CA3083 ® Data Sheet February 7, 2006 General Purpose High Current NPN Transistor Array FN481.6 Features The CA3083 is a versatile array of five high current (to 100mA) NPN transistors on a common monolithic substrate. In addition, two of these transistors (Q1 and Q2) are matched at low current (i.e., 1mA) for applications in which offset parameters are of special importance. • High IC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100mA (Max) • Low VCE sat (at 50mA). . . . . . . . . . . . . . . . . . . 0.7V (Max) • Matched Pair (Q1 and Q2) - VIO (VBE Match) . . . . . . . . . . . . . . . . . . . . . ±5mV (Max) - IIO (at 1mA) . . . . . . . . . . . . . . . . . . . . . . . . 2.5µA (Max) Independent connections for each transistor plus a separate terminal for the substrate permit maximum flexibility in circuit design. • 5 Independent Transistors Plus Separate Substrate Connection Ordering Information Applications PART NUMBER TEMP. RANGE PART (°C) MARKING PACKAGE • Pb-Free Plus Anneal Available (RoHS Compliant) PKG. DWG. # • Signal Processing and Switching Systems Operating from DC to VHF E16.3 • Lamp and Relay Driver CA3083 CA3083 -55 to 125 16 Ld PDIP CA3083Z (Note) CA3083Z -55 to 125 16 Ld PDIP* (Pb-free) E16.3 CA3083M96 3083 -55 to 125 16 Ld SOIC Tape and Reel CA3083MZ (Note) 3083MZ -55 to 125 16 Ld SOIC (Pb-Free) M16.15 CA3083MZ96 3083MZ (Note) -55 to 125 16 Ld SOIC (Pb-Free) M16.15 Tape and Reel M16.15 • Differential Amplifier • Temperature Compensated Amplifier • Thyristor Firing *Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications. • See Application Note AN5296 “Applications of the CA3018 Circuit Transistor Array” for Suggested Applications Pinout CA3083 (PDIP, SOIC) TOP VIEW NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 16 1 2 3 15 Q1 14 Q2 13 4 SUBSTRATE Q5 5 12 11 6 Q3 7 8 1 Q4 10 9 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 1998, 2005, 2006. All Rights Reserved All other trademarks mentioned are the property of their respective owners. CA3083 Absolute Maximum Ratings Thermal Information The following ratings apply for each transistor in the device: Collector-to-Emitter Voltage, VCEO . . . . . . . . . . . . . . . . . . . . . . 15V Collector-to-Base Voltage, VCBO. . . . . . . . . . . . . . . . . . . . . . . . 20V Collector-to-Substrate Voltage, VCIO (Note 1). . . . . . . . . . . . . . 20V Emitter-to-Base Voltage, VEBO . . . . . . . . . . . . . . . . . . . . . . . . . . 5V Collector Current (IC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100mA Base Current (IB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20mA Thermal Resistance (Typical, Note 2) θJA (°C/W) θJC (°C/W) PDIP Package . . . . . . . . . . . . . . . . . . . 135 N/A SOIC Package . . . . . . . . . . . . . . . . . . . 200 N/A Maximum Power Dissipation (Any One Transistor) . . . . . . . 500mW Maximum Junction Temperature (Plastic Package) . . . . . . . 150°C Maximum Storage Temperature Range . . . . . . . . . -65°C to 150°C Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C (SOIC - Lead Tips Only) Operating Conditions Temperature Range. . . . . . . . . . . . . . . . . . . . . . . . . .