LINER LTC3729_1

LTC3729
550kHz, PolyPhase,
High Efficiency, Synchronous
Step-Down Switching Regulator
DESCRIPTION
FEATURES
Wide VIN Range: 4V to 36V Operation
n Reduces Required Input Capacitance and Power
Supply Induced Noise
n ±1% Output Voltage Accuracy
n Phase-Lockable Fixed Frequency: 250kHz to 550kHz
n True Remote Sensing Differential Amplifier
nPolyPhase® Extends from Two to Twelve Phases
n Reduces the Size and Value of Inductors
n Current Mode Control Ensures Current Sharing
n 1.1MHz Effective Switching Frequency (2-Phase)
nOPTI-LOOP® Compensation Reduces C
OUT
n Power Good Output Voltage Indicator
n Very Low Dropout Operation: 99% Duty Cycle
n Adjustable Soft-Start Current Ramping
n Internal Current Foldback Plus Shutdown Timer
n Overvoltage Soft-Latch Eliminates Nuisance Trips
n Available in 5mm × 5mm QFN
and 28-Lead SSOP Packages
n
APPLICATIONS
Desktop Computers/Servers
Large Memory Arrays
n DC Power Distribution Systems
n
n
L, LT, LTC, LTM, PolyPhase, OPTI-LOOP, Linear Technology and the Linear logo are registered
trademarks of Linear Technology Corporation. All other trademarks are the property of their
respective owners.
The LTC ®3729 is a multiple phase, synchronous
step‑down current mode switching regulator controller
that drives N‑channel external power MOSFET stages in a
phase‑lockable fixed frequency architecture. The PolyPhase
controller drives its two output stages out of phase at
frequencies up to 550kHz to minimize the RMS ripple
currents in both input and output capacitors. The output
clock signal allows expansion for up to 12 evenly phased
controllers for systems requiring 15A to 200A of output
current. The multiple phase technique effectively multiplies
the fundamental frequency by the number of channels
used, improving transient response while operating each
channel at an optimum frequency for efficiency. Thermal
design is also simplified.
An internal differential amplifier provides true remote sens‑
ing of the regulated supply’s positive and negative output
terminals as required for high current applications.
A RUN/SS pin provides both soft-start and optional timed,
short-circuit shutdown. Current foldback limits MOSFET
dissipation during short-circuit conditions when the
overcurrent latchoff is disabled. OPTI-LOOP compensation
allows the transient response to be optimized over a wide
range of output capacitance and ESR values. The LTC3729
includes a power good output pin that indicates when the
output is within ±7.5% of the designed set point.
TYPICAL APPLICATION
0.1µF
LTC3729
VIN
TG1
PGOOD
ITH
VDIFFOUT
16k
–
VOS
VOS+
M3
S
BOOST2
SW2
EAIN
L1
D1 0.8µH
VIN
5V TO 28V
SENSE1+
16k
S
M2
×2
S
BG1
PGND
TG2
SGND
0.002Ω
0.47µF
SENSE1–
1000pF
S
S
SW1
RUN/SS
10µF
35V
CERAMIC
×4
M1
BOOST1
0.1µF
3.3k
10Ω
S
S
BG2
INTVCC
+
SENSE2
0.002Ω
0.47µF
S
+
S
M4
×2
D2
10µF
+
SENSE2–
COUT: T510E108K004AS
D1, D2: UP5840
L1, L2: CEPH149-IROMC
VOUT
1.6V/40A
L2
0.8µH
M1, M3: IRF7811W
M2, M4: IRF7822
Figure 1. High Current Dual Phase Step-Down Converter
COUT
1000µF ×2
4V
3729 TA01
3729fb
1
LTC3729
ABSOLUTE MAXIMUM RATINGS
(Note 1)
Input Supply Voltage (VIN).......................... 36V to –0.3V
Topside Driver Voltages (BOOST1,2).......... 42V to –0.3V
Switch Voltage (SW1, 2)............................... 36V to –5 V
SENSE1+, SENSE2+, SENSE1–,
SENSE2– Voltages ..........................(1.1)INTVCC to –0.3V
EAIN, VOS+, VOS–, EXTVCC, INTVCC,
RUN/SS, PGOOD Voltages ........................... 7V to –0.3V
Boosted Driver Voltage (BOOST-SW)............ 7V to –0.3V
PLLFLTR, PLLIN, CLKOUT, PHASMD,
VDIFFOUT Voltages ...............INTVCC to –0.3V for VIN ≥ 7V
VDIFFOUT Voltages..............VIN – 2V to –0.3V for VIN < 7V
ITH Voltage ................................................ 2.7V to –0.3V
Peak Output Current <1µs(TGL1,2, BG1,2)..................5A
INTVCC RMS Output Current.................................. 50mA
Operating Ambient Temperature
Range (Note 6).......................................... –40°C to 85°C
Junction Temperature (Note 2).............................. 125°C
Storage Temperature Range.................... –65°C to 150°C
Lead Temperature (Soldering, 10 sec)
(G Package Only)............................................... 300°C
PIN CONFIGURATION
TOP VIEW
PLLFLTR
5
24 VIN
32 31 30 29 28 27 26 25
24 BOOST1
23 VIN
22 BG1
PLLIN 3
6
PHASMD
7
22 EXTVCC
ITH
8
21 INTVCC
SGND
9
20 PGND
23 BG1
PHASMD 4
21 EXTVCC
ITH 5
20 INTVCC
SGND 6
19 PGND
VDIFFOUT 7
NC
SW2
TG2
15 PGOOD
PGOOD
16 TG2
SENSE2+
SENSE2+
SENSE2– 13
9 10 11 12 13 14 15 16
SENSE2
17 SW2
–
VOS+ 12
17 BOOST2
VOS+
18 BOOST2
18 BG2
VOS– 8
NC
19 BG2
VOS– 11
14
EAIN 1
PLLFLTR 2
PLLIN
VDIFFOUT 10
SW1
25 BOOST1
TG1
4
CLKOUT
26 SW1
EAIN
RUN/SS
27 TG1
3
NC
2
SENSE1–
SENSE1+
SENSE1+
NC
RUN/SS
28 CLKOUT
SENSE1–
TOP VIEW
1
UH PACKAGE
32-LEAD 5mm × 5mm PLASTIC QFN
θJA = 34°C/W
EXPOSED PAD IS GND, MUST BE SOLDERED TO PCB
G PACKAGE
28-LEAD PLASTIC SSOP
TJMAX = 125°C, θJA = 95°C/W
ORDER INFORMATION
LEAD FREE FINISH
TAPE AND REEL
PART MARKING
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LTC3729EG#PBF
LTC3729EG#TRPBF
LTC3729
28-Lead Plastic SSOP
–40°C to 85°C
LTC3729EUH#PBF
LTC3729EUH#TRPBF
3729
32-Lead (5mm × 5mm)Plastic QFN
–40°C to 85°C
Consult LTC Marketing for parts specified with wider operating temperature ranges.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
3729fb
2
LTC3729
ELECTRICAL
CHARACTERISTICS
The
l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VIN = 15V, VRUN/SS = 5V unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
l
0.792
0.800
0.808
V
l
62
65
75
75
88
85
mV
mV
–5
–50
nA
0.1
–0.1
0.5
–0.5
%
%
0.002
0.02
%/V
0.84
0.86
0.88
V
3
3.5
4
V
Main Control Loop
VEAIN
Regulated Feedback Voltage
(Note 3); ITH Voltage = 1.2V
– = 5V
VSENSEMAX
Maximum Current Sense Threshold
VSENSE
VSENSE1, 2 = 5V
IINEAIN
Feedback Current
(Note 3)
VLOADREG
Output Voltage Load Regulation
(Note 3)
Measured in Servo Loop; ITH Voltage = 0.7V
Measured in Servo Loop; ITH Voltage = 2V
VREFLNREG
Reference Voltage Line Regulation
VIN = 3.6V to 30V (Note 3)
VOVL
Output Overvoltage Threshold
Measured at VEAIN
UVLO
Undervoltage Lockout
VIN Ramping Down
l
l
l
gm
Transconductance Amplifier gm
ITH = 1.2V; Sink/Source 5µA; (Note 3)
3
mmho
gmOL
Transconductance Amplifier Gain
ITH = 1.2V; (gmxZL; No Ext Load); (Note 3)
1.5
V/mV
IQ
Input DC Supply Current
Normal Mode
Shutdown
(Note 4)
EXTVCC Tied to VOUT ; VOUT = 5V
VRUN/SS = 0V
580
20
40
µA
µA
IRUN/SS
Soft-Start Charge Current
VRUN/SS = 1.9V
–0.5
–1.2
VRUN/SS
RUN/SS Pin ON Threshold
VRUN/SS Rising
1.0
1.5
1.9
V
VRUN/SSLO
RUN/SS Pin Latchoff Arming
VRUN/SS Rising from 3V
3.8
4.5
V
0.5
µA
ISCL
RUN/SS Discharge Current
Soft Short Condition VEAIN = 0.5V; VRUN/SS = 4.5V
ISDLDO
Shutdown Latch Disable Current
VEAIN = 0.5V
2
4
µA
1.6
5
µA
ISENSE
Total Sense Pins Source Current
Each Channel; VSENSE1–, 2– = VSENSE1+, 2+ = 0V
–85
–60
µA
DFMAX
Maximum Duty Factor
In Dropout
98
99.5
%
TG1, 2 tr
TG1, 2 tf
Top Gate Transition Time:
Rise Time
Fall Time
CLOAD = 3300pF
CLOAD = 3300pF
30
40
90
90
ns
ns
BG1, 2 tr
BG1, 2 tf
Bottom Gate Transition Time:
Rise Time
Fall Time
CLOAD = 3300pF
CLOAD = 3300pF
30
20
90
90
ns
ns
TG/BG t1D
Top Gate Off to Bottom Gate On Delay
CLOAD = 3300pF Each Driver
Synchronous Switch-On Delay Time
BG/TG t2D
Bottom Gate Off to Top Gate On Delay
CLOAD = 3300pF Each Driver
Top Switch-On Delay Time
90
ns
tON(MIN)
Minimum On-Time
100
ns
90
Tested with a Square Wave (Note 5)
ns
Internal VCC Regulator
VINTVCC
Internal VCC Voltage
6V < VIN < 30V; VEXTVCC = 4V
VLDO INT
INTVCC Load Regulation
ICC = 0 to 20mA; VEXTVCC = 4V
VLDO EXT
EXTVCC Voltage Drop
ICC = 20mA; VEXTVCC = 5V
VEXTVCC
EXTVCC Switchover Voltage
ICC = 20mA, EXTVCC Ramping Positive
VLDOHYS
EXTVCC Switchover Hysteresis
ICC = 20mA, EXTVCC Ramping Negative
4.8
l
4.5
5.0
5.2
V
0.2
1.0
%
80
160
mV
4.7
V
0.2
V
Oscillator and Phase-Locked Loop
fNOM
Nominal Frequency
VPLLFLTR = 1.2V
360
400
440
kHz
fLOW
Lowest Frequency
VPLLFLTR = 0V
230
260
290
kHz
fHIGH
Highest Frequency
VPLLFLTR ≥ 2.4V
480
550
590
kHz
RPLLIN
PLLIN Input Resistance
50
kΩ
3729fb
3
LTC3729
ELECTRICAL
CHARACTERISTICS
The
l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VIN = 15V, VRUN/SS = 5V unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
IPLLFLTR
Phase Detector Output Current
Sinking Capability
Sourcing Capability
fPLLIN < fOSC
fPLLIN > fOSC
–15
15
µA
µA
RRELPHS
Controller 2-Controller 1 Phase
VPHASMD = 0V, Open
VPHASMD = 5V
180
240
Deg
Deg
CLKOUT
Phase (Relative to Controller 1)
VPHASMD = 0V
VPHASMD = Open
VPHASMD = 5V
60
90
120
Deg
Deg
Deg
CLKHIGH
Clock High Output Voltage
CLKLOW
Clock Low Output Voltage
4
UNITS
V
0.2
V
0.3
V
±1
µA
PGOOD Output
VPGL
PGOOD Voltage Low
IPGOOD = 2mA
0.1
IPGOOD
PGOOD Leakage Current
VPGOOD = 5V
VPG
PGOOD Trip Level, Either Controller
VEAIN with Respect to Set Output Voltage
VEAIN Ramping Negative
VEAIN Ramping Positive
–6
6
–7.5
7.5
–9.5
9.5
%
%
0.995
1
1.005
V/V
46
55
dB
80
kΩ
Differential
Amplifier
ADA
Gain
CMRRDA
Common Mode Rejection Ratio
0V < VCM < 5V
RIN
Input Resistance
Measured at VOS+ Input
Note 1: Absolute Maximum Ratings are those values beyond which
the life of a device may be impaired.
