AD AD8236ARMZ-R71

40 μA Micropower Instrumentation
Amplifier with Zero Crossover Distortion
AD8236
FEATURES
CONNECTION DIAGRAM
Low power: 40 μA supply current (maximum)
Low input currents
1 pA input bias current
0.5 pA input offset current
High CMRR: 110 dB CMRR, G = 100
Space-saving MSOP
Zero input crossover distortion
Rail-to-rail input and output
Gain set with single resistor
Operates from 1.8 V to 5.5 V
–IN 1
8
+VS
RG 2
7
VOUT
RG 3
6
REF
+IN 4
5
–VS
08000-001
AD8236
TOP VIEW
(Not to Scale)
Figure 1.
APPLICATIONS
Medical instrumentation
Low-side current sense
Portable devices
4.5
G=5
VS = 5V
VREF = 2.5V
4.0
3.5
3.0
2.5
2.0
1.5
G=5
VS = 1.8V
VREF = 0.9V
1.0
08000-002
INPUT COMMON-MODE VOLTAGE (V)
5.0
0.5
0
–0.5
0
0.5
1.0
1.5 2.0 2.5 3.0 3.5
OUTPUT VOLTAGE (V)
4.0
4.5
5.0
5.5
Figure 2. Wide Common-Mode Voltage Range vs. Output Voltage
GENERAL DESCRIPTION
The AD8236 is the lowest power instrumentation amplifier
in the industry. It has rail-to-rail outputs and can operate on
voltages as low as 1.8 V. Its 40 μA maximum supply current
makes it an excellent choice in battery-powered applications.
The AD8236’s high input impedance, low input bias current of
1 pA, high CMRR of 110 dB (G = 100), small size, and low power
offer tremendous value. It has a wider common-mode voltage
range than typical three-op-amp instrumentation amplifiers,
making this a great solution for applications that operate on a
single 1.8 V or 3 V supply. An innovative input stage allows for
a wide rail-to-rail input voltage range without the crossover
distortion common in other designs.
Table 1. Instrumentation Amplifiers by Category 1
General
Purpose
AD8220
AD8221
AD8222
AD8228
AD8295
1
Zero Drift
AD8230
AD8231
AD8290
AD8293G80
AD8293G160
AD8553
AD8556
AD8557
Military
Grade
AD620
AD621
AD624
AD524
AD526
Low
Power
AD8236
AD627
AD623
AD8223
AD8226
High Speed
PGA
AD8250
AD8251
AD8253
See www.analog.com/inamps for the latest instrumentation amplifiers.
The AD8236 is available in an 8-lead MSOP and is specified
over the industrial temperature range of −40°C to +125°C.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2009 Analog Devices, Inc. All rights reserved.
AD8236
TABLE OF CONTENTS
Features .............................................................................................. 1 Layout .......................................................................................... 15 Applications ....................................................................................... 1 Reference Terminal .................................................................... 15 Connection Diagram ....................................................................... 1 Power Supply Regulation and Bypassing ................................ 15 General Description ......................................................................... 1 Input Bias Current Return Path ............................................... 16 Revision History ............................................................................... 2 Input Protection ......................................................................... 16 Specifications..................................................................................... 3 RF Interference ........................................................................... 16 Absolute Maximum Ratings............................................................ 7 Common-Mode Input Voltage Range ..................................... 17 Maximum Power Dissipation ..................................................... 7 Applications Information .............................................................. 18 ESD Caution .................................................................................. 7 AC-Coupled Instrumentation Amplifier ................................ 18 Pin Configuration and Function Descriptions ............................. 8 Low Power Heart Rate Monitor ............................................... 19 Typical Performance Characteristics ............................................. 9 Outline Dimensions ....................................................................... 20 Theory of Operation ...................................................................... 14 Ordering Guide .......................................................................... 20 Basic Operation .......................................................................... 14 Gain Selection ............................................................................. 14 REVISION HISTORY
5/09—Revision 0: Initial Version
Rev. 0 | Page 2 of 20
AD8236
SPECIFICATIONS
+VS = 5 V, −VS = 0 V (GND), VREF = 2.5 V, TA = 25°C, G = 5, RL = 100 kΩ to GND, unless otherwise noted.
Table 2.
