12-Bit, Integrated, Multiformat SDTV/HDTV Video Decoder and RGB Graphics Digitizer ADV7403 FEATURES GENERAL DESCRIPTION Four Noise Shaped Video® 12-bit ADCs sampling up to 140 MHz (140 MHz speed grade only) 12 analog input channel mux SCART fast blank support Internal antialias filters NTSC/PAL/SECAM color standards support 525p-/625p-component progressive scan support 720p-/1080i-component HDTV support Digitizes RGB graphics up to 1280 × 1024 @ 75 Hz (SXGA) (140 MHz speed grade only) 24-bit digital input port supports data from DVI/HDMI Rx IC Any-to-any, 3 × 3 color-space conversion matrix Industrial temperature range (−40°C to +85°C) 12-bit 4:4:4/10-/8-bit 4:2:2 DDR pixel output interface Programmable interrupt request output pin VBI data slicer (including teletext) The ADV7403 is a high quality, single chip, multiformat video decoder and graphics digitizer. This multiformat decoder supports the conversion of PAL, NTSC, and SECAM standards in the form of composite or S-video into a digital ITU-R BT.656 format. The ADV7403 also supports the decoding of a component RGB/YPrPb video signal into a digital YCrCb or RGB pixel output stream. The support for component video includes standards such as 525i, 625i, 525p, 625p, 720p, 1080i, 1250i, and many other HD and SMPTE standards. Graphic digitization is also supported by the ADV7403; it is capable of digitizing RGB graphics signals from VGA to SXGA rates and converting them into a digital RGB or YCrCb pixel output stream. SCART and overlay functionality are enabled by the ADV7403’s ability to simultaneously process CVBS and standard definition RGB signals. The mixing of these signals is controlled by the fast blank pin. APPLICATIONS LCD/DLP™ rear projection HDTVs PDP HDTVs CRT HDTVs LCD/DLP front projectors LCD TV (HDTV ready) HDTV STBs with PVR Hard-disk-based video recorders Multiformat scan converters DVD recorders with progressive scan input support AVR receiver The ADV7403 contains two main processing sections. The first is the standard definition processor (SDP), which processes all PAL, NTSC, and SECAM signal types. The second is the component processor (CP), which processes YPrPb and RGB component formats, including RGB graphics. For more specific descriptions of the ADV7403 features, see the Detailed Functionality and Detailed Description sections. Rev. SpA Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 © 2005 Analog Devices, Inc. All rights reserved. ADV7403 TABLE OF CONTENTS Functional Block Diagram .............................................................. 3 CP Pixel Data Output Modes ................................................... 13 Electrical Characteristics ................................................................. 4 Composite and S-Video Processing......................................... 13 Video Specifications ......................................................................... 6 Component Video Processing .................................................. 14 Timing Characteristics..................................................................... 7 RGB Graphics Processing ......................................................... 14 Analog Specifications....................................................................... 8 Digital Video Input Port............................................................ 14 Absolute Maximum Ratings............................................................ 9 General Features......................................................................... 14 Stress Ratings ................................................................................ 9 Detailed Description ...................................................................... 15 Package Thermal Performance................................................... 9 Analog Front End....................................................................... 15 Thermal Specifications ................................................................ 9 Standard Definition Processor ................................................. 15 ESD Caution.................................................................................. 9 Component Processor ............................................................... 15 Pin Configuration and Function Descriptions........................... 10 Pixel Input/Output Formatting .................................................... 17 Timing Diagrams............................................................................ 12 Recommended External Loop Filter Components.................... 19 Detailed Functionality ................................................................... 13 Typical Connection Diagram ....................................................... 20 Analog Front End ....................................................................... 13 Outline Dimensions ....................................................................... 21 SDP Pixel Data Output Modes ................................................. 13 Ordering Guide .......................................................................... 21 REVISION HISTORY 9/05—Rev. Sp0 to Rev. SpA Deleted EDTV.....................................................................Universal Added AVR Receiver to Applications Section.............................. 