ELPIDA EBE51FD8AGFD-5C-E

PRELIMINARY DATA SHEET
512MB Fully Buffered DIMM
EBE51FD8AGFD
EBE51FD8AGFN
Specifications
Features
• Density: 512MB
• Organization
 64M words × 72 bits, 1 rank
• Mounting 9 pieces of 512M bits DDR2 SDRAM
sealed in FBGA
• Package
 240-pin fully buffered, socket type dual in line
memory module (FB-DIMM)
PCB height: 30.35mm
Lead pitch: 1.00mm
 Advanced Memory Buffer (AMB): 655-ball FCBGA
 Lead-free (RoHS compliant)
• Power supply
 DDR2 SDRAM: VDD = 1.8V ± 0.1V
 AMB: VCC = 1.5V + 0.075V/−0.045
• Data rate: 667Mbps/533Mbps (max.)
• Four internal banks for concurrent operation
(components)
• Interface: SSTL_18
• Burst lengths (BL): 4, 8
• /CAS Latency (CL): 3, 4, 5
• Precharge: auto precharge option for each burst
access
• Refresh: auto-refresh, self-refresh
• Refresh cycles: 8192 cycles/64ms
 Average refresh period
7.8µs at 0°C ≤ TC ≤ +85°C
3.9µs at +85°C < TC ≤ +95°C
• Operating case temperature range
 TC = 0°C to +95°C
• JEDEC standard Raw Card A Design
• Industry Standard Advanced Memory Buffer (AMB)
• High-speed differential point-to-point link interface at
1.5V (JEDEC draft spec)
 14 north-bound (NB) high speed serial lanes
 10 south-bound (SB) high speed serial lanes
• Various features/modes:
 MemBIST and IBIST test functions
 Transparent mode and direct access mode for
DRAM testing
 Interface for a thermal sensor and status indicator
• Channel error detection and reporting
• Automatic DDR2 SDRAM bus and channel
calibration
• SPD (serial presence detect) with 1piece of 256 byte
serial EEPROM
Note: Warranty void if removed DIMM heat
spreader.
Performance
FB-DIMM
System clock
frequency
DDR2 SDRAM
Speed grade
Peak channel
throughput
FB-DIMM link data rate
Speed Grade
DDR data rate
167MHz
PC2-5300F
8.0GByte/s
4.0Gbps
DDR2-667 (5-5-5)
667Mbps
133MHz
PC2-4200F
6.4GByte/s
3.2Gbps
DDR2-533 (4-4-4)
533Mbps
Document No. E0869E30 (Ver. 3.0)
Date Published August 2006 (K) Japan
Printed in Japan
URL: http://www.elpida.com
Elpida Memory, Inc. 2006
EBE51FD8AGFD, EBE51FD8AGFN
Ordering Information
Part number
DIMM speed
grade
Component JEDEC
speed bin (CL-tRCD-tRP)
Package
EBE51FD8AGFD-6E-E
PC2-5300F
DDR2-667 (5-5-5)
240-pin FB-DIMM EDE5108AGSE-6E-E
EBE51FD8AGFD-5C-E
PC2-4200F
DDR2-533 (4-4-4)
EDE5108AGSE-6E-E
EDE5108AGSE-5C-E
EBE51FD8AGFN-6E-E
PC2-5300F
DDR2-667 (5-5-5)
240-pin FB-DIMM EDE5108AGSE-6E-E
EBE51FD8AGFN-5C-E
PC2-4200F
DDR2-533 (4-4-4)
EDE5108AGSE-6E-E
EDE5108AGSE-5C-E
Mounted devices*
Note: Please refer to the EDE5104AGSE, EDE5108AGSE datasheet (E0715E) for detailed operation part and
timing waveforms
Part Number
E B E 51 F D 8 A G F D - 6E - E
Environment code
E: Lead Free
(RoHS compliant)
Elpida Memory
Type
B: Module
DRAM Speed Grade
6E: DDR2-667 (5-5-5)
5C: DDR2-533 (4-4-4)
Product Family
E: DDR2
Density / Rank
51: 512MB/1-rank
AMB Device Information
D: Integrated Device Technology, Inc.
N: Intel Corporation
Module Type
F: Fully Buffered
Mono Density
D: 512Mbit
Module Outline
F: 240-pin DIMM
Mono Organization
8: x8
Die Rev. (Mono)
Power Supply, Interface
A: 1.8V, SSTL_1.8
Preliminary Data Sheet E0869E30 (Ver. 3.0)
2
EBE51FD8AGFD, EBE51FD8AGFN
Advanced Memory Buffer Overview
The Advanced Memory Buffer (AMB) reference design complies with the FB-DIMM Architecture and Protocol
Specification. It supports DDR2 SDRAM main memory. The AMB allows buffering of memory traffic to support large
memory capacities. All memory control for the DRAM resides in the host, including memory request initiation, timing,
refresh, scrubbing, sparing, configuration access, and power management. The AMB interface is responsible for
handling FB-DIMM channel and memory requests to and from the local DIMM and for forwarding requests to other
DIMMs on the FB-DIMM channel.
The FB-DIMM provides a high memory bandwidth, large capacity channel solution that has a narrow host interface.
FB-DIMMs use commodity DRAMs isolated from the channel behind a buffer on the DIMM. The memory capacity is
288 devices per channel and total memory capacity scales with DRAM bit density.
The AMB is the buffer that isolates the DRAMs from the channel.
Advanced Memory Buffer Functionality
The AMB will perform the following FB-DIMM channel functions.
• Supports channel initialization procedures as defined in the initialization chapter of the FB-DIMM Architecture and
Protocol Specification to align the clocks and the frame boundaries, verify channel connectivity, and identify AMB
DIMM position.
• Supports the forwarding of southbound and northbound frames, servicing requests directed to a specific AMB or
DIMM, as defined in the protocol chapter, and merging the return data into the northbound frames.
• If the AMB resides on the last DIMM in the channel, the AMB initializes northbound frames.
• Detects errors on the channel and reports them to the host memory controller.
• Support the FB-DIMM configuration register set as defined in the register chapters.
