TI DS125BR401

DS125BR401
www.ti.com
SNLS419C – JULY 2012 – REVISED APRIL 2013
Low-Power 12.5-Gbps 4-Lane Repeater With Input Equalization and Output De-Emphasis
Check for Samples: DS125BR401
FEATURES
DESCRIPTION
•
The DS125BR401 is an extremely low-power highperformance multi-protocol repeater/redriver designed
to support four lanes of PCIe Gen-3/2/1, 10G-KR,
and other high-speed interface serial protocols up to
12.5 Gbps. The receiver's continuous time linear
equalizer (CTLE) provides a boost of up to +30 dB at
6.25 GHz (12.5 Gbps) in each of its eight channels
and is capable of opening an input eye that is
completely closed due to inter symbol interference
(ISI) induced by interconnect medium such as 30in+
backplane traces or 8m+ copper cables, hence
enabling host controllers to ensure an error free endto-end link. The transmitter provides a de-emphasis
boost of up to -12 dB and output voltage amplitude
control from 700 mV to 1300 mV to allow maximum
flexibility in the physical placement within the
interconnect channel.
1
2
•
•
•
•
•
•
•
•
•
Comprehensive Family, Proven System
Interoperability
– DS125BR111 : One-Lane Bidirectional
Repeater
– DS125BR210 : Two-Channel Unidirectional
Repeater
– DS125BR401 : Four-Lane Bidirectional
Repeater
– DS125BR800 : Eight-Channel Unidirectional
Repeater
– DS125MB203 : Two-Port 2:1/1:2 Mux/Switch
– DS125DF410 : Four-Channel Unidirectional
Retimer With CDR
Low 65-mW/Channel (Typ) Power
Consumption, With Option to Power Down
Unused Channels
Transparent Management of Link Training
Protocol for PCIe and 10G-KR
Advanced Signal Conditioning Features
– Receive Equalization up to 30 dB at 6.25
GHz
– Transmit De-Emphasis up to -12 dB
– Transmit Output Voltage Control: 700 mV to
1300 mV
Programmable via Pin Selection, EEPROM, or
SMBus Interface
Single Supply Voltage: 2.5 V or 3.3 V
(Selectable)
−40°C to 85°C Operating Temperature Range
5-kV HBM ESD Rating
Flow-Thru Pinout in 10mmx5.5mm 54-Pin
Leadless WQFN Package
Supported Protocols
– SAS/SATA (up to 6 Gbps), Fibre Channel
(up to 10GFC)
– PCIe Gen-3/2/1, 10G-KR, 10GbE, XAUI,
RXAUI
– sRIO, Infiniband, Interlaken, CPRI, OBSAI
– Other Proprietary Interface up to 12.5 Gbps
When operating in 10G-KR, and PCIe Gen-3 mode,
the DS125BR401 transparently allows the host
controller and the end point to optimize the full link
and negotiate transmit equalizer coefficients. This
seamless management of the link training protocol
ensures guaranteed system level interoperability with
minimum latency. With a low power consumption of
65 mW/channel (typ) and option to turn-off unused
channels, the DS125BR401 enables energy efficient
system design. A single supply of 3.3 V or 2.5 V is
required to power the device.
The programmable settings can be applied easily via
pins, software (SMBus or I2C), or loaded via an
external EEPROM. When operating in the EEPROM
mode, the configuration information is automatically
loaded on power up, which eliminates the need for an
external microprocessor or software driver.
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2012–2013, Texas Instruments Incorporated
DS125BR401
SNLS419C – JULY 2012 – REVISED APRIL 2013
www.ti.com
Typical Application
4
TX
ASIC
or
PCIe EP
Connector
4
RX
DS125BR401
4
RX
System Board
Root Complex
Connector
4
ard
Bo ce
Tra
TX
DS125BR401
Block Diagram - Detail View Of Channel (1 Of 8)
VOD/DeEMPHASIS
CONTROL
VDD
Auto/Manual
RXDET
INx_n+
RATE
DET
DEMA/B
SMBus
EQ
OUTBUF
INx_n-
EQA/B
SMBus
2
OUTx_n+
OUTx_n-
IDLE
DET
TX Idle Enable
SMBus
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
DS125BR401
www.ti.com
SNLS419C – JULY 2012 – REVISED APRIL 2013
DEMA0/SDA
ENSMB
EQB1/AD2
EQB0/AD3
47
46
DEMA1/SCL
50
48
VDD
49
PWDN
51
DEMB0/AD1
53
52
DEMB1/AD0
54
Pin Diagram
SMBUS AND CONTROL
OUTB_0+
1
45
INB_0+
OUTB_0-
2
44
INB_0-
OUTB_1+
3
43
INB_1+
OUTB_1-
4
42
INB_1-
OUTB_2+
5
41
VDD
OUTB_2-
6
40
INB_2+
OUTB_3+
7
39
INB_2-
38
INB_3+
37
INB_3-
OUTB_3-
8
VDD
9
DAP = GND
OUTA_2+
16
30
OUTA_2-
INA_3+
17
29
OUTA_3+
INA_3-
18
28
OUTA_3-
EQA1
ALL_DONE
15
INA_2-
26
INA_2+
27
OUTA_1-
31
25
32
SD_TH/READ_EN
14
VDD_SEL
VDD
24
OUTA_1+
23
33
VIN
OUTA_0-
13
LPBK
34
INA_1-
22
12
RXDET
INA_1+
21
OUTA_0+
20
VDD
35
EQA0
36
11
MODE
10
19
INA_0+
INA_0-
NOTE: Above 54-lead WQFN graphic is a TOP VIEW, looking down through the package.
DS125BR401 Pin Diagram 54-lead WQFN Package
See Package Number NJY0054A
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
3
DS125BR401
SNLS419C – JULY 2012 – REVISED APRIL 2013
www.ti.com
Pin Descriptions (1)
Pin Name
Pin Number
I/O, Type
Pin Description
Differential High Speed I/O's
INB_0+,
INB_1+,
INB_2+,
INB_3+,
INB_0- ,
INB_1-,
INB_2-,
INB_3-
OUTB_0+,
OUTB_1+,
OUTB_2+,
OUTB_3+,
INA_0+,
INA_1+,
INA_2+,
INA_3+,
OUTB_0-,
OUTB_1-,
OUTB_2-,
OUTB_3-
INA_0- ,
INA_1-,
INA_2-,
INA_3-
OUTA_0+,
OUTA_1+,
OUTA_2+,
OUTA_3+,
OUTA_0-,
OUTA_1-,
OUTA_2-,
OUTA_3-
45, 44, 43, 42
40, 39, 38, 37
I
Inverting and non-inverting CML differential inputs to the equalizer. Onchip 50Ω termination resistor connects INB_n+ to VDD and INB_n- to
VDD when enabled.
AC coupling required on high-speed I/O
1, 2, 3, 4
5, 6, 7, 8
O
Inverting and non-inverting 50Ω driver outputs with de-emphasis.
Compatible with AC coupled CML inputs.
AC coupling required on high-speed I/O
10, 11, 12, 13
15, 16, 17, 18
I
Inverting and non-inverting CML differential inputs to the equalizer. Onchip 50Ω termination resistor connects INA_n+ to VDD and INA_n- to
VDD when enabled.
AC coupling required on high-speed I/O
35, 34, 33, 32
31, 30, 29, 28
O
Inverting and non-inverting 50Ω driver outputs with de-emphasis.
Compatible with AC coupled CML inputs.
AC coupling required on high-speed I/O
I, LVCMOS
System Management Bus (SMBus) enable pin
Tie 1kΩ to VDD = Register Access SMBus Slave mode
FLOAT = Read External EEPROM (Master SMBUS Mode)
Tie 1kΩ to GND = Pin Mode
Control Pins — Shared (LVCMOS)
ENSMB
48
ENSMB = 1 (SMBUS MODE)
SCL
50
I, LVCMOS,
O, OPEN Drain
ENSMB Master or Slave mode
SMBUS clock input pin is enabled (slave mode).
Clock output when loading EEPROM configuration (master mode).
SDA
49
I, LVCMOS,
O, OPEN Drain
ENSMB Master or Slave mode
The SMBus bidirectional SDA pin is enabled. Data input or open drain
(pull-down only) output.
AD0-AD3
54, 53, 47, 46
I, LVCMOS
ENSMB Master or Slave mode
SMBus Slave Address Inputs. In SMBus mode, these pins are the user
set SMBus slave address inputs.
READ_EN
26
I, LVCMOS
When using an External EEPROM, a transition from high to low starts
the load from the external EEPROM
EQA0, EQA1
EQB0, EQB1
20, 19
46, 47
I, 4-LEVEL,
LVCMOS
EQA[1:0] and EQB[1:0] control the level of equalization of the A/B sides
as shown in . The pins are active only when ENSMB is de-asserted
(low). Each of the 4 A/B channels have the same level unless controlled
by the SMBus control registers. When ENSMB goes high the SMBus
registers provide independent control of each lane. The EQB[1:0] pins
are converted to SMBUS AD2, AD3 inputs. See Table 2.
DEMA0, DEMA1
DEMB0, DEMB1
49, 50
53, 54
I, 4-LEVEL,
LVCMOS
DEMA[1:0] and DEMB[1:0] control the level of de-emphasis of the A/B
sides as shown in . The pins are only active when ENSMB is de-asserted
(low). Each of the 4 A/B channels have the same level unless controlled
by the SMBus control registers. When ENSMB goes high the SMBus
registers provide independent control of each lane. The DEMA[1:0] pins
are converted to SMBUS SCL/SDA and DEMB[1:0] pins are converted to
AD0, AD1 inputs. See Table 3.
MODE
21
I, 4-LEVEL,
LVCMOS
MODE control pin selects operating modes.
Tie 1kΩ to GND = GEN 1,2 and SAS 1,2
Float = Auto Mode Select (for PCIe)
Tie 20kΩ to GND = GEN-3 without De-emphasis
Tie 1kΩ to VDD = GEN-3 with De-emphasis
See Table 6
SD_TH
26
I, 4-LEVEL,
LVCMOS
Controls the internal Signal Detect Threshold.
See Table 5.
ENSMB = 0 (PIN MODE)
(1)
4
LVCMOS inputs without the “Float” conditions must be driven to a logic low or high at all times or operation is not ensured.
Input edge rate for LVCMOS/FLOAT inputs must be faster than 50 ns from 10–90%.
For 3.3V mode operation, VIN pin = 3.3V and the "VDD" for the 4-level input is 3.3V.
For 2.5V mode operation, VDD pin = 2.5V and the "VDD" for the 4-level input is 2.5V.
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
DS125BR401
www.ti.com
SNLS419C – JULY 2012 – REVISED APRIL 2013
Pin Descriptions(1) (continued)
Pin Name
Pin Number
I/O, Type
Pin Description
Control Pins — Both Pin and SMBus Modes (LVCMOS)
RXDET
22
I, 4-LEVEL,
LVCMOS
The RXDET pin controls the receiver detect function. Depending on the
input level, a 50Ω or >50KΩ termination to the power rail is enabled.
See Table 4.
LPBK
23
I, 4-LEVEL,
LVCMOS
Controls the loopback function
Tie 1kΩ to GND = Root Complex Loopback (INA_n to OUTB_n
Float = Normal Operation
Tie 1kΩ to VDD = End-point Loopback (INB_n to OUTA_n)
VDD_SEL
25
I, FLOAT
Controls the internal regulator
Float = 2.5V mode
Tie GND = 3.3V mode
PWDN
52
I, LVCMOS
Tie High = Low power - power down
Tie GND = Normal Operation
See Table 4.
ALL_DONE
27
O, LVCMOS
Valid Register Load Status Output
HIGH = External EEPROM load failed
LOW = External EEPROM load passed
VIN
24
Power
In 3.3V mode, feed 3.3V to VIN
In 2.5V mode, leave floating.
VDD
9, 14,36, 41, 51
Power
Power supply pins CML/analog
2.5V mode, connect to 2.5V
3.3V mode, connect 0.1 µF cap to each VDD pin
GND
DAP
Power
Ground pad (DAP - die attach pad).
Power
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
5
DS125BR401
SNLS419C – JULY 2012 – REVISED APRIL 2013
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings (1)
Supply Voltage (VDD - 2.5V)
-0.5V to +2.75V
Supply Voltage (VIN - 3.3V)
-0.5V to +4.0V
LVCMOS Input/Output Voltage
-0.5V to +4.0V
CML Input Voltage
-0.5V to (VDD+0.5)
CML Input Current
-30 to +30 mA
Junction Temperature
125°C
Storage Temperature
-40°C to +125°C
Lead Temperature Range Soldering (4 sec.)