Note 2: TJ is calculated from the ambient temperature TA and power
dissipation PD according to the following formulas:
LTC3729EG: TJ = TA + (PD • 95°C/W)
LTC3729EUH: TJ = TA + (PD • 34°C/W)
Note 3: The LTC3729 is tested in a feedback loop that servos VITH to a
specified voltage and measures the resultant VEAIN.
Note 4: Dynamic supply current is higher due to the gate charge being
delivered at the switching frequency. See Applications Information.
Note 5: The minimum on-time condition corresponds to the on inductor
peak-to-peak ripple current ≥40% of IMAX (see Minimum On-Time
Considerations in the Applications Information section).
Note 6: The LTC3729E is guaranteed to meet performance specifications
from 0°C to 70°C. Specifications over the –40°C to 85°C operating
temperature range are assured by design, characterization and correlation
with statistical process controls.
3729fb
4
LTC3729
TYPICAL PERFORMANCE CHARACTERISTICS
Efficiency vs Output Current
(Figure 12)
Efficiency vs Output Current
(Figure 12)
100
VIN = 12V
VIN = 20V
40
VOUT = 3.3V
VEXTVCC = 5V
IOUT = 20A
f = 250kHz
20
0.1
1
10
OUTPUT CURRENT (A)
VEXTVCC = 0V
EFFICIENCY (%)
VIN = 8V
60
80
70
50
VOUT = 3.3V
f = 250kHz
10
OUTPUT CURRENT (A)
1
1000
200
SHUTDOWN
5
20
15
10
25
INPUT VOLTAGE (V)
30
5.05
200
150
100
50
0
35
0
10
30
20
CURRENT (mA)
40
4.85
4.80
EXTVCC SWITCHOVER THRESHOLD
4.75
50
25
75
0
TEMPERATURE (°C)
100
125
3729 G06
Maximum Current Sense Threshold
vs Percent of Nominal Output
Voltage (Foldback)
75
ILOAD = 1mA
80
70
60
4.8
4.7
50
VSENSE (mV)
4.9
VSENSE (mV)
INTVCC VOLTAGE (V)
4.90
4.70
–50 –25
50
5.0
25
4.6
50
40
30
20
4.5
4.4
4.95
Maximum Current Sense Threshold
vs Duty Factor
Internal 5V LDO Line Reg
INTVCC VOLTAGE
5.00
3729 G05
3729 G04
5.1
20
INTVCC and EXTVCC Switch
Voltage vs Temperature
INTVCC AND EXTVCC SWITCH VOLTAGE (V)
EXTVCC VOLTAGE DROP (mV)
SUPPLY CURRENT (µA)
400
15
3729 G03
250
ON
10
VIN (V)
EXTVCC Voltage Drop
600
5
3729 G02
Supply Current vs Input Voltage
and Mode
0
80
70
100
3729 G01
0
90
60
100
800
VOUT = 3.3V
VEXTVCC = 5V
IOUT = 20A
f = 250kHz
VEXTVCC = 5V
90
VIN = 5V
EFFICIENCY (%)
EFFICIENCY (%)
100
100
80
0
Efficiency vs Input Voltage
(Figure 12)
10
0
5
20
15
25
10
INPUT VOLTAGE (V)
30
35
3729 G07
0
0
20
40
60
DUTY FACTOR (%)
80
100
3729 G08
0
50
100
0
25
75
PERCENT ON NOMINAL OUTPUT VOLTAGE (%)
3729 G09
3729fb
5
LTC3729
TYPICAL PERFORMANCE CHARACTERISTICS
Maximum Current Sense Threshold
vs Sense Common Mode Voltage
80
VSENSE(CM) = 1.6V
Current Sense Threshold
vs ITH Voltage
80
70
76
VSENSE (mV)
60
VSENSE (mV)
90
40
60
VSENSE (mV)
80
Maximum Current Sense Threshold
vs VRUN/SS (Soft-Start)
72
68
50
40
30
20
10
20
0
64
–10
–20
0
0
1
2
3
4
5
60
6
1
3
4
2
COMMON MODE VOLTAGE (V)
0
VRUN/SS (V)
Load Regulation
FCB = 0V
VIN = 15V
FIGURE 1
–0.3
–0.4
VITH vs VRUN/SS
1
3
2
LOAD CURRENT (A)
4
1
1.5
VITH (V)
2
5
SENSE Pins Total Source Current
VOSENSE = 0.7V
50
ISENSE (µA)
1.5
1.0
0
2.5
100
0
–50
0.5
0
0.5
3729 G12
2.0
–0.1
VITH (V)
NORMALIZED VOUT (%)
2.5
–0.2
0
3729 G11
3729 G10
0.0
–30
5
0
1
2
3
4
5
6
VRUN/SS (V)
–100
2
0
4
6
VSENSE COMMON MODE VOLTAGE (V)
3729 G14
3729 G13
Maximum Current Sense
Threshold vs Temperature
3729 G15
RUN/SS Current vs Temperature
80
1.8
1.6
RUN/SS CURRENT (µA)
VSENSE (mV)
78
76
74
72
1.4
1.2
1.0
0.8
0.6
0.4
0.2
70
–50
–25
50
25
0
75
TEMPERATURE (°C)
100
125
3729 G17
0
–50
–25
0
25
50
75
TEMPERATURE (°C)
100
125
3729 G19
3729fb
6
LTC3729
TYPICAL PERFORMANCE CHARACTERISTICS
Soft-Start Up (Figure 12)
Load Step (Figure 12)
VITH
1V/DIV
IOUT
0/30A
VITH
1V/DIV
VOUT
2V/DIV
VOUT
200mV/DIV
VRUNSS
2V/DIV
100ms/DIV
Current Sense Pin Input Current
vs Temperature
EXTVCC Switch Resistance
vs Temperature
31
29
27
–25
50
25
0
75
TEMPERATURE (°C)
100
125
600
8
6
4
2
0
–50
–25
50
25
0
75
TEMPERATURE (°C)
100
3729 G23
500
VPLLFLTR = 1.2V
400
300
VPLLFLTR = 0V
200
125
0
–50 –25
50
25
75
0
TEMPERATURE (°C)
3729 G24
Undervoltage Lockout
vs Temperature
100
125
3729 G25
Shutdown Latch Thresholds
vs Temperature
4.5
3.50
3.45
3.40
3.35
3.30
3.25
3.20
–50 –25
VPLLFLTR = 2.4V
100
SHUTDOWN LATCH THRESHOLDS (V)
25
–50
700
FREQUENCY (kHz)
EXTVCC SWITCH RESISTANCE (Ω)
33
3729 G21
Oscillator Frequency
vs Temperature
10
VOUT = 5V
UNDERVOLTAGE LOCKOUT (V)
CURRENT SENSE INPUT CURRENT (µA)
35
10µs/DIV
3729 G20
50
25
75
0
TEMPERATURE (°C)
100
125
3729 G26
LATCH ARMING
4.0
3.5
3.0
LATCHOFF
THRESHOLD
2.5
2.0
1.5
1.0
0.5
0
–50
–25
0
25
50
75
TEMPERATURE (°C)
100
125
3729 G27
3729fb
7
LTC3729
PIN FUNCTIONS
G Package/UH Package
RUN/SS (Pin 1/Pin 28): Combination of Soft-Start, Run
Control Input and Short-Circuit Detection Timer. A capaci‑
tor to ground at this pin sets the ramp time to full current
output. Forcing this pin below 0.8V causes the IC to shut
down all internal circuitry. All functions are disabled in
shutdown.
SENSE1+, SENSE2+ (Pins 2,14/Pins 30, 12): The (+)
Input to the Differential Current Comparators. The ITH
pin voltage and built-in offsets between SENSE– and
SENSE+ pins in conjunction with RSENSE set the current
trip threshold.
SENSE1–, SENSE2– (Pins 3, 13/Pins 31, 11): The (–)
Input to the Differential Current Comparators.
EAIN (Pin 4/Pin 1): Input to the Error Amplifier that com‑
pares the feedback voltage to the internal 0.8V reference
voltage. This pin is normally connected to a resistive divider
from the output of the differential amplifier (DIFFOUT).
PLLFLTR (Pin 5/Pin 2): The Phase-Locked Loop’s Low
Pass Filter is tied to this pin. Alternatively, this pin can
be driven with an AC or DC voltage source to vary the
frequency of the internal oscillator.
PLLIN (Pin 6/Pin 3): External Synchronization Input to
Phase Detector. This pin is internally terminated to SGND
with 50kΩ. The phase-locked loop will force the rising
top gate signal of controller 1 to be synchronized with
the rising edge of the PLLIN signal.
PHASMD (Pin 7/Pin 4): Control Input to Phase Selector
which determines the phase relationships between control‑
ler 1, controller 2 and the CLKOUT signal.
ITH (Pin 8/Pin 5): Error Amplifier Output and Switching
Regulator Compensation Point. Both current comparator’s
thresholds increase with this control voltage. The normal
voltage range of this pin is from 0V to 2.4V.
SGND (Pin 9/Pin 6): Signal Ground, common to both con‑
trollers, must be routed separately from the input switched
current ground path to the common (–) terminal(s) of the
COUT capacitor(s).
VDIFFOUT (Pin 10/Pin 7): Output of a Differential Amplifier
that provides true remote output voltage sensing. This pin
normally drives an external resistive divider that sets the
output voltage.
VOS–, VOS+ (Pins 11, 12/Pins 8, 9): Inputs to an Operational
Amplifier. Internal precision resistors capable of being
electronically switched in or out can configure it as a dif‑
ferential amplifier or an uncommitted Op Amp.
PGOOD (Pin 15/Pin 13): Open-Drain Logic Output. PGOOD
is pulled to ground when the voltage on the EAIN pin is
not within ±7.5% of its set point.