• Acts as DRAM memory buffer for all read, write, and configuration accesses addressed to the DIMM.
• Provides a read buffer FIFO and a write buffer FIFO.
• Supports an SMBus protocol interface for access to the AMB configuration registers.
• Provides logic to support MemBIST and IBIST design for test functions.
• Provides a register interface for the thermal sensor and status indicator.
• Functions as a repeater to extend the maximum length of FB-DIMM links.
Preliminary Data Sheet E0869E30 (Ver. 3.0)
3
EBE51FD8AGFD, EBE51FD8AGFN
Advanced Memory Buffer Block Diagram
Southbound
10×2
Data in
Reference
clock
Southbound
Data out
10×2
Data merge
PLL
RE-time
1×2
Re-synch
PISO
Demux
/RESET
Reset
control
10×12
10×12
Link init SM
and control
and CSRs
Thermal
sensor
Init
patterns
Mux
4
IBIST-RX
failover
Command
decoder &
CRC check
DRAM clock
IBIST-TX
4
DRAM clock
LAI logic
DRAM Command
Mux
Command
out
DRAM
interface
DDR state controller
and CSRs
Core
controller
and CSRs
Write data
FIFO
Mux
DRAM
address and
command copy1
29
DRAM
address and
command copy2
72+18×2
External MemBIST
DDR calibration
IBIST-TX
LAI
controller
Data in
Sync & idle
pattern
generator
Data CRC
generator and
Read FIFO
SMBus
Data out
29
Mux
IBIST-RX
Link init SM
and control
and CSRs
failover
14×6×2
SMBus
controller
NB LAI Buffer
14×12
PISO
Demux
Re-synch
RE-time
Data merge
Northbound 14×2
Data Out
14×2 Northbound
Data In
Note: This figure is a conceptual block diagram of the AMB’s data flow and clock domains.
Preliminary Data Sheet E0869E30 (Ver. 3.0)
4
DRAM
data and strobes
EBE51FD8AGFD, EBE51FD8AGFN
Interfaces
Figure Block Diagram AMB Interfaces shows the AMB and all of its interfaces. They consist of two FB-DIMM links,
one DDR2 channel and an SMBus interface. Each FB-DIMM link connects the AMB to a host memory controller or
an adjacent FB-DIMM. The DDR2 channel supports direct connection to the DDR2 SDRAMs on a FB-DIMM.
NB FBD
in Link
NB FBD
out Link
SB FBD
in Link
AMB
SB FBD
out Link
Secondary or to
optional next FBD
Primary or Host
Direction
Memory Interface
SMB
Block Diagram AMB Interfaces
Interface Topology
The FB-DIMM channel uses a daisy-chain topology to provide expansion from a single DIMM per channel to up to 8
DIMMs per channel. The host sends data on the southbound link to the first DIMM where it is received and redriven
to the second DIMM. On the southbound data path each DIMM receives the data and again re-drives the data to the
next DIMM until the last DIMM receives the data. The last DIMM in the chain initiates the transmission of data in the
direction on the host (a.k.a. northbound). On the northbound data path each DIMM receives the data and re-drives
the data to the next DIMM until the host is reached.
Host
Nourthbound
Southbound
AMB
AMB
AMB
AMB
n/c
n/c
Block Diagram FB-DIMM Channel Southbound and Northbound Paths
Preliminary Data Sheet E0869E30 (Ver. 3.0)
5
EBE51FD8AGFD, EBE51FD8AGFN
High-Speed Differential Point-to-Point Link (at 1.5 V) Interfaces
The AMB supports one FB-DIMM channel consisting of two bidirectional link interfaces using high-speed differential
point-to-point electrical signaling. The southbound input link is 10 lanes wide and carries commands and write data
from the host memory controller or the adjacent DIMM in the host direction. The southbound output link forwards
this same data to the next FB-DIMM. The northbound input link is 14 lanes wide and carries read return data or
status information from the next FB-DIMM in the chain back towards the host. The northbound output link forwards
this information back towards the host and multiplexes in any read return data or status information that is generated
internally. Data and commands sent to the DRAMs travel southbound on 10 primary differential signal line pairs.
Data received from the DRAMs and status information travel northbound on 14 primary differential pairs. Data and
commands sent to the adjacent DIMM upstream are repeated and travel further southbound on 10 secondary
differential pairs. Data and status information received from the adjacent DIMM upstream travel further northbound
on 14 secondary differential pairs.
DDR2 Channel
The DDR2 channel on the AMB supports direct connection to DDR2 SDRAMs. The DDR2 channel supports two
ranks of eight banks with 16 row/column request, 64 data, and eight check-bit signals. There are two copies of
address and command signals to support DIMM routing and electrical requirements. Four transfer bursts are driven
on the data and check-bit lines at 800MHz. Propagation delays between read data/check-bit strobe lanes on a given
channel can differ. Each strobe can be calibrated by hardware state machines using write/read trial and error.
Hardware aligns the read data and check-bits to a single core clock. The AMB provides four copies of the command