1 Change to Crystal Normal Frequency Typ Value in Table 3 ...... 7 Changes to Figure 2 ....................................................................... 10 Changes to Function Descriptions of Pin 37 and Pin 38 .......... 11 Change Pin 70 Type........................................................................ 11 Change to Crystal MHz Unit Value ............................................. 13 Added Pixel Input Information to Table 9 and Table 10 ........... 17 Changes to Figure 9........................................................................ 20 4/05—Revision Sp0: Initial Version Rev. SpA | Page 2 of 24 Figure 1. Rev. SpA | Page 3 of 24 05431-001 P40–P31 P29–P20 24 P11–P10 P1–P0 SOG SOY DE_IN HS_IN VS_IN DCLK_IN SCLK SCLK2 SDA SDA2 ALSB FB CVBS S-VIDEO YPrPb SCART– (RGB + CVBS) GRAPHICS RGB AIN1 12 TO AIN12 A/D ANTIALIAS FILTER CLAMP STDI DVI or HDMI DIGITAL INPUT PORT XTAL XTAL1 SSPD SYNC PROCESSING AND CLOCK GENERATION 8 8 8 A/D ANTIALIAS FILTER A/D A/D CLAMP ANTIALIAS FILTER SERIAL INTERFACE CONTROL AND VBI DATA INPUT MUX CLAMP CLAMP ANTIALIAS FILTER ADV7403 12 12 12 12 COLORSPACE CONVERSION 12 12 12 DECIMATION AND DOWNSAMPLING 12 FILTERS DATA PREPROCESSOR 12 12 12 Cb Cr C CVBS DIGITAL FINE CLAMP ACTIVE PEAK AND AGC CHROMA DEMOD FSC RECOVERY CVBS/Y MACROVISION DETECTION CHROMA RESAMPLE RESAMPLE CONTROL LUMA RESAMPLE CHROMA 2D COMB (4H MAX) LUMA 2D COMB (5H MAX) GAIN CONTROL OFFSET CONTROL CGMS DATA EXTRACTION Cb Cr Y Cb Cr Y AV CODE INSERTION FAST BLANK OVERLAY CONTROL AND AV CODE INSERTION VBI DATA RECOVERY COMPONENT PROCESSOR MACROVISION DETECTION CHROMA FILTER SYNC EXTRACT LUMA FILTER STANDARD AUTODETECTION STANDARD DEFINITION PROCESSOR 30 20 8 8 8 INT SFL/ SYNCOUT LLC1 FIELD/DE VS HS PIXEL DATA P29–P20 P19–P10 P9–P0 ADV7403 FUNCTIONAL BLOCK DIAGRAM OUTPUT FIFO AND FORMATTER ADV7403 ELECTRICAL CHARACTERISTICS @ AVDD = 3.15 V to 3.45 V, DVDD = 1.65 V to 2.0 V, DVDDIO = 3.0 V to 3.6 V, PVDD = 1.71 V to 1.89 V, nominal input range 1.6 V. Operating temperature range, a otherwise noted. Table 1. Parameter 1, 2 , 3 STATIC PERFORMANCE 4, 5 Resolution (each ADC) Integral Nonlinearity Integral Nonlinearity Integral Nonlinearity Integral Nonlinearity Integral Nonlinearity Differential Nonlinearity Differential Nonlinearity Differential Nonlinearity Differential Nonlinearity Differential Nonlinearity DIGITAL INPUTS Input High Voltage 7 Input Low Voltage 8 Input High Voltage Input Low Voltage Input Current Input Capacitance 10 DIGITAL OUTPUTS Output High Voltage 11 Output Low Voltage11 High Impedance Leakage Current Output Capacitance10 POWER REQUIREMENTS10 Digital Core Power Supply Digital I/O Power Supply PLL Power Supply Analog Power Supply Digital Core Supply Current Symbol Test Conditions N INL INL INL INL INL DNL DNL DNL DNL DNL BSL at 27 MHz (at a 12-bit level) BSL at 54 MHz (at a 12-bit level) BSL at 74 MHz (at a 10-bit level) BSL at 110 MHz (at a 10-bit level) BSL at 135 MHz (at an 8-bit level) 6 At 27 MHz (at a 12-bit level) At 54 MHz (at a 12-bit level) At 74 MHz (at a 10-bit level) At 110 MHz (at a 10-bit level) At 135 MHz (at an 8-bit level)6 VIH VIL VIH VIL IIN Min Typ ±2.0 −2.0/+2.5 ±1.0 −3.0/+3.0 ±1.3 −0.7/+0.85 −0.75/+0.9 ±0.75 −0.7/+5.0 −0.8/+2.5 Digital I/O Supply Current IDVDDIO PLL Supply Current IPVDD Analog Supply Current 13 IAVDD Power-Down Current Green Mode Power-Down Power-Up Time IPWRDN IPWRDNG TPWRUP 12 ±8.0 Bits LSB LSB LSB LSB LSB LSB LSB LSB LSB LSB −0.99/+2.5 0.3 +60 +10 10 V V V V μA μA pF 0.4 60 10 20 V V μA μA pF 0.8 HS_IN, VS_IN low trigger mode HS_IN, VS_IN low trigger mode Pins listed in Note 9 All other input pins 0.7 −60 −10 ISOURCE = 0.4 mA ISINK = 3.2 mA Pins listed in Note 12 All other output pins 2.4 COUT DVDD DVDDIO PVDD AVDD IDVDD Unit 2 CIN VOH VOL ILEAK Max 1.65 3.0 1.71 3.15 CVBS input sampling at 54 MHz Graphics RGB sampling at 135 MHz SCART RGB FB sampling at 54 MHz CVBS input sampling at 54 MHz Graphics RGB sampling at 135 MHz CVBS input sampling at 54 MHz Graphics RGB sampling at135 MHz CVBS input sampling at 54 MHz Graphics RGB sampling at 135 MHz SCART RGB FB sampling at 54 MHz Sync bypass function 1 1.8 3.3 1.8 3.3 105 137 106 4 19 11 12 99 242 269 2.25 16 20 2 3.6 1.89 3.45 V V V V mA mA mA mA mA mA mA mA mA mA mA mA ms The min/max specifications are guaranteed over this range. Temperature range TMIN to TMAX: −40°C to +85°C (0°C to 70°C temperature range for ADV7403KSTZ-140). 3 All specifications obtained using programming scripts with the following sequence included: Addr 0x0E - data 0x80, Addr 0x54 - data 0x00, Addr 0x0E - data 0x00. 2 Rev. SpA | Page 4 of 24 ADV7403 4 All ADC linearity tests performed at input range of full scale − 12.5%, and at zero scale + 12.5%. Max INL and DNL specifications obtained with part configured for component video input. 6 Specification for ADV7403KSTZ-140 only. 7 To obtain specified VIH level on Pin 38, Register 0x13 (wo) must be programmed with value 0x04. If Register 0x13 is programmed with value 0x00, then VIH on Pin 38 = 1.2 V. 8 To obtain specified VIL level on Pin 38, Register 0x13 (wo) must be programmed with value 0x04. If Register 0x13 is programmed with value 0x00, then VIL on Pin 38 = 0.4 V. 9 Pins 1, 2, 13, 14, 16, 19, 24, 29, 30, 31, 32, 33, 34, 35, 45, 78, 79, 83, 84, 87, 88, 95, 96, 97, 100. 