BGA2716 MMIC wideband amplifier Rev. 02 — 24 September 2004 Product data sheet 1. Product profile 1.1 General description Silicon Monolithic Microwave Integrated Circuit (MMIC) wideband amplifier with internal matching circuit in a 6-pin SOT363 SMD plastic package. CAUTION This device is sensitive to electrostatic discharge (ESD). Therefore care should be taken during transport and handling. MSC895 1.2 Features ■ ■ ■ ■ ■ ■ ■ Internally matched to 50 Ω Wide frequency range (3.2 GHz at 3 dB bandwidth) Flat 23 dB gain (±1 dB up to 2.7 GHz) 9 dBm output power at 1 dB compression point Good linearity for low current (IP3out = 22 dBm) Low second harmonic; −38 dBc at PL = −5 dBm Unconditionally stable (K ≥ 1.2). 1.3 Applications ■ ■ ■ ■ LNB IF amplifiers Cable systems ISM General purpose. 1.4 Quick reference data Table 1: Quick reference data Symbol Parameter Min Typ Max Unit VS DC supply voltage - 5 6 V supply current - 15.9 - mA - 22.9 - dB IS s21 2 insertion power gain Conditions f = 1 GHz NF noise figure f = 1 GHz - 5.3 - dB PL(sat) saturated load power f = 1 GHz - 11.6 - dBm BGA2716 Philips Semiconductors MMIC wideband amplifier 2. Pinning information Table 2: Pinning Pin Description 1 VS 2, 5 GND2 3 RF_OUT 4 GND1 6 RF_IN Simplified outline 6 5 Symbol 1 4 6 3 4 2, 5 sym052 1 2 3 SOT363 3. Ordering information Table 3: Ordering information Type number BGA2716 Package Name Description Version - plastic surface mounted package; 6 leads SOT363 4. Marking Table 4: Marking Type number Marking code BGA2716 B7- 5. Limiting values Table 5: Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter Conditions Min Max Unit VS DC supply voltage RF input AC coupled - 6 V IS supply current - 30 mA Ptot total power dissipation - 200 mW Tsp ≤ 90 °C Tstg storage temperature −65 +150 °C Tj junction temperature - 150 °C PD maximum drive power - −10 dBm 9397 750 13292 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 02 — 24 September 2004 2 of 14 BGA2716 Philips Semiconductors MMIC wideband amplifier 6. Thermal characteristics Table 6: Thermal characteristics Symbol Parameter Conditions Typ Unit Rth(j-sp) thermal resistance from junction to solder point Ptot = 200 mW; Tsp ≤ 90 °C 300 K/W 7. Characteristics Table 7: Characteristics VS = 5 V; IS = 15.9 mA; Tj = 25 °C; measured on demo board; unless otherwise specified. Symbol Parameter IS s21 2 s112 s22 2 s122 Conditions Min Typ Max Unit supply current 13 15.9 21 mA insertion power f = 100 MHz gain f = 1 GHz 21 22.1 23 dB 22 22.9 24 dB f = 1.8 GHz 22 23.1 25 dB f = 2.2 GHz 21 22.8 24 dB f = 2.6 GHz 20 22.1 24 dB f = 3 GHz 19 20.8 22 dB input return losses f = 1 GHz 15 17 - dB f = 2.2 GHz 10 12 - dB output return losses f = 1 GHz 10 12 - dB f = 2.2 GHz 9 11 - dB isolation f = 1.6 GHz 30 31 - dB f = 2.2 GHz 33 35 - dB f = 1 GHz - 5.3 5.4 dB NF noise figure f = 2.2 GHz - 5.5 5.6 dB B bandwidth at s212 −3 dB below flat gain at 1 GHz 3 3.2 - GHz K stability factor f = 1 GHz - 1.4 - f = 2.2 GHz - 1.9 - PL(sat) saturated load power f = 1 GHz 10 11.6 - dBm f = 2.2 GHz 6 7.5 - dBm load power at 1 dB gain compression; f = 1 GHz 8 8.9 - dBm at 1 dB gain compression; f = 2.2 GHz 5 6.1 - dBm PL(1dB) IM2 second order at PL = −5 dBm; intermodulation f0 = 1 GHz product 36 38 - dBc IP3in input, third order intercept point f = 1 GHz −2 −0.7 - dBm f = 2.2 GHz −8 −6.9 - dBm output, third order intercept point f = 1 GHz 21 22.2 - dBm f = 2.2 GHz 15 15.9 - dBm IP3out 9397 750 13292 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 02 — 24 September 2004 3 of 14 BGA2716 Philips Semiconductors