clock phase references (CLK [3:0]) and write data/check-bit strobes (DQSs) for each DRAM nibble.
SMBus Slave interface
The AMB supports an SMBus interface to allow system access to configuration register independent of the FB-DIMM
link. The AMB will never be a master on the SMBus, only a slave. Serial SMBus data transfer is supported at
100kHz. SMBus access to the AMB may be a requirement to boot and to set link strength, frequency and other
parameters needed to insure robust configurations. It is also required for diagnostic support when the link is down.
The SMBus address straps located on the DIMM connector are used by the unique ID.
Preliminary Data Sheet E0869E30 (Ver. 3.0)
6
EBE51FD8AGFD, EBE51FD8AGFN
Block Diagram
/CS0
/DQS4
/DQS0
DQS4
DQS0
NU/ /CS
/RDQS
DM/
RDQS
DQS9
DQ0 to DQ7
8
NU/ /CS
/RDQS
DQS /DQS
DQS13
D0
DQ0
to DQ7
8
DQS14
D1
DQ0
to DQ7
DQS6
DM/
RDQS
DQS11
8
NU/ /CS
/RDQS
DQS /DQS
DM/
RDQS
DQS15
D2
DQ0
to DQ7
8
DQ48 to DQ55
DQS /DQS
D6
DQ0
to DQ7
/DQS7
/DQS3
DQS7
DQS3
NU/ /CS
/RDQS
DM/
RDQS
DQS12
8
NU/ /CS DQS /DQS
/RDQS
DM/
RDQS
DQS /DQS
DQS16
D3
8
DQ56 to DQ63
DQ0
to DQ7
D7
DQ0
to DQ7
/DQS8
PN0 to PN13
/PN0 to /PN13
PS0 to PS9
/PS0 to /PS9
SCK/ /SCK
DQS /DQS
D5
/DQS6
NU/ /CS
/RDQS
/RESET
8
DQ40 to DQ47
DQ0
to DQ7
DQS2
SCL
SDA
SA0 to SA2
NU/ /CS
/RDQS
DM/
RDQS
DQS /DQS
/DQS2
DQ0 to DQ63
CB0 to CB7
DQS0 to DQS17
/DQS0 to /DQS8
D4
DQ0
to DQ7
DQS5
NU/ /CS
/RDQS
DM/
RDQS
DQS10
DQ24 to DQ31
DQS /DQS
/DQS5
DQS1
DQ16 to DQ23
8
DQ32 to DQ39
/DQS1
DQ8 to DQ15
DM/
RDQS
SN0 to SN13
/SN0 to /SN13
SS0 to SS9
/SS0 to /SS9
A
M
B
DQS8
DQS17
/CS0 -> /CS (all SDRAMs)
CKE0 -> CKE (all SDRAMs)
All address/command/control/clock
VTT
8
CB0 to CB7
ODT -> ODT (all SDRAMs)
BA0, BA1 (all SDRAMs)
A0 to A13 (all SDRAMs)
/RAS (all SDRAMs)
/CAS (all SDRAMs)
/WE (all SDRAMs)
CK/ /CK
NU/ /CS
/RDQS
DM/
RDQS
DQS /DQS
D8
DQ0
to DQ7
Serial PD
SCL
SDA
U0
SDA
WP A0
A1
A2
SA0 SA1 SA2
* D0 to D8 : 512M bits DDR2 SDRAM
Notes:
U0 : 256 bytes EEPROM
1. DQ wiring may be changed within a byte.
2. There are two physical copies of each address/command/control/clock
Preliminary Data Sheet E0869E30 (Ver. 3.0)
7
VTT
Teminators
VCC
AMB
VDDSPD
VDD
VREF
VSS
SPD, AMB
D0 to D8, AMB
D0 to D8
D0 to D8, SPD, AMB
EBE51FD8AGFD, EBE51FD8AGFN
Pin Configurations
Front side
1 pin
121 pin
68 pin 69 pin
120 pin
188 pin 189 pin
240 pin
Back side
Front side
Back side
No.
Name
No. Name
No.
Name
No.
Name
No.
Name
No.
Name
No.
Name No.
Name
1
VDD
36
VSS
71
/PS0
106
NC
121
VDD
156
VSS
191
/SS0
226
NC
2
VDD
37
PN5
72
VSS
107
VSS
122
VDD
157
SN5
192
VSS
227
VSS
3
VDD
38
/PN5
73
PS1
108
VDD
123
VDD
158
/SN5
193
SS1
228
SCK
4
VSS
39
VSS
74
/PS1
109
VDD
124
VSS
159
VSS
194
/SS1
229
/SCK
5
VDD
40
PN13
75
VSS
110
VSS
125
VDD
160
SN13
195
VSS
230
VSS
6
VDD
41
/PN13
76
PS2
111
VDD
126
VDD
161
/SN13
196
SS2
231
VDD
7
VDD
42
VSS
77
/PS2
112
VDD
127
VDD
162
VSS
197
/SS2
232
VDD
8
VSS
43
VSS
78
VSS
113
VDD
128
VSS
163
VSS
198
VSS
233
VDD
9
VCC
44
NC
79
PS3
114
VSS
129
VCC
164
NC
199
SS3
234
VSS
10
VCC
45
NC
80
/PS3
115
VDD
130
VCC
165
NC
200
/SS3
235
VDD
11
VSS
46
VSS
81
VSS
116
VDD
131
VSS
166
VSS
201
VSS
236
VDD
12
VCC
47
VSS
82
PS4
117
VTT
132
VCC
167
VSS
202
SS4
237
VTT
13
VCC
48
PN12
83
/PS4
118
SA2
133
VCC
168
SN12
203
/SS4
238
VDDSPD
14
VSS
49
/PN12
84
VSS
119
SDA
134
VSS
169
/SN12
204
VSS
239
SA0
15
VTT
50
VSS
85
VSS
120
SCL
135
VTT
170
VSS
205
VSS
240
SA1
16
VID1
51
PN6
86
NC
136
VID0
171
SN6
206
NC
17
/RESET 52
/PN6
87
NC
137
M_TEST 172
/SN6
207
NC
18
VSS
53
VSS
88
VSS
138
VSS
173
VSS
208
VSS
19
NC
54
PN7
89
VSS
139
NC
174
SN7
209
VSS
20
NC
55
/PN7
90
PS9
140
NC
175
/SN7
210
SS9
21
VSS
56
VSS
91
/PS9
141
VSS
176
VSS
211
/SS9
22
PN0
57
PN8
92
VSS
142
SN0
177
SN8
212
VSS
23
/PN0
58
/PN8
93
PS5
143
/SN0
178
/SN8
213
SS5
24
VSS
59
VSS
94
/PS5
144
VSS
179
VSS
214
/SS5
25
PN1
60
PN9
95
VSS
145
SN1
180
SN9
215
VSS
26
/PN1
61
/PN9
96
PS6
146
/SN1
181
/SN9
216
SS6
27
VSS
62
VSS
97
/PS6
147
VSS
182
VSS
217
/SS6
28
PN2
63
PN10
98
VSS
148
SN2
183
SN10
218
VSS
29
/PN2
64
/PN10
99
PS7
149
/SN2
184
/SN10
219
SS7
30
VSS
65
VSS
100
/PS7
150
VSS
185
VSS
220
/SS7
31
PN3
66
PN11
101
VSS
151
SN3
186
SN11
221
VSS
32
/PN3
67
/PN11
102
PS8
152
/SN3
187
/SN11
222
SS8
33
VSS
68
VSS
103
/PS8
153
VSS
188
VSS
223
/SS8
34
PN4
69
VSS
104
VSS
154
SN4
189
VSS
224
VSS
35
/PN4
70
PS0
105
NC
155
/SN4
190
SS0
225
NC
Preliminary Data Sheet E0869E30 (Ver. 3.0)
8
EBE51FD8AGFD, EBE51FD8AGFN
Pin Description
Pin name
Pin Type
Function
SCK, /SCK
Input
System clock input
PN0 to PN13, /PN0 to /PN13
Output
Primary northbound data
PS0 to PS9, /PS0 to /PS9
Input
Primary southbound data
SN0 to SN13, /SN0 to /SN13
Input
Secondary northbound data
SS0 to SS9, /SS0 to /SS9
Output
Secondary southbound data
SCL
Input
Serial presence detect (SPD) clock input
Input / Output
SPD data and AMB SMBus address/data
Input
SPD address inputs
Input
Voltage ID
SDA
SA0 to SA2*
1
VID0 to VID1*
/RESET
M_TEST*
NC
3
2
Input
AMB reset signal
Input
VREF margin test input