+260°C
Derate NJY Package
52.6mW/°C above +25°C
ESD Rating
HBM, STD - JESD22-A114F
5 kV
MM, STD - JESD22-A115-A
150 V
CDM, STD - JESD22-C101-D
Thermal Resistance
1000 V
θJC
11.5°C/W
θJA, No Airflow, 4 layer JEDEC
19.1°C/W
For soldering specifications: See application note SNOA549.
(1)
“Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur, including inoperability and degradation of
device reliability and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or
other conditions beyond those indicated in the Recommended Operating Conditions is not implied. The Recommended Operating
Conditions indicate conditions at which the device is functional and the device should not be operated beyond such conditions. Absolute
Maximum Numbers are ensured for a junction temperature range of -40°C to +125°C. Models are validated to Maximum Operating
Voltages only.
Recommended Operating Conditions
Min
Typ
Max
Unit
Supply Voltage (2.5V mode)
2.375
2.5
2.625
V
Supply Voltage (3.3V mode)
3.0
3.3
3.6
V
Ambient Temperature
-40
25
+85
°C
SMBus (SDA, SCL)
3.6
V
Supply Noise up to 50 MHz (1)
100
mVp-p
(1)
Allowed supply noise (mVp-p sine wave) under typical conditions.
Electrical Characteristics
Parameter
Test Conditions
Min
Typ
Max
Unit
VDD = 2.5 V supply,
EQ Enabled,
VOD = 1.0 Vp-p,
RXDET = 1, PWDN = 0
500
700
mW
VIN = 3.3 V supply,
EQ Enabled,
VOD = 1.0 Vp-p,
RXDET = 1, PWDN = 0
660
900
mW
Power
PD
Power Dissipation
LVCMOS / LVTTL DC Specifications
Vih
High Level Input Voltage
2.0
3.6
V
Vil
Low Level Input Voltage
0
0.8
V
Voh
High Level Output Voltage
(ALL_DONE pin)
Ioh = −4mA
Vol
Low Level Output Voltage
(ALL_DONE pin)
Iol = 4mA
6
Submit Documentation Feedback
2.0
V
0.4
V
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
DS125BR401
www.ti.com
SNLS419C – JULY 2012 – REVISED APRIL 2013
Electrical Characteristics (continued)
Parameter
Iih
Test Conditions
Input High Current (PWDN pin)
VIN = 3.6 V,
LVCMOS = 3.6 V
Input High Current with internal
resistors
(4–level input pin)
Iil
Input Low Current (PWDN pin)
VIN = 3.6 V,
LVCMOS = 0 V
Input Low Current with internal
resistors
(4–level input pin)
Min
Max
Unit
-15
Typ
+15
uA
+20
+150
uA
-15
+15
uA
-160
-40
uA
CML Receiver Inputs (IN_n+, IN_n-)
RLrx-diff
0.05 - 7.5 GHz
RX Differential return loss
-15
dB
dB
7.5 - 15 GHz
-5
RLrx-cm
RX Common mode return loss
0.05 - 5 GHz
-10
Zrx-dc
RX DC common mode impedance
Tested at VDD = 2.5 V
40
50
60
Ω
Zrx-diff-dc
RX DC differntial mode impedance
Tested at VDD = 2.5 V
80
100
120
Ω
Vrx-diff-dc
Differential RX peak to peak voltage
(VID)
Tested at pins
0.6
1.0
1.2
V
Vrx-signal-det-diff-pp
Signal detect assert level for active
data signal
SD_TH = F (float),
0101 pattern at 8 Gbps
180
mVp-p
Vrx-idle-det-diff-pp
Signal detect de-assert level for
electrical idle
SD_TH = F (float),
0101 pattern at 8 Gbps
110
mVp-p
dB
High Speed Outputs
Vtx-diff-pp
Output Voltage Differential Swing
Differential measurement with
Out_n+ and OUT_n-,
terminated by 50Ω to GND,
AC-Coupled, VID = 1.0 Vp-p,
DEM0 = 1, DEM1 = 0 (1)
TX de-emphasis ratio
VOD = 1.0 Vp-p,
DEM0 = 0, DEM1 = R,
Gen 1 & 2 modes only
−3.5
dB
TX de-emphasis ratio
VOD = 1.0 Vp-p,
DEM0 = R, DEM1 = R,
Gen 1 & 2 modes only
−6
dB
Vtx-de-ratio_3.5
Vtx-de-ratio_6
0.8
1.0
1.2
mVp-p
TTX-HF-DJ-DD
TX Dj > 1.5 MHz
0.15
UI
TTX-HF-DJ-DD
TX RMS jitter < 1.5 MHz
3.0
ps RMS
TTX-RISE-FALL
Transmitter rise/fall time
20% to 80% of differential output
voltage
TRF-MISMATCH
Transmitter rise/fall mismatch
20% to 80% of differential output
voltage
0.01
0.05 - 7.5 GHz
-15
dB
7.5 - 15 GHz
-5
dB
0.05 - 5 GHz
-10
dB
100
Ω
RLTX-DIFF
TX Differential return loss
RLTX-CM
TX Common mode return loss
ZTX-DIFF-DC
DC differential TX impedance
VTX-CM-AC-PP
TX AC common mode voltage
VOD = 1.0 Vp-p,
DEM0 = 1, DEM1 = 0
Transmitter short circuit current limit
Total current the transmitter can
supply when shorted to VDD or
GND
ITX-SHORT
VTX-CM-DCACTIVE-IDLE-DELTA
VTX-CM-DC-LINEDELTA
(1)
35
45
ps
0.1
100
UI
mVp-p
20
mA
Absolute delta of DC common mode
voltage during L0 and electrical idle
100
mV
Absolute delta of DC common mode
voltgae between TX+ and TX-
25
mV
In PCIe GEN3 mode, the output VOD level is not fixed. It will be adjusted automatically based on the VID input amplitude level. The
output VOD level set by DEMA/B[1:0] in this MODE is dependent on the VID level and the frequency content. The DS125BR401
repeater is designed to be transparent in this MODE, so the TX-FIR (de-emphasis) is passed to the RX to support the handshake
negotiation link training.
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
7
DS125BR401
SNLS419C – JULY 2012 – REVISED APRIL 2013
www.ti.com
Electrical Characteristics (continued)
Parameter
Test Conditions
Min
Typ
Max
Unit
TTX-IDLE-DATA
Max time to transition to valid
differential signal after idle
VID = 1.0 Vp-p, 8 Gbps
3.5
ns
TTX-DATA-IDLE
Max time to transition to idle after
differential signal
VID = 1.0 Vp-p, 8 Gbps
6.2
ns
(2)
TPDEQ
Differential propagation delay
EQ = 00
200
ps
TLSK
Lane to lane skew
T = 25C, VDD = 2.5V
25
ps
TPPSK
Part to part propagation delay skew
T = 25C, VDD = 2.5V
40
ps
Residual deterministic jitter at 12 Gbps
30” 5mils FR4,
VID = 0.6 Vp-p,
PRBS15, EQ = 07'h,
DEM = 0 dB
0.18
UI
Residual deterministic jitter at 8 Gbps
30” 5mils FR4,
VID = 0.6 Vp-p,
PRBS15, EQ = 07'h,
DEM = 0 dB
0.11
UI
Residual deterministic jitter at 5 Gbps
30” 5mils FR4,
VID = 0.6 Vp-p,
PRBS15, EQ = 07'h,
DEM = 0 dB
0.07
UI
Residual deterministic jitter at 12 Gbps
5 meters 30 awg cable,
VID = 0.6 Vp-p,
PRBS15, EQ = 07'h,
DEM = 0 dB
0.25
UI
Residual deterministic jitter at 12 Gbps
8 meters 30 awg cable,
VID = 0.6 Vp-p,
PRBS15, EQ = 0F'h,
DEM = 0 dB
0.33
UI
Input Channel: 20" 5mils FR4,
Output Channel: 10” 5mils FR4,
VID = 0.6 Vp-p,
PRBS15, EQ = 03'h,
VOD = 1.0 Vp-p,
DEM = −3.5 dB
0.1
UI
Equalization
DJE1
DJE2
DJE3
DJE4
DJE5
De-emphasis (GEN 1&2 mode only)
DJD1
Residual deterministic jitter at 12 Gbps
(2)
8
Propagation Delay measurements will change slightly based on the level of EQ selected. EQ = 00 will result in the shortest propagation
delays.
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
DS125BR401
www.ti.com
SNLS419C – JULY 2012 – REVISED APRIL 2013
Electrical Characteristics — Serial Management Bus Interface
Over recommended operating supply and temperature ranges unless other specified.
Parameter
Test Conditions
Min
Typ
Max
Unit
0.8
V
3.6
V
SERIAL BUS INTERFACE DC SPECIFICATIONS
VIL
Data, Clock Input Low Voltage
VIH
Data, Clock Input High Voltage
IPULLUP
Current Through Pull-Up Resistor
or Current Source
VDD
Nominal Bus Voltage
ILEAK-Bus
Input Leakage Per Bus Segment
ILEAK-Pin
Input Leakage Per Device Pin
CI
Capacitance for SDA and SCL
See (1) (2)
RTERM
External Termination Resistance
pull to VDD = 2.5V ± 5% OR 3.3V ±
10%
Pullup VDD = 3.3V (1) (2) (3)
2000
Ω
Pullup VDD = 2.5V (1) (2) (3)
1000
Ω
2.1
High Power Specification
See (1)
4
mA
2.375
3.6
V
-200
+200
µA
-15
µA
10
pF
SERIAL BUS INTERFACE TIMING SPECIFICATIONS
FSMB
Bus Operating Frequency
ENSMB = VDD (Slave Mode)
TBUF
Bus Free Time Between Stop and
Start Condition
THD:STA
Hold time after (Repeated) Start
Condition. After this period, the first
clock is generated.
ENSMB = FLOAT (Master Mode)
280
400
400
kHz
520
kHz
1.3
µs
0.6
µs
At IPULLUP, Max
TSU:STA
Repeated Start Condition Setup
Time
0.6
µs
TSU:STO
Stop Condition Setup Time
0.6
µs
THD:DAT
Data Hold Time
0
ns
TSU:DAT
Data Setup Time
100
ns
TLOW
Clock Low Period
THIGH
Clock High Period
See (4)
tF
Clock/Data Fall Time
1.3
µs
See (4)
300
ns
(4)
300
ns
500
ms
Clock/Data Rise Time
See
tPOR
Time in which a device must be
operational after power-on reset
See (4) (5)
(1)
(2)
(3)
(4)
(5)
µs
50
tR
0.6
Recommended value.
Recommended maximum capacitance load per bus segment is 400pF.
Maximum termination voltage should be identical to the device supply voltage.
Compliant to SMBus 2.0 physical layer specification. See System Management Bus (SMBus) Specification Version 2.0, section 3.1.1
SMBus common AC specifications for details.
ensured by Design. Parameter not tested in production.
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
9
DS125BR401
SNLS419C – JULY 2012 – REVISED APRIL 2013
www.ti.com
TIMING DIAGRAMS
(OUT+)
80%
80%
VOD (p-p) = (OUT+) ± (OUT-)
0V
20%
20%
(OUT-)
tRISE
tFALL
Figure 1. CML Output and Rise and FALL Transition Time
+
IN
0V
tPLHD
tPHLD
+
OUT
0V
-
Figure 2. Propagation Delay Timing Diagram
+
IN
0V
DATA
tIDLE-DATA
tDATA-IDLE
+
OUT
0V
DATA
IDLE
IDLE
Figure 3. Transmit IDLE-DATA and DATA-IDLE Response Time
tLOW
tR
tHIGH
SCL
tHD:STA
tBUF
tHD:DAT
tF
tSU:STA
tSU:DAT
tSU:STO
SDA
SP
ST
SP
ST
Figure 4. SMBus Timing Parameters
10
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
DS125BR401
www.ti.com
SNLS419C – JULY 2012 – REVISED APRIL 2013
FUNCTIONAL DESCRIPTION
The DS125BR401 compensates for lossy FR-4 printed circuit board backplanes and balanced cables. The
DS125BR401 operates in 3 modes: Pin Control Mode (ENSMB = 0), SMBus Slave Mode (ENSMB = 1) and
SMBus Master Mode (ENSMB = float) to load register informations from external EEPROM; please refer to
SMBUS Master Mode for additional information.