TG2, TG1 (Pins 16, 27/Pins 14, 26): High Current Gate
Drives for Top N-Channel MOSFETS. These are the outputs
of floating drivers with a voltage swing equal to INTVCC
superimposed on the switch node voltage SW.
SW2, SW1 (Pins 17, 26/Pins 15, 25): Switch Node
Connections to Inductors. Voltage swing at these pins
is from a Schottky diode (external) voltage drop below
ground to VIN.
BOOST2, BOOST1 (Pins 18, 25/Pins 17, 24): Bootstrapped
Supplies to the Topside Floating Drivers. Capacitors
are connected between the Boost and Switch pins and
Schottky diodes are tied between the Boost and INTVCC
pins. Voltage swing at the Boost pins is from INTVCC to
(VIN + INTVCC).
BG2, BG1 (Pins 19, 23/Pins 18, 22): High Current Gate
Drives for Bottom Synchronous N-Channel MOSFETS.
Voltage swing at these pins is from ground to INTVCC.
PGND (Pin 20/Pin 19): Driver Power Ground. Connect
to sources of bottom N-channel MOSFETS and the (–)
terminals of CIN.
INTVCC (Pin 21/Pin 20): Output of the Internal 5V Linear
Low Dropout Regulator and the EXTVCC Switch. The driver
and control circuits are powered from this voltage source.
Decouple to power ground with a 1µF ceramic capacitor
placed directly adjacent to the IC and minimum of 4.7µF
additional tantalum or other low ESR capacitor.
3729fb
8
LTC3729
PIN FUNCTIONS
G Package/UH Package
EXTVCC (Pin 22/Pin 21): External Power Input to an
Internal Switch . This switch closes and supplies INTVCC,
bypassing the internal low dropout regulator whenever
EXTVCC is higher than 4.7V. See EXTVCC Connection in
the Applications Information section. Do not exceed 7V
on this pin and ensure VEXTVCC ≤ VINTVCC.
VIN (Pin 24/Pin 23): Main Supply Pin. Should be closely
decoupled to the IC’s signal ground pin.
CLKOUT (Pin 28/Pin 27): Output Clock Signal available
to daisychain other controller ICs for additional MOSFET
driver stages/phases.
FUNCTIONAL DIAGRAM
PLLIN
INTVCC
PHASE DET
FIN
50k
DUPLICATE FOR SECOND
CONTROLLER CHANNEL
PLLLPF
RLP
CLKOUT
CLP
OSCILLATOR
DROP
OUT
DET
CLK2
PHASMD
±2µA
PHASE LOGIC
S
Q
R
Q
BOT
FCB
SW
FORCE BOT
SWITCH
LOGIC
INTVCC
BG
BOT
SHDN
A1
INTVCC
I1
+
40k
+
–
0.86V
SLOPE
COMP
EAIN
–
+
0.80V
–
+
30k SENSE
+
0.86V
4(VFB)
+
VIN
–
30k
45k
EAIN
0.74V
–
EA
+
VREF
–
5V
LDO
REG
0.80V
R2
0.86V
ITH
CC
1.2µA
6V
INTERNAL
SUPPLY
R1
+
–
INTVCC
+
COUT
VOUT
2.4V
OV
+
RSENSE
SENSE–
45k
VIN
4.7V
L
+
PGOOD
SGND
CIN
40k
–
40k
5V
+
PGND
40k
VOS+
EXTVCC
CB
TG
TOP
DIFFOUT
VOS–
DB
BOOST
CLK1
VIN
SHDN
RST
4(VFB)
RUN
SOFT
START
RC
RUN/SS
CSS
3729 FBD
3729fb
9
LTC3729
OPERATION
(Refer to Functional Diagram)
Main Control Loop
Low Current Operation
The LTC3729 uses a constant frequency, current mode
step-down architecture. During normal operation, the
top MOSFET is turned on each cycle when the oscillator
sets the RS latch, and turned off when the main current
comparator, I1, resets the RS latch. The peak inductor
current at which I1 resets the RS latch is controlled by
the voltage on the ITH pin, which is the output of the error
amplifier EA. The differential amplifier, A1, produces a
signal equal to the differential voltage sensed across the
output capacitor but re-references it to the internal signal
ground (SGND) reference. The EAIN pin receives a portion
of this voltage feedback signal at the DIFFOUT pin which is
compared to the internal reference voltage by the EA. When
the load current increases, it causes a slight decrease in
the EAIN pin voltage relative to the 0.8V reference, which
in turn causes the ITH voltage to increase until the average
inductor current matches the new load current. After the
top MOSFET has turned off, the bottom MOSFET is turned
on for the rest of the period.
The LTC3729 operates in a continuous, PWM control mode.
The resulting operation at low output currents optimizes
transient response at the expense of substantial negative
inductor current during the latter part of the period. The level
of ripple current is determined by the inductor value, input
voltage, output voltage, and frequency of operation.
The top MOSFET drivers are biased from floating bootstrap
capacitor CB, which normally is recharged during each
off cycle through an external Schottky diode. When VIN
decreases to a voltage close to VOUT , however, the loop
may enter dropout and attempt to turn on the top MOSFET
continuously. A dropout detector detects this condition and
forces the top MOSFET to turn off for about 400ns every
10th cycle to recharge the bootstrap capacitor.
The main control loop is shut down by pulling Pin 1
(RUN/SS) low. Releasing RUN/SS allows an internal 1.2µA
current source to charge soft-start capacitor CSS. When
CSS reaches 1.5V, the main control loop is enabled with the
ITH voltage clamped at approximately 30% of its maximum
value. As CSS continues to charge, ITH is gradually released
allowing normal operation to resume. When the RUN/SS
pin is low, all LTC3729 functions are shut down. If VOUT
has not reached 70% of its nominal value when CSS has
charged to 4.1V, an overcurrent latchoff can be invoked as
described in the Applications Information section.
Frequency Synchronization
The phase-locked loop allows the internal oscillator to be
synchronized to an external source via the PLLIN pin. The
output of the phase detector at the PLLFLTR pin is also the
DC frequency control input of the oscillator that operates over
a 250kHz to 550kHz range corresponding to a DC voltage
input from 0V to 2.4V. When locked, the PLL aligns the turn
on of the top MOSFET to the rising edge of the synchronizing
signal. When PLLIN is left open, the PLLFLTR pin goes low,
forcing the oscillator to minimum frequency.
The internal master oscillator runs at a frequency twelve
times that of each controller’s frequency. The PHASMD
pin determines the relative phases between the internal
controllers as well as the CLKOUT signal as shown in
Table 1. The phases tabulated are relative to zero phase
being defined as the rising edge of the top gate (TG1)
driver output of controller 1.
Table 1.
VPHASMD
GND
OPEN
INTVCC
Controller 2
180°
180°
240°
CLKOUT
60°
90°
120°
The CLKOUT signal can be used to synchronize additional
power stages in a multiphase power supply solution feeding
a single, high current output or separate outputs. Input
capacitance ESR requirements and efficiency losses are
substantially reduced because the peak current drawn from
the input capacitor is effectively divided by the number
of phases used and power loss is proportional to the
RMS current squared. A two stage, single output voltage
implementation can reduce input path power loss by 75%
and radically reduce the required RMS current rating of
the input capacitor(s).
3729fb
10
LTC3729
OPERATION
(Refer to Functional Diagram)
INTVCC/EXTVCC Power
Power for the top and bottom MOSFET drivers and most of
the IC circuitry is derived from INTVCC. When the EXTVCC
pin is left open, an internal 5V low dropout regulator
supplies INTVCC power. If the EXTVCC pin is taken above
4.7V, the 5V regulator is turned off and an internal switch
is turned on connecting EXTVCC to INTVCC. This allows
the INTVCC power to be derived from a high efficiency
external source such as the output of the regulator itself
or a secondary winding, as described in the Applications
Information section. An external Schottky diode can be
used to minimize the voltage drop from EXTVCC to INTVCC
in applications requiring greater than the specified INTVCC
current. Voltages up to 7V can be applied to EXTVCC for
additional gate drive capability.
Differential Amplifier
This amplifier provides true differential output voltage
sensing. Sensing both VOUT+ and VOUT– benefits regulation
in high current applications and/or applications having
electrical interconnection losses.
Power Good (PGOOD)
The PGOOD pin is connected to the drain of an internal
MOSFET. The MOSFET turns on when the output is not
within ±7.5% of its nominal output level as determined by
the feedback divider. When the output is within ±7.5% of
its nominal value, the MOSFET is turned off within 10µs
and the PGOOD pin should be pulled up by an external
resistor to a source of up to 7V.
Short-Circuit Detection
The RUN/SS capacitor is used initially to limit the inrush
current from the input power source. Once the controllers
have been given time, as determined by the capacitor on
the RUN/SS pin, to charge up the output capacitors and
provide full load current, the RUN/SS capacitor is then
used as a short-circuit timeout circuit. If the output volt‑
age falls to less than 70% of its nominal output voltage
the RUN/SS capacitor begins discharging assuming that
the output is in a severe overcurrent and/or short-circuit
condition. If the condition lasts for a long enough period
as determined by the size of the RUN/SS capacitor, the
controller will be shut down until the RUN/SS pin voltage
is recycled. This built-in latchoff can be overidden by
providing a >5µA pull-up current at a compliance of 5V
to the RUN/SS pin. This current shortens the soft-start
period but also prevents net discharge of the RUN/SS
capacitor during a severe overcurrent and/or short-circuit
condition. Foldback current limiting is activated when the
output voltage falls below 70% of its nominal level whether
or not the short-circuit latchoff circuit is enabled.
APPLICATIONS INFORMATION
The basic LTC3729 application circuit is shown in Figure 1
on the first page. External component selection is driven
by the load requirement, and begins with the selection
of RSENSE1, 2. Once RSENSE1, 2 are known, L1 and L2 can
be chosen. Next, the power MOSFETs and D1 and D2 are
selected. The operating frequency and the inductor are
chosen based mainly on the amount of ripple current.
Finally, CIN is selected for its ability to handle the input
ripple current (that PolyPhase operation minimizes) and
COUT is chosen with low enough ESR to meet the output
ripple voltage and load step specifications (also minimized
with PolyPhase). The circuit shown in Figure 1 can be
configured for operation up to an input voltage of 28V
(limited by the external MOSFETs).
RSENSE Selection For Output Current
RSENSE1, 2 are chosen based on the required output cur‑
rent. The LTC3729 current comparator has a maximum
threshold of 75mV/RSENSE and an input common mode
range of SGND to 1.1( INTVCC). The current comparator
threshold sets the peak inductor current, yielding a maxi‑
mum average output current IMAX equal to the peak value
less half the peak-to-peak ripple current, ∆IL.
Allowing a margin for variations in the LTC3729 and external
component values yields:
RSENSE = (50mV/IMAX)N
where N = number of stages.
3729fb
11
LTC3729
APPLICATIONS INFORMATION
When using the controller in very low dropout conditions,
the maximum output current level will be reduced due to
internal slope compensation required to meet stability
criterion for buck regulators operating at greater than 50%
duty factor. A curve is provided to estimate this reduction
in peak output current level depending upon the operating
duty factor.
