FAN5361 6MHz, 600mA / 750mA Synchronous Buck Regulator Features Description 6MHz Fixed-Frequency Operation The FAN5361 is a 600mA or 750mA, step-down, switching voltage regulator that delivers a fixed output from a 2.3V to 5.5V input voltage supply. Using a proprietary architecture with synchronous rectification, the FAN5361 is capable of delivering a peak efficiency of 92%, while maintaining efficiency over 80% at load currents as low as 1mA. 35µA Typical Quiescent Current Best-in-Class Load Transient Response Best-in-Class Efficiency 600mA or 750mA Output Current Capability 2.3V to 5.5V Input Voltage Range 1.0 to 1.90V Fixed Output Voltage Low Ripple Light-Load PFM Mode Forced PWM and External Clock Synchronization Internal Soft-Start Input Under-Voltage Lockout (UVLO) Thermal Shutdown and Overload Protection 6-bump WLCSP, 0.4mm Pitch 6-pin 2 x 2mm UMLP Applications Cell Phones, Smart Phones ® Tablets, Netbooks , Ultra-Mobile PCs ® ® 3G, LTE, WiMAX™, WiBro , and WiFi Data Cards Gaming Devices, Digital CamerasDC/DC Micro Modules The regulator operates at a nominal fixed frequency of 6MHz, which reduces the value of the external components to 470nH for the output inductor and 4.7µF for the output capacitor. The PWM modulator can be synchronized to an external frequency source. At moderate and light loads, pulse frequency modulation is used to operate the device in power-save mode with a typical quiescent current of 35µA. Even with such a low quiescent current, the part exhibits excellent transient response during large load swings. At higher loads, the system automatically switches to fixed-frequency control, operating at 6MHz. In shutdown mode, the supply current drops below 1µA, reducing power consumption. For applications that require minimum ripple or fixed frequency, PFM mode can be disabled using the MODE pin. The FAN5361 is available in 6-bump, 0.4mm pitch, WaferLevel Chip-Scale Package (WLCSP) and a 6-lead 2 x 2mm ultra-thin MLP package (UMLP). Typical Applications Figure 1. Typical Applications All trademarks are the property of their respective owners. © 2008 Fairchild Semiconductor Corporation FAN5361 • Rev. 1.1.0 www.fairchildsemi.com FAN5361 — 6MHz, 600mA / 750mA Synchronous Buck Regulator December 2010 Output (1) Voltage Part Number FAN5361UC123X 1.233V FAN5361UC182X 1.820V FAN5361UMP123X 1.233V FAN5361UMP15X 1.500V FAN5361UMP182X 1.820V Package Temperature Range Packing –40 to +85°C Tape and Reel WLCSP-6, 0.4mm Pitch 6-Lead, 2 x 2mm UMLP Note: 1. Other voltage options available on request. Contact a Fairchild representative. Pin Configurations MODE A1 A2 VIN SW B1 B2 EN FB C1 C2 GND Figure 2. WLCSP, Bumps Facing Down Figure 3. WLCSP, Bumps Facing Up Figure 4. UMLP, Leads Facing Down Pin Definitions Pin # WLCSP UMLP Name Description MODE. Logic 1 on this pin forces the IC to stay in PWM mode. A logic 0 allows the IC to MODE automatically switch to PFM during light loads. The regulator also synchronizes its switching frequency to four times the frequency provided on this pin. Do not leave this pin