Pin Control Mode:
When in pin mode (ENSMB = 0), equalization and de-emphasis can be selected via pin for each side
independently. When de-emphasis is asserted VOD is automatically adjusted per Table 3. For PCIe applications,
the RXDET pins provides automatic and manual control for input termination (50Ω or >50KΩ). MODE setting is
also pin controllable with pin selections (Gen 1/2, auto detect and PCIe Gen 3). The receiver electrical idle detect
threshold is also adjustable via the SD_TH pin.
SMBUS Mode:
When in SMBus mode (ENSMB = 1), the VOD (output amplitude), equalization, de-emphasis, and termination
disable features are all programmable on a individual lane basis, instead of grouped by A or B as in the pin mode
case. Upon assertion of ENSMB, the EQx and DEMx functions revert to register control immediately. The EQx
and DEMx pins are converted to AD0-AD3 SMBus address inputs. The other external control pins (MODE,
RXDET and SD_TH) remain active unless their respective registers are written to and the appropriate override bit
is set, in which case they are ignored until ENSMB is driven low (pin mode). On power-up and when ENSMB is
driven low all registers are reset to their default state. If PWDN is asserted while ENSMB is high, the registers
retain their current state.
Equalization settings accessible via the pin controls were chosen to meet the needs of most high speed
applications. If additional fine tuning or adjustment is needed, additional equalization settings can be accessed
via the SMBus registers. Each input has a total of 256 possible equalization settings. The tables show the 16
setting when the device is in pin mode. When using SMBus mode, the equalization, VOD and de- Emphasis
levels are set by registers.
The 4-level input pins utilize a resistor divider to help set the 4 valid levels and provide a wider range of control
settings when ENSMB=0. There is an internal 30K pull-up and a 60K pull-down connected to the package pin.
These resistors, together with the external resistor connection combine to achieve the desired voltage level.
Using the 1K pull-up, 1K pull-down, no connect, and 20K pull-down provide the optimal voltage levels for each of
the four input states.
Table 1. 4–Level Control Pin Settings
Level
Setting
3.3V Mode
2.5V Mode
0
Tie 1kΩ to GND
0.10 V
0.08 V
R
Tie 20kΩ to GND
1/3 x VIN
1/3 x VDD
Float
Float (leave pin open)
2/3 x VIN
2/3 x VDD
1
Tie 1kΩ to VIN or VDD
VIN - 0.05 V
VDD - 0.04 V
Typical 4-Level Input Thresholds
• Level 1 - 2 = 0.2 * VIN or VDD
• Level 2 - 3 = 0.5 * VIN or VDD
• Level 3 - 4 = 0.8 * VIN or VDD
In order to minimize the startup current associated with the integrated 2.5V regulator the 1K pull-up / pull-down
resistors are recommended. If several 4 level inputs require the same setting, it is possible to combine two or
more 1K resistors into a single lower value resistor. As an example; combining two inputs with a single 500 Ohm
resistor is a good way to save board space.
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
11
DS125BR401
SNLS419C – JULY 2012 – REVISED APRIL 2013
www.ti.com
3.3V or 2.5V Supply Mode Operation
The DS125BR401 has an optional internal voltage regulator to provide the 2.5V supply to the device. In 3.3V
mode operation, the VIN pin = 3.3V is used to supply power to the device. The internal regulator will provide the
2.5V to the VDD pins of the device and a 0.1 uF cap is needed at each of the 5 VDD pins for power supply decoupling (total capacitance should be ≤0.5 uF), and the VDD pins should be left open. The VDD_SEL pin must
be tied to GND to enable the internal regulator. In 2.5V mode operation, the VIN pin should be left open and 2.5V
supply must be applied to the 5 VDD pins to power the device. The VDD_SEL pin must be left open (no connect)
to disable the internal regulator.
3.3V mode
2.5V mode
VDD_SEL
Enable
VDD_SEL
open
VIN
open
Disable
3.3V
Capacitors can be
either tantalum or an
ultra-low ESR seramic.
Internal
voltage
regulator
2.5V
0.1 uF
0.1 uF
VDD
VDD
0.1 uF
0.1 uF
1 uF
VDD
VDD
10 uF
2.5V
1 uF
VIN
10 uF
Internal
voltage
regulator
Capacitors can be
either tantalum or an
ultra-low ESR seramic.
VDD
VDD
0.1 uF
0.1 uF
VDD
VDD
0.1 uF
0.1 uF
VDD
VDD
0.1 uF
0.1 uF
Place 0.1 uF close to VDD Pin
Total capacitance should be 7 0.5 uF
Place capcitors close to VDD Pin
Figure 5. 3.3V or 2.5V Supply Connection Diagram
PCIe Signal Integrity
When using the DS125BR401 in PCIe GEN-3 systems, there are specific signal integrity settings to ensure
signal integrity margin. The settings were optimized by extensive testing. Please contact your field representative
for more information regarding the testing completed to achieve these settings.
For tuning the in the downstream direction (from CPU to EP).
• EQ: use the guidelines outlined in Table 2.
• De-Emphasis: use the guidelines outlined in Table 3.
• VOD: use the guidelines outlined in Table 3.
For tuning in the upstream direction (from EP to CPU).
• EQ: use the guidelines outlined in Table 2.
• De-Emphasis:
– For trace lengths < 15in set to -3.5 dB
– For trace lengths > 15in set to -6 dB
• VOD: set to 900 mV
12
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
DS125BR401
www.ti.com
SNLS419C – JULY 2012 – REVISED APRIL 2013
Table 2. Equalizer Settings
Level
EQA1
EQB1
EQA0
EQB
EQ – 8 bits [7:0]
dB at
1.5 GHz
dB at
2.5 GHz
dB at
4 GHz
dB at
6 GHz
Suggested Use (1)
1
0
0
0000 0000 = 0x00
2.5
3.5
3.8
3.1
FR4 < 5 inch trace
2
0
R
0000 0001 = 0x01
3.8
5.4
6.7
6.7
FR4 5-10 inch trace
3
0
Float
0000 0010 = 0x02
5.0
7.0
8.4
8.4
FR4 10 inch trace
4
0
1
0000 0011 = 0x03
5.9
8.0
9.3
9.1
FR4 15-20 inch trace
5
R
0
0000 0111 = 0x07
7.4
10.3
12.8
13.7
FR4 20-30 inch trace
6
R
R
0001 0101 = 0x15
6.9
10.2
13.9
16.2
FR4 25-30 inch trace
7
R
Float
0000 1011 = 0x0B
9.0
12.4
15.3
15.9
FR4 25-30 inch trace
8
R
1
0000 1111 = 0x0F
10.2
13.8
16.7
17.0
8m, 30awg cable
9
Float
0
0101 0101 = 0x55
8.5
12.6
17.5
20.7
> 8m cable
10
Float
R
0001 1111 = 0x1F
11.7
16.2
20.3
21.8
11
Float
Float
0010 1111 = 0x2F
13.2
18.3
22.8
23.6
12
Float
1
0011 1111 = 0x3F
14.4
19.8
24.2
24.7
13
1
0
1010 1010 = 0xAA
14.4
20.5
26.4
28.0
14
1
R
0111 1111 = 0x7F
16.0
22.2
27.8
29.2
15
1
Float
1011 1111 = 0xBF
17.6
24.4
30.2
30.9
16
1
1
1111 1111 = 0xFF
18.7
25.8
31.6
31.9
(1)
Cable and FR4 lengths are for reference only. FR4 lengths based on a 100 Ohm differential stripline with 5-mil traces and 8-mil trace
separation. Optimal EQ setting should be determined via simulation and prototype verification.
Table 3. Output Voltage and De-emphasis Settings
(1)
(2)
Level
DEMA1
DEMB1
DEMA0
DEMB0
VOD Vp-p
DEM dB (1)
Inner Amplitude
Vp-p
Suggested Use (2)
1
0
0
0.8
0
0.8
FR4 <5 inch trace
2
0
R
0.9
0
0.9
FR4 <5 inch trace
3
0
Float
0.9
- 3.5
0.6
FR4 10 inch trace
4
0
1
1.0
0
1.0
FR4 <5 inch trace
5
R
0
1.0
- 3.5
0.7
FR4 10 inch trace
6
R
R
1.0
-6
0.5
FR4 15 inch trace
7
R
Float
1.1
0
1.1
FR4 <5 inch trace
8
R
1
1.1
- 3.5
0.7
FR4 10 inch trace
9
Float
0
1.1
-6
0.6
FR4 15 inch trace
10
Float
R
1.2
0
1.2
FR4 <5 inch trace
11
Float
Float
1.2
- 3.5
0.8
FR4 10 inch trace
12
Float
1
1.2
-6
0.6
FR4 15 inch trace
13
1
0
1.3
0
1.3
FR4 <5 inch trace
14
1
R
1.3
- 3.5
0.9
FR4 10 inch trace
15
1
Float
1.3
-6
0.7
FR4 15 inch trace
16
1
1
1.3
-9
0.5
FR4 20 inch trace
The VOD output amplitude and DEM de-emphasis levels are set with the DEMA/B[1:0] pins.
The de-emphasis levels are also available in PCIe GEN-3 mode when MODE = 1 (tied to VDD).
FR4 lengths are for reference only. FR4 lengths based on a 100 Ohm differential stripline with 5-mil traces and 8-mil trace separation.
Optimal DEM settings should be determined via simulation and prototype verification.
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
13
DS125BR401
SNLS419C – JULY 2012 – REVISED APRIL 2013
www.ti.com
Table 4. RX-Detect Settings
PWDN
(PIN 52)
RXDET
(PIN 22)
SMBus REG
bit[3:2]
Input Termination
Recommeded
Use
0
0
00
Hi-Z
X
Comments
Manual RX-Detect, input is high impedance mode
0
Tie 20kΩ
to GND
01
Pre Detect: Hi-Z
Post Detect: 50 Ω
PCIe only
Auto RX-Detect, outputs test every 12 msec for 600
msec then stops; termination is Hi-Z until RX
detection; once detected input termination is 50 Ω
Reset function by pulsing PWDN high for 5 usec
then low again
0
Float
(Default)
10
Pre Detect: Hi-Z
Post Detect: 50 Ω
PCIe only
Auto RX-Detect, outputs test every 12 msec until
detection occurs; termination is Hi-Z until RX
detection; once detected input termination is 50 Ω
0
1
11
50 Ω
All Others
Manual RX-Detect, input is 50 Ω
1
X
High Impedance
Power down mode, input is Hi-Z, output drivers are
disabled
Used to reset RX-Detect State Machine when held
high for 5 usec
X
RX-Detect in SAS/SATA (up to 6 Gbps) Applications
Unlike PCIe systems, SAS/SATA (up to 6 Gbps) systems use a low speed Out-Of-Band or OOB communications
sequence to detect and communicate between Controllers/Expanders and target drives. This communication
eliminates the need to detect for endpoints like PCIe. For SAS/SATA systems, it is recommended to tie the
RXDET pin high. This will ensure any OOB sequences sent from the Controller/Expander will reach the target
drive without any additional latency due to the termination detection sequence defined by PCIe.
Table 5. Signal Detect Threshold Level (1)
(1)
SD_TH (PIN 26)
SMBus REG bit [3:2] and [1:0]
Assert Level (typ)
De-assert Level (typ)
0
10
210 mVp-p
150 mVp-p
R
01
160 mVp-p
100 mVp-p
F (default)
00
180 mVp-p
110 mVp-p
1
11
190 mVp-p
130 mVp-p
VDD = 2.5V, 25°C and 0101 pattern at 8 Gbps
Table 6. MODE operation with Pin Control
MODE
(PIN 21)
Driver Characteristics
0
Limiting
R
Transparent without DE
F (default)
Automatic
1
Transparent with DE
PCIe
SAS
SATA
10G-KR
X
10GbE
CPRI
OBSAI
SRIO
(R)XAUI
Interlaken
Infiniband
X
X
X
X
X
X
Note: Automatic operation allows input to sense the incoming data-rate and utilize a "Transparent" output driver
for operation at or above 8 Gbps.
Note: SAS/SATA up to 6 Gbps.
MODE operation with SMBus Registers
When in SMBus mode (Slave or Master), the MODE pin retains control of the output driver characteristics. In
order to override this control function, Register 0x08[2] must be written with a "1". Writting this bit enables MODE
control of each channel individually using the channel registers defined in Table 7.