Operating Frequency
The LTC3729 uses a constant frequency, phase-lockable
architecture with the frequency determined by an internal
capacitor. This capacitor is charged by a fixed current plus
an additional current which is proportional to the voltage
applied to the PLLFLTR pin. Refer to Phase-Locked Loop
and Frequency Synchronization in the Applications Infor‑
mation section for additional information.
A graph for the voltage applied to the PLLFLTR pin vs
frequency is given in Figure 2. As the operating frequency
is increased the gate charge losses will be higher, reducing
efficiency (see Efficiency Considerations). The maximum
switching frequency is approximately 550kHz.
PLLFLTR PIN VOLTAGE (V)
2.5
2.0
1.5
1.0
0.5
0
200
250 300 350 400 450 500
OPERATING FREQUENCY (kHz)
550
3729 F02
Figure 2. Operating Frequency vs VPLLFLTR
Inductor Value Calculation and Output Ripple Current
The operating frequency and inductor selection are inter‑
related in that higher operating frequencies allow the use
of smaller inductor and capacitor values. So why would
anyone ever choose to operate at lower frequencies with
larger components? The answer is efficiency. A higher
frequency generally results in lower efficiency because
of MOSFET gate charge and transition losses. In addi‑
tion to this basic tradeoff, the effect of inductor value on
ripple current and low current operation must also be
considered. The PolyPhase approach reduces both input
and output ripple currents while optimizing individual
output stages to run at a lower fundamental frequency,
enhancing efficiency.
The inductor value has a direct effect on ripple current.
The inductor ripple current ∆IL per individual section,
N, decreases with higher inductance or frequency and
increases with higher VIN or VOUT :
∆IL =
VOUT  VOUT 
1−
fL 
VIN 
where f is the individual output stage operating frequency.
In a PolyPhase converter, the net ripple current seen by
the output capacitor is much smaller than the individual
inductor ripple currents due to the ripple cancellation. The
details on how to calculate the net output ripple current
can be found in Application Note 77.
Figure 3 shows the net ripple current seen by the output
capacitors for the different phase configurations. The output
ripple current is plotted for a fixed output voltage as the
duty factor is varied between 10% and 90% on the x-axis.
The output ripple current is normalized against the inductor
ripple current at zero duty factor. The graph can be used
in place of tedious calculations. As shown in Figure 3, the
zero output ripple current is obtained when:
VOUT k
=
VIN N
where k = 1, 2, …, N – 1
So the number of phases used can be selected to minimize
the output ripple current and therefore the output ripple
voltage at the given input and output voltages. In appli‑
cations having a highly varying input voltage, additional
phases will produce the best results.
3729fb
12
LTC3729
APPLICATIONS INFORMATION
1.0
0.8
0.7
0.6
VO/fL
∆IO(P-P)
ripple current and consequent output voltage ripple. Do
not allow the core to saturate!
1-PHASE
2-PHASE
3-PHASE
4-PHASE
6-PHASE
0.9
0.5
0.4
0.3
0.2
0.1
0
0.1
0.2
0.3 0.4 0.5 0.6 0.7
DUTY FACTOR (VOUT/VIN)
0.8
0.9
3729 F03
Figure 3. Normalized Peak Output Current vs
Duty Factor [IRMS ≈ 0.3 (∆IO(P–P))]
Accepting larger values of ∆IL allows the use of low in‑
ductances, but can result in higher output voltage ripple.
A reasonable starting point for setting ripple current is
∆IL = 0.4(IOUT)/N, where N is the number of channels and
IOUT is the total load current. Remember, the maximum
∆IL occurs at the maximum input voltage. The individual
inductor ripple currents are constant determined by the
inductor, input and output voltages.
Inductor Core Selection
Once the values for L1 and L2 are known, the type of
inductor must be selected. High efficiency converters
generally cannot afford the core loss found in low cost
powdered iron cores, forcing the use of more expensive
ferrite, molypermalloy, or Kool Mµ® cores. Actual core loss
is independent of core size for a fixed inductor value, but it
is very dependent on inductance selected. As inductance
increases, core losses go down. Unfortunately, increased
inductance requires more turns of wire and therefore cop‑
per losses will increase.
Ferrite designs have very low core loss and are preferred
at high switching frequencies, so design goals can con‑
centrate on copper loss and preventing saturation. Ferrite
core material saturates “hard,” which means that induc‑
tance collapses abruptly when the peak design current is
exceeded. This results in an abrupt increase in inductor
Molypermalloy (from Magnetics, Inc.) is a very good, low
loss core material for toroids, but it is more expensive
than ferrite. A reasonable compromise from the same
manufacturer is Kool Mµ. Toroids are very space effi‑
cient, especially when you can use several layers of wire.
Because they lack a bobbin, mounting is more difficult.
However, designs for surface mount are available which
do not increase the height significantly.
Power MOSFET, D1 and D2 Selection
Two external power MOSFETs must be selected for each
controller with the LTC3729: One N-channel MOSFET for
the top (main) switch, and one N-channel MOSFET for the
bottom (synchronous) switch.
The peak-to-peak drive levels are set by the INTVCC voltage.
This voltage is typically 5V during start-up (see EXTVCC Pin
Connection). Consequently, logic-level threshold MOSFETs
must be used in most applications. The only exception
is if low input voltage is expected (VIN < 5V); then, sub‑
logic-level threshold MOSFETs (VGS(TH) < 3V) should be
used. Pay close attention to the BVDSS specification for
the MOSFETs as well; most of the logic-level MOSFETs
are limited to 30V or less.
Selection criteria for the power MOSFETs include the
“ON” resistance RDS(ON), reverse transfer capacitance
CRSS, input voltage, and maximum output current. When
the LTC3729 is operating in continuous mode the duty
factors for the top and bottom MOSFETs of each output
stage are given by:
V
Main Switch Duty Cycle = OUT
VIN
 V –V 
Synchronous Switch Duty Cycle =  IN OUT 
VIN


The MOSFET power dissipations at maximum output
current are given by:
Kool Mµ is a registered trademark of Magnetics, Inc.
3729fb
13
LTC3729
APPLICATIONS INFORMATION
V –V
I

PSYNC = IN OUT  MAX 
 N 
VIN
2
(1+ d )RDS(ON)
where d is the temperature dependency of RDS(ON), k is a
constant inversely related to the gate drive current and N
is the number of stages.
Both MOSFETs have I2R losses but the topside N-channel
equation includes an additional term for transition losses,
which peak at the highest input voltage. For VIN < 20V
the high current efficiency generally improves with larger
MOSFETs, while for VIN > 20V the transition losses rapidly
increase to the point that the use of a higher RDS(ON) device
with lower CRSS actual provides higher efficiency. The
synchronous MOSFET losses are greatest at high input
voltage when the top switch duty factor is low or during
a short-circuit when the synchronous switch is on close
to 100% of the period.
The term (1 + d) is generally given for a MOSFET in the
form of a normalized RDS(ON) vs. Temperature curve,
but d = 0.005/°C can be used as an approximation for
low voltage MOSFETs. CRSS is usually specified in the
MOSFET characteristics. The constant k = 1.7 can be used
to estimate the contributions of the two terms in the main
switch dissipation equation.
The Schottky diodes, D1 and D2 shown in Figure 1 conduct
during the dead-time between the conduction of the two large
power MOSFETs. This helps prevent the body diode of the
bottom MOSFET from turning on, storing charge during the
dead-time, and requiring a reverse recovery period which
would reduce efficiency. A 1A to 3A (depending on output
current) Schottky diode is generally a good compromise for
both regions of operation due to the relatively small average
current. Larger diodes result in additional transition losses
due to their larger junction capacitance.
CIN and COUT Selection
In continuous mode, the source current of each top
N‑channel MOSFET is a square wave of duty cycle
VOUT/VIN. A low ESR input capacitor sized for the maximum
RMS current must be used. The details of a close form
equation can be found in Application Note 77. Figure 4
shows the input capacitor ripple current for different phase
configurations with the output voltage fixed and input volt‑
age varied. The input ripple current is normalized against
the DC output current. The graph can be used in place of
tedious calculations. The minimum input ripple current
can be achieved when the product of phase number and
output voltage, N(VOUT), is approximately equal to the
input voltage VIN or:
VOUT k
=
VIN N
where k = 1, 2, …, N – 1
So the phase number can be chosen to minimize the input
capacitor size for the given input and output voltages.
In the graph of Figure 4, the local maximum input RMS
capacitor currents are reached when:
VOUT 2k − 1
=
VIN
2N
where k = 1, 2, …, N
0.6
0.5
DC LOAD CURRENT
(1+ d )RDS(ON) +

2I
k ( VIN )  MAX  (CRSS ) ( f )
 N 
2
RMS INPUT RIPPLE CURRNET
V
I

PMAIN = OUT  MAX 
VIN  N 
1-PHASE
2-PHASE
3-PHASE
4-PHASE
6-PHASE
0.4
0.3
0.2
0.1
0
0.1
0.2
0.3 0.4 0.5 0.6 0.7
DUTY FACTOR (VOUT/VIN)
0.8
0.9
3729 F04
Figure 4. Normalized Input RMS Ripple Current vs
Duty Factor for 1 to 6 Output Stages
These worst-case conditions are commonly used for
design because even significant deviations do not offer
much relief. Note that capacitor manufacturer’s ripple
current ratings are often based on only 2000 hours of life.
3729fb
14
LTC3729
APPLICATIONS INFORMATION
This makes it advisable to further derate the capacitor, or
to choose a capacitor rated at a higher temperature than
required. Several capacitors may also be paralleled to meet
size or height requirements in the design. Always consult
the capacitor manufacturer if there is any question.
The graph shows that the peak RMS input current is
reduced linearly, inversely proportional to the number, N
of stages used. It is important to note that the efficiency
loss is proportional to the input RMS current squared
and therefore a 2-stage implementation results in 75%
less power loss when compared to a single phase design.
Battery/input protection fuse resistance (if used), PC board
trace and connector resistance losses are also reduced by
the reduction of the input ripple current in a PolyPhase
system. The required amount of input capacitance is further
reduced by the factor, N, due to the effective increase in
the frequency of the current pulses.
The selection of COUT is driven by the required effective
series resistance (ESR). Typically once the ESR require‑
ment has been met, the RMS current rating generally far
exceeds the IRIPPLE(P-P) requirements. The steady state
output ripple (∆VOUT) is determined by:

1 
∆VOUT ≈ ∆IRIPPLE  ESR +
8NfCOUT 

Where f = operating frequency of each stage, N is the
number of phases, COUT = output capacitance, and
∆IRIPPLE = combined inductor ripple currents.
The output ripple varies with input voltage since ∆IL is a
function of input voltage. The output ripple will be less than
50mV at max VIN with ∆IL = 0.4IOUT(MAX)/N assuming:
COUT required ESR < 2N(RSENSE) and
COUT > 1/(8Nf)(RSENSE)
The emergence of very low ESR capacitors in small,
surface mount packages makes very physically small
implementations possible. The ability to externally
compensate the switching regulator loop using the
ITH pin(OPTI-LOOP compensation) allows a much
wider selection of output capacitor types. OPTI-LOOP
compensation effectively removes constraints on output
capacitor ESR. The impedance characteristics of each
capacitor type are significantly different than an ideal
capacitor and therefore require accurate modeling or
bench evaluation during design.