10 Guaranteed by characterization. 11 VOH and VOL levels obtained using default drive strength value (0xD5) in Register Subaddress 0xF4. 12 Pins 3, 13, 14, 19, 24, 29, 30, 31, 32, 33, 34, 45. 13 Analog current measurements for CVBS made with ADC0 powered up only, For RGB, ADC0, ADC1, and ADC2 powered up only, for SCART FB, all ADCs powered up. 5 Rev. SpA | Page 5 of 24 ADV7403 VIDEO SPECIFICATIONS @ AVDD= 3.15 V to 3.45 V, DVDD = 1.65 V to 2.0 V, DVDDIO = 3.0 V to 3.6 V, PVDD = 1.71 V to 1.89 V. Operating temperature range, unless otherwise noted. Table 2. Parameter 1, 2 , 3 NONLINEAR SPECIFICATIONS Differential Phase Differential Gain Luma Nonlinearity NOISE SPECIFICATIONS SNR Unweighted SNR Unweighted Analog Front End Crosstalk LOCK TIME SPECIFICATIONS Horizontal Lock Range Vertical Lock Range FSC Subcarrier Lock Range Color Lock in Time Sync Depth Range 4 Color Burst Range Vertical Lock Time Horizontal Lock Time CHROMA SPECIFICATIONS Hue Accuracy Color Saturation Accuracy Color AGC Range Chroma Amplitude Error Chroma Phase Error Chroma Luma Intermodulation LUMA SPECIFICATIONS Luma Brightness Accuracy Luma Contrast Accuracy Symbol Test Conditions DP DG LNL CVBS input, modulated 5 step CVBS input, modulated 5 step CVBS input, 5 step Luma ramp Luma flat field Min 61 64 Typ Max 0.4 0.4 0.4 degree % % 64 65 60 dB dB dB −5 40 +5 70 ±1.3 60 20 5 200 200 2 100 HUE CL_AC 1 1 1 The min/max specifications are guaranteed over this range. Temperature range TMIN to TMAX: −40°C to +85°C (0°C to 70°C temperature range for ADV7403KSTZ-140). 3 Guaranteed by characterization. 4 Nominal sync depth is 300 mV at 100% sync depth range. 2 Rev. SpA | Page 6 of 24 % Hz kHz line % % field line 0.4 0.3 0.1 degree % % % degree % 1 1 % % 5 CVBS, 1 V input CVBS, 1 V input Unit 400 ADV7403 TIMING CHARACTERISTICS @ AVDD = 3.15 V to 3.45 V, DVDD = 1.65 V to 2.0 V, DVDDIO = 3.0 V to 3.6 V, PVDD = 1.71 V to 1.89 V. Operating temperature range, unless otherwise noted. Table 3. Parameter 1, 2 , 3 SYSTEM CLOCK AND CRYSTAL Crystal Nominal Frequency Crystal Frequency Stability Horizontal Sync Input Frequency LLC1 Frequency Range 4 I2C PORT 5 SCLK Frequency SCLK Min Pulse Width High SCLK Min Pulse Width Low Hold Time (Start Condition) Setup Time (Start Condition) SDA Setup Time SCLK and SDA Rise Time SCLK and SDA Fall Time Setup Time for Stop Condition RESET FEATURE Reset Pulse Width CLOCK OUTPUTS LLC1 Mark Space Ratio Symbol Test Conditions Min Typ Max Unit ±50 110 140 MHz ppm kHz MHz 28.63636 14.8 12.825 400 t1 t2 t3 t4 t5 t6 t7 t8 0.6 1.3 0.6 0.6 100 300 300 0.6 5 t9:t10 DATA and CONTROL OUTPUTS Data Output Transition Time SDR (SDP) 6 t11 Data Output Transition Time SDR (SDP)6 t12 Data Output Transition Time SDR (CP) 7 t13 Data Output Transition Time SDR (CP)7 t14 Data Output Transition Time DDR (CP)7, 8 t15 Data Output Transition Time DDR (CP)7, 8 t16 Data Output Transition Time DDR (CP)7, 8 t17 Data Output Transition Time DDR (CP)7, 8 t18 DATA and CONTROL INPUTS5 Input Setup Time (Digital Input Port) t19 Input Hold Time (Digital Input Port) t20 45:55 Negative clock edge to start of valid data End of valid data to negative clock edge End of valid data to negative clock edge Negative clock edge to start of valid data Positive clock edge to end of valid data Positive clock edge to start of valid data Negative clock edge to end of valid data Negative clock edge to start of valid data HS_IN, VS_IN DE_IN, data inputs HS_IN, VS_IN DE_IN, data inputs 1 The min/max specifications are guaranteed over this range. Temperature range TMIN to TMAX: −40°C to +85°C (0°C to 70°C temperature range for ADV7403KSTZ-140). Guaranteed by characterization. 4 Maximum LLC1 frequency is 110 MHz for ADV7403BSTZ-110. 5 TTL input values are 0 V to 3 V, with rise/fall times ≥3 ns, measured between the 10% and 90% points. 6 SDP timing figures obtained using default drive strength value (0xD5) in register subaddress 0xF4. 7 CP timing figures obtained using max drive strength value (0xFF) in Register Subaddress 0xF4. 8 DDR timing specifications dependent on LLC1 output pixel clock; TLCC1/4 = 9.25 ns at LLC1 = 27 MHz. 2 3 Rev. SpA | Page 7 of 24 kHz μs μs μs μs ns ns ns μs ms 55:45 % duty cycle 3.6 ns 2.4 ns 2.8 ns 0.1 ns −4 + TLLC1/4 ns 0.25 + TLLC1/4 ns −2.95 + TLLC1/4 ns −0.5 + TLLC1/4 ns 9 2.2 7 2 ns ns ns ns ADV7403 ANALOG SPECIFICATIONS @ AVDD = 3.1.5 V to 3.45 V, DVDD = 1.65 V to 2.0 V, DVDDIO = 3.0 V to 3.6 V, PVDD = 1.71 V to 1.89 V. Operating temperature range, unless otherwise noted. Recommended analog input video signal range: 0.5 V to 1.6V , typically 1 V p-p. Table 4. Parameter 1, 2 , 3 CLAMP CIRCUITRY External Clamp Capacitor Input Impedance 4 Input Impedance of Pin 51 (FB) CML ADC Full-Scale Level ADC Zero-Scale Level ADC Dynamic Range Clamp Level (When Locked) Large Clamp Source Current Large Clamp Sink Current Fine Clamp Source Current Fine Clamp Sink Current Test Conditions Min Clamps switched off CVBS input SCART RGB input (R, G, B signals) S-Video input (Y signal) S-Video input (C signal) Component input (Y, Pr, Pb signals) PC RGB input (R, G, B signals) SDP only SDP only SDP only SDP only 1 The min/max specifications are guaranteed over this range. Temperature range TMIN to TMAX:−40°C to +85°C (0°C to 70°C temperature range for ADV7403KSTZ-140). 