CGS74CT2524 CGS74CT2524 1 to 4 Minimum Skew (300 ps) Clock Driver Literature Number: SNOS683A CGS74CT2524 1 to 4 Minimum Skew (300 ps) Clock Driver General Description Features These minimum skew clock drivers are designed for Clock Generation and Support (CGS) applications operating at high frequencies. This device guarantees minimum output skew across the outputs of a given device. Skew parameters are also provided as a means to measure duty cycle requirements as those found in high speed clocking systems. The CGS74CT2524 is a minimum skew clock driver with one input driving four outputs, specifically designed for signal generation and clock distribution applications. Y Logic Symbol Connection Diagrams Y Y Y Y Y et Y Guaranteed 300 ps pin-to-pin skew (tOSHL and tOSLH) Implemented on National’s FACTTM family process 1 input to 4 outputs low skew clock distribution Symmetric output current drive: 24 mA IOH/IOL Industrial temperature of b40§ C to a 85§ C 8-pin SOIC package Low dynamic power consumption above 20 MHz Guaranteed 2 kV ESD protection e Y bs ol Pin Assignment SOIC (M) TL/F/11752– 1 TL/F/11752 – 2 The output pins act as a single entity and will follow the state of the CLK when the clock distribution chip is selected. Pin Description Pin Names Descripton CLK O0 – O3 Clock Input Outputs O Truth Table Inputs Outputs CLK O0 – O3 L H L H TL/F/11752 – 3 L e Low Logic Level H e High Logic Level FACTTM is a trademark of National Semiconductor Corporation. C1995 National Semiconductor Corporation TL/F/11752 RRD-B30M115/Printed in U. S. A. CGS74CT2524 1 to 4 Minimum Skew (300 ps) Clock Driver September 1995 Absolute Maximum Ratings (Note) Recommended Operating Conditions If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/Distributors for availability and specifications. e Supply Voltage (VCC) 4.5V to 5.5V 0V to VCC Input Voltage (VI) Output Voltage (VO) 0 to VCC b 40§ C to a 85§ C Operating Temperature (TA) Input Rise and Fall Times (0.8V to 2.0V) 9.6 ns max NOTE: The Absolute Maximum Ratings are those values beyond which the safety of the device cannot be guaranteed. The device should not be operated at these limits. The parametric values defined in the DC and AC Electrical Characteristics tables are not guaranteed at the absolute maximum ratings. The Recommended Operating Conditions will define the conditions for actual device operation. b 0.5 to 7.0V Supply Voltage (VCC) DC Input Voltage Diode Current (IIK) b 20 mA V e b0.5V a 20 mA V e VCC a 0.5V b 0.5V to (VCC a 0.5V) DC Input Voltage (VI) DC Output Diode (Current) (IO) b 20 mA V e b0.5V a 20 mA V e VCC a 0.5V b 0.5V to (VCC a 0.5V) DC Output Voltage (VO) DC Output Source g 50 mA or Sink Current (IO) DC VCC or Ground Current g 50 mA per Output Pin (ICC or IGND) b 65§ C to a 150§ C Storage Temperature (TSTG) Junction Temperature (iJA) 0 225 500 LFM M 167 132 117§ C/W N 115 79 62 § C/W DC Electrical Characteristics et Over recommended operating conditions unless specified otherwise. CGS74CT2524 Symbol Parameter VCC (V) TA e a 25§ C Typ Units Conditions 2.0 2.0 V VOUT e 0.1V or VCC e b0.1V TA e b40§ C to a 85§ C Guaranteed Limits Minimum High Level Input Voltage 4.5 5.5 1.5 1.5 2.0 2.0 VIL Maximum Low Level Input Voltage 4.5 5.5 1.5 1.5 0.8 0.8 0.8 0.8 V VOUT e 0.1V or VCC e b0.1V VOH Minimum High Level Output Voltage 4.5 5.5 4.49 5.49 4.4 5.4 4.4 5.4 V VIN e VIH IOUT e b50 mA 3.86 4.86 3.76 4.76 V VIN e VIH IOH e b24 mA 0.1 0.1 0.1 0.1 V VIN e VIL IOUT e 50 mA 4.5 5.5 