2W005G THRU 2W10G GLASS PASSIVATED BRIDGE RECTIFIERS Reverse Voltage – 50 to 1000 Volts Forward Current – 2.0 Amperes Features • • • • Rating to 1000V PRV Ideal for printed circuit board Low forward voltage drop, high current capability. Reliable low cost construction utilizing molded epoxy technique results in inexpensive product Mechanical Data • • • Case: Molded plastic Polarity: As marked on Body Mounting position: Any Aboslute Maximum Ratings and Characteristics o Ratings at 25 Cambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. Symbols 2W005G 2W01G 2W02G 2W04G 2W06G 2W08G 2W10G Units Maximum recurrent peak reverse voltage VRRM 50 100 200 400 600 800 1000 V Maximum RMS voltage VRMS 35 70 140 280 420 560 700 V Maximum DC blocking voltage VDC 50 100 200 400 600 800 1000 V Maximum average forward rectified current at TA = 25 OC I(AV) 2 A Peak forward surge current , 8.3ms single half sine-wave superimposed on rated load (JEDEC METHOD) IFSM 60 A VF 1.1 V IR 5 500 µA CJ 25 pF RθJA 40 Operating temperature range TJ -55 to +150 O C Storage temperature range TS -55 to +150 O C Maximum forward voltage at 2.0A DC Maximum DC reverse current at rated DC blocking voltage @ TJ = 25 OC @ TJ =125 OC Typical junction capacitance per element (Note 1) Typical thermal resistance (Note 2) Notes: o (1) Measured at 1MHz and appliad reverse voltage of 4V DC. (2) Thermal resistance junction to ambient. SEMTECH ELECTRONICS LTD. ® (Subsidiary of Semtech International Holdings Limited, acompany listed on the Hong Kong Stock Exchange, Stock Code: 724) Dated : 23/06/2003 C/W 2W005G THRU 2W10G FIG.1-FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT AMPERES 3.0 2.5 2.0 1.5 1.0 SINGLE PHASE HALF WAVE 60Hz RESISTIVE OR INDUCTIVE LOAD 0.5 0 25 75 50 PEAK FORWARD SURGE CURRENT AMPERES RATINGS AND CHARACTERISTIC CURVES (2W005G THRU 2W10G) 100 125 150 175 AMBIENT TEMPERATURE. FIG.2-MAXIMUM NON-REPETITIVE SURGE CURRENT 60 50 40 30 20 10 0 1 5 2 ( oC) 10 20 50 100 NUMBER OF CYCLES AT 60Hz FIG.3-TYPICAL, JUNCTION CAPACITANCE FIG.4-TYPICAL FORWARD CHARACTERISTICS 10 INSTANTANEOUS FORWARD CURRENT.(A) 100 CAPACITANCE.(pF) SINGLE HALF SINE-WAVE (JEDEC METHOD) 10 1.0 Vsig=50mV p-p o TJ =25 C ,f=1MHz 1 4 100 10 REVERSE VOLTAGE , VOLTS 1.0 TJ =25 o C 0.1 0.01 0 PULSE WIDTH 300 s 2% DUTY CYCLE 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG.5-TYPICAL REVERSE CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT. ( µ A) 100 TJ =125 oC 10 1.0 0.1 TJ =25 o C 0.01 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE.(%) SEMTECH ELECTRONICS LTD. ® (Subsidiary of Semtech International Holdings Limited, acompany listed on the Hong Kong Stock Exchange, Stock Code: 724) Dated : 23/06/2003