Manufacturers such as Nichicon, United Chemicon and
Sanyo should be considered for high performance throughhole capacitors. The OS-CON semiconductor dielectric
capacitor available from Sanyo and the Panasonic SP
surface mount types have the lowest (ESR)(size) product
of any aluminum electrolytic at a somewhat higher price.
An additional ceramic capacitor in parallel with OS-CON
type capacitors is recommended to reduce the inductance
effects.
In surface mount applications, multiple capacitors may
have to be paralleled to meet the ESR or RMS current
handling requirements of the application. Aluminum
electrolytic and dry tantalum capacitors are both available
in surface mount configurations. New special polymer
surface mount capacitors offer very low ESR also but
have much lower capacitive density per unit volume. In
the case of tantalum, it is critical that the capacitors are
surge tested for use in switching power supplies. Several
excellent choices are the AVX TPS, AVX TPSV or the KEMET
T510 series of surface mount tantalums, available in case
heights ranging from 2mm to 4mm. Other capacitor types
include Sanyo OS-CON, Nichicon PL series and Sprague
595D series. Consult the manufacturer for other specific
recommendations. A combination of capacitors will often
result in maximizing performance and minimizing overall
cost and size.
INTVCC Regulator
An internal P-channel low dropout regulator produces
5V at the INTVCC pin from the VIN supply pin. The INTVCC
regulator powers the drivers and internal circuitry of the
LTC3729. The INTVCC pin regulator can supply up to
50mA peak and must be bypassed to power ground with
a minimum of 4.7µF tantalum or electrolytic capacitor. An
additional 1µF ceramic capacitor placed very close to the IC
is recommended due to the extremely high instantaneous
currents required by the MOSFET gate drivers.
High input voltage applications in which large MOSFETs
are being driven at high frequencies may cause the
3729fb
15
LTC3729
APPLICATIONS INFORMATION
maximum junction temperature rating for the LTC3729 to
be exceeded. The supply current is dominated by the gate
charge supply current, in addition to the current drawn
from the differential amplifier output. The gate charge is
dependent on operating frequency as discussed in the
Efficiency Considerations section. The supply current can
either be supplied by the internal 5V regulator or via the
EXTVCC pin. When the voltage applied to the EXTVCC pin
is less than 4.7V, all of the INTVCC load current is supplied
by the internal 5V linear regulator. Power dissipation for
the IC is higher in this case by (IIN)(VIN – INTVCC) and
efficiency is lowered. The junction temperature can be
estimated by using the equations given in Note 1 of the
Electrical Characteristics. For example, the LTC3729 VIN
current is limited to less than 24mA from a 24V supply:
TJ = 70°C + (24mA)(24V)(95°C/W) = 125°C
Use of the EXTVCC pin reduces the junction temperature
to:
TJ = 70°C + (24mA)(5V)(95°C/W) = 81.4°C
The input supply current should be measured while
the controller is operating in continuous mode at maximum
VIN and the power dissipation calculated in order to
prevent the maximum junction temperature from being
exceeded.
EXTVCC Connection
The LTC3729 contains an internal P-channel MOSFET
switch connected between the EXTVCC and INTVCC pins.
When the voltage applied to EXTVCC rises above 4.7V,
the internal regulator is turned off and the switch closes,
connecting the EXTVCC pin to the INTVCC pin thereby
supplying internal and MOSFET gate driving power. The
switch remains closed as long as the voltage applied to
EXTVCC remains above 4.5V. This allows the MOSFET
driver and control power to be derived from the output
during normal operation (4.7V < VEXTVCC < 7V) and from
the internal regulator when the output is out of regulation
(start-up, short-circuit). Do not apply greater than 7V
to the EXTVCC pin and ensure that EXTVCC < VIN + 0.3V
when using the application circuits shown. If an external
voltage source is applied to the EXTVCC pin when the VIN
supply is not present, a diode can be placed in series
with the LTC3729’s VIN pin and a Schottky diode between
the EXTVCC and the VIN pin, to prevent current from
backfeeding VIN.
Significant efficiency gains can be realized by powering
INTVCC from the output, since the VIN current resulting
from the driver and control currents will be scaled by the
ratio: (Duty Factor)/(Efficiency). For 5V regulators this
means connecting the EXTVCC pin directly to VOUT .
However, for 3.3V and other lower voltage regulators,
additional circuitry is required to derive INTVCC power
from the output.
The following list summarizes the four possible connec‑
tions for EXTVCC:
1. EXTVCC left open (or grounded). This will cause INTVCC
to be powered from the internal 5V regulator resulting in
a significant efficiency penalty at high input voltages.
2. EXTVCC connected directly to VOUT. This is the normal
connection for a 5V regulator and provides the highest
efficiency.
3. EXTVCC connected to an external supply. If an external
supply is available in the 5V to 7V range, it may be used to
power EXTVCC providing it is compatible with the MOSFET
gate drive requirements. VIN must be greater than or equal
to the voltage applied to the EXTVCC pin.
4. EXTVCC connected to an output-derived boost network.
For 3.3V and other low voltage regulators, efficiency gains
can still be realized by connecting EXTVCC to an outputderived voltage which has been boosted to greater than
4.7V but less than 7V. This can be done with either the
inductive boost winding as shown in Figure 5a or the
capacitive charge pump shown in Figure 5b. The charge
pump has the advantage of simple magnetics.
Topside MOSFET Driver Supply (CB,DB) (Refer to
Functional Diagram)
External bootstrap capacitors CB1 and CB2 connected
to the BOOST1 and BOOST2 pins supply the gate drive
voltages for the topside MOSFETs. Capacitor CB in the
Functional Diagram is charged though diode DB from
INTVCC when the SW pin is low. When the topside MOSFET
turns on, the driver places the CB voltage across the
3729fb
16
LTC3729
APPLICATIONS INFORMATION
OPTIONAL EXTVCC CONNECTION
5V < VSEC < 7V
+
CIN
LTC3729
VIN
CIN
VIN
LTC3729
1N4148
EXTVCC
+
6.8V
N-CH
T1
BG1
BAT85
N-CH
1mF
+
0.22µF
1µF
BAT85
VOUT
SW1
COUT
BG1
BAT85
VN2222LL
EXTVCC
RSENSE
SW1
VIN
+
VIN
TG1
VSEC
TG1
+
RSENSE
L1
VOUT
+
COUT
N-CH
N-CH
PGND
PGND
3729 F05b
3729 F05a
Figure 5a. Secondary Output Loop and EXTVCC Connection
gate-source of the desired MOSFET. This enhances the
MOSFET and turns on the topside switch. The switch node
voltage, SW, rises to VIN and the BOOST pin rises to VIN +
VINTVCC. The value of the boost capacitor CB needs to be
30 to 100 times that of the total input capacitance of the
topside MOSFET(s). The reverse breakdown of DB must
be greater than VIN(MAX).
The final arbiter when defining the best gate drive amplitude
level will be the input supply current. If a change is made
that decreases input current, the efficiency has improved.
If the input current does not change then the efficiency
has not changed either.
Differential Amplifier/Output Voltage
The LTC3729 has a true remote voltage sense capablity.
The sensing connections should be returned from the load
back to the differential amplifier’s inputs through a common,
tightly coupled pair of PC traces. The differential amplifier
rejects common mode signals capacitively or inductively
radiated into the feedback PC traces as well as ground
loop disturbances. The differential amplifier output signal
is divided down and compared with the internal precision
0.8V voltage reference by the error amplifier.
The differential amplifier utilizes a set of internal preci‑
sion resistors to enable precision instrumentation-type
measurement of the output voltage. The output is an NPN
emitter follower without any internal pull-down current.
A DC resistive load to ground is required in order to sink
Figure 5b. Capacitive Charge Pump for EXTVCC
current. The output voltage is set by an external resistive
divider according to the following formula:
 R1
VOUT = 0.8V  1+ 
 R2 
where R1 and R2 are defined in the Functional Diagram.
Soft-Start/Run Function
The RUN/SS pin provides three functions: 1) Run/Shut‑
down, 2) soft-start and 3) a defeatable short-circuit latchoff
timer. Soft-start reduces the input power sources’ surge
currents by gradually increasing the controller’s current
limit ITH(MAX). The latchoff timer prevents very short, ex‑
treme load transients from tripping the overcurrent latch.
A small pull-up current (>5µA) supplied to the RUN/SS
pin will prevent the overcurrent latch from operating.
The following explanation describes how the functions
operate.
An internal 1.2µA current source charges up the CSS
capacitor. When the voltage on RUN/SS reaches 1.5V, the
controller is permitted to start operating. As the voltage on
RUN/SS increases from 1.5V to 3.0V, the internal current
limit is increased from 25mV/RSENSE to 75mV/RSENSE.
The output current limit ramps up slowly, taking an ad‑
ditional 1.4µs/µF to reach full current. The output current
thus ramps up slowly, reducing the starting surge current
required from the input power supply. If RUN/SS has been
3729fb
17
LTC3729
APPLICATIONS INFORMATION
pulled all the way to ground there is a delay before starting
of approximately:
1.5V
t DELAY =
C = (1.25s / µF ) CSS
1.2µA SS
VIN
3.3V OR 5V
D1
INTVCC
RUN/SS
RSS*
RSS*
D1*
The time for the output current to ramp up is then:
t RAMP =
3V − 1.5V
C = (1.25s / µF ) CSS
1.2µA SS
By pulling the RUN/SS pin below 0.8V the LTC3729 is
put into low current shutdown (IQ < 40µA). RUN/SS can
be driven directly from logic as shown in Figure 6. Diode
D1 in Figure 6 reduces the start delay but allows CSS to
ramp up slowly providing the soft-start function. The
RUN/SS pin has an internal 6V zener clamp (see Functional
Diagram).
Fault Conditions: Overcurrent Latchoff
The RUN/SS pin also provides the ability to latch off the
controllers when an overcurrent condition is detected.
The RUN/SS capacitor, CSS, is used initially to limit the
inrush current of both controllers. After the controllers
have been started and been given adequate time to charge
up the output capacitors and provide full load current, the
RUN/SS capacitor is used for a short-circuit timer. If the
output voltage falls to less than 70% of its nominal value
after CSS reaches 4.1V, CSS begins discharging on the as‑
sumption that the output is in an overcurrent condition. If
the condition lasts for a long enough period as determined
by the size of CSS, the controller will be shut down until
the RUN/SS pin voltage is recycled. If the overload occurs
during start-up, the time can be approximated by:
tLO1 ≈ (CSS • 0.6V)/(1.2µA) = 5 • 105 (CSS)
If the overload occurs after start-up, the voltage on CSS
will continue charging and will provide additional time
before latching off:
tLO2 ≈ (CSS • 3V)/(1.2µA) = 2.5 • 106 (CSS)
This built-in overcurrent latchoff can be overridden by
providing a pull-up resistor, RSS, to the RUN/SS pin as
shown in Figure 6. This resistance shortens the softstart period and prevents the discharge of the RUN/SS
capacitor during a severe overcurrent and/or short-circuit
RUN/SS
CSS
CSS
*OPTIONAL TO DEFEAT OVERCURRENT LATCHOFF
3729 F06
Figure 6. RUN/SS Pin Interfacing
condition. When deriving the 5µA current from VIN as
in the figure, current latchoff is always defeated. Diodeconnecting this pull-up resistor to INTVCC, as in Figure 6,
eliminates any extra supply current during shutdown
while eliminating the INTVCC loading from preventing
controller start-up.