0.36 0.36 0.44 0.44 V VIN e VIL IOL e 24 mA g 0.1 g 1.0 mA VI e VCC, GND VI e VCC b 2.1V bs ol VIH 4.5 5.5 VOL Minimum Low Level Output Voltage 4.5 5.5 0.001 0.001 Maximum Input Leakage Current 5.5 ICCT Maximum ICC/Input 5.5 1.5 mA IOLD Minimum Dynamic Output Current 5.5 75 mA VOLD e 1.65V Max 5.5 b 75 mA VOHD e 3.85V Min 80 mA VIN e VCC or GND O IIN IOHD ICC Maximum Quiescent Supply Current 5.5 0.6 8.0 2 AC Electrical Characteristics Over recommended operating conditions unless specified otherwise. All typical values are measured at VCC e 5V, TA e 25§ C. CGS74CT2524 Symbol VCC e 4.5V to 5.5V TA e b40§ C to a 85§ C CL e 50 pF RL e 500X Parameter Min Typ Units Max tPLH Low-to-High Propagation Delay CLK to On 3.5 9.0 ns tPHL High-to-Low Propagation Delay CLK to On 3.5 9.0 ns Extended AC Electrical Characteristics Over recommended operating conditions unless specified otherwise. All typical values are measured at VCC e 5V, TA e 25§ C. Parameter Package Fmax Maximum Operating Frequency tOSHL Maximum Skew Common Edge Output-to-Output Variation (Note 1) tPS trise tfall THigh TLow Min Typ Max 100 MHz M M (Note 2) N 300 450 500 ps M M (Note 2) N 300 450 500 ps Maximum Skew Pin (Signal) Transition Variation (Note 3) 1.0 ns Rise Time/Fall Time (from 0.8V to 2.0V/2.0V to 0.8V) 1.5 ns Maximum Skew Common Edge Output-to-Output Variation (Note 1) bs ol tOSLH Units et Symbol e CGS74CT2524 VCC e 4.5V to 5.5V TA e b40§ C to a 85§ C CL e 50 pF RL e 500X Time High 4 ns Time Low 4 ns Note 1: Output-to-Output Skew is defined as the absolute value of the difference between the actual propagation delay from any outputs within the same packaged device. The specifications apply to any outputs switching in the same direction either HIGH to LOW (tOSHL) or LOW to HIGH (tOSLH) or in opposite directions both HL and LH (tOST). tOSHL and tOSLH are characterized and guaranteed by design @ 1 MHz. Note 2: Characterized at 66 MHz. Parameter guaranteed by design. Note 3: Pin transition skew is the absolute difference between High-to-Low and Low-to-High propagation delay measure at a given output pin. O Note 4: Load capacitance includes the test jig. 3 Timing Diagrams 1 to 4 Min-Skew Clock Driver et e TL/F/11752 – 4 bs ol TL/F/11752 – 5 TL/F/11752 – 13 Time high is measured with outputs above 2V. Time low is measured with outputs below 0.8V. Test Circuit RL is 500X CL is 50 pF for all prop delays and skew measurements. O TL/F/11752 – 6 4 Ordering Information Contact NSC Marketing for specific data of availability O bs ol et e TL/F/11752 – 14 5 e et 8 Lead (0.150× Wide) Molded Small Outline Package (M) NS Package Number M08A bs ol CGS74CT2524 1 to 4 Minimum Skew (300 ps) Clock Driver Physical Dimensions inches (millimeters) LIFE SUPPORT POLICY O NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation 1111 West Bardin Road Arlington, TX 76017 Tel: 1(800) 272-9959 Fax: 1(800) 737-7018 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Europe Fax: (a49) 0-180-530 85 86 Email: cnjwge @ tevm2.nsc.com Deutsch Tel: (a49) 0-180-530 85 85 English Tel: (a49) 0-180-532 78 32 Fran3ais Tel: (a49) 0-180-532 93 58 Italiano Tel: (a49) 0-180-534 16 80 National Semiconductor Hong Kong Ltd. 13th Floor, Straight Block, Ocean Centre, 5 Canton Rd. Tsimshatsui, Kowloon Hong Kong Tel: (852) 2737-1600 Fax: (852) 2736-9960 National Semiconductor Japan Ltd. Tel: 81-043-299-2309 Fax: 81-043-299-2408 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2011, Texas Instruments Incorporated