No connection
VCC
Power supply
AMB core power and AMB channel interface power (1.5V)
VDD
Power supply
DRAM power and AMB DRAM I/O power (1.8V)
VTT
Power supply
DRAM address, Command and clock termination voltage (VDD/2)
VDDSPD
Power supply
SPD power (3.3V)
VSS

Ground
Notes: 1. They are also used to select the DIMM number in the AMB.
2. These pins must be unconnected.
3. Don’t connect in a system.
Preliminary Data Sheet E0869E30 (Ver. 3.0)
9
EBE51FD8AGFD, EBE51FD8AGFN
Electrical Specifications
• All voltages are referenced to VSS (GND).
Absolute Maximum Ratings
Parameter
Symbol
Value
Unit
Voltage on any pin relative to VSS
VIN/VOUT
–0.3 to +1.75
V
AMB core power voltage relative to VSS
VCC
–0.3 to +1.75
V
DRAM interface power voltage relative to VSS
VDD
–0.5 to +2.30
V
Termination voltage relative to VSS
VTT
–0.5 to +2.30
V
Storage temperature
Tstg
–55 to +100
°C
Note
Caution
Exposing the device to stress above those listed in Absolute Maximum Ratings could cause
permanent damage. The device is not meant to be operated under conditions outside the limits
described in the operational section of this specification. Exposure to Absolute Maximum Rating
conditions for extended periods may affect device reliability.
Operating Temperature Conditions
Parameter
Symbol
Value
Unit
Note
SDRAM component case temperature
TC_DRAM
0 to +95
°C
1
AMB component case temperature
TC_AMB
110
°C
Note: 1. Supporting 0°C to +85°C and being able to extend to +95°C with doubling auto-refresh commands in
frequency to a 32ms period (tREFI = 3.9µs) and higher temperature self-refresh entry via the control of
EMRS (2) bit A7 is required.
DC Operating Conditions
Parameter
Symbol
min.
typ.
max.
Unit
Note
AMB supply voltage
VCC
1.455
1.50
1.575
V
DDR2 SDRAM supply voltage
VDD
1.7
1.8
1.9
V
Input termination voltage
VTT
0.48 × VDD
0.50 × VDD
0.52 × VDD
V
EEPROM supply voltage
VDDSPD
3.0
3.3
3.6
V
SPD input high voltage
VIH (DC)
2.1
—
VDDSPD
V
1
SPD input low voltage
VIL (DC)
—
—
0.8
V
1
RESET input high voltage
VIH (DC)
1.0
—
—
V
2
RESET input low voltage
VIL (DC)
—
—
0.5
V
2
Leakage current (RESET)
IL
–90
—
90
µA
2
Leakage current (link)
IL
–5
—
5
µA
3
Notes: 1. Applies for SMB and SPD bus signals.
2. Applies for AMB CMOS signal /RESET.
3. For all other AMB related DC parameters, please refer to the high-speed differential link interface
specification.
Preliminary Data Sheet E0869E30 (Ver. 3.0)
10
EBE51FD8AGFD, EBE51FD8AGFN
AMB Component Timing
For purposes of IDD testing, the following parameters are to be utilized.
Parameter
Symbol
min.
typ.
max.
Units
EI Assertion pass-thru timing
tEI
propagate
—
—
4
clks
EI deassertion pass-thru timing
tEID
—
—
bit lock
clks
EI assertion duration
tEI
100
—
—
clks
Resample pass-thru time
—
TBD
—
ns
Resynch pass-thru Time
—
TBD
—
ns
Bit lock Interval
tBitLock
—
—
119
frames
Frame lock Interval
tFrameLock
—
—
154
frames
Note
Note: 1. The EI stands for ″Electrical Idle″.
Power Specification Parameter and Test Conditions
Frequency (Mbps)
Parameter
Idle Current,
single or last
DIMM
Idle Current, first
DIMM
Active Power
Symbol
Idd_Idle_0
Idd_Idle_1
Idd_Active_1
Active Power,
Idd_Active_2
data pass through
Training
-6E
-5C
667
533
Power
Supply
max.
max.
Unit
Conditions
@1.5V
2.60
2.20
A
@1.8V
1.02
0.95
A
Total
5.37
4.62
W
L0 state, idle (0 BW)
Primary channel enabled,
Secondary channel disabled
CKE high. Command and address lines
stable.
DRAM clock active.
@1.5V
3.40
3.00
A
@1.8V
1.02
0.95
A
Total
6.63
5.88
W
@1.5V
3.90
3.40
A
@1.8V
2.65
2.71
A
Total
10.52
9.85
W
@1.5V
3.70
3.20
A
@1.8V
1.02
0.95
A
Total
7.11
6.19
W
@1.5V
4.00
3.50
A
0.99
0.91
A
7.53
6.58
W
Idd_Training
(for AMB spec. @1.8V
Not in SPD)
Total
Preliminary Data Sheet E0869E30 (Ver. 3.0)
11
L0 state, idle (0 BW)
Primary and secondary channels enabled
CKE high. Command and address lines
stable.
DRAM clock active.
L0 state
50% DRAM BW, 67% read, 33% write.
Primary and secondary channels enabled.
DRAM clock active, CKE high.
L0 state
50% DRAM BW to downstream DIMM,
67% read, 33% write.
Primary and secondary channels enabled.
CKE high. Command and address lines
stable.
DRAM clock active.
Primary and secondary channels enabled.
100% toggle on all channel lanes
DRAMs idle. 0 BW.
CKE high, Command and address lines
stable.
DRAM clock active.
Note
EBE51FD8AGFD, EBE51FD8AGFN
Reference Clock Input Specifications*1
Parameter
Reference clock frequency@ 3.2Gb/s
(nominal 133.33MHz)
Reference clock frequency@ 4.0 Gb/s
(nominal 166.67MHz)
Single-ended maximum voltage
Symbol
min.
max.
Units
Notes
fRefclk-3.2
126.67
133.40
MHz
2, 3, 4
fRefclk-4.0
158.33
166.75
MHz
2, 3, 4
Vmax

1.15
V
5, 7
Single-ended minimum voltage
Vmin
−0.3

V
5, 8
Differential voltage high
VRefclk-diff-ih
150

mV
6
Differential voltage low
VRefclk-diff-il

−150
mV
6
Absolute crossing point
VCross
250
550
mV
5, 9, 10
VCross variation
VCross-delta

140
mV
5, 9, 11
AC common mode
VSCK-cm-acp-p

225
mV
12
Rising and falling edge rates
ERRefclk-diff-Rise,
ERRefclk-diff-Fall
0.6
4.0
V/ns
6, 13
% Mismatch between rise and fall edge
rates
ERRefclk-Match

20
%
6, 14
Duty cycle of reference clock
TRefclk-Dutycycle
40
60
%
6
Ringback voltage threshold
VRB-diff
−100
100
mV
6, 15
Allowed time before ringback
TStable
500

ps
6, 15
Clock leakage current
II_CK
−10
10
µA
16, 17
Clock input capacitance
CI_CK
0.5
2.0
pF
17
Clock input capacitance delta
CI_CK (∆)
−0.25
0.25
pF
Difference between
RefClk and RefClk#
input capacitance
Transport delay
TD

