a Balanced Modulator/Demodulator AD630 FEATURES Recovers Signal from 100 dB Noise 2 MHz Channel Bandwidth 45 V/s Slew Rate –120 dB Crosstalk @ 1 kHz Pin Programmable, Closed-Loop Gains of ⴞ1 and ⴞ2 0.05% Closed-Loop Gain Accuracy and Match 100 V Channel Offset Voltage (AD630BD) 350 kHz Full Power Bandwidth Chips Available PRODUCT DESCRIPTION The AD630 is a high precision balanced modulator that combines a flexible commutating architecture with the accuracy and temperature stability afforded by laser wafer trimmed thin film resistors. Its signal processing applications include balanced modulation and demodulation, synchronous detection, phase detection, quadrature detection, phase-sensitive detection, lock-in amplification, and square wave multiplication. A network of on-board applications resistors provides precision closed-loop gains of ± 1 and ± 2 with 0.05% accuracy (AD630B). These resistors may also be used to accurately configure multiplexer gains of +1, +2, +3, or +4. Alternatively, external feedback may be employed, allowing the designer to implement high gain or complex switched feedback topologies. FUNCTIONAL BLOCK DIAGRAM CM OFF ADJ CM OFF ADJ DIFF OFF ADJ 6 5 4 DIFF OFF ADJ 3 2.5k⍀ RINA 1 CH A+ AD630 AMP A 2 CH A– 20 A 12 COMP 11 +VS 13 VOUT 14 RB 15 RF 16 RA 2.5k⍀ RINB 17 AMP B B 10k⍀ CH B+ 18 10k⍀ –V CH B– 19 5k⍀ COMP 7 SEL B 9 CHANNEL STATUS B/A SEL A 10 8 –VS PRODUCT HIGHLIGHTS 1. The configuration of the AD630 makes it ideal for signal processing applications, such as balanced modulation and demodulation, lock-in amplification, phase detection, and square wave multiplication. The AD630 can be thought of as a precision op amp with two independent differential input stages and a precision comparator that is used to select the active front end. The rapid response time of this comparator coupled with the high slew rate and fast settling of the linear amplifiers minimize switching distortion. In addition, the AD630 has extremely low crosstalk between channels of –100 dB @ 10 kHz. 2. The application flexibility of the AD630 makes it the best choice for applications that require precisely fixed gain, switched gain, multiplexing, integrating-switching functions, and high speed precision amplification. The AD630 is used in precision signal processing and instrumentation applications that require wide dynamic range. When used as a synchronous demodulator in a lock-in amplifier configuration, it can recover a small signal from 100 dB of interfering noise (see Lock-In Amplifier Applications section). Although optimized for operation up to 1 kHz, the circuit is useful at frequencies up to several hundred kilohertz. 4. The op amp format of the AD630 ensures easy implementation of high gain or complex switched feedback functions. The application resistors facilitate the implementation of most common applications with no additional parts. Other features of the AD630 include pin programmable frequency compensation, optional input bias current compensation resistors, common-mode and differential-offset voltage adjustment, and a channel status output that indicates which of the two differential inputs is active. This device is now available to Standard Military Drawing (DESC) numbers 5962-8980701RA and 5962-89807012A. 3. The 100 dB dynamic range of the AD630 exceeds that of any hybrid or IC balanced modulator/demodulator and is comparable to that of costly signal processing instruments. 5. The AD630 can be used as a 2-channel multiplexer with gains of +1, +2, +3, or +4. The channel separation of 100 dB @ 10 kHz approaches the limit achievable with an empty IC package. 6. The AD630 has pin strappable frequency compensation (no external capacitor required) for stable operation at unity gain without sacrificing dynamic performance at higher gains. 