14
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
DS125BR401
www.ti.com
SNLS419C – JULY 2012 – REVISED APRIL 2013
SMBUS Master Mode
The DS125BR401 device supports reading directly from an external EEPROM device by implementing SMBus
Master mode. When using the SMBus master mode, the DS125BR401 will read directly from specific location in
the external EEPROM. When designing a system for using the external EEPROM, the user needs to follow these
specific guidelines.
• Set ENSMB = Float — enable the SMBUS master mode.
• The external EEPROM device address byte must be 0xA0'h and capable of 400 kHz operation at 2.5V and
3.3V supply.
• Set the AD[3:0] inputs for SMBus address byte. When the AD[3:0] = 0000'b, the device address byte is B0'h.
When tying multiple DS125BR401 devices to the SDA and SCL bus, use these guidelines to configure the
devices.
• Use SMBus AD[3:0] address bits so that each device can loaded it's configuration from the EEPROM.
Example below is for 4 device.
– U1: AD[3:0] = 0000 = 0xB0'h,
– U2: AD[3:0] = 0001 = 0xB2'h,
– U3: AD[3:0] = 0010 = 0xB4'h,
– U4: AD[3:0] = 0011 = 0xB6'h
• Use a pull-up resistor on SDA and SCL; value = 2k ohms
• Daisy-chain READEN# (pin 26) and ALL_DONE# (pin 27) from one device to the next device in the sequence
so that they do not compete for the EEPROM at the same time.
1. Tie READEN# of the 1st device in the chain (U1) to GND
2. Tie ALL_DONE# of U1 to READEN# of U2
3. Tie ALL_DONE# of U2 to READEN# of U3
4. Tie ALL_DONE# of U3 to READEN# of U4
5. Optional: Tie ALL_DONE# output of U4 to a LED to show the devices have been loaded successfully
Below is an example of a 2 kbits (256 x 8-bit) EEPROM in hex format for the DS125BR401 device. The first 3
bytes of the EEPROM always contain a header common and necessary to control initialization of all devices
connected to the I2C bus. CRC enable flag to enable/disable CRC checking. If CRC checking is disabled, a fixed
pattern (8’hA5) is written/read instead of the CRC byte from the CRC location, to simplify the control. There is a
MAP bit to flag the presence of an address map that specifies the configuration data start in the EEPROM. If the
MAP bit is not present the configuration data start address is derived from the DS125BR401 address and the
configuration data size. A bit to indicate an EEPROM size > 256 bytes is necessary to properly address the
EEPROM. There are 37 bytes of data size for each DS125BR401 device.
:2000000000001000000407002FAD4002FAD4002FAD4002FAD401805F5A8005F5A8005F5AD8
:200020008005F5A800005454000000000000000000000000000000000000000000000000F6
:20006000000000000000000000000000000000000000000000000000000000000000000080
:20008000000000000000000000000000000000000000000000000000000000000000000060
:2000A000000000000000000000000000000000000000000000000000000000000000000040
:2000C000000000000000000000000000000000000000000000000000000000000000000020
:2000E000000000000000000000000000000000000000000000000000000000000000000000
:200040000000000000000000000000000000000000000000000000000000000000000000A0
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
15
DS125BR401
SNLS419C – JULY 2012 – REVISED APRIL 2013
www.ti.com
Table 7. EEPROM Register Map - Single Device with Default Value
EEPROM Address
Byte
Description
0
Value
Description
1
Value
Description
2
Value
Description
3
Value
Description
4
Value
Description
5
Value
Description
6
Value
Description
7
Value
Description
8
Value
Description
9
Value
Description
10
Value
Description
11
Value
Description
12
Value
Description
13
Value
Description
14
Value
Description
Value
16
15
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
BIt 0
CRC EN
Address Map
Present
EEPROM > 256
Bytes
RES
DEVICE
COUNT[3]
DEVICE
COUNT[2]
DEVICE
COUNT[1]
DEVICE
COUNT[0]
0
0
0
0
0
0
0
0
RES
RES
RES
RES
RES
RES
RES
RES
0
0
0
0
0
0
0
0
Max EEPROM
Burst size[7]
Max EEPROM
Burst size[6]
Max EEPROM
Burst size[5]
Max EEPROM
Burst size[4]
Max EEPROM
Burst size[3]
Max EEPROM
Burst size[2]
Max EEPROM
Burst size[1]
Max EEPROM
Burst size[0]
0
0
0
0
0
0
0
0
PWDN_ch7
PWDN_ch6
PWDN_ch5
PWDN_ch4
PWDN_ch3
PWDN_ch2
PWDN_ch1
PWDN_ch0
0
0
0
0
0
0
0
0
lpbk_1
lpbk_0
PWDN_INPUTS
PWDN_OSC
Ovrd_PWDN
RES
RES
RES
0
0
0
0
0
0
0
0
RES
RES
RES
RES
RES
rxdet_btb_en
Ovrd_idle_th
Ovrd_RES
0
0
0
0
0
1
0
0
Ovrd_IDLE
Ovrd_RX_DET
Ovrd_MODE
Ovrd_RES
Ovrd_RES
rx_delay_sel_2
rx_delay_sel_1
rx_delay_sel_0
0
0
0
0
0
1
1
1
RD_delay_sel_3
RD_delay_sel_2
RD_delay_sel_1
RD_delay_sel_0
ch0_Idle_auto
ch0_Idle_sel
ch0_RXDET_1
ch0_RXDET_0
0
0
0
0
0
0
0
0
ch0_BST_7
ch0_BST_6
ch0_BST_5
ch0_BST_4
ch0_BST_3
ch0_BST_2
ch0_BST_1
ch0_BST_0
0
0
1
0
1
1
1
1
ch0_Sel_scp
ch0_Sel_mode
ch0_RES_2
ch0_RES_1
ch0_RES_0
ch0_VOD_2
ch0_VOD_1
ch0_VOD_0
1
0
1
0
1
1
0
1
ch0_DEM_2
ch0_DEM_1
ch0_DEM_0
ch0_Slow
ch0_idle_tha_1
ch0_idle_tha_0
ch0_idle_thd_1
ch0_idle_thd_0
0
1
0
0
0
0
0
0
ch1_Idle_auto
ch1_Idle_sel
ch1_RXDET_1
ch1_RXDET_0
ch1_BST_7
ch1_BST_6
ch1_BST_5
ch1_BST_4
0
0
0
0
0
0
1
0
ch1_BST_3
ch1_BST_2
ch1_BST_1
ch1_BST_0
ch1_Sel_scp
ch1_Sel_mode
ch1_RES_2
ch1_RES_1
1
1
1
1
1
0
1
0
ch1_RES_0
ch1_VOD_2
ch1_VOD_1
ch1_VOD_0
ch1_DEM_2
ch1_DEM_1
ch1_DEM_0
ch1_Slow
1
1
0
1
0
1
0
0
ch1_idle_tha_1
ch1_idle_tha_0
ch1_idle_thd_1
ch1_idle_thd_0
ch2_Idle_auto
ch2_Idle_sel
ch2_RXDET_1
ch2_RXDET_0
0
0
0
0
0
0
0
0
ch2_BST_7
ch2_BST_6
ch2_BST_5
ch2_BST_4
ch2_BST_3
ch2_BST_2
ch2_BST_1
ch2_BST_0
0
0
1
0
1
1
1
1
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
DS125BR401
www.ti.com
SNLS419C – JULY 2012 – REVISED APRIL 2013
Table 7. EEPROM Register Map - Single Device with Default Value (continued)
EEPROM Address
Byte
Description
16
Value
Description
17
Value
Description
18
Value
Description
19
Value
Description
20
Value
Description
21
Value
Description
22
Value
Description
23
Value
Description
24
Value
Description
25
Value
Description
26
Value
Description
27
Value
Description
28
Value
Description
29
Value
Description
30
Value
Description
Value
31
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
BIt 0
ch2_Sel_scp
ch2_Sel_mode
ch2_RES_2
ch2_RES_1
ch2_RES_0
ch2_VOD_2
ch2_VOD_1
ch2_VOD_0
1
0
1
0
1
1
0
1
ch2_DEM_2
ch2_DEM_1
ch2_DEM_0
ch2_Slow
ch2_idle_tha_1
ch2_idle_tha_0
ch2_idle_thd_1
ch2_idle_thd_0
0
1
0
0
0
0
0
0
ch3_Idle_auto
ch3_Idle_sel
ch3_RXDET_1
ch3_RXDET_0
ch3_BST_7
ch3_BST_6
ch3_BST_5
ch3_BST_4
0
0
0
0
0
0
1
0
ch3_BST_3
ch3_BST_2
ch3_BST_1
ch3_BST_0
ch3_Sel_scp
ch3_Sel_mode
ch3_RES_2
ch3_RES_1
1
1
1
1
1
0
1
0
ch3_RES_0
ch3_VOD_2
ch3_VOD_1
ch3_VOD_0
ch3_DEM_2
ch3_DEM_1
ch3_DEM_0
ch3_Slow
1
1
0
1
0
1
0
0
ch3_idle_tha_1
ch3_idle_tha_0
ch3_idle_thd_1
ch3_idle_thd_0
ovrd_fast_idle
en_high_idle_th_n
en_high_idle_th_s
en_fast_idle_n
0
0
0
0
0
0
0
1
en_fast_idle_s
eqsd_mgain_n
eqsd_mgain_s
ch4_Idle_auto
ch4_Idle_sel
ch4_RXDET_1
ch4_RXDET_0
ch4_BST_7
1
0
0
0
0
0
0
0
ch4_BST_6
ch4_BST_5
ch4_BST_4
ch4_BST_3
ch4_BST_2
ch4_BST_1
ch4_BST_0
ch4_Sel_scp
0
1
0
1
1
1
1
1
ch4_Sel_mode
ch4_RES_2
ch4_RES_1
ch4_RES_0
ch4_VOD_2
ch4_VOD_1
ch4_VOD_0
ch4_DEM_2
0
1
0
1
1
0
1
0
ch4_DEM_1
ch4_DEM_0
ch4_Slow
ch4_idle_tha_1
ch4_idle_tha_0
ch4_idle_thd_1
ch4_idle_thd_0
ch5_Idle_auto
1
0
0
0
0
0
0
0
ch5_Idle_sel
ch5_RXDET_1
ch5_RXDET_0
ch5_BST_7
ch5_BST_6
ch5_BST_5
ch5_BST_4
ch5_BST_3
0
0
0
0
0
1
0
1
ch5_BST_2
ch5_BST_1
ch5_BST_0
ch5_Sel_scp
ch5_Sel_mode
ch5_RES_2
ch5_RES_1
ch5_RES_0
1
1
1
1
0
1
0
1
ch5_VOD_2
ch5_VOD_1
ch5_VOD_0
ch5_DEM_2
ch5_DEM_1
ch5_DEM_0
ch5_Slow
ch5_idle_tha_1
1
0
1
0
1
0
0
0
ch5_idle_tha_0
ch5_idle_thd_1
ch5_idle_thd_0
ch6_Idle_auto
ch6_Idle_sel
ch6_RXDET_1
ch6_RXDET_0
ch6_BST_7
0
0
0
0
0
0
0
0
ch6_BST_6
ch6_BST_5
ch6_BST_4
ch6_BST_3
ch6_BST_2
ch6_BST_1
ch6_BST_0
ch6_Sel_scp
0
1
0
1
1
1
1
1
ch6_Sel_mode
ch6_RES_2
ch6_RES_1
ch6_RES_0
ch6_VOD_2
ch6_VOD_1
ch6_VOD_0
ch6_DEM_2
0
1
0
1
1
0
1
0
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
17
DS125BR401
SNLS419C – JULY 2012 – REVISED APRIL 2013
www.ti.com
Table 7. EEPROM Register Map - Single Device with Default Value (continued)
EEPROM Address
Byte
Description
32
Value
Description
33
Value
Description
34
Value
Description
35
Value
Description
36
Value
Description
37
Value
Description
38
Value
Description
Value
18
39
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
ch6_DEM_1
ch6_DEM_0
ch6_Slow
ch6_idle_tha_1
ch6_idle_tha_0
ch6_idle_thd_1
ch6_idle_thd_0
ch7_Idle_auto
1
0
0
0
0
0
0
0
ch7_Idle_sel
ch7_RXDET_1
ch7_RXDET_0
ch7_BST_7
ch7_BST_6
ch7_BST_5
ch7_BST_4
ch7_BST_3
0
0
0
0
0
1
0
1
ch7_BST_2
ch7_BST_1
ch7_BST_0
ch7_Sel_scp
ch7_Sel_mode
ch7_RES_2
ch7_RES_1
ch7_RES_0
1
1
1
1
0
1
0
1
ch7_VOD_2
ch7_VOD_1
ch7_VOD_0
ch7_DEM_2
ch7_DEM_1
ch7_DEM_0
ch7_Slow
ch7_idle_tha_1
1
0
1
0
1
0
0
0
ch7_idle_tha_0
ch7_idle_thd_1
ch7_idle_thd_0
iph_dac_ns_1
iph_dac_ns_0
ipp_dac_ns_1
ipp_dac_ns_0
ipp_dac_1
0
0
0
0
0
0
0
0
ipp_dac_0