Parameter
COMMON-MODE REJECTION RATIO (CMRR)
CMRR DC
G=5
G = 10
G = 100
G = 200
NOISE
Voltage Noise Spectral Density, RTI
RTI, 0.1 Hz to 10 Hz
G=5
G = 200
Current Noise
VOLTAGE OFFSET
Input Offset, VOS
Average Temperature Coefficient (TC)
Offset RTI vs. Supply (PSR)
G=5
G = 10
G = 100
G = 200
INPUT CURRENT
Input Bias Current
Overtemperature
Input Offset Current
Overtemperature
DYNAMIC RESPONSE
Small Signal Bandwidth, –3 dB
G=5
G = 10
G = 100
G = 200
Settling Time 0.01%
G=5
G = 10
G = 100
G = 200
Slew Rate
G = 5 to 100
Test Conditions
VS = ±2.5 V, VREF = 0 V
VCM = −1.8 V to +1.8 V
Min
Typ
86
90
100
100
94
100
110
110
dB
dB
dB
dB
76
nV/√Hz
4
4
15
μV p-p
μV p-p
fA/√Hz
f = 1 kHz, G = 5
Max
3.5
−40°C to +125°C
VS = 1.8 V to 5 V
100
110
110
110
Unit
2.5
mV
μV/°C
120
126
130
130
dB
dB
dB
dB
1
−40°C to +85°C
−40°C to +125°C
0.5
−40°C to +85°C
−40°C to +125°C
10
100
600
5
50
130
pA
pA
pA
pA
pA
pA
23
9
0.8
0.4
kHz
kHz
kHz
kHz
444
456
992
1816
μs
μs
μs
μs
9
mV/μs
VOUT = 4 V step
Rev. 0 | Page 3 of 20
AD8236
Parameter
GAIN
Gain Range
Gain Error
G=5
G = 10
G = 100
G = 200
Nonlinearity
G=5
G = 10
G = 100
G = 200
Gain vs. Temperature
G=5
G > 10
INPUT
Differential Impedance
Common-Mode Impedance
Input Voltage Range
OUTPUT
Output Voltage High, VOH
Output Voltage Low, VOL
Short-Circuit Limit, ISC
REFERENCE INPUT
RIN
IIN
Voltage Range
Gain to Output
POWER SUPPLY
Operating Range
Quiescent Current
Overtemperature
TEMPERATURE RANGE
For Specified Performance
1
Test Conditions
Min
G = 5 + 420 kΩ/RG
VS = ±2.5 V, VREF = 0 V, VOUT = −2 V to +2 V
5
Typ
Max
Unit
200 1
V/V
0.005
0.03
0.06
0.15
0.05
0.2
0.2
0.3
%
%
%
%
2
1.2
0.5
0.5
10
10
10
10
ppm
ppm
ppm
ppm
0.25
1
−50
ppm/°C
ppm/°C
+VS
GΩ||pF
GΩ||pF
V
RL = 10 kΩ or 100 kΩ
−40°C to +125°C
440||1.6
110||6.2
−40°C to +125°C
0
RL = 100 kΩ
−40°C to +125°C
RL = 10 kΩ
−40°C to +125°C
RL = 100 kΩ
−40°C to +125°C
RL = 10 kΩ
−40°C to +125°C
4.98
4.98
4.9
4.9
4.99
4.95
2
10
5
5
25
30
±55
−IN, +IN = 0 V
210
20
−VS
+VS
1
1.8
30
−40°C to +125°C
−40
Although the specifications of the AD8236 list only low to midrange gains, gains can be set beyond 200.
Rev. 0 | Page 4 of 20
V
V
V
V
mV
mV
mV
mV
mA
kΩ
nA
V
V/V
5.5
40
50
V
μA
μA
+125
°C
AD8236
+VS = 1.8 V, −VS = 0 V (GND), VREF = 0.9 V, TA = 25°C, G = 5, RL = 100 kΩ to GND, unless otherwise noted.
Table 3.
Parameter
COMMON-MODE REJECTION RATIO (CMRR)
CMRR DC
G=5
G = 10
G = 100
G = 200
NOISE
Voltage Noise Spectral Density, RTI
RTI, 0.1 Hz to 10 Hz
G=5
G = 200
Current Noise
VOLTAGE OFFSET
Input Offset, VOS
Average Temperature Coefficient (TC)
Offset RTI vs. Supply (PSR)
G=5
G = 10
G = 100
G = 200
INPUT CURRENT
Input Bias Current
Overtemperature
Input Offset Current
Overtemperature
DYNAMIC RESPONSE
Small Signal Bandwidth, –3 dB
G=5
G = 10
G = 100
G = 200
Settling Time 0.01%
G=5
G = 10
G = 100
G = 200
Slew Rate
G = 5 to 100
GAIN
Gain Range
Gain Error
G=5
G = 10
G = 100
G = 200
Test Conditions
VS = ±0.9 V, VREF = 0 V
VCM = −0.6 V to +0.6 V
Min
Typ
86
90
100
100
94
100
110
110
dB
dB
dB
dB
76
nV/√Hz
4
4
15
μV p-p
μV p-p
fA/√Hz
f = 1 kHz, G = 5
Max
3.5
−40°C to +125°C
VS = 1.8 V to 5 V
100
110
110
110
Unit
2.5
mV
μV/°C
120
126
130
130
dB
dB
dB
dB
1
−40°C to +85°C
−40°C to +125°C
0.5
−40°C to +85°C
−40°C to +125°C
10
100
600
5
50
130
pA
pA
pA
pA
pA
pA
23
9
0.8
0.4
kHz
kHz
kHz
kHz
143
178
1000
1864
μs
μs
μs
μs
11
mV/μs
VOUT = 1.4 V step
G = 5 + 420 kΩ/RG
VS = ±0.9 V, VREF = 0 V, VOUT = −0.6 V to +0.6 V
5
0.005
0.03
0.06
0.15
Rev. 0 | Page 5 of 20
200 1
V/V
0.05
0.2
0.2
0.3
%
%
%
%
AD8236
Parameter
Nonlinearity
G=5
G = 10
G = 100
G = 200
Gain vs. Temperature
G=5
G > 10
INPUT
Differential Impedance
Common-Mode Impedance
Input Voltage Range
OUTPUT
Output Voltage High, VOH
Output Voltage Low, VOL
Short-Circuit Limit, ISC
REFERENCE INPUT
RIN
IIN
Voltage Range
Gain to Output
POWER SUPPLY
Operating Range
Quiescent Current
Overtemperature