MMIC wideband amplifier 8. Application information Figure 1 shows a typical application circuit for the BGA2716 MMIC. The device is internally matched to 50 Ω, and therefore does not need any external matching. The value of the input and output DC blocking capacitors C2 and C3 should not be more than 100 pF for applications above 100 MHz. However, when the device is operated below 100 MHz, the capacitor value should be increased. The nominal value of the RF choke L1 is 100 nH. At the frequencies below 100 MHz this value should be increased. At frequencies above 1 GHz, a lower value can be used to tune the output return loss. For optimal results, a good quality chip inductor or a wire-wound SMD type should be chosen. Both the RF choke and the 22 nF supply decoupling capacitor C1 should be located as close as possible to the MMIC. The printed-circuit board (PCB) top ground plane, connected to pins 2, 4 and 5 must be as close as possible to the MMIC, and ideally directly beneath it. When using via holes, use multiple via holes, located as close as possible to the MMIC. VS C1 L1 VS C2 RF input RF_IN GND1 RF_OUT C3 RF output GND2 mgu436 Fig 1. Typical application circuit. Figure 2 shows the PCB layout, used for the standard demonstration board. 9397 750 13292 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 02 — 24 September 2004 4 of 14 BGA2716 Philips Semiconductors MMIC wideband amplifier 30 mm PHILIPS PH 30 mm IN OUT V+ PHILIPS PH DUT C3 C2 IN L1 C1 OUT V+ 001aab256 Material = FR4; thickness = 0.6 mm, εr = 4.6. Fig 2. PCB layout and demonstration board showing components. 8.1 Application examples The excellent wideband characteristics of the MMIC make it an ideal building block in IF amplifier such as LNBs (see Figure 3). 9397 750 13292 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 02 — 24 September 2004 5 of 14 BGA2716 Philips Semiconductors MMIC wideband amplifier As second amplifier after an LNA, the MMIC offers an easy matching, low noise solution (see Figure 4). As driver amplifier in the TX path, the good linear performance and matched input/output offer quick design solutions (see Figure 5). mixer to IF circuit or demodulator from RF circuit wideband amplifier oscillator mgu438 Fig 3. Application as IF amplifier. mixer to IF circuit or demodulator antenna LNA wideband amplifier oscillator mgu439 Fig 4. Application as RF amplifier. mixer from modulation or IF circuit to power amplifier wideband amplifier oscillator mgu440 Fig 5. Application as driver amplifier. 9397 750 13292 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 02 — 24 September 2004 6 of 14 BGA2716 Philips Semiconductors MMIC wideband amplifier 90° 1.0 +1 135° +0.5 0.8 45° +2 0.6 +0.2 0.4 +5 100 MHz 180° 0 0.2 0.5 0.2 1 4 GHz 2 5 0° 0 −5 −0.2 −135° 10 −2 −0.5 −45° −1 1.0 −90° 001aab257 IS = 15.9 mA; VS = 5 V; PD = −35 dBm; Zo = 50 Ω. Fig 6. Input reflection coefficient (s11); typical values. 90° 1.0 +1 135° +0.5 0.8 45° +2 0.6 100 MHz +0.2 0.4 +5 0.2 180° 0 0.2 0.5 4 GHz 1 2 5 0° 0 −5 −0.2 −135° 10 −2 −0.5 −45° −1 −90° 1.0 001aab258 IS = 15.9 mA; VS = 5 V; PD = −35 dBm; Zo = 50 Ω. Fig 7. Output reflection coefficient (s22); typical values. 9397 750 13292 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 02 — 24 September 2004 7 of 14 BGA2716 Philips Semiconductors MMIC wideband amplifier 001aab259 0 001aab260 30 |s21| 2 (dB) |s12 | 2 (dB) (2) −20 20 (1) (3) −40 10 −60 0 0 1000 2000 3000 0 4000 1000 2000 3000 4000 f (MHz) f (MHz) IS = 15.9 mA; VS = 5 V; PD = −35 dBm; Zo = 50 Ω. PD = −35 dBm; Zo = 50 Ω. (1) IS = 19.5 mA; VS = 5.5 V. (2) IS = 15.9 mA; VS = 5 V. (3) IS = 12.4 mA; VS = 4.5 V. (s122) Fig 8. Isolation typical values. as a function of frequency; 001aab261 20 PL (dBm) 10 0 0 −10 −10 −20 −40 −30 −20 −10 001aab262 20 PL (dBm) (1) (2) (3) 10 Fig 9. Insertion gain (s212) as a function of frequency; typical values. 