3 Guaranteed by characterization. 4 Except Pin 51 (FB). 2 Rev. SpA | Page 8 of 24 Typ 0.1 10 20 1.86 CML + 0.8 V CML − 0.8 V 1.6 CML − 0.292 V CML − 0.4 V CML − 0.292 V CML – 0 V CML – 0.3 V CML − 0.3 V 0.75 0.9 17 17 Max Unit μF MΩ kΩ V V V V V V V V V V mA mA μA μA ADV7403 ABSOLUTE MAXIMUM RATINGS STRESS RATINGS Table 5. Parameter AVDD to AGND DVDD to DGND PVDD to AGND DVDDIO to DGND DVDDIO to AVDD PVDD to DVDD DVDDIO to PVDD DVDDIO to DVDD AVDD to PVDD AVDD to DVDD Digital Inputs Voltage to DGND Digital Outputs Voltage to DGND Analog Inputs to AGND Maximum Junction Temperature (TJ MAX) Storage Temperature Range Infrared Reflow Soldering (20 sec) Rating 4V 2.2 V 2.2 V 4V −0.3 V to +0.3 V −0.3 V to +0.3 V −0.3 V to +2 V −0.3 V to +2 V −0.3 V to +2 V −0.3 V to +2 V DGND − 0.3 V to DVDDIO + 0.3 V DGND − 0.3 V to DVDDIO + 0.3 V AGND − 0.3 V to AVDD + 0.3 V Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. PACKAGE THERMAL PERFORMANCE To reduce power consumption when using the part the user is advised to turn off any unused ADCs . The junction temperature must always stay below the maximum junction temperature (TJ MAX) of 125°C. This equation shows how to calculate the junction temperature: TJ = TA Max + (θJA × WMax) where: TA Max = 85°C. θJA = 30°C/W. WMax = ((AVDD × IAVDD)+(DVDD × IDVDD)+ (DVDDIO × IDVDDIO) + (PVDD × IPVDD)). 125°C −65°C to +150°C 260°C THERMAL SPECIFICATIONS Table 6. Thermal Characteristics Junction-to-Case Thermal Resistance Junction-to-Ambient Thermal Resistance Symbol θJC θJA Test Conditions 4-layer PCB with solid ground plane 4-layer PCB with solid ground plane (still air) ESD CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Rev. SpA | Page 9 of 24 Typ 7 30 Unit °C/W °C/W ADV7403 1 P31 2 INT P39 P40 SCLK1 SDA1 ALSB 84 83 82 81 80 SOY VS_IN 85 AIN6 HS_IN/CS_IN 86 76 P38 87 77 P37 88 DE_IN DGND 89 RESET DVDD 90 78 P19 91 79 P17 P16 94 P18 P36 95 92 P35 96 93 FIELD/DE P34 97 VS 98 P33 100 P32 99 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS 75 AIN12 74 AIN5 3 73 AIN11 CS/HS 4 72 AIN4 DGND 5 71 AIN10 DVDDIO 6 70 TEST0 P15 7 69 CAPC2 P14 8 68 CAPC1 P13 9 67 BIAS 66 AGND PIN 1 ADV7403 P12 10 DGND 11 65 CML DVDD 12 64 REFOUT LQFP TOP VIEW (Not to Scale) 44 45 46 47 48 49 50 P0 P20 ELPF PVDD PVDD AGND AGND 05431-002 43 P1 FB 42 51 P2 25 41 SOG P7 P3 52 40 24 DGND AIN7 P27 39 53 DVDD 23 38 AIN1 P8 XTAL 54 37 22 XTAL1 AIN8 P9 36 55 35 21 LLC1 AIN2 P10 DCLK_IN 56 34 20 P21 AIN9 P11 33 57 P22 19 32 AIN3 SDA2 P23 58 31 18 30 TEST1 DVDDIO P25 59 P24 17 29 AGND DGND P26 60 28 16 P4 CAPY1 SCLK2 27 61 SFL/SYNC_OUT 26 CAPY2 15 14 P6 AVDD 13 P28 P5 63 62 P29 Figure 2. Pin Configuration Table 7. Pin Function Descriptions Pin No. 5, 11, 17, 40, 89 49, 50, 60, 66 6, 18 12, 39, 90 63 47, 48 51 54, 56, 58, 72, 74, 76, 53, 55, 57, 71, 73, 75 42, 41, 28, 27, 26, 25, 23, 22, 10, 9, 8, 7, 94, 93, 92, 91 44, 43, 21, 20, 45, 34, 33, 32, 31, 30, 29, 24, 14, 13 2, 1, 100, 97, 96, 95, 88, 87, 84, 83 Mnemonic DGND AGND DVDDIO DVDD AVDD PVDD FB AIN1 to AIN12 Type G G P P P P I I Function Digital Ground. Analog Ground. Digital I/O Supply Voltage (3.3 V). Digital Core Supply Voltage (1.8 V). Analog Supply Voltage (3.3 V). PLL Supply Voltage (1.8 V). Fast Switch Overlay Input. This pin switches between CVBS and RGB analog signals. Analog Video Input Channels. P2 to P9, P12 to P19 O Video Pixel Output Port. P0 to P1, P10 to P11, P20 to P21, P22 to P25, P26 to P29 P31 to P40 I/O Video Pixel Input/Output Port. I Video Pixel Input Port. Rev. SpA | Page 10 of 24 ADV7403 Pin No. 3 Mnemonic INT Type O 4 HS/CS O 99 98 VS FIELD/DE O O 81, 19 SDA1, SDA2 I/O 82, 16 SCLK1, SCLK2 I 80 ALSB I 78 RESET I 36 LLC1 O 38 XTAL I 37 XTAL1 O 46 70 59 15 ELPF TEST0 TEST1 SFL/SYNC_OUT O NC O O 64 65 61, 62 68, 69 67 REFOUT CML CAPY1, CAPY2 CAPC1, CAPC2 BIAS O O I I O 86 HS_IN/CS_IN I 85 79 VS_IN DE_IN I I 35 DCLK_IN I 52 77 SOG SOY I I Function Interrupt. This pin can be active low or active high. When SDP/CP status bits change, this pin triggers. The set of events that triggers an interrupt is under user control. HS is a Horizontal Synchronization Output Signal (SDP and CP modes). CS is a Digital Composite Synchronization Signal (and can be selected while in CP mode). Vertical Synchronization Output Signal (SDP and CP modes). FIELD is a Field Synchronization Output Signal (all interlaced video modes). This pin also can be enabled as a Data Enable signal (DE) in CP mode to allow direct connection to a HDMI/DVI Tx IC. I2C Port Serial Data Input/Output Pins. SDA1 is the data line for the control port, and SDA2 is the data line for the VBI readback port. I2C Port Serial Clock Input (max clock rate of 400 kHz). SCLK1 is the clock line for the Control port and SCLK2 is the clock line for the VBI data readback port. This pin selects the I2C address for the ADV7403 control and VBI readback ports. ALSB set to Logic 0 sets the address for a write to control port of 0x40 and the readback address for the VBI port of 0x21. ALSB set to a logic high sets the address for a write to control port of 0x42 and the readback address for the VBI port of 0x23. System Reset Input. Active low. A minimum low reset pulse width of 5 ms is