TEMPERATURE RANGE
For Specified Performance
1
Test Conditions
RL = 10 kΩ or 100 kΩ
Min
Typ
Max
Unit
1
1
0.5
0.4
10
10
10
10
ppm
ppm
ppm
ppm
0.25
1
−50
ppm/°C
ppm/°C
+VS
GΩ||pF
GΩ||pF
V
−40°C to +125°C
440||1.6
110||6.2
−40°C to +125°C
0
RL = 100 kΩ
−40°C to +125°C
RL = 10 kΩ
−40°C to +125°C
RL = 100 kΩ
−40°C to +125°C
RL = 10 kΩ
−40°C to +125°C
1.78
1.78
1.65
1.65
1.79
1.75
2
12
5
5
25
25
±6
−IN, +IN = 0 V
210
20
−VS
+VS
1
1.8
33
−40°C to +125°C
−40
Although the specifications of the AD8236 list only low to midrange gains, gains can be set beyond 200.
Rev. 0 | Page 6 of 20
V
V
V
V
mV
mV
mV
mV
mA
kΩ
nA
V
V/V
5.5
40
50
V
μA
μA
+125
°C
AD8236
ABSOLUTE MAXIMUM RATINGS
Table 4.
Rating
6V
See Figure 3
55 mA
±VS
±VS
−65°C to +125°C
−40°C to +125°C
300°C
140°C
The difference between the total drive power and the load power is
the drive power dissipated in the package.
PD = Quiescent Power + (Total Drive Power – Load Power)
⎛V V
PD = (VS × I S ) + ⎜⎜ S × OUT
RL
⎝ 2
⎞ VOUT 2
⎟–
⎟
RL
⎠
RMS output voltages should be considered. If RL is referenced to
−VS, as in single-supply operation, the total drive power is VS ×
IOUT. If the rms signal levels are indeterminate, consider the worst
case, when VOUT = VS/4 for RL to midsupply
PD = (VS × I S ) +
135°C/W
(VS / 4 )2
RL
140°C
In single-supply operation with RL referenced to −VS, worst case
is VOUT = VS/2.
2 kV
1 kV
200 V
Airflow increases heat dissipation, effectively reducing θJA. In
addition, more metal directly in contact with the package leads
from metal traces, through holes, ground, and power planes
reduces the θJA.
MAXIMUM POWER DISSIPATION
The maximum safe power dissipation in the package of the
AD8236 is limited by the associated rise in junction temperature
(TJ) on the die. The plastic encapsulating the die locally reaches
the junction temperature. At approximately 140°C, which is the
glass transition temperature, the plastic changes its properties.
Even temporarily exceeding this temperature limit may change
the stresses that the package exerts on the die, permanently
shifting the parametric performance of the AD8236.
The still-air thermal properties of the package and PCB (θJA),
the ambient temperature (TA), and the total power dissipated in
the package (PD) determine the junction temperature of the die.
The junction temperature is calculated as
TJ = TA + (PD × θJA)
Figure 3 shows the maximum safe power dissipation in the package
vs. the ambient temperature for the 8-lead MSOP on a 4-layer
JEDEC standard board. θJA values are approximations.
2.00
1.75
1.50
1.25
1.00
0.75
0.50
0.25
0
–40
–20
0
20
40
60
80
100
120
AMBIENT TEMPERATURE (°C)
Figure 3. Maximum Power Dissipation vs. Ambient Temperature
ESD CAUTION
The power dissipated in the package (PD) is the sum of the
quiescent power dissipation and the power dissipated in the
package due to the load drive for all outputs. The quiescent
power is the voltage between the supply pins (VS) times the
quiescent current (IS). Assuming the load (RL) is referenced to
midsupply, the total drive power is VS/2 × IOUT, some of which
is dissipated in the package and some in the load (VOUT × IOUT).
Rev. 0 | Page 7 of 20
08000-045
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
MAXIMUM POWER DISSIPATION (W)
Parameter
Supply Voltage
Power Dissipation
Output Short-Circuit Current
Input Voltage (Common Mode)
Differential Input Voltage
Storage Temperature Range
Operating Temperature Range
Lead Temperature (Soldering, 10 sec)
Junction Temperature
θJA (4-Layer JEDEC Standard Board)
8-Lead MSOP
Package Glass Transition Temperature
8-Lead MSOP
ESD
Human Body Model
Charge Device Model
Machine Model
AD8236
–IN 1
RG 2
RG 3
+IN 4
8
AD8236
+VS
7
TOP VIEW
(Not to Scale)
VOUT
6
REF
5
–VS
08000-004
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Figure 4. Pin Configuration
Table 5. Pin Function Descriptions
Pin No.
1
2, 3
4
5
6
7
8
Mnemonic
−IN
RG
+IN
−VS
REF
VOUT
+VS
Description
Negative Input Terminal (True Differential Input)
Gain Setting Terminals (Place Resistor Across the RG Pins)
Positive Input Terminal (True Differential Input)
Negative Power Supply Terminal
Reference Voltage Terminal (Drive This Terminal with a Low Impedance Voltage Source to Level-Shift the Output)
Output Terminal
Positive Power Supply Terminal
Rev. 0 | Page 8 of 20
AD8236
TYPICAL PERFORMANCE CHARACTERISTICS
G = 5, +VS = 5 V, VREF = 2.5 V, RL = 100 kΩ tied to GND, TA = 25°C, unless otherwise noted.
GAIN = 5
700
NUMBER OF UNITS
600
500
400
300
100
–40
–20
0
20
1s/DIV
08000-060
5µV/DIV
0
08000-024
200
40
CMRR (µV/V)
Figure 8. 0.1 Hz to 10 Hz RTI Voltage Noise
Figure 5. Typical Distribution of CMRR, G = 5
GAIN = 200
NUMBER OF UNITS
800
600
400
–2000
–1000
0
1000
2000
3000
4000
VOSI (µV)
1s/DIV
08000-061
5µV/DIV
0
–4000 –3000
08000-025
200
Figure 9. 0.1 Hz to 10 Hz RTI Voltage Noise
Figure 6. Typical Distribution of Input Offset Voltage
140
1k
120
GAIN = 200
GAIN = 100
PSRR (dB)
GAIN = 5
GAIN = 200
BANDWIDTH
LIMITED
10
1
10
100
FREQUENCY (Hz)
1k
INTERNAL
CLIPPING
80
60
40
20
0
10k
Figure 7. Voltage Noise Spectral Density vs. Frequency
GAIN = 10
GAIN = 5
0.1
1
10
100
1k
FREQUNCY (Hz)
08000-035
100
08000-042
NOISE (nV/√Hz)
100
10k
Figure 10. Positive PSRR vs. Frequency, RTI,
VS = ±0.9 V, ±2.5 V, VREF = 0 V
Rev. 0 | Page 9 of 20
100k
AD8236
120
15
GAIN = 100
100
10
CMRR (µV/V)
5
60
0
40
–5
20
–10
0.1
1
10
100
1k
10k
–15
–40
100k
–20
0
FREQUENCY (Hz)
Figure 11. Negative PSRR vs. Frequency, RTI, VS = ±0.9 V, ±2.5 V, VREF = 0 V
50
GAIN = 100
30
60
GAIN = 200
GAIN = 100
40
GAIN = 10
20
GAIN (dB)
CMRR (dB)
120
GAIN = 200
40
80
10
GAIN = 5
0
–10
GAIN = 10
–20
08000-023
20
GAIN = 5
1
10
100
1k
–30
–40
100k
10k
10
100
10k
100k
1M
Figure 15. Gain vs. Frequency, VS = 1.8 V, 5 V
Figure 12. CMRR vs. Frequency, RTI
6
100
5
80
4
VOUT (V p-p)
120
60
1k
FREQUENCY (Hz)
FREQUENCY (Hz)
GAIN = 200
GAIN = 100
3
2
40
GAIN = 5
GAIN = 10
1
10
100
1k
10k
08000-132
1
20
08000-051
CMRR (dB)
100
60
100
0
0.1
80
Figure 14. Change in CMRR vs. Temperature, G = 5, Normalized at 25°C
120
0
0.1
20
40
60
TEMPERATURE (°C)
0
100k
1
FREQUENCY (Hz)
10
100
1k
FREQUENCY (Hz)
10k
Figure 16. Maximum Output Voltage vs. Frequency
Figure 13. CMRR vs. Frequency, 1 kΩ Source Imbalance, RTI
Rev. 0 | Page 10 of 20
100k
08000-022
0
08000-040
PSRR (dB)
GAIN = 200
GAIN = 5
08000-014
GAIN = 10
80
AD8236
08000-026
RLOAD = 10kΩ TIED TO GND
VS = 5V
0.5
1.0
1.5
2.0
2.5
3.0
OUTPUT VOLTAGE (V)
3.5
4.0
4.5
(4.98V, 4.737V)
(0.01V, 4.24V)
4.0
3.5
3.0
2.5
2.0
1.5
1.0
(4.98V, 0.767V)
(0.01V, 0.27V)
0.5
0
–0.5
4.5
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
OUTPUT VOLTAGE (V)
Figure 17. Gain Nonlinearity, G = 5
08000-036
RLOAD = 100kΩ TIED TO GND
INPUT COMMON-MODE VOLTAGE (V)
NONLINEARITY (5ppm/DIV)
5.0
Figure 20. Input Common-Mode Voltage Range vs. Output Voltage,
G = 5, VS = 5 V, VREF = 2.5 V
VS = 5V
0.5
1.0
1.5
2.0
2.5
3.0
OUTPUT VOLTAGE (V)
3.5
4.0
4.5
(4.994V, 4.75V)
(0.01V, 4.25V)
4.0
3.5
3.0
2.5
2.0
1.5
1.0
(4.994V, 0.076V)
(0.01V, 0.026V)
0.5
0
–0.5
4.5
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
OUTPUT VOLTAGE (V)
Figure 18. Gain Nonlinearity, G = 10
08000-038
08000-028
TWO CURVES REPRESENTED:
RLOAD = 10kΩ AND 100kΩ TIED TO GND
INPUT COMMON-MODE VOLTAGE (V)
NONLINEARITY (2ppm/DIV)
5.0
Figure 21. Input Common-Mode Voltage Range vs. Output Voltage,
G = 200, VS = 5 V, VREF = 2.5 V
VS = 5V
0.5
1.0
1.5
2.0
2.5
3.0
OUTPUT VOLTAGE (V)
3.5
4.0
1.6
1.2
1.0
0.8
0.6
0.4
(1.78V, 0.274V)
(0.0069V, 0.09V)
0.2
0
–0.2
4.5
(1.78V, 1.704V)
(0.0069V, 1.52V)
1.4
0
0.2
0.4
0.6
0.8
1.0
1.2
OUTPUT VOLTAGE (V)
1.4
1.6
1.8
2.0
08000-037
08000-029
TWO CURVES REPRESENTED:
RLOAD = 10kΩ AND 100kΩ TIED TO GND
INPUT COMMON-MODE VOLTAGE (V)
NONLINEARITY (2ppm/DIV)
1.8
Figure 22. Input Common-Mode Voltage Range vs. Output Voltage,
G = 5, VS = 1.8 V, VREF = 0.9 V
Figure 19. Gain Nonlinearity, G = 200
Rev. 0 | Page 11 of 20
AD8236
1.6
(1.75V, 1.705V)
(0.03V, 1.533V)
1.4
1.2
2V/DIV
1.0
0.8
444μs TO 0.01%
0.6
0.4
(1.75V, 0.275V)
0
–0.2
0
0.2
0.4
08000-047
(0.03V, 0.103V)
0.2
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
OUTPUT VOLTAGE (V)
08000-039
INPUT COMMON-MODE VOLTAGE (V)
1.8
1ms/DIV
Figure 26. Large Signal Pulse Response and Settling Time,
VS = ±2.5 V, VREF = 0 V, RL = 10 kΩ to VREF
Figure 23. Input Common-Mode Voltage Range vs. Output Voltage,
G = 200, VS = 1.8 V, VREF = 0.9 V
+VS
–0.002
–0.003
+125°C
+85°C
–40°C
+25°C
700mV/DIV
143.2μs TO 0.01%
+0.003
+0.002
+125°C +85°C +25°C
–40°C
08000-048
OUTPUT VOLTAGE SWING (V)
REFERRED TO SUPPLY VOLTAGE
–0.001
–VS
1.8
2.3
2.8
3.3
3.8
4.3
SUPPLY VOLTAGE (V)
4.8
08000-054
+0.001
1ms/DIV
Figure 27. Large Signal Pulse Response and Settling Time,
VS = ±0.9 V, VREF = 0 V, RL = 10 kΩ to VREF
Figure 24. Output Voltage Swing vs. Supply Voltage,
VS = ±0.9 V, ±2.5 V, VREF = 0 V, RL = 100 kΩ Tied to −VS
+VS
+25°C
+85°C
+125°C
–0.2
20mV/DIV
–0.3
–40°C
+0.003
+125°C
+85°C
+25°C
–40°C
+0.001
–VS
08000-117
+0.002
03579-056
OUTPUT VOLTAGE SWING (V)
REFERRED TO SUPPLY VOLTAGE
–0.1
1k
10k
100k
100µs/DIV
RLOAD (Ω)
Figure 28. Small Signal Pulse Response, G = 5,
VS = ±2.5 V, VREF = 0 V, RL = 100 kΩ to VREF, CL = 100 pF
Figure 25. Output Voltage Swing vs. Load Resistance,
VS = ±0.9 V, ±2.5 V, VREF = 0 V, RL = 100 kΩ Tied to −VS
Rev. 0 | Page 12 of 20
AD8236
500
20mV/DIV
SETTLING TIME (µs)
400
300
200
0
100µs/DIV
0
1
2
08000-043
08000-017
100
4
3
OUTPUT VOLTAGE STEP SIZE (V)
Figure 29. Small Signal Pulse Response, G = 5, CL = 100 pF,
VS = ±0.9 V, VREF = 0 V, RL = 100 kΩ to VREF
Figure 32. Settling Time vs. Output Voltage Step Size,
VS = ±2.5 V, VREF = 0 V, RL = 10 kΩ Tied to VREF
40
38
20mV/DIV
SUPPLY CURRENT (µA)
36
1.8V
34
32
30
5V
28
26
08000-034
08000-113
24
22
20
–40
1ms/DIV
–25
–10
5
20
35
50
65
TEMPERATURE (°C)
80
95
Figure 33. Total Supply Current vs. Temperature
08000-013
20mV/DIV
Figure 30. Small Signal Pulse Response, G = 200,
CL = 100 pF, VS = 2.5 V, VREF = 0 V, RL = 100 kΩ to VREF
1ms/DIV
Figure 31. Small Signal Pulse Response, G = 200,
CL = 100 pF, VS = 0.9 V, VREF = 0 V, RL = 100 kΩ to VREF
Rev. 0 | Page 13 of 20
110
125
AD8236
THEORY OF OPERATION
RG
ESD
PROTECTION
ESD
PROTECTION
REF 6
210kΩ
52.5kΩ
RG
RG
3
+VS
–VS
8
5
ESD
PROTECTION
52.5kΩ
210kΩ
OP AMP
A
OP AMP
B
ESD
PROTECTION
ESD
PROTECTION
1
4
ESD
PROTECTION
7
VOUT
08000-006
2
AD8236
+IN
–IN
Figure 34. Simplified Schematic
The AD8236 is a monolithic, 2-op-amp instrumentation
amplifier. It was designed for low power, portable applications
