CYPRESS CY7C1480BV33

CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
72-Mbit (2M x 36/4M x 18/1M x 72)
Pipelined Sync SRAM
Features
Functional Description
■
Supports bus operation up to 250 MHz
■
Available speed grades are 250, 200, and 167 MHz
■
Registered inputs and outputs for pipelined operation
■
3.3V core power supply
■
2.5V/3.3V IO operation
■
Fast clock-to-output times
❐ 3.0 ns (for 250 MHz device)
■
Provide high performance 3-1-1-1 access rate
The CY7C1480BV33, CY7C1482BV33, and CY7C1486BV33
SRAM integrates 2M x 36/4M x 18/1M × 72 SRAM cells with
advanced synchronous peripheral circuitry and a 2-bit counter
for internal burst operation. All synchronous inputs are gated by
registers controlled by a positive-edge-triggered Clock Input
(CLK). The synchronous inputs include all addresses, all data
inputs, address-pipelining Chip Enable (CE1), depth-expansion
Chip Enables (CE2 and CE3), Burst Control inputs (ADSC,
ADSP, and ADV), Write Enables (BWX, and BWE), and Global
Write (GW). Asynchronous inputs include the Output Enable
(OE) and the ZZ pin.
■
User selectable burst counter supporting Intel®
Pentium® interleaved or linear burst sequences
■
Separate processor and controller address strobes
■
Synchronous self timed writes
■
Asynchronous output enable
■
Single cycle chip deselect
■
CY7C1480BV33, CY7C1482BV33 available in
JEDEC-standard Pb-free 100-pin TQFP, Pb-free and
non Pb-free 165-ball FBGA package. CY7C1486BV33
available in Pb-free and non-Pb-free 209-ball FBGA package
■
IEEE 1149.1 JTAG-Compatible Boundary Scan
■
“ZZ” Sleep Mode option
Addresses and chip enables are registered at the rising edge of
the clock when either Address Strobe Processor (ADSP) or
Address Strobe Controller (ADSC) are active. Subsequent burst
addresses may be internally generated as controlled by the
Advance pin (ADV).
Address, data inputs, and write controls are registered on-chip
to initiate a self timed write cycle.This part supports byte write
operations (see sections Pin Definitions on page 7 and Truth
Table on page 10 for further details). Write cycles can be one to
two or four bytes wide as controlled by the byte write control
inputs. GW when active LOW causes all bytes to be written.
The CY7C1480BV33, CY7C1482BV33, and CY7C1486BV33
operates from a +3.3V core power supply while all outputs may
operate with either a +2.5 or +3.3V supply. All inputs and outputs
are JEDEC standard JESD8-5 compatible. For best practices
recommendations, refer to the Cypress application note AN1064
“SRAM System Guidelines”.
Selection Guide
250 MHz
200 MHz
167 MHz
Unit
Maximum Access Time
Description
3.0
3.0
3.4
ns
Maximum Operating Current
500
500
450
mA
Maximum CMOS Standby Current
120
120
120
mA
Cypress Semiconductor Corporation
Document #: 001-15145 Rev. *A
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised March 05, 2008
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
Logic Block Diagram – CY7C1480BV33 (2M x 36)
A 0, A1, A
ADDRESS
REGISTER
2
A [1:0]
MODE
ADV
CLK
Q1
BURST
COUNTER
CLR AND
LOGIC
ADSC
Q0
ADSP
BW D
DQ D ,DQP D
BYTE
WRITE REGISTER
DQ D ,DQPD
BYTE
WRITE DRIVER
BW C
DQ C ,DQP C
BYTE
WRITE REGISTER
DQ C ,DQP C
BYTE
WRITE DRIVER
DQ B ,DQP B
BYTE
WRITE REGISTER
DQ B ,DQP B
BYTE
WRITE DRIVER
BW B
BW A
BWE
ZZ
SENSE
AMPS
OUTPUT
REGISTERS
OUTPUT
BUFFERS
E
DQs
DQP A
DQP B
DQP C
DQP D
DQ A ,DQP A
BYTE
WRITE DRIVER
DQ A ,DQP A
BYTE
WRITE REGISTER
GW
CE 1
CE 2
CE 3
OE
MEMORY
ARRAY
ENABLE
REGISTER
INPUT
REGISTERS
PIPELINED
ENABLE
SLEEP
CONTROL
Logic Block Diagram – CY7C1482BV33 (4M x 18)
A0, A1, A
ADDRESS
REGISTER
2
MODE
A[1:0]
BURST Q1
COUNTER AND
LOGIC
CLR
Q0
ADV
CLK
ADSC
ADSP
BW B
DQ B, DQP B
WRITE DRIVER
DQ B, DQP B
WRITE REGISTER
MEMORY
ARRAY
BW A
DQ A, DQP A
WRITE DRIVER
DQ A, DQP A
WRITE REGISTER
SENSE
AMPS
OUTPUT
REGISTERS
OUTPUT
BUFFERS
DQs
DQP A
DQP B
E
BWE
GW
CE 1
CE2
CE3
ENABLE
REGISTER
PIPELINED
ENABLE
INPUT
REGISTERS
OE
ZZ
SLEEP
CONTROL
Document #: 001-15145 Rev. *A
Page 2 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
Logic Block Diagram – CY7C1486BV33 (1M x 72)
ADDRESS
REGISTER
A 0, A1,A
A[1:0]
MODE
Q1
BINARY
COUNTER
CLR
Q0
ADV
CLK
ADSC
ADSP
BW H
DQ H , DQPH
WRITE DRIVER
DQ H , DQPH
WRITE DRIVER
BW G
DQ F, DQPF
WRITE DRIVER
DQ G , DQPG
WRITE DRIVER
BW F
DQ F, DQPF
WRITE DRIVER
DQ F, DQPF
WRITE DRIVER
BW E
DQ E , DQPE
WRITE DRIVER
DQ
E , DQP
BYTE
“a” E
WRITE DRIVER
BW D
DQ D , DQPD
WRITE DRIVER
DQ D , DQPD
WRITE DRIVER
BW C
DQ C, DQPC
WRITE DRIVER
DQ C, DQPC
WRITE DRIVER
MEMORY
ARRAY
SENSE
AMPS
BW B
BW A
BWE
GW
CE1
CE2
CE3
OE
ZZ
DQ B , DQPB
WRITE DRIVER
DQ B , DQPB
WRITE DRIVER
OUTPUT
BUFFERS
E
DQ A , DQPA
WRITE DRIVER
DQ A , DQPA
WRITE DRIVER
ENABLE
REGISTER
OUTPUT
REGISTERS
PIPELINED
ENABLE
INPUT
REGISTERS
DQs
DQP A
DQP B
DQP C
DQP D
DQP E
DQP F
DQP G
DQP H
SLEEP
CONTROL
Document #: 001-15145 Rev. *A
Page 3 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
Pin Configurations
Figure 2. CY7C1482BV33 100-Pin TQFP Pinout
NC
NC
NC
VDDQ
VSSQ
NC
NC
DQB
DQB
VSSQ
VDDQ
DQB
DQB
NC
VDD
NC
VSS
DQB
DQB
VDDQ
VSSQ
DQB
DQB
DQPB
NC
VSSQ
VDDQ
NC
NC
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
CY7C1482BV33
(4M x 18)
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
Document #: 001-15145 Rev. *A
A
NC
NC
VDDQ
VSSQ
NC
DQPA
DQA
DQA
VSSQ
VDDQ
DQA
DQA
VSS
NC
VDD
ZZ
DQA
DQA
VDDQ
VSSQ
DQA
DQA
NC
NC
VSSQ
VDDQ
NC
NC
NC
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
DQPB
DQB
DQB
VDDQ
VSSQ
DQB
DQB
DQB
DQB
VSSQ
VDDQ
DQB
DQB
VSS
NC
VDD
ZZ
DQA
DQA
VDDQ
VSSQ
DQA
DQA
DQA
DQA
VSSQ
VDDQ
DQA
DQA
DQPA
MODE
A
A
A
A
A1
A0
A
A
VSS
VDD
CY7C1480BV33
(2M x 36)
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
MODE
A
A
A
A
A1
A0
A
A
VSS
VDD
DQPC
DQC
DQc
VDDQ
VSSQ
DQC
DQC
DQC
DQC
VSSQ
VDDQ
DQC
DQC
NC
VDD
NC
VSS
DQD
DQD
VDDQ
VSSQ
DQD
DQD
DQD
DQD
VSSQ
VDDQ
DQD
DQD
DQPD
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
A
A
CE1
CE2
NC
NC
BWB
BWA
CE3
VDD
VSS
CLK
GW
BWE
OE
ADSC
ADSP
ADV
A
A
A
A
CE1
CE2
BWD
BWC
BWB
BWA
CE3
VDD
VSS
CLK
GW
BWE
OE
ADSC
ADSP
ADV
A
A
Figure 1. CY7C1480BV33 100-Pin TQFP Pinout
Page 4 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
Pin Configurations
(continued)
165-Ball FBGA (15 x 17 x 1.4 mm) Pinout
CY7C1480BV33 (2M x 36)
1
A
B
C
D
E
F
G
H
J
K
L
M
N
P
NC/288M
R
2
