METALIZED POLYPROPYLENE FILM CAPACITORS MPP Series: Radial Dipped RoHS INTRODUCTION MAX W MAX MPP series are constructed with metalized polypropylene film dielectric, copperply lead and flame retardant epoxy resin coating. The MPP series is smaller then the PMD series. Suitable blocking, by-pass, coupling, decoupling, filtering, timing, tuning, temperature compensation and ideal for use in ballasts, switching power supplies, telecommunication equipment, industrial instruments, automatic control systems and other general electronic equipment. H MAX D + 0.05 2 MAX 20 MIN P FEATURES (Can be box encapsulated. See MPB series.) •Low dissipation factor at high frequency •High capacitance and dissipation factor stability •Non-inductive construction •Self-healing •Flame retardant epoxy resin coating (compliant to UL 94V-0) SPECIFICATIONS Performance Items 100Vdc, 250Vdc, 400Vdc, 630Vdc Operating Voltage Range -40 ˚C ~ +85ºC Rated Temperature Usable Upper Category Temperature +105ºC (Derating ratio of rated voltage over +85˚C ~ +110º C: 1.5% per ºC of Rated Voltage) 0.01 µF ~ 10 µF Capacitance Range +3% (H), +5% (J), +10% (K) Capacitance Tolerance KHz C < 0.1 µF 0.1 < C < 1.0 µF 1.0 < C < 3.0 µF 3.0 < C < 5.0 µF Dissipation Factor 1 100 5.0 < C < 10 µF < 0.10% < 0.40% < 0.70% < 1.20% < 1.80% < 2.80% Voltage Charge: 100Vdc x 1min (at 20˚C + 5˚C) Insulation Resistance Terminal to Terminal > 30,000MΩ for C < 0.33µF > 10,000MΩ x µF for C > 0.33µF Terminal to Terminal: (at 20˚C + 5˚C) Withstand Voltage Pitch Rated Voltage Pulse Slope dV/dt (V/µs) VR 100Vdc 250Vdc 400Vdc 630Vdc 7.5mm 10mm 15mm 130 240 --- 110 220 350 420 100 200 300 400 22.5mm 70 130 200 250 27.5mm 50 100 150 180 RELIABILITY TEST Item Test Methods Resistance to Soldering Heat IEC 60068-2-20 Resistance to Vibration IEC 60068-2-6 Damp Heat, Steady State IEC 60068-2-3 Electrical Endurance IEC 60384-17 Solder Bath: 260ºC + 5ºC Immersion Time: 10sec + 1sec Frequency Range: 10Hz to 55Hz Amplitude: 1.5mm Duration: 6 hours Temperature: 40ºC + 2ºC Relative Humidity: 90% to 95% Duration: 1,000 hours Temperature: 85ºC + 2ºC Voltage Applied: 1.25 x Vr(DC) Duration: 2,000 hours Requirements Capacitance Change ІΔ C/C : <1% DF Change Δ tan δ : 0.1% at 1KHz IR: > limit value There shall be no Visible Damage, No Intermittent Contact, No Open or Short Circuit Capacitance Change ІΔC/C І< : 3% DF Change Δ tan δ: 0.1% at 1KHz IR: > 50% limit value Capacitance Change ІΔC/CІ< : 3% DF Change Δ tan δ : 0.1% at 1KHz IR: > 50% limit value Page 1 of 3 RFE International • Tel:(949) 833-1988 • Fax:(949) 833-1788 • E-Mail [email protected] C1DD03 2014.04.17 METALIZED POLYPROPYLENE FILM CAPACITORS MPP Series: Radial Dipped RoHS MAXIMUM DIMENSIONS W .V . (µF) 0.010 0.012 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.056 0.068 0.082 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.39 Code 100V DC (2A ) W H T 250V DC (2E ) P d W H T P 400V DC (2G) 630V DC (2J) d W H T P d W H T P d 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.8 0.8 0.8 10.5 10.5 10.5 10.5 10.5 10.5 10.5 13.0 13.0 13.0 13.0 13.0 13.