7. Laser trimming of comparator and amplifying channel offsets eliminates the need for external nulling in most cases. REV. E Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 www.analog.com Fax: 781/326-8703 © 2004 Analog Devices, Inc. All rights reserved. Powered by TCPDF (www.tcpdf.org) IMPORTANT LINKS for the AD630* Last content update 05/03/2013 01:15 pm PARAMETRIC SELECTION TABLES DESIGN COLLABORATION COMMUNITY Find Similar Products By Operating Parameters Collaborate Online with the ADI support team and other designers about select ADI products. DOCUMENTATION AD630: Military Data Sheet AN-924: Digital Quadrature Modulator Gain AN-683: Strain Gage Measurement Using an AC Excitation AN-307: Modem-Circuit Techniques Simplify Instrumentation Designs AN-306: Synchronous System Measures micro-Ohms AN-214: Ground Rules for High Speed Circuits AN-349: Keys to Longer Life for CMOS AN-308: Commutating Amp Multiplies Precisely ADI Warns Against Misuse of COTS Integrated Circuits Space Qualified Parts List Leading Inside Advertorials: Broadband I/Q Modulator Eases Radio Design ADL5375 Modulator / ADL5382 Demodulator Follow us on Twitter: www.twitter.com/ADI_News Like us on Facebook: www.facebook.com/AnalogDevicesInc DESIGN SUPPORT Submit your support request here: Linear and Data Converters Embedded Processing and DSP Telephone our Customer Interaction Centers toll free: Americas: Europe: China: India: Russia: 1-800-262-5643 00800-266-822-82 4006-100-006 1800-419-0108 8-800-555-45-90 Quality and Reliability Lead(Pb)-Free Data EVALUATION KITS & SYMBOLS & FOOTPRINTS Symbols and Footprints SAMPLE & BUY AD630 View Price & Packaging Request Evaluation Board Request Samples Check Inventory & Purchase Find Local Distributors * This page was dynamically generated by Analog Devices, Inc. and inserted into this data sheet. Note: Dynamic changes to the content on this page (labeled 'Important Links') does not constitute a change to the revision number of the product data sheet. This content may be frequently modified. AD630–SPECIFICATIONS (@ 25ⴗC and ⴞV = ⴞ15 V, unless otherwise noted.) S Model GAIN Open-Loop Gain ± 1, ± 2 Closed-Loop Gain Error Closed-Loop Gain Match Closed-Loop Gain Drift CHANNEL INPUTS VIN Operational Limit1 Input Offset Voltage Input Offset Voltage TMIN to TMAX Input Bias Current Input Offset Current Channel Separation @ 10 kHz COMPARATOR VIN Operational Limit1 Switching Window Switching Window TMIN to TMAX Input Bias Current Response Time (–5 mV to +5 mV Step) Channel Status ISINK @ VOL = –VS + 0.4 V2 Pull-Up Voltage Min 90 110 0.1 0.1 2 100 10 100 AD630K/AD630B Typ Max 120 (–VS + 4 V) to (+VS – 1 V) 100 800 300 50 100 10 100 ± 2.0 300 100 200 OUTPUT VOLTAGE, @ RL = 2 kΩ TMIN to TMAX Output Short-Circuit Current ± 10 4 90 90 ±5 110 110 ± 16.5 5 ± 10 100 200 0 –25 ± 2.5 300 (–VS + 33 V) 90 90 ±5 V mV mV nA ns mA V 110 110 dB dB V mA ± 16.5 5 V mA 25 N/A –55 µV nA nA dB MHz V/µs µs ± 10 70 +85 V µV 2 45 3 4 25 70 +85 1000 300 50 1.6 4 25 0 –25 dB % % ppm/°C (–VS + 3 V) to (+VS – 1.3 V) ± 1.5 2 45 3 ± 16.5 5 110 0.1 0.1 2 (–VS + 33 V) 2 45 3 105 110 Unit 100 10 100 ± 2.0 300 1.6 AD630S Typ Max (–VS + 4 V) to (+VS – 1 V) 500 160 300 50 (–VS + 3 V) to (+VS – 1.5 V) ± 1.5 (–VS + 33 V) 85 90 ±5 90 2 1.6 OPERATING CHARACTERISTICS Common-Mode Rejection Power Supply Rejection Supply Voltage Range Supply Current Min 0.05 0.05 (–VS + 3 V) to (+VS – 1.5 V) ± 1.5 100 200 Min 100 (–VS + 4 V) to (+VS – 1 V) 500 DYNAMIC PERFORMANCE Unity Gain Bandwidth Slew Rate3 Settling Time to 0.1% (20 V Step) TEMPERATURE RANGES Rated Performance–N Package Rated Performance–D Package AD630J/AD630A Typ Max +125 °C °C NOTES 1 If one terminal of each differential channel or comparator input is kept within these limits the other terminal may be taken to the positive supply. 2 ISINK @ VOL = (–VS + 1); V is typically 4 mA. 3 Pin 12 Open. Slew rate with Pin 12 and Pin 13 shorted is typically 35 V/ µs. Specifications subject to change without notice. –2– REV. E AD630 ABSOLUTE MAXIMUM RATINGS Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 18 V Internal Power Dissipation . . . . . . . . . . . . . . . . . . . . 600 mW Output Short-Circuit to Ground . . . . . . . . . . . . . . . Indefinite Storage Temperature, Ceramic Package . . . –65°C to +150°C Storage Temperature, Plastic Package . . . . . –55°C to +125°C Lead Temperature Range (Soldering, 10 sec) . . . . . . . . 300°C Maximum Junction Temperature . . . . . . . . . . . . . . . . . 