RD23_67
RD01_45
RD_PD_ovrd
RD_Sel_test
RD_RESET_ovrd
PWDB_input_DC
DEM_VOD_ovrd
0
0
0
0
0
0
0
0
DEM_ovrd_N2
DEM_ovrd_N1
DEM_ovrd_N0
VOD_ovrd_N2
VOD_ovrd_N1
VOD_ovrd_N0
SPARE0
SPARE1
0
1
0
1
0
1
0
0
DEM__ovrd_S2
DEM__ovrd_S1
DEM_ovrd_S0
VOD_ovrd_S2
VOD_ovrd_S1
VOD_ovrd_S0
SPARE0
SPARE1
0
1
0
1
0
1
0
0
Submit Documentation Feedback
Bit 2
Bit 1
BIt 0
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
DS125BR401
www.ti.com
SNLS419C – JULY 2012 – REVISED APRIL 2013
Table 8. Example of EEPROM for four Devices Using Two Address Maps
EEPROM
Address
Address (Hex)
EEPROM Data
0
00
0x43
1
01
0x00
2
02
0x08
EEPROM Burst Size
3
03
0x00
CRC not used
4
04
0x0B
Device 0 Address Location
5
05
0x00
CRC not used
6
06
0x0B
Device 1 Address Location
7
07
0x00
CRC not used
8
08
0x30
Device 2 Address Location
9
09
0x00
CRC not used
10
0A
0x30
Device 3 Address Location
11
0B
0x00
Begin Device 0, 1 - Address Offset 3
12
0C
0x00
13
0D
0x04
14
0E
0x07
15
0F
0x00
16
10
0x00
EQ CHB0 = 00
17
11
0xAB
VOD CHB0 = 1.0V
18
12
0x00
DEM CHB0 = 0 (0dB)
19
13
0x00
EQ CHB1 = 00
20
14
0x0A
VOD CHB1 = 1.0V
21
15
0xB0
DEM CHB1 = 0 (0dB)
22
16
0x00
23
17
0x00
EQ CHB2 = 00
24
18
0xAB
VOD CHB2 = 1.0V
25
19
0x00
DEM CHB2 = 0 (0dB)
26
1A
0x00
EQ CHB3 = 00
27
1B
0x0A
VOD CHB3 = 1.0V
28
1C
0xB0
DEM CHB3 = 0 (0dB)
29
1D
0x01
30
1E
0x80
31
1F
0x01
EQ CHA0 = 00
32
20
0x56
VOD CHA0 = 1.0V
33
21
0x00
DEM CHA0 = 0 (0dB)
34
22
0x00
EQ CHA1 = 00
35
23
0x15
VOD CHA1 = 1.0V
36
24
0x60
DEM CHA1 = 0 (0dB)
37
25
0x00
38
26
0x01
EQ CHA2 = 00
39
27
0x56
VOD CHA2 = 1.0V
40
28
0x00
DEM CHA2 = 0 (0dB)
41
29
0x00
EQ CHA3 = 00
42
2A
0x15
VOD CHA3 = 1.0V
43
2B
0x60
DEM CHA3 = 0 (0dB)
44
2C
0x00
45
2D
0x00
46
2E
0x54
Comments
CRC_EN = 0, Address Map = 1, >256 bytes = 0, Device Count[3:0] = 3
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
19
DS125BR401
SNLS419C – JULY 2012 – REVISED APRIL 2013
www.ti.com
Table 8. Example of EEPROM for four Devices Using Two Address Maps (continued)
EEPROM
Address
Address (Hex)
EEPROM Data
47
2F
0x54
End Device 0, 1 - Address Offset 39
48
30
0x00
Begin Device 2, 3 - Address Offset 3
49
31
0x00
50
32
0x04
51
33
0x07
52
34
0x00
53
35
0x00
EQ CHB0 = 00
54
36
0xAB
VOD CHB0 = 1.0V
55
37
0x00
DEM CHB0 = 0 (0dB)
56
38
0x00
EQ CHB1 = 00
57
39
0x0A
VOD CHB1 = 1.0V
58
3A
0xB0
DEM CHB1 = 0 (0dB)
59
3B
0x00
60
3C
0x00
EQ CHB2 = 00
61
3D
0xAB
VOD CHB2 = 1.0V
62
3E
0x00
DEM CHB2 = 0 (0dB)
63
3F
0x00
EQ CHB3 = 00
64
40
0x0A
VOD CHB3 = 1.0V
65
41
0xB0
DEM CHB3 = 0 (0dB)
66
42
0x01
67
43
0x80
68
44
0x01
EQ CHA0 = 00
69
45
0x56
VOD CHA0 = 1.0V
70
46
0x00
DEM CHA0 = 0 (0dB)
71
47
0x00
EQ CHA1 = 00
72
48
0x15
VOD CHA1 = 1.0V
73
49
0x60
DEM CHA1 = 0 (0dB)
74
4A
0x00
75
4B
0x01
EQ CHA2 = 00
76
4C
0x56
VOD CHA2 = 1.0V
77
4D
0x00
DEM CHA2 = 0 (0dB)
78
4E
0x00
EQ CHA3 = 00
79
4F
0x15
VOD CHA3 = 1.0V
80
50
0x60
DEM CHA3 = 0 (0dB)
81
51
0x00
82
52
0x00
83
53
0x54
84
54
0x54
Comments
End Device 2, 3 - Address Offset 39
Note: CRC_EN = 0, Address Map = 1, >256 byte = 0, Device Count[3:0] = 3. This example has all 8–channels
set to EQ = 00 (min boost), VOD = 1.0V, DEM = 0 (0dB) and multiple device can point to the same address map.
20
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
DS125BR401
www.ti.com
SNLS419C – JULY 2012 – REVISED APRIL 2013
System Management Bus (SMBus) and Configuration Registers
The System Management Bus interface is compatible to SMBus 2.0 physical layer specification. ENSMB = 1kΩ
to VDD to enable SMBus slave mode and allow access to the configuration registers.
The DS125BR401 has the AD[3:0] inputs in SMBus mode. These pins are the user set SMBUS slave address
inputs. The AD[3:0] pins have internal pull-down. When left floating or pulled low the AD[3:0] = 0000'b, the device
default address byte is B0'h. Based on the SMBus 2.0 specification, the DS125BR401 has a 7-bit slave address.
The LSB is set to 0'b (for a WRITE). The device supports up to 16 address byte, which can be set with the
AD[3:0] inputs. Below are the 16 addresses.
Table 9. Device Slave Address Bytes
AD[3:0] Settings
Address Bytes (HEX)
0000
B0
0001
B2
0010
B4
0011
B6
0100
B8
0101
BA
0110
BC
0111
BE
1000
C0
1001
C2
1010
C4
1011
C6
1100
C8
1101
CA
1110
CC
1111
CE
The SDA, SCL pins are 3.3V tolerant, but are not 5V tolerant. External pull-up resistor is required on the SDA.
The resistor value can be from 1 kΩ to 5 kΩ depending on the voltage, loading and speed. The SCL may also
require an external pull-up resistor and it depends on the Host that drives the bus.
TRANSFER OF DATA VIA THE SMBus
During normal operation the data on SDA must be stable during the time when SCL is High.
There are three unique states for the SMBus:
START: A High-to-Low transition on SDA while SCL is High indicates a message START condition.
STOP: A Low-to-High transition on SDA while SCL is High indicates a message STOP condition.
IDLE: If SCL and SDA are both High for a time exceeding tBUF from the last detected STOP condition or if they
are High for a total exceeding the maximum specification for tHIGH then the bus will transfer to the IDLE state.
SMBus TRANSACTIONS
The device supports WRITE and READ transactions. See Table 10 for register address, type (Read/Write, Read
Only), default value and function information.
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
21
DS125BR401
SNLS419C – JULY 2012 – REVISED APRIL 2013
www.ti.com
WRITING A REGISTER
To
1.
2.
3.
4.
5.
6.
7.
write a register, the following protocol is used (see SMBus 2.0 specification).
The Host drives a START condition, the 7-bit SMBus address, and a “0” indicating a WRITE.
The Device (Slave) drives the ACK bit (“0”).
The Host drives the 8-bit Register Address.
The Device drives an ACK bit (“0”).
The Host drive the 8-bit data byte.
The Device drives an ACK bit (“0”).
The Host drives a STOP condition.
The WRITE transaction is completed, the bus goes IDLE and communication with other SMBus devices may
now occur.
READING A REGISTER
To read a register, the following protocol is used (see SMBus 2.0 specification).
1. The Host drives a START condition, the 7-bit SMBus address, and a “0” indicating a WRITE.
2. The Device (Slave) drives the ACK bit (“0”).
3. The Host drives the 8-bit Register Address.
4. The Device drives an ACK bit (“0”).
5. The Host drives a START condition.
6. The Host drives the 7-bit SMBus Address, and a “1” indicating a READ.
7. The Device drives an ACK bit “0”.
8. The Device drives the 8-bit data value (register contents).
9. The Host drives a NACK bit “1”indicating end of the READ transfer.
10. The Host drives a STOP condition.
The READ transaction is completed, the bus goes IDLE and communication with other SMBus devices may now
occur.
Table 10 for more information.
Table 10. SMBUS Slave Mode Register Map
Address
0x00
0x01
22
Register Name
Observation
PWDN Channels
Bit
Field
Type
Default
0x00
Description
7
Reserved
R/W
Set bit to 0.
6:3
Address Bit
AD[3:0]
R
Observation of AD[3:0] bits
[6]: AD3
[5]: AD2
[4]: AD1
[3]: AD0
2
EEPROM Read
Done
R
1: Device completed the read from external
EEPROM.
1
Reserved
R/W
Set bit to 0.
0
Reserved
R/W
7:0
PWDN CHx
R/W
Set bit to 0.
0x00
Power Down per Channel
[7]: CH7 – CHA_3
[6]: CH6 – CHA_2
[5]: CH5 – CHA_1
[4]: CH4 – CHA_0
[3]: CH3 – CHB_3
[2]: CH2 – CHB_2
[1]: CH1 – CHB_1
[0]: CH0 – CHB_0
00'h = all channels enabled
FF'h = all channels disabled
Note: override PWDN pin.
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
DS125BR401
www.ti.com
SNLS419C – JULY 2012 – REVISED APRIL 2013
Table 10. SMBUS Slave Mode Register Map (continued)
Address
0x02
Register Name
Override PWDN,
LPBK Control
Bit
Field
Type
R/W
Default
0x00
Description
7:6
Reserved
Set bits to 0.
5:4
LPBK
Control
00:
01:
10:
11:
3:1
Reserved
Set bits to 0.
0
Override PWDN
pin
1: Block PWDN pin control
0: Allow PWDN pin control
Use LPBK pin control
INA_n to OUTB_n loopback
INB_n to OUTA_n loopback
Disable loopback and ignore LPBK pin.
0x05
Slave Mode CRC bits
7:0
CRC bits
R/W
0x00
CRC bits [7:0]
0x06
Slave Register
Control
7:5
Reserved
R/W
0x10
Set bits to 0.
4
Reserved
Set bit to 1.
3
Register Enable
1: Enables high speed channel control via SMBus
registers without CRC
0: Channel control via SMBus registers requires
correct CRC in Reg 0x05
Note: In order to change VOD, DEM and EQ of the
channels in slave mode without also setting CRC
each time, set this bit to 1.
2:0
Reserved
Set bits to 0.
7
Reserved
6
Reset Registers
Self clearing reset for SMBus registers. Writing a [1]
will return register settings to default values.
5
Reset SMBus
Master
Self clearing reset to SMBus master state machine
4:0
Reserved
7
Reserved
6
Override SD_TH
1: Block SD_TH pin control
0: Allow SD_TH pin control
5
Reserved
Set bit to 0.
