Type 167/184 Metallized Polyester Radial Lead Capacitors Radial Box Metallized Polyester Capacitors for Automatic Insertion The Type 167/184 series radial lead metallized polyester box capacitors are available in bulk (Type 167) or on ammo pack or radial tape and reel (Type 184). These capacitors are constructed in rugged rectangular plas tic cases and all come with 7.5 mm (0.3”) lead spacing. They are good for general purpose applications such as bypass, decoupling, energy storage/discharge and arc suppression. Highlights • • • • • • Rugged plastic case Case and epoxy fill meets UL94V0 7.5 mm (0.3”) lead spacing Bulk, tape and reel or ammo pack Non-inductively wound Non-polar Specifications RoHS Compliant Capacitance Range: Voltage Range: Capacitance Tolerance: Operating Temperature Range: Dielectric Withstand Voltage: Dissipation Factor (DF): 0.001 µF to 1.0 µF 63 Vdc to 630 Vdc (40 Vac to 250 Vac, 60 Hz) ±5%, ±10%, ±20% –55 ºC to +125 ºC (with 50% Vdc derating >85 ºC) 1.6 x rated voltage for 2 sec @ +25 ºC ±5 ºC tanδ x 10–4 at 25 ºC ±5 ºC kHz tanδ x 10–4 1 ≤100 10 ≤150 Total Self Inductance (L): Approximately 8 nH Maximum Pulse Rise Time (dv/dt): Vn V/µs 63 12 100 20 250 32 400 41 630 70 If the working voltage (V) is less than the nominal voltage (Vn), the capacitor can work at higher dv/dt. In this case, the maximum value allowed is obtained by multiplying the above value with the ratio Vn/V. Long Term Stability (after two years) Storage Standard Environmental Conditions Performance Capacitance Change ∆C/C ≤ ±3% CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com Type 167/184 Metallized Polyester Radial Lead Capacitors Capacitor Outline Drawing Test Method and Performance Insulation Resistance Test Conditions Temperature 25 ºC ±5 ºC 1 minute Voltage Charge Time Voltage Charge 50 Vdc for Vn < 100 Vdc 100 Vdc for Vn ≥ 100 Vdc Performance For Vn > 100 Vdc ≥30,000 MΩ (50,000 MΩ typical) For Vn ≤100 Vdc ≥10,000 MΩ for C ≤ 0.1µF ≥1,000 MΩ x µF for > 0.1µF Damp Heat Test Test Conditions Temperature +40 ºC Relative Humidity 95% 21 days Test Duration Performance Capacitance Change ∆C/C ≤ ±5% DF Change ∆tgδ ≤50 x 104 at 1 kHz Insulation Resistance ≥ 50% of limit value Life Test Test Conditions Temperature +85 ºC Test Duration 1000 hrs Voltage Applied 1.25 x Vn Performance Capacitance Change ∆C/C ≤ ±5% DF Change ∆tgδ ≤30 x 10–4 at 10 kHz Insulation Resistance ≥ 50% of limit value T L Max Max H Max .217 ±.039 (5.5 ±1.0 mm) S ±.015 (±0.4 mm) Ød ±.002 (±0.05) Lead length shown is as supplied on 167 Series Soldering Test Conditions Soldering Temperature 260 ºC ±5 ºC Soldering Duration 10 sec ±1 sec Performance Capacitance Change ∆C/C ≤ ±2% DF Change ∆tgδ ≤30 x 10–4 at 10 kHz Insulation Resistance ≥ limit value Ratings Cap (µF) RoHS Compliant Catalog Part Number Tape & Reel Ammo Pack Inches L T H Millimeters S Ød L T H S Ød 63 Vdc / 40 Vac .068 167683*63A–F 184683*63#A>–F 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6 .10 167104*63A–F 184104*63#A>–F 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6 .15 167154*63A–F 184154*63#A>–F 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6 .22 167224*63A–F 184224*63#A>–F 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6 .27 167274*63A–F 184274*63#A>–F 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6 .33 167334*63A–F 184334*63#A>–F 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6 .47 167474*63B–F 184474*63#B>–F 0.413 0.157 0.354 0.295 0.024 10.5 4.0 9.0 7.5 0.6 .68 167684*63C–F 184684*63#C>–F 0.413 0.197 0.433 0.295 0.024 10.5 5.0 11.0 7.5 0.6 1.00 167105*63C–F 184105*63#C>–F 0.413 0.197 0.433 0.295 0.024 10.5 5.0 11.0 7.5 0.6 100 Vdc / 63 Vac .033 167333*100A–F 184333*100#A>–F 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6 .047 167473*100A–F 184473*100#A>–F 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6 .068 167683*100A–F 184683*100#A>–F 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6 .10 167104*100A–F 184104*100#A>–F 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6 .12 167124*100B–F 184124*100#B>–F 0.413 0.157 0.354 0.295 0.024 10.5 4.0 9.0 7.5 0.6 .15 167154*100B–F 184154*100#B>–F 0.413 0.157 0.354 0.295 0.024 10.5 4.0 9.0 7.5 0.6 .22 167224*100C–F 184224*100#C>–F 0.413 0.197 0.433 0.295 0.024 10.5 5.0 11.0 7.5 0.6 .33 167334*100C–F 184334*100#C>–F 0.413 0.197 0.433 0.295 0.024 10.5 5.0 11.0 7.5 0.6 * Indicates capacitance tolerance: J = ±5%, K = ±10%, M = ±20% # Indicates packaging type: R = Tape and Reel, A = Ammo Pack > Indicates tooling code: A = 16.5 mm, B = 18.5 mm, C = 16.0 mm (See H dimension in taping specifications) CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com Type 167/184 Metallized Polyester Radial Lead Capacitors Cap (µF) Catalog Part Number Tape & Reel Ammo Pack Inches L T Millimeters H S Ød L T H S Ød 250 Vdc / 160 Vac .010 167103*250A–F 184103*250#A>–F 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6 .015 167153*250A–F 184153*250#A>–F 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6 .018 167183*250A–F 184183*250#A>–F 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6 .022 167223*250A–F 184223*250#A>–F 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6 .027 167273*250B–F 184273*250#B>–F 0.413 0.157 0.354 0.295 0.024 10.5 4.0 9.0 7.5 0.6 .033 167333*250B–F 184333*250#B>–F 0.413 0.157 0.354 0.295 0.024 10.5 4.0 9.0 7.5 0.6 .039 167393*250B–F 184393*250#B>–F 0.413 0.157 0.354 0.295 0.024 10.5 4.0 9.0 7.5 0.6 .047 167473*250B–F 184473*250#B>–F 0.413 0.157 0.354 0.295 0.024 10.5 4.0 9.0 7.5 0.6 .068 167683*250C–F 184683*250#C>–F 0.413 0.197 0.433 0.295 0.024 10.5 5.0 11.0 7.5 0.6 .100 167104*250C–F 184104*250#C>–F 0.413 0.197 0.433 0.295 0.024 10.5 5.0 11.0 7.5 0.6 400 Vdc / 200 Vac .0047 167472*400A–F 184472*400#A>–F 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6 .0056 167562*400A–F 184562*400#A>–F 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6 .0068 167682*400A–F 184682*400#A>–F 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6 .010 167103*400A–F 184103*400#A>–F 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6 .015 167153*400B–F 184153*400#B>–F 0.413 0.157 0.354 0.295 0.024 10.5 4.0 9.0 7.5 0.6 .022 167223*400C–F 184223*400#C>–F 0.413 0.197 0.433 0.295 0.024 10.5 5.0 11.0 