTAGE
SUPPRESSOR
GENERAL INSTRUMENT
1.5KA24A
VIN
LTC1709-7
17097 F09
Figure 9. Automotive Application Protection
As a design example, assume VIN = 5V (nominal), VIN␣ =␣ 5.5V
(max), VOUT = 1.8V, IMAX = 20A, TA = 70°C and f␣ =␣ 300kHz.
The inductance value is chosen first based on a 30% ripple
current assumption. The highest value of ripple current
occurs at the maximum input voltage. Tie the FREQSET pin
to the INTVCC pin for 300kHz operation. The minimum
inductance for 30% ripple current is:
L≥
≥
VOUT  VOUT 
 1−

f( ∆L) 
VIN 
1.8 V
 1.8 V 
 1−

(300kHz)(30%)(10A)  5.5V 
≥ 1.35µH
23
LTC1709-7
U
U
W
U
APPLICATIO S I FOR ATIO
A 1.5µH inductor will produce 27% ripple current. The
peak inductor current will be the maximum DC value plus
one half the ripple current, or 11.5A. The minimum ontime occurs at maximum VIN:
tON(MIN) =
VOUT
1.8 V
=
= 1.1µs
VIN f
5.5V 300kHz
( )(
)
The RSENSE resistors value can be calculated by using the
maximum current sense voltage specification with some
accomodation for tolerances:
RSENSE =
50mV
≈ 0.004Ω
11.5A
( ) [1+ (0.005)(110°C − 25°C)]
2
0.013Ω + 1.7(5.5V ) (10 A )(300pF )
(300kHz) = 0.65W
1.8 V
10
5.5V
2
The worst-case power disipated by the synchronous
MOSFET under normal operating conditions at elevated
ambient temperature and estimated 50°C junction temperature rise is:
( ) (1.48)(0.013Ω)
5.5V − 1.8 V
PSYNC =
10 A
5.5V
= 1.29W
2
A short-circuit to ground will result in a folded back current
of about:
( )

25mV
1  200ns 5.5V
ISC =
+
0.004Ω 2  1.5µH

24
( ) (1.48)(0.013Ω)
5.5V − 1.8 V
7A
5.5V
= 630mW
PSYNC =
2
which is less than normal, full-load conditions. Incidentally, since the load no longer dissipates power in the
shorted condition, total system power dissipation is decreased by over 99%.
The duty factor for this application is:
The power dissipation on the topside MOSFET can be
easily estimated. Using a Siliconix Si4420DY for example;
RDS(ON) = 0.013Ω, CRSS = 300pF. At maximum input
voltage with TJ (estimated) = 110°C at an elevated ambient
temperature:
PMAIN =
The worst-case power disipated by the synchronous
MOSFET under short-circuit conditions at elevated ambient temperature and estimated 50°C junction temperature
rise is:

 = 7A


DF =
VO 1.8 V
=
= 0.36
VIN
5V
Using Figure 4, the RMS ripple current will be:
IINRMS = (20A)(0.23) = 4.6ARMS
An input capacitor(s) with a 4.6ARMS ripple current rating
is required.
The output capacitor ripple current is calculated by using
the inductor ripple already calculated for each inductor
and multiplying by the factor obtained from Figure␣ 3
along with the calculated duty factor. The output ripple in
continuous mode will be highest at the maximum input
voltage since the duty factor is < 50%. The maximum
output current ripple is:
( )
VOUT
0.3 at 33% D F
fL
1.8 V
∆ICOUTMAX =
0.3
300kHz 1.5µH
∆ICOUT =
(
= 1.2ARMS
(
)(
)
)
VOUTRIPPLE = 20mΩ 1.2ARMS = 24mVRMS
LTC1709-7
U
W
U
U
APPLICATIO S I FOR ATIO
PC Board Layout Checklist
When laying out the printed circuit board, the following
checklist should be used to ensure proper operation of the
LTC1709-7. These items are also illustrated graphically in
the layout diagram of Figure␣ 12. Check the following in
your layout:
1) Are the signal and power grounds segregated? The
LTC1709-7 signal ground pin should return to the (–) plate
of COUT separately. The power ground returns to the
sources of the bottom N-channel MOSFETs, anodes of the
Schottky diodes, and (–) plates of CIN, which should have
as short lead lengths as possible.
2) Does the LTC1709-7 VOS+ pin connect to the point of
load? Does the LTC1709-7 VOS– pin connect to the load
return?
3) Are the SENSE – and SENSE + leads routed together with
minimum PC trace spacing? The filter capacitors between
SENSE + and SENSE – pin pairs should be as close as
possible to the LTC1709-7. Ensure accurate current sensing with Kelvin connections at the current sense resistor.
4) Does the (+) plate of CIN connect to the drains of the
topside MOSFETs as closely as possible? This capacitor
provides the AC current to the MOSFETs. Keep the input
current path formed by the input capacitor, top and bottom
MOSFETs, and the Schottky diode on the same side of the
PC board in a tight loop to minimize conducted and
radiated EMI.
5) Is the INTVCC 1µF ceramic decoupling capacitor connected closely between INTVCC and the power ground pin?
This capacitor carries the MOSFET driver peak currents. A
small value is recommended to allow placement immediately adjacent to the IC.
6) Keep the switching nodes, SW1 (SW2), away from
sensitive small-signal nodes. Ideally the switch nodes
should be placed at the furthest point from the
LTC1709-7.
7) Use a low impedance source such as a logic gate to drive
the PLLIN pin and keep the lead as short as possible.
The diagram in Figure 10 illustrates all branch currents in
a 2-phase switching regulator. It becomes very clear after
studying the current waveforms why it is critical to keep
the high-switching-current paths to a small physical size.
High electric and magnetic fields will radiate from these
“loops” just as radio stations transmit signals. The output
capacitor ground should return to the negative terminal of
the input capacitor and not share a common ground path
with any switched current paths. The left half of the circuit
gives rise to the “noise” generated by a switching regulator. The ground terminations of the sychronous MOSFETs
and Schottky diodes should return to the negative plate(s)
of the input capacitor(s) with a short isolated PC trace
since very high switched currents are present. A separate
isolated path from the negative plate(s) of the input
capacitor(s) should be used to tie in the IC power ground
pin (PGND) and the signal ground pin (SGND). This
technique keeps inherent signals generated by high current pulses from taking alternate current paths that have
finite impedances during the total period of the switching
regulator. External OPTI-LOOP compensation allows overcompensation for PC layouts which are not optimized but
this is not the recommended design procedure.
Simplified Visual Explanation of How a 2-Phase
Controller Reduces Both Input and Output RMS Ripple
Current
A multiphase power supply significantly reduces the
amount of ripple current in both the input and output
capacitors. The RMS input ripple current is divided by, and
the effective ripple frequency is multiplied up by the
number of phases used (assuming that the input voltage
is greater than the number of phases used times the output
voltage). The output ripple amplitude is also reduced by,
and the effective ripple frequency is increased by the
number of phases used. Figure 11 graphically illustrates
the principle.
The worst-case RMS ripple current for a single stage
design peaks at an input voltage of twice the output
voltage. The worst-case RMS ripple current for a two stage
design results in peak outputs of 1/4 and 3/4 of input
voltage. When the RMS current is calculated, higher
effective duty factor results and the peak current levels are
divided as long as the currents in each stage are balanced.
Refer to Application Note 19 for a detailed description of
25
LTC1709-7
U
U
W
U
APPLICATIO S I FOR ATIO
SW1
L1
RSENSE1
D1
VIN
VOUT
RIN
CIN
+
+
SW2
L2
COUT
RL
RSENSE2
D2
BOLD LINES INDICATE
HIGH, SWITCHING
CURRENT LINES.
KEEP LINES TO A
MINIMUM LENGTH.
17097 F10
Figure 10. Instantaneous Current Path Flow in a Multiple Phase Switching Regulator
SINGLE PHASE
SW V
DUAL PHASE
how to calculate RMS current for the single stage switching regulator. Figures 3 and 4 illustrate how the input and
output currents are reduced by using an additional phase.
The input current peaks drop in half and the frequency is
doubled for this 2-phase converter. The input capacity
requirement is thus reduced theoretically by a factor of
four! Ceramic input capacitors with their unbeatably low
ESR characteristics can be used.
SW1 V
SW2 V
ICIN
IL1
ICOUT
IL2
ICIN
ICOUT
RIPPLE
17097 F11
Figure 11. Single and 2-Phase Current Waveforms
26
Figure 4 illustrates the RMS input current drawn from the
input capacitance vs the duty cycle as determined by the
ratio of input and output voltage. The peak input RMS
current level of the single phase system is reduced by 50%
in a 2-phase solution due to the current splitting between
the two stages.
LTC1709-7
U
U
W
U
APPLICATIO S I FOR ATIO
An interesting result of the 2-phase solution is that the VIN
which produces worst-case ripple current for the input
capacitor, VOUT = VIN/2, in the single phase design produces zero input current ripple in the 2-phase design.
∆IRIPPLE =


where D is duty factor.
The output ripple current is reduced significantly when
compared to the single phase solution using the same
inductance value because the VOUT/L discharge current
term from the stage that has its bottom MOSFET on
subtracts current from the (VIN – VOUT)/L charging current
resulting from the stage which has its top MOSFET on. The
output ripple current is:
U
PACKAGE DESCRIPTIO
( ) 