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 7.5 8.5 9.0 9.5 10.0 10.5 11.0 11.0 11.0 11.5 12.5 13.0 13.5 12.0 12.5 13.5 15.0 16.0 17.0 18.0 4.0 4.0 4.5 4.5 5.0 5.5 6.0 5.5 5.5 6.0 6.5 7.0 8.0 6.0 7.0 8.5 8.0 8.5 9.5 10.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 10.0 10.0 10.0 10.0 10.0 10.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.8 0.8 0.8 0.8 0.8 0.8 0.8 10.5 10.5 10.5 10.5 13.0 13.0 13.0 13.0 13.0 13.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 25.5 25.5 25.5 20.5 25.5 25.5 25.5 25.5 26.0 31.5 31.5 9.0 9.5 10.5 11.0 10.0 11.0 11.5 12.0 13.0 14.0 12.5 13.0 14.0 15.5 16.5 17.5 18.5 18.0 19.0 20.0 20.5 21.0 22.5 24.0 25.5 16.5 25.0 27.0 5.5 6.0 6.0 6.5 6.0 6.5 7.0 8.0 8.0 9.0 7.0 7.5 8.0 8.0 9.0 10.0 11.5 9.0 10.0 11.0 12.0 12.0 13.5 15.0 16.5 12.0 16.0 18.0 7.5 7.5 7.5 7.5 10.0 10.0 10.0 10.0 10.0 10.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 22.5 22.5 22.5 17.5 22.5 22.5 22.5 22.5 22.5 27.5 27.5 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 103 123 153 183 223 273 333 393 473 563 683 823 104 124 154 184 224 274 334 394 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 13.0 13.0 13.0 13.0 0.47 474 13.0 14.0 8.5 10.0 0.6 18.0 15.0 8.0 0.56 0.68 0.82 564 684 824 18.0 14.0 7.0 18.0 15.0 7.5 18.0 15.5 8.0 15.0 0.8 18.0 16.0 8.5 15.0 0.8 25.5 17.0 10.0 22.5 0.8 15.0 0.8 18.0 17.0 9.5 15.0 0.8 25.5 18.0 11.0 22.5 0.8 15.0 0.8 18.0 18.5 10.0 15.0 0.8 25.5 20.0 11.0 22.5 0.8 1.00 105 18.0 16.5 9.0 15.0 0.8 18.0 20.0 11.0 15.0 0.8 25.5 21.5 12.5 22.5 0.8 1.20 1.50 1.80 2.20 2.70 3.30 125 155 185 225 275 335 18.0 18.0 25.5 25.5 25.5 25.5 15.0 15.0 22.5 22.5 22.5 22.5 7.5 8.0 9.0 9.5 10.0 10.0 11.0 11.5 11.5 12.0 13.0 13.5 17.5 18.5 18.0 19.0 20.0 24.5 4.0 4.0 4.5 4.5 5.0 5.5 6.0 6.5 6.0 6.5 7.0 7.5 10.0 11.5 9.0 10.0 11.5 15.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 10.0 10.0 10.0 10.0 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.8 0.8 0.8 0.8 0.8 0.8 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 13.0 13.0 13.0 13.0 18.0 18.0 18.0 25.5 25.5 25.5 25.5 25.5 25.5 7.5 8.0 8.5 9.0 10.0 10.5 11.0 11.5 12.0 11.5 12.0 12.5 13.0 13.0 14.0 14.5 18.0 19.5 20.5 22.0 23.5 25.5 4.0 4.0 4.5 4.5 4.5 5.0 5.5 6.0 6.5 6.0 6.5 7.0 7.5 6.0 6.5 7.0 9.0 10.5 11.5 13.0 14.5 16.0 PART NUMBER EXAMPLE - BULK 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 10.0 10.0 10.0 10.0 15.0 15.0 15.0 15.0 0.8 25.5 16.0 9.0 22.5 22.5 22.5 22.5 22.5 22.5 22.5 0.8 0.8 25.5 23.0 14.0 22.5 0.8 0.8 25.5 24.5 15.5 