NSAMPLE
10
Reference clock jitter (rms), filtered
5
ns
18, 19

periods
20
3.0
ps
21, 22

30
ps

TBD
ps
12
TREF-JITTER-RMS 
Reference clock jitter (peak-to-peak) due
TREF-SSCp-p
to spectrum clocking effects
Reference clock jitter difference between TREF-JITTERadjacent AMB
DELTA
Notes: 1. For details, refer to the JEDEC specification “FB-DIMM High Speed Differential PTP Link at 1.5V”.
2. The nominal reference clock frequency is determined by the data frequency of the link divided by 2 times
the fixed PLL multiplication factor for the FB-DIMM channel (6:1). fdata = 2000MHz for a 4.0Gbps FBDIMM channel and so on.
3. Measured with SSC disabled. Enabling SSC will reduce the reference clock frequency.
4. Not all FB-DIMM agents will support all frequencies; compliance to the frequency specifications is only
required for those data rates that are supported by the device under test.
5. Measurement taken from single-ended waveform.
6. Measurement taken from differential waveform.
7. Defined as the maximum instantaneous voltage including overshoot.
8. Defined as the minimum instantaneous voltage including undershoot.
9. Measured at the crossing point where the instantaneous voltage value of the rising edge of REFCLK+
equals the falling edge of REFCLK-.
10. Refers to the total variation from the lowest crossing point to the highest, regardless of which edge is
crossing. Refers to all crossing points for this measurement.
11. Defined as the total variation of all crossing voltages of rising REFCLK+ and falling REFCLK-. This is the
maximum allowed variance in for any particular system.
12. The majority of the reference clock AC common mode occurs at high frequency (i.e., the reference clock
frequency).
Preliminary Data Sheet E0869E30 (Ver. 3.0)
12
EBE51FD8AGFD, EBE51FD8AGFN
13. Measured from −150mV to + 150mV on the differential waveform. The signal must be monotonic through
the measurement region for rise and fall time. The 300mV measurement window is centered on the
differential 0V crossing.
14. Edge rate matching applies to rising edge rate for REFCLK+ and falling edge rate for REFCLK-. It is
measured using a ± 75mV window centered on the median cross point where REFCLK+ rising meets
REFCLK- falling. The median crosspoint is used to calculate the voltage thresholds the oscilloscope uses
for the edge rate calculations. The rising edge rate of REFCLK+ should be compared to the falling edge
rate of REFCLK-. The maximum allowed difference should not exceed 20% of the slowest edge
15. Tstable is the time the differential clock must maintain a minimum ±150mV differential voltage after rising
/falling edges before it is allowed to droop back into the ±100mV differential range.
16.Measured with a single-ended input voltage of 1V.
17. Applies to RefClk and RefClk#.
18. This parameter is not a direct clock output parameter but it indirectly determines the clock output
parameter TREF-JITTER.
19. The net transport delay is the difference in time of flight between associated data and clock paths. The
data path is defined from the reference clock source, through the TX, to data arrival at the data sampling
point in the RX. The clock path is defined from the reference clock source to clock arrival at the same
sampling point. The path delays are caused by copper trace routes, on-chip routing, on-chip buffering,
etc. They include the time-of-flight of interpolators or other clock adjustment mechanisms. They do not
include the phase delays caused by finite PLL loop bandwidth because these delays are modeled by the
PLL transfer functions.
20. Direct measurement of phase jitter records over NSAMPLE periods may be impractical. It is expected that
the jitter will be measured over a smaller, yet statistically significant, sample size and the total jitter at
NSAMPLE samples extrapolated from an estimate of the sigma of the random jitter components.
21. Measured with SSC enabled on reference clock generator.
22. As “measured” after the phase jitter filter. This number is separate from the receiver jitter budget that is
defined by the TRX-Total-MIN parameters.
Preliminary Data Sheet E0869E30 (Ver. 3.0)
13
EBE51FD8AGFD, EBE51FD8AGFN
Differential Transmitter Output Specifications*1
Parameter
Differential peak-to-peak
output voltage for large
voltage swing
Differential peak-to-peak
output voltage for regular
voltage swing
Differential peak-to-peak
output voltage for small
voltage swing
Symbol
min.
max.
Unit
Comments
VTX-DIFFp-p_L
900
1300
mV
VTX-DIFFp-p = 2 × | VTX-D+ − VTX-D- |
Measured as note 2
VTX-DIFFp-p_R
800

mV
VTX-DIFFp-p = 2 × | VTX-D+ − VTX-D- |
Measured as note 2
VTX-DIFFp-p_S
520

mV
VTX-DIFFp-p = 2 × | VTX-D+ − VTX-D- |
Measured as note 2
Defined as:
VTX-CM = DC (avg) of |VTX-D+
+ VTX-D-|/2
Measured as note 2
Defined as:
VTX-CM = DC (avg) of |VTX-D+ + VTX-D-|/2
Measured as note 2. See also note 3
DC common code
output voltage for large
voltage swing
VTX-CM_L

375
mV
DC common code
output voltage for small
voltage swing
VTX-CM_S
135
280
mV
VTX-DE-3.5-Ratio
−3.0
−4.0
dB
2, 4, 5
VTX-DE-6.0-Ratio
−5.0
−7.0
dB
2, 4, 5
De-emphasized differential
output voltage ratio for
-3.5dB de-emphasis
De-emphasized differential
output voltage ratio for
-6dB de-emphasis
VTX-CM-AC =
Max |VTX-D+ + VTX-D-|/2 – Min |VTX-D+
+ VTX-D-|/2
Measured as note 2. See also note 6
VTX-CM-AC =
Max |VTX-D+ + VTX-D-|/2 – Min |VTX-D+
+ VTX-D-|/2
Measured as note 2. See also note 6
VTX-CM-AC =
Max |VTX-D+ + VTX-D-|/2 – Min |VTX-D+
+ VTX-D-|/2
Measured as note 2. See also note 6
AC peak-to-peak common
mode output voltage for large VTX-CM-ACp-p L
swing

90
mV
AC peak-to-peak common
mode output voltage for
regular swing
VTX-CM-ACp-p R

80
mV
AC peak-to-peak common
mode output voltage for small VTX-CM-ACp-p S
swing

70
mV
VTX-IDLE-SE

50
mV
7, 8
VTX-IDLE-SE-DC

20
mV
7, 8, 9
VTX-IDLE-DIFFp-p

40
mV
8
VTX-SE
−75
750
mV
2, 10
Minimum TX eye width
TTX-Eye-MIN
0.7

UI
2, 11, 12
Maximum TX deterministic
jitter
TTX-DJ-DD

0.2
UI
2, 11, 12, 13
Instantaneous pulse width
TTX-PULSE
0.85

UI
14
30
90
ps
Given by 20%-80% voltage levels.
Measured as note 2

20
ps
Maximum single-ended
voltage in EI condition,
DC + AC
Maximum single-ended
voltage in EI condition,
DC only
Maximum peak-to-peak
differential voltage in EI
condition
Single-ended voltage
(w.r.t.VSS) on D+/D-
Differential TX output rise/fall TTX-RISE,
time
TTX-FALL
Mismatch between rise and
TTX-RF-MISMATCH
fall times
Differential return loss
RLTX-DIFF
8

dB
Common mode return loss
RLTX-CM
6

dB
Preliminary Data Sheet E0869E30 (Ver. 3.0)
14
Measured over 0.1GHz to 2.4GHz.
See also note 15
Measured over 0.1GHz to 2.4GHz.
See also note 15
EBE51FD8AGFD, EBE51FD8AGFN
Parameter
Symbol
min.
max.
Unit
Comments
Transmitter termination
resistance
RTX
41
55
Ω
16
%
RTX-Match-DC =
2×|RTX-D+ − RTX-D-| / (RTX-D+
+ RTX-D-)
Bounds are applied separately to high
and low output voltage states
D+/D- TX resistance
difference
RTX-Match-DC