floating. A1 3 B1 2 SW Switching Node. Connect to output inductor. C1 1 FB Feedback / VOUT. Connect to output voltage. C2 6 GND B2 5 EN Enable. The device is in shutdown mode when voltage to this pin is <0.4V and enabled when >1.2V. Do not leave this pin floating. A2 4 VIN Input Voltage. Connect to input power source. Ground. Power and IC ground. All signals are referenced to this pin. © 2008 Fairchild Semiconductor Corporation FAN5361 • Rev. 1.1.0 www.fairchildsemi.com 2 FAN5361 — 6MHz, 600mA / 750mA Synchronous Buck Regulator Ordering Information Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol VIN VSW VCTRL Parameter Input Voltage Voltage on SW Pin Min. Max. –0.3 7.0 –0.3 Unit V (2) V (2) V (2) V VIN + 0.3 EN and MODE Pin Voltage –0.3 VIN + 0.3 Other Pins –0.3 VIN + 0.3 Human Body Model per JESD22-A114 4.0 Charged Device Model per JESD22-C101 1.5 ESD Electrostatic Discharge Protection Level TJ Junction Temperature –40 +150 °C TSTG Storage Temperature –65 +150 °C +260 °C TL Lead Soldering Temperature, 10 Seconds kV Note: 2. Lesser of 7V or VIN+0.3V. Recommended Operating Conditions The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend exceeding them or designing to Absolute Maximum Ratings. Symbol Parameter VCC Supply Voltage Range IOUT Output Current L CIN COUT Min. Typ. Max. Unit 2.3 5.5 V 0 600 mA Inductor 0.47 µH Input Capacitor 2.2 µF Output Capacitor 1.6 4.7 12.0 µF TA Operating Ambient Temperature –40 +85 °C TJ Operating Junction Temperature –40 +125 °C Thermal Properties Junction-to-ambient thermal resistance is a function of application and board layout. This data is measured with four-layer 1s2p boards in accordance to JEDEC standard JESD51. Special attention must be paid not to exceed junction temperature TJ(max) at a given ambient temperate TA. Symbol θJA Parameter Junction-to-Ambient Thermal Resistance © 2008 Fairchild Semiconductor Corporation FAN5361 • Rev. 1.1.0 Typical Unit WLCSP 150 °C/W UMLP 49 °C/W www.fairchildsemi.com 3 FAN5361 — 6MHz, 600mA / 750mA Synchronous Buck Regulator Absolute Maximum Ratings Minimum and maximum values are at VIN = VEN = 2.3V to 5.5V, VMODE = 0V (AUTO Mode), TA = -40°C to +85°C; circuit of Figure 1, unless otherwise noted. Typical values are at TA = 25°C, VIN = VEN = 3.6V. Symbol Parameter Conditions Min. Typ. Max. No Load, Not Switching 35 55 PWM Mode 6 Unit Power Supplies IQ I(SD) Quiescent Current µA mA Shutdown Supply Current VIN = 3.6V, EN = GND 0.05 1.00 VUVLO Under-Voltage Lockout Threshold Rising VIN 2.15 2.25 VUVHYST Under-Voltage Lockout Hysteresis 150 µA V mV Logic Inputs: EN and MODE Pins VIH VIL Enable HIGH-Level Input Voltage 1.2 V Enable LOW-Level Input Voltage VLHYST Logic Input Hysteresis Voltage IIN Enable Input Leakage Current 0.4 100 Pin to VIN or GND V mV 0.01 1.00 µA Switching and Synchronization fSW fSYNC (3) Switching Frequency (3) MODE Synchronization Range VIN = 3.6V, TA = 25°C 5.4 6.0 6.6 MHz Square Wave at MODE Input 1.3 1.5 1.7 MHz ILOAD = 0 to 750mA 1.862 1.900 1.957 PWM Mode 1.862 1.900 1.938 ILOAD = 0 to 600mA 1.784 1.820 