Ultralow Power SD Video Filter with Load Detection ADA4431-1 Portable media players Portable gaming consoles Cell phones Digital still cameras Portable DVD players Portable video cameras 13 SAG 14 OUT 15 FB2 +VS 1 12 GND LOAD DETECT IN 2 11 SUBS LPF DIS 3 LDO 4 G=2 10 +VS 9 CAP1 06734-001 CAP2 8 CAP3 6 GND 7 CHARGE PUMP Figure 1. +VS 0.1µF 1 4 SYSTEM CONTROLLER VIDEO DAC/ ENCODER 3 2 7 +VS LDO +VS FB1 ADA4431-1 DIS IN 0.1µF 10 x1 LPF FB2 x2 OUT SAG GND 16 15 14 75Ω VIDEO OUT 13 CAP4 CAP3 CAP2 CAP1 SUBS GND 5 6 0.1µF 8 9 11 0.1µF 12 1.0µF 06734-002 APPLICATIONS PIN CONFIGURATION CAP4 5 Third-order, low-pass video filter 1 dB flatness out to 6 MHz 27 dB rejection at 27 MHz Low quiescent current: 4.7 mA typical Low power-down current: 24 μA typical Load detection capability SAG correction Allows use of smaller capacitors in ac-coupled outputs Low supply voltage: 2.5 V to 3.6 V Charge pump Creates a negative voltage from single positive supply Allows capless output coupling with no dc offset Rail-to-rail output High input-to-output isolation in disabled state 89 dB @ 1 MHz Small package 3 mm × 3 mm LFCSP Low 0.55 mm package height Wide operating temperature range: −40°C to +85°C 16 FB1 FEATURES Figure 2. Typical Application Circuit GENERAL DESCRIPTION The ADA4431-1 is a fully integrated video reconstruction filter that combines excellent video specifications with low power consumption, making it ideal for portable video filtering applications. The ADA4431-1 is able to detect whether a video load is present at the output, powering down the device when the load is disconnected. The ADA4431-1 operates on single supplies as low as 2.5 V while providing the dynamic range required by the most demanding video systems. The on-board charge pump provides a virtual negative supply, allowing the video signal to be dc-coupled and the black level to be set to ground, while the sync passes cleanly at 300 mV below ground. When operating with the charge pump off, the ADA4431-1 provides a dc offset to keep the sync tip approximately 100 mV above ground. In addition, the part features SAG correction, which permits the use of smaller capacitors in applications with ac-coupled outputs. The ADA4431-1 is packaged in a low profile 16-lead LFCSP and operates in the industrial temperature range of −40°C to +85°C. Rev. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2007 Analog Devices, Inc. All rights reserved. ADA4431-1 TABLE OF CONTENTS Features .............................................................................................. 1 Pin Configuration and Function Descriptions..............................6 Applications....................................................................................... 1 Typical Performance Characteristics ..............................................7 Pin Configuration............................................................................. 1 Theory of Operation .........................................................................9 General Description ......................................................................... 1 Overview ........................................................................................9 Revision History ............................................................................... 2 Charge Pump Operation ..............................................................9 Specifications..................................................................................... 3 Load Detect ....................................................................................9 Absolute Maximum Ratings............................................................ 5 Evaluation Board ............................................................................ 