2VOUT  1 − 2D 1 − D
fL  1 − 2D + 1

The input and output ripple frequency is increased by the
number of stages used, reducing the output capacity
requirements. When VIN is approximately equal to 2(VOUT)
as illustrated in Figures 3 and 4, very low input and output
ripple currents result.
Dimensions in inches (millimeters) unless otherwise noted.
G Package
36-Lead Plastic SSOP (0.209)
(LTC DWG # 05-08-1640)
12.67 – 12.93*
(0.499 – 0.509)
36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19
7.65 – 7.90
(0.301 – 0.311)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
5.20 – 5.38**
(0.205 – 0.212)
1.73 – 1.99
(0.068 – 0.078)
0° – 8°
0.13 – 0.22
(0.005 – 0.009)
0.55 – 0.95
(0.022 – 0.037)
NOTE: DIMENSIONS ARE IN MILLIMETERS
*DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.152mm (0.006") PER SIDE
**DIMENSIONS DO NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.254mm (0.010") PER SIDE
0.65
(0.0256)
BSC
0.25 – 0.38
(0.010 – 0.015)
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
0.05 – 0.21
(0.002 – 0.008)
G36 SSOP 1098
27
LTC1709-7
U
TYPICAL APPLICATIO
LTC1709-7
0.1µF
1000pF
2.7k
RUN/SS
NC
2
SENSE1 +
TG1
3
SENSE1 –
SW1
4
10k
INTVCC
6
51k
15k
INTVCC
47k
5
7
8
3.3nF
100pF
9
10
11
12
13
1000pF
14
15
470pF
16
17
18
EAIN
BOOST1
VIN
PLLFLTR
BG1
PLLIN
EXTVCC
FCB
INTVCC
ITH
SGND
PGND
VDIFFOUT
BG2
VOS –
BOOST2
VOS +
SW2
SENSE2 –
TG2
SENSE2 +
ATTENOUT
PGOOD
VBIAS
ATTENIN
VID4
VID0
VID3
VID1
VID2
36
L1
35
0.004Ω
34
0.22µF
33
M1
M2
32
D1
MBRS140T3
31
30
10Ω
5V (OPT)
CIN
47µF 35V
+
29
0.1µF
10µF
28
+
1
COUT
27
26
M3
0.22µF
25
VOUT
0.9V TO 2V
20A
0.004Ω
100k
23
L2
PGOOD
22
21
D2
MBRS140T3
M4
24
0.1µF
VIN
5V TO 28V
SWITCHING FREQUENCY = 200kHz
CIN: 5A RIPPLE CURRENT RATING REQUIRED
COUT: 4 × 180µF/4V PANASONIC SP
L1 TO L2: 1.5µH SUMIDA CEP125-1R5MC
M1 TO M4: FAIRCHILD FDS7760A
10Ω
20
19
VID INPUTS
17097 F12
Figure 12. 5V to 20V Input, 0.9V to 2V/20A Power Supply with Active Voltage Positioning
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LTC1438/LTC1439
Dual High Efficiency Low Noise Synchronous Step-Down Switching Regulators POR, Auxiliary Regulator
LTC1438-ADJ
Dual Synchronous Controller with Auxiliary Regulator
POR, External Feedback Divider
LTC1538-AUX
Dual High Efficiency Low Noise Synchronous Step-Down Switching Regulator
Auxiliary Regulator, 5V Standby
LTC1539
Dual High Efficiency Low Noise Synchronous Step-Down Switching Regulator
5V Standby, POR, Low-Battery, Aux Regulator
LTC1436A-PLL
High Efficiency Low Noise Synchronous Step-Down Switching Regulator
Adaptive PowerTM Mode, 24-Pin SSOP
LTC1628/LTC1628-PG Dual High Efficiency, 2-Phase Synchronous Step-Down Switching Regulator
Constant Frequency, Standby, 5V and 3.3V LDOs
LTC1629/LTC1629-PG PolyPhase High Efficiency Controller
Expandable Up to 12 Phases, G-28, Up to 120A
LTC1929/LTC1929-PG 2-Phase High Efficiency Controller
Adjustable Output Up to 40A, G-28
LTC1702/LTC1703
Dual High Efficiency, 2-Phase Synchronous Step-Down Switching Regulator
500kHz, 25MHz GBW
LTC1708-PG
Dual High Efficiency, 2-Phase Synchronous Step-Down Switching Regulator
with 5-Bit VID and Power Good Indication
1.3V ≤ VOUT ≤ 3.5V, Current Mode Ensures
Accurate Current Sharing, 3.5V ≤ VIN ≤ 36V
LTC1709-8/LTC1709-9 2-Phase High Efficiency Controller with 5-Bit VID and Power Good
VID Tables VRM 8.4 and VRM9.0
LTC1735
High Efficiency Synchronous Step-Down Controller
Burst Mode Operation, 16-Pin Narrow SSOP,
Fault Protection, 3.5V ≤ VIN ≤ 36V
LTC1736
High Efficiency Synchronous Step-Down Controller with 5-Bit VID
Output Fault Protection, Power Good, GN-24,
3.5V ≤ VIN ≤ 36V, 0.925V ≤ VOUT ≤ 2V
Adaptive Power is a trademark of Linear Technology Corporation.
28
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408)432-1900 ● FAX: (408) 434-0507 ● www.linear-tech.com
17097f LT/TP 0600 4K • PRINTED IN USA
 LINEAR TECHNOLOGY CORPORATION 2000