4
Override IDLE
1: IDLE control by registers
0: IDLE control by signal detect
3
Override RXDET
1: Block RXDET pin control
0: Allow RXDET pin control
2
Override MODE
1: Block MODE pin control
0: Allow MODE pin control
1
Reserved
Set bit to 0.
0
Reserved
Set bit to 0.
7:6
Reserved
5
IDLE_AUTO
1: Automatic IDLE detect
0: Allow IDLE_SEL control in bit 4
Note: override IDLE control.
4
IDLE_SEL
1: Output is MUTED (electrical idle)
0: Output is ON
Note: override IDLE control.
3:2
RXDET
00: Input is high-z impedance
01: Auto RX-Detect,
outputs test every 12 ms for 600 ms (50 times) then
stops; termination is high-z until detection; once
detected input termination is 50 Ω
10: Auto RX-Detect,
outputs test every 12 ms until detection occurs;
termination is high-z until detection; once detected
input termination is 50 Ω
11: Input is 50 Ω
Note: override RXDET pin.
1:0
Reserved
Set bits to 0.
0x07
0x08
0x0E
Digital Reset and
Control
Override
Pin Control
CH0 - CHB0
IDLE, RXDET
R/W
0x01
Set bit to 0.
Set bits to 0 0001'b.
R/W
R/W
0x00
0x00
Set bit to 0.
Set bits to 0.
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
23
DS125BR401
SNLS419C – JULY 2012 – REVISED APRIL 2013
www.ti.com
Table 10. SMBUS Slave Mode Register Map (continued)
Address
Register Name
Bit
Field
Type
Default
Description
0x0F
CH0 - CHB0
EQ
7:0
EQ Control
R/W
0x2F
IB0 EQ Control - total of 256 levels.
See Table 2.
0x10
CH0 - CHB0
VOD
7
Short Circuit
Protection
R/W
0xAD
1: Enable the short circuit protection
0: Disable the short circuit protection
6
MODE_SEL
1: PCIe Gen 1/2,
0: PCIe Gen 3
Note: override the MODE pin.
5:3
Reserved
Set bits to default value - 101.
2:0
VOD Control
OB0 VOD Control
000: 0.7 V
001: 0.8 V
010: 0.9 V
011: 1.0 V
100: 1.1 V
101: 1.2 V (default)
110: 1.3 V
111: 1.4 V
7
RXDET STATUS
R
6:5
MODE_DET
STATUS
R
Observation bit for MODE_DET CH0 - CHB0.
00: GEN1 (2.5G)
01: GEN2 (5G)
11: GEN3 (8G+)
4:3
Reserved
R/W
Set bits to 0.
2:0
DEM Control
R/W
OB0 DEM Control
000: 0 dB
001: –1.5 dB
010: –3.5 dB (default)
011: –5 dB
100: –6 dB
101: –8 dB
110: –9 dB
111: –12 dB
7:4
Reserved
R/W
3:2
IDLE thd
De-assert threshold
00 = 110 mVp-p (default)
01 = 100 mVp-p
10 = 150 mVp-p
11 = 130 mVp-p
Note: override the SD_TH pin.
1:0
IDLE tha
Assert threshold
00 = 180 mVp-p (default)
01 = 160 mVp-p
10 = 210 mVp-p
11 = 190 mVp-p
Note: override the SD_TH pin.
0x11
0x12
24
CH0 - CHB0
DEM
CH0 - CHB0
IDLE Threshold
0x02
0x00
Observation bit for RXDET CH0 - CHB0.
1: RX = detected
0: RX = not detected
Set bits to 0.
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
DS125BR401
www.ti.com
SNLS419C – JULY 2012 – REVISED APRIL 2013
Table 10. SMBUS Slave Mode Register Map (continued)
Address
0x15
Register Name
CH1 - CHB1
IDLE, RXDET
Bit
Field
Type
R/W
Default
0x00
Description
7:6
Reserved
Set bits to 0.
5
IDLE_AUTO
1: Automatic IDLE detect
0: Allow IDLE_SEL control in bit 4
Note: override IDLE control.
4
IDLE_SEL
1: Output is MUTED (electrical idle)
0: Output is ON
Note: override IDLE control.
3:2
RXDET
00: Input is high-z impedance
01: Auto RX-Detect,
outputs test every 12 ms for 600 ms (50 times) then
stops; termination is high-z until detection; once
detected input termination is 50 Ω
10: Auto RX-Detect,
outputs test every 12 ms until detection occurs;
termination is high-z until detection; once detected
input termination is 50 Ω
11: Input is 50 Ω
Note: override RXDET pin.
1:0
Reserved
0x16
CH1 - CHB1
EQ
7:0
EQ Control
R/W
0x2F
IB1 EQ Control - total of 256 levels.
See Table 2.
0x17
CH1 - CHB1
VOD
7
Short Circuit
Protection
R/W
0xAD
1: Enable the short circuit protection
0: Disable the short circuit protection
6
MODE_SEL
1: Gen 1/2,
0: PCIe Gen 3
Note: override the MODE pin.
5:3
Reserved
Set bits to default value - 101.
2:0
VOD Control
OB1 VOD Control
000: 0.7 V
001: 0.8 V
010: 0.9 V
011: 1.0 V
100: 1.1 V
101: 1.2 V (default)
110: 1.3 V
111: 1.4 V
7
RXDET STATUS
R
6:5
MODE_DET
STATUS
R
Observation bit for MODE_DET CH1 - CHB1.
00: GEN1 (2.5G)
01: GEN2 (5G)
11: GEN3 (8G+)
4:3
Reserved
R/W
Set bits to 0.
2:0
DEM Control
R/W
OB1 DEM Control
000: 0 dB
001: –1.5 dB
010: –3.5 dB (default)
011: –5 dB
100: –6 dB
101: –8 dB
110: –9 dB
111: –12 dB
0x18
CH1 - CHB1
DEM
Set bits to 0.
0x02
Observation bit for RXDET CH1 - CHB1.
1: RX = detected
0: RX = not detected
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
25
DS125BR401
SNLS419C – JULY 2012 – REVISED APRIL 2013
www.ti.com
Table 10. SMBUS Slave Mode Register Map (continued)
Address
0x19
0x1C
Register Name
CH1 - CHB1
IDLE Threshold
CH2 - CHB2
IDLE, RXDET
Bit
Field
Type
R/W
Default
Reserved
3:2
IDLE thd
De-assert threshold
00 = 110 mVp-p (default)
01 = 100 mVp-p
10 = 150 mVp-p
11 = 130 mVp-p
Note: override the SD_TH pin.
1:0
IDLE tha
Assert threshold
00 = 180 mVp-p (default)
01 = 160 mVp-p
10 = 210 mVp-p
11 = 190 mVp-p
Note: override the SD_TH pin.
7:6
Reserved
5
IDLE_AUTO
1: Automatic IDLE detect
0: Allow IDLE_SEL control in bit 4
Note: override IDLE control.
4
IDLE_SEL
1: Output is MUTED (electrical idle)
0: Output is ON
Note: override IDLE control.
3:2
RXDET
00: Input is high-z impedance
01: Auto RX-Detect,
outputs test every 12 ms for 600 ms (50 times) then
stops; termination is high-z until detection; once
detected input termination is 50 Ω
10: Auto RX-Detect,
outputs test every 12 ms until detection occurs;
termination is high-z until detection; once detected
input termination is 50 Ω
11: Input is 50 Ω
Note: override RXDET pin.
R/W
0x00
Description
7:4
0x00
Set bits to 0.
Set bits to 0.
1:0
Reserved
0x1D
CH2 - CHB2
EQ
7:0
EQ Control
R/W
0x2F
IB2 EQ Control - total of 256 levels.
See Table 2.
0x1E
CH2 - CHB2
VOD
7
Short Circuit
Protection
R/W
0xAD
1: Enable the short circuit protection
0: Disable the short circuit protection
6
MODE_SEL
1: Gen 1/2,
0: PCIe Gen 3
Note: override the MODE pin.
5:3
Reserved
Set bits to default value - 101.
2:0
VOD Control
OB2 VOD Control
000: 0.7 V
001: 0.8 V
010: 0.9 V
011: 1.0 V
100: 1.1 V
101: 1.2 V (default)
110: 1.3 V
111: 1.4 V
26
Set bits to 0.
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
DS125BR401
www.ti.com
SNLS419C – JULY 2012 – REVISED APRIL 2013
Table 10. SMBUS Slave Mode Register Map (continued)
Address
0x1F
0x20
0x23
0x24
Register Name
CH2 - CHB2
DEM
CH2 - CHB2
IDLE Threshold
CH3 - CHB3
IDLE, RXDET
CH3 - CHB3
EQ
Bit
Field
Type
Default
RXDET STATUS
R
6:5
MODE_DET
STATUS
R
Observation bit for MODE_DET CH2 - CHB2.
00: GEN1 (2.5G)
01: GEN2 (5G)
11: GEN3 (8G+)
4:3
Reserved
R/W
Set bits to 0.
2:0
DEM Control
R/W
OB2 DEM Control
000: 0 dB
001: –1.5 dB
010: –3.5 dB (default)
011: –5 dB
100: –6 dB
101: –8 dB
110: –9 dB
111: –12 dB
7:4
Reserved
R/W
3:2
IDLE thd
De-assert threshold
00 = 110 mVp-p (default)
01 = 100 mVp-p
10 = 150 mVp-p
11 = 130 mVp-p
Note: override the SD_TH pin.
1:0
IDLE tha
Assert threshold
00 = 180 mVp-p (default)
01 = 160 mVp-p
10 = 210 mVp-p
11 = 190 mVp-p
Note: override the SD_TH pin.
7:6
Reserved
5
IDLE_AUTO
1: Automatic IDLE detect
0: Allow IDLE_SEL control in bit 4
Note: override IDLE control.
4
IDLE_SEL
1: Output is MUTED (electrical idle)
0: Output is ON
Note: override IDLE control.
3:2
RXDET
00: Input is high-z impedance
01: Auto RX-Detect,
outputs test every 12 ms for 600 ms (50 times) then
stops; termination is high-z until detection; once
detected input termination is 50 Ω
10: Auto RX-Detect,
outputs test every 12 ms until detection occurs;
termination is high-z until detection; once detected
input termination is 50 Ω
11: Input is 50 Ω
Note: override RXDET pin.
1:0
Reserved
7:0
EQ Control
R/W
0x02
Description
7
0x00
0x00
Observation bit for RXDET CH2 - CHB2.
1: RX = detected
0: RX = not detected
Set bits to 0.
Set bits to 0.
Set bits to 0.
R/W
0x2F
IB3 EQ Control - total of 256 levels.
See Table 2.
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
27
DS125BR401
SNLS419C – JULY 2012 – REVISED APRIL 2013
www.ti.com
Table 10. SMBUS Slave Mode Register Map (continued)
Address
0x25
0x26
0x27
28
Register Name
CH3 - CHB3
VOD
CH3 - CHB3
DEM
CH3 - CHB3
IDLE Threshold
Bit
Field
Type
R/W
Default
0xAD
Description
7
Short Circuit
Protection
6
MODE_SEL
1: Gen 1/2,
0: PCIe Gen 3
Note: override the MODE pin.
5:3
Reserved
Set bits to default value - 101.
2:0
VOD Control
OB0 VOD Control
000: 0.7 V
001: 0.8 V
010: 0.9 V
011: 1.0 V
100: 1.1 V
101: 1.2 V (default)
110: 1.3 V
111: 1.4 V
7
RXDET STATUS
R
6:5
MODE_DET
STATUS
R
Observation bit for MODE_DET CH3 - CHB3.
00: GEN1 (2.5G)
01: GEN2 (5G)
11: GEN3 (8G+)
4:3
Reserved
R/W
Set bits to 0.
2:0
DEM Control
R/W
OB3 DEM Control
000: 0 dB
001: –1.5 dB
010: –3.5 dB (default)
011: –5 dB
100: –6 dB
101: –8 dB
110: –9 dB
111: –12 dB
7:4
Reserved
R/W
3:2
IDLE thd
De-assert threshold
00 = 110 mVp-p (default)
01 = 100 mVp-p
10 = 150 mVp-p
11 = 130 mVp-p
Note: override the SD_TH pin.
1:0
IDLE tha
Assert threshold
00 = 180 mVp-p (default)
01 = 160 mVp-p
10 = 210 mVp-p
11 = 190 mVp-p
Note: override the SD_TH pin.