Why should you defeat current latchoff? During the pro‑
totyping stage of a design, there may be a problem with
noise pickup or poor layout causing the protection circuit
to latch off the controller. Defeating this feature allows
troubleshooting of the circuit and PC layout. The internal
short-circuit and foldback current limiting still remains
active, thereby protecting the power supply system from
failure. A decision can be made after the design is com‑
plete whether to rely solely on foldback current limiting
or to enable the latchoff feature by removing the pull-up
resistor.
The value of the soft-start capacitor CSS may need to
be scaled with output voltage, output capacitance and
load current characteristics. The minimum soft-start
capacitance is given by:
CSS > (COUT )(VOUT)(10-4)(RSENSE)
The minimum recommended soft-start capacitor of CSS =
0.1µF will be sufficient for most applications.
Phase-Locked Loop and Frequency Synchronization
The LTC3729 has a phase-locked loop comprised of an
internal voltage controlled oscillator and phase detector.
This allows the top MOSFET turn-on to be locked to the
rising edge of an external source. The frequency range
of the voltage controlled oscillator is ±50% around the
center frequency fO. A voltage applied to the PLLFLTR
pin of 1.2V corresponds to a frequency of approximately
3729fb
18
LTC3729
APPLICATIONS INFORMATION
400kHz. The nominal operating frequency range of the
LTC3729 is 250kHz to 550kHz.
The phase detector used is an edge sensitive digital type
which provides zero degrees phase shift between the ex‑
ternal and internal oscillators. This type of phase detector
will not lock up on input frequencies close to the harmonics
of the VCO center frequency. The PLL hold-in range, ∆fH,
is equal to the capture range, ∆fC:
∆fH = ∆fC = ±0.5 fO (250kHz-550kHz)
The output of the phase detector is a complementary pair of
current sources charging or discharging the external filter
network on the PLLFLTR pin. A simplified block diagram
is shown in Figure 7.
2.4V
PHASE
DETECTOR
EXTERNAL
OSC
RLP
10k
CLP
PLLFLTR
PLLIN
50k
DIGITAL
PHASE/
FREQUENCY
DETECTOR
a voltage that will guarantee the slave oscillator(s) ability
to lock onto the master’s frequency. A DC voltage of
0.7V to 1.7V applied to the master oscillator’s PLLFLTR
pin is recommended in order to meet this requirement.
The resultant operating frequency will be approximately
500kHz.
The loop filter components (CLP, RLP) smooth out the cur‑
rent pulses from the phase detector and provide a stable
input to the voltage controlled oscillator. The filter compo‑
nents CLP and RLP determine how fast the loop acquires
lock. Typically RLP =10k and CLP is 0.01µF to 0.1µF.
Minimum On-Time Considerations
Minimum on-time tON(MIN) is the smallest time duration
that the LTC3729 is capable of turning on the top MOSFET.
It is determined by internal timing delays and the gate
charge required to turn on the top MOSFET. Low duty
cycle applications may approach this minimum on-time
limit and care should be taken to ensure that:
OSC
3729 F07
Figure 7. Phase-Locked Loop Block Diagram
If the external frequency (fPLLIN) is greater than the os‑
cillator frequency f0SC, current is sourced continuously,
pulling up the PLLFLTR pin. When the external frequency is
less than f0SC, current is sunk continuously, pulling down
the PLLFLTR pin. If the external and internal frequencies
are the same but exhibit a phase difference, the current
sources turn on for an amount of time corresponding to
the phase difference. Thus the voltage on the PLLFLTR
pin is adjusted until the phase and frequency of the ex‑
ternal and internal oscillators are identical. At this stable
operating point the phase comparator output is open and
the filter capacitor CLP holds the voltage. The LTC3729
PLLIN pin must be driven from a low impedance source
such as a logic gate located close to the pin. When us‑
ing multiple LTC3729’s for a phase-locked system, the
PLLFLTR pin of the master oscillator should be biased at
t ON(MIN ) <
VOUT
VIN ( f )
If the duty cycle falls below what can be accommodated
by the minimum on-time, the LTC3729 will begin to skip
cycles resulting in nonconstant frequency operation. The
output voltage will continue to be regulated, but the ripple
current and ripple voltage will increase.
The minimum on-time for the LTC3729 is approximately
100ns. However, as the peak sense voltage decreases
the minimum on-time gradually increases. This is of
particular concern in forced continuous applications with
low ripple current at light loads. If the duty cycle drops
below the minimum on-time limit in this situation, a
significant amount of cycle skipping can occur with cor‑
respondingly larger current and voltage ripple.
If an application can operate close to the minimum on-time
limit, an inductor must be chosen that has a low enough
inductance to provide sufficient ripple amplitude to meet
the minimum on-time requirement. As a general rule,
keep the inductor ripple current of each phase equal to or
greater than 15% of IOUT(MAX)/N at VIN(MAX).
3729fb
19
LTC3729
APPLICATIONS INFORMATION
Voltage Positioning
Voltage positioning can be used to minimize peak-to-peak
output voltage excursions under worst-case transient
loading conditions. The open-loop DC gain of the control
loop is reduced depending upon the maximum load step
specifications. Voltage positioning can easily be added to
the LTC3729 by loading the ITH pin with a resistive divider
having a Thevenin equivalent voltage source equal to the
midpoint operating voltage range of the error amplifier, or
1.2V (see Figure 8).
2) INTVCC regulator current, 3) I2R losses and 4) Topside
MOSFET transition losses.
1) The VIN current has two components: the first is the
DC supply current given in the Electrical Characteristics
table, which excludes MOSFET driver and control currents;
the second is the current drawn from the differential
amplifier output. VIN current typically results in a small
(<0.1%) loss.
Figure 8. Active Voltage Positioning Applied to the LTC3729
2) INTVCC current is the sum of the MOSFET driver and
control currents. The MOSFET driver current results from
switching the gate capacitance of the power MOSFETs.
Each time a MOSFET gate is switched from low to high
to low again, a packet of charge dQ moves from INTVCC
to ground. The resulting dQ/dt is a current out of INTVCC
that is typically much larger than the control circuit cur‑
rent. In continuous mode, IGATECHG = (QT + QB), where
QT and QB are the gate charges of the topside and bottom
side MOSFETs.
The resistive load reduces the DC loop gain while main‑
taining the linear control range of the error amplifier.
The maximum output voltage deviation can theoretically
be reduced to half or alternatively the amount of output
capacitance can be reduced for a particular application.
A complete explanation is included in Design Solutions
10. (See www.linear-tech.com)
Supplying INTVCC power through the EXTVCC switch input
from an output-derived source will scale the VIN current
required for the driver and control circuits by the ratio (Duty
Factor)/(Efficiency). For example, in a 20V to 5V application,
10mA of INTVCC current results in approximately 3mA of
VIN current. This reduces the mid-current loss from 10%
or more (if the driver was powered directly from VIN) to
only a few percent.
INTVCC
RT2
ITH
RT1
RC
LTC3729
CC
3729 F08
Efficiency Considerations
The percent efficiency of a switching regulator is equal to
the output power divided by the input power times 100%.
It is often useful to analyze individual losses to determine
what is limiting the efficiency and which change would
produce the most improvement. Percent efficiency can
be expressed as:
%Efficiency = 100% – (L1 + L2 + L3 + ...)
where L1, L2, etc. are the individual losses as a percent‑
age of input power.
Although all dissipative elements in the circuit produce
losses, four main sources usually account for most of
the losses in LTC3729 circuits: 1) LTC3729 VIN current
(including loading on the differential amplifier output),
3) I2R losses are predicted from the DC resistances of the
fuse (if used), MOSFET, inductor, current sense resistor,
and input and output capacitor ESR. In continuous
mode the average output current flows through L and
RSENSE, but is “chopped” between the topside MOSFET
and the synchronous MOSFET. If the two MOSFETs have
approximately the same RDS(ON), then the resistance of
one MOSFET can simply be summed with the resistances
of L, RSENSE and ESR to obtain I2R losses. For example,
if each RDS(ON)=10mΩ, RL=10mΩ, and RSENSE=5mΩ,
then the total resistance is 25mΩ. This results in losses
ranging from 2% to 8% as the output current increases
from 3A to 15A per output stage for a 5V output, or a 3%
to 12% loss per output stage for a 3.3V output. Efficiency
varies as the inverse square of VOUT for the same external
components and output power level. The combined effects
3729fb
20
LTC3729
APPLICATIONS INFORMATION
of increasingly lower output voltages and higher currents
required by high performance digital systems is not
doubling but quadrupling the importance of loss terms
in the switching regulator system!
4) Transition losses apply only to the topside MOSFET(s),
and only when operating at high input voltages (typically
20V or greater). Transition losses can be estimated from:
Transition Loss = (1.7) VIN2 IO(MAX) CRSS f
Other “hidden” losses such as copper trace and internal
battery resistances can account for an additional 5% to
10% efficiency degradation in portable systems. It is very
important to include these “system” level losses in the
design of a system. The internal battery and input fuse
resistance losses can be minimized by making sure that
CIN has adequate charge storage and a very low ESR at the
switching frequency. A 50W supply will typically require
a minimum of 200µF to 300µF of capacitance having
a maximum of 10mΩ to 20mΩ of ESR. The LTC3729
PolyPhase architecture typically halves to quarters this
input capacitance requirement over competing solutions.
Other losses including Schottky conduction losses during
dead-time and inductor core losses generally account for
less than 2% total additional loss.
Checking Transient Response
The regulator loop response can be checked by look‑
ing at the load transient response. Switching regulators
take several cycles to respond to a step in DC (resistive)
load current. When a load step occurs, VOUT shifts by an
amount equal to ∆ILOAD(ESR), where ESR is the effective
series resistance of COUT(∆ILOAD) also begins to charge or
discharge COUT generating the feedback error signal that
forces the regulator to adapt to the current change and
return VOUT to its steady-state value. During this recovery
time VOUT can be monitored for excessive overshoot or
ringing, which would indicate a stability problem. The
availability of the ITH pin not only allows optimization of
control loop behavior but also provides a DC coupled and
AC filtered closed loop response test point. The DC step,
rise time, and settling at this test point truly reflects the
closed loop response. Assuming a predominantly second
order system, phase margin and/or damping factor can be
estimated using the percentage of overshoot seen at this
pin. The bandwidth can also be estimated by examining the
rise time at the pin. The ITH external components shown
in the Figure 1 circuit will provide an adequate starting
point for most applications.
The ITH series RC-CC filter sets the dominant pole-zero
loop compensation. The values can be modified slightly
(from 0.2 to 5 times their suggested values) to maximize
transient response once the final PC layout is done and
the particular output capacitor type and value have been
determined. The output capacitors need to be decided upon
because the various types and values determine the loop
feedback factor gain and phase. An output current pulse
of 20% to 80% of full-load current having a rise time of
<2µs will produce output voltage and ITH pin waveforms
that will give a sense of the overall loop stability without
breaking the feedback loop. The initial output voltage step
resulting from the step change in output current may not
be within the bandwidth of the feedback loop, so this
signal cannot be used to determine phase margin. This
is why it is better to look at the Ith pin signal which is in
the feedback loop and is the filtered and compensated
control loop response. The gain of the loop will be in‑
creased by increasing RC and the bandwidth of the loop
will be increased by decreasing CC. If RC is increased by
the same factor that CC is decreased, the zero frequency
will be kept the same, thereby keeping the phase shift the
same in the most critical frequency range of the feedback
loop. The output voltage settling behavior is related to the
stability of the closed-loop system and will demonstrate
the actual overall supply performance.
