AD ADA4859-3ACPZ-R2

Single-Supply, Fixed G = 2, High Speed,
Video Amplifier with Charge Pump
ADA4859-3
FEATURES
CONNECTION DIAGRAM
OUT1
–IN1
+IN1
NC
ADA4859-3
16
15
14
13
12 +IN2
+VS 1
C1_b 3
11 –IN2
CHARGE
PUMP
10 OUT2
CPO 4
6
7
8
–IN3
OUT3
5
+IN3
9
NOTES
1. NC = NO CONNECT.
2. EXPOSED PAD, CONNECT TO GROUND.
PD
07715-001
C1_a 2
+VS
Integrated charge pump
Supply range: 3 V to 5.5 V
Output range: −3.3 V to −1.8 V
50 mA maximum output current at −3 V for external use
High speed amplifiers
−3 dB bandwidth: 195 MHz
Slew rate: 740 V/μs
0.1 dB gain flatness: 60 MHz
0.1% settling time: 20 ns
Low power
Total quiescent current: 38 mA
Power-down feature
High input common-mode voltage range
−1.8 V to +3.8 V at +5 V supply
Current feedback architecture
Differential gain error: 0.01%
Differential phase error: 0.02°
Available in 16-lead LFCSP
Figure 1.
APPLICATIONS
Professional video
Consumer video
Imaging
Active filters
GENERAL DESCRIPTION
The ADA4859-3 (triple) is a single-supply, high speed current
feedback amplifier with an integrated charge pump that eliminates
the need for negative supplies in order to output negative voltages
or output a 0 V level for video applications. The 195 MHz, large
signal −3 dB bandwidth at a fixed gain of 2, as well as the 740 V/μs
slew rate, make this amplifier ideal for high resolution professional
and consumer video applications. The amplifier also has a wide
input common-mode voltage range that extends from 1.8 V
below ground to 1.2 V below the positive rail at 5 V supply.
This triple video amplifier is designed to operate on supply
voltages of 3.3 V to 5 V, using only 38 mA total quiescent
current, including the charge pump. To further reduce the
power consumption, it is equipped with a power-down feature
that lowers the total supply current to as low as 2 mA when the
amplifier is not being used. Even in power-down mode, the
charge pump can be used to power external components. The
maximum output current for external use is 50 mA at −3 V.
The ADA4858-3 is available in a 16-lead LFCSP, and it is designed
to work over the industrial temperature range of −40°C to +105°C.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2008 Analog Devices, Inc. All rights reserved.
ADA4859-3
TABLE OF CONTENTS
Features .............................................................................................. 1 Theory of Operation ...................................................................... 12 Applications ....................................................................................... 1 Overview ..................................................................................... 12 Connection Diagram ....................................................................... 1 Charge Pump Operation ........................................................... 12 General Description ......................................................................... 1 Applications Information .............................................................. 13 Revision History ............................................................................... 2 Using the ADA4859-3 in Gains Equal to +1, −1........................ 13 Specifications..................................................................................... 3 Video Line Driver ....................................................................... 14 Absolute Maximum Ratings............................................................ 5 Power-Down ............................................................................... 14 Maximum Power Dissipation ..................................................... 5 Layout Considerations ............................................................... 14 ESD Caution .................................................................................. 5 Power Supply Bypassing ............................................................ 14 Pin Configuration and Function Descriptions ............................. 6 Outline Dimensions ....................................................................... 15 Typical Performance Characteristics ............................................. 7 Ordering Guide .......................................................................... 15 REVISION HISTORY
11/08—Revision 0: Initial Version
Rev. 0 | Page 2 of 16
ADA4859-3
SPECIFICATIONS
TA = 25°C, VS = 5 V, G = 2, RF = 550 Ω, RL = 150 Ω, unless otherwise noted.
Table 1.