0 −20 −40 (1) (2) (3) −30 −20 PD (dBm) f = 1 GHz; Zo = 50 Ω. 0 PD (dBm) f = 2.2 GHz; Zo = 50 Ω. (1) VS = 5.5 V. (1) VS = 5.5 V. (2) VS = 5 V. (2) VS = 5 V. (3) VS = 4.5 V. (3) VS = 4.5 V. Fig 10. Load power as a function of drive power at 1 GHz; typical values. Fig 11. Load power as a function of drive power at 2.2 GHz; typical values. 9397 750 13292 Product data sheet −10 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 02 — 24 September 2004 8 of 14 BGA2716 Philips Semiconductors MMIC wideband amplifier 001aab263 8 001aab264 5 K NF (dB) 4 7 3 6 (1) 2 (2) (3) 5 1 4 0 0 500 1000 1500 2000 2500 f (MHz) Zo = 50 Ω. 0 1000 2000 3000 4000 f (MHz) IS = 15.9 mA; VS = 5 V; Zo = 50 Ω. (1) IS = 19.5 mA; VS = 5.5 V. (2) IS = 15.9 mA; VS = 5 V. (3) IS = 12.4 mA; VS = 4.5 V. Fig 12. Noise figure as a function of frequency; typical values. Fig 13. Stability factor as a function of frequency; typical values. 9397 750 13292 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 02 — 24 September 2004 9 of 14 BGA2716 Philips Semiconductors MMIC wideband amplifier Table 8: Scattering parameters VS = 5 V; IS = 15.9 mA; PD = −35 dBm; Zo = 50 Ω; Tamb = 25 °C. f (MHz) s11 s21 s12 s22 Magnitude Angle (ratio) (deg) Magnitude Angle (ratio) (deg) Magnitude Angle (ratio) (deg) Magnitude Angle (ratio) (deg) 100 0.182562 102.7794 12.69581 13.48682 0.029472 28.74955 0.39239 91.48628 1.3 200 0.123465 87.55274 13.13419 −5.272917 0.035438 −2.202361 0.267851 62.37296 1.2 400 0.107855 58.58513 13.47149 −31.7377 0.035299 −22.54301 0.227252 24.6455 1.2 600 0.114731 40.14071 13.57901 −53.09631 0.033167 −43.06353 0.227993 −3.493572 1.3 800 0.130176 24.28555 13.67457 −73.60665 0.033194 −59.63503 0.234967 −31.11084 1.3 1000 0.144984 9.657616 13.91705 −94.01973 0.029047 −76.09972 0.239818 −60.54722 1.4 1200 0.160922 −7.518892 14.10949 −114.55 0.028188 −88.34045 0.242141 −91.56898 1.4 1400 0.179351 −23.35989 14.2808 −135.3117 0.025188 −101.2729 0.243087 −124.5484 1.4 1600 0.20199 −41.01349 14.3825 −156.7041 0.022257 −110.3342 0.24499 −158.6224 1.5 1800 0.218268 −60.71294 14.26935 −178.3843 0.019611 −121.0192 0.255598 167.5983 1.7 2000 0.233965 −81.48254 14.0667 160.1504 0.018087 −127.6765 0.269829 136.117 1.8 2200 0.242904 −103.1109 13.83968 138.2379 0.017203 −137.8213 0.283613 106.0987 1.9 2400 0.246576 −125.52 13.46447 115.7594 0.016318 −138.8717 0.29058 77.95189 2.0 2600 0.249069 −148.8707 12.74638 93.38644 0.015514 −147.6622 0.281505 50.68612 2.2 2800 0.243665 −172.646 11.87558 71.02792 0.014954 −152.1988 0.25135 24.40624 2.5 3000 0.233266 163.9035 10.94049 50.42722 0.015522 −163.8718 0.211425 −0.674037 2.7 3200 0.222055 140.7754 10.05626 30.75908 0.016261 −170.5637 0.165534 −23.9944 2.9 3400 0.207486 117.0531 9.576357 11.98315 0.016664 −176.5407 0.118726 −46.28101 3.0 3600 0.191654 94.64431 9.199166 −7.677643 0.016982 176.9385 0.083354 −72.36691 3.2 3800 0.175783 71.9551 8.912598 −27.73098 0.017094 165.8227 0.058549 −109.9804 3.3 4000 0.163768 49.89436 8.618058 −48.90874 0.017414 157.6095 0.055225 −163.7132 3.3 9397 750 13292 Product data sheet K-factor © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 02 — 24 September 2004 10 of 14 BGA2716 Philips Semiconductors MMIC wideband amplifier 9. Package outline Plastic surface mounted package; 6 leads SOT363 D E B y X A HE 6 5 v M A 4 Q pin 1 index A A1 1 2 e1 3 bp c Lp w M B e detail X 0 1 2 mm scale DIMENSIONS (mm are the original dimensions) UNIT A A1 max bp c D E e e1 HE Lp Q v w y mm 1.1 0.8 0.1 0.30 0.20 0.25 0.10 2.2 1.8 1.35 1.15 1.3 0.65 2.2 2.0 0.45 0.15 0.25 0.15 0.2 0.2 0.1 OUTLINE VERSION REFERENCES IEC JEDEC SOT363 EIAJ SC-88 EUROPEAN PROJECTION ISSUE DATE 97-02-28 Fig 14. Package outline; SOT363 (SC-88). 9397 750 13292 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 02 — 24 September 2004 11 of 14 BGA2716 Philips Semiconductors MMIC wideband amplifier 10. Revision history Table 9: Revision history Document ID Release date Data sheet status Change notice Doc. number Supersedes BGA2716_2 20040924 Product data sheet - 9397 750 13292 BGA2716_N_1 Modifications: BGA2716_N_1 • The format of this data sheet has been redesigned to comply with the new presentation and information standard of Philips Semiconductors 20040202 Preliminary data sheet - 9397 750 13292 Product data sheet 9397 750 12827 - © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 02 — 24 September 2004 12 of 14 BGA2716 Philips Semiconductors MMIC wideband amplifier 11. Data sheet status Level Data sheet status [1] Product status [2] [3] Definition I Objective data Development This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. II Preliminary data Qualification This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. III Product data Production This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). [1] Please consult the most recently issued data sheet before initiating or completing a design. [2] The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. [3] For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status. 12. Definitions 13. Disclaimers Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Life support — These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Right to make changes — Philips Semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. When the product is in full production (status ‘Production’), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. 14. Contact information For additional information, please visit: http://www.semiconductors.philips.com For sales office addresses, send an email to: [email protected] 9397 750 13292 Product data sheet © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Rev. 02 — 24 September 2004 13 of 14 BGA2716 Philips Semiconductors MMIC wideband amplifier 15. Contents 1 1.1 1.2 1.3 1.4 2 3 4 5 6 7 8 8.1 9 10 11 12 13 14 Product profile . . . . . . . . . . . . . . . . . . . . . . . . . . 1 General description. . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Quick reference data. . . . . . . . . . . . . . . . . . . . . 1 Pinning information . . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 2 Thermal characteristics. . . . . . . . . . . . . . . . . . . 3 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Application information. . . . . . . . . . . . . . . . . . . 4 Application examples . . . . . . . . . . . . . . . . . . . . 5 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 11 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 12 Data sheet status . . . . . . . . . . . . . . . . . . . . . . . 13 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Contact information . . . . . . . . . . . . . . . . . . . . 13 © Koninklijke Philips Electronics N.V. 2004 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Date of release: 24 September 2004 Document number: 9397 750 13292 Published in The Netherlands