4
Lane-to-lane skew at TX
LTX-SKEW 1

100 + 3UI ps
17, 19
Lane-to-lane skew at TX
LTX-SKEW 2

100 + 2UI ps
18, 19
Maximum TX Drift
(resync mode)
Maximum TX Drift
(resample mode only)
TTX-DRIFT-RESYNC 
240
ps
20
TTX-DRIFTRESAMPLE

120
ps
20
Bit Error Ratio
BER

10
-12
21
Notes: 1. For details, refer to the JEDEC specification “FB-DIMM High Speed Differential PTP Link at 1.5V”.
2. Specified at the package pins into a timing and voltage compliance test load. Common-mode
measurements to be performed using a 101010 pattern.
3. The transmitter designer should not artificially elevate the common mode in order to meet this
specification.
4. This is the ratio of the VTX-DIFFp-p of the second and following bits after a transition divided by
the VTX-DIFFp-p of the first bit after a transition.
5. De-emphasis shall be disabled in the calibration state.
6. Includes all sources of AC common mode noise.
7. Single-ended voltages below that value that are simultaneously detected on D+ and D- are interpreted as
the Electrical Idle condition.
8. Specified at the package pins into a voltage compliance test load. Transmitters must meet both singleended and differential output EI specifications.
9. This specification, considered with VRX-IDLE-SE-DC, implies a maximum 15mV single-ended DC offset
between TX and RX pins during the electrical idle condition. This in turn allows a ground offset between
adjacent FB-DIMM agents of 26mV when worst case termination resistance matching is considered.
10. The maximum value is specified to be at least (VTX-DIFFp-p L / 4) + VTX-CM L + (VTX-CM-ACp-p / 2)
11. This number does not include the effects of SSC or reference clock jitter.
12. These timing specifications apply to resync mode only.
13. Defined as the dual-dirac deterministic jitter.
14. Pulse width measured at 0 V differential.
15. One of the components that contribute to the deterioration of the return loss is the ESD structure which
needs to be carefully designed.
16. The termination small signal resistance; tolerance across voltages from 100mV to 400mV shall not
exceed ± 5Ω. with regard to the average of the values measured at 100mV and at 400mV for that pin.
17. Lane to Lane skew at the Transmitter pins for an end component.
18. Lane to Lane skew at the Transmitter pins for an intermediate component (assuming zero Lane to Lane
skew at the Receiver pins of the incoming PORT).
19. This is a static skew. An FB-DIMM component is not allowed to change its lane to lane phase relationship
after initialization.
20. Measured from the reference clock edge to the center of the output eye. This specification must be met
across specified voltage and temperature ranges for a single component. Drift rate of change is
significantly below the tracking capability of the receiver.
21. BER per differential lane.
Preliminary Data Sheet E0869E30 (Ver. 3.0)
15
EBE51FD8AGFD, EBE51FD8AGFN
Differential Receiver Input Specifications*1
Parameter
Symbol
min.
max.
Unit
Comments
VRX-DIFFp-p
170
1300
mV
VRX-DIFFp-p = 2×|VRX-D+ -VRX-D-|
Measured as note 2
VRX-IDLE-SE

65
mV
3, 4, 5, 6
VRX-IDLE-SE-DC

35
mV
3, 4, 5, 6, 7
VRX-IDLE-DIFFp-p

65
mV
4, 5, 6
VRX-SE
−300
900
mV
5
VRX-DIFF-PULSE
85

mV
5, 8
VRX-DIFF-ADJ
RATIO- HI

3.0
5, 9
VRX-DIFF-ADJ
RATIO

4.0
5, 9
Maximum RX inherent timing error TRX-TJ-MAX

0.4
UI
5, 10, 11
Maximum RX inherent
deterministic timing error
Single-pulse width at zero-voltage
crossing
Single-pulse width at minimumlevel crossing
TRX-DJ-DD

0.3
UI
5, 10, 11, 12
TRX-PW-ZC
0.55

UI
5, 8
TRX-PW-ML
0.2

UI
5, 8
TRX-RISE,
TRX-FALL
50

ps
Given by 20%-80% voltage levels.
Differential peak-to-peak input
voltage
Maximum single-ended voltage
for EI condition (AC + DC)
Maximum single-ended voltage
for EI condition (DC only)
Maximum peak-to-peak differential
voltage for EI condition
Single-ended voltage (w.r.t. VSS)
on D+/DSingle-pulse peak differential input
voltage
Amplitude ratio between adjacent
symbols,
1100mV < VRX-DIFFp-p <= 1300mV
Amplitude ratio between adjacent
symbols,
VRX-DIFFp-p <= 1100mV
Differential RX input rise/fall time
Defined as:
VRX-CM = DC (avg) of |VRX-D+
+ VRX-D-|/2
Measured as note 2.
See also note 13
VRX-CM-AC =
Max |VRX-D+ + VRX-D-|/2 –
Min |VRX-D+ + VRX-D-|/2
Measured as note 2
Common mode of the input voltage VRX-CM
120
400
mV
AC peak-to-peak common mode of
VRX-CM-ACp-p
input voltage

270
mV
Ratio of VRX-CM-ACp-p to
minimum VRX-DIFFp-p
VRX-CM-EH-Ratio

45
%
Differential return loss
RLRX-DIFF
9

dB
Common mode return loss
RLRX-CM
6

dB
RX termination resistance
RRX
41
55
Ω
D+/D- RX resistance difference
RRX-Match-DC