0x02
0x00
1: Enable the short circuit protection
0: Disable the short circuit protection
Observation bit for RXDET CH3 - CHB3.
1: RX = detected
0: RX = not detected
Set bits to 0.
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
DS125BR401
www.ti.com
SNLS419C – JULY 2012 – REVISED APRIL 2013
Table 10. SMBUS Slave Mode Register Map (continued)
Address
0x2B
Register Name
CH4 - CHA0
IDLE, RXDET
Bit
Field
Type
R/W
Default
0x00
Description
7:6
Reserved
Set bits to 0.
5
IDLE_AUTO
1: Automatic IDLE detect
0: Allow IDLE_SEL control in bit 4
Note: override IDLE control.
4
IDLE_SEL
1: Output is MUTED (electrical idle)
0: Output is ON
Note: override IDLE control.
3:2
RXDET
00: Input is high-z impedance
01: Auto RX-Detect,
outputs test every 12 ms for 600 ms (50 times) then
stops; termination is high-z until detection; once
detected input termination is 50 Ω
10: Auto RX-Detect,
outputs test every 12 ms until detection occurs;
termination is high-z until detection; once detected
input termination is 50 Ω
11: Input is 50 Ω
Note: override RXDET pin.
1:0
Reserved
0x2C
CH4 - CHA0
EQ
7:0
EQ Control
R/W
0x2F
IA0 EQ Control - total of 256 levels.
See Table 2.
0x2D
CH4 - CHA0
VOD
7
Short Circuit
Protection
R/W
0xAD
1: Enable the short circuit protection
0: Disable the short circuit protection
6
MODE_SEL
1: Gen 1/2,
0: PCIe Gen 3
Note: override the MODE pin.
5:3
Reserved
Set bits to default value - 101.
2:0
VOD Control
OA0 VOD Control
000: 0.7 V
001: 0.8 V
010: 0.9 V
011: 1.0 V
100: 1.1 V
101: 1.2 V (default)
110: 1.3 V
111: 1.4 V
7
RXDET STATUS
R
6:5
MODE_DET
STATUS
R
Observation bit for MODE_DET CH4 - CHA0.
00: GEN1 (2.5G)
01: GEN2 (5G)
11: GEN3 (8G+)
4:3
Reserved
R/W
Set bits to 0.
2:0
DEM Control
R/W
OA0 DEM Control
000: 0 dB
001: –1.5 dB
010: –3.5 dB (default)
011: –5 dB
100: –6 dB
101: –8 dB
110: –9 dB
111: –12 dB
0x2E
CH4 - CHA0
DEM
Set bits to 0.
0x02
Observation bit for RXDET CH4 - CHA0.
1: RX = detected
0: RX = not detected
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
29
DS125BR401
SNLS419C – JULY 2012 – REVISED APRIL 2013
www.ti.com
Table 10. SMBUS Slave Mode Register Map (continued)
Address
0x2F
0x32
Register Name
CH4 - CHA0
IDLE Threshold
CH5 - CHA1
IDLE, RXDET
Bit
Field
Type
R/W
Default
Reserved
3:2
IDLE thd
De-assert threshold
00 = 110 mVp-p (default)
01 = 100 mVp-p
10 = 150 mVp-p
11 = 130 mVp-p
Note: override the SD_TH pin.
1:0
IDLE tha
Assert threshold
00 = 180 mVp-p (default)
01 = 160 mVp-p
10 = 210 mVp-p
11 = 190 mVp-p
Note: override the SD_TH pin.
7:6
Reserved
5
IDLE_AUTO
1: Automatic IDLE detect
0: Allow IDLE_SEL control in bit 4
Note: override IDLE control.
4
IDLE_SEL
1: Output is MUTED (electrical idle)
0: Output is ON
Note: override IDLE control.
3:2
RXDET
00: Input is high-z impedance
01: Auto RX-Detect,
outputs test every 12 ms for 600 ms (50 times) then
stops; termination is high-z until detection; once
detected input termination is 50 Ω
10: Auto RX-Detect,
outputs test every 12 ms until detection occurs;
termination is high-z until detection; once detected
input termination is 50 Ω
11: Input is 50 Ω
Note: override RXDET pin.
R/W
0x00
Description
7:4
0x00
Set bits to 0.
Set bits to 0.
1:0
Reserved
0x33
CH5 - CHA1
EQ
7:0
EQ Control
R/W
0x2F
IA1 EQ Control - total of 256 levels.
See Table 2.
0x34
CH5 - CHA1
VOD
7
Short Circuit
Protection
R/W
0xAD
1: Enable the short circuit protection
0: Disable the short circuit protection
6
MODE_SEL
1: Gen 1/2,
0: PCIe Gen 3
Note: override the MODE pin.
5:3
Reserved
Set bits to default value - 101.
2:0
VOD Control
OA1 VOD Control
000: 0.7 V
001: 0.8 V
010: 0.9 V
011: 1.0 V
100: 1.1 V
101: 1.2 V (default)
110: 1.3 V
111: 1.4 V
30
Set bits to 0.
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
DS125BR401
www.ti.com
SNLS419C – JULY 2012 – REVISED APRIL 2013
Table 10. SMBUS Slave Mode Register Map (continued)
Address
0x35
0x36
0x39
0x3A
Register Name
CH5 - CHA1
DEM
CH5 - CHA1
IDLE Threshold
CH6 - CHA2
IDLE, RXDET
CH6 - CHA2
EQ
Bit
Field
Type
Default
RXDET STATUS
R
6:5
MODE_DET
STATUS
R
Observation bit for MODE_DET CH5 - CHA1.
00: GEN1 (2.5G)
01: GEN2 (5G)
11: GEN3 (8G+)
4:3
Reserved
R/W
Set bits to 0.
2:0
DEM Control
R/W
OA1 DEM Control
000: 0 dB
001: –1.5 dB
010: –3.5 dB (default)
011: –5 dB
100: –6 dB
101: –8 dB
110: –9 dB
111: –12 dB
7:4
Reserved
R/W
3:2
IDLE thd
De-assert threshold
00 = 110 mVp-p (default)
01 = 100 mVp-p
10 = 150 mVp-p
11 = 130 mVp-p
Note: override the SD_TH pin.
1:0
IDLE tha
Assert threshold
00 = 180 mVp-p (default)
01 = 160 mVp-p
10 = 210 mVp-p
11 = 190 mVp-p
Note: override the SD_TH pin.
7:6
Reserved
5
IDLE_AUTO
1: Automatic IDLE detect
0: Allow IDLE_SEL control in bit 4
Note: override IDLE control.
4
IDLE_SEL
1: Output is MUTED (electrical idle)
0: Output is ON
Note: override IDLE control.
3:2
RXDET
00: Input is high-z impedance
01: Auto RX-Detect,
outputs test every 12 ms for 600 ms (50 times) then
stops; termination is high-z until detection; once
detected input termination is 50 Ω
10: Auto RX-Detect,
outputs test every 12 ms until detection occurs;
termination is high-z until detection; once detected
input termination is 50 Ω
11: Input is 50 Ω
Note: override RXDET pin.
1:0
Reserved
7:0
EQ Control
R/W
0x02
Description
7
0x00
0x00
Observation bit for RXDET CH5 - CHA1.
1: RX = detected
0: RX = not detected
Set bits to 0.
Set bits to 0.
Set bits to 0.
R/W
0x2F
IA2 EQ Control - total of 256 levels.
See Table 2.
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
31
DS125BR401
SNLS419C – JULY 2012 – REVISED APRIL 2013
www.ti.com
Table 10. SMBUS Slave Mode Register Map (continued)
Address
0x3B
0x3C
0x3D
32
Register Name
CH6 - CHA2
VOD
CH6 - CHA2
DEM
CH6 - CHA2
IDLE Threshold
Bit
Field
Type
R/W
Default
0xAD
Description
7
Short Circuit
Protection
6
MODE_SEL
1: Gen 1/2,
0: PCIe Gen-3
Note: override the MODE pin.
5:3
Reserved
Set bits to default value - 101.
2:0
VOD Control
OA2 VOD Control
000: 0.7 V
001: 0.8 V
010: 0.9 V
011: 1.0 V
100: 1.1 V
101: 1.2 V (default)
110: 1.3 V
111: 1.4 V
7
RXDET STATUS
R
6:5
MODE_DET
STATUS
R
Observation bit for MODE_DET CH6 - CHA2.
00: GEN1 (2.5G)
01: GEN2 (5G)
11: GEN3 (8G+)
4:3
Reserved
R/W
Set bits to 0.
2:0
DEM Control
R/W
OA2 DEM Control
000: 0 dB
001: –1.5 dB
010: –3.5 dB (default)
011: –5 dB
100: –6 dB
101: –8 dB
110: –9 dB
111: –12 dB
7:4
Reserved
R/W
3:2
IDLE thd
De-assert threshold
00 = 110 mVp-p (default)
01 = 100 mVp-p
10 = 150 mVp-p
11 = 130 mVp-p
Note: override the SD_TH pin.
1:0
IDLE tha
Assert threshold
00 = 180 mVp-p (default)
01 = 160 mVp-p
10 = 210 mVp-p
11 = 190 mVp-p
Note: override the SD_TH pin.
0x02
0x00
1: Enable the short circuit protection
0: Disable the short circuit protection
Observation bit for RXDET CH6 - CHA2.
1: RX = detected
0: RX = not detected
Set bits to 0.
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
DS125BR401
www.ti.com
SNLS419C – JULY 2012 – REVISED APRIL 2013
Table 10. SMBUS Slave Mode Register Map (continued)
Address
0x40
Register Name
CH7 - CHA3
IDLE, RXDET
Bit
Field
Type
R/W
Default
0x00
Description
7:6
Reserved
Set bits to 0.
5
IDLE_AUTO
1: Automatic IDLE detect
0: Allow IDLE_SEL control in bit 4
Note: override IDLE control.
4
IDLE_SEL
1: Output is MUTED (electrical idle)
0: Output is ON
Note: override IDLE control.
3:2
RXDET
00: Input is high-z impedance
01: Auto RX-Detect,
outputs test every 12 ms for 600 ms (50 times) then
stops; termination is high-z until detection; once
detected input termination is 50 Ω
10: Auto RX-Detect,
outputs test every 12 ms until detection occurs;
termination is high-z until detection; once detected
input termination is 50 Ω
11: Input is 50 Ω
Note: override RXDET pin.
1:0
Reserved
0x41
CH7 - CHA3
EQ
7:0
EQ Control
R/W
0x2F
IA3 EQ Control - total of 256 levels.
See Table 2.
0x42
CH7 - CHA3
VOD
7
Short Circuit
Protection
R/W
0xAD
1: Enable the short circuit protection
0: Disable the short circuit protection
6
MODE_SEL
1: Gen 1/2,
0: PCIe Gen 3
Note: override the MODE pin.
5:3
Reserved
Set bits to default value - 101.
2:0
VOD Control
OA3 VOD Control
000: 0.7 V
001: 0.8 V
010: 0.9 V
011: 1.0 V
100: 1.1 V
101: 1.2 V (default)
110: 1.3 V
111: 1.4 V
7
RXDET STATUS
R
6:5
MODE_DET
STATUS
R
Observation bit for MODE_DET CH7 - CHA3.
00: GEN1 (2.5G)
01: GEN2 (5G)
11: GEN3 (8G+)
4:3
Reserved
R/W
Set bits to 0.
2:0
DEM Control
R/W
OA3 DEM Control
000: 0 dB
001: –1.5 dB
010: –3.5 dB (default)
011: –5 dB
100: –6 dB
101: –8 dB
110: –9 dB
111: –12 dB
0x43
CH7 - CHA3
DEM
Set bits to 0.
0x02
Observation bit for RXDET CH7 - CHA3.
1: RX = detected
0: RX = not detected
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
33
DS125BR401
SNLS419C – JULY 2012 – REVISED APRIL 2013
www.ti.com
Table 10. SMBUS Slave Mode Register Map (continued)
Address
0x44
0x51
34
Register Name
CH7 - CHA3
IDLE Threshold
Device ID
Bit
Field
Type
R/W
Default
Reserved
3:2
IDLE thd
De-assert threshold
00 = 110 mVp-p (default)
01 = 100 mVp-p
10 = 150 mVp-p
11 = 130 mVp-p
Note: override the SD_TH pin.
1:0
IDLE tha
Assert threshold
00 = 180 mVp-p (default)
01 = 160 mVp-p
10 = 210 mVp-p
11 = 190 mVp-p
Note: override the SD_TH pin.