required to reset the ADV7403 circuitry. LLC1 is a line-locked output clock for the pixel data (range is 12.825 MHz to 140 MHz for ADV7403KSTZ-140; 12.825 MHz to 110 MHz for ADV7403BSTZ-110. Input Pin for 28.63636 MHz crystal, or can be overdriven by an external 3.3 V, 28.63636 MHz clock oscillator source to clock the ADV7403. This pin should be connected to the 28.63636 MHz crystal or left as a no connect if an external 3.3 V 28.63636 MHz clock oscillator source is used to clock the ADV7403. In crystal mode the crystal must be a fundamental crystal. The recommend external loop filter must be connected to this ELPF pin. This pin should be left unconnected or alternaltely tie to AGND. This pin should be left unconnected. Subcarrier Frequency Lock (SFL). This pin contains a serial output stream, which can be used to lock the subcarrier frequency when this decoder is connected to any Analog Devices digital video encoder. SYNC_OUT is the sliced sync output signal available only in CP mode. Internal Voltage Reference Output. Common-Mode Level Pin (CML) for the internal ADCs. ADC Capacitor Network. ADC Capacitor Network. External Bias Setting Pin. Connect the recommended resistor (1.35 kΩ) between pin and ground. Can be configured in CP mode to be either a digital HS input signal or a digital CS input signal used to extract timing in a 5-wire or 4-wire RGB mode. VS Input Signal. Used in CP mode for 5-wire timing mode. Data Enable Input Signal. Used in 24-bit digital input port mode (for example, processing 24-bit RGB data from a DVI Rx IC). Clock Input Signal. Used in 24-bit digital input mode (for example, processing 24-bit RGB data from a DVI Rx IC) and also in digital CVBS input mode. Sync on Green Input. Used in embedded sync mode. Sync on Luma Input. Used in embedded sync mode. Rev. SpA | Page 11 of 24 ADV7403 TIMING DIAGRAMS t3 t5 t3 SDA1/SDA2 t6 t1 t2 t7 t4 05431-003 SCLK1/SCLK2 t8 Figure 3. I2C Timing t9 t10 LLC1 t11 t12 05431-004 P0–P29, VS, HS, FIELD/DE, SFL/SYNC_OUT Figure 4. Pixel Port and Control SDR Output Timing (SD Core) t9 t10 LLC1 t13 05431-005 t14 P0–P29, VS, HS, FIELD/DE Figure 5. Pixel Port and Control SDR Output Timing (CP Core) LLC1 t18 t15 t17 P6–P9, P10–P19 05431-006 t16 Figure 6. Pixel Port and Control DDR Output Timing (CP Core) DCLK_IN t9 t20 HS_IN VS_IN DE_IN P0–P1, P10–P11, P20–P21, P22–P29, P31–P32, P33–P40 t19 Figure 7. Digital Input Port and Control Input Timing Rev. SpA | Page 12 of 24 05431-008 CONTROL INPUTS t10 ADV7403 DETAILED FUNCTIONALITY ANALOG FRONT END • Adaptive digital line length tracking (ADLLT™) • Four 140 MHz (ADV7403KSTZ-140), Noise Shaped Video, 12-bit ADCs enable true 10-bit video decoder • Proprietary architecture for locking to weak, noisy, and unstable sources from VCRs and tuners • 12 analog input channel mux enables multisource connection without the requirement of an external mux • IF filter block compensates for high frequency luma attenuation due to tuner SAW filter • Four current and voltage clamp control loops ensure any dc offsets are removed from the video signal • Chroma transient improvement (CTI) • SCART functionality and SD RGB overlay on CVBS controlled by fast blank input • Luminance digital noise reduction (DNR) • Color controls include hue, brightness, saturation, contrast, and Cr and Cb offset controls • Certified Macrovision copy protection detection on composite and S-video for all worldwide formats (PAL/NTSC/SECAM) 8-/10-bit ITU-R BT.656 4:2:2 YCrCb with embedded time codes and/or HS, VS, and FIELD • 4× oversampling (54 MHz) for CVBS, S-video, and YUV modes 16-/20-bit YCrCb with embedded time codes and/or HS, VS, and FIELD • Line-locked clock output (LLC) • Letterbox detection supported • Free-run output mode provides stable timing when no video input is present • Vertical blanking interval data processor • Four antialias filters to remove out of band noise on standard definition input video signals. SDP PIXEL DATA OUTPUT MODES • • • 24-/30-bit YCrCb with embedded time codes and/or HS, VS, and FIELD CP PIXEL DATA OUTPUT MODES • Single data rate (SDR) 8-/10-bit 4:2:2 YCrCb for 525i, 625i • Single data rate (SDR) 16-/20-bit 4:2:2 YCrCb for all standards • Single data rate (SDR) 24-/30-bit 4:4:4 YCrCb/RGB for all standards • Vertical Interval Time Codes (VITC) • Double data rate (DDR) 8-/10-bit 4:2:2 YCrCb for all standards • Closed captioning (CC) and extended data service (EDS) • Double data rate (DDR) 12-bit 4:4:4 YCrCb/RGB for all standards • Wide screen signaling (WSS) • TeleText • Video Programming System (VPS) • Copy generation management system (CGMS) COMPOSITE AND S-VIDEO PROCESSING • • Support for NTSC (J, M, 4.43), PAL (B, D, I, G, H, M, N, 60) and SECAM B/D/G/K/L standards in the form of CVBS and S-video Superadaptive 2D 5-line comb filters for NTSC and PAL give superior chrominance and luminance separation for composite video • Full automatic detection and autoswitching of all worldwide standards (PAL/NTSC/SECAM) • Automatic gain control with white peak mode ensures the video is always processed without loss of the video processing range • Gemstar™ 1×/2× electronic program guide compatible • Clocked from a single 28.63636 MHz crystal • Subcarrier frequency lock (SFL) output for downstream video encoder • Differential gain typically 0.4% • Differential phase typically 0.4° Rev. SpA | Page 13 of 24 ADV7403 COMPONENT VIDEO PROCESSING DIGITAL VIDEO INPUT PORT • Formats supported include 525i, 625i, 525p, 625p, 720p, 1080i, and many other HDTV formats • Supports raw 8-/10-bit CVBS data from digital tuner • • Automatic adjustments include gain (contrast) and offset (brightness); manual adjustment controls are also supported Support for 24-bit RGB input data from DVI Rx chip, output converted to YCrCb 4:2:2 • Support for 24-bit 4:4:4, 16-/20-bit 4:2:2 525i, 625i, 525p, 625p, 1080i, 720p, VGA to SXGA @ 60 Hz input data from HDMI Rx chip, output converted to 16-bit 4:2:2 YCrCb • Support for analog component YPrPb/RGB video formats with embedded sync or with separate HS, VS, or CS • Any-to-any, 3 × 3 color space conversion matrix supports YCrCb-to-RGB and RGB-to-YCrCb • HS, VS, and FIELD output signals with programmable position, polarity, and width • Standard identification (STDI) enables system level component format detection • Programmable interrupt request output pin, INT, signals SDP/CP status changes • Synchronization source polarity detector (SSPD) determines the source and polarity of the synchronization signals that accompany the input video • Supports two I2C host port interfaces (control and VBI) • Low power consumption: 1.8 V digital core, 3.3 V analog and digital I/O, low power power-down mode, and green PC mode • Industrial temperature range (−40°C to +85°C) (ADV7403BSTZ-110) • 140 MHz speed grade (ADV7403KST-140) • 100-lead, 14 mm × 14 mm, Pb-free LQFP • Certified Macrovision copy protection detection on component formats (525i, 625i, 525p, and 625p) • Free-run output mode provides stable timing when no video input is present • Arbitrary pixel sampling support for nonstandard video sources GENERAL FEATURES RGB GRAPHICS PROCESSING • 140 MSPS conversion rate supports RGB input resolutions up to 1280 × 1024 @ 75 Hz (SXGA); (110 MSPS conversion rate for ADV7403BSTZ-110) • Automatic or manual clamp and gain controls for graphics modes • Contrast and brightness controls • 32-phase DLL allows optimum pixel clock sampling • Automatic detection of sync source and polarity by SSPD block • Standard identification is enabled by STDI block • RGB can be color space converted to YCrCb and decimated to a 4:2:2 format for video centric backend IC interfacing • Data enable (DE) output signal supplied for direct connection to HDMI/DVI Tx IC • Arbitrary pixel sampling support for nonstandard video sources Rev. SpA | Page 14 of 24 ADV7403 DETAILED DESCRIPTION ANALOG FRONT END The ADV7403 analog front end comprises four Noise Shaped Video, 12-bit ADCs that digitize the analog video signal before applying it to the SDP or CP (See Table 8 for sampling rates). The analog front end uses differential channels to each ADC to ensure high performance in a mixed-signal application. The front end also includes a 12-channel input mux that enables multiple video signals to be applied to the ADV7403. Current and voltage clamps are positioned in front of each ADC to ensure that the video signal remains within the range of the converter. Fine clamping of the video signals is performed downstream by digital fine clamping either in the CP or SDP. Optional antialiasing filters are positioned in front of each ADC. These filters can be used to band-limit standard definition video signals, removing spurious, out-of-band noise. The ADCs are configured to run in 4× oversampling mode when decoding composite and S-video inputs; 2× oversampling is performed for component 525i, 625i, 525p, and 625p sources. All other video standards are 1× oversampled. Oversampling the video signals reduces the cost and complexity of external anti-aliasing filters with the benefit of an increased signal-tonoise ratio (SNR). The ADV7403 can support simultaneous processing of CVBS and RGB standard definition signals to enable SCART compatibility and overlay functionality. A combination of CVBS and RGB inputs can be mixed and output under control of I2C registers and the fast blank pin. Table 8: Maximum ADC Sampling Rates Model ADV7403BSTZ-110 ADV7403KSTZ-140 Maximum ADC Sampling Rate 110 MHz 140MHz STANDARD DEFINITION PROCESSOR The SDP section is capable of decoding a large selection of baseband video signals in composite S-video and YUV formats. The video standards supported by the SDP include PAL B/D/I/G/H, PAL60, PAL M, PAL N, NTSC M/J, NTSC 4.43, and SECAM B/D/G/K/L. The ADV7403 can automatically detect the video standard and process it accordingly. The SDP has a 5-line super adaptive 2-D comb filter that gives superior chrominance and luminance separation when decoding a composite video signal. This highly adaptive filter automatically adjusts its processing mode according to video standard and signal quality with no user intervention required. The SDP has an IF filter block that compensates for attenuation in the high frequency luma spectrum due to tuner SAW filter. The SDP has specific luminance and chrominance parameter control for brightness, contrast, saturation, and hue. The ADV7403 implements a patented adaptive-digital-linelength-tracking (ADLLT) algorithm to track varying video line lengths from sources such as a VCR. ADLLT enables the ADV7403 to track and decode poor quality video sources such as VCRs, noisy sources from tuner outputs, VCD players, and camcorders. The SDP also contains a chroma transient improvement (CTI) processor. This processor increases the edge rate on chroma transitions, resulting in a sharper video image. The SDP can process a variety of VBI data services, such as TeleText, closed captioning (CC), wide screen signaling (WSS), video programming system (VPS), vertical interval time codes (VITC), copy generation management system (CGMS), Gemstar 1×/2×, and extended data service (XDS). The ADV7403 SDP section has a Macrovision 7.1 detection circuit that allows it to detect Types I, II, and III protection levels. The decoder is also fully robust to all Macrovision signal inputs. COMPONENT PROCESSOR The CP section is capable of decoding/digitizing a wide range of component video formats in any color space. Component video standards supported by the CP are 525i, 625i, 525p, 625p, 720p, 1080i, 1250i, VGA up to SXGA @ 75 Hz, (ADV7403KSTZ-140 only) and many other standards not listed here. The CP section of the ADV7403 contains an AGC block. When no embedded sync is present, the video gain can be set manually. The AGC section is followed by a digital clamp circuit that ensures the video signal is clamped to the correct blanking level. Automatic adjustments within the CP include gain (contrast) and offset (brightness); manual adjustment controls are also supported. A fully programmable any-to-any, 3 × 3 color space conversion matrix is placed between the analog front end and the CP section. This enables YPrPb-to-RGB and RGB-to-YCrCb conversions. Many other standards of color space can be implemented using the color space converter. The output section of the CP is highly flexible. It can be configured in single data rate mode (SDR) with one data packet per clock cycle or in a double data rate (DDR) mode where data is presented on the rising and falling edges of the clock. In SDR mode, a 16-/20-bit 4:2:2 or 24-/30-bit 4:4:4 output is possible. In these modes, HS, VS, and FIELD/DE (where applicable) timing reference signals are provided. In DDR mode, the ADV7403 can be configured in an 8-/10-bit 4:2:2 YcrCb or 12-bit 4:4:4 RGB/ YcrCb pixel output interface with corresponding timing signals. Rev. SpA | Page 15 of 24 ADV7403 The ADV7403 is capable of supporting an external DVI/ HDMI receiver. The digital interface expects 24-bit 4:4:4 or 16-/20-bit 4:2:2 bit data (either graphics RGB or component video YcrCb), accompanied by HS, VS, DE, and a fully synchronous clock signal. The data is processed in the CP and output as 16-bit 4:2:2 YcrCb data. VBI extraction of CGMS data is performed by the CP section of the ADV7403 for interlaced, progressive, and high definition scanning rates. The data extracted can be read back over the I2C interface. For more detailed product information about the ADV7403, contact your local ADI sales office or email [email protected]. The CP section contains circuitry to enable the detection of Macrovision encoded YPrPb signals for 525i, 625i, 525p, and 625p. It is designed to be fully robust when decoding these types of signals. Rev. SpA | Page 16 of 24 ADV7403 PIXEL INPUT/OUTPUT FORMATTING Table 9. SDP, CP Pixel Input/Output Pin Map (P19 to P0) Processor, Format, and Mode SDP Video out, 8-bit, 4:2:2 SDP Video out, 10-bit, 4:2:2 SDP Video out, 16-bit, 4:2:2 SDP Video out, 20-bit, 4:2:2 SDP Video out, 24-bit, 4:4:4 SDP Video out, 30-bit, 4:4:4 SM-SDP Digital tuner input[1] CP 8-bit, 4:2:2, DDR CP 10-bit, 4:2:2, DDR CP 12-bit, 4:4:4, RGB DDR CP Video out, 16-bit, 4:2:2 CP Video out, 20-bit, 4:2:2 CP Video out, 24-bit, 4:4:4 CP Video out, 30-bit, 4:4:4 SM-CP HDMI receiver support, 24-bit, 4:4:4 input SM-CP HDMI receiver support 16-bit pass-through SM-CP HDMI receiver support, 20-bit, pass-through 19 18 17 16 15 14 YcrCb[7:0]OUT 13 12 Pixel Port Pins P[19:0] 11 10 9 8 7 - YcrCb[9:0] OUT - Y[7:0]OUT - - - 6 - - 5 - 4 - 3 - 2 - - - - - - CrCb[7:0]OUT Y[9:0]OUT 1 - 0 - - - - - - - - - - - - - CrCb[9:0]OUT Y[7:0]OUT - - Cb[7:0]OUT Y[9:0]OUT Cb[9:0]OUT Output choices are the same as video out 16-/20-bit or pseudo 8-/10-bit DDR D7 D9 D7 D6 D8 D6 D5 D7 D5 D4 D6 D4 D3 D5 D3 D2 D4 D2 D1 D3 D1 CHA[7:0]OUT (for example, Y[7:0]) D0 D2 D0 D1 - D0 - - - CHA[9:0]OUT (for example, Y[9:0]) CHA[7:0]OUT (for example, G[7:0]) D11 D10 D9 D8 - - - CHB/C[7:0]OUT (for example, Cr/Cb[7:0]) - CHB/C[9:0]OUT (for example, Cr/Cb[9:0]) - - CHA[9:0]OUT (for example, G[9:0]) CHB[7:0]OUT (for example, B[7:0]) CHB[9:0]OUT (for example, B[9:0]) CHA[7:0]OUT (for example, Y[7:0]) R[5:4]IN CHB/C[7:0]OUT (for example, Cr/Cb[7:0]) CHA[7:0]OUT (for example, Y[7:0]) - CHB/C[7:0]OUT (for example, Cr/Cb[7:0]) CHA[9:0]OUT (for example, Y[9:0]) Rev. SpA | Page 17 of 24 - CHB/C[9:0]OUT (for example, Cr/Cb[9:0]) R[1:0]IN - - ADV7403 Table 10. SDP, CP Pixel Input/Output Pin Map (P40 to P20) Processor, Format, and Mode SDP Video out, 8-bit, 4:2:2 SDP Video out, 10-bit, 4:2:2 SDP Video out, 16-bit, 4:2:2 SDP Video out, 20-bit, 4:2:2 SDP Video out, 24-bit, 4:4:4 SDP Video out, 30-bit, 4:4:4 SM-SDP Digital tuner input[1] CP 8-bit, 4:2:2, DDR Pixel Port Pins P[40:31], P[29:20] 33 32 31 29 28 27 26 - 40 - 39 - 38 - 37 - 36 - 35 - 34 