150°C THERMAL CHARACTERISTICS 20-Lead PDIP (N) 20-Lead Ceramic DIP (D) 20-Lead Leadless Chip Carrier LCC (E) 20-Lead SOIC (R-20) JC JA 24°C/W 35°C/W 35°C/W 38°C/W 61°C/W 120°C/W 120°C/W 75°C/W ORDERING GUIDE Model Temperature Ranges Package Description Package Option AD630JN AD630KN AD630AR AD630AR-REEL AD630AD AD630BD AD630SD AD630SD/883B 5962-8980701RA AD630SE/883B 5962-89807012A AD630JCHIPS AD630SCHIPS 0°C to 70°C 0°C to 70°C –25°C to +85°C –25°C to +85°C –25°C to +85°C –25°C to +85°C –55°C to +125°C –55°C to +125°C –55°C to +125°C –55°C to +125°C –55°C to +125°C 0°C to 70°C –55°C to +125°C PDIP PDIP SOIC SOIC 13" Tape and Reel SBDIP SBDIP SBDIP SBDIP SBDIP CLCC CLCC Chip Chip N-20 N-20 R-20 R-20 D-20 D-20 D-20 D-20 D-20 E-20A E-20A CHIP METALLIZATION AND PINOUT PIN CONFIGURATIONS Dimensions shown in inches and (millimeters). Contact factory for latest dimensions. 20-Lead SOIC, PDIP, and CERDIP RINA 1 20 CH A– CH A+ 2 19 CH B– DIFF OFF ADJ 3 18 CH B+ DIFF OFF ADJ 4 17 RINB AD630 CM OFF ADJ 5 16 RA TOP VIEW CM OFF ADJ 6 (Not to Scale) 15 RF 14 RB CHANNEL STATUS B/A 7 –VS 8 13 VOUT SEL B 9 12 COMP SEL A 10 11 +VS CH B– CH A+ 3 2 RIN A CH A– DIFF OFF ADJ 20-Terminal CLCC 1 20 19 CHIP AVAILABILITY The AD630 is available in laser trimmed, passivated chip form. The figure above shows the AD630 metallization pattern, bonding pads and dimensions. AD630 chips are available; consult factory for details. DIFF OFF ADJ 4 18 CH B+ CM OFF ADJ 5 AD630 CM OFF ADJ 6 TOP VIEW (Not to Scale) CHANNEL STATUS B/A 7 COMP VOUT SEL A +VS SEL B CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD630 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. –3– 16 RA 15 RF 14 RB –VS 8 9 10 11 12 13 REV. E 17 RINB AD630 AD630–Typical Performance Characteristics 15 15 18 15 10 Vi 5k⍀ 5k⍀ VO 5 2k⍀ 100pF CL = 100pF f = 1kHz 10 5k⍀ 5k⍀ Vi 5 VO RL 100pF CAP IN 0 1k 10k 0 1M 100k 1 10 FREQUENCY (Hz) TPC 1. Output Voltage vs. Frequency OUTPUT VOLTAGE (ⴞV) OUTPUT VOLTAGE (ⴞV) OUTPUT VOLTAGE (ⴞV) RL= 2k⍀ CL = 100pF 100 1k 10k 100k RESISTIVE LOAD (⍀) VO 100pF 10 5 f = 1kHz CL = 100pF 0 0 60 5k⍀ 2k⍀ 1M 5 10 15 SUPPLY VOLTAGE (ⴞV) TPC 3. Output Voltage Swing vs. Supply Voltage TPC 2. Output Voltage vs. Resistive Load 120 5k⍀ Vi 120 0 20 0 COMPENSATED dt 60 40 –20 20 –40 0 1 10 100 1k 10k FREQUENCY (Hz) 100k TPC 4. Common-Mode Rejection vs. Frequency 45 80 90 60 COMPENSATED 40 135 20 –60 –5 –4 –3 TPC 5. UNCOMPENSATED OPEN LOOP PHASE (ⴗC) 80 100 OPEN LOOP GAIN (dB) 40 (V/s) 100 dVO COMMON-MODE REJECTION (dB) UNCOMPENSATED 2 –2 –1 0 1 INPUT VOLTAGE (V) 3 4 dVO vs. Input Voltage dt –4– 5 0 0 10 100 1k 10k 100k FREQUENCY (Hz) 1M 180 10M TPC 6. Gain and Phase vs. Frequency REV. E AD630 20mV 10V ⴞ10V 20kHz (Vi) 100 90 20mV/DIV (Vo) 1mV 5s 100 90 1mV/DIV (B) 20mV/DIV (Vi) 10V/DIV (Vo) 10 0% 10 0% 500ns 20mV 10V TOP TRACE: Vo BOTTOM TRACE: Vi TOP TRACE: Vi MIDDLE TRACE: SETTLING ERROR (B) BOTTOM TRACE: Vo 15 16 5k⍀ 10k⍀ 2 20 CH A 13 19 18 10k⍀ Vi TOP TRACE VO 12 CH B 14 10k⍀ 15 20 2 CH A 12 VO BOTTOM TRACE 13 10k⍀ 10k⍀ 10k⍀ Vi 14 (B) MIDDLE TRACE HP5082-2811 9 10 TPC 9. Large Signal Inverting Step Response TPC 7. Channel-to-Channel Switch-Settling Characteristic 50mV 50mV/DIV (Vi) 1mV 100 90 1mV/DIV (A) 10 0% 100mV/DIV (Vo) 500ns 100mV TOP TRACE: Vi MIDDLE TRACE: SETTLING ERROR (A) BOTTOM TRACE: Vo 10k⍀ 14 10k⍀ 15 20 Vi TOP TRACE 2 CH A 12 1k⍀ VO BOTTOM TRACE 13 10k⍀ MIDDLE TRACE (A) 30pF 10k⍀ TEKTRONIX 7A13 TPC 8. Small Signal Noninverting Step Response REV. E –5– AD630 TWO WAYS TO LOOK AT THE AD630 The two closed-loop gain magnitudes will be equal when RF/RA = 1 + RF/RB, which will result from making RA equal to RFRB/ (RF + RB) the parallel equivalent resistance of RF and RB. The functional block diagram of the AD630 (see page 1) shows the pin connections of the internal functions. An alternative architectural diagram is shown in Figure 1. In this diagram, the individual A and B channel preamps, the switch, and the integrator output amplifier are combined in a single op amp. This amplifier has two differential input channels, only one of which is active at a time. The 5 kΩ and the two 10 kΩ resistors on the AD630 chip can be used to make a gain of 2 as shown below. By paralleling the 10 kΩ resistors to make RF equal to 5 kΩ and omitting RB, the circuit can be programmed for a gain of ± 1 (as shown in Figure 9a). These and other configurations using the on-chip resistors present the inverting inputs with a 2.5 kΩ source impedance. The more complete AD630 diagrams show 2.5 kΩ resistors available at the noninverting inputs which can be conveniently used to minimize errors resulting from input bias currents. +VS 11 15 14 16 RA 5k⍀ RB 10k⍀ 1 2 2.5k⍀ RF 10k⍀ A 20 RF 10k⍀ RA 5k⍀ 13 19 18 Vi B RB 10k⍀ 12 2.5k⍀ 17 7 SEL B VO = – B/A RF V RA i 9 SEL A 10 Figure 