4
%
Lane-to-lane PCB skew at Rx
LRX-PCB-SKEW

6
UI
Minimum RX Drift Tolerance
TRX-DRIFT
400

ps
18
Minimum data tracking 3dB
bandwidth
FTRK
0.2

MHz
19
Electrical idle entry detect time
TEI-ENTRY DETECT

60
ns
20
Electrical idle exit detect time
TEI-EXIT -DETECT

30
BER

Bit Error Ratio
10
Preliminary Data Sheet E0869E30 (Ver. 3.0)
16
14
Measured over 0.1GHz to 2.4GHz.
See also note 15
Measured over 0.1GHz to 2.4GHz.
See also note 15
16
RRX-Match-DC =
2×|RRX-D+ − RRX-D-| / (RRX-D+
+ RRX-D-)
Lane-to-lane PCB skew at the
receiver that must be tolerated.
See also note 17
ns
-12
21
EBE51FD8AGFD, EBE51FD8AGFN
Notes: 1. For details, refer to the JEDEC specification “FB-DIMM High Speed Differential PTP Link at 1.5V”.
2. Specified at the package pins into a timing and voltage compliant test setup. Note that signal levels at the
pad will be lower than at the pin.
3. Single-ended voltages below that value that are simultaneously detected on D+ and D- are interpreted as
the Electrical Idle condition. Worst-case margins are determined by comparing EI levels with common
mode levels during normal operation for the case with transmitter using small voltage swing.
4. Multiple lanes need to detect the EI condition before the device can act upon the EI detection.
5. Specified at the package pins into a timing and voltage compliance test setup.
6. Receiver designers may implement either single-ended or differential EI detection. Receivers must meet
the specification that corresponds to the implemented detection circuit.
7. This specification, considered with VTX-IDLE-SE-DC, implies a maximum 15mV single-ended DC offset
between TX and RX pins during the electrical idle condition. This in turn allows a ground offset between
adjacent FB-DIMM agents of 26mV when worst case termination resistance matching is considered.
8. The single-pulse mask provides sufficient symbol energy for reliable RX reception. Each symbol must
comply with both the single-pulse mask and the cumulative eye mask.
9. The relative amplitude ratio limit between adjacent symbols prevents excessive inter-symbol interference
in the Rx. Each symbol must comply with the peak amplitude ratio with regard to both the preceding and
subsequent symbols.
10. This number does not include the effects of SSC or reference clock jitter.
11. This number includes setup and hold of the RX sampling flop.
12. Defined as the dual-dirac deterministic timing error.
13. Allows for 15mV DC offset between transmit and receive devices.
14. The received differential signal must satisfy both this ratio as well as the absolute maximum AC peak-topeak common mode specification. For example, if VRX-DIFFp-p is 200mV, the maximum AC peak-topeak common mode is the lesser of (200mV × 0.45 = 90mV) and VRX-CM-ACp-p.
15. One of the components that contribute to the deterioration of the return loss is the ESD structure which
needs to be carefully designed.
16. The termination small signal resistance; tolerance across voltages from 100mV to 400mV shall not
exceed ± 5Ω. with regard to the average of the values measured at 100mV and at 400mV for that pin.
17. This number represents the lane-to-lane skew between TX and RX pins and does not include the
transmitter output skew from the component driving the signal to the receiver. This is one component of
the end-to-end channel skew in the AMB specification.
18. Measured from the reference clock edge to the center of the input eye. This specification must be met
across specified voltage and temperature ranges for a single component. Drift rate of change is
significantly below the tracking capability of the receiver.
19. This bandwidth number assumes the specified minimum data transition density. Maximum jitter at 0.2MHz
is 0.05UI.
20. The specified time includes the time required to forward the EI entry condition.
21. BER per differential lane.
Preliminary Data Sheet E0869E30 (Ver. 3.0)
17
EBE51FD8AGFD, EBE51FD8AGFN
Serial PD Matrix for FB-DIMM
Byte No.
Function described
Byte value
Hex value
0
Number of serial PD bytes written / SPD device size / CRC coverage
116
92H
1
SPD revision
Revision 1.1
11H
2
Key byte / DRAM device type
DDR2 SDRAM FB-DIMM
09H
3
Voltage levels of this assembly
VDD = 1.8V, VCC = 1.5V
12H
4
SDRAM addressing
14-row, 10-column
44H
5
Module physical attributes
8.2mm
24H
6
Module Type / Thickness
FB-DIMM
07H
7
Module organization
1 rank / 8bits
09H
8
Fine timebase (FTB) dividend / divisor
9
Medium timebase dividend
1
01H
10
Medium timebase divisor
4
04H
11
SDRAM minimum cycle time (tCK (min.))
-6E
3.00ns
0CH
3.75ns
0FH
00H
-5C
12
SDRAM maximum cycle time (tCK (max.))
8ns
20H
13
SDRAM /CAS latencies supported
-6E
CL = 3, 4, 5
33H
CL = 3, 4
23H
-5C
14
SDRAM minimum /CAS latencies time (tCAS)
15ns
3CH
15
SDRAM write recovery times supported
-6E
WR = 2 to 5
42H
WR = 2 to 4
32H
-5C
16
SDRAM write recovery time (tWR)
15ns
3CH
17
SDRAM write latencies supported
WL = 2 to 5
42H
18
SDRAM additive latencies supported
AL = 0 to 3
40H
19
SDRAM minimum /RAS to /CAS delay (tRCD)
15ns
3CH
20
SDRAM minimum row active to row active delay (tRRD)
7.5ns
1EH
21
SDRAM minimum row precharge time (tRP)
15ns
3CH
22
SDRAM upper nibbles for tRAS and tRC
00H
23
SDRAM minimum active to precharge time (tRAS)
45ns
B4H
24
SDRAM minimum auto-refresh to active /auto-refresh time (tRC)
60ns
F0H
25
SDRAM minimum refresh recovery time delay (tRFC), LSB
105ns
A4H
26
SDRAM minimum refresh recovery time delay (tRFC), MSB
105ns
01H
27
SDRAM Internal write to read command delay (tWTR)
7.5ns
1EH
28
SDRAM Internal read to precharge command delay (tRTP)
7.5ns
1EH
29
SDRAM burst lengths supported
BL = 4, 8
03H
30
SDRAM terminations supported
ODT = 50, 75, 150Ω
07H
31
SDRAM drivers supported
Supported
01H
32
SDRAM average refresh interval (tREFI) / double refresh mode bit /
high temperature self-refresh rate support indication
7.8µs Double/HT refresh
C2H
33
Tcasemax (TC (max.)) delta / DT4R4W delta
95°C/ 0.75°C
52H
34
Psi T-A SDRAM at still air
*
Preliminary Data Sheet E0869E30 (Ver. 3.0)
18
3
××
EBE51FD8AGFD, EBE51FD8AGFN
Byte No.
Function described
Byte value
Hex value
SDRAM DT0
*
3
36
SDRAM DT2Q
*
3
××
37
SDRAM DT2P
*
3
××
SDRAM DT3N
*
3
××
39
SDRAM DT4R / mode bit
*
3
××
40
SDRAM DT5B
*
3
××
*
3
××
35
38
41
SDRAM DT7
42 to 78
Reserved
79
FB-DIMM ODT values
80
Reserved
××
00H
75Ω
01H
00H
81 to 93
AMB personality bytes
××
94 to 97
Reserved
00H
98
AMB junction temperature maximum (TJ (max.))
××
99
Category byte
100
Reserved
Planar/FDHS
0AH
00H
××
101 to 116 AMB personality bytes
117
Module ID: manufacturer’s JEDEC ID code
Elpida Memory
02H
118
Module ID: manufacturer’s JEDEC ID code
Elpida Memory
FEH
119
Module ID: manufacturing location
120
Module ID: manufacturing date
Year code (BCD)
××
121
Module ID: manufacturing date
Date code (BCD)
××
××
××
122 to 125 Module ID: module serial number
××
126 to 127 Cyclical redundancy code
128 to 145 Module part number
EBE51FD8AGFD/N
××
146
Module revision code
Initial
30H
147
Module revision code
(Space)
20H
148
SDRAM manufacturer’s JEDEC ID code
Elpida Memory
02H
149
SDRAM manufacturer’s JEDEC ID code
Elpida Memory
FEH
150
Informal AMB content revision tag (MSB)
××
151
Informal AMB content revision tag (LSB)
××
152 to 175 Manufacturer's specific data
00H
176 to 255 Open for customer use
00H
Remark IDD: DRAM current, ICC: AMB current