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Cr[7:0]OUT - - - - - - - - - - Cr[9:0]OUT DCVBS[9:0]IN 25 - 24 - 23 - 22 - 21 - 20 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - CP 10-bit, 4:2:2, DDR - - - - - - - - - - - - - - - - - - - - CP 12-bit, 4:4:4, RGB DDR Video out, 16-bit, 4:2:2 Video out, 20-bit, 4:2:2 Video out, 24-bit, 4:4:4 input Video out, 30-bit, 4:4:4 input HDMI receiver support, 24-bit, 4:4:4 input HDMI receiver support, 16-bit, pass-through HDMI receiver support, 20-bit, pass-through - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - CHC[7:0]OUT (for example, R[7:0]) - - - - - - - - - - - - CHC[9:0]OUT (for example, R[9:0]) CP CP CP CP SM-CP SM-CP SM-CP G[7:0]IN R[7:6]IN CHA[7:0]IN(for example, Y[7:0]) - CHA[9:0]IN(for example, Y[9:0]) Rev. SpA | Page 18 of 24 - B[7:0]IN CHB/C[7:0]IN(for example, Cr/Cb[7:0]) CHB/C[9:0]IN(for example, Cr/Cb[9:0]) R[3:2]IN - - ADV7403 RECOMMENDED EXTERNAL LOOP FILTER COMPONENTS The external loop filter components for the ELPF pin should be placed as close as possible to the respective pins. Figure 8 shows the recommended component values. PIN 46–ELPF 1.69kΩ 10nF PVDD = 1.8V 05431-007 82nF Figure 8. ELPF Components Rev. SpA | Page 19 of 24 Rev. SpA | Page 20 of 24 05431-009 RGB GRAPHICS F_BLNK BLUE GREEN RED/C 3 1LOAD AGND 2 4 Y C AGND 19Ω AGND 0.1 μF 0.1μF 0.1μF 0.1μF 0.1μF 0.1μF 0.1μF 0.1μF 0.1μF AGND 10nF Y 19Ω 75Ω Pb/Pr 75Ω 0.1μF 75Ω 0.1μF 75Ω Pr/Pb 56Ω CAP VALUES ARE DEPENDANT ON CRYSTAL ATTRIBUTES 56Ω 1 2 3 4 0.1μF MINI-DIN-4 1 P7 1 2 3 4 5 6 20 CVBS/Y 16 2 11 15 75Ω PHONO3 AGND RED S-VIDEO 19 17 15 13 11 9 7 5 3 1 75Ω GREEN BLUE CVBS 19Ω P9 P8 20 18 16 14 12 10 8 6 4 2 21 P4 SCART_21_PIN P5–14 P6–5 P6–6 P5–7 P5–8 P5–10 HS_IN VS_IN P5–13 P5–1 P5–3 P5–2 75Ω AGND 75Ω 0.1 μF 75Ω 0.1μF AGND 10nF AGND AGND 0.1 μF Y2 SDA 10nF 47pF1 RESET SCLK 47pF1 1MΩ 0.1 μF 0.1 μF C22 1nF + 10 μF 1nF D1 BZX399-C3V3 100Ω 100Ω 1.69kΩ 82nF PVDD_1.8V AGND + 10 μF C94 10nF DGND 0.1 μF U1 BYPASS CAPACITORS 10nF DVDD_1.8V 0.1 μF 28.63636MHz 10nF 10nF DGND 0.1 μF DVDDIO 10 μF 5.6kΩ 0.1 μF 10 μF 10nF 0.1 μF 0.1 μF DGND 0.1 μF 10nF U1 BYPASS CAPACITORS 2.7k Ω DVDDIO AIN4 AIN5 AIN6 SOY SOG AIN1 AIN2 AIN3 ELPF RESET 59 TEST1 51 FB 78 19 SDA2 16 SCLK2 80 ALSB 81 SDA 82 SCLK 46 38 XTAL 37 XTAL1 65 CML 64 REFOUT 67 BIAS 62 CAPY2 61 CAPY1 10nF DVDD_1.8V AVDD_3.3V PVDD_1.8V 69 CAPC2 68 CAPC1 53 AIN7 55 AIN8 57 AIN9 71 AIN10 73 AIN11 75 AIN12 72 74 76 77 52 54 56 58 U1 0.1 μF AGND 100Ω 100Ω 100Ω 100Ω 100Ω 100Ω 33Ω 36 HS 4 VS 99 FIELD 98 HREF/HS_IN 86 VREF/VS_IN 85 15 LLC1 DGND BAT54C K2 10kΩ DVDDIO VP19 VP18 VP17 VP16 VP15 VP14 VP13 VP12 VP11 VP10 VP09 VP08 VP07 VP06 VP05 VP04 VP03 VP02 VP01 VP00 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 91 92 93 94 7 8 9 10 20 21 22 23 25 26 27 28 41 42 43 44 P19 P18 P17 P16 P15 P14 P13 P12 P11 P10 P9 P8 P7 P6 P5 P4 P3 P2 P1 P0 VP29 VP28 VP27 VP26 VP25 VP24 VP23 VP22 VP21 VP20 K1 VP41 VP40 VP39 VP38 VP37 VP36 VP35 VP34 VP33 VP32 VP31 VP30 VP[00:41] SFL/SYNC_OUT HS VS FIELD HS_IN VS_IN LLC1 INT DCLCK_IN 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 33Ω 35 79 83 84 87 88 95 96 97 100 1 2 3 13 14 24 29 30 31 32 33 34 45 P29 P28 P27 P26 P25 P24 P23 P22 P21 P20 DCLK_IN DE_IN P40 P39 P38 P37 P36 P35 P34 P33 P32 P31 INT DVDDIO SFL/SYNC_OUT ADV7403 AVDD 63 49 PVSS 50 PVSS PVDD_1.8V 2.7k Ω DVDD 12 DVDD 39 90 DVDD 5 DVSSIO 17 DVSSIO 6 DVDDIO 18 DVDDIO AVDD_3.3V 47 PVDD PVDD 48 70 TEST0 66 AVSS 60 AVSS Figure 9. ADV7403 Typical Connection Diagram 11 DVSS 40 DVSS 89 DVSS U1 BYPASS CAPACITORS ADV7403 TYPICAL CONNECTION DIAGRAM ADV7403 OUTLINE DIMENSIONS 16.20 16.00 SQ 15.80 1.60 MAX 0.75 0.60 0.45 100 1 76 75 PIN 1 14.20 14.00 SQ 13.80 TOP VIEW (PINS DOWN) 0.15 0.05 SEATING PLANE 0.20 0.09 7° 3.5° 0° 0.08 COPLANARITY 51 50 25 26 VIEW A 0.50 BSC LEAD PITCH VIEW A ROTATED 90° CCW 0.27 0.22 0.17 COMPLIANT TO JEDEC STANDARDS MS-026-BED 051706-A 1.45 1.40 1.35 Figure 10. 100-Lead Low Profile Quad Flat Package [LQFP] (ST-100) Dimensions shown in millimeters ORDERING GUIDE Model1 ADV7403BSTZ-1102 ADV7403KSTZ-1402 EVAL-ADV7403EBM Temperature Range −40°C to +85°C 0°C to 70°C Package Description 100-Lead Low Profile Quad Flat Package (LQFP) 100-Lead Low Profile Quad Flat Package (LQFP) Evaluation board 1 Package Option ST-100 ST-100 The ADV7403 is a Pb-free, environmentally friendly product. It is manufactured using the most up-to-date materials and processes. The coating on the leads of each device is 100% pure Sn electroplate. The device is suitable for Pb-free applications, and is able to withstand surface-mount soldering at up to 255°C (±5°C). In addition, it is backward-compatible with conventional SnPb soldering processes. This means that the electroplated Sn coating can be soldered with SnPb solder pastes at conventional reflow temperatures of 220°C to 235°C. 2 Z = Pb-free part. Rev. SpA | Page 21 of 24 ADV7403 NOTES Rev. SpA | Page 22 of 24 ADV7403 NOTES Rev. SpA | Page 23 of 24 ADV7403 NOTES Purchase of licensed I2C components of Analog Devices or one of its sublicensed Associated Companies conveys a license for the purchaser under the Philips I2C Patent Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips. © 2005 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D05431–0–9/05(SpA) Rev. SpA | Page 24 of 24