3. Inverting Gain Configuration 8 –VS Figure 1. Architectural Block Diagram Vi RA 5k⍀ HOW THE AD630 WORKS The basic mode of operation of the AD630 may be easier to recognize as two fixed gain stages which can be inserted into the signal path under the control of a sensitive voltage comparator. When the circuit is switched between inverting and noninverting gain, it provides the basic modulation/demodulation function. The AD630 is unique in that it includes laser wafer trimmed thin-film feedback resistors on the monolithic chip. The configuration shown in Figure 2 yields a gain of ± 2 and can be easily changed to ± 1 by shifting RB from its ground connection to the output. Vi 20 A 19 RB 10k⍀ 18 CIRCUIT DESCRIPTION The simplified schematic of the AD630 is shown in Figure 5. It has been subdivided into three major sections, the comparator, the two input stages, and the output integrator. The comparator consists of a front end made up of Q52 and Q53, a flip-flop load formed by Q3 and Q4, and two current steering switching cells Q28, Q29 and Q30, Q31. This structure is designed so that a differential input voltage greater than 1.5 mV in magnitude applied to the comparator inputs will completely select one of the switching cells. The sign of this input voltage determines which of the two switching cells is selected. RF 10k⍀ 13 ) Vi Figure 4. Noninverting Gain Configuration RA 5k⍀ 15 2 RF RB RF 10k⍀ RB 10k⍀ The comparator selects one of the two input stages to complete an operational feedback connection around the AD630. The deselected input is off and has a negligible effect on the operation. 16 VO = (1+ VO B CH A+ CH A– 2 20 14 +VS 9 CH B+ CH B– 19 18 11 Q33 Q35 Q34 Q36 i73 i55 10 Q44 SEL A Figure 2. AD630 Symmetric Gain (± 2) 10 When Channel B is selected, the resistors RA and RF are connected for inverting feedback as shown in the inverting gain configuration diagram in Figure 3. The amplifier has sufficient loop gain to minimize the loading effect of RB at the virtual ground produced by the feedback connection. When the sign of the comparator input is reversed, Input B will be deselected and A will be selected. The new equivalent circuit will be the noninverting gain configuration shown in Figure 4. In this case, RA will appear across the op amp input terminals, but since the amplifier drives this difference voltage to zero, the closed-loop gain is unaffected. Q52 Q53 Q62 Q65 Q67 Q70 13 9 SEL B C121 Q30 12 Q31 Q28 C122 Q29 Q24 Q3 –VS VOUT Q74 Q4 i22 COMP Q32 Q25 i23 8 3 4 5 6 DIFF OFF ADJ DIFF OFF ADJ CM OFF ADJ CM OFF ADJ Figure 5. AD630 Simplified Schematic –6– REV. E AD630 The collectors of each switching cell connect to an input transconductance stage. The selected cell conveys bias currents i22 and i23 to the input stage it controls, causing it to become active. The deselected cell blocks the bias to its input stage which, as a consequence, remains off. desired signal multiplied by the low frequency gain (which may be several hundred for large feedback ratios) with the switching signal and interference superimposed at unity gain. C The structure of the transconductance stages is such that it presents a high impedance at its input terminals and draws no bias current when deselected. The deselected input does not interfere with the operation of the selected input ensuring maximum channel separation. Another feature of the input structure is that it enhances the slew rate of the circuit. The current output of the active stage follows a quasi-hyperbolic-sine relationship to the differential input voltage. This means that the greater the input voltage, the harder this stage will drive the output integrator, and the faster the output signal will move. This feature helps ensure rapid, symmetric settling when switching between inverting and noninverting closed loop configurations. The output section of the AD630 includes a current mirrorload (Q24 and Q25), an integrator-voltage gain stage (Q32), and a complementary output buffer (Q44 and Q74). The outputs of both transconductance stages are connected in parallel to the current mirror. Since the deselected input stage produces no output current and presents a high impedance at its outputs, there is no conflict. The current mirror translates the differential output current from the active input transconductance amplifier into single-ended form