22.5 0.8 0.8 0.8 0.8 0.8 PART NUMBER EXAMPLE - RADIAL TAPED MPP 103 M 2G 075 B 100 S MPP 103 K 2G 075 A RT2 K Series Capacitance Tolerance Voltage Code Lead Spacing Code* Packaging Lead Length Lead Style Series Capacitance Tolerance Voltage Code Lead Spacing Code* Packaging Tape Code (Tape) Lead Style * Leadspace is straight lead non-formed original leadspace. CAPACITANCE µF 0.01 0.047 pF 10,000 47,000 Code 103 473 TOLERANCE CODE 0.1 100,000 104 0.47 1.0 3.3 – – 470,000 474 105 335 Code Tolerance J + 5% K + 10% M + 20% Page 2 of 3 RFE International • Tel:(949) 833-1988 • Fax:(949) 833-1788 • E-Mail [email protected] C1DD03 2014.04.17 METALIZED POLYPROPYLENE FILM CAPACITORS MPP Series: Radial Dipped RoHS LEAD STYLE EXAMPLES TAPE CODE (See Diagrams) RATED VOLTAGE W.V. 100 250 400 630 Code 2A 2E 2G 2J Spacing Packing Code RADIAL LEAD SPACING 7.5mm A or R RT2 10mm 15mm A A RT3 RT4 LEAD LENGTH FROM SEATING PLANE (if bulk pack) * Leadspace is straight lead non-formed original leadspace. mm 7.5 10 15 22.5 27.5 Code 075 100 150 225 275 mm 5 10 15 20 Code K Code S 2mm max 5mm max LL+1mm LL+1mm Code F Code I 25 Code 050 100 150 200 250 5mm max 5mm max LL+1mm LL+1mm (For LL over 20mm spec is minimum) PACKAGING LEAD STYLE Code S K F I Method Bulk Ammo Reel Code B A R RADIAL TAPING CODE DIAGRAM Style Straight Kink-In (Stand Off) Form Out Form In P P2 Δh P2 t P Δh P1 W1 t d P1 W H W2 W1 W F W2 PO Do PO Fig. 2 F=7.5mm (RT2) WO F d HH W0 Do Fig. 1 F=7.5mm (RT2) P P2 Δh t P1 d H P1 W1 W W0 W W2 Do W2 PO Fig. 4 Box or Epoxy Coated F=10 - Ammo Only F=15 Every other space skipped because of Larger body - Ammo Only (RT3 or RT4) SPECIFICATIONS Dimension (mm) Dimension (mm) Letter Description Lead Wire Diameter d Tape Pitch RT2 0.5 / 0.6 0.5 / 0.6 Do PO F Fig. 3 Box Fitch=7.5mm Ammo Only (RT2) RT1 d HH W1 WO F Description P Δh t RT3 RT4 Tol. 0.6 0.6 / 0.8 + 0.05 Carrier Tape Width Letter W RT1 RT2 18 18 RT3 RT4 18 18 Tol. + 1; -0.5 P 12.7 12.7 12.7 25.4 +1 Hold Down Tape Width WO 6 6 9 10 Min Feed Hole Pitch PO 12.7 12.87 12.7 12.7 + 0.2 Hole Position W1 9 9 9 9 + 0.5 Centering of the Lead Wire P1 3.85 2.6 / 3.75 7.7 5.2 + 0.7 Hold Down Tape Position W2 3 3 3 3 Max Centering of the Body P2 6.35 6.35 12.7 12.7 + 1.3 Feed Hole Diameter Do 4 4 4 4 + 0.2 Lead Spacing (Pitch) F 5 7.5 10 15 t 0.7 0.7 Component Alignment ∆h 0 0 0 0 +2 Height of Componenet from Tape Center H 18.5 18.5 18.5 18.5 + 0.5 + 0.6; -0.1 Tape Thickness Figure fig 1 or 2 1.2 or 3 0.7 0.07 4 + 0.2 4 Remark: *Allowance of accumulated pitch less than 1mm at the sum of 20 pitches. Remark: *Continuous empty component less than 3 consecutive pieces. Remark: *Total empty on one reel less than 1%. Page 3 of 3 RFE International • Tel:(949) 833-1988 • Fax:(949) 833-1788 • E-Mail [email protected] C1DD03 2014.04.17