ELECTRONICS Transient Voltage Suppressors 1.5SMC Series Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Transient Voltage Suppressors - 1.5SMC Series Features UNI 1. Halogen-free 2. Rohs compliant 3. Typical maximum temperature coefficient 4. ΔVBR = 0.1% x VBR@25°C x ΔT 5. Glass passivated Chip junction in DO-214AB package BI 6. 1500W peak pulse capadility at 10×1000μs waveform, repetition rate (duty cycles):0.01% 7. Fast response time:typically less than 1.0ps from 0 Volts to BV min 8. Excellent clamping capability 9. Low incremental surge resistance 10. Typical IR less than 5μA above 12V BI Cathode 11. High temperature soldering guaranteed: 260°C/40 seconds / 0.375”, Anode 12. (9.5mm) lead length, 5lbs., (2.3kg) tension 13. Plastic package has underwriters laboratory flammability classification UNI 94v-0 Applications TVS devices are ideal for the protection of I/O interfaces,VCC bus and other vulnerable circuits used in telecom, computer, industrial and consumer electronic applications. Mechanical Characteristics Rating Symbol Value Units Peak Pulse Power Dissipation at TA=25°C by 10x1000μs waveform (Fig.1)(Note 1), (Note 2) PPPM 1500 Watts Power Dissipation on infinite heat sink at TA=50°C PD 6.5 Watts IFSM 200 Amps VF 3.5/5.0 V Operating junction and Storage Temperature Range. TJ,TSTG -55°C to 150°C °C Typical Thermal Resistance Junction to Lead RuJL 15 °C/W Typical Thermal Resistance Junction to Ambient RuJA 75 °C/W Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3) Maximum Instantaneous Forward Voltage at 25A for Unidirectional only (Note 4) Notes: 1. Non-repetitive current pulse , per Fig. 3 and derated above TA = 25°C per Fig. 2. 2. Measured on 8.3ms single half sine wave or equivalent square wave, duty cycle=4 perminute maximum. 3. VF<3.5V for devices of VBR < 200V and VF<5.0V for devices of VBR > 201V. Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:1 Transient Voltage Suppressors - 1.5SMC Series Electriacl Characteristics (UNI) (BI) Reverse Stand-Off Voltage VRWM(V) 1.5SMC6.8A 1.5SMC6.8CA 5.80 1.5SMC7.5A 1.5SMC7.5CA 6.40 Type Number Breakdown Voltage@IT Test Current VBR MIN.(V) VBR MAX.(V) 6.40 7.25 IT(mA) 10 7.22 8.30 10 Maximum Clamping Voltage@IPP VC(V) Peak Pulse Current 9.2 IPP(A) 163.0 10.3 145.7 Reverse Leakage @VRWM IR(µA) 800 800 1.5SMC8.2A 1.5SMC8.2CA 7.02 7.78 8.95 10 12.0 125.0 200 1.5SMC9.1A 1.5SMC9.1CA 7.78 8.33 9.58 1 12.9 116.3 100 1.5SMC10A 1.5SMC10CA 8.55 9.44 10.82 1 13.6 110.3 50 1.5SMC11A 1.5SMC11CA 9.40 10.00 11.50 1 18.2 82.5 5 1.5SMC12A 1.5SMC12CA 10.20 11.10 12.80 1 19.9 75.4 5 1.5SMC13A 1.5SMC13CA 11.10 12.20 14.00 1 21.5 69.8 5 1.5SMC15A 1.5SMC15CA 12.80 14.40 16.50 1 24.4 61.5 5 1.5SMC16A 1.5SMC16CA 13.60 15.60 17.90 1 26.0 57.7 5 1.5SMC18A 1.5SMC18CA 15.30 16.70 19.20 1 29.2 51.4 5 1.5SMC20A 1.5SMC20CA 17.10 18.90 21.70 1 32.4 46.3 5 1.5SMC22A 1.5SMC22CA 18.80 20.00 23.30 1 35.5 42.3 5 1.5SMC24A 1.5SMC24CA 20.50 22.20 25.50 1 38.9 38.6 5 1.5SMC27A 1.5SMC27CA 23.10 24.40 28.00 1 42.1 35.7 5 1.5SMC30A 1.5SMC30CA 25.60 28.90 33.20 1 48.4 31.0 5 1.5SMC33A 1.5SMC33CA 28.20 31.10 35.80 1 53.3 28.2 5 1.5SMC36A 1.5SMC36CA 20.80 33.30 38.30 1 58.1 25.9 5 1.5SMC39A 1.5SMC39CA 33.30 36.70 42.20 1 64.5 23.3 5 1.5SMC43A 1.5SMC43CA 36.80 40.00 46.00 1 69.4 21.7 5 1.5SMC47A 1.5SMC47CA 40.20 44.40 51.10 1 72.7 20.6 5 1.5SMC51A 1.5SMC51CA 43.60 47.80 54.90 1 82.4 18.2 5 1.5SMC56A 1.5SMC56CA 47.80 50.00 57.50 1 87.1 17.3 5 1.5SMC62A 1.5SMC62CA 53.00 56.70 65.20 1 96.8 15.5 5 1.5SMC68A 1.5SMC68CA 58.10 64.40 74.10 1 103.0 14.6 5 1.5SMC75A 1.5SMC75CA 64.10 71.10 81.80 1 121.0 12.4 5 1.5SMC82A 1.5SMC82CA 70.10 77.80 89.50 1 137.0 11.0 5 1.5SMC91A 1.5SMC91CA 77.80 86.70 99.70 1 146.0 10.3 5 1.5SMC100A 1.5SMC100CA 85.50 94.40 108.20 1 162.0 9.3 5 1.5SMC110A 1.5SMC110CA 94.00 100.00 115.50 1 177.0 8.5 5 1.5SMC120A 1.5SMC120CA 102.00 111.00 128.00 1 193.0 7.8 5 1.5SMC130A 1.5SMC130CA 111.00 122.00 140.50 1 209.0 7.2 5 1.5SMC150A 1.5SMC150CA 128.00 144.00 165.50 1 243.0 6.2 5 1.5SMC180A 1.5SMC180CA 154.00 167.00 192.60 1 292.0 5.1 5 1.5SMC200A 1.5SMC200CA 171.00 