for the output integrator. The complementary output driver then buffers the integrator output to produce a low impedance output. OTHER GAIN CONFIGURATIONS Many applications require switched gains other than the ± 1 and ± 2 which the self-contained applications resistors provide. The AD630 can be readily programmed with three external resistors over a wide range of positive and negative gain by selecting and RB and RF to give the noninverting gain 1 + RF/RB and subsequent RA to give the desired inverting gain. Note that when the inverting magnitude equals the noninverting magnitude, the value of RA is found to be RBRF/(RB + RF). That is, RA should equal the parallel combination of RB and RF to match positive and negative gain. The feedback synthesis of the AD630 may also include reactive impedance. The gain magnitudes will match at all frequencies if the A impedance is made to equal the parallel combination of the B and F impedances. The same considerations apply to the AD630 as to conventional op amp feedback circuits. Virtually any function that can be realized with simple noninverting “L network” feedback can be used with the AD630. A common arrangement is shown in Figure 6. The low frequency gain of this circuit is 10. The response will have a pole (–3 dB) at a frequency f ⯝ 1/(2 π 100 kΩC) and a zero (3 dB from the high frequency asymptote) at about 10 times this frequency. The 2 kΩ resistor in series with each capacitor mitigates the loading effect on circuitry driving this circuit, eliminates stability problems, and has a minor effect on the pole-zero locations. As a result of the reactive feedback, the high frequency components of the switched input signal will be transmitted at unity gain while the low frequency components will be amplified. This arrangement is useful in demodulators and lock-in amplifiers. It increases the circuit dynamic range when the modulation or interference is substantially larger than the desired signal amplitude. The output signal will contain the REV. E 2k⍀ C 2k⍀ 10k⍀ 100k⍀ Vi 2 20 A 13 VO 19 11.11k⍀ 18 B 12 7 SEL B SEL A CHANNEL STATUS B/A 9 10 8 –V S Figure 6. AD630 with External Feedback SWITCHED INPUT IMPEDANCE The noninverting mode of operation is a high input impedance configuration while the inverting mode is a low input impedance configuration. This means that the input impedance of the circuit undergoes an abrupt change as the gain is switched under control of the comparator. If gain is switched when the input signal is not zero, as it is in many practical cases, a transient will be delivered to the circuitry driving the AD630. In most applications, this will require the AD630 circuit to be driven by a low impedance source which remains “stiff ” at high frequencies. Generally, this will be a wideband buffer amplifier. FREQUENCY COMPENSATION The AD630 combines the convenience of internal frequency compensation with the flexibility of external compensation by means of an optional self-contained compensation capacitor. In gain of ± 2 applications, the noise gain that must be addressed for stability purposes is actually 4. In this circumstance, the phase margin of the loop will be on the order of 60° without the optional compensation. This condition provides the maximum bandwidth and slew rate for closed loop gains of |2| and above. When the AD630 is used as a multiplexer, or in other configurations where one or both inputs are connected for unity gain feedback, the phase margin will be reduced to less than 20°. This may be acceptable in applications where fast slewing is a first priority, but the transient response will not be optimum. For these applications, the self-contained compensation capacitor may be added by connecting Pin 12 to Pin 13. This connection reduces the closed-loop bandwidth somewhat and improves the phase margin. For intermediate conditions, such as gain of ± 1 where loop attenuation is 2, use of the compensation should be determined by whether bandwidth or settling response must be optimized. The optional compensation should also be used when the AD630 is driving capacitive loads or whenever conservative frequency compensation is desired. OFFSET VOLTAGE NULLING The offset voltages of both input stages and the comparator have been pretrimmed so that external trimming will only be required in the most demanding applications. The