Notes: 1. Based on DDR2 SDRAM component specification.
2. Refer to JESD51-3 “Low effective thermal conductivity Test board for leaded surface mount packages”
under JESD51-2 standard.
3. DT parameter is derived as following: DTx = IDDx × VDD × Psi T-A, where IDDx definition is based on
JEDEC DDR2 SDRAM component specification and at VDD=1.9V, it is the datasheet (worst case) value,
and Psi T-A is the programmed value of Psi T-A (value in SPD Byte 33).
Preliminary Data Sheet E0869E30 (Ver. 3.0)
19
EBE51FD8AGFD, EBE51FD8AGFN
Physical Outline
Unit: mm
8.20 max.
Front side
Full DIMM heat spreader
74.675
5.20 max.
(DATUM -A-)
3.00 max.
D2
D4
4.00 min.
AMB
D0
3.90
D6
1
120
1.25
R0.75
1.27 ± 0.10
A
B
67.00
51.00
5.175
133.35
Back side
D1
D3
D5
D7
3.00
D8
30.35
240
17.30
121
9.50
120
FULL R
2.50
Detail B
(DATUM -A-)
1.00
0.20 ± 0.15
2.50 ± 0.20
Detail A
2.50
3.80
0.40 min.
0.80 ± 0.05
FULL R
5.00
1.50 ± 0.10
Tie bar keep out zone
ECA-TS2-0170-01
Preliminary Data Sheet E0869E30 (Ver. 3.0)
20
EBE51FD8AGFD, EBE51FD8AGFN
CAUTION FOR HANDLING MEMORY MODULES
When handling or inserting memory modules, be sure not to touch any components on the modules, such as
the memory ICs, chip capacitors and chip resistors. It is necessary to avoid undue mechanical stress on
these components to prevent damaging them.
In particular, do not push module cover or drop the modules in order to protect from mechanical defects,
which would be electrical defects.
When re-packing memory modules, be sure the modules are not touching each other.
Modules in contact with other modules may cause excessive mechanical stress, which may damage the
modules.
MDE0202
NOTES FOR CMOS DEVICES
1
PRECAUTION AGAINST ESD FOR MOS DEVICES
Exposing the MOS devices to a strong electric field can cause destruction of the gate
oxide and ultimately degrade the MOS devices operation. Steps must be taken to stop
generation of static electricity as much as possible, and quickly dissipate it, when once
it has occurred. Environmental control must be adequate. When it is dry, humidifier
should be used. It is recommended to avoid using insulators that easily build static
electricity. MOS devices must be stored and transported in an anti-static container,
static shielding bag or conductive material. All test and measurement tools including
work bench and floor should be grounded. The operator should be grounded using
wrist strap. MOS devices must not be touched with bare hands. Similar precautions
need to be taken for PW boards with semiconductor MOS devices on it.
2
HANDLING OF UNUSED INPUT PINS FOR CMOS DEVICES
No connection for CMOS devices input pins can be a cause of malfunction. If no
connection is provided to the input pins, it is possible that an internal input level may be
generated due to noise, etc., hence causing malfunction. CMOS devices behave
differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed
high or low by using a pull-up or pull-down circuitry. Each unused pin should be connected
to VDD or GND with a resistor, if it is considered to have a possibility of being an output
pin. The unused pins must be handled in accordance with the related specifications.
3
STATUS BEFORE INITIALIZATION OF MOS DEVICES
Power-on does not necessarily define initial status of MOS devices. Production process
of MOS does not define the initial operation status of the device. Immediately after the
power source is turned ON, the MOS devices with reset function have not yet been
initialized. Hence, power-on does not guarantee output pin levels, I/O settings or
contents of registers. MOS devices are not initialized until the reset signal is received.
Reset operation must be executed immediately after power-on for MOS devices having
reset function.
CME0107
Preliminary Data Sheet E0869E30 (Ver. 3.0)
21
EBE51FD8AGFD, EBE51FD8AGFN
The information in this document is subject to change without notice. Before using this document, confirm that this is the latest version.
No part of this document may be copied or reproduced in any form or by any means without the prior
written consent of Elpida Memory, Inc.
Elpida Memory, Inc. does not assume any liability for infringement of any intellectual property rights
(including but not limited to patents, copyrights, and circuit layout licenses) of Elpida Memory, Inc. or
third parties by or arising from the use of the products or information listed in this document. No license,
express, implied or otherwise, is granted under any patents, copyrights or other intellectual property
rights of Elpida Memory, Inc. or others.
Descriptions of circuits, software and other related information in this document are provided for
illustrative purposes in semiconductor product operation and application examples. The incorporation of
these circuits, software and information in the design of the customer's equipment shall be done under
the full responsibility of the customer. Elpida Memory, Inc. assumes no responsibility for any losses
incurred by customers or third parties arising from the use of these circuits, software and information.
[Product applications]
Elpida Memory, Inc. makes every attempt to ensure that its products are of high quality and reliability.
However, users are instructed to contact Elpida Memory's sales office before using the product in
aerospace, aeronautics, nuclear power, combustion control, transportation, traffic, safety equipment,
medical equipment for life support, or other such application in which especially high quality and
reliability is demanded or where its failure or malfunction may directly threaten human life or cause risk
of bodily injury.
[Product usage]
Design your application so that the product is used within the ranges and conditions guaranteed by
Elpida Memory, Inc., including the maximum ratings, operating supply voltage range, heat radiation
characteristics, installation conditions and other related characteristics. Elpida Memory, Inc. bears no
responsibility for failure or damage when the product is used beyond the guaranteed ranges and
conditions. Even within the guaranteed ranges and conditions, consider normally foreseeable failure
rates or failure modes in semiconductor devices and employ systemic measures such as fail-safes, so
that the equipment incorporating Elpida Memory, Inc. products does not cause bodily injury, fire or other
consequential damage due to the operation of the Elpida Memory, Inc. product.
[Usage environment]
This product is not designed to be resistant to electromagnetic waves or radiation. This product must be
used in a non-condensing environment.
If you export the products or technology described in this document that are controlled by the Foreign
Exchange and Foreign Trade Law of Japan, you must follow the necessary procedures in accordance
with the relevant laws and regulations of Japan. Also, if you export products/technology controlled by
U.S. export control regulations, or another country's export control laws or regulations, you must follow
the necessary procedures in accordance with such laws or regulations.
If these products/technology are sold, leased, or transferred to a third party, or a third party is granted
license to use these products, that third party must be made aware that they are responsible for
compliance with the relevant laws and regulations.
M01E0107
Preliminary Data Sheet E0869E30 (Ver. 3.0)
22