189.00 217.50 1 324.0 4.6 5 1.5SMC220A 1.5SMC220CA 185.00 209.00 243.20 1 356.0 4.3 5 1.5SMC250A 1.5SMC250CA 214.00 242.00 272.00 1 405.0 3.7 5 Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:2 Transient Voltage Suppressors - 1.5SMC Series Ratings and Characteristic Curves Figure 1 - Peak Pulse Power Rating Figure 2 - Pulse Derating Curve Figure 3 - Pulse Waveform Figure 4 - Typical Junction Capacitance Figure 5 - Steady State Power Derating Curve Figure 6 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional Only Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:3 Transient Voltage Suppressors - 1.5SMC Series Soldering Parameters Feflow Condition Pre Heat Lead-free assembly - Temperature Min (T s(min)) 150°C - Temperature Max (T s(min)) 200°C - Time (min to max) (t s) 60-180 secs Average ramp up rate (Liquidus Temp (TL) to peak 3°C/second max TS(max) to TL - Ramp-up Rate 3°C/second max - Temperature (T L) (Liquidus) Reflow 217°C - Time (min to max) (t s) 60-150 seconds 260+0/-5 °C Peak Temperature (T P) Time within 5°C of actual peak Temperature (t p) 20-40 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (T P) 8 minutes Max. Do not exceed 280°C Physical Specifications tp TP one Ramp-up Temperature (T) TL tL Critical Z P TL to T Weight 0.007 ounce, 0.21 grams JEDEC DO214AA. Molded plastic body over glass passivated junction Color band denotes cathode except Bidirectional. Matte Tin-plated leads, Solderable per JESD22-B102D Case Ts(max) Ts(min) Ramp-down ts Polarity Termina Preheat Time (t) Circuit Protection System Environmental Specifications Temperature Cycle JESD22-A104 Pressure Cooker JESD 22-A102 High Temp. Storage JESD22-A103 HTRB JESD22-A108 Thermal Shock JESD22-A106 Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:4 Transient Voltage Suppressors - 1.5SMC Series Dimensions Unit:mm DO-214AB (SMC J-Bend) DIM Inches Millimeters Min Max Min Max A 0.114 0.126 2.900 3.200 B 0.260 0.280 6.600 7.110 C 0.220 0.245 5.590 6.220 D 0.079 0.103 2.060 2.620 E 0.030 0.060 0.760 1.520 F - 0.008 - 0.203 G 0.305 0.320 7.750 8.130 H 0.006 0.012 0.152 0.305 I 0.129 - 3.300 - J 0.094 - 2.400 - K - 0.165 - 4.200 L 0.094 - 2.400 - Warehouse Storage Conditions of Products · Storage Conditions: 1. Storage Temperature: -10°C~+40°C 2. Relative Humidity:≤75%RH 3. Keep away from corrosive atmosphere and sunlight. · Period of Storage: 1 year Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:5 RuiLongYuan Electronics Co., Ltd. · Reproducing and modifying information of the document is prohibited without permission from Ruilongyuan International Inc. · Ruilongyuan International Inc. reserves the rights to make changes of the content herein the document anytime without notification. Please refer to our website for the latest document. · Ruilongyuan International Inc. disclaims any and all liability arising out of the application or use of any product including damages incidentally and consequentially occurred. · Ruilongyuan International Inc. does not assume any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. · Applications shown on the herein document are examples of standard use and operation. Customers are responsible in comprehending the suitable use in particular applications.Ruilongyuan International Inc. makes no representation or warranty that such applications will be suitable for the specifed use without further testing or modifcation. · The products shown herein are not designed and authorized for equipments requiring high level of reliability or relating to human life and for any applications concerning life-saving or life-sustaining, such as medical instruments, transportation equipment,aerospace machinery et cetera. Customers using or selling these products for use in such applications do so at their own risk and agree to fullyindemnify Ruilongyuan International Inc. for any damages resulting from such improper use or sale. Tel: +86-755-8290 8296 Circuit Protection System Fax: +86-755-8290 8002 E-mail: [email protected] Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:6