offset adjustment of the two input channels is accomplished by means of a differential and common-mode scheme. This facilitates fine adjustment of system errors in switched gain applications. With –7– AD630 AD630 when used to modulate a 100 kHz square wave carrier with a 10 kHz sinusoid. The result is the double sideband suppressed carrier waveform. the system input tied to 0 V, and a switching or carrier waveform applied to the comparator, a low level square wave will appear at the output. The differential offset adjustment potentiometers can be used to null the amplitude of this square wave (Pins 3 and 4). The common-mode offset adjustment can be used to zero the residual dc output voltage (Pins 5 and 6). These functions should be implemented using 10k trim potentiometers with wipers connected directly to Pin 8 as shown in Figures 9a and 9b. These balanced modulator topologies accept two inputs, a signal (or modulation) input applied to the amplifying channels and a reference (or carrier) input applied to the comparator. 10k⍀ CHANNEL STATUS OUTPUT 6 The channel status output, Pin 7, is an open collector output referenced to –VS that can be used to indicate which of the two input channels is active. The output will be active (pulled low) when Channel A is selected. This output can also be used to supply positive feedback around the comparator. This produces hysteresis which serves to increase noise immunity. Figure 7 shows an example of how hysteresis may be implemented. Note that the feedback signal is applied to the inverting (–) terminal of the comparator to achieve positive feedback. This is because the open collector channel status output inverts the output sense of the internal comparator. MODULATION INPUT DIFF ADJ 4 5 3 2.5k⍀ 1 AMP A 12 A 2 +VS 11 20 2.5k⍀ 17 13 B AMP B 10k⍀ 14 –V 18 19 10k⍀ AD630 CARRIER INPUT MODULATED OUTPUT SIGNAL 15 16 5k⍀ COMP 7 9 10 8 –VS Figure 9a. AD630 Configured as a Gain-of-One Balanced Modulator +5V 1M⍀ 10k⍀ CM ADJ 100k⍀ 100k⍀ 9 7 10k⍀ 10k⍀ CM ADJ 10 DIFF ADJ 8 –15V 100⍀ 6 MODULATION INPUT 4 5 3 2.5k⍀ 1 AMP A 12 A 2 +VS 11 Figure 7. Comparator Hysteresis 20 2.5k⍀ The channel status output may be interfaced with TTL inputs as shown in Figure 8. This circuit provides appropriate level shifting from the open-collector AD630 channel status output to TTL inputs. 17 B AMP B 10k⍀ 14 –V 18 19 CARRIER INPUT 13 10k⍀ AD630 COMP MODULATED OUTPUT SIGNAL 15 16 5k⍀ 7 9 10 8 +5V +15V –VS 22k⍀ 6.8k⍀ AD630 100k⍀ 7 Figure 9b. AD630 Configured as a Gain-of-Two Balanced Modulator IN 914s 2N2222 TTL INPUT 8 5V 5V 20s –15V MODULATION INPUT Figure 8. Channel Status—TTL Interface APPLICATIONS: BALANCED MODULATOR CARRIER INPUT Perhaps the most commonly used configuration of the AD630 is the balanced modulator. The application resistors provide precise symmetric gains of ± 1 and ± 2. The ± 1 arrangement is shown in Figure 9a and the ± 2 arrangement is shown in Figure 9b. These cases differ only in the connection of the 10 kΩ feedback resistor (Pin 14) and the compensation capacitor (Pin 12). Note the use of the 2.5 kΩ bias current compensation resistors in these examples. These resistors perform the identical function in the ± 1 gain case. Figure 10 demonstrates the performance of the OUTPUT SIGNAL 10V Figure 10. Gain-of-Two Balanced Modulator Sample Waveforms –8– REV. E AD630 BALANCED DEMODULATOR The balanced modulator topology described above will also act as a balanced demodulator if a double sideband suppressed carrier waveform is applied to the signal input and the carrier signal is applied to the reference input. The output under these circumstances will be the baseband modulation signal. Higher order carrier components that can be removed with a low-pass filter will also be present. Other names for this function are synchronous demodulation and phase-sensitive detection. 