A
3
4
5
6
7
8
9
10
11
CE1
BWC
BWB
CE3
BWE
ADSC
ADV
A
NC
GW
VSS
ADSP
VDDQ
NC/144M
A
CE2
BWD
BWA
CLK
DQPC
DQC
NC
DQC
VDDQ
VSS
VDDQ
VSS
VDD
VSS
VSS
VSS
VSS
OE
VSS
VDD
A
NC/576M
VDDQ
NC/1G
DQB
DQPB
DQB
DQC
DQC
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQB
DQB
DQC
DQC
NC
DQD
DQC
VDDQ
VDD
VSS
VSS
VSS
VDD
DQB
DQB
VDD
VDD
VDD
VDDQ
VDDQ
NC
VDDQ
DQC
NC
DQD
VDDQ
NC
VDDQ
VDD
VDD
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
DQB
NC
DQA
DQB
ZZ
DQA
DQD
DQD
VDDQ
VDD
VSS
VSS
DQD
DQD
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQA
DQA
VSS
VDD
VDDQ
DQA
DQA
DQD
DQPD
DQD
NC
VDDQ
VDDQ
VDD
VSS
VSS
NC
VSS
A
VSS
NC
VDD
VSS
VDDQ
VDDQ
DQA
NC
DQA
DQPA
NC
A
A
A
TDI
A1
TDO
A
A
A
A
MODE
A
A
A
TMS
TCK
A
A
A
A
A0
CY7C1482BV33 (4M x 18)
1
2
A
B
C
D
E
F
G
H
J
K
L
M
N
P
NC/288M
A
NC/144M
A
NC
NC
R
4
5
CE1
CE2
BWB
NC
9
10
11
ADSC
OE
ADV
ADSP
A
CE3
NC
BWA
CLK
BWE
GW
A
NC
DQB
VDDQ
VDDQ
VSS
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDDQ
VDDQ
NC
DQB
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
NC
DQA
NC
NC
NC
DQB
DQB
VDDQ
VDD
DQB
NC
NC
VDDQ
NC
VDDQ
VDD
VDD
VDD
VSS
VSS
VSS
VDD
DQA
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VDD
VDDQ
VDDQ
NC
VDDQ
NC
VSS
VSS
VSS
NC
NC
DQA
DQA
ZZ
NC
DQB
NC
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQA
NC
DQB
NC
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQA
NC
DQB
DQPB
NC
NC
VDDQ
VDDQ
VDD
VSS
VSS
NC
VSS
A
VSS
NC
VDD
VSS
VDDQ
VDDQ
DQA
NC
NC
NC
NC
A
A
A
TDI
A1
TDO
A
A
A
A
MODE
A
A
A
TMS
A0
TCK
A
A
A
A
Document #: 001-15145 Rev. *A
3
6
7
8
A
NC/576M
NC/1G
DQPA
DQA
NC
Page 5 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
Pin Configurations
(continued)
209-Ball FBGA (14 x 22 x 1.76 mm) Pinout
CY7C1486BV33 (1M × 72)
1
2
3
4
5
6
7
8
9
10
11
A
DQG
DQG
A
CE2
ADSP
ADSC
ADV
CE3
A
DQB
DQB
B
DQG
DQG
BWSC
BWSG NC/288M
BWE
A
BWSB
BWSF
DQB
DQB
C
DQG
DQG
BWSH
BWSD NC/144M
CE1
NC/576M BWSE
BWSA
DQB
DQB
D
DQG
DQG
VSS
NC
NC/1G
OE
GW
NC
VSS
DQB
DQB
E
DQPG
DQPC
VDDQ
VDDQ
VDD
VDD
VDD
VDDQ
VDDQ
DQPF
DQPB
F
DQC
DQC
VSS
VSS
VSS
NC
VSS
VSS
VSS
DQF
DQF
G
DQC
DQC
VDDQ
VDDQ
VDD
NC
VDD
VDDQ
VDDQ
DQF
DQF
H
DQC
DQC
VSS
VSS
VSS
NC
VSS
VSS
VSS
DQF
DQF
J
DQC
DQC
VDDQ
VDDQ
VDD
NC
VDD
VDDQ
VDDQ
DQF
DQF
K
NC
NC
CLK
NC
VSS
VSS
VSS
NC
NC
NC
NC
L
DQH
DQH
VDDQ
VDDQ
VDD
NC
VDD
VDDQ
VDDQ
DQA
DQA
M
DQH
DQH
VSS
VSS
VSS
NC
VSS
VSS
VSS
DQA
DQA
N
DQH
DQH
VDDQ
VDDQ
VDD
NC
VDD
VDDQ
VDDQ
DQA
DQA
P
DQH
DQH
VSS
VSS
VSS
ZZ
VSS
VSS
VSS
DQA
DQA
R
DQPD
VDDQ
VDD
VDD
VDD
VDDQ
VDDQ
DQPA
T
DQD
DQD
VSS
NC
NC
MODE
NC
NC
VSS
DQE
DQE
U
DQD
DQD
A
A
A
A
A
A
A
DQE
DQE
V
DQD
DQD
A
A
A
A1
A
A
A
DQE
DQE
W
DQD
DQD
TMS
TDI
A
A0
A
TCK
DQE
DQE
DQPH VDDQ
Document #: 001-15145 Rev. *A
TDO
DQPE
Page 6 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
Pin Definitions
Pin Name
IO
Description
A0, A1, A
InputSynchronous
Address Inputs used to Select One of the Address Locations. Sampled at the
rising edge of the CLK if ADSP or ADSC is active LOW, and CE1, CE2, and CE3 are
sampled active. A1: A0 are fed to the 2-bit counter.
BWA,BWB,BWC,BWD,
BWE,BWF,BWG,BWH
InputSynchronous
Byte Write Select Inputs, Active LOW. Qualified with BWE to conduct byte writes to
the SRAM. Sampled on the rising edge of CLK.
GW
InputSynchronous
Global Write Enable Input, Active LOW. When asserted LOW on the rising edge of
CLK, a global write is conducted (all bytes are written, regardless of the values on
BWX and BWE).
BWE
InputSynchronous
Byte Write Enable Input, Active LOW. Sampled on the rising edge of CLK. This
signal must be asserted LOW to conduct a byte write.
CLK
InputClock
Clock Input. Used to capture all synchronous inputs to the device. Also used to
increment the burst counter when ADV is asserted LOW during a burst operation.
CE1
InputSynchronous
Chip Enable 1 Input, Active LOW. Sampled on the rising edge of CLK. Used in
conjunction with CE2 and CE3 to select or deselect the device. ADSP is ignored if CE1
is HIGH. CE1 is sampled only when a new external address is loaded.
CE2
InputSynchronous
Chip Enable 2 Input, Active HIGH. Sampled on the rising edge of CLK. Used in
conjunction with CE1 and CE3 to select or deselect the device. CE2 is sampled only
when a new external address is loaded.
CE3
InputSynchronous
Chip Enable 3 Input, Active LOW. Sampled on the rising edge of CLK. Used in
conjunction with CE1 and CE2 to select or deselect the device. CE3 is sampled only
when a new external address is loaded.
OE
InputAsynchronous
Output Enable, Asynchronous Input, Active LOW. Controls the direction of the IO
pins. When LOW, the IO pins behave as outputs. When deasserted HIGH, IO pins are
tri-stated, and act as input data pins. OE is masked during the first clock of a read
cycle when emerging from a deselected state.
ADV
InputSynchronous
Advance Input Signal, Sampled on the Rising Edge of CLK, Active LOW. When
asserted, it automatically increments the address in a burst cycle.
ADSP
InputSynchronous
Address Strobe from Processor, Sampled on the Rising Edge of CLK, Active
LOW. When asserted LOW, addresses presented to the device are captured in the
address registers. A1: A0 are also loaded into the burst counter. When ADSP and
ADSC are both asserted, only ADSP is recognized. ASDP is ignored when CE1 is
deasserted HIGH.
ADSC
InputSynchronous
Address Strobe from Controller, Sampled on the Rising Edge of CLK, Active
LOW. When asserted LOW, addresses presented to the device are captured in the
address registers. A1: A0 are also loaded into the burst counter. When ADSP and
ADSC are both asserted, only ADSP is recognized.
ZZ
InputAsynchronous
ZZ “Sleep” Input, Active HIGH. When asserted HIGH, places the device in a
non-time-critical “sleep” condition with data integrity preserved. For normal operation,
this pin must be LOW or left floating. ZZ pin has an internal pull down.
DQs, DQPs
IOSynchronous
Bidirectional Data IO Lines. As inputs, they feed into an on-chip data register that is
triggered by the rising edge of CLK. As outputs, they deliver the data contained in the
memory location specified by the addresses presented during the previous clock rise
of the read cycle. The direction of the pins is controlled by OE. When OE is asserted
LOW, the pins behave as outputs. When HIGH, DQs and DQPX are placed in a tri-state
condition.
