DALLAS DS1775R/TR3

PRODUCT PREVIEW
PRELIMINARY
DS1775
SOT23-5 Digital Thermometer
and Thermostat
www.dalsemi.com
FEATURES
§ Temperature measurements require no
external components
§ Measures temperatures from –55°C to
+125°C. Fahrenheit equivalent is –67°F to
257°F
§ Thermometer accuracy is ±2.0°C
§ Thermometer resolution is configurable from
9 to 12 bits (0.5°C to 0.0625°C resolution)
§ Thermostat settings are user definable
§ Data is read from/written to via a 2–wire
serial interface
§ Wide power supply range (2.7V – 5.5V)
§ Software compatible with DS75 2–Wire
Thermal Watchdog in thermometer mode
§ Space–conscious SOT23–5 package with
low thermal time constant
PIN ASSIGNMENT
SCL
1
GND
2
O.S.
3
5
SDA
4
VDD
DS1775R
SOT23-5
PIN DESCRIPTION
GND
SCL
SDA
VDD
O.S.
Ground
2–Wire Serial Clock
2–Wire Serial Data Input/Output
Power Supply Voltage
Thermostat Output Signal
ORDERING INFORMATION
Part Number
Address
DS1775R/TRL
000
DS1775R/TR1
001
DS1775R/TR2
010
DS1775R/TR3
011
* "R" denotes SOT 23-5 Package
Part Number
DS1775R/TR4
DS1775R/TR5
DS1775R/TR6
DS1775R/TR7
Address
100
101
110
111
DESCRIPTION
The DS1775 SOT23-5 Digital Thermometer and Thermostat provides temperature readings which
indicate the temperature of the device. Thermostat settings and temperature readings are all
communicated to/from the DS1775 over a simple 2–wire serial interface. No additional components are
required; the device is truly a “temperature–to–digital” converter.
For applications that require greater temperature resolution, the user can adjust the readout resolution
from 9 to 12 bits. This is particularly useful in applications where thermal runaway conditions must be
detected quickly.
The open–drain thermal alarm output, O.S., becomes active when the temperature of the device exceeds a
user–defined temperature TOS. The number of consecutive faults required to set O.S. active is
configurable by the user. The device can also be configured in the interrupt or comparator mode, to
customize the method which clears the fault condition.
1 of 13
102299
DS1775
As a digital thermometer, the DS1775 is software compatible with the DS75 2–Wire Thermal Watchdog.
The DS1775 is assembled in a compact SOT23–5 package allowing for low–cost thermal
monitoring/control in space–constrained applications. The low thermal mass allows for time constants
previously only possible with thermistors.
Applications for the DS1775 include personal computers/servers/workstations, cellular telephones, office
equipment, or any thermally–sensitive system.
DETAILED PIN DESCRIPTION Table 1
PIN
PIN 1
SYMBOL
SCL
PIN 2
PIN 3
GND
O.S.
PIN 4
PIN 5
VDD
SDA
DESCRIPTION
Clock input/output pin for 2-wire serial communication port. This input
should be tied to GND for standalone thermostat operation.
Ground pin.
Thermostat output Open-drain output becomes active when temperature
exceeds TOS. Device configuration defines means to clear over-temperature
state.
Supply Voltage 2.7V – 5.5V input power pin.
Data input/output pin for 2-wire serial communication port. In the standalone
thermostat mode, this input selects hysteresis.
OVERVIEW
A block diagram of the DS1775 is shown in Figure 1. The DS1775 consists of five major components:
1. Precision temperature sensor
2. Analog–to–digital converter
3. 2–wire interface electronics
4. Data registers
5. Thermostat comparator
The factory–calibrated temperature sensor requires no external components. Upon power–up, the DS1775
begins temperature conversions with the default resolution of 9 bits (0.5°C resolution). The host can
periodically read the value in the temperature register, which contains the last completed conversion. As
conversions are performed in the background, reading the temperature register does not affect the
conversion in progress.