2.5kHZ 2V p-p SINUSOIDAL EXCITATION E1000 AD544 SCHAEVITZ AD630 FOLLOWER A LVDT ⴞ2 DEMODULATOR 16 B 5k⍀ 15 10k⍀ 1 2.5k⍀ A 20 C 13 100k⍀ 14 10k⍀ 19 B 12 17 1F 2.5k⍀ The balanced modulator topologies of Figures 9a and 9b can also be used as precision phase comparators. In this case, an ac waveform of a particular frequency is applied to the signal input and a waveform of the same frequency is applied to the reference input. The dc level of the output (obtained by low-pass filtering) will be proportional to the signal amplitude and phase difference between the input signals. If the signal amplitude is held constant, the output can be used as a direct indication of the phase. When these input signals are 90° out of phase, they are said to be in quadrature and the AD630 dc output will be zero. 10 Figure 11. LVDT Signal Conditioner AC BRIDGE Bridge circuits that use dc excitation are often plagued by errors caused by thermocouple effects, 1/f noise, dc drifts in the electronics, and line noise pick-up. One way to get around these problems is to excite the bridge with an ac waveform, amplify the bridge output with an ac amplifier, and synchronously demodulate the resulting signal. The ac phase and amplitude information from the bridge is recovered as a dc signal at the output of the synchronous demodulator. The low frequency system noise, dc drifts, and demodulator noise all get mixed to the carrier frequency and can be removed by means of a low-pass filter. Dynamic response of the bridge must be traded off against the amount of attenuation required to adequately suppress these residual carrier components in the selection of the filter. Figure 12 is an example of an ac bridge system with the AD630 used as a synchronous demodulator. The bridge is excited by a 1 V 400 Hz excitation. Trace A in Figure 13 is the amplified bridge signal. Trace B is the output of the synchronous demodulator and Trace C is the filtered dc system output. PRECISION RECTIFIER ABSOLUTE VALUE If the input signal is used as its own reference in the balanced modulator topologies, the AD630 will act as a precision rectifier. The high frequency performance will be superior to that which can be achieved with diode feedback and op amps. There are no diode drops that the op amp must “leap over” with the commutating amplifier. LVDT SIGNAL CONDITIONER Many transducers function by modulating an ac carrier. A linear variable differential transformer (LVDT) is a transducer of this type. The amplitude of the output signal corresponds to core displacement. Figure 11 shows an accurate synchronous demodulation system which can be used to produce a dc voltage that corresponds to the LVDT core position. The inherent precision and temperature stability of the AD630 reduce demodulator drift to a second-order effect. +15V 1V 400Hz 350⍀ +IN 350⍀ A 350⍀ AD8221 49.9⍀ REF 9 11 SEL B +VS 16 RA 17 RINB 19 CH B– –IN AD630AR B 20 CH A– 15 RF RINA SEL A –VS RB 1 10 8 –15V Figure 12. AC Bridge System –9– 4.99k⍀ 4.99k⍀ 4.99k⍀ 2F 2F 2F VOUT 13 COMP 12 REV. E 9 PHASE SHIFTER PRECISION PHASE COMPARATOR 350⍀ D 14 C AD630 [ T ] 5V 500s/DIV B. 200mV/DIV 5V 5s MODULATED SIGNAL (A) (UNATTENUATED) 100 90 ATTENUATED SIGNAL PLUS NOISE (B) T 3 10 OUTPUT 0% 5mV C. 200mV/DIV A. 200mV/DIV Figure 15. Lock-In Amplifier Waveforms Figure 13. AC Bridge Waveforms (1 V Excitation) LOCK-IN AMPLIFIER APPLICATIONS Lock-in amplification is a technique used to separate a small, narrow-band signal from interfering noise. The lock-in amplifier acts as a detector and narrow-band filter combined. Very small signals can be detected in the presence of large amounts of uncorrelated noise when the frequency and phase of the desired signal are known. The lock-in amplifier is basically a synchronous demodulator followed by a low-pass filter. An important measure of performance in a lock-in amplifier is the dynamic range of its demodulator. The schematic diagram of a demonstration circuit which exhibits the dynamic range of an AD630 as it might be used in a lock-in amplifier is shown in Figure 14. Figure 15 is an oscilloscope photo demonstrating the large dynamic range of the AD630. The photo shows the recovery of a signal modulated at 400 Hz from a noise signal approximately 100,000 times larger. CLIPPED BAND-LIMITED WHITE NOISE C B 16 AD542 5k⍀ 15 20 19 100R 10k⍀ 1 2.5k⍀ 17 2.5k⍀ 100dB ATTENUATION AD630 A AD542 13 The test signal is produced by modulating a 400 Hz carrier with a 0.1 Hz sine wave. The signals produced, for example, by chopped radiation (i.e., IR, optical) detectors may have similar low frequency components. A sinusoidal modulation is used for clarity of illustration. This signal is produced by a circuit similar to Figure 9b and is shown in the upper trace of Figure 15. It is attenuated 100,000 times normalized to the output, B, of the summing amplifier. A noise