7:5
VERSION
4:0
ID
R
0x00
Description
7:4
0x44
Set bits to 0.
010'b
00100'b
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
DS125BR401
www.ti.com
SNLS419C – JULY 2012 – REVISED APRIL 2013
APPLICATIONS INFORMATION
The DS125BR401 is a high performance circuit capable of delivering excellent performance. Careful attention
must be paid to the details associated with high-speed design as well as providing a clean power supply. Refer
to the information below and Revision 4 of the LVDS Owner's Manual for more detailed information on high
speed design tips to address signal integrity design issues.
PCB LAYOUT CONSIDERATIONS FOR DIFFERENTIAL PAIRS
The CML inputs and LPDS outputs have been optimized to work with interconnects using a controlled differential
impedance of 85 - 100Ω. It is preferable to route differential lines exclusively on one layer of the board,
particularly for the input traces. The use of vias should be avoided if possible. If vias must be used, they should
be used sparingly and must be placed symmetrically for each side of a given differential pair. Whenever
differential vias are used the layout must also provide for a low inductance path for the return currents as well.
Route the differential signals away from other signals and noise sources on the printed circuit board. See AN1187 “Leadless Leadframe Package (LLP) Application Report” (literature number SNOA401) for additional
information on QFN (WQFN) packages.
20 mils
EXTERNAL MICROSTRIP
100 mils
20 mils
INTERNAL STRIPLINE
VDD
VDD
18 17 16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
19
54
20
53
21
52
51
22
BOTTOM OF PKG
23
VDD
50
GND
24
49
25
48
26
47
27
46
28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45
VDD
VDD
Figure 6. Typical Routing Options
The graphic shown above depicts different transmission line topologies which can be used in various
combinations to achieve the optimal system performance. Impedance discontinuities at the differential via can be
minimized or eliminated by increasing the swell around each hole and providing for a low inductance return
current path. When the via structure is associated with thick backplane PCB, further optimization such as back
drilling is often used to reduce the deterimential high frequency effects of stubs on the signal path.
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
35
DS125BR401
SNLS419C – JULY 2012 – REVISED APRIL 2013
www.ti.com
POWER SUPPLY BYPASSING
Two approaches are recommended to ensure that the DS125BR401 is provided with an adequate power supply.
First, the supply (VDD) and ground (GND) pins should be connected to power planes routed on adjacent layers
of the printed circuit board. The layer thickness of the dielectric should be minimized so that the VDD and GND
planes create a low inductance supply with distributed capacitance. Second, careful attention to supply
bypassing through the proper use of bypass capacitors is required. A 0.1 μF bypass capacitor should be
connected to each VDD pin such that the capacitor is placed as close as possible to the DS125BR401. Smaller
body size capacitors can help facilitate proper component placement. Additionally, capacitor with capacitance in
the range of 1 μF to 10 μF should be incorporated in the power supply bypassing design as well. These
capacitors can be either tantalum or an ultra-low ESR ceramic.
36
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
DS125BR401
www.ti.com
SNLS419C – JULY 2012 – REVISED APRIL 2013
Typical Performance Curves Characteristics
1021
640.0
VDD = 2.625V
620.0
T = 25°C
VDD = 2.5V
600.0
1019
VDD = 2.375V
560.0
VOD (mVp-p)
PD (mW)
580.0
540.0
520.0
500.0
1016
1013
480.0
T = 25oC
460.0
1010
440.0
420.0
0.8
0.9
1
1.1
1.2
1007
2.375
1.3
2.5
2.625
VOD (Vp-p)
VDD (V)
Figure 7. Power Dissipation (PD) vs. Output Differential
Voltage (VOD)
Figure 8. Output Differential Voltage (VOD = 1.0 Vp-p) vs.
Supply Voltage (VDD)
1020
VDD = 2.5 V
VOD (mVp-p)
1018
1016
1014
1012
- 40
-15
10
35
60
85
TEMPERATURE (°C)
Figure 9. Output Differential Voltage (VOD = 1.0 Vp-p) vs. Temperature
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
37
DS125BR401
SNLS419C – JULY 2012 – REVISED APRIL 2013
www.ti.com
Typical Performance Eye Diagrams Characteristics
Pattern
Generator
VID = 1.0 Vp-p,
DE = 0 dB
PRBS15
TL
Lossy Channel
IN
DS125BR401
OUT
Scope
BW = 60 GHz
Figure 10. Test Setup Connections Diagram
DS125BR401 settings: EQ[1:0] = 0, F = 02'h, DEM[1:0] = 0, 1
Figure 11. TL = 10 inch 5–mil FR4 trace, 5 Gbps
DS125BR401 settings: EQ[1:0] = 0, F = 02'h, DEM[1:0] = 0, 1
Figure 12. TL = 10 inch 5–mil FR4 trace, 8 Gbps
38
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
DS125BR401
www.ti.com
SNLS419C – JULY 2012 – REVISED APRIL 2013
Typical Performance Eye Diagrams Characteristics (continued)
DS125BR401 settings: EQ[1:0] = 0, R = 01'h, DEM[1:0] = 0, 1
Figure 13. TL = 10 inch 5–mil FR4 trace, 12 Gbps
DS125BR401 settings: EQ[1:0] = 0, 1 = 03'h, DEM[1:0] = 0, 1
Figure 14. TL = 20 inch 5–mil FR4 trace, 5 Gbps
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
39
DS125BR401
SNLS419C – JULY 2012 – REVISED APRIL 2013
www.ti.com
Typical Performance Eye Diagrams Characteristics (continued)
DS125BR401 settings: EQ[1:0] = 0, 1 = 03'h, DEM[1:0] = 0, 1
Figure 15. TL = 20 inch 5–mil FR4 trace, 8 Gbps
DS125BR401 settings: EQ[1:0] = 0, 1 = 03'h, DEM[1:0] = 0, 1
Figure 16. TL = 20 inch 5–mil FR4 trace, 12 Gbps
40
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
DS125BR401
www.ti.com
SNLS419C – JULY 2012 – REVISED APRIL 2013
Typical Performance Eye Diagrams Characteristics (continued)
DS125BR401 settings: EQ[1:0] = R, 0 = 07'h, DEM[1:0] = 0, 1
Figure 17. TL = 30 inch 5–mil FR4 trace, 5 Gbps
DS125BR401 settings: EQ[1:0] = R, 0 = 07'h, DEM[1:0] = 0, 1
Figure 18. TL = 30 inch 5–mil FR4 trace, 8 Gbps
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
41
DS125BR401
SNLS419C – JULY 2012 – REVISED APRIL 2013
www.ti.com
Typical Performance Eye Diagrams Characteristics (continued)
DS125BR401 settings: EQ[1:0] = R, 0 = 07'h, DEM[1:0] = 0, 1
Figure 19. TL = 30 inch 5–mil FR4 trace, 12 Gbps
DS125BR401 settings: EQ[1:0] = R, 0 = 07'h, DEM[1:0] = 0, 1
Figure 20. TL1 = 5-meter 30-AWG 100 Ohm Twin-axial Cable, 12 Gbps
42
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
DS125BR401
www.ti.com
SNLS419C – JULY 2012 – REVISED APRIL 2013
Typical Performance Eye Diagrams Characteristics (continued)
DS125BR401 settings: EQ[1:0] = R, 1 = 0F'h, DEM[1:0] = 0, 1
Figure 21. TL1 = 8-meter 30-AWG 100 Ohm Twin-axial Cable, 12 Gbps
Pattern
Generator
VID = 1.0 Vp-p,
DE = -6 dB
PRBS15
TL1
Lossy Channel
IN
DS125BR401
OUT
TL2
Lossy Channel
Scope
BW = 60 GHz
Figure 22. Test Setup Connections Diagram
DS125BR401 settings: EQ[1:0] = 0, 1 = 03'h, DEM[1:0] = R, 0
Figure 23. TL1 = 20 inch 5–mil FR4 trace, TL2 = 10 inch 5–mil FR4 trace, 5 Gbps
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
43
DS125BR401
SNLS419C – JULY 2012 – REVISED APRIL 2013
www.ti.com
Typical Performance Eye Diagrams Characteristics (continued)
DS125BR401 settings: EQ[1:0] = R, 1 = 0F'h, DEM[1:0] = R, 0
Figure 24. TL1 = 20 inch 5–mil FR4 trace, TL2 = 10 inch 5–mil FR4 trace, 8 Gbps
DS125BR401 settings: EQ[1:0] = R, 1 = 0F'h, DEM[1:0] = R, 0
Figure 25. TL1 = 20 inch 5–mil FR4 trace, TL2 = 10 inch 5–mil FR4 trace, 12 Gbps
44
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
DS125BR401
www.ti.com
SNLS419C – JULY 2012 – REVISED APRIL 2013
REVISION HISTORY
Changes from Revision C (April 2013) to Revision D
•
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 44
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS125BR401
45
PACKAGE OPTION ADDENDUM
www.ti.com
16-Apr-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
DS125BR401SQ/NOPB
ACTIVE
WQFN
NJY
54
2000
Green (RoHS
& no Sb/Br)
CU SN
Level-2-260C-1 YEAR
DS125BR401SQ
DS125BR401SQE/NOPB
ACTIVE
WQFN
NJY
54
250
Green (RoHS
& no Sb/Br)
CU SN
Level-2-260C-1 YEAR
DS125BR401SQ
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
Samples
PACKAGE MATERIALS INFORMATION
www.ti.com
24-Apr-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
DS125BR401SQ/NOPB
WQFN
NJY
54
2000
330.0
16.4
5.8
10.3
1.0
12.0
16.0
Q1
DS125BR401SQE/NOPB
WQFN
NJY
54
250
178.0
16.4
5.8
10.3
1.0
12.0
16.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
24-Apr-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
DS125BR401SQ/NOPB
WQFN
NJY
54
2000
367.0
367.0
38.0
DS125BR401SQE/NOPB
WQFN
NJY
54
250
213.0
191.0
55.0
Pack Materials-Page 2
PACKAGE OUTLINE
NJY0054A
WQFN
SCALE 2.000
WQFN
5.6
5.4
B
A
PIN 1 INDEX AREA
0.5
0.3
0.3
0.2
10.1
9.9
DETAIL
OPTIONAL TERMINAL
TYPICAL
0.8 MAX
C
SEATING PLANE
2X 4
SEE TERMINAL
DETAIL
3.51±0.1
19
(0.1)
27
28
18
50X 0.5
7.5±0.1
2X
8.5
1
45
54
PIN 1 ID
(OPTIONAL)
46
54X
54X
0.5
0.3
0.3
0.2
0.1
0.05
C A
C
B
4214993/A 07/2013
NOTES:
1. All linear dimensions are in millimeters. Dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. The package thermal pad must be soldered to the printed circuit board for thermal and mechanical performance.
www.ti.com
EXAMPLE BOARD LAYOUT
NJY0054A
WQFN
WQFN
(3.51)
SYMM
54X (0.6)
54
54X (0.25)
SEE DETAILS
46
1
45
50X (0.5)
(7.5)
SYMM
(9.8)
(1.17)
TYP
2X
(1.16)
28
18
( 0.2) TYP
VIA
19
27
(1) TYP
(5.3)
LAND PATTERN EXAMPLE
SCALE:8X
0.07 MIN
ALL AROUND
0.07 MAX
ALL AROUND
METAL
SOLDER MASK
OPENING
SOLDER MASK
OPENING
NON SOLDER MASK
DEFINED
(PREFERRED)
METAL
SOLDER MASK
DEFINED
SOLDER MASK DETAILS
4214993/A 07/2013
NOTES: (continued)
4. This package is designed to be soldered to a thermal pad on the board. For more information, refer to QFN/SON PCB application note
in literature No. SLUA271 (www.ti.com/lit/slua271).
www.ti.com
EXAMPLE STENCIL DESIGN
NJY0054A
WQFN
WQFN
SYMM
METAL
TYP
(0.855) TYP
46
54
54X (0.6)
54X (0.25)
1
45
50X (0.5)
(1.17)
TYP
SYMM
(9.8)
12X (0.97)
18
28
19
27
12X (1.51)
(5.3)
SOLDERPASTE EXAMPLE
BASED ON 0.125mm THICK STENCIL
EXPOSED PAD
67% PRINTED SOLDER COVERAGE BY AREA
SCALE:10X
4214993/A 07/2013
NOTES: (continued)
5. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated