AD ADM8839

Charge Pump Regulator
for Color TFT Panels
ADM8839
FEATURES
3 Voltages (+5 V, +15 V, –15 V) from
a Single 3 V Supply
Power Efficiency Optimized for Use
with TFT in Mobile Phones
Low Quiescent Current
Low Shutdown Current (<5 A)
Shutdown Function
Option to Use External LDO
APPLICATIONS
Hand-held Instruments
TFT LCD Panels
Cellular Phones
FUNCTIONAL BLOCK DIAGRAM
C5, 2.2␮F
VCC
C1+
ADM8839
VOLTAGE
DOUBLER
C1–
C1, 2.2␮F
VOUT
LDO_IN
OSCILLATOR
LDO_ON/OFF
LDO
VOLTAGE
REGULATOR
CONTROL
LOGIC
DOUBLE
VOLTAGE
TRIPLER
TRIPLE
TIMING
GENERATOR
C6, 2.2␮F
+5VOUT
+5VIN
C2–
C2, 0.22␮F
C3+
C3–
C3, 0.22␮F
+15VOUT
SHUTDOWN
CONTROL
DISCHARGE
VOLTAGE
INVERTER
C4–
C4, 0.22␮F
–15VOUT
GND
GENERAL DESCRIPTION
The ADM8839 is a charge pump regulator used for color thin film
transistor (TFT) liquid crystal displays (LCDs). Using charge
pump technology, the device can be used to generate three
voltages (+5 V ± 2%, +15 V, –15 V) from a single 3 V supply.
These voltages are then used to provide supplies for the LCD
controller (5 V) and the gate drives for the transistors in the
panel (+15 V and –15 V). Only a few external capacitors are
needed for the charge pumps. An efficient low dropout (LDO)
voltage regulator ensures that the power efficiency is high and
provides a low ripple 5 V output. This LDO can be shut down
and an external LDO can be used to regulate the 5 V doubler
output and drive the input to the charge pump section that
generates the +15 V and –15 V outputs, if required by the user.
+15V
C8, 0.22␮F
C4+
SHDN
+5V
C7, 2.2␮F
C2+
–15V
C9, 0.22␮F
The ADM8839 has a power save shutdown feature. The 5 V
output consumes the most power, so power efficiency is also
maximized on this output with an oscillator enabling scheme
(Green Idle™). This effectively senses the load current that is
flowing and turns on the charge pump only when charge needs
to be delivered to the 5 V pump doubler output.
The ADM8839 is fabricated using CMOS technology for minimal
power consumption. The part is packaged in a 20-lead LFCSP
(lead frame chip scale package).
REV. A
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties that
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective companies.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
www.analog.com
Fax: 781/326-8703
© 2003 Analog Devices, Inc. All rights reserved.
ADM8839–SPECIFICATIONS
Parameter
(VCC = 3 V – 10%, 40%; TA = –40C to +85C; C1, C5, C6, C7 = 2.2 F; C2, C3,
C4, C8, C9 = 0.22 F; unless otherwise noted.)
Test Conditions
Min
INPUT VOLTAGE, VCC
SUPPLY CURRENT, ICC
+5 V OUTPUT
Output Voltage
Output Current
Output Ripple
Transient Response
+15 V OUTPUT
Output Voltage
Output Current
Output Ripple
–15 V OUTPUT
Output Voltage
Output Current
Output Ripple
POWER EFFICIENCY
Max
Unit
4.2
V
250
500
5
␮A
␮A
4.9
5.0
5
10
5
5.1
8
V
mA
mV p-p
␮s
14.0
15.0
1
50
16.0
150
V
␮A
mV p-p
–16.0
–150
–15.0
–1
50
–14.0
V
␮A
mV p-p
2.7
Unloaded
Shutdown Mode, TA = 25°C
IL = 10 ␮A to 8 mA
8 mA Load
IL Stepped from 10 ␮A to 8 mA
IL = 1 ␮A to 150 ␮A
IL = 100 ␮A
IL = –1 ␮A to –150 ␮A
IL = –100 ␮A
R5VOUT Load = 5 mA,
⫾15 V Load = ⫾150 ␮A,
VCC = 3.0 V
CHARGE PUMP FREQUENCY
CONTROL PINS, SHDN
Input Voltage, VSHDN
Typ
82
60
SHDN Low = Shutdown Mode
SHDN High = Normal Mode
100
0.7 ⫻ VCC
Low = External LDO
High = Internal LDO
140
kHz
0.3 ⫻ VCC
V
V
␮A
pF
⫾1
10
Digital Input Current
Digital Input Capacitance*
LDO_ON/OFF
Input Voltage
%
0.3 ⫻ VCC
0.7 ⫻ VCC
⫾1
10
Digital Input Current
Digital Input Capacitance*
V
V
␮A
pF
*Guaranteed by design. Not 100% production tested.