where size and low quiescent current are paramount. For example,
it has a rail-to-rail input and output stage to offer more dynamic
range when operating on low voltage batteries. Unlike traditional
rail-to-rail input amplifiers that use a complementary differential
pair stage and suffer from nonlinearity, the AD8236 uses a novel
architecture to internally boost the supply rail, allowing the
amplifier to operate rail to rail yet still deliver a low 0.5 ppm of
nonlinearity. In addition, the 2-op-amp instrumentation amplifier
architecture offers a wide operational common-mode voltage
range. Additional information is provided in the CommonMode Input Voltage Range section. Precision, laser-trimmed
resistors provide the AD8236 with a high CMRR of 86 dB
(minimum) at G = 5 and gain accuracy of 0.05% (maximum).
BASIC OPERATION
The AD8236 amplifies the difference between its positive input
(+IN) and its negative input (−IN). The REF pin allows the user
to level-shift the output signal. This is convenient when interfacing
to a filter or analog-to-digital converter (ADC). The basic setup
is shown in Figure 35. Figure 37 shows an example configuration
for operating the AD8236 with dual supplies. The equation for
the AD8236 is as follows:
VOUT = G × (VINP − VINM) + VREF
GAIN SELECTION
Placing a resistor across the RG terminals sets the gain of the
AD8236, which can be calculated by referring to Table 6 or by
using the gain equation
RG =
1% Standard Table Value of RG (Ω)
422 k
210 k
140 k
105 k
84.5 k
28 k
9.31 k
4.42 k
2.15 k
0.1µF
VINM
+VS
RG
RG
–IN
AD8236
OUT
VOUT
REF
–VS
VREF
08000-136
VINP
Calculated Gain
6.0
7.0
8.0
9.0
10.0
20.0
50.1
100.0
200.3
The AD8236 defaults to G = 5 when no gain resistor is used.
Gain accuracy is determined by the absolute tolerance of RG.
The TC of the external gain resistor increases the gain drift of
the instrumentation amplifier. Gain error and gain drift are at a
minimum when the gain resistor is not used.
5V
GAIN SETTING
RESISTOR
G −5
Table 6. Gains Achieved Using 1% Resistors
If no gain setting resistor is installed, the default gain, G, is 5.
The Gain Selection section describes how to program the gain, G.
+IN
420 kΩ
Figure 35. Basic Setup
Rev. 0 | Page 14 of 20
AD8236
INCORRECT
LAYOUT
Careful board layout maximizes system performance. In
applications that need to take advantage of the low input
bias current of the AD8236, avoid placing metal under the
input path to minimize leakage current.
CORRECT
AD8236
AD8236
REF
REF
V
V
Grounding
+
REFERENCE TERMINAL
The reference terminal, REF, is at one end of a 210 kΩ resistor
(see Figure 34). The output of the instrumentation amplifier
is referenced to the voltage on the REF terminal; this is useful
when the output signal needs to be offset to voltages other than
common. For example, a voltage source can be tied to the REF
pin to level-shift the output so that the AD8236 can interface
with an ADC. The allowable reference voltage range is a function
of the gain, common-mode input, and supply voltages. The REF
pin should not exceed either +VS or −VS by more than 0.5 V.
08000-137
–
Figure 36. Driving the REF Pin
POWER SUPPLY REGULATION AND BYPASSING
The AD8236 has high power supply rejection ration (PSRR).
However, for optimal performance, a stable dc voltage should be
used to power the instrumentation amplifier. Noise on the supply
pins can adversely affect performance. As in all linear circuits,
bypass capacitors must be used to decouple the amplifier.
A 0.1 μF capacitor should be placed close to each supply pin.
A 10 μF tantalum capacitor can be used further away from the
part (see Figure 37). In most cases, it can be shared by other
precision integrated circuits.
For best performance, especially in cases where the output is not
measured with respect to the REF terminal, source impedance to
the REF terminal should be kept low because parasitic resistance
can adversely affect CMRR and gain accuracy. Figure 36
demonstrates how an op amp is configured to provide a low
source impedance to the REF terminal when a midscale
reference voltage is desired.
+VS
0.1µF
10µF
+IN
VOUT
AD8236
LOAD
REF
–IN
0.1µF
–VS
10µF
08000-138
The output voltage of the AD8236 is developed with respect to
the potential on the reference terminal, REF. To ensure the most
accurate output, the trace from the REF pin should either be
connected to the AD8236 local ground (see Figure 37) or
connected to a voltage that is referenced to the AD8236 local
ground (Figure 35).
OP AMP
Figure 37. Supply Decoupling, REF, and Output Referred to Ground
Rev. 0 | Page 15 of 20
AD8236
+VS
+VS
AD8236
AD8236
REF
REF
–VS
–VS
TRANSFORMER
TRANSFORMER
+VS
+VS
C
C
1
fHIGH-PASS = 2πRC
AD8236
R
AD8236
REF
REF
R
–VS
AC-COUPLED
08000-139
–VS
AC-COUPLED
Figure 38. Creating an IBIAS Path
INPUT BIAS CURRENT RETURN PATH
RF INTERFERENCE
The AD8236 input bias current is extremely small at less than
10 pA. Nonetheless, the input bias current must have a return
path to common. When the source, such as a transformer,
cannot provide a return current path, one should be created
(see Figure 38).
RF rectification is often a problem in applications where there are
large RF signals. The problem appears as a small dc offset voltage.
The AD8236, by its nature, has a 3.1 pF gate capacitance, CG, at
each input. Matched series resistors form a natural low-pass filter
that reduces rectification at high frequency (see Figure 39). The
relationship between external, matched series resistors and the
internal gate capacitance is expressed as
All terminals of the AD8236 are protected against ESD. In
addition, the input structure allows for dc overload conditions
a diode drop above the positive supply and a diode drop below
the negative supply. Voltages beyond a diode drop of the supplies
cause the ESD diodes to conduct and enable current to flow
through the diode. Therefore, an external resistor should be
used in series with each of the inputs to limit current for
voltages above +VS. In either scenario, the AD8236 safely
handles a continuous 6 mA current at room temperature.
For applications where the AD8236 encounters extreme
overload voltages, as in cardiac defibrillators, external series
resistors and low leakage diode clamps, such as BAV199Ls,
FJH1100s, or SP720s, should be used.
FilterFreqDIFF =
FilterFreqCM =
1
2πRCG
1
2πRCG
+VS
0.1µF
R
10µF
+IN
CG
AD8236
–VS
R
VOUT
CG
–IN
–VS
0.1µF
REF
10µF
–VS
08000-140
INPUT PROTECTION
Figure 39. RFI Filtering Without External Capacitors
Rev. 0 | Page 16 of 20
AD8236
To eliminate high frequency common-mode signals while using
smaller source resistors, a low-pass RC network can be placed
at the input of the instrumentation amplifier (see Figure 40).
The filter limits the input signal bandwidth according to the
following relationship:
FilterFreqDIFF =
FilterFreqCM =
1
2πR(2 CD + CC + CG )
COMMON-MODE INPUT VOLTAGE RANGE
The common-mode input voltage range is a function of the
input voltages, reference voltage, supplies, and the output of
Internal Op Amp A. Figure 34 shows the internal nodes of the
AD8236. Figure 20 to Figure 23 show the common-mode
voltage ranges for typical supply voltages and gains.
If the supply voltages and reference voltage is not represented in
Figure 20 to Figure 23, the following methodology can be used
to calculate the acceptable common-mode voltage range:
1
2πR(CC + CG )
Mismatched CC capacitors result in mismatched low-pass filters.
The imbalance causes the AD8236 to treat what would have been
a common-mode signal as a differential signal. To reduce the
effect of mismatched external CC capacitors, select a value of CD
greater than 10 times CC. This sets the differential filter frequency
lower than the common-mode frequency.
1.
2.
5
V
A = ⎛⎜ VCM − DIFF
4⎝
2
+VS
0.1µF
CC
+IN
4.02kΩ
CD
VOUT
AD8236
10nF
R
If no gain setting resistor, RG, is installed, set RG to infinity.
REF
3.
–IN
4.02kΩ
1nF
08000-141
CC
VREF
⎞ − 52.5 kΩ V
⎟
DIFF −
RG
4
⎠
where:
VDIFF is defined as the difference in input voltages,
VDIFF = VINP − VINM.
VCM is defined as the common mode voltage,
VCM = (VINP + VINM)/2.
10µF
1nF
R
Adhere to the input, output, and reference voltage ranges
shown in Table 2 and Table 3.
Calculate the output of the internal op amp, A. The following
equation calculates this output:
Keep A within 10 mV of either supply rail. This is valid over
the −40°C to +125°C temperature range.
−VS + 10 mV < A < +VS – 10 mV
Figure 40. RFI Suppression
Rev. 0 | Page 17 of 20
AD8236
APPLICATIONS INFORMATION
+VS
AC-COUPLED INSTRUMENTATION AMPLIFIER
When a signal exceeds fHIGH-PASS, the AD8236 outputs the highpass filtered input signal.
0.1µF
+IN
fHIGH-PASS =
1
2πRC
AD8236
R
REF
–IN
C
+VS
0.1µF
AD8603
+VS
VREF
10µF
Figure 41. AC-Coupled Circuit
Rev. 0 | Page 18 of 20
08000-142
An integrator can be tied to the AD8236 in feedback to create a
high-pass filter as shown in Figure 41. This circuit can be used
to reject dc voltages and offsets. At low frequencies, the impedance
of the capacitor, C, is high. Therefore, the gain of the integrator
is high. DC voltage at the output of the AD8236 is inverted and
gained by the integrator. The inverted signal is injected back into
the REF pin, nulling the output. In contrast, at high frequencies,
the integrator has low gain because the impedance of C is low.
Voltage changes at high frequencies are inverted but at a low
gain. The signal is injected into the REF pins, but it is not enough to
null the output. At very high frequencies, the capacitor appears as
a short. The op amp is at unity gain. High frequency signals are,
therefore, allowed to pass.
AD8236
This circuit was designed and tested using the AD8609, low
power, quad op amp. The fourth op amp is configured as a Schmitt
trigger to indicate if the right arm or left arm electrodes fall off
the body. Used in conjunction with the 953 kΩ resistors at the
inputs of the AD8236, the resistors pull the inputs apart when
the electrodes fall off the body. The Schmitt trigger sends an
active low signal to indicate a leads off condition.
LOW POWER HEART RATE MONITOR
The low power and small size of the AD8236 make it an
excellent choice for heart rate monitors. As shown in Figure 42,
the AD8236 measures the biopotential signals from the body.
It rejects common-mode signals and serves as the primary gain
stage set at G = 5. The 4.7 μF capacitor and the 100 kΩ resistor
set the −3 dB cutoff of the high-pass filter that follows the
instrumentation amplifier. It rejects any differential dc offsets
that may develop from the half-cell overpotential of the electrode.
The reference electrode (right leg) is set tied to ground. Likewise,
the shield of the electrode cable is also tied to ground. Some
portable heart rate monitors do not have a third electrode. In
such cases, the negative input of the AD8236 can be tied to GND.
A secondary gain stage, set at G = 403, amplifies the ECG signal,
which is then sent into a second-order, low-pass, Bessel filter
with −3 dB cutoff at 48 Hz. The 324 Ω resistor and 1 μF capacitor
serve as an antialiasing filter. The 1 μF capacitor also serves as a
charge reservoir for the ADC’s switched capacitor input stage.
Note that this circuit is shown, solely, to demonstrate the capability
of the AD8236. Additional effort must be made to ensure
compliance with medical safety guidelines.
+2.5V
–2.5V
1kΩ
+2.5V
20kΩ
5kΩ
+2.5V
0.1µF
AD8609
LEADS OFF DETECTION
INTERRUPT
LEADS OFF
680nF
953kΩ
+2.5V
0.1µF
RL
AD8236
LA
IN-AMP
AD8609
24.9kΩ
4.02kΩ
AD8609
100kΩ
953kΩ
1kΩ
0.1µF
402kΩ
220nF
0.1µF
324Ω
1µF
10-BIT ADC
MCU + ADC
4.7µF
–2.5V
–2.5V
–2.5V
+2.5V
AD8609
1kΩ
08000-143
RA
–2.5V
Figure 42. Example Low Power Heart Rate Monitor Schematic
Rev. 0 | Page 19 of 20
AD8236
OUTLINE DIMENSIONS
3.20
3.00
2.80
8
3.20
3.00
2.80
1
5
5.15
4.90
4.65
4
PIN 1
0.65 BSC
0.95
0.85
0.75
1.10 MAX
0.15
0.00
0.38
0.22
COPLANARITY
0.10
0.23
0.08
8°
0°
0.80
0.60
0.40
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-187-AA
Figure 43. 8-Lead Mini Small Outline Package [MSOP]
(RM-8)
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD8236ARMZ 1
AD8236ARMZ-R71
AD8236ARMZ-RL1
1
Temperature Range
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
Package Description
8-Lead MSOP
8-Lead MSOP
8-Lead MSOP
Z = RoHS Compliant Part.
©2009 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D08000-0-5/09(0)
Rev. 0 | Page 20 of 20
Package Option
RM-8
RM-8
RM-8
Branding
Y1W
Y1W
Y1W