-55°C to 125°C CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. The collector of each transistor of the CA3083 is isolated from the substrate by an integral diode. The substrate must be connected to a voltage which is more negative than any collector voltage in order to maintain isolation between transistors and provide normal transistor action. To avoid undesired coupling between transistors, the substrate Terminal (5) should be maintained at either DC or signal (AC) ground. A suitable bypass capacitor can be used to establish a signal ground. 2. θJA is measured with the component mounted on an evaluation PC board in free air. Electrical Specifications For Equipment Design, TA = 25°C PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS FOR EACH TRANSISTOR Collector-to-Base Breakdown Voltage V(BR)CBO IC = 100µA, IE = 0 20 60 - V Collector-to-Emitter Breakdown Voltage V(BR)CEO IC = 1mA, IB = 0 15 24 - V Collector-to-Substrate Breakdown Voltage V(BR)CIO ICI = 100µA, IB = 0, IE = 0 20 60 - V Emitter-to-Base Breakdown Voltage V(BR)EBO IE = 500µA, IC = 0 5 6.9 - V Collector-Cutoff-Current ICEO VCE = 10V, IB = 0 - - 10 µA Collector-Cutoff-Current ICBO VCB = 10V, IE = 0 - - 1 µA DC Forward-Current Transfer Ratio (Note 3) (Figure 1) hFE VCE = 3V IC = 10mA 40 76 - IC = 50mA 40 75 - Base-to-Emitter Voltage (Figure 2) VBE VCE = 3V, IC = 10mA 0.65 0.74 0.85 V VCE SAT IC = 50mA, IB = 5mA - 0.40 0.70 V fT VCE = 3V, IC = 10mA - 450 - MHz Absolute Input Offset Voltage (Figure 6) |VIO| VCE = 3V, IC = 1mA - 1.2 5 mV Absolute Input Offset Current (Figure 7) |IIO| VCE = 3V, IC = 1mA - 0.7 2.5 µA Collector-to-Emitter Saturation Voltage (Figures 3, 4) Gain Bandwidth Product FOR TRANSISTORS Q1 AND Q2 (As a Differential Amplifier) NOTE: 3. Actual forcing current is via the emitter for this test. 2 FN481.6 February 7, 2006 CA3083 100 0.9 VCE = 3V VCE = 3V 90 BASE-TO-EMITTER VOLTAGE (V) DC FORWARD CURRENT TRANSFER RATIO Typical Performance Curves TA = 70°C TA = 25°C 80 TA = 0°C 70 60 1 10 TA = 0°C TA = 25°C 0.7 TA = 70°C 0.6 0.5 0.1 50 0.1 0.8 100 COLLECTOR CURRENT (mA) FIGURE 1. hFE vs IC 1.2 hFE = 10, TA = 25oC 0.8 0.6 0.4 MAXIMUM 0.2 TYPICAL 1 10 0.8 0.6 0.4 0 100 FIGURE 3. VCE SAT vs IC ABSOLUTE INPUT OFFSET VOLTAGE (mV) BASE-TO-EMITTER SATURATION VOLTAGE (V) hFE = 10, TA = 25°C 0.9 0.8 0.7 0.6 0.5 3 TYPICAL 1 10 COLLECTOR CURRENT (mA) 100 FIGURE 4. VCE SAT vs IC 1 FIGURE 5. VBE SAT vs IC MAXIMUM 0.2 COLLECTOR CURRENT (mA) 10 COLLECTOR CURRENT (mA) hFE = 10, TA = 70°C 1 0 1 100 FIGURE 2. VBE vs IC COLLECTOR-TO-EMITTER SATURATION VOLTAGE (V) COLLECTOR-TO-EMITTER SATURATION VOLTAGE (V) 1 1 10 COLLECTOR CURRENT (mA) 100 6 VCE = 3V, TA = 25°C 5 4 3 2 1 0 0.1 1 COLLECTOR CURRENT (mA) 10 FIGURE 6. VIO vs IC (TRANSISTORS Q1 AND Q2 AS A DIFFERENTIAL AMPLIFIER) FN481.6 February 7, 2006 CA3083 ABSOLUTE INPUT OFFSET CURRENT (µA) Typical Performance Curves (Continued) 10 VCE = 3V, TA = 25°C 1 0.1 0.1 1 COLLECTOR CURRENT (mA) 10 FIGURE 7. IIO vs IC (TRANSISTORS Q1 AND Q2 AS A DIFFERENTIAL AMPLIFIER) All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 4 FN481.6 February 7, 2006