A second, more severe transient is caused by switching
in loads with large (>1µF) supply bypass capacitors. The
discharged bypass capacitors are effectively put in parallel
with COUT , causing a rapid drop in VOUT . No regulator can
alter its delivery of current quickly enough to prevent this
sudden step change in output voltage if the load switch
resistance is low and it is driven quickly. If the ratio of
CLOAD to COUT is greater than1:50, the switch rise time
should be controlled so that the load rise time is limited
to approximately 25 • CLOAD. Thus a 10µF capacitor would
require a 250µs rise time, limiting the charging current
to about 200mA.
3729fb
21
LTC3729
APPLICATIONS INFORMATION
Design Example (Using Two Phases)
As a design example, assume VIN = 5V (nominal), VIN = 5.5V
(max), VOUT = 1.8V, IMAX = 20A, TA = 70°C and f = 300kHz.
The inductance value is chosen first based on a 30% ripple
current assumption. The highest value of ripple current
occurs at the maximum input voltage. Tie the PLLFLTR
pin to a resistive divider using the INTVCC pin to generate
1V for 300kHz operation. The minimum inductance for
30% ripple current is:
L≥
VOUT  VOUT 
1−
f ( ∆I) 
VIN 
1.8V
 1.8V 
1−
≥
(300kHz )(30%)(10A )  5.5V 
≥ 1.35µH
A 2µH inductor will produce 20% ripple current. The peak
inductor current will be the maximum DC value plus one
half the ripple current, or 11.5A. The minimum on-time
occurs at maximum VIN:
V
1.8V
tON(MIN ) = OUT =
= 1.1µs
V
f
5.5V
300kHz
(
)
(
)
IN
The RSENSE resistors value can be calculated by using the
maximum current sense voltage specification with some
accomodation for tolerances:
RSENSE =
50mV
≈ 0.005Ω
11.5A
The power dissipation on the topside MOSFET can be
easily estimated. Using a Siliconix Si4420DY for example;
RDS(ON) = 0.013Ω, CRSS = 300pF. At maximum input
voltage with Tj (estimated) = 110°C at an elevated ambient
temperature:
PMAIN =
1.8V
2
10 ) 1+ ( 0.005) (110°C − 25°C) 
(
5.5V
0.013Ω + 1.7 ( 5.5V ) (10A ) ( 300pF )
2
(310kHz )= 0.61W
The worst-case power disipated by the synchronous
MOSFET under normal operating conditions at elevated
ambient temperature and estimated 50°C junction
temperature rise is:
PSYNC =
5.5V − 1.8V
2
10A ) (1.48 ) ( 0.013Ω )
(
5.5V
= 1.29W
A short-circuit to ground will result in a folded back
current of:
25mV 1  200ns ( 5.5V ) 
I SC =
+ 
 = 5.28A
0.005Ω 2 
2µH

The worst-case power disipated by the synchronous
MOSFET under short-circuit conditions at elevated ambi‑
ent temperature and estimated 50°C junction temperature
rise is:
Choosing 1% resistors: R1 = 16.5k and R2 = 13.2k yields
an output voltage of 1.80V.
PSYNC =
5.5V − 1.8V
2
5.28A ) (1.48 ) ( 0.013Ω )
(
5.5V
= 360mW
3729fb
22
LTC3729
APPLICATIONS INFORMATION
which is much less than normal, full-load conditions.
Incidentally, since the load no longer dissipates power in
the shorted condition, total system power dissipation is
decreased by over 99%.
The duty cycles when the peak RMS input current occurs
is at D = 0.25 and D = 0.75 according to Figure 4. Calculate
the worst-case required RMS input current rating at the
input voltage, which is 5.5V, that provides a duty cycle
nearest to the peak.
From Figure 4, CIN will require an RMS current rating of:
CIN requiredIRMS = ( 20A ) ( 0.23)
= 4.6ARMS
The output capacitor ripple current is calculated by using
the inductor ripple already calculated for each inductor and
multiplying by the factor obtained from Figure 3 along with
the calculated duty factor. The output ripple in continuous
mode will be highest at the maximum input voltage. From
Figure 3, the maximum output current ripple is:
VOUT
(0.34)
fL
1.8 ( 0.34)
∆ICOUTMAX =
= 1A
(300kHz )(2µH)
∆ICOUT =
Note that the PolyPhase technique will have its maximum
benefit for input and output ripple currents when the number
of phases times the output voltage is approximately equal
to or greater than the input voltage.
PC Board Layout Checklist
When laying out the printed circuit board, the following
checklist should be used to ensure proper operation of
the LTC3729. These items are also illustrated graphically
in the layout diagram of Figure 11. Check the following
in your layout:
1) Are the signal and power grounds segregated? The
LTC3729 signal ground pin should return to the (–) plate of
COUT separately. The power ground returns to the sources
of the bottom N-channel MOSFETs, anodes of the Schottky
diodes, and (–) plates of CIN, which should have as short
lead lengths as possible.
2) Does the LTC3729 VOS+ pin connect to the (+) plate(s)
of COUT? Does the LTC3729 VOS– pin connect to the (–)
plate(s) of COUT? The resistive divider R1, R2 must be
connected between the VDIFFOUT and signal ground and
any feedforward capacitor across R1 should be as close
as possible to the LTC3729.
3) Are the SENSE– and SENSE+ leads routed together with
minimum PC trace spacing? The filter capacitors between
SENSE+ and SENSE– pin pairs should be as close as
possible to the LTC3729. Ensure accurate current sensing
with Kelvin connections to the sense resistors.
4) Do the (+) plates of CIN connect to the drains of the topside
MOSFETs as closely as possible? This capacitor provides
the AC current to the MOSFETs. Keep the input current path
formed by the input capacitor, top and bottom MOSFETs,
and the Schottky diode on the same side of the PC board in
a tight loop to minimize conducted and radiated EMI.
5) Is the INTVCC 1µF ceramic decoupling capacitor con‑
nected closely between INTVCC and the power ground pin?
This capacitor carries the MOSFET driver peak currents.
A small value is used to allow placement immediately
adjacent to the IC.
6) Keep the switching nodes, SW1 (SW2), away from sen‑
sitive small-signal nodes. Ideally the switch nodes should
be placed at the furthest point from the LTC3729.
7) Use a low impedance source such as a logic gate to drive
the PLLIN pin and keep the lead as short as possible.
8) Minimize the capacitive load on the CLKOUT pin to
minimize excess phase shift. Buffer if necessary with an
NPN emitter follower.
3729fb
23
LTC3729
APPLICATIONS INFORMATION
The diagram in Figure 9 illustrates all branch currents in
a 2-phase switching regulator. It becomes very clear after
studying the current waveforms why it is critical to keep
the high-switching-current paths to a small physical size.
High electric and magnetic fields will radiate from these
“loops” just as radio stations transmit signals. The output
capacitor ground should return to the negative terminal of
the input capacitor and not share a common ground path
with any switched current paths. The left half of the circuit
gives rise to the “noise” generated by a switching regulator.
The ground terminations of the sychronous MOSFETs and
Schottky diodes should return to the bottom plate(s) of the
SW1
input capacitor(s) with a short isolated PC trace since very
high switched currents are present. A separate isolated
path from the bottom plate(s) of the input capacitor(s)
should be used to tie in the IC power ground pin (PGND)
and the signal ground pin (SGND). This technique keeps
inherent signals generated by high current pulses from
taking alternate current paths that have finite impedances
during the total period of the switching regulator. External
OPTI-LOOP compensation allows overcompensation for
PC layouts which are not optimized but this is not the
recommended design procedure.
L1
RSENSE1
D1
VIN
VOUT
RIN
CIN
+
+
SW2
L2
COUT
RL
RSENSE2
D2
BOLD LINES INDICATE
HIGH, SWITCHING
CURRENT LINES.
KEEP LINES TO A
MINIMUM LENGTH.
3729 F09
Figure 9. Instantaneous Current Path Flow in a Multiple Phase Switching Regulator
3729fb
24
LTC3729
APPLICATIONS INFORMATION
Simplified Visual Explanation of How a 2-Phase
Controller Reduces Both Input and Output RMS Ripple
Current
A multiphase power supply significantly reduces the amount
of ripple current in both the input and output capacitors.
The RMS input ripple current is divided by, and the effective
ripple frequency is multiplied up by the number of phases
used (assuming that the input voltage is greater than the
number of phases used times the output voltage). The output
ripple amplitude is also reduced by, and the effective ripple
frequency is increased by the number of phases used. Figure
10 graphically illustrates the principle.
illustrate how the input and output currents are reduced by
using an additional phase. The input current peaks drop in
half and the frequency is doubled for a 2-phase converter.
The input capacity requirement is reduced theoretically by a
factor of four! A ceramic input capacitor with its unbeatably
low ESR characteristic can be used.
Figure 4 illustrates the RMS input current drawn from the
input capacitance versus the duty cycle as determined
by the ratio of input and output voltage. The peak input
RMS current level of the single phase system is reduced
by 50% in a 2-phase solution due to the current splitting
between the two stages.
An interesting result of the multi-phase solution is that the
VIN which produces worst-case ripple current for the input
capacitor, VOUT = VIN/2, in the single phase design produces
zero input current ripple in the 2-phase design.
SINGLE PHASE
SW V
ICIN
The output ripple current is reduced significantly when
compared to the single phase solution using the same
inductance value because the VOUT/L discharge current
term from the stage(s) that has its bottom MOSFET on
subtracts current from the (VIN - VOUT)/L charging current
resulting from the stage which has its top MOSFET on.
The output ripple current is:
ICOUT
DUAL PHASE
SW1 V
SW2 V
IL1
IL2
IRIPPLE =
2VOUT  1− 2D (1−D) 


fL  1− 2D + 1 
where D is duty factor.
ICIN
ICOUT
RIPPLE
3729 F10
Figure 10. Single and PolyPhase Current Waveforms
The worst-case RMS ripple current for a single stage design
peaks at twice the value of the output voltage . The worstcase RMS ripple current for a two stage design results in
peaks at 1/4 and 3/4 of input voltage. When the RMS cur‑
rent is calculated, higher effective duty factor results and
the peak current levels are divided as long as the currents
in each stage are balanced. Refer to Application Note 19 for
a detailed description of how to calculate RMS current for
the single stage switching regulator. Figures 3 and 4 help to
The input and output ripple frequency is increased by
the number of stages used, reducing the output capacity
requirements. When VIN is approximately equal to NVOUT
as illustrated in Figures 3 and 4, very low input and output
ripple currents result.
Again, the interesting result of 2-phase operation results
in no output ripple at VOUT = VIN/2. The addition of more
phases by phase locking additional controllers always
results in no net input or output ripple at VOUT/VIN ratios
equal to the number of stages implemented. Designing a
system with a multiple of stages close to the VOUT/VIN ratio
will significantly reduce the ripple voltage at the input and
outputs and thereby improve efficiency, physical size, and
heat generation of the overall switching power supply.
