MAXIM DS1100L_11

19-5736; Rev 3/11
DS1100L
3.3V 5-Tap Economy Timing Element (Delay Line)
GENERAL DESCRIPTION
FEATURES
The DS1100L is a 3.3V version of the DS1100. It
is characterized for operation over the range 3.0V
to 3.6V. The DS1100L series delay lines have
five equally spaced taps providing delays from
4ns to 500ns. These devices are offered in
surface-mount packages to save PCB area. Low
cost and superior reliability over hybrid
technology is achieved by the combination of a
100% silicon delay line and industry-standard
µMAX and SO packaging. The DS1100L 5-tap
silicon delay line reproduces the input-logic state
at the output after a fixed delay as specified by
the extension of the part number after the dash.
The DS1100L is designed to reproduce both
leading and trailing edges with equal precision.
Each tap is capable of driving up to 10 74LS
loads.











All-Silicon Timing Circuit
Five Taps Equally Spaced
Delays are Stable and Precise
Both Leading- and Trailing-Edge Accuracy
3.3V Version of the DS1100
Low-Power CMOS
TTL-/CMOS-Compatible
Vapor-Phase and IR Solderable
Custom Delays Available
Fast-Turn Prototypes
Delays Specified Over Both Commercial and
Industrial Temperature Ranges
PIN ASSIGNMENT
Maxim can customize standard products to meet
special needs.
IN
1
8
VCC
TAP 2
2
7
TAP 1
TAP 4
3
6
TAP 3
GND
4
5
TAP 5
DS1100LZ SO (150 mils)
DS1100LU µMAX®
PIN DESCRIPTION
TAP 1 to TAP 5
VCC
GND
IN
µMAX is a registered trademark of Maxim Integrated Products, Inc.
1 of 7
- TAP Output Number
- +3.3V
- Ground
- Input
DS1100L
ABSOLUTE MAXIMUM RATINGS
Voltage Range on Any Pin Relative to Ground ........................... -0.5V to +6.0V
Short-Circuit Output Current ...................................................... 50mA for 1s
Operating Temperature Range .................................................... -40°C to +85°C
Storage Temperature Range ........................................................ -55°C to +125°C
Lead Temperature (soldering, 10s) .............................................. +300°C
Soldering Temperature (reflow)
Lead(Pb)-free........................................................................... +260°C
Containing lead(Pb) ................................................................. +240°C
This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of
this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect device reliability.
DC ELECTRICAL CHARACTERISTICS
(VCC = 3.0V to 3.6V; TA = -40°C to +85°C, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
Supply Voltage
VCC
3.0
High-Level
VIH
2.0
Input Voltage
Low-Level
VIL
-0.3
Input Voltage
Input-Leakage
-1.0
II
0.0V ≤ VI ≤ VCC
Current
Active Current
ICC
VCC = Max; Freq. = 1MHz
High-Level
VCC = Min. VOH = 2.3
IOH
Output Current
Low-Level
VCC = Min. VOL = 0.5
8
IOL
Output Current
TYP
3.3
MAX
3.6
VCC +
0.3
UNITS
V
NOTES
5
V
5
0.8
V
5
+1.0
μA
10
mA
-1
6, 8
mA
mA
AC ELECTRICAL CHARACTERISTICS
(VCC = 3.0V to 3.6V; TA = -40°C to +85°C, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
20% of
Input
tWI
Tap 5
Pulse Width
tPLH
+25°C 3.3V
-2
Input-to-Tap
0°C to +70°C
-3
tPLH,
Delay Tolerance
tPHL
(Delays ≤ 40ns)
-40°C to +85°C
-4
Input-to-Tap
Delay Tolerance
(Delays > 40ns)
Output Rise or Fall
Time
Power-Up Time
Input Period
tPLH,
tPHL
TYP
MAX
UNITS
NOTES
ns
9
1, 3, 4, 7
1, 2, 3,
4, 7
1, 2, 3,
4, 7
1, 3, 4, 7
1, 2, 3,
4, 7
1, 2, 3,
4, 7
Table 1
+2
ns
Table 1
+3
ns
Table 1
+4
ns
+25°C 3.3V
-5
Table 1
+5
%
0°C to +70°C
-8
Table 1
+8
%
-40°C to +85°C
-13
Table 1
+13
%
2.0
2.5
ns
200
μs
ns
tOF, tOR
tPU
Period
2(tWI)
9
CAPACITANCE
(TA = +25°C, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
Input Capacitance
CIN
2 of 7
MIN
TYP
5
MAX
10
UNITS
pF
NOTES
DS1100L
NOTES:
1) Initial tolerances are ± with respect to the nominal value at +25°C and VCC = 3.3V for both leading
and trailing edge.
2) Temperature and voltage tolerance is with respect to the nominal delay value over the stated
temperature range, and a supply-voltage range of 3.0V to 3.6V.
3) All tap delays tend to vary unidirectionally with temperature or voltage changes. For example, if TAP
1 slows down, all other taps also slow down; TAP3 can never be faster than TAP2.
4) Intermediate delay values are available on a custom basis. For further information, contact the factory
at [email protected].
5) All voltages are referenced to ground.
6) Measured with outputs open.
7) See Test Conditions section at the end of this data sheet.
8) Frequencies higher than 1MHz result in higher ICC values.
9) At or near maximum frequency the delay accuracy can vary and will be application sensitive (i.e.,
decoupling, layout).
Figure 1. LOGIC DIAGRAM
Figure 2. TIMING DIAGRAM: SILICON DELAY LINE
3 of 7
DS1100L
TERMINOLOGY
Period: The time elapsed between the leading edge of the first pulse and the leading edge of the
following pulse.
tWI (Pulse Width): The elapsed time on the pulse between the 1.5V point on the leading edge and the
1.5V point on the trailing edge or the 1.5V point on the trailing edge and the 1.5V point on the leading
edge.
tRISE (Input Rise Time): The elapsed time between the 20% and the 80% point on the leading edge of the
input pulse.
tFALL (Input Fall Time): The elapsed time between the 80% and the 20% point on the trailing edge of the
input pulse.
tPLH (Time Delay, Rising): The elapsed time between the 1.5V point on the leading edge of the input
pulse and the 1.5V point on the leading edge of any tap output pulse.
tPHL (Time Delay, Falling): The elapsed time between the 1.5V point on the trailing edge of the input
pulse and the 1.5V point on the trailing edge of any tap output pulse.
TEST SETUP DESCRIPTION
Figure 3 illustrates the hardware configuration used for measuring the timing parameters on the
DS1100L. The input waveform is produced by a precision pulse generator under software control. Time
delays are measured by a time interval counter (20ps resolution) connected between the input and each
tap. Each tap is selected and connected to the counter by a VHF switch control unit. All measurements
are fully automated, with each instrument controlled by a central computer over an IEEE 488 bus.
TEST CONDITIONS INPUT:
Ambient Temperature:
Supply Voltage (VCC):
Input Pulse:
Source Impedance:
Rise and Fall Time:
Pulse Width:
Period:
25°C ±3°C
3.3V ±0.1V
High = 3.0V ±0.1V
Low = 0.0V ±0.1V
50Ω max
3.0ns max (measured between 10% and 90%)
500ns (1μs for -500 version)
1μs (2μs for -500 version)
OUTPUT:
Each output is loaded with the equivalent of one 74F04 input gate. Delay is measured at the 1.5V level on
the rising and falling edge.
Note: Above conditions are for test only and do not restrict the operation of the device under other
data sheet conditions.
4 of 7
DS1100L
Figure 3. TEST CIRCUIT
Table 1. DS1100L PART NUMBER DELAY
PART
DS1100L-xxx
-20
-25
-30
-35
-40
-45
-50
-60
-75
-100
-125
-150
-175
-200
-250
-300
-500
TAP 1
4
5
6
7
8
9
10
12
15
20
25
30
35
40
50
60
100
NOMINAL DELAYS (ns)
TAP 2
TAP 3
TAP 4
8
12
16
10
15
20
12
18
24
14
21
28
16
24
32
18
27
36
20
30
40
24
36
48
30
45
60
40
60
80
50
75
100
60
90
120
70
105
140
80
120
160
100
150
200
120
180
240
200
300
400
5 of 7
TAP 5
20
25
30
35
40
45
50
60
75
100
125
150
175
200
250
300
500
DS1100L
ORDERING INFORMATION
PART
DS1100LZ-xxx
DS1100LZ-xxx/T&R
DS1100LZ-xxx+
DS1100LZ-xxx+T
DS1100LU-xxx
DS1100LU-xxx/T&R
DS1100LU-xxx+
DS1100LU-xxx+T
TEMP RANGE
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
PIN-PACKAGE
8 SO
8 SO
8 SO
8 SO
8 µMAX
8 µMAX
8 µMAX
8 µMAX
xxx Denotes total time delay (ns) (see Table 1).
+Denotes a lead(Pb)-free/RoHS-compliant package.
T&R and T = Tape and reel.
PACKAGE INFORMATION
For the latest package outline information and land patterns (footprints), go to www.maxim-ic.com/packages. Note that a “+”,
“#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the
drawing pertains to the package regardless of RoHS status.
PACKAGE TYPE
PACKAGE CODE
OUTLINE NO.
LAND PATTERN NO.
8 SO (150 mils)
S8+4
21-0041
90-0096
8 µMAX
U8+1
21-0036
90-0092
6 of 7
DS1100L
REVISION HISTORY
REVISION
DATE
DESCRIPTION
PAGES
CHANGED
3/11
Changed µSOP package type to µMAX; updated the Absolute
Maximum Ratings section; added the customer support email address to
the electrical characteristics Note 4; added the Ordering Information
and Package Information tables
1−6
7 of 7
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit
patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
M a x i m I n t e g r a t e d P r o d u c t s , 1 2 0 S a n G a b r i e l D r iv e , S u n n y v a le , C A 9 4 0 8 6 4 0 8- 7 3 7 - 7 6 0 0
 2011 Maxim Integrated Products
Maxim is a registered trademark of Maxim Integrated Products.