signal that might represent, for example, background and detector noise in the chopped radiation case, is added to the modulated signal by the summing amplifier. This signal is simply band limited clipped white noise. Figure 15 shows the sum of attenuated signal plus noise in the center trace. This combined signal is demodulated synchronously using phase information derived from the modulator, and the result is low-pass filtered using a 2-pole simple filter which also provides a gain of 100 to the output. This recovered signal is the lower trace of Figure 15. The combined modulated signal and interfering noise used for this illustration is similar to the signals often requiring a lock-in amplifier for detection. The precision input performance of the AD630 provides more than 100 dB of signal range and its dynamic response permits it to be used with carrier frequencies more than two orders of magnitude higher than in this example. A more sophisticated low-pass output filter will aid in rejecting wider bandwidth interference. R B 100R 14 10k⍀ C OUTPUT A 10 0.1Hz 9 MODULATED CARRIER 400Hz PHASE CARRIER REFERENCE LOW-PASS FILTER Figure 14. Lock-In Amplifier –10– REV. E AD630 OUTLINE DIMENSIONS 20-Lead Side-Brazed Ceramic Dual In-Line Package [SBDIP] (D-20) Dimensions shown in inches and (millimeters) 0.080 (2.03) MAX 0.005 (0.13) MIN PIN 1 20 11 1 10 0.300 (7.62) 0.280 (7.11) 1.060 (28.92) 0.990 (25.15) 0.200 (5.08) MAX 0.200 (5.08) 0.125 (3.18) 0.023 (0.58) 0.014 (0.36) 0.100 (2.54) BSC 0.320 (8.13) 0.300 (7.62) 0.060 (1.52) 0.015 (0.38) 0.150 (3.81) MIN 0.070 (1.78) SEATING PLANE 0.030 (0.76) 0.015 (0.38) 0.008 (0.20) CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN 20-Lead Plastic Dual In-Line Package [PDIP] (N-20) Dimensions shown in inches and (millimeters) 0.985 (25.02) 0.965 (24.51) 0.945 (24.00) 20 11 1 10 0.180 (4.57) MAX 0.150 (3.81) 0.130 (3.30) 0.110 (2.79) 0.295 (7.49) 0.285 (7.24) 0.275 (6.99) 0.325 (8.26) 0.310 (7.87) 0.300 (7.62) 0.015 (0.38) MIN 0.022 (0.56) 0.018 (0.46) 0.014 (0.36) 0.150 (3.81) 0.135 (3.43) 0.120 (3.05) 0.015 (0.38) 0.010 (0.25) 0.008 (0.20) 0.100 0.060 (1.52) SEATING (2.54) 0.050 (1.27) PLANE BSC 0.045 (1.14) COMPLIANT TO JEDEC STANDARDS MO-095-AE CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN 20-Terminal Ceramic Leadless Chip Carrier [LCC] (E-20A) Dimensions shown in inches and (millimeters) 0.100 (2.54) 0.064 (1.63) 0.200 (5.08) REF 0.100 (2.54) REF 0.015 (0.38) MIN 0.075 (1.91) REF 0.095 (2.41) 0.075 (1.90) 3 4 19 18 20 0.358 (9.09) 0.342 (8.69) SQ 0.358 (9.09) MAX SQ 0.088 (2.24) 0.054 (1.37) 0.011 (0.28) 0.007 (0.18) R TYP 0.075 (1.91) REF 0.055 (1.40) 0.045 (1.14) 1 BOTTOM VIEW 14 13 0.028 (0.71) 0.022 (0.56) 0.050 (1.27) BSC 8 9 45 TYP 0.150 (3.81) BSC CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETERS DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN REV. E –11– AD630 20-Lead Standard Small Outline Package [SOIC] Wide Body (R-20) Dimensions shown in millimeters and (inches) 20 C00784–0–6/04(E) 13.00 (0.5118) 12.60 (0.4961) 11 7.60 (0.2992) 7.40 (0.2913) 1 2.65 (0.1043) 2.35 (0.0925) 0.30 (0.0118) 0.10 (0.0039) COPLANARITY 0.10 10.65 (0.4193) 10.00 (0.3937) 10 1.27 (0.0500) BSC 8ⴗ 0.51 (0.0201) SEATING 0.33 (0.0130) 0ⴗ 0.31 (0.0122) PLANE 0.20 (0.0079) 0.75 (0.0295) ⴛ 45ⴗ 0.25 (0.0098) 1.27 (0.0500) 0.40 (0.0157) COMPLIANT TO JEDEC STANDARDS MS-013AC CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN Revision History Location Page 6/04—Data Sheet changed from REV. D to REV. E. Changes to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Replaced Figure 12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Changes to AC BRIDGE section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Replaced Figure 13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Changes to LOCK-IN AMPLIFIER APPLICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Updated OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 6/01—Data Sheet changed from REV. C to REV. D. Changes to SPECIFICATION TABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Changes to THERMAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Changes to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Changes to PIN CONFIGURATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Changes to OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 –12– REV. E