3729fb
25
LTC3729
TYPICAL APPLICATIONS
OPTIONAL
SYNC
CLOCK IN
L1
2
3
8.06k, 1%
4
5
6
0.3µF
6800pF
100pF
25.5k, 1%
47k
8
9
10
11
12
470pF
13
14
SENSE1+
CLKOUT
TG1
–
SENSE1
EAIN
SW1
BOOST1
PLLFLTR
PLLIN LTC3729
VIN
BG1
PHASMD
EXTVCC
ITH
INTVCC
SGND
PGND
VDIFFOUT
VOS–
VOS+
BG2
BOOST2
SW2
SENSE2–
TG2
SENSE2+
PGOOD
27
0.47µF
26
25
M1
D7
24
23
22
21
M2
1µF
5V
1µF,6.3V
20
22µF
6.3V
GND
17
D8
16
0.47µF
15
3X330µF, 6.3V
POSCAP
VOUT
3.3V/90A
18
M4
M5
M6
D2
MBRS
340T3
L2
0.003Ω
L3
2
4
10k
5
6
1nF
SENSE1+
CLKOUT
0.003Ω
TG1
SENSE1–
EAIN
SW1
BOOST1
PLLFLTR
PLLIN LTC3729
EXTVCC
PHASMD
8
I
100pF 9 TH
SGND
10
NC
V
11 DIFFOUT
V –
12 OS+
V
13 OS
SENSE2–
14
SENSE2+
VIN
BG1
INTVCC
PGND
BG2
BOOST2
SW2
TG2
PGOOD
27
0.47µF
26
25
M7
D9
24
23
22
21
M8
10Ω
1µF,6.3V
20
22µF
6.3V
3
4
10k
5
6
1nF
TG1
SENSE1–
EAIN
SW1
BOOST1
PLLFLTR
PLLIN LTC3729
PHASMD
8
I
100pF 9 TH
SGND
10
NC
V
11 DIFFOUT
V –
12 OS+
V
13 OS
SENSE2–
14
SENSE2+
VIN
BG1
EXTVCC
INTVCC
PGND
BG2
BOOST2
SW2
TG2
PGOOD
17
D10
16
0.47µF
15
M10
M11
M12
27
0.47µF
26
25
0.003Ω
L5
0.003Ω
M13
D11
24
23
22
21
M14
M15
10Ω
D5
MBRS
340T3
3X330µF, 6.3V
1µF
5V
VIN
12V
D4
MBRS
340T3
L4
28
1µF,6.3V
20
22µF
6.3V
2X150µF
16V
GND
POSCAP
19
18
17
16
15
D12
0.47µF
M16
1000pF
VIN: 12V
VOUT: 3.3V/90A
SWITCHING FREQUENCY = 400kHz
POSCAP
+
7
SENSE1+
CLKOUT
GND
18
+
2
RUN/SS
2X150µF
16V
19
+
1
D3
MBRS
340T3
3X330µF, 6.3V
1µF
5V
1000pF
1000pF
M9
+
7
RUN/SS
28
+
1
3
0.01µF
2X150µF
16V
19
+
1000pF
47pF
D1
MBRS
340T3
75k
24k
0.01µF
M3
10Ω
1000pF
47pF
0.003Ω
28
+
7
RUN/SS
+
0.33µF
1
+
1000pF
M17
L6
MI – M18: Si7440DP
L1 – L6: 1µH PANASONIC ETQP6F1R0S
D7 – D12: CENTROL CMDSH-3TR
M18
D6
MBRS
340T3
0.003Ω
OUTPUT CAPACITORS: SANYO 6TPB330M
3729 TA03
Figure 11. High Current 3.3V/90A 6-Phase Application
3729fb
26
LTC3729
PACKAGE DESCRIPTION
(For purposes of clarity, drawings are not to scale)
G Package
28-Lead Plastic SSOP (5.3mm)
(Reference LTC DWG # 05-08-1640)
9.90 – 10.50*
(.390 – .413)
28 27 26 25 24 23 22 21 20 19 18 17 16 15
1.25 ±0.12
7.8 – 8.2
5.3 – 5.7
0.42 ±0.03
7.40 – 8.20
(.291 – .323)
0.65 BSC
1 2 3 4 5 6 7 8 9 10 11 12 13 14
RECOMMENDED SOLDER PAD LAYOUT
2.0
(.079)
MAX
5.00 – 5.60**
(.197 – .221)
0° – 8°
0.09 – 0.25
(.0035 – .010)
0.55 – 0.95
(.022 – .037)
NOTE:
1. CONTROLLING DIMENSION: MILLIMETERS
MILLIMETERS
2. DIMENSIONS ARE IN
(INCHES)
0.65
(.0256)
BSC
0.22 – 0.38
(.009 – .015)
TYP
0.05
(.002)
MIN
G28 SSOP 0204
3. DRAWING NOT TO SCALE
*DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED .152mm (.006") PER SIDE
**DIMENSIONS DO NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED .254mm (.010") PER SIDE
3729fb
27
LTC3729
PACKAGE DESCRIPTION
(For purposes of clarity, drawings are not to scale)
UH Package
32-Lead Plastic QFN (5mm × 5mm)
(Reference LTC DWG # 05-08-1693 Rev D)
0.70 ±0.05
5.50 ±0.05
4.10 ±0.05
3.50 REF
(4 SIDES)
3.45 ± 0.05
3.45 ± 0.05
PACKAGE OUTLINE
0.25 ± 0.05
0.50 BSC
RECOMMENDED SOLDER PAD LAYOUT
APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED
5.00 ± 0.10
(4 SIDES)
BOTTOM VIEW—EXPOSED PAD
0.75 ± 0.05
R = 0.05
TYP
0.00 – 0.05
R = 0.115
TYP
PIN 1 NOTCH R = 0.30 TYP
OR 0.35 × 45° CHAMFER
31 32
0.40 ± 0.10
PIN 1
TOP MARK
(NOTE 6)
1
2
3.50 REF
(4-SIDES)
3.45 ± 0.10
3.45 ± 0.10
(UH32) QFN 0406 REV D
0.200 REF
NOTE:
1. DRAWING PROPOSED TO BE A JEDEC PACKAGE OUTLINE
M0-220 VARIATION WHHD-(X) (TO BE APPROVED)
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.20mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
ON THE TOP AND BOTTOM OF PACKAGE
0.25 ± 0.05
0.50 BSC
3729fb
28
LTC3729
REVISION HISTORY
(Revision history begins at Rev B)
REV
DATE
DESCRIPTION
PAGE NUMBER
B
03/11
Updated Absolute Maximum Ratings section
2
Replaced Graph G09
5
Updated text and equation in Differential Amplifier/Output Voltage section
17
Updated Figure 11, Figure 12
Updated Related Parts
26, 30
30
3729fb
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa‑
tion that the interconnection of its circuits as described herein will not infringe on existing patent rights.
29
LTC3729
TYPICAL APPLICATION
L1
3
4
5
13.2k
6
33pF
1000pF
8
9
16.5k
10
11
12
100pF
13
14
TG1
–
SENSE1
SW1
EAIN
BOOST1
PLLFLTR
VIN
BG1
PLLIN
EXTVCC
PHASMD
ITH
LTC3729
SGND
VDIFFOUT
VOS–
INTVCC
PGND
BG2
BOOST2
VOS+
SENSE2–
SENSE2+
SW2
TG2
PGOOD
27
0.47µF
26
25
M1
D3
24
10Ω
23
22
21
0.1µF
5V
1µF,6.3V
20
D1
UPS840
CIN
4.7µF
6.3V
COUT
19
18
D4
17
16
100k
0.47µF
15
POWER
GOOD
1000pF
VIN: 5V TO 16V
VOUT: 3.3V/30A
SWITCHING FREQUENCY = 250kHz
M2
+
3.3k
7
SENSE1+
0.003Ω
28
+
2
0.1µF
CLKOUT
RUN/SS
+
1
1000pF
D2
UPS840
M3
M4
L2
MI, M3: IRF7811
M2, M4: IRF7809
L1, L2: 1µH SUMIDA CEP125-1R0MC-H
VIN
6V TO
16V
0.003Ω
VOUT
3.3V/30A
CIN: OS CON 2-16SP270M
COUT: KEMET 3-T510 470mF
D3, D4: CENTRAL CMDSH-3TR
3729TA02
Figure 12. 3.3V/30A Power Supply with Active Voltage Positioning
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LTC3856
Single Output 2-Channel Polyphase Synchronous Step-Down
DC/DC Controller with Diff Amp and up to 12-Phase Operation
PLL Fixed 250kHz to 770kHz Frequency, 4.5V ≤ VIN ≤ 38V,
0.8V≤ VOUT ≤ 5V
LTC3880/LTC3880-1 Dual Output PolyPhase Step-Down DC/DC Controller with
Digital Power System Management
LTC3829
Single Output 3-Channel Polyphase Synchronous Step-Down
DC/DC Controller with Diff Amp and up to 6-Phase Operation
I2C/PMBus Interface with EEPROM and 16-Bit ADC, VIN Up to 24V,
0.5V ≤ VOUT ≤ 5.5V, Analog Control Loop
PLL Fixed 250kHz to 770kHz Frequency, 4.5V ≤ VIN ≤ 38V,
0.8V ≤ VOUT ≤ 5V
LTC3869/LTC3869-2 Dual Output, 2-Phase Synchronous Step-Down DC/DC
Controller, with Accurate Current Share
PLL Fixed 250kHz to 750kHz Frequency, 4V ≤ VIN ≤ 38V,
VOUT3 Up to 12.5V
LTC3850/LTC3850-1 Dual Output, 2-Phase Synchronous Step-Down DC/DC
LTC3850-2
Controller, RSENSE or DCR Current Sensing
PLL Fixed 250kHz to 780kHz Frequency, 4V ≤ VIN ≤ 30V,
0.8V ≤ VOUT ≤ 5.25V
LTC3855
Dual Output, 2-phase, Synchronous Step-Down DC/DC
Controller with Diff Amp and DCR Temperature Compensation
PLL Fixed Frequency 250kHz to 770kHz, 4.5V ≤ VIN ≤ 38V,
0.8V ≤ VOUT ≤ 12V
LTC3853
Triple Output, Multiphase Synchronous Step-Down DC/DC
Controller, RSENSE or DCR Current Sensing and Tracking
PLL Fixed 250kHz to 750kHz Frequency, 4V ≤ VIN ≤ 24V,
VOUT3 Up to 13.5V
LTC3860
Dual, Multiphase, Synchronous Step-Down DC/DC Controller
with Diff Amp and Three-State Output Drive
Operates with Power Blocks, DRMOS Devices or External
MOSFETs 3V ≤ VIN ≤ 24V, tON(MIN) = 20ns
LTC3857/LTC3857-1 Low IQ, Dual Output 2-Phase Synchronous Step-Down DC/DC
Controller with 99% Duty Cycle
Phase-Lockable Fixed Operating Frequency 50kHz to 900kHz,
4V ≤ VIN ≤ 38V, 0.8V ≤ VOUT ≤ 24V, IQ = 50µA
3729fb
30 Linear Technology Corporation
0311 REV B • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
 LINEAR TECHNOLOGY CORPORATION 2001