VDD
Power Supply
Power Supply Inputs to the Core of the Device.
Ground
VSS
VSSQ
[1]
VDDQ
IO Ground
Ground for the Core of the Device.
Ground for the IO Circuitry.
IO Power Supply Power supply for the IO circuitry.
Note
1. Applicable for TQFP package. For BGA package VSS serves as ground for the core and the IO circuitry.
Document #: 001-15145 Rev. *A
Page 7 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
Pin Definitions
(continued)
Pin Name
IO
Description
Input Static
Selects Burst Order. When tied to GND selects linear burst sequence. When tied to
VDD or left floating selects interleaved burst sequence. This is a strap pin and must
remain static during device operation. Mode Pin has an internal pull up.
TDO
JTAG Serial
Output
Synchronous
Serial Data-Out to the JTAG Circuit. Delivers data on the negative edge of TCK. If
the JTAG feature is not used, this pin must be disconnected. This pin is not available
on TQFP packages.
TDI
JTAG Serial
Input
Synchronous
Serial Data-In to the JTAG Circuit. Sampled on the rising edge of TCK. If the JTAG
feature is not used, this pin can be disconnected or connected to VDD. This pin is not
available on TQFP packages.
TMS
JTAG Serial
Input
Synchronous
Serial Data-In to the JTAG Circuit. Sampled on the rising edge of TCK. If the JTAG
feature is not used, this pin can be disconnected or connected to VDD. This pin is not
available on TQFP packages.
TCK
JTAG Clock
Clock Input to the JTAG Circuitry. If the JTAG feature is not used, this pin must be
connected to VSS. This pin is not available on TQFP packages.
NC
-
No Connects. Not internally connected to the die. 144M, 288M, 576M, and 1G are
address expansion pins and are not internally connected to the die.
MODE
Functional Overview
All synchronous inputs pass through input registers controlled by
the rising edge of the clock. All data outputs pass through output
registers controlled by the rising edge of the clock. Maximum
access delay from the clock rise (tCO) is 3.0 ns (250 MHz device).
The CY7C1480BV33, CY7C1482BV33, and CY7C1486BV33
support secondary cache in systems using either a linear or interleaved burst sequence. The interleaved burst order supports
Pentium and i486™ processors. The linear burst sequence is
suited for processors that use a linear burst sequence. The burst
order is user selectable, and is determined by sampling the
MODE input. Accesses may be initiated with the Processor
Address Strobe (ADSP) or the Controller Address Strobe
(ADSC). Address advancement through the burst sequence is
controlled by the ADV input. A two-bit on-chip wraparound burst
counter captures the first address in a burst sequence and
automatically increments the address for the rest of the burst
access.
Byte Write operations are qualified with the Byte Write Enable
(BWE) and Byte Write Select (BWX) inputs. A Global Write
Enable (GW) overrides all byte write inputs and writes data to all
four bytes. All writes are simplified with on-chip synchronous
self-timed write circuitry.
Three synchronous Chip Selects (CE1, CE2, and CE3) and an
asynchronous Output Enable (OE) provide easy bank selection
and output tri-state control. ADSP is ignored if CE1 is HIGH.
Single Read Accesses
This access is initiated when the following conditions are
satisfied at clock rise: (1) ADSP or ADSC is asserted LOW,
(2) CE1, CE2, CE3 are all asserted active, and (3) the write
signals (GW, BWE) are all deasserted HIGH. ADSP is ignored if
CE1 is HIGH. The address presented to the address inputs (A)
is stored into the address advancement logic and the Address
Register while being presented to the memory array. The
corresponding data is allowed to propagate to the input of the
Output Registers. At the rising edge of the next clock the data is
Document #: 001-15145 Rev. *A
allowed to propagate through the output register and onto the
data bus within 3.0 ns (250 MHz device) if OE is active LOW. The
only exception occurs when the SRAM is emerging from a
deselected state to a selected state; its outputs are always
tri-stated during the first cycle of the access. After the first cycle
of the access, the outputs are controlled by the OE signal.
Consecutive single read cycles are supported. After the SRAM
is deselected at clock rise by the chip select and either ADSP or
ADSC signals, its output tri-states immediately.
Single Write Accesses Initiated by ADSP
This access is initiated when both of the following conditions are
satisfied at clock rise: (1) ADSP is asserted LOW, and (2) CE1,
CE2, CE3 are all asserted active. The address presented to A is
loaded into the address register and the address advancement
logic while being delivered to the memory array. The write signals
(GW, BWE, and BWX) and ADV inputs are ignored during this
first cycle.
ADSP triggered write accesses require two clock cycles to
complete. If GW is asserted LOW on the second clock rise, the
data presented to the DQs inputs is written into the corresponding address location in the memory array. If GW is HIGH,
then the write operation is controlled by BWE and BWX signals.
The CY7C1480BV33, CY7C1482BV33, and CY7C1486BV33
provide byte write capability that is described in the section The
read/write truth table for CY7C1480BV33 follows.[4] on page 11.
Asserting the Byte Write Enable input (BWE) with the selected
Byte Write (BWX) input, selectively writes to only the desired
bytes. Bytes not selected during a Byte Write operation remain
unaltered. A synchronous self-timed Write mechanism is
provided to simplify the Write operations.
Because the CY7C1480BV33, CY7C1482BV33, and
CY7C1486BV33 are a common IO device, the Output Enable
(OE) must be deasserted HIGH before presenting data to the
DQs inputs. Doing so tri-states the output drivers. As a safety
precaution, DQs are automatically tri-stated whenever a Write
cycle is detected, regardless of the state of OE.
Page 8 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
Single Write Accesses Initiated by ADSC
Sleep Mode
ADSC Write accesses are initiated when the following conditions
are satisfied: (1) ADSC is asserted LOW, (2) ADSP is deasserted
HIGH, (3) CE1, CE2, CE3 are all asserted active, and (4) the
appropriate combination of the Write inputs (GW, BWE, and
BWX) are asserted active to conduct a Write to the desired byte.
ADSC-triggered Write accesses require a single clock cycle to
complete. The address presented to A is loaded into the address
register and the address advancement logic when being
delivered to the memory array. The ADV input is ignored during
this cycle. If a global Write is conducted, the data presented to
the DQs is written into the corresponding address location in the
memory core. If a Byte Write is conducted, only the selected
bytes are written. Bytes not selected during a Byte Write
operation remain unaltered. A synchronous self-timed Write
mechanism is provided to simplify the Write operations.
The ZZ input pin is an asynchronous input. Asserting ZZ places
the SRAM in a power conservation “sleep” mode. Two clock
cycles are required to enter into or exit from this “sleep” mode.
When in this mode, data integrity is guaranteed. Accesses
pending when entering the “sleep” mode are not considered
valid, and the completion of the operation is not guaranteed. The
device must be deselected before entering the “sleep” mode.
CE1, CE2, CE3, ADSP, and ADSC must remain inactive for the
duration of tZZREC after the ZZ input returns LOW.
Because the CY7C1480BV33, CY7C1482BV33, and
CY7C1486BV33 are a common IO device, the Output Enable
(OE) must be deasserted HIGH before presenting data to the
DQs inputs. Doing so tri-states the output drivers. As a safety
precaution, DQs are automatically tri-stated whenever a Write
cycle is detected, regardless of the state of OE.
Interleaved Burst Address Table
(MODE = Floating or VDD)
First
Address
A1: A0
Second
Address
A1: A0
Third
Address
A1: A0
Fourth
Address
A1: A0
00
01
10
11
01
00
11
10
10
11
00
01
11
10
01
00
Burst Sequences
The CY7C1480BV33, CY7C1482BV33, and CY7C1486BV33
provide a 2-bit wraparound counter, fed by A1: A0, that
implements either an interleaved or linear burst sequence. The
interleaved burst sequence is designed specifically to support
Intel Pentium applications. The linear burst sequence is
designed to support processors that follow a linear burst
sequence. The burst sequence is user selectable through the
MODE input.
Asserting ADV LOW at clock rise automatically increments the
burst counter to the next address in the burst sequence. Both
Read and Write burst operations are supported.