Specifications are target values and are subject to change without notice.
TIMING SPECIFICATIONS
Parameter
POWER-UP SEQUENCE
+5 V Rise Time, tR5V
+15 V Rise Time, tR15V
–15 V Fall Time, tFM15V
Delay between –15 V Fall
and +15 V, tDELAY
POWER-DOWN SEQUENCE
+5 V Fall Time, tF5V
+15 V Fall Time, tF15V
–15 V Rise Time, tRM15V
(VCC = 3 V, TA = 25C; C1, C5, C6, C7 = 2.2 F; C2, C3, C4, C8, C9 = 0.22 F.)
Test Conditions/Comments
Min
Typ
Max
Unit
10% to 90%, Figure 1
10% to 90%, Figure 1
90% to 10%, Figure 1
250
3
3
␮s
ms
ms
Figure 1
600
␮s
90% to 10%, Figure 1
90% to 10%, Figure 1
10% to 90%, Figure 1
35
10
20
ms
ms
ms
Specifications are subject to change without notice.
–2–
REV. A
ADM8839
ABSOLUTE MAXIMUM RATINGS*
THERMAL CHARACTERISTICS
(TA = 25°C, unless otherwise noted.)
20-Lead LFCSP Package:
␪JA = 31°C/W
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +6.0 V
Input Voltage on Digital Inputs . . . . . . . . . . . –0.3 V to +6.0 V
Output Short-Circuit Duration to GND . . . . . . . . . . . . . 10 sec
Output Voltage
+5 V Output . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 V to 7.0 V
–15 V Output . . . . . . . . . . . . . . . . . . . . . . . . –17 V to +0.3 V
+15 V Output . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +17 V
Operating Temperature Range . . . . . . . . . . . . –40°C to +85°C
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mW
Storage Temperature Range . . . . . . . . . . . . . –65°C to +150°C
ESD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class I
ORDERING GUIDE
Model
Temperature Range
Package Option
ADM8839ACP
–40°C to +85°C
CP-20
*Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although the
ADM8839 features proprietary ESD protection circuitry, permanent damage may occur on devices
subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended
to avoid performance degradation or loss of functionality.
REV. A
–3–
ADM8839
20 C1
19 C1
18 GND
17 15VOUT
16 C4
PIN CONFIGURATION
PIN 1
INDICATOR
ADM8839
TOP VIEW
15 C4
14 C2
13 C2
12 C3
11 C3
LDO_ON/OFF 6
SHDN 7
VCC 8
GND 9
15VOUT 10
VCC 1
VOUT 2
LDO_IN 3
5VOUT 4
5VIN 5
PIN FUNCTION DESCRIPTIONS
Pin No.
Mnemonic
Function
1
VCC
Positive Supply Voltage Input. Connect this pin to the 3 V supply with a 2.2 µF decoupling capacitor.
2
VOUT
Voltage Doubler Output. This was derived by doubling the 3 V supply. A 2.2 µF capacitor to
ground is required on this pin.
3
LDO_IN
Voltage Regulator Input. The user may bypass this circuit by using the LDO_ON/OFF pin.
4
+5VOUT
5 V Output. This was derived by doubling and regulating the 3 V supply. A 2.2 µF capacitor
to ground is required on this pin to stabilize the regulator.
5
+5VIN
5 V Input. This is the input to the voltage tripler and inverter charge pump circuits.
6
LDO_ON/OFF
Control Logic Input. 3 V CMOS logic. A logic high selects the internal LDO for regulation of
the 5 V voltage doubler output. A logic low isolates the internal LDO from the rest of the charge
pump circuits. This allows the use of an external LDO to regulate the 5 V voltage doubler
output. The output of this LDO is then fed back into the voltage tripler and inverter circuits of
the ADM8839.
7
SHDN
Digital Input. 3 V CMOS logic. Active low shutdown control. This shuts down the timing
generator and enables the discharge circuit to dissipate the charge on the voltage outputs, thus
driving them to 0 V.
8
VCC
Connect this pin to VCC.
9
GND
Connect this pin to GND.
10
+15VOUT
15 V Output. This was derived by tripling the 5 V regulated output. A 0.22 µF capacitor
is required on this pin.
11, 12
C3–, C3+
External capacitor C3 is connected between these pins. A 0.22 µF capacitor is recommended.
13, 14
C2–, C2+
External capacitor C2 is connected between these pins. A 0.22 µF capacitor is recommended.
15, 16
C4–, C4+
External capacitor C4 is connected between these pins. A 0.22 µF capacitor is recommended.
17
–15VOUT
–15 V Output. This was derived by tripling and inverting the 5 V regulated output. A 0.22 µF
capacitor is required on this pin.
18
GND
Device Ground.
19, 20
C1–, C1+
External capacitor C1 is connected between these pins. A 2.2 µF capacitor is recommended.
–4–
REV. A
Typical Performance Characteristics–ADM8839
5.10
84
DEVICE AT +25C
83
LDO POWER EFFICIENCY – %
5.05
DEVICE AT +85C
LDO O/P VOLTAGE – V
5.00
4.95
DEVICE AT –40C
4.90
4.85
4.80
4.75
81
80
79
78
77
76
4.70
2.7
75
2.9
3.1
3.3
3.5
3.7
SUPPLY VOLTAGE – V
3.9
1
4.1 4.2
2
3
4
5
6
7
8
LOAD CURRENT – mA
TPC 1. LDO O/P Voltage Variation
over Temperature and Supply
TPC 4. LDO Power Efficiency vs. Load Current,
VCC = 3 V
5.020
400
5.015
350
SUPPLY CURRENT – A
LDO O/P VOLTAGE – V
82
5.010
5.005
5.000
300
250
200
4.995
0
1
2
3
4
5
6
7
150
2.7
8
2.9
3.1
3.3
3.5
3.7
3.9
4.1 4.2
ILOAD – mA
SUPPLY VOLTAGE – V
TPC 2. LDO O/P Voltage vs. Load Current
TPC 5. Supply Current vs. Supply Voltage
100
15.1
14.9
80
OUTPUT VOLTAGE – V
+15V/–15V POWER EFFICIENCY – %
15.0
90
70
60
50
14.8
+15V AT 25C
14.7
14.6
–15V AT 25C
14.5
14.4
14.3
40
14.2
30
14.1
10
20
30
40
50
60
70
80
90
0
100
TPC 3. +15 V/–15 V Power Efficiency vs. Load Current
REV. A
50
100
150
200
ILOAD – A
ILOAD – A
TPC 6. +15 V/–15 V Output Voltage vs. Load
Current, Typical Configuration
–5–
ADM8839
LOAD ENABLE
+15V OUTPUT
5V OUTPUT
–15V OUTPUT
5VOUT
TPC 10. Output Transient Response for
Maximum Load Current
TPC 7. +15 V and –15 V Outputs at Power-Up
VOUT RIPPLE (DOUBLER OUTPUT RIPPLE)
+15V OUTPUT
LDO OUTPUT RIPPLE
VCC RIPPLE
–15V OUTPUT
5VOUT
TPC 8. Output Ripple on LDO (5 V Output)
TPC 11. +15 V and –15 V Outputs at Power-Down
LOAD DISABLE
5V OUTPUT
TPC 9. 5 V Output Transient Response,
Load Disconnected
–6–
REV. A
ADM8839
POWER SEQUENCING
In order for the TFT panel to power up correctly, the gate drive
supplies must be sequenced such that the –15 V supply is up
before the +15 V supply. The ADM8839 controls this sequence.
When the device is turned on (a logic high on SHDN), the
ADM8839 allows the –15 V output to ramp immediately but
holds off the +15 V output. It continues to do this until the
negative output has reached –3 V. At this point, the positive
output is enabled and allowed to ramp to +15 V. This sequence
is highlighted in Figure 1.
C5, 2.2F
VCC
C1+
ADM8839
VOLTAGE
DOUBLER
C1, 2.2F
VOUT
LDO_IN
OSCILLATOR
LDO_ON/OFF
LDO
VOLTAGE
REGULATOR
CONTROL
LOGIC
DOUBLE
VOLTAGE
TRIPLER
+5VOUT
TIMING
GENERATOR
+5V
C7, 2.2F
C2+
C2–
TRIPLE
SHDN
C6, 2.2F
+5VIN
VCC
C2, 0.22F
C3+
C3–
C3, 0.22F
+15VOUT
tR5V
+15V
C8, 0.22F
90%
+5V
C1–
C4+
tF5V
10%
SHDN
SHUTDOWN
CONTROL
DISCHARGE
VOLTAGE
INVERTER
tR15V
C4–
C4, 0.22F
–15VOUT
–15V
90%
+15V
tF15V
10%
C9, 0.22F
GND
tDELAY
Figure 2. Typical Configuration
–15V
–3V
90%
15.1
tRM15V
10%
15.0
tFM15V
14.9
OUTPUT VOLTAGE – V
Figure 1. Power Sequence
TRANSIENT RESPONSE
The ADM8839 features extremely fast transient response, making it very suitable for fast image updates on TFT LCD panels.
This means that even under changing load conditions, there is
still very effective regulation of the 5 V output. TPCs 9 and 10
show how the 5 V output responds when a maximum load is
dynamically connected and disconnected. Note that the output
settles within 5 µs to less than 1% of the output level.
14.8
+15V AT 25C
14.7
14.6
–15V AT 25C
14.5
14.4
14.3
14.2
14.1
0
BOOSTING THE CURRENT DRIVE OF THE 15 V SUPPLY
100
150
200
ILOAD – A
The ADM8839 ⫾15 V output can deliver 150 µA of current in
the typical configuration, as shown in Figure 2. It is also possible to draw 100 µA from the +15 V output and 200 µA from
the –15 V output, or vice versa. It is possible to draw only a
maximum of 300 µA combined from both the +15 V and the
–15 V outputs at any time (see Figure 3). In this configuration,
+5VOUT (Pin 4) is connected to +5VIN (Pin 5), as shown in
the Functional Block Diagram.
REV. A
50
Figure 3. +15 V/–15 V Output Voltage vs. Load
Current, Typical Configuration
–7–
ADM8839
It is possible to configure the ADM8839 to supply up to 400 µA
on the ± 15 V outputs by changing its configuration slightly, as
shown in Figure 4.
The configuration in Figure 4 can supply up to 400 µA of current
on both the +15 V and the –15 V outputs. If the load on the
± 15 V does not draw any current, the voltage on the ± 15 V outputs can rise up to ± 16.5 V (see Figure 5). In this configuration,
VOUT (Pin 2) is connected to +5VIN (Pin 5).
C5, 2.2␮F
VCC
C1–
C1, 2.2␮F
OSCILLATOR
LDO
VOLTAGE
REGULATOR
CONTROL
LOGIC
16.5
CURRENT BOOST
CONFIGURATION
CONNECTION
OUTPUT VOLTAGE – V
VOLTAGE
DOUBLER
VOUT
LDO_IN
C6, 2.2␮F
+5VOUT
+5V
+5VIN
LDO_ON/OFF
C7, 2.2␮F
C2+
DOUBLE
VOLTAGE
TRIPLER
C2–
TIMING
GENERATOR
C3–
+15V AT 25ⴗC
16.0
–15V AT 25ⴗC
15.5
15.0
C2, 0.22␮F
14.5
C3+
TRIPLE
C3, 0.22␮F
14.0
+15VOUT
0
+15V
100
200
C8, 0.22␮F
SHDN
DISCHARGE
VOLTAGE
INVERTER
C4–
C4, 0.22␮F
–15VOUT
300
400
500
ILOAD – ␮A
C4+
SHUTDOWN
CONTROL
C03075–0–2/03(A)
17.0
C1+
ADM8839
Figure 5. +15 V/–15 V Output Voltage vs. Load
Current, Current Boost Configuration
–15V
C9, 0.22␮F
GND
Figure 4. Current Boost Configuration
OUTLINE DIMENSIONS
20-Lead Leadframe Chip Scale Package [LFCSP]
4 ⫻ 4 mm Body
(CP-20)
Dimensions shown in millimeters
0.60
MAX
0.60
MAX
PIN 1
INDICATOR
TOP
VIEW
12 MAX
1.00
0.90
0.80
SEATING
PLANE
0.50
BSC
16
15
3.75
BSC SQ
1
2.25
2.10 SQ
1.95
BOTTOM
VIEW
0.75
0.55
0.35
1.00 MAX
0.65 NOM
0.20
REF
20
0.05
0.02
0.00
11
10
6
5
0.30
0.23
0.18
COPLANARITY
0.08
COMPLIANT TO JEDEC STANDARDS MO-220-VGGD-1
Revision History
2/03 – Data Sheet Changed from Rev. 0 to Rev. A
Changed SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Updated OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
–8–
PRINTED IN U.S.A.
4.0
BSC SQ