7.5 0.6 .033 167333*400C–F 184333*400#C>–F 0.413 0.197 0.433 0.295 0.024 10.5 5.0 11.0 7.5 0.6 630 Vdc / 220 Vac .0010 167102*630A–F 184102*630#A>–F 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6 .0015 167152*630A–F 184152*630#A>–F 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6 .0022 167222*630A–F 184222*630#A>–F 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6 .0033 167332*630A–F 184332*630#A>–F 0.413 0.138 0.276 0.295 0.024 10.5 3.5 7.0 7.5 0.6 .0047 167472*630B–F 184472*630#B>–F 0.413 0.157 0.354 0.295 0.024 10.5 4.0 9.0 7.5 0.6 .0068 167682*630B–F 184682*630#B>–F 0.413 0.157 0.354 0.295 0.024 10.5 4.0 9.0 7.5 0.6 .010 167103*630C–F 184103*630#C>–F 0.413 0.197 0.433 0.295 0.024 10.5 5.0 11.0 7.5 0.6 .015 167153*630D–F 184153*630#D>–F 0.413 0.236 0.472 0.295 0.024 10.5 6.0 12.0 7.5 0.6 * Indicates capacitance tolerance: J = ±5%, K = ±10%, M = ±20% # Indicates packaging type: R = Tape and Reel, A = Ammo Pack > Indicates tooling code: A = 16.5 mm, B = 18.5 mm, C = 16.0 mm (See H dimension in taping specification) Part Numbering System for Bulk Items 167 Series 167 104 K Capacitance Tolerance 392 = .0039 µF J = ±5% 100 A -F Case RoHS Voltage Code Compliant 63 = 63 Vdc A Designator 103 = .01 µF K = ±10% 100 = 100 Vdc B 104 = .1 µF M = ±20% 250 = 250 Vdc C 630 = 630 Vdc D 105 = 1.0 µF CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com Type 167/184 Metallized Polyester Radial Lead Capacitors Tape Specification - 7.5 mm Lead Spacing 30 mm 1.18” Reel Packing ΔH P1 331 mm 13.04” Ammo Box Packing P Po 280 mm Max 11.02” Wo W W1 H W2 Ød Do 47 mm Max 1.85” Item Code Lead-Wire Diameter Ød Millimeters Inches 0.6+0.04 –0.01 .024±.001 Lead-to-Lead Distance P 7.5+0.6 –0.2 .295+.024 –.040 Feed Hole Pitch P0 2.7±0.3 .5±.012 Pitch of Component P1 12.7±1.0 .5±.039 Hole Center to Lead P2 8.95±0.7 .352±.028 Component Alignment, F-R ∆h 0±2.0 0±.079 Tape Width W 18+1.0 –0.1 .709+.039 –.004 Hold-down Tape Width W0 6.0 min .236 min Hole Position W1 9.0 .355+.030 –.001 Hold-down Tape Position W2 3.0 Max .118 Max H > Height of Component +0.75 –0.05 335 mm Max 13.19” Case Quantity Quantity Code Reeled Ammo Pack A 1800 1500 B 1500 1500 C 1200 1000 D 1000 1000 > The H dimension depends on the insertion equipment used. Specify the proper tooling code as indicated below. Tooling Millimeters Inches A 16.5±0.75 .679±.030 B 18.5±0.75 .728±.030 C 16.0 .630±030 > from Tape Center Feed Hole Diameter D0 4.0±0.3 H Dimensions Code .157±.012 ±0.75 Part Numbering System for Auto Insertion 184 104 K 100 R A Packaging Series Capacitance Tolerance 184 392 = .0039 µF J = ±5% B -F *Tooling RoHS Type Case Code Compliant Voltage (#) Code (>) Designator 63 = 63 Vdc A = Ammo A A R = Tape & Reel 103 = .01 µF K = ±10% 100 = 100 Vdc B B 104 = .1 µF M = ±20% 250 = 250 Vdc C C 630 = 630 Vdc D 105 = 1.0 µF * Tooling code is at the discretion of the user depending on the insertion equipment being used. See table for specific "H" dimensions * Tooling code (>) depends on the users insertion equipment requirements. See table for available options. CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com