Linear Burst Address Table
(MODE = GND)
First
Address
A1: A0
Second
Address
A1: A0
Third
Address
A1: A0
Fourth
Address
A1: A0
00
01
10
11
01
10
11
00
10
11
00
01
11
00
01
10
ZZ Mode Electrical Characteristics
Parameter
Description
Test Conditions
IDDZZ
Sleep mode standby current
tZZS
Device operation to ZZ
ZZ > VDD – 0.2V
tZZREC
ZZ recovery time
ZZ < 0.2V
tZZI
ZZ Active to Sleep current
This parameter is sampled
tRZZI
ZZ Inactive to exit Sleep current
This parameter is sampled
Document #: 001-15145 Rev. *A
Min
ZZ > VDD – 0.2V
Max
Unit
120
mA
2tCYC
ns
2tCYC
ns
2tCYC
0
ns
ns
Page 9 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
The truth table for CY7C1480BV33, CY7C1482BV33, and CY7C1486BV33 follows.[2, 3, 4, 5, 6
Truth Table
Operation
Add. Used
CE1
CE2
CE3
ZZ
ADSP
ADSC
ADV
Deselect Cycle, Power Down
None
H
X
X
L
Deselect Cycle, Power Down
None
L
L
X
L
Deselect Cycle, Power Down
None
L
X
H
Deselect Cycle, Power Down
None
L
L
X
WRITE OE CLK
X
L
X
X
X
L-H Tri-State
L
X
X
X
X
L-H Tri-State
L
L
X
X
X
X
L-H Tri-State
L
H
L
X
X
X
L-H Tri-State
L-H Tri-State
Deselect Cycle, Power Down
None
L
X
H
L
H
L
X
X
X
Sleep Mode, Power Down
None
X
X
X
H
X
X
X
X
X
DQ
X
Tri-State
Q
Read Cycle, Begin Burst
External
L
H
L
L
L
X
X
X
L
L-H
Read Cycle, Begin Burst
External
L
H
L
L
L
X
X
X
H
L-H Tri-State
Write Cycle, Begin Burst
External
L
H
L
L
H
L
X
L
X
L-H
D
Read Cycle, Begin Burst
External
L
H
L
L
H
L
X
H
L
L-H
Q
Read Cycle, Begin Burst
External
L
H
L
L
H
L
X
H
H
L-H Tri-State
Read Cycle, Continue Burst
Next
X
X
X
L
H
H
L
H
L
L-H
Read Cycle, Continue Burst
Next
X
X
X
L
H
H
L
H
H
L-H Tri-State
Read Cycle, Continue Burst
Next
H
X
X
L
X
H
L
H
L
L-H
Read Cycle, Continue Burst
Next
H
X
X
L
X
H
L
H
H
L-H Tri-State
Write Cycle, Continue Burst
Next
X
X
X
L
H
H
L
L
X
L-H
D
Write Cycle, Continue Burst
Next
H
X
X
L
X
H
L
L
X
L-H
D
Read Cycle, Suspend Burst
Current
X
X
X
L
H
H
H
H
L
L-H
Q
Read Cycle, Suspend Burst
Current
X
X
X
L
H
H
H
H
H
L-H Tri-State
Read Cycle, Suspend Burst
Current
H
X
X
L
X
H
H
H
L
L-H
Read Cycle, Suspend Burst
Current
H
X
X
L
X
H
H
H
H
L-H Tri-State
Write Cycle,Suspend Burst
Current
X
X
X
L
H
H
H
L
X
L-H
D
Write Cycle,Suspend Burst
Current
H
X
X
L
X
H
H
L
X
L-H
D
Q
Q
Q
Notes
2. X = Do Not Care, H = Logic HIGH, L = Logic LOW.
3. WRITE = L when any one or more Byte Write enable signals and BWE = L or GW = L. WRITE = H when all Byte write enable signals, BWE, GW = H.
4. The DQ pins are controlled by the current cycle and the OE signal. OE is asynchronous and is not sampled with the clock.
5. The SRAM always initiates a read cycle when ADSP is asserted, regardless of the state of GW, BWE, or BWX. Writes may occur only on subsequent clocks after the
ADSP or with the assertion of ADSC. As a result, OE must be driven HIGH before the start of the write cycle to allow the outputs to tri-state. OE is a do not care for
the remainder of the write cycle.
6. OE is asynchronous and is not sampled with the clock rise. It is masked internally during write cycles. During a read cycle all data bits are tri-state when OE is inactive
or when the device is deselected, and all data bits behave as outputs when OE is active (LOW).
Document #: 001-15145 Rev. *A
Page 10 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
The read/write truth table for CY7C1480BV33 follows.[4]
Truth Table for Read/Write
Function (CY7C1480BV33)
GW
BWE
BWD
BWC
BWB
BWA
Read
H
H
X
X
X
X
Read
H
L
H
H
H
H
Write Byte A – (DQA and DQPA)
H
L
H
H
H
L
Write Byte B – (DQB and DQPB)
Write Bytes B, A
H
L
H
H
L
H
H
L
H
H
L
L
Write Byte C – (DQC and DQPC)
H
L
H
L
H
H
Write Bytes C, A
H
L
H
L
H
L
Write Bytes C, B
H
L
H
L
L
H
Write Bytes C, B, A
H
L
H
L
L
L
Write Byte D – (DQD and DQPD)
H
L
L
H
H
H
Write Bytes D, A
H
L
L
H
H
L
Write Bytes D, B
H
L
L
H
L
H
Write Bytes D, B, A
H
L
L
H
L
L
Write Bytes D, C
H
L
L
L
H
H
Write Bytes D, C, A
H
L
L
L
H
L
Write Bytes D, C, B
H
L
L
L
L
H
Write All Bytes
H
L
L
L
L
L
Write All Bytes
L
X
X
X
X
X
GW
BWE
BWB
BWA
Read
H
H
X
X
Read
H
L
H
H
Write Byte A – (DQA and DQPA)
Write Byte B – (DQB and DQPB)
H
L
H
L
H
L
L
H
Write Bytes B, A
H
L
L
L
Write All Bytes
H
L
L
L
Write All Bytes
L
X
X
X
GW
BWE
BWX
H
H
X
The read/write truth table for CY7C1482BV33 follows.[4]
Truth Table for Read/Write
Function (CY7C1482BV33)
The read/write truth table for CY7C1482BV33 follows.[7]
Truth Table for Read/Write
Function (CY7C1486BV33)
Read
Read
H
L
All BW = H
Write Byte x – (DQx and DQPx)
H
L
L
Write All Bytes
H
L
All BW = L
Write All Bytes
L
X
X
Note
7. BWx represents any byte write signal BW[0..7].To enable any byte write BWx, a Logic LOW signal must be applied at clock rise. Any number of bye writes can be
enabled at the same time for any given write.
Document #: 001-15145 Rev. *A
Page 11 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
IEEE 1149.1 Serial Boundary Scan (JTAG)
The CY7C1480BV33, CY7C1482BV33, and CY7C1486BV33
incorporate a serial boundary scan test access port (TAP). This
port operates in accordance with IEEE Standard 1149.1-1990
but does not have the set of functions required for full 1149.1
compliance. These functions from the IEEE specification are
excluded because their inclusion places an added delay in the
critical speed path of the SRAM. Note that the TAP controller
functions in a manner that does not conflict with the operation of
other devices using 1149.1 fully compliant TAPs. The TAP
operates using JEDEC-standard 3.3V or 2.5V IO logic levels.
Performing a TAP Reset
Perform a RESET by forcing TMS HIGH (VDD) for five rising
edges of TCK. This RESET does not affect the operation of the
SRAM and may be performed while the SRAM is operating.
At power up, the TAP is reset internally to ensure that TDO
comes up in a High-Z state.
TAP Registers
The CY7C1480BV33, CY7C1482BV33, and CY7C1486BV33
contain a TAP controller, instruction register, boundary scan
register, bypass register, and ID register.
Registers are connected between the TDI and TDO balls and
enable data to be scanned into and out of the SRAM test circuitry.
Only one register can be selected at a time through the
instruction register. Data is serially loaded into the TDI ball on the
rising edge of TCK. Data is output on the TDO ball on the falling
edge of TCK.
Disabling the JTAG Feature
Instruction Register
It is possible to operate the SRAM without using the JTAG
feature. To disable the TAP controller, tie TCK LOW (VSS) to
prevent device clocking. TDI and TMS are internally pulled up
and may be unconnected. They may alternatively be connected
to VDD through a pull up resistor. TDO must be left unconnected.
At power up, the device comes up in a reset state, which does
not interfere with the operation of the device.
Three-bit instructions can be serially loaded into the instruction
register. This register is loaded when it is placed between the TDI
and TDO balls as shown in the TAP Controller Block Diagram on
page 15. At power up, the instruction register is loaded with the
IDCODE instruction. It is also loaded with the IDCODE
instruction if the controller is placed in a reset state, as described
in the previous section.
The 0/1 next to each state represents the value of TMS at the
rising edge of TCK.
When the TAP controller is in the Capture-IR state, the two least
significant bits are loaded with a binary “01” pattern to enable
fault isolation of the board-level serial test data path.
Test Access Port (TAP)
Test Clock (TCK)
The test clock is used only with the TAP controller. All inputs are
captured on the rising edge of TCK. All outputs are driven from
the falling edge of TCK.
Test Mode Select (TMS)
The TMS input gives commands to the TAP controller and is
sampled on the rising edge of TCK. Leave this ball unconnected
if the TAP is not used. The ball is pulled up internally, resulting in
a logic HIGH level.
Test Data-In (TDI)
The TDI ball serially inputs information into the registers and can
be connected to the input of any of the registers. The register
between TDI and TDO is chosen by the instruction that is loaded
into the TAP instruction register. For information about loading
the instruction register, see the TAP Controller State Diagram on
page 14. TDI is internally pulled up and can be unconnected if
the TAP is unused in an application. TDI is connected to the most
significant bit (MSB) of any register. (See the TAP Controller
Block Diagram on page 15.)
Test Data-Out (TDO)
The TDO output ball serially clocks data-out from the registers.