10 Thermal Resistance ...................................................................... 5 Outline Dimensions ....................................................................... 12 Maximum Power Dissipation ..................................................... 5 Ordering Guide .......................................................................... 12 ESD Caution.................................................................................. 5 REVISION HISTORY 8/07—Revision 0: Initial Version Rev. 0 | Page 2 of 12 ADA4431-1 SPECIFICATIONS VS = 3.0 V (@ TA = 25°C, VIN = 1 V p-p, RL = 150 Ω, DIS = 3.0 V, charge pump on), unless otherwise noted. Table 1. Parameter ELECTRICAL SPECIFICATIONS Quiescent Supply Current Normal Mode Load Searching Mode Disabled Mode Disable Pin Current Supply Voltage Range Input Voltage Input Resistance Input Capacitance Output Voltage Range Output Offset Voltage Power Supply Rejection Pass-Band Gain Input-to-Output Isolation—Disabled FILTER CHARACTERISTICS −3 dB Bandwidth 1 dB Flatness Out-of-Band Rejection Differential Gain Differential Phase Linear Output Current Group Delay Variation Test Conditions/Comments Min Video load present No video load DIS = 0 V DIS = 3.0 V (enabled and charge pump on) DIS = 0 V (disabled) Typ Max Unit 4.7 0.1 24 3 −17 7.2 mA mA μA μA μA V V MΩ pF V mV dB dB dB 2.5 Limited by output range f = 100 kHz, output referred −650 36 5.7 f = 1 MHz, DIS = 0 V 7.1 f = 27 MHz Modulated 10 step ramp, sync tip at 0 V Modulated 10 step ramp, sync tip at 0 V f = 100 kHz to 5 MHz Rev. 0 | Page 3 of 12 25 1.3 10 1 −0.8 to +2.8 −600 42 6.0 89 7.9 6 27 0.7 0.3 40 30 6 −30 3.6 −560 6.2 9.1 MHz MHz dB % Degrees mA ns ADA4431-1 VS = 3.0 V (@ TA = 25°C, VIN = 1 V p-p, RL = 150 Ω, DIS = floating, charge pump off), unless otherwise noted. Table 2. Parameter ELECTRICAL SPECIFICATIONS Quiescent Supply Current Normal Mode Load Searching Mode Disabled Mode Disable Pin Current Supply Voltage Range Input Voltage Input Resistance Input Capacitance Output Voltage Range Output Offset Voltage Power Supply Rejection Pass-Band Gain Input-to-Output Isolation—Disabled FILTER CHARACTERISTICS −3 dB Bandwidth 1 dB Flatness Out-of-Band Rejection Differential Gain Differential Phase Linear Output Current Group Delay Variation Test Conditions/Comments Min Video load present No video load DIS = 0 V DIS = 0 V Typ Max Unit 1.6 0.1 24 −17 2.2 mA mA μA μA V V MΩ pF V V dB dB dB 2.5 Limited by output range f = 100 kHz, output referred 38 5.8 f = 1 MHz, DIS = 0 V 6.7 f = 27 MHz Modulated 10 step ramp, sync tip at 0 V Modulated 10 step ramp, sync tip at 0 V f = 100 kHz to 5 MHz Rev. 0 | Page 4 of 12 26 1.3 10 1 0 to 2.8 0.1 48 6.0 89 7.5 6 29 0.4 0.3 40 30 −30 3.6 0.2 6.2 8.4 MHz MHz dB % Degrees mA ns ADA4431-1 ABSOLUTE MAXIMUM RATINGS Table 3. Parameter Supply Voltage Power Dissipation Storage Temperature Range Operating Temperature Range Lead Temperature (Soldering 10 sec) Junction Temperature Rating 4.0 V See Figure 3 –65°C to +125°C –40°C to +85°C 300°C 150°C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. The power dissipated in the package (PD) is the sum of the quiescent power dissipation and the power dissipated in the package due to the load drive. The quiescent power is the voltage between the supply pins (VS) times the quiescent current (IS). The power dissipated due to the load drive depends upon the particular application. The power due to load drive is calculated by multiplying the load current by the associated voltage drop across the device. RMS voltages and currents must be used in these calculations. Airflow increases heat dissipation, effectively reducing θJA. In addition, more metal directly in contact with the package leads and exposed pad from metal traces, through-holes, ground, and power planes reduces the θJA. Figure 3 shows the maximum safe power dissipation in the package vs. the ambient temperature for the 16-lead LFCSP package (43°C/W) on a JEDEC standard 4-layer board. THERMAL RESISTANCE 5.0 Table 4. Thermal Resistance Package Type 16-lead LFCSP-UQ (CP-16-12) θJA 43 Unit °C/W 4.5 4.0 3.5 3.0 2.5 2.0 MAXIMUM POWER DISSIPATION 1.5 The maximum safe power dissipation in the ADA4431-1 package is limited by the associated rise in junction temperature (TJ) on the die. At approximately 150°C, which is the glass transition temperature, the plastic changes its properties. Even temporarily exceeding this temperature limit can change the stresses that the package exerts on the die, permanently shifting the parametric performance of the ADA4431-1. Exceeding a junction temperature of 150°C for an extended period can result in changes in the silicon devices potentially causing failure. 1.0 –40 –30 –20 –10 0 10 20 30 40 50 60 AMBIENT TEMPERATURE (°C) 70 80 90 100 06743-003 MAXIMUM POWER DISSIPATION (W) θJA is specified for the device (including exposed pad) soldered to a high thermal conductivity 2s2p circuit board, as described in EIA/JESD 51-7. The exposed pad is not electrically connected to the device. It is typically soldered to a pad on the PCB that is thermally and electrically connected to an internal ground plane. Figure 3. Maximum Power Dissipation vs. Temperature for a 4-Layer Board ESD CAUTION Rev. 0 | Page 5 of 12 ADA4431-1 14 OUT 13 SAG 16 FB1 15 FB2 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS 12 GND +VS 1 IN 2 ADA4431-1 11 SUBS DIS 3 TOP VIEW (Not to Scale) 10 +VS GND 7 CAP2 8 CAP4 5 CAP3 6 06743-004 9 CAP1 LDO 4 Figure 4. Pin Configuration Table 5. Pin Function Descriptions Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Mnemonic +VS IN DIS LDO CAP4 CAP3 GND CAP2 CAP1 +VS SUBS GND SAG OUT FB2 FB1 Description Supply Voltage. Video Input. Disable Pin. High = charge pump on, floating = charge pump off, low = disabled. Load Detect Output. High = video load present. Capacitor 2, Lead 2. Capacitor 2, Lead 1. Ground. Capacitor 1, Lead 2. Capacitor 1, Lead 1. Supply Voltage. Substrate Voltage Pin. Bypass to GND with 1.0 μF capacitor. Ground. SAG Feedback Pin. Video Output. Load Detect Feedback Pin 2. Connect to device side of series termination resistor. Load Detect Feedback Pin 1. Connect to load side of series termination resistor. Rev. 0 | Page 6 of 12 ADA4431-1 TYPICAL PERFORMANCE CHARACTERISTICS VS = 3.0 V (@ TA = 25°C, VIN = 1 V p-p, RL = 150 Ω, unless otherwise noted). 10 60 CHARGE PUMP ON 0 50 GROUP DELAY (ns) NORMALIZED GAIN (dB) –10 –20 –30 CHARGE PUMP OFF –40 40 30 CHARGE PUMP OFF 20 –50 10 –60 10 100 FREQUENCY (MHz) 1 100 100 FREQUENCY (MHz) Figure 5. Large Signal Frequency Response Figure 8. Group Delay vs. Frequency 1 0 CHARGE PUMP ON –5 0 VIN = 100mV p-p DIS = 3V –10 CHARGE PUMP ON –15 –1 PSRR (dB) NORMALIZED GAIN (dB) 10 06734-008 1 06734-005 0.1 0 0.1 06734-009 CHARGE PUMP ON –70 –2 CHARGE PUMP OFF –3 –20 CHARGE PUMP OFF –25 –30 –35 –40 –4 –45 1 10 FREQUENCY (MHz) –50 0.1 06734-006 –5 0.1 1 10 FREQUENCY (MHz) Figure 6. Frequency Response Flatness Figure 9. PSRR vs. Frequency –60 10 +85°C +25°C 0°C –40°C DIS = 0V –65 0 NORMALIZED GAIN (dB) –75 –80 –85 –90 –10 –20 –30 –40 –95 –105 0.1 1 10 FREQUENCY (MHz) 100 –60 0.1 1 10 100 FREQUENCY (MHz) Figure 7. Input-to-Output Isolation vs. Frequency Figure 10. Frequency Response for Various Temperatures Rev. 0 | Page 7 of 12 06734-010 –50 –100 06734-007 NORMALIZED GAIN (dB) –70 ADA4431-1 1 T NORMALIZED GAIN (dB) 0 +85°C +25°C 0°C –40°C –1 –2 –3 –4 2 –5 1 10 FREQUENCY (MHz) CH2 200mV Figure 11. Flatness Response for Various Temperatures M100ns A CH1 316mV 06734-015 –7 0.1 06734-011 –6 Figure 14. Transient Response 6 T SUPPLY CURRENT (mA) 5 4 DISABLE (DIS) PIN 1 3 OUTPUT 2 2 0.5 1.0 1.5 2.0 2.5 3.0 DISABLE (DIS) PIN VOLTAGE (V) CH1 2.00V Figure 12. Supply Current vs. Disable (DIS) Pin Voltage 7 50 4 40 3 30 DISABLED 2 20 1 10 0 –40 –30 –20 –10 0 10 20 30 40 50 60 70 80 TEMPERATURE (°C) 0 90 DISABLED SUPPLY CURRENT (µA) 5 A CH1 1.72V 1.72V T DISABLE (DIS) PIN 1 OUTPUT 2 06734-014 SUPPLY CURRENT (mA) 60 ACTIVE M10.0ms Figure 15. Output Enable 70 6 CH2 500mV 06734-016 0 06734-017 0 06734-012 1 Figure 13. Supply Current vs. Temperature CH1 2.00V CH2 500mV M40.0ns Figure 16. Output Disable Rev. 0 | Page 8 of 12 A CH1 ADA4431-1 THEORY OF OPERATION OVERVIEW The ADA4431-1 is designed for exceptional performance as both a filter and a low power driver for portable video applications. This performance is achieved by providing third-order filtering without trading off power consumption or device size. While consuming only 4.7 mA quiescent supply current, the ADA4431-1 provides video output on a single-supply as low as 2.5 V. The ADA4431-1 also features a load detect circuit, which senses current through the external 75 Ω back-termination resistor. When either no video load or a short circuit is detected, the ADA4431-1 enters a low power state. In this state, it draws 0.1 mA, continues to monitor the load current, and powers up automatically when a video load is connected. Optionally, the ADA4431-1 can be powered down via the disable pin (DIS). Another external pin (LDO) outputs the load detection state (for example, to an external system controller). This pin is high (+VS) when a video load is present, and low (0 V) in the absence of a video load or when the output is short-circuited. The ADA4431-1 is intended for use in applications that have both ac- and dc-coupled inputs and outputs. The rail-to-rail buffer on the ADA4431-1 output is able to drive 2 V p-p video signals into two doubly terminated video loads (150 Ω each) on a single 2.5 V supply. The ADA4431-1 has a gain of 2 when the SAG correction pin is tied directly to the output, which makes up for the 6 dB termination loss (see Figure 17, Output Option 1). When the SAG feature is used, the ADA4431-1 has a low frequency gain of 2.5 (≈8 dB) and a high frequency gain of 2 (see Figure 17, Output Option 2). Signal offsets and supply levels must be considered when using the SAG correction feature to ensure that there are no headroom issues. The input range of the ADA4431-1 includes ground, while the output range is limited by the saturation of the output devices. Saturation occurs several tens of mV from the positive and negative supply rails. The high input impedance and low input capacitance of the ADA4431-1 offer advantages in a number of low power applications. In reconstruction filter applications, the DAC can be placed in its lowest power mode, allowing the use of a largevalued load resistor. Using a large-valued load resistor does not interfere with the frequency response of the ADA4431-1. CHARGE PUMP OPERATION The on-board charge pump creates a virtual negative supply for the output driver, which allows the output signal to be dc-coupled, with its black level at 0 V and sync tip at −300 mV. The charge pump is enabled whenever the disable pin (DIS) is held high. If DIS is left floating, or placed in a high impedance state, the ADA4431-1 is powered up, but the charge pump is disabled, which is typically the case for ac-coupling of the output. When DIS is driven to 0 V, the entire device is powered down. Table 6. Disable (DIS) Pin Function Summary DIS Pin Low High High-Z Device State Disabled Enabled Enabled Charge Pump State Disabled Enabled Disabled LOAD DETECT The load detect feature provides additional system power management to keep the power consumption of a portable device to the absolute minimum. The ADA4431-1 monitors the output load for three conditions: a normal load, a shorted load, and an open load. Each of these conditions occurs for a video load, an audio load, and no load, respectively. Only in the video load condition will the ADA4431-1 power up from 0.1 mA to 4.7 mA. A single I/O pin, LDO, notifies the system by either being high for a video load or low for a short and open load. With this information, it is intended that the system controller power down any power intensive video processing blocks to realize substantial power savings. The ADA4431-1 operates autonomously, requiring no inputs to monitor the condition of the output load. Rev. 0 | Page 9 of 12 ADA4431-1 EVALUATION BOARD The ADA4431-1 evaluation board allows designers to assess the performance of the part in their particular application. The board includes input and output SMA coaxial connectors and 75 Ω-controlled impedance signal traces. Power (2.5 V to 3.6 V) is applied to the red V+ loop connector, and ground is connected to the black GND loop connector. Connecting the center pin to the GND position short circuits the output, causing the ADA4431-1 to power down, and the LDO pin to go low. If an external video load is connected to the OUT connector, the jumper should be removed. With the jumper removed, disconnecting the external load also causes the ADA4431-1 to power down. The output signal can be configured for dc coupling or ac coupling. When ac-coupled, two options are available: the standard single capacitor configuration (minimum of 220 μF) and the SAG-corrected configuration, using two smaller capacitors (47 μF and 22 μF). Jumper Block J4 exercises the disable pin (DIS). When a jumper is connected from the center pin to V+, the charge pump is enabled. Connecting the center pin to GND forces the ADA4431-1 into low power mode. With the jumper removed, the ADA4431-1 is enabled but the charge pump is disabled. Jumper Block J2 allows the load detect feature to be evaluated without connecting an external video load. Connecting a jumper from the center pin to the 75 position applies a 75 Ω load to the output and causes the LDO pin to go high. A schematic of the ADA4431-1 evaluation board, with output coupling options, is shown in Figure 17. Figure 18 and Figure 19 show the front and back layout of the evaluation board. R6 75Ω J2 OUTPUT OPTION 1 OUT R5 75Ω C5 0Ω OUT SAG 6 7 8 V+ OUTPUT OPTION 2 C5 47µF C6 0Ω + C1 0.1µF C2 0.1µF LDO 14 C8 + 10µF 13 C4 22µF AC-COUPLED OUTPUT WITH SAG CORRECTION V+ Figure 17. Evaluation Board Schematic Rev. 0 | Page 10 of 12 06734-018 LDOUT 5 C7 0.1µF SUBS + J4 GND DIS V+ R4 DNI C3 1.0µF 10 CAP1 9 GND R3 DNI +VS CAP2 4 LDO DIS ADA4431-1 3 DIS GND GND 12 SUBS 11 2 IN R2 75Ω LD2 DC-COUPLED 13 OUTPUT 14 FB2 1 +VS FB1 16 15 C9 0.1µF R1 0Ω C6 0Ω C4 0Ω V+ CAP3 AC-COUPLED 13 OUTPUT CAP4 C4 0Ω IN GND + C5 0Ω 14 75Ω C6 220µF Figure 18. Evaluation Board—Front 06743-020 06743-019 ADA4431-1 Figure 19. Evaluation Board—Back Rev. 0 | Page 11 of 12 ADA4431-1 OUTLINE DIMENSIONS 3.00 BSC SQ PIN 1 INDICATOR 13 12 16 1 1.80 1.70 SQ 1.55 EXPOSED PAD 0.50 BSC TOP VIEW 8 5 4 BOTTOM VIEW 0.60 0.55 0.51 SEATING PLANE 9 0.40 MAX 0.30 NOM 0.05 MAX 0.02 NOM 0.30 0.25 0.18 0.08 REF COMPLIANT TO JEDEC STANDARDS MO-248-UEED. 053106-B INDEX AREA Figure 20. 16-Lead Lead Frame Chip Scale Package [LFCSP_UQ] 3 mm × 3 mm Body, Ultra Thin Quad (CP-16-12) Dimensions shown in millimeters ORDERING GUIDE Model ADA4431-1YCPZ-R2 1 ADA4431-1YCPZ-R71 ADA4431-1YCPZ-RL1 1 Temperature Range −40°C to +85°C −40°C to +85°C −40°C to +85°C Package Description 16-Lead LFCSP_UQ 16-Lead LFCSP_UQ 16-Lead LFCSP_UQ Package Option CP-16-12 CP-16-12 CP-16-12 Branding H12 H12 H12 Ordering Quantity 250 3,000 10,000 Z = RoHS Compliant Part. ©2007 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D06734-0-8/07(0) T T Rev. 0 | Page 12 of 12