In power–sensitive applications the user can put the DS1775 into a shutdown mode, under which the
sensor will complete and store the conversion in progress and revert to a low–power standby state. In
applications where small incremental temperature changes are critical, the user can change the conversion
resolution from 9 bits to 10, 11, or 12. Each additional bit of resolution approximately doubles the
conversion time. This is accomplished by programming the configuration register. The configuration
register defines the conversion state, thermometer resolution/conversion time, active state of the
thermostat output, number of consecutive faults to trigger an alarm condition, and the method to
terminate an alarm condition.
The user can also program over–temperature (TOS) and under–temperature (THYST) setpoints for
thermostatic operation. The power–up state of TOS is 80°C and that for THYST is 75°C. The result of each
temperature conversion is compared with the TOS and THYST setpoints. The DS1775 offers two modes for
temperature control, the comparator mode and the interrupt mode. This allows the user the flexibility to
customize the condition that would generate and clear a fault condition. Regardless of the mode chosen,
2 of 13
102299
DS1775
the O.S. output will become active only after the measured temperature exceeds the respective trippoint a
consecutive number of times; the number of consecutive conversions beyond the limit to generate an O.S.
is programmable. The power–up state of the DS1775 is in the comparator mode with a single fault
generating an active O.S.
Digital data is written to/read from the DS1775 via a 2–wire interface, and all communication is MSb
first.
DS1775 FUNCTIONAL BLOCK DIAGRAM Figure 1
OPERATION–Measuring Temperature
The core of DS1775 functionality is its direct–to–digital temperature sensor. The DS1775 measures
temperature through the use of an on–chip temperature measurement technique with an operating range
from –55°C to +125°C. Temperature conversions are initiated upon power–up, and the most recent result
is stored in the thermometer register. Conversions are performed continuously unless the user intervenes
by altering the configuration register to put the DS1775 into a shutdown mode. Regardless of the mode
used, the digital temperature can be retrieved from the temperature register by setting the pointer to that
location (00h, power–up default). The DS1775 power–up default has the sensor automatically performing
9–bit conversions continuously. Details on how to change the settings after power–up are contained in the
“OPERATION–Programming” section.
3 of 13
102299
DS1775
The resolution of the temperature conversion is configurable (9, 10, 11, or 12 bits), with 9–bit readings
the default state. This equates to a temperature resolution of 0.5°C, 0.25°C, 0.125°C, or 0.0625°C.
Following each conversion, thermal data is stored in the thermometer register in two’s complement
format; the information can be retrieved over the 2–wire interface with the device pointer set to the
temperature register. Table 2 describes the exact relationship of output data to measured temperature. The
table assumes the DS1775 is configured for 12–bit resolution; if the device is configured in a lower
resolution mode, those bits will contain zeros. The data is transmitted serially over the 2–wire serial
interface, MSb first. The MSb of the temperature register contains the “sign” (S) bit, denoting whether the
temperature is positive or negative. For Fahrenheit usage, a lookup table or conversion routine must be
used.
Temperature/Data Relationships Table 2
S
26
25
-2
-3
2
23
22
21
(UNIT = °C)
MSb
-1
24
2
TEMP
+125°C
+25.0625°C
+10.125°C
+0.5°C
+0°C
-0.5°C
-10.125°C
-25.0625°C
-55°C
2
-4
2
20
MSB
LSb
0
0
DIGITAL OUTPUT
(Binary)
0111 1101 0000 0000
0000 1010 0010 0000
0000 1010 0010 0000
0000 0000 1000 0000
0000 0000 0000 0000
1111 1111 1000 0000
1111 0101 1110 0000
1110 0110 1111 0000
1100 1001 0000 0000
0
0
LSB
DIGITAL OUTPUT (Hex)
7D00h
1910h
0A20h
0080h
0000h
FF80h
F5E0h
E6F0h
C900h
OPERATION–Thermostat Control
In its comparator operating mode, the DS1775 functions as a thermostat with programmable hysteresis, as
shown in Figure 2. When the DS1775’s temperature meets or exceeds the value stored in the high
temperature trip register (TOS) a consecutive number of times, as defined by the configuration register, the
output becomes active and stays active until the first time that the temperature falls below the temperature
stored in the low temperature trigger register (THYST). In this way, any amount of hysteresis may be
obtained. The DS1775 powers up in the comparator mode with TOS=80°C and THYST=75°C and can be
used as a standalone thermostat (no 2–wire interface required) with those setpoints.
In the interrupt mode, the O.S. output will first become active following the programmed number of
consecutive conversions above TOS. The fault can only be cleared by either setting the DS1775 in a
shutdown mode or by reading any register (temperature, configuration, TOS, or THYST) on the device.
Following a clear, a subsequent fault can only occur if consecutive conversions fall below THYST. This
interrupt/clear process is thus cyclical (TOS, clear, THYST, clear, TOS, clear, THYST, clear, ...). Only the first
of multiple consecutive TOS violations will activate O.S., even if each fault is separated by a clearing
function. The same situation applies to multiple consecutive THYST events.
4 of 13
102299
DS1775
O.S. OUTPUT TRANSFER FUNCTION Figure 2
Regardless of the mode chosen, the O.S. output is open–drain and the active state is set in the
configuration register. The power–up default is active low. Refer to the “OPERATION–Programming”
section for instructions in adjusting the thermostat setpoints, thermostat mode, and O.S. active state.
OPERATION–Programming
There are three areas of interest in programming the DS1775: the configuration register, the TOS register,
and the THYST register. All programming is done via the 2–wire interface by setting the pointer to the
appropriate location. Table 3 illustrates the pointer settings for the four registers of the DS1775.
Pointer Register Structure Table 3
POINTER
00h
01h
02h
03h
ACTIVE REGISTER
Temperature (default)
Configuration
THYST
TOS
The DS1775 will power up with the temperature register selected. If the host wishes to change the data
pointer it simply addresses the DS1775 in the write mode (R/ W =0), receives an acknowledge, and writes
the 8 bits that correspond to the new desired location. The last pointer location is always maintained so
that consecutive reads from the same register do not require the host to always provide a pointer address.
5 of 13
102299
DS1775
The only exception is at power–up, in which case the pointer will always be set to 00h, the temperature
register. The pointer address must always proceed data in writing to a register, regardless of which
address is currently selected. Please refer to the “2–Wire Serial Data Bus” section for details of the 2–
wire bus protocol.
Configuration Register Programming
The configuration register is accessed if the DS1775 pointer is currently set to the 01h location. Writing
to or reading from the register is determined by the R/W bit of the 2–wire control byte (See “2–wire
Serial Data Bus” section). Data is read from or written to the configuration register MSb first. The format
of the register is illustrated below in Figure 3. The effect each bit has on DS1775 functionality is
described below along with the power–up state of the bit. The user has read/write access to all bits in the
configuration register. The entire register is volatile, and thus it will power–up in the default state.
Configuration/Status Register Figure 3
0
MSb
R1
R0
F1
F0
POL
TM
SD
LSb
SD = Shutdown bit. If SD is “0”, the DS1775 will continuously perform temperature conversions and
store the last completed result in the thermometer register. If SD is changed to “1”, the conversion in
progress will be completed and stored; then the device will revert to a low–power standby mode. The
O.S. output will be cleared if the device is in the interrupt mode and remain unchanged in the comparator
mode. The 2–wire port remains active. The power–up default state is “0” (continuous conversion mode).
TM = Thermostat mode. If TM=“0”, the DS1775 is in the comparator mode. TM=“1” sets the device to
the interrupt mode. See “OPERATION–Thermostat Control” section for a description of the difference
between the two modes. The power–up default state of the TM bit is “0” (comparator mode).
POL = O.S. Polarity Bit. If POL = “1”, the active state of the O.S. output will be high. A “0” stored in
this location sets the thermostat output to an active low state. The user has read/write access to the POL
bit, and the power–up default state is “0” (active low).
F0, F1 = O.S. Fault Tolerance bits. The fault tolerance defines the number of consecutive conversions
returning a temperature beyond limits is required to set the O.S. output in an active state. This may be
necessary to add margin in noisy environments. Table 4 below defines the four settings. The DS1775 will
power up with F0=F1=“0”, such that a single occurrence will trigger a fault.
Fault Tolerance Configuration Table 4
F1
0
0
1
1
F0
0
1
0
1
Consecutive conversions beyond limits to generate fault
1
2
4
6
R0, R1 = Thermometer resolution bits. Table 5 defines the resolution of the digital thermometer, based
on the settings of these two bits. There is a direct trade-off between resolution and conversion time, as
depicted in the AC Electrical Characteristics. The default state is R0="0" and R1="0" (9–bit conversions).
6 of 13
102299
DS1775
Thermometer Resolution Configuration Table 5
R1
0
0
1
1
R0
0
1
0
1
Thermometer Resolution
9-bit
10-bit
11-bit
12-bit
Max Conversion Time
0.15s
0.3s
0.6s
1.2s
Thermostat Setpoints Programming
The thermostat registers (TOS and THYST) can be programmed or read via the 2–wire interface. TOS is
accessed by setting the DS1775 data pointer to the 03h location, and to the 02h location for THYST.
The format of the TOS and THYST registers is identical to that of the Thermometer register; that is, 12–bit
2’s complement representation of the temperature in °C. The user can program the number of bits (9, 10,
11, or 12) for each TOS and THYST that corresponds to the thermometer resolution mode chosen. For
example, if the 9–bit mode is chosen the 3 least significant bits of TOS and THYST will be ignored by the
thermostat comparator. The format for both TOS and THYST is shown in Table 6. The power–up default
for TOS is 80°C and for THYST is 75°C.
Thermostat Setpoint (TOS/THYST) Format Table 6
S
26
25
-2
-3
24
23
22
21
(UNIT = °C)
MSb
-1
2
2
2
2
-4
0
20
MSB
LSb
0
0
0
LSB
TEMPERATURE/DATA RELATIONSHIPS
TEMP
DIGITAL OUTPUT
DIGITAL OUTPUT (Hex)
(Binary)
0101 0000 0000 0000
5000h
+80°C
0100
1011
0000
0000
4B00h
+75°C
0000 1010 0010 0000
0A20h
+10.125°C
0000 0000 1000 0000
0080h
+0.5°C
0000 0000 0000 0000
0000h
+0°C
1111 1111 1000 0000
FF80h
-0.5°C
1111
0101
1110
0000
F5E0h
-10.125°C
1110 0110 1111 0000
E6F0h
-25.0625°C
1100 1001 0000 0000
C900h
-55°C
If the user does not wish to take advantage of the thermostat capabilities of the DS1775, the 24 bits can be
used for general storage of system data that need not be maintained following a power loss.
2–WIRE SERIAL DATA BUS
The DS1775 supports a bi–directional 2-wire bus and data transmission protocol. A device that sends data
onto the bus is defined as a transmitter, and a device receiving data as a receiver. The device that controls
the message is called a “master”. The devices that are controlled by the master are “slaves”. The bus must
be controlled by a master device which generates the serial clock (SCL), controls the bus access, and
generates the START and STOP conditions. The DS1775 operates as a slave on the two–wire bus.
Connections to the bus are made via the open–drain I/O lines SDA and SCL.
The following bus protocol has been defined (See Figure 4):
7 of 13
102299
DS1775
• Data transfer may be initiated only when the bus is not busy.
• During data transfer, the data line must remain stable whenever the clock line is HIGH. Changes in
the data line while the clock line is high will be interpreted as control signals.
Accordingly, the following bus conditions have been defined:
Bus not busy: Both data and clock lines remain HIGH.
Start data transfer: A change in the state of the data line, from HIGH to LOW, while the clock is HIGH,
defines a START condition.
Stop data transfer: A change in the state of the data line, from LOW to HIGH, while the clock line is
HIGH, defines the STOP condition.
Data valid: The state of the data line represents valid data when, after a START condition, the data line
is stable for the duration of the HIGH period of the clock signal. The data on the line must be changed
during the LOW period of the clock signal. There is one clock pulse per bit of data.
Each data transfer is initiated with a START condition and terminated with a STOP condition. The
number of data bytes transferred between START and STOP conditions is not limited, and is determined
by the master device. The information is transferred byte–wise and each receiver acknowledges with a
ninth bit.
Within the bus specifications a regular mode (100kHz clock rate) and a fast mode (400kHz clock rate) are
defined. The DS1775 works in both modes.
Acknowledge: Each receiving device, when addressed, is obliged to generate an acknowledge after the
reception of each byte. The master device must generate an extra clock pulse which is associated with this
acknowledge bit.
A device that acknowledges must pull down the SDA line during the acknowledge clock pulse in such a
way that the SDA line is stable LOW during the HIGH period of the acknowledge related clock pulse. Of
course, setup and hold times must be taken into account. A master must signal an end of data to the slave
by not generating an acknowledge bit on the last byte that has been clocked out of the slave. In this case,
the slave must leave the data line HIGH to enable the master to generate the STOP condition.
DATA TRANSFER ON 2–WIRE SERIAL BUS Figure 4
8 of 13
102299
DS1775
Figure 5 details how data transfer is accomplished on the two–wire bus. Depending upon the state of the
R/W bit, two types of data transfer are possible:
1. Data transfer from a master transmitter to a slave receiver. The first byte transmitted by the
master is the slave address. Next follows a number of data bytes. The slave returns an acknowledge
bit after each received byte.
2. Data transfer from a slave transmitter to a master receiver. The first byte (the slave address) is
transmitted by the master. The slave then returns an acknowledge bit. Next follows a number of data
bytes transmitted by the slave to the master. The master returns an acknowledge bit after all received
bytes other than the last byte. At the end of the last received byte, a ‘not acknowledge’ is returned.
The master device generates all of the serial clock pulses and the START and STOP conditions. A
transfer is ended with a STOP condition or with a repeated START condition. Since a repeated START
condition is also the beginning of the next serial transfer, the bus will not be released.
The DS1775 may operate in the following two modes:
1. Slave receiver mode: Serial data and clock are received through SDA and SCL. After each byte is
received, an acknowledge bit is transmitted. START and STOP conditions are recognized as the
beginning and end of a serial transfer. Address recognition is performed by hardware after reception
of the slave address and direction bit.
2. Slave transmitter mode: The first byte is received and handled as in the slave receiver mode.
However, in this mode, the direction bit will indicate that the transfer direction is reversed. Serial data
is transmitted on SDA by the DS1775 while the serial clock is input on SCL. START and STOP
conditions are recognized as the beginning and end of a serial transfer.
SLAVE ADDRESS
A control byte is the first byte received following the START condition from the master device. The
control byte consists of a four bit control code; for the DS1775, this is set as 1001 binary for read and
write operations. The next three bits of the control byte are the device select bits (A2, A1, A0). These bits
are set to 000 (A2="0", A1="0", A0="0") for the DS1775R/TRL and vary according to the device's part
number as specified in the "Ordering Information" section. They are used by the master device to select
which of eight devices are to be accessed. The set bits are in effect the three least significant bits of the
slave address. The last bit of the control byte (R/ W ) defines the operation to be performed. When set to a
"1" a read operation is selected, and when set to a "0" a write operation is selected. Following the START
condition, the DS1775 monitors the SDA bus checking the device type identifier being transmitted. Upon
receiving the 1001 code and appropriate device select bits of 000, the DS1775 outputs an acknowledge
signal on the SDA line.
9 of 13
102299
DS1775
2–WIRE SERIAL COMMUNICATION WITH DS1775 Figure 5
10 of 13
102299
DS1775
ABSOLUTE MAXIMUM RATINGS*
Voltage on VDD, Relative to Ground
–0.3V to +7.0V
Voltage on any other pin, Relative to Ground
–0.3V to +7.0V
Operating Temperature
–55°C to +125°C
Storage Temperature
–55°C to +125°C
Soldering Temperature
260°C for 10 seconds
* This is a stress rating only and functional operation of the device at these or any other conditions above
those indicated in the operation sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods of time may affect reliability.
RECOMMENDED DC OPERATING CONDITIONS
(–55°C to +125°C; 2.7V ≤VDD ≤5.5V)
PARAMETER
SYMBOL
Supply Voltage
VDD
CONDITION
MIN
2.7
TYP
MAX
5.5
UNITS
V
NOTES
1
(–55°C to +125°C; 2.7V ≤VDD ≤5.5V)
CONDITION
MIN
TYP
MAX
UNITS NOTES
0.7 VDD
VDD+0.5
V
1
-0.5
0.3VDD
V
1
3 mA sink
0
0.4
V
1
current
6 mA sink
0
0.6
current
4 mA sink
0.8
V
1,9
current
0.4 < VI/O <
-10
+10
2
µA
0.9VDD
10
pF
1
3,4
µA
3,4
Active Temp.
1000
µA
Conversions
Communication
100
only
DC ELECTRICAL CHARACTERISTICS
PARAMETER
Input Logic High
Input Logic Low
SDA Output Logic Low
Voltage
SYMBOL
VIH
VIL
VOL1
VOL2
O.S. Saturation Voltage
VOL
Input current each I/O pin
I/O Capacitance
Standby Current
Active Current
CI/O
IDD1
IDD
ELECTRICAL CHARACTERISTICS:
DIGITAL THERMOMETER
PARAMETER
Thermometer Error
Resolution
Conversion Time
SYMBOL
TERR
tCONVT
(–55°C to +125°C; 2.7V ≤VDD ≤5.5V)
CONDITION
MIN
TYP MAX UNITS NOTES
9, 10
–10°C to +85°C
±2.0
°C
–55°C to 125°C
±3.0
9
12
bits
ms
9-bit
125
150
conversion
10-bit
250
300
conversion
11-bit
500
600
conversion
12-bit
1000
1200
conversion
11 of 13
102299
DS1775
AC ELECTRICAL CHARACTERISTICS:
2–WIRE INTERFACE
PARAMETER
SCL clock frequency
Bus free time between a
STOP and START
condition
Hold time (repeated)
START condition
LOW period of SCL
(–55°C to +125°C; VDD =2.7V to 5.5V)
SYMBOL CONDITION MIN TYP MAX UNITS NOTES
fSCL
Fast Mode
400
KHZ
Standard Mode
100
tBUF
Fast Mode
1.3
µs
Standard Mode
4.7
tHD:STA
tLOW
HIGH period of SCL
tHIGH
Set-up time for a
repeated START
Data hold time
tSU:STA
tHD:DAT
Data set-up time
tSU:DAT
Rise time of both SDA and
SCL signals
Fall time of both SDA and
SCL signals
Set-up time for STOP
Capacitive load for each bus
line
Input Capacitance
tR
tF
tSU:STO
Fast Mode
Standard Mode
Fast Mode
Standard Mode
Fast Mode
Standard Mode
Fast Mode
Standard Mode
Fast Mode
Standard Mode
Fast Mode
Standard Mode
Fast Mode
Standard Mode
Fast Mode
Standard Mode
Fast Mode
Standard Mode
µs
0.6
4.0
1.3
4.7
0.6
4.0
0.6
4.7
0
0
100
250
20+
0.1CB
20+
0.1CB
0.6
4.0
µs
µs
µs
0.9
0.9
300
1000
300
300
µs
6
ns
7
ns
8
ns
8
µs
Cb
400
CI
5
5
pF
8
pF
NOTES:
1.
2.
3.
4.
5.
6.
All voltages are referenced to ground.
I/O pins of fast mode devices must not obstruct the SDA and SCL lines if VDD is switched off.
IDD specified with O.S. pin open.
IDD specified with VCC at 5.0V and SDA, SCL = 5.0V, 0°C to +70°C.
After this period, the first clock pulse is generated.
The maximum tHD:DAT has only to be met if the device does not stretch the LOW period (tLOW ) of the
SCL signal.
7. A fast mode device can be used in a standard mode system, but the requirement tSU:DAT ≥ 250 ns must
then be met. This will automatically be the case if the device does not stretch the LOW period of the
SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next
data bit to the SDA line tR MAX +tSU:DAT = 1000+250 = 1250 ns before the SCL line is released.
8. Cb – total capacitance of one bus line in pF.
9. Internal heating caused by O.S. loading will cause the DS1775 to read approximately 0.5? C higher if
O.S. is sinking the max rated current.
10. Contact the factory in Dallas, (972) 371-4448, for operation requiring temperature readings greater
than 120°C.
12 of 13
102299
DS1775
TIMING DIAGRAMS Figure 6
13 of 13
102299