The output is active depending upon the current state of the TAP
state machine. The output changes on the falling edge of TCK.
TDO is connected to the least significant bit (LSB) of any register.
(See the TAP Controller State Diagram on page 14.)
Document #: 001-15145 Rev. *A
Bypass Register
To save time when serially shifting data through registers, it is
sometimes advantageous to skip certain chips. The bypass
register is a single-bit register that can be placed between the
TDI and TDO balls. This enables data to be shifted through the
SRAM with minimal delay. The bypass register is set LOW (VSS)
when the BYPASS instruction is executed.
Boundary Scan Register
The boundary scan register is connected to all the input and
bidirectional balls on the SRAM. The x36 configuration has a
73-bit-long register, and the x18 configuration has a 54-bit-long
register.
The boundary scan register is loaded with the contents of the
RAM IO ring when the TAP controller is in the Capture-DR state
and is then placed between the TDI and TDO balls when the
controller is moved to the Shift-DR state. The EXTEST,
SAMPLE/PRELOAD, and SAMPLE Z instructions can be used
to capture the contents of the IO ring.
The Boundary Scan Order tables show the order in which the bits
are connected. Each bit corresponds to one of the bumps on the
SRAM package. The MSB of the register is connected to TDI and
the LSB is connected to TDO.
Identification (ID) Register
The ID register is loaded with a vendor-specific, 32-bit code
during the Capture-DR state when the IDCODE command is
loaded in the instruction register. The IDCODE is hardwired into
the SRAM and can be shifted out when the TAP controller is in
the Shift-DR state. The ID register has a vendor code and other
information described in the section Identification Register
Definitions on page 18.
Page 12 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
TAP Instruction Set
Overview
Eight different instructions are possible with the three-bit
instruction register. All combinations are listed in “Identification
Codes” on page 18. Three of these instructions are listed as
RESERVED and must not be used. The other five instructions
are described in detail in this section.
The TAP controller used in this SRAM is not fully compliant to the
1149.1 convention because some of the mandatory 1149.1
instructions are not fully implemented.
The TAP controller cannot be used to load address data or
control signals into the SRAM and cannot preload the IO buffers.
The SRAM does not implement the 1149.1 commands EXTEST
or INTEST or the PRELOAD portion of SAMPLE/PRELOAD;
rather, it performs a capture of the IO ring when these
instructions are executed.
Instructions are loaded into the TAP controller during the Shift-IR
state when the instruction register is placed between TDI and
TDO. During this state, instructions are shifted through the
instruction register through the TDI and TDO balls. To execute
the instruction after it is shifted in, the TAP controller must be
moved into the Update-IR state.
EXTEST
EXTEST is a mandatory 1149.1 instruction, which must be
executed whenever the instruction register is loaded with all
zeros. EXTEST is not implemented in this SRAM TAP controller,
and therefore this device is not compliant to 1149.1. The TAP
controller does recognize an all-zero instruction.
SAMPLE/PRELOAD
SAMPLE/PRELOAD is a 1149.1 mandatory instruction. The
PRELOAD portion of this instruction is not implemented, so the
device TAP controller is not fully 1149.1 compliant.
When the SAMPLE/PRELOAD instruction is loaded into the
instruction register and the TAP controller is in the Capture-DR
state, a snapshot of data on the inputs and bidirectional balls is
captured in the boundary scan register.
Be aware that the TAP controller clock can only operate at a
frequency up to 10 MHz, while the SRAM clock operates more
than an order of magnitude faster. Because there is a large
difference in the clock frequencies, it is possible that during the
Capture-DR state, an input or output may undergo a transition.
The TAP may then try to capture a signal when in transition
(metastable state). This does not harm the device, but there is
no guarantee as to the value that may be captured. Repeatable
results may not be possible.
To guarantee that the boundary scan register captures the
correct value of a signal, the SRAM signal must be stabilized
long enough to meet the TAP controller’s capture setup plus hold
time (tCS plus tCH).
The SRAM clock input might not be captured correctly if there is
no way in a design to stop (or slow) the clock during a
SAMPLE/PRELOAD instruction. If this is an issue, it is still
possible to capture all other signals and simply ignore the value
of the CLK captured in the boundary scan register.
After the data is captured, the data is shifted out by putting the
TAP into the Shift-DR state. This places the boundary scan
register between the TDI and TDO balls.
When an EXTEST instruction is loaded into the instruction
register, the SRAM responds as if a SAMPLE/PRELOAD
instruction has been loaded. There is one difference between the
two instructions. Unlike the SAMPLE/PRELOAD instruction,
EXTEST places the SRAM outputs in a High-Z state.
Note that because the PRELOAD part of the command is not
implemented, putting the TAP to the Update-DR state when
performing a SAMPLE/PRELOAD instruction has the same
effect as the Pause-DR command.
IDCODE
When the BYPASS instruction is loaded in the instruction register
and the TAP is placed in a Shift-DR state, the bypass register is
placed between the TDI and TDO balls. The advantage of the
BYPASS instruction is that it shortens the boundary scan path
when multiple devices are connected together on a board.
The IDCODE instruction causes a vendor-specific, 32-bit code
to be loaded into the instruction register. It also places the
instruction register between the TDI and TDO balls and enables
the IDCODE to be shifted out of the device when the TAP
controller enters the Shift-DR state.
The IDCODE instruction is loaded into the instruction register at
power up or whenever the TAP controller is in a test logic reset
state.
BYPASS
Reserved
These instructions are not implemented but are reserved for
future use. Do not use these instructions.
SAMPLE Z
The SAMPLE Z instruction causes the boundary scan register to
be connected between the TDI and TDO balls when the TAP
controller is in a Shift-DR state. It also places all SRAM outputs
into a High-Z state.
Document #: 001-15145 Rev. *A
Page 13 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
TAP Controller State Diagram
1
TEST-LOGIC
RESET
0
0
RUN-TEST/
IDLE
1
SELECT
DR-SCA N
1
SELECT
IR-SCAN
0
1
0
1
CAPTURE-DR
CAPTURE-IR
0
0
SHIFT-DR
0
SHIFT-IR
1
1
EXIT1-IR
0
0
PAUSE-IR
1
0
1
EXIT2-DR
0
EXIT2-IR
1
1
UPDATE-DR
Document #: 001-15145 Rev. *A
1
0
PAUSE-DR
1
0
1
EXIT1-DR
0
1
0
UPDATE-IR
1
0
Page 14 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
TAP Controller Block Diagram
0
Bypass Register
2 1 0
TDI
Selection
Circuitry
Instruction Register
Selection
Circuitry
TDO
31 30 29 . . . 2 1 0
Identification Register
x . . . . . 2 1 0
Boundary Scan Register
TCK
TM S
Document #: 001-15145 Rev. *A
TAP CONTROLLER
Page 15 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
3.3V TAP AC Test Conditions
2.5V TAP AC Test Conditions
Input pulse levels.................................................VSS to 3.3V
Input pulse levels................................................. VSS to 2.5V
Input rise and fall times....................................................1 ns
Input rise and fall time .....................................................1 ns
Input timing reference levels........................................... 1.5V
Input timing reference levels......................................... 1.25V
Output reference levels .................................................. 1.5V
Output reference levels ................................................ 1.25V
Test load termination supply voltage .............................. 1.5V
Test load termination supply voltage ............................ 1.25V
3.3V TAP AC Output Load Equivalent
2.5V TAP AC Output Load Equivalent
1.5V
1.25V
50Ω
50Ω
TDO
TDO
Z O= 50Ω
20pF
Z O= 50Ω
20pF
TAP DC Electrical Characteristics And Operating Conditions
(0°C < TA < +70°C; VDD = 3.135 to 3.6V unless otherwise noted)[8]
Parameter
Description
Test Conditions
IOH = –4.0 mA, VDDQ = 3.3V
Min
Max
Unit
VOH1
Output HIGH Voltage
2.4
IOH = –1.0 mA, VDDQ = 2.5V
2.0
V
VOH2
Output HIGH Voltage
IOH = –100 µA
VDDQ = 3.3V
2.9
V
VDDQ = 2.5V
2.1
VOL1
Output LOW Voltage
IOL = 8.0 mA
VDDQ = 3.3V
0.4
V
IOL = 1.0 mA
VDDQ = 2.5V
0.4
V
VOL2
Output LOW Voltage
IOL = 100 µA
VDDQ = 3.3V
0.2
V
VIH
Input HIGH Voltage
VDDQ = 3.3V
VIL
Input LOW Voltage
VDDQ = 2.5V
IX
Input Load Current
VDDQ = 2.5V
GND < VIN < VDDQ
V
V
0.2
V
2.0
VDD + 0.3
V
VDDQ = 2.5V
1.7
VDD + 0.3
V
VDDQ = 3.3V
–0.3
0.8
V
–0.3
0.7
V
–5
5
µA
Note
8. All voltages referenced to VSS (GND).
Document #: 001-15145 Rev. *A
Page 16 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
TAP AC Switching Characteristics
Over the Operating Range[9, 10]
Parameter
Description
Min
Max
Unit
20
MHz
Clock
tTCYC
TCK Clock Cycle Time
tTF
TCK Clock Frequency
tTH
TCK Clock HIGH Time
20
ns
tTL
TCK Clock LOW Time
20
ns
50
ns
Output Times
tTDOV
TCK Clock LOW to TDO Valid
tTDOX
TCK Clock LOW to TDO Invalid
0
ns
tTMSS
TMS Setup to TCK Clock Rise
5
ns
tTDIS
TDI Setup to TCK Clock Rise
5
ns
tCS
Capture Setup to TCK Rise
5
ns
10
ns
Setup Times
Hold Times
tTMSH
TMS Hold after TCK Clock Rise
5
ns
tTDIH
TDI Hold after Clock Rise
5
ns
tCH
Capture Hold after Clock Rise
5
ns
TAP Timing
Figure 3. TAP Timing
1
2
Test Clock
(TCK )
3
t TH
t TM SS
t TM SH
t TDIS
t TDIH
t
TL
4
5
6
t CY C
Test M ode Select
(TM S)
Test Data-In
(TDI)
t TDOV
t TDOX
Test Data-Out
(TDO)
DON’T CA RE
UNDEFINED
Notes
9. tCS and tCH refer to the setup and hold time requirements of latching data from the boundary scan register.
10. Test conditions are specified using the load in TAP AC Test Conditions. tR/tF = 1 ns.
Document #: 001-15145 Rev. *A
Page 17 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
Identification Register Definitions
Instruction Field
Revision Number (31:29)
Device Depth (28:24)
Architecture/Memory Type(23:18)
Bus Width/Density(17:12)
Cypress JEDEC ID Code (11:1)
ID Register Presence Indicator (0)
CY7C1480BV33
(2M x36)
CY7C1482BV33
(4M x 18)
CY7C1486BV33
(1M x72)
000
000
000
01011
01011
01011
000000
000000
000000
Description
Describes the version number
Reserved for internal use
Defines memory type and architecture
100100
010100
110100
00000110100
00000110100
00000110100
Enables unique identification of SRAM
vendor
Defines width and density
1
1
1
Indicates the presence of an ID register
Scan Register Sizes
Register Name
Instruction
Bit Size (x36)
Bit Size (x18)
Bit Size (x72)
3
3
3
Bypass
1
1
1
ID
32
32
32
Boundary Scan Order – 165FBGA
73
54
-
-
-
112
Boundary Scan Order – 209BGA
Identification Codes
Instruction
Code
Description
EXTEST
000
Captures the IO ring contents.
IDCODE
001
Loads the ID register with the vendor ID code and places the register between
TDI and TDO. This operation does not affect SRAM operations.
SAMPLE Z
010
Captures IO ring contents. Places the boundary scan register between TDI and
TDO.
Forces all SRAM output drivers to a High-Z state.
RESERVED
011
Do Not Use: This instruction is reserved for future use.
SAMPLE/PRELOAD
100
Captures IO ring contents. Places the boundary scan register between TDI and
TDO.
Does not affect SRAM operation.
RESERVED
101
Do Not Use: This instruction is reserved for future use.
RESERVED
110
Do Not Use: This instruction is reserved for future use.
BYPASS
111
Places the bypass register between TDI and TDO. This operation does not
affect SRAM operations.
Document #: 001-15145 Rev. *A
Page 18 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
Boundary Scan Exit Order (2M x 36)
Bit #
165-Ball ID
Bit #
165-Ball ID
Bit #
165-Ball ID
Bit #
165-Ball ID
1
C1
21
R3
41
L10
61
B8
2
D1
22
P2
42
K11
62
A7
3
E1
23
R4
43
J11
63
B7
4
D2
24
P6
44
K10
64
B6
5
E2
25
R6
45
J10
65
A6
6
F1
26
N6
46
H11
66
B5
7
G1
27
P11
47
G11
67
A5
8
F2
28
R8
48
F11
68
A4
9
G2
29
P3
49
E11
69
B4
10
J1
30
P4
50
D10
70
B3
11
K1
31
P8
51
D11
71
A3
12
L1
32
P9
52
C11
72
A2
13
J2
33
P10
53
G10
73
B2
14
M1
34
R9
54
F10
15
N1
35
R10
55
E10
16
K2
36
R11
56
A10
17
L2
37
N11
57
B10
18
M2
38
M11
58
A9
19
R1
39
L11
59
B9
20
R2
40
M10
60
A8
Boundary Scan Exit Order (4M x 18)
Bit #
165-Ball ID
Bit #
165-Ball ID
Bit #
165-Ball ID
1
D2
19
R8
37
C11
2
E2
20
P3
38
A11
3
F2
21
P4
39
A10
4
G2
22
P8
40
B10
5
J1
23
P9
41
A9
6
K1
24
P10
42
B9
7
L1
25
R9
43
A8
8
M1
26
R10
44
B8
9
N1
27
R11
45
A7
10
R1
28
M10
46
B7
11
R2
29
L10
47
B6
12
R3
30
K10
48
A6
13
P2
31
J10
49
B5
14
R4
32
H11
50
A4
15
P6
33
G11
51
B3
16
R6
34
F11
52
A3
17
N6
35
E11
53
A2
18
P11
36
D11
54
B2
Document #: 001-15145 Rev. *A
Page 19 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
Boundary Scan Exit Order (1M x 72)
Bit #
209-Ball ID
Bit #
209-Ball ID
Bit #
209-Ball ID
Bit #
209-Ball ID
1
A1
29
T1
57
V10
85
C11
2
A2
30
T2
58
U11
86
C10
3
B1
31
U1
59
U10
87
B11
4
B2
32
U2
60
T11
88
B10
5
C1
33
V1
61
T10
89
A11
6
C2
34
V2
62
R11
90
A10
7
D1
35
W1
63
R10
91
A9
8
D2
36
W2
64
P11
92
U8
9
E1
37
T6
65
P10
93
A7
10
E2
38
V3
66
N11
94
A5
11
F1
39
V4
67
N10
95
A6
12
F2
40
U4
68
M11
96
D6
13
G1
41
W5
69
M10
97
B6
14
G2
42
V6
70
L11
98
D7
15
H1
43
W6
71
L10
99
K3
16
H2
44
U3
72
P6
100
A8
17
J1
45
U9
73
J11
101
B4
18
J2
46
V5
74
J10
102
B3
19
L1
47
U5
75
H11
103
C3
20
L2
48
U6
76
H10
104
C4
21
M1
49
W7
77
G11
105
C8
22
M2
50
V7
78
G10
106
C9
23
N1
51
U7
79
F11
107
B9
24
N2
52
V8
80
F10
108
B8
25
P1
53
V9
81
E10
109
A4
26
P2
54
W11
82
E11
110
C6
27
R2
55
W10
83
D11
111
B7
28
R1
56
V11
84
D10
112
A3
Document #: 001-15145 Rev. *A
Page 20 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
Maximum Ratings
DC Input Voltage ................................... –0.5V to VDD + 0.5V
Exceeding the maximum ratings may impair the useful life of the
device. These user guidelines are not tested.
Storage Temperature ................................. –65°C to +150°C
Ambient Temperature with
Power Applied ............................................ –55°C to +125°C
Current into Outputs (LOW)......................................... 20 mA
Static Discharge Voltage........................................... >2001V
(MIL-STD-883, Method 3015)
Latch up Current..................................................... >200 mA
Operating Range
Supply Voltage on VDD Relative to GND ........–0.3V to +4.6V
DC Voltage Applied to Outputs
in Tri-State ...........................................–0.5V to VDDQ + 0.5V
Ambient
VDD
VDDQ
Temperature
0°C to +70°C
3.3V –5%/+10% 2.5V – 5%
to VDD
–40°C to +85°C
Range
Supply Voltage on VDDQ Relative to GND ...... –0.3V to +VDD
Commercial
Industrial
Electrical Characteristics
Over the Operating Range[11, 12]
Parameter
Description
VDD
Power Supply Voltage
VDDQ
IO Supply Voltage
VOH
VOL
Output HIGH Voltage
Output LOW Voltage
Test Conditions
Min
Max
Unit
3.135
3.6
V
For 3.3V IO
3.135
VDD
V
For 2.5V IO
2.375
2.625
V
For 3.3V IO, IOH = –4.0 mA
2.4
V
For 2.5V IO, IOH = –1.0 mA
2.0
V
For 3.3V IO, IOL = 8.0 mA
0.4
For 2.5V IO, IOL = 1.0 mA
0.4
V
V
2.0
VDD + 0.3V
V
VIH
Input HIGH Voltage[11]
For 2.5V IO
1.7
VDD + 0.3V
V
VIL
Input LOW Voltage[11]
For 3.3V IO
–0.3
0.8
V
For 2.5V IO
–0.3
0.7
V
IX
Input Leakage Current
except ZZ and MODE
GND ≤ VI ≤ VDDQ
–5
5
μA
Input Current of MODE
Input = VSS
–30
For 3.3V IO
Input = VDD
Input Current of ZZ
Input = VSS
IOZ
Output Leakage Current
GND ≤ VI ≤ VDDQ, Output Disabled
IDD [13]
VDD Operating Supply
Current
VDD = Max., IOUT = 0 mA,
f = fMAX = 1/tCYC
5
Automatic CE
Power Down
Current—TTL Inputs
VDD = Max, Device Deselected,
VIN ≥ VIH or VIN ≤ VIL
f = fMAX = 1/tCYC
μA
μA
–5
Input = VDD
ISB1
μA
30
μA
5
μA
4.0 ns cycle, 250 MHz
500
mA
5.0 ns cycle, 200 MHz
500
mA
6.0 ns cycle, 167 MHz
450
mA
4.0 ns cycle, 250 MHz
245
mA
5.0 ns cycle, 200 MHz
245
mA
6.0 ns cycle, 167 MHz
245
mA
–5
Notes
11. Overshoot: VIH(AC) < VDD +1.5V (Pulse width less than tCYC/2). Undershoot: VIL(AC) > –2V (Pulse width less than tCYC/2).
12. Power up: Assumes a linear ramp from 0V to VDD(min.) within 200 ms. During this time VIH < VDD and VDDQ < VDD.
13. The operation current is calculated with 50% read cycle and 50% write cycle.
Document #: 001-15145 Rev. *A
Page 21 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
Electrical Characteristics
Over the Operating Range[11, 12] (continued)
Max
Unit
ISB2
Parameter
Automatic CE
Power Down
Current—CMOS Inputs
VDD = Max, Device Deselected,
All speeds
VIN ≤ 0.3V or VIN > VDDQ – 0.3V, f = 0
120
mA
ISB3
Automatic CE
Power Down
Current—CMOS Inputs
VDD = Max, Device Deselected, or
VIN ≤ 0.3V or VIN > VDDQ – 0.3V
f = fMAX = 1/tCYC
4.0 ns cycle, 250 MHz
245
mA
5.0 ns cycle, 200 MHz
245
mA
6.0 ns cycle, 167 MHz
245
mA
Automatic CE
Power Down
Current—TTL Inputs
VDD = Max, Device Deselected,
VIN ≥ VIH or VIN ≤ VIL, f = 0
All speeds
135
mA
ISB4
Description
Test Conditions
Min
Capacitance
Tested initially and after any design or process change that may affect these parameters.
Parameter
Description
CADDRESS
Address Input Capacitance
CDATA
Data Input Capacitance
Test Conditions
100 TQFP
Max
165 FBGA
Max
209 FBGA
Max
TA = 25°C, f = 1 MHz,
VDD = 3.3V
VDDQ = 2.5V
6
6
6
pF
5
5
5
pF
Unit
CCTRL
Control Input Capacitance
8
8
8
pF
CCLK
Clock Input Capacitance
6
6
6
pF
CIO
Input/Output Capacitance
5
5
5
pF
Thermal Resistance
Tested initially and after any design or process change that may affect these parameters.
Parameter
Description
ΘJA
Thermal Resistance
(Junction to Ambient)
ΘJC
Thermal Resistance
(Junction to Case)
Document #: 001-15145 Rev. *A
Test Conditions
100 TQFP
Package
165 FBGA
Package
209 FBGA
Package
Unit
Test conditions follow standard test
methods and procedures for
measuring thermal impedance,
according to EIA/JESD51.
24.63
16.3
15.2
°C/W
2.28
2.1
1.7
°C/W
Page 22 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
Figure 4. AC Test Loads and Waveforms
3.3V IO Test Load
R = 317Ω
3.3V
OUTPUT
ALL INPUT PULSES
VDDQ
OUTPUT
RL = 50Ω
Z0 = 50Ω
10%
90%
10%
90%
GND
5 pF
R = 351Ω
≤ 1 ns
≤ 1 ns
VL = 1.5V
INCLUDING
JIG AND
SCOPE
(a)
(c)
(b)
2.5V IO Test Load
R = 1667Ω
2.5V
OUTPUT
10%
R = 1538Ω
VL = 1.25V
Document #: 001-15145 Rev. *A
INCLUDING
JIG AND
SCOPE
90%
10%
90%
GND
5 pF
(a)
ALL INPUT PULSES
VDDQ
OUTPUT
RL = 50Ω
Z0 = 50Ω
(b)
≤ 1 ns
≤ 1 ns
(c)
Page 23 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
Switching Characteristics
Over the Operating Range. Timing reference level is 1.5V when VDDQ = 3.3V and is 1.25V when VDDQ = 2.5V. Test conditions shown
in (a) of AC Test Loads and Waveforms on page 23 unless otherwise noted.
Parameter
tPOWER
Description
VDD(Typical) to the First Access[14]
250 MHz
Min
Max
200 MHz
Min
Max
167 MHz
Min
Max
Unit
1
1
1
ms
4.0
5.0
6.0
ns
Clock
tCYC
Clock Cycle Time
tCH
Clock HIGH
2.0
2.0
2.4
ns
tCL
Clock LOW
2.0
2.0
2.4
ns
Output Times
tCO
Data Output Valid After CLK Rise
tDOH
Data Output Hold After CLK Rise
1.3
1.3
1.5
ns
tCLZ
Clock to Low-Z[15, 16, 17]
1.3
1.3
1.5
ns
tCHZ
Clock to
High-Z[15, 16, 17]
3.0
3.0
3.4
ns
tOEV
OE LOW to Output Valid
3.0
3.0
3.4
ns
Low-Z[15, 16, 17]
tOELZ
OE LOW to Output
tOEHZ
OE HIGH to Output High-Z[15, 16, 17]
3.0
0
3.0
0
3.0
3.4
0
3.0
ns
ns
3.4
ns
Setup Times
tAS
Address Setup Before CLK Rise
1.4
1.4
1.5
ns
tADS
ADSC, ADSP Setup Before CLK Rise
1.4
1.4
1.5
ns
tADVS
ADV Setup Before CLK Rise
1.4
1.4
1.5
ns
tWES
GW, BWE, BWX Setup Before CLK Rise
1.4
1.4
1.5
ns
tDS
Data Input Setup Before CLK Rise
1.4
1.4
1.5
ns
tCES
Chip Enable Setup Before CLK Rise
1.4
1.4
1.5
ns
tAH
Address Hold After CLK Rise
0.4
0.4
0.5
ns
tADH
ADSP, ADSC Hold After CLK Rise
0.4
0.4
0.5
ns
tADVH
ADV Hold After CLK Rise
0.4
0.4
0.5
ns
tWEH
GW, BWE, BWX Hold After CLK Rise
0.4
0.4
0.5
ns
tDH
Data Input Hold After CLK Rise
0.4
0.4
0.5
ns
tCEH
Chip Enable Hold After CLK Rise
0.4
0.4
0.5
ns
Hold Times
Notes
14. This part has an internal voltage regulator; tPOWER is the time that the power needs to be supplied above VDD(minimum) initially before a read or write operation can
be initiated.
15. tCHZ, tCLZ,tOELZ, and tOEHZ are specified with AC test conditions shown in part (b) of AC Test Loads and Waveforms on page 23. Transition is measured ±200 mV
from steady-state voltage.
16. At any supplied voltage and temperature, tOEHZ is less than tOELZ and tCHZ is less than tCLZ to eliminate bus contention between SRAMs when sharing the same data
bus. These specifications do not imply a bus contention condition, but reflect parameters guaranteed over worst case user conditions. Device is designed to achieve
High-Z before Low-Z under the same system conditions.
17. This parameter is sampled and not 100% tested.
Document #: 001-15145 Rev. *A
Page 24 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
Switching Waveforms
Figure 3 shows read cycle timing.[18]
Figure 3. Read Cycle Timing
t CYC
CLK
t
t
ADS
CH
t
CL
t
ADH
ADSP
t ADS
tADH
ADSC
t AS
tAH
A1
ADDRESS
A2
t WES
A3
Burst continued with
new base address
tWEH
GW, BWE,
BWx
t CES
Deselect
cycle
tCEH
CE
t ADVS
tADVH
ADV
ADV
suspends
burst.
OE
t OEHZ
t CLZ
Data Out (Q)
High-Z
Q(A1)
t OEV
t CO
t OELZ
t DOH
Q(A2)
t CHZ
Q(A2 + 1)
Q(A2 + 2)
Q(A2 + 3)
Q(A2)
Q(A2 + 1)
t CO
Burst wraps around
to its initial state
Single READ
BURST READ
DON’T CARE
UNDEFINED
Note
18. On this diagram, when CE is LOW: CE1 is LOW, CE2 is HIGH, and CE3 is LOW. When CE is HIGH: CE1 is HIGH, CE2 is LOW, or CE3 is HIGH.
Document #: 001-15145 Rev. *A
Page 25 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
Switching Waveforms (continued)
Figure 4 shows write cycle timing.[18, 19]
Figure 4. Write Cycle Timing
t CYC
CLK
tCH
t ADS
tCL
tADH
ADSP
t ADS
ADSC extends burst
tADH
t ADS
tADH
ADSC
t AS
tAH
A1
ADDRESS
A2
A3
Byte write signals are
ignored for first cycle when
ADSP initiates burst
t WES tWEH
BWE,
BW X
t WES tWEH
GW
t CES
tCEH
CE
t
t
ADVS ADVH
ADV
ADV suspends burst
OE
t DS
Data In (D)
High-Z
t
OEHZ
tDH
D(A1)
D(A2)
D(A2 + 1)
D(A2 + 1)
D(A2 + 2)
D(A2 + 3)
D(A3)
D(A3 + 1)
D(A3 + 2)
Data Out (Q)
BURST READ
Single WRITE
BURST WRITE
DON’T CARE
Extended BURST WRITE
UNDEFINED
Note
19. Full width write can be initiated by either GW LOW; or by GW HIGH, BWE LOW, and BWX LOW.
Document #: 001-15145 Rev. *A
Page 26 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
Switching Waveforms (continued)
Figure 5 shows read-write cycle timing.[18, 20, 21]
Figure 5. Read/Write Cycle Timing
tCYC
CLK
tCL
tCH
t ADS
tADH
t AS
tAH
ADSP
ADSC
ADDRESS
A1
A2
A3
A4
A5
A6
t WES tWEH
BWE,
BW X
t CES
tCEH
CE
ADV
OE
t DS
tCO
tDH
t OELZ
Data In (D)
High-Z
tCLZ
Data Out (Q)
High-Z
Q(A1)
Back-to-Back READs
tOEHZ
D(A5)
D(A3)
Q(A4)
Q(A2)
Single WRITE
Q(A4+1)
Q(A4+2)
BURST READ
DON’T CARE
D(A6)
Q(A4+3)
Back-to-Back
WRITEs
UNDEFINED
Notes
20. The data bus (Q) remains in high-Z following a write cycle, unless a new read access is initiated by ADSP or ADSC.
21. GW is HIGH.
Document #: 001-15145 Rev. *A
Page 27 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
Switching Waveforms (continued)
Figure 6 shows ZZ mode timing.[22, 23]
Figure 6. ZZ Mode Timing
CLK
t
ZZ
I
t ZZREC
ZZ
t ZZI
SUPPLY
I DDZZ
t RZZI
ALL INPUTS
(except ZZ)
Outputs (Q)
DESELECT or READ Only
High-Z
DON’T CARE
Notes
22. Device must be deselected when entering ZZ mode. See the section Truth Table on page 10 for all possible signal conditions to deselect the device.
23. DQs are in High-Z when exiting ZZ sleep mode.
Document #: 001-15145 Rev. *A
Page 28 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
Ordering Information
Not all of the speed, package, and temperature ranges are available. Please contact your local sales representative or
visit www.cypress.com for actual products offered.
Speed
(MHz)
167
Ordering Code
CY7C1480BV33-167AXC
Package
Diagram
Part and Package Type
51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Pb-Free
Operating
Range
Commercial
CY7C1482BV33-167AXC
CY7C1480BV33-167BZC
51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm)
CY7C1482BV33-167BZC
CY7C1480BV33-167BZXC 51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm) Pb-Free
CY7C1482BV33-167BZXC
CY7C1486BV33-167BGC
CY7C1486BV33-167BGXC
CY7C1480BV33-167AXI
51-85167 209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm)
209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm) Pb-Free
51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Pb-Free
lndustrial
CY7C1482BV33-167AXI
CY7C1480BV33-167BZI
51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm)
CY7C1482BV33-167BZI
CY7C1480BV33-167BZXI
51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm) Pb-Free
CY7C1482BV33-167BZXI
CY7C1486BV33-167BGI
CY7C1486BV33-167BGXI
200
CY7C1480BV33-200AXC
51-85167 209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm)
209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm) Pb-Free
51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Pb-Free
Commercial
CY7C1482BV33-200AXC
CY7C1480BV33-200BZC
51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm)
CY7C1482BV33-200BZC
CY7C1480BV33-200BZXC 51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm) Pb-Free
CY7C1482BV33-200BZXC
CY7C1486BV33-200BGC
CY7C1486BV33-200BGXC
CY7C1480BV33-200AXI
51-85167 209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm)
209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm) Pb-Free
51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Pb-Free
lndustrial
CY7C1482BV33-200AXI
CY7C1480BV33-200BZI
51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm)
CY7C1482BV33-200BZI
CY7C1480BV33-200BZXI
51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm) Pb-Free
CY7C1482BV33-200BZXI
CY7C1486BV33-200BGI
CY7C1486BV33-200BGXI
Document #: 001-15145 Rev. *A
51-85167 209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm)
209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm) Pb-Free
Page 29 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
Ordering Information
(continued)
Not all of the speed, package, and temperature ranges are available. Please contact your local sales representative or
visit www.cypress.com for actual products offered.
Speed
(MHz)
250
Ordering Code
CY7C1480BV33-250AXC
Package
Diagram
Part and Package Type
51-85050 100-Pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Pb-Free
Operating
Range
Commercial
CY7C1482BV33-250AXC
CY7C1480BV33-250BZC
51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm)
CY7C1482BV33-250BZC
CY7C1480BV33-250BZXC 51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm) Pb-Free
CY7C1482BV33-250BZXC
CY7C1486BV33-250BGC
CY7C1486BV33-250BGXC
CY7C1480BV33-250AXI
51-85167 209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm)
209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm) Pb-Free
51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Pb-Free
Industrial
CY7C1482BV33-250AXI
CY7C1480BV33-250BZI
51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm)
CY7C1482BV33-250BZI
CY7C1480BV33-250BZXI
51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4 mm) Pb-Free
CY7C1482BV33-250BZXI
CY7C1486BV33-250BGI
CY7C1486BV33-250BGXI
Document #: 001-15145 Rev. *A
51-85167 209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm)
209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm) Pb-Free
Page 30 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
Package Diagrams
Figure 7. 100-Pin Thin Plastic Quad Flatpack (14 x 20 x 1.4 mm)
16.00±0.20
1.40±0.05
14.00±0.10
81
100
80
1
20.00±0.10
22.00±0.20
0.30±0.08
0.65
TYP.
30
12°±1°
(8X)
SEE DETAIL
A
51
31
50
0.20 MAX.
0.10
1.60 MAX.
R 0.08 MIN.
0.20 MAX.
0° MIN.
SEATING PLANE
STAND-OFF
0.05 MIN.
0.15 MAX.
0.25
NOTE:
1. JEDEC STD REF MS-026
GAUGE PLANE
0°-7°
R 0.08 MIN.
0.20 MAX.
2. BODY LENGTH DIMENSION DOES NOT INCLUDE MOLD PROTRUSION/END FLASH
MOLD PROTRUSION/END FLASH SHALL NOT EXCEED 0.0098 in (0.25 mm) PER SIDE
BODY LENGTH DIMENSIONS ARE MAX PLASTIC BODY SIZE INCLUDING MOLD MISMATCH
3. DIMENSIONS IN MILLIMETERS
0.60±0.15
0.20 MIN.
1.00 REF.
DETAIL
Document #: 001-15145 Rev. *A
A
51-85050-*B
Page 31 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
Package Diagrams
(continued)
Figure 8. 165-Ball FBGA (15 x 17 x 1.4 mm)
PIN 1 CORNER
BOTTOM VIEW
TOP VIEW
Ø0.05 M C
PIN 1 CORNER
Ø0.25 M C A B
Ø0.45±0.05(165X)
1
2
3
4
5
6
7
8
9
10
11
11
10
9
8
7
6
5
4
3
2
1
A
B
B
C
C
1.00
A
D
D
F
F
G
G
H
J
14.00
E
17.00±0.10
E
H
J
K
L
L
7.00
K
M
M
N
N
P
P
R
R
A
1.00
5.00
0.35
0.15 C
+0.05
-0.10
0.53±0.05
0.25 C
10.00
B
15.00±0.10
0.15(4X)
SEATING PLANE
Document #: 001-15145 Rev. *A
1.40 MAX.
0.36
C
51-85165-*A
Page 32 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
Package Diagrams
(continued)
Figure 9. 209-Ball FBGA (14 x 22 x 1.76 mm)
51-85167-**
Document #: 001-15145 Rev. *A
Page 33 of 34
[+] Feedback
CY7C1480BV33
CY7C1482BV33, CY7C1486BV33
Document History Page
Document Title: CY7C1480BV33/CY7C1482BV33/CY7C1486BV33, 72-Mbit (2M x 36/4M x 18/1M x 72)
Pipelined Sync SRAM
Document Number: 001-15145
REV.
ECN NO. Issue Date
**
1024385
See ECN
*A
2183566
See ECN
Orig. of
Change
Description of Change
VKN/KKVTMP New Data Sheet
VKN/PYRS
Converted from preliminary to final
Added footnote 14 related to IDD
© Cypress Semiconductor Corporation, 2007-2008. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of
any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for
medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as
critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document #: 001-15145 Rev. *A
Revised March 05, 2008
Page 34 of 34
i486 is a trademark and Intel and Pentium are registered trademarks of Intel Corporation. All products and company names mentioned in this document may be the trademarks of their respective holders
[+] Feedback