Parameter
DYNAMIC PERFORMANCE
−3 dB Bandwidth
Bandwidth for 0.1 dB Flatness
Slew Rate
Settling Time to 0.1%
NOISE/DISTORTION PERFORMANCE
Harmonic Distortion (HD2/HD3)
Crosstalk
Total Output Noise
Input Current Noise
Differential Gain Error
Differential Phase Error
DC PERFORMANCE
Output Offset Voltage
+Input Bias Current
Closed-Loop Gain
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Input Common-Mode Voltage Range
OUTPUT CHARACTERISTICS
Output Voltage Swing
Output Overdrive Recovery Time
Maximum Linear Output Current @ VO = 1 VPEAK
POWER-DOWN
Input Voltage
Bias Current
Turn-On Time
Turn-Off Time
POWER SUPPLY
Operating Range
Total Quiescent Current
Amplifier
Charge Pump
Total Quiescent Current When Powered Down
Amplifier
Charge Pump
Positive Power Supply Rejection Ratio
Negative Power Supply Rejection Ratio
Charge Pump Output Voltage
Charge Pump Sink Current
Conditions
Min
Typ
Max
Unit
VOUT = 0.1 V p-p
VOUT = 2 V p-p
VOUT = 2 V p-p, CL = 6 pF
VOUT = 2 V step
VOUT = 2 V step
265
195
60
740
20
MHz
MHz
MHz
V/μs
ns
fC = 1 MHz, VO = 2 V p-p
fC = 5 MHz, VO = 2 V p-p
f = 5 MHz
f = 1 MHz
f = 1 MHz
−84/−93
−70/−83
−80
17
2
0.01
0.02
dBc
dBc
dBc
nV/√Hz
pA/√Hz
%
Degrees
−25
−2
1.9
+IN
+IN
+9
+0.7
2
+25
+2
2.1
mV
μA
V/V
+3.8
MΩ
pF
V
15
1.5
−1.8
−1.4 to +3.6
Rise/fall, f = 5 MHz
fC = 1 MHz, HD2 ≤ −50 dBc
−1.7 to +3.8
15
19
V
ns
mA
Enabled
Powered down
1.9
2
+0.1
V
V
μA
μs
μs
5.5
V
−0.1
0.5
2
3
15
17
21
21
mA
mA
0.15
0.25
4
−55
−51
−3
0.3
mA
mA
dB
dB
V
mA
Referred to output
Referred to output
−3.2
Rev. 0 | Page 3 of 16
−50
−47
−2.5
150
ADA4859-3
TA = 25°C, VS = 3.3 V, G = 2, RF = 550 Ω, RL = 150 Ω, unless otherwise noted.
Table 2.
Parameter
DYNAMIC PERFORMANCE
−3 dB Bandwidth
Bandwidth for 0.1 dB Flatness
Slew Rate
Settling Time to 0.1%
NOISE/DISTORTION PERFORMANCE
Total Harmonic Distortion
Crosstalk
Total Output Noise
Input Current Noise
Differential Gain Error
Differential Phase Error
DC PERFORMANCE
Output Offset Voltage
+Input Bias Current
Closed-Loop Gain
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Input Common-Mode Voltage Range
OUTPUT CHARACTERISTICS
Output Voltage Swing
Output Overdrive Recovery Time
Maximum Linear Output Current @ VO = 1 VPEAK
POWER-DOWN
Input Voltage
Bias Current
Turn-On Time
Turn-Off Time
POWER SUPPLY
Operating Range
Total Quiescent Current
Amplifier
Charge Pump
Total Quiescent Current When Powered Down
Amplifier
Charge Pump
Positive Power Supply Rejection Ratio
Negative Power Supply Rejection Ratio
Charge Pump Output Voltage
Charge Pump Sink Current
Conditions
Min
Typ
Max
Unit
VOUT = 0.1 V p-p
VOUT = 2 V p-p
VOUT = 2 V p-p, CL = 6 pF
VOUT = 2 V step, RL = 150 Ω
VOUT = 2 V step
260
165
65
530
20
MHz
MHz
MHz
V/μs
ns
fC = 1 MHz, VO = 2 V p-p
fC = 5 MHz, VO = 2 V p-p
f = 5 MHz
f = 1 MHz
f = 1 MHz
−84/−86
−73/−77
−80
17
2
0.02
0.03
dBc
dBc
dBc
nV/√Hz
pA/√Hz
%
Degrees
−25
−2
1.9
+IN
+IN
+9
+0.7
2
+25
+2
2.1
mV
μA
V/V
+2.2
MΩ
pF
V
15
1.5
−0.9
Rise/fall, f = 5 MHz
fC = 1 MHz, HD2 ≤ −50 dBc
−0.7 to +2.1
−1 to +2.3
15
18
V
ns
mA
Enabled
Powered down
1.25
1.35
+0.1
V
V
μA
μs
μs
5.5
V
−0.1
0.5
2
3
14
17
19
20
mA
mA
0.15
0.25
2
−54
−50
−2
0.3
mA
mA
dB
dB
V
mA
Referred to output
Referred to output
−2.1
Rev. 0 | Page 4 of 16
−50
−47
−1.8
45
ADA4859-3
ABSOLUTE MAXIMUM RATINGS
MAXIMUM POWER DISSIPATION
Table 3.
See Figure 2
(−VS − 0.2 V) to (+VS − 1.8 V)
±VS
Observe power derating curves
−65°C to +125°C
−40°C to +105°C
300°C
The maximum power that can be safely dissipated by the
ADA4859-3 is limited by the associated rise in junction
temperature. The maximum safe junction temperature
for plastic encapsulated devices is determined by the glass
transition temperature of the plastic, approximately 150°C.
Temporarily exceeding this limit may cause a shift in parametric
performance due to a change in the stresses exerted on the die
by the package. Exceeding a junction temperature of 175°C for
an extended period can result in device failure.
To ensure proper operation, it is necessary to observe the
maximum power derating curves in Figure 2.
2.5
Specification is for device in free air.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
MAXIMUM POWER DISSIPATION (W)
1
Rating
6V
2.0
1.5
1.0
0.5
0
–40
–20
0
20
40
60
80
100
AMBIENT TEMPERATURE (°C)
Figure 2. Maximum Power Dissipation vs. Ambient Temperature
ESD CAUTION
Rev. 0 | Page 5 of 16
07715-002
Parameter
Supply Voltage
Internal Power Dissipation1
16-Lead LFCSP
Input Voltage (Common-Mode)
Differential Input Voltage
Output Short-Circuit Duration
Storage Temperature Range
Operating Temperature Range
Lead Temperature
(Soldering, 10 sec)
ADA4859-3
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
ADA4859-3
OUT1
–IN1
+IN1
NC
TOP VIEW
(Not to Scale)
16
15
14
13
12 +IN2
+VS 1
C1_b 3
11 –IN2
CHARGE
PUMP
10 OUT2
CPO 4
6
7
8
–IN3
OUT3
+VS
5
+IN3
9
NOTES
1. NC = NO CONNECT.
2. EXPOSED PAD, CONNECT TO GROUND.
PD
07715-003
C1_a 2
Figure 3. Pin Configuration
Table 4. Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17 (EPAD)
Mnemonic
+VS
C1_a
C1_b
CPO
+VS
+IN3
−IN3
OUT3
PD
OUT2
−IN2
+IN2
NC
+IN1
−IN1
OUT1
Exposed Pad (EPAD)
Description
Positive Supply for Charge Pump.
Charge Pump Capacitor Side a.
Charge Pump Capacitor Side b.
Charge Pump Output.
Positive Supply.
Noninverting Input 3.
Inverting Input 3.
Output 3.
Power Down.
Output 2.
Inverting Input 2.
Noninverting Input 2.
No Connect.
Noninverting Input 1.
Inverting Input 1.
Output 1.
The exposed pad must be connected to the ground plane.
Rev. 0 | Page 6 of 16
ADA4859-3
TYPICAL PERFORMANCE CHARACTERISTICS
2
1
1
0
–1
–2
–3
–4
VS = 5V
–6
–7
VS = 3.3V
–8
1
10
100
1000
FREQUENCY (MHz)
–4
VS = 5V
–5
–6
–7
VS = 3.3V
1
10
100
Figure 7. Large Signal Frequency Response vs. Supply Voltage
0.2
0.2
0.1
0.1
CL = 10pF
0
NORMALIZED GAIN (dB)
0
–0.1
–0.2
–0.3
–0.4
–0.5
–0.6
1
10
100
1000
FREQUENCY (MHz)
–0.3
CL = 14pF
–0.4
–0.5
1
10
100
1000
FREQUENCY (MHz)
Figure 8. Large Signal 0.1 dB Flatness vs. Capacitive Load
0
–10
–10
–20
–20
–30
–30
DISTORTION (dBc)
0
–40
HD2
–60
–70
–80
CL = 10pF
–0.8
Figure 5. Large Signal 0.1 dB Flatness vs. Supply Voltage
–50
CL = 16pF
–0.2
–0.7
VS = 3.3V
–0.8
–0.1
–0.6
VS = 5V
–0.7
1000
FREQUENCY (MHz)
07715-005
VS = 3.3V
–40
–50
HD2
–60
–70
HD3
–80
HD3
–90
–100
1
10
FREQUENCY (MHz)
100
07715-006
–90
Figure 6. Harmonic Distortion vs. Frequency
–100
1
10
FREQUENCY (MHz)
Figure 9. Harmonic Distortion vs. Frequency
Rev. 0 | Page 7 of 16
100
07715-009
NORMALIZED CLOSED-LOOP GAIN (dB)
–3
–8
Figure 4. Small Signal Frequency Response vs. Supply Voltage
DISTORTION (dBc)
–2
07715-008
–5
0
–1
07715-007
NORMALIZED CLOSED-LOOP GAIN (dB)
2
07715-004
NORMALIZED CLOSED-LOOP GAIN (dB)
VS = 5 V, G = 2, RF = 550 Ω, RL = 150 Ω, large signal VOUT = 2 V p-p, small signal VOUT = 0.1 V p-p, and T = 25ºC, unless otherwise noted.
ADA4859-3
0
0.2
0.1
–10
CL = 16pF
NORMALIZED GAIN (dB)
0
PSRR (dB)
–20
–30
–40
–50
–0.1
CL = 10pF
–0.2
CL = 110pF
CL = 14pF
–0.3
–0.4
–0.5
–0.6
–60
–0.7
10
100
400
FREQUENCY (MHz)
1
100
1000
FREQUENCY (MHz)
Figure 10. Power Supply Rejection Ratio (PSRR) vs. Frequency
Figure 13. Large Signal 0.1 dB Flatness vs. Capacitive Load
–40
–30
–40
–50
–50
–60
CROSSTALK (dB)
–70
–80
–60
–70
–80
–90
–90
1
10
100
400
FREQUENCY (MHz)
–100
0.1
07715-011
–100
0.1
1
10
100
400
FREQUENCY (MHz)
Figure 11. Forward Isolation vs. Frequency
07715-014
FORWARD ISOLATION (dB)
10
07715-013
1
VS = 3.3V
–0.8
07715-010
–70
0.1
Figure 14. Crosstalk vs. Frequency
250
20
INPUT CURRENT NOISE (pA/ Hz)
200
150
100
50
16
14
12
10
8
6
4
0
100
1k
10k
100k
FREQUENCY (Hz)
1M
Figure 12. Total Output Voltage Noise vs. Frequency
0
100
1k
10k
100k
1M
FREQUENCY (Hz)
Figure 15. Noninverting Input Current Noise vs. Frequency
Rev. 0 | Page 8 of 16
07715-015
2
07715-012
OUTPUT VOLTAGE NOISE (nV/ Hz)
18
ADA4859-3
1.5
VOUT = 200mV p-p
CL = 10pF
1.0
CL = 4pF
OUTPUT VOLTAGE (V)
0.05
0
–0.05
CL = 4pF
0.5
0
–0.5
–1.0
CL = 6pF
07715-016
CL = 10pF
–0.15
TIME (5ns/DIV)
–1.5
TIME (5ns/DIV)
Figure 16. Small Signal Transient Response vs. Capacitive Load
Figure 19. Large Signal Transient Response vs. Capacitive Load
1.5
VOUT = 200mV p-p
0.05
0
–0.05
VS = 5V
–0.10
TIME (5ns/DIV)
1.5
VS = 5V
0.5
1.0
0
07715-017
VS = 3.3V
–0.15
1.0
OUTPUT VOLTAGE, VS = 5V (V)
0.10
OUTPUT VOLTAGE (V)
2.0
VS = 3.3V
0.5
–0.5
0
–1.0
–0.5
–1.5
–1.0
TIME (5ns/DIV)
Figure 17. Small Signal Transient Response vs. Supply Voltage, CL = 4 pF
Figure 20. Large Signal Transient Response vs. Supply Voltage, CL = 4 pF
1100
900
1000
VS = 3.3V
800
RISE
900
700
800
SLEW RATE (V/µs)
RISE
700
FALL
600
500
400
600
FALL
500
400
300
300
200
200
100
0
0.5
1.0
1.5
2.0
OUTPUT VOLTAGE (V p-p)
2.5
07715-018
SLEW RATE (V/µs)
OUTPUT VOLTAGE, VS = 3.3V (V)
0.15
07715-019
–0.10
Figure 18. Slew Rate vs. Output Voltage
100
0
0.5
1.0
1.5
2.0
OUTPUT VOLTAGE (V p-p)
Figure 21. Slew Rate vs. Output Voltage
Rev. 0 | Page 9 of 16
2.5
07715-021
OUTPUT VOLTAGE (V)
0.10
CL = 6pF
07715-020
0.15
ADA4859-3
2.5
2.0
3
1.5
2
1.0
1
0.5
0
0
1.5
VIN
VS = 3.3V
2.5
1.0
OUTPUT VOLTAGE (V)
INPUT VOLTAGE (V)
–0.5
–1
0.5
1.0
0.5
0
0
–0.5
–1.0
–0.5
–1.5
–3
VOUT
–1.5
TIME (20ns/DIV)
–1.0
–2.0
TIME (20ns/DIV)
Figure 22. Output Overdrive Recovery
Figure 25. Output Overdrive Recovery
2.0
0.5
1.6
0.4
0.3
1.2
0.3
0.8
0.2
0.8
0.4
0.1
0
0
–0.1
–0.4
ERROR
–0.8
–1.2
–0.3
–1.2
–1.6
–0.4
–1.6
10
15
20
25
30
35
–0.5
40
TIME (ns)
–0.1
–0.4
0
16
AMPLIFIER
CURRENT
14
–2.4
12
OUTPUT
VOLTAGE
–2.8
–3.2
2.5
OUTPUT VOLTAGE (V)
–1.6
3.0
3.5
4.0
10
4.5
20
25
30
35
–0.5
40
8
5.0
CHARGE PUMP SUPPLY VOLTAGE (V)
6
VPD
5
VOUT
CURRENT (mA)
18
–2.0
1.0
20
–1.2
15
1.5
07715-024
CHARGE PUMP OUTPUT VOLTAGE (V)
–0.8
10
TIME (ns)
22
CHARGE
PUMP CURRENT
5
Figure 26. Settling Time, (Fall)
24
–0.4
–0.3
OUTPUT
Figure 23. Settling Time (Rise)
0
–0.2
INPUT
–2.0
–5
07715-023
5
0
–0.4
–0.2
0
0.1
0
–0.8
–2.0
–5
0.2
ERROR
0.4
ERROR (%)
INPUT
ERROR (%)
OUTPUT
AMPLITUDE (V)
0.4
1.2
1.6
AMPLITUDE (V)
0.5
07715-026
2.0
0.5
4
0
3
–0.5
2
–1.0
1
–1.5
Figure 24. Charge Pump Voltage and Current vs. Supply Voltage
0
TIME (400ns/DIV)
Figure 27. Enable/Power-Down Time
Rev. 0 | Page 10 of 16
POWER-DOWN VOLTAGE (V)
–2
1.5
–1.0
VOUT
07715-022
OUTPUT VOLTAGE (V)
2.0
INPUT VOLTAGE (V)
4
3.0
07715-025
VIN
07715-027
5
ADA4859-3
–100
–110
–110
–115
–115
POWER (dBm)
–105
–120
–125
–130
–120
–125
–130
–135
–135
–140
–140
–145
–145
–150
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
VS = 3.3V
CHARGE PUMP HARMONICS
–105
4.0
FREQUENCY (MHz)
4.5
5.0
–150
07715-100
POWER (dBm)
CHARGE PUMP HARMONICS
Figure 28. Output Spectrum vs. Frequency
Rev. 0 | Page 11 of 16
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
FREQUENCY (MHz)
Figure 29. Output Spectrum vs. Frequency
4.5
5.0
07715-101
–100
ADA4859-3
THEORY OF OPERATION
OVERVIEW
Φ1
+VS
CHARGE PUMP OPERATION
The on-board charge pump creates a negative supply for the
amplifier. It provides different negative voltages depending on
the power supply voltage. For a +5 V supply, the negative supply
generated is equal to −3 V with 150 mA of output supply current,
and for a +3.3 V supply, the negative supply is equal to −2 V
with 45 mA of output supply current.
Figure 30 shows the charging cycle when the supply voltage,
+VS, charges C1 through Φ1 to ground. During this cycle, C1
quickly charges to reach the +VS voltage. The discharge cycle then
begins with switching Φ1 off and switching Φ2 on, as shown in
Figure 31. When C1 = C2, the charge in C1 is divided between
the two capacitors and slowly increases the voltage in C2 until it
reaches a predetermined voltage (−3 V for the +5 V supply and
−2 V
for the +3.3 V supply). The typical charge pump charging and
discharging frequency is 550 kHz with a 150 Ω load and no input
signal. This frequency changes with the load current, and it can
get much slower if the amplifier is powered down and no external
current is used.
CPO
b
C2
Φ1
07715-137
C1
The ADA4859-3 is a fixed gain of two, current feedback amplifier
designed for exceptional performance as a triple video amplifier. Its
specifications make it especially suitable for SD and HD video
applications. The ADA4859-3 provides HD video output on a
single supply as low as 3.0 V while only consuming 13 mA per
amplifier. It also features a power-down pin (PD) that reduces
the quiescent current to 4 mA when activated.
Figure 30. Charging Cycle
a
+VS
Φ2
C1
CPO
C2
Φ2
b
07715-138
The ADA4859-3 can be used in applications that require both
ac- and dc-coupled inputs and outputs. The output stage on the
ADA4859-3 is capable of driving 2 V p-p video signals into two
doubly terminated video loads (150 Ω each) on a single 5 V supply.
The input range of the ADA4859-3 includes ground, whereas
the output range is limited by the output headroom set by the
voltage drop across two diodes from each rail, which occurs
1.2 V from the positive and negative supply rails.
a
Figure 31. Discharging Cycle
The ADA4859-3 specifications make it especially suitable for SD
and HD video applications. It also allows dc-coupled video signal
with its black level set to 0 V and its sync tip down to −300 mV
for YPbPr video.
The charge pump is always on, even when the power-down pin
(PD) is enabled and the amplifier is off. However, it would be in
an idle state if the negative current were not used. Each amplifier
needs −6.3 mA of current, which totals −19 mA for all three
amplifiers. This means additional negative current may be available
by the charge pump for external use. Pin 4 (CPO) is the charge
pump output, which provides access to the negative supply
generated by the charge pump. Placing a 1 μF charge capacitor at
the CPO pin is essential to hold the charge and regulate the ripple.
If the negative supply is used to power another device in the
system, it is only possible for the 5 V supply operation. In the
3.3 V supply operation, the charge pump output current is very
limited. The capacitor at the CPO pin, which regulates the ripple
of the negative voltage, can be used as a coupling capacitor for the
external device. However, the charge pump current should be
limited to a maximum of 50 mA for external use. When powering
down the ADA4859-3, the charge pump is not affected and its
output voltage and current remain available for external use.
Rev. 0 | Page 12 of 16
ADA4859-3
APPLICATIONS INFORMATION
+VS
USING THE ADA4859-3 IN GAINS EQUAL TO +1, −1
10µF
The ADA4859-3 was designed to offer outstanding video
performance, simplify applications, and minimize board area.
0.1µF
RF
The ADA4859-3 is a triple amplifier with on-chip feedback
and gain set resistors. The gain is fixed internally at G = +2. The
inclusion of the on-chip resistors not only simplifies the design
of the application but also eliminates six surface-mount resistors,
saving valuable board space and lowering assembly costs.
Although the ADA4859-3 has a fixed gain of G = +2, it can be
used in other gain configurations, such as G = −1 and G = +1.
RG
VOUT
VIN
07715-131
RT
GAIN OF +1
Figure 33. Unity Gain of Option 2
Inverting Unity-Gain Operation
Unity-Gain Operation
Option 1
There are two options for obtaining unity gain (G = +1). The
first is shown in Figure 32. In this configuration, the −IN input
pin is tied to the output. (Feedback is provided through the two
internal 550 Ω resistors in parallel), and the input is applied to
the noninverting input. The noise gain for this configuration is 1.
+VS
In this configuration, the noninverting input is tied to ground
and the input signal is applied to the inverting input. The noise
gain for this configuration is +2, see Figure 34.
+VS
10µF
0.01µF
10µF
VIN
VOUT
RT
07715-132
0.1µF
GAIN OF –1
Figure 34. Inverting Configuration (G = −1)
VOUT
Figure 35 shows the small signal frequency response for both
gain of +1 (Option 1 and Option 2) and gain of −1 configurations.
It is clear that the G = +1 Option 2 has better flatness and no
peaking compared to Option 1.
07715-130
RT
GAIN OF +1
Figure 32. Unity Gain of Option 1
3
Another option exists for running the ADA4859-3 as a unitygain amplifier. In this configuration, the noise gain is +2, see
Figure 33. The frequency response and transient response for
this configuration closely match the gain of +2 plots because the
noise gains are equal. This method does have twice the noise
gain of Option 1; however, in applications that do not require low
noise, Option 2 offers less peaking and ringing. By tying the inputs
together, the net gain of the amplifier becomes +1. Equation 1
shows the transfer characteristic for the schematic shown in
Figure 33.
⎛ − RF
VOUT = V IN ⎜⎜
⎝ RG
⎞
⎛ R + RG
⎟ + V IN ⎜ F
⎟
⎜ R
G
⎠
⎝
⎞
⎟
⎟
⎠
CLOSED-LOOP GAIN (dB)
Option 2
G = +1,
OPTION 1
0
G = +1,
OPTION 2
–3
G = –1
–6
VS = 5V
VOUT = 2V p-p
RL = 100Ω
–9
(1)
1
10
100
FREQUENCY (MHz)
Figure 35. Large Signal, G = +1 and G = −1
which simplifies to VOUT = VIN.
Rev. 0 | Page 13 of 16
1000
07715-031
VIN
ADA4859-3
VIDEO LINE DRIVER
POWER-DOWN
The ADA4859-3 was designed to excel in video driver applications.
Figure 36 shows a typical schematic for a video driver operating
on bipolar supplies.
The ADA4859-3 is equipped with a PD (power-down) pin for
all three amplifiers. This allows the user the ability to reduce
the quiescent supply current when an amplifier is not active.
The power-down threshold levels are derived from ground
level. The amplifiers are powered down when the voltage
applied to the PD pin is greater than a certain voltage from
ground. In a 5 V supply application, the voltage is greater than 2 V,
and in a 3.3 V supply application, the voltage is greater than 1.5 V.
The amplifier is enabled whenever the PD pin is left floating
(not connected). If the PD pin is not used, it is best to leave it
floating or connected to ground. Note that the power-down feature
does not control the charge pump output voltage and current.
VIN (R)
75Ω
VOUT (R)
75Ω
16
15
14
13
12
1
2
1µF
VIN (G)
75Ω
11
CHARGE
PUMP
3
10 75Ω
9
4
VOUT (G)
Table 5. Power-Down Voltage Control
PD
1µF
10µF
+
5
0.1µF
6
7
8
75Ω
VIN (B)
VOUT (B)
07715-134
+VS
PD Pin
Not Active
Active
75Ω
In applications that require multiple video loads be driven
simultaneously, the ADA4859-3 can deliver. Figure 37 shows
the ADA4856-3 configured with two video loads, and Figure 38
shows the large signal performance for multiple video loads.
10µF
75Ω
75Ω
CABLE
VOUT1
75Ω
0.1µF
–
75Ω
75Ω
CABLE
75Ω
CABLE
VOUT2
75Ω
07715-135
+
VIN
75Ω
Figure 37. Video Driver Schematic for Two Video Loads
6.5
5.5
5.0
RL = 150Ω
4.5
RL = 75Ω
4.0
3.5
As is the case with all high speed applications, careful attention
to printed circuit board (PCB) layout details prevents associated
board parasitics from becoming problematic. Proper RF design
technique is mandatory. The PCB should have a ground plane
covering all unused portions of the component side of the board to
provide a low impedance return path. Removing the ground
plane on all layers from the area near the input and output pins
reduces stray capacitance. Locate termination resistors and loads as
close as possible to their respective inputs and outputs. Keep
input and output traces as far apart as possible to minimize
coupling (crosstalk) through the board. Adherence to
microstrip or stripline design techniques for long signal traces
(greater than about 1 inch) is recommended.
POWER SUPPLY BYPASSING
Careful attention must be paid to bypassing the power supply
pins of the ADA4859-3. Use high quality capacitors with low
equivalent series resistance (ESR), such as multilayer ceramic
capacitors (MLCCs), to minimize supply voltage ripple and
power dissipation. A large, usually tantalum, 10 μF to 47 μF
capacitor located in proximity to the ADA4859-3 is required to
provide good decoupling for lower frequency signals. In
addition, locate 0.1 μF MLCC decoupling capacitors as close to
each of the power supply pins as is physically possible, no more
than 1/8-inch away. The ground returns should terminate
immediately into the ground plane. Locating the bypass capacitor
return close to the load return minimizes ground loops and
improves performance.
3.0
2.5
1
10
100
1000
FREQUENCY (MHz)
07715-034
CLOSED-LOOP GAIN (dB)
6.0
3.3 V
<1 V
>1.5 V
LAYOUT CONSIDERATIONS
Figure 36. Video Driver Schematic
+VS
5V
<1.5 V
>2 V
Figure 38. Large Signal Frequency Response for Various Loads
Rev. 0 | Page 14 of 16
ADA4859-3
OUTLINE DIMENSIONS
4.00
BSC SQ
12° MAX
1.00
0.85
0.80
0.65 BSC
TOP
VIEW
3.75
BSC SQ
0.75
0.60
0.50
(BOTTOM VIEW)
9
0.80 MAX
0.65 TYP
SEATING
PLANE
PIN 1
INDICATOR
1
2.25
2.10 SQ
1.95
8
5
4
0.25 MIN
1.95 BSC
0.05 MAX
0.02 NOM
0.35
0.30
0.25
16
13
12
0.20 REF
COPLANARITY
0.08
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
072808-A
PIN 1
INDICATOR
0.60 MAX
0.60 MAX
COMPLIANT TO JEDEC STANDARDS MO-220-VGGC
Figure 39.16-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
4 mm × 4 mm Body, Very Thin Quad (CP-16-4)
Dimensions shown in millimeters
ORDERING GUIDE
Model
ADA4859-3ACPZ-R2 1
ADA4859-3ACPZ-R71
ADA4859-3ACPZ-RL1
1
Temperature Range
–40°C to +105°C
–40°C to +105°C
–40°C to +105°C
Package Description
16-Lead LFCSP_VQ
16-Lead LFCSP_VQ
16-Lead LFCSP_VQ
Z = RoHS Compliant Part.
Rev. 0 | Page 15 of 16
Package Option
CP-16-4
CP-16-4
CP-16-4
Ordering Quantity
250
1,500
5,000
ADA4859-3
NOTES
©2008 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D07715-0-11/08(0)
Rev. 0 | Page 16 of 16