1.875 Regulation 1.900V VO Output Voltage Accuracy 1.820V 1.500V 1.233V PWM Mode 1.784 1.820 1.856 ILOAD = 0 to 600mA 1.470 1.500 1.545 PWM Mode 1.470 1.500 1.530 ILOAD = 0 to 600mA 1.207 1.233 1.272 PWM Mode 1.207 V 1.233 1.259 From EN Rising Edge 180 300 PMOS On Resistance VIN = VGS = 3.6V 350 NMOS On Resistance VIN = VGS = 3.6V 225 PMOS Open-Loop Peak Current Limit VOUT = 1.233V, 1.5V, 1.82V VOUT = 1.9V 1375 TTSD Thermal Shutdown CCM Only 150 °C THYS Thermal Shutdown Hysteresis 15 °C tSS Soft-Start µs Output Driver RDS(on) ILIM(OL) 900 1100 mΩ 1250 mA Notes: 3. Limited by the effect of tOFF minimum (see Figure 14 and Figure 15 in Typical Performance Characteristics). 4. The Electrical Characteristics table reflects open-loop data. Refer to Operation Description and Typical Characteristics for closed-loop data. © 2008 Fairchild Semiconductor Corporation FAN5361 • Rev. 1.1.0 www.fairchildsemi.com 4 FAN5361 — 6MHz, 600mA / 750mA Synchronous Buck Regulator Electrical Characteristics Unless otherwise noted, VIN = VEN = 3.6V, VMODE = 0V (AUTO Mode), VOUT = 1.82V, TA = 25°C. 100% 100% 95% 95% 90% 90% 85% 80% Efficiency Efficiency 85% Auto 2.3VIN 75% 70% Auto 2.7VIN 65% Auto 3.6VIN 60% 80% 75% 25C 70% 85C 65% 60% Auto 4.2VIN 55% -30C 55% 50% 50% 1 10 100 1000 1 10 I LOAD Output Current (mA) 100 1000 I LOAD Output Current (mA) Figure 5. Efficiency vs. Load Current and Input Supply Figure 6. Efficiency vs. Load Current and Temperature 100% 95% 95% 90% 90% 85% 85% 80% 80% Efficiency Efficiency 100% 75% VIN=2.3V 70% 75% 70% VIN=2.7V 65% 65% VIN=3.6V 60% 55% 55% 50% 50% 1 10 100 Auto PFM/PWM 60% VIN=4.2V 1000 Forced PWM 1 10 I LOAD Output Current (mA) 100 1000 I LOAD Output Current (mA) Figure 7. 1.233VOUT Efficiency vs. Load Current and Supply Figure 8. Efficiency, Auto PWM/PFM vs. Forced PWM 1.248 1.84 VIN=2.3V 1.243 VIN=2.7V 1.83 VOUT (V) VOUT (V) VIN=3.6V 1.82 VIN=2.3V 1.238 VIN=4.2V 1.233 VIN=2.7V 1.81 1.228 VIN=3.6V VIN=4.2V 1.223 1.80 0 100 200 300 400 500 0.0 600 Figure 9. Load Regulation © 2008 Fairchild Semiconductor Corporation FAN5361 • Rev. 1.1.0 0.1 0.2 0.3 0.4 0.5 0.6 I LOAD Output Current (A) Load Current (mA) Figure 10. 1.233VOUT Load Regulation vs. Input Supply www.fairchildsemi.com 5 FAN5361 — 6MHz, 600mA / 750mA Synchronous Buck Regulator Typical Performance Characteristics Unless otherwise noted, VIN = VEN = 3.6V, VMODE = 0V (AUTO Mode), VOUT = 1.82V, TA = 25°C. 1.830 45 40 3.6VIN 1.825 5.5VIN 2.5VIN 30 1.820 Vout (mVpp) VOUT (V) 35 1.815 25 20 15 10 1.810 Auto PWM/PFM Forced PWM 5 0 1.805 1 10 100 1,000 0 100 200 I LOAD Output Current (mA) Figure 11. Load Regulation, Auto PFM / PWM and Forced PWM 7 Switching Frequency (MHz) 3.6VIN 5.5VIN 2.5VIN 20 Vout (mVpp) 400 500 600 Figure 12. 1.82VOUT Peak-to-Peak Output Voltage Ripple 30 25 300 Load Current (mA) 15 10 5 FPWM Mode 6 5 4 3 VIN>2.9V VIN=2.7V 2 VIN=2.5V VIN=2.3V 0 1 0 100 200 300 400 500 600 0 0.1 0.2 0.3 Load Current (mA) Figure 13. 1.233VOUT Peak-to-Peak Output Voltage Ripple 0.5 0.6 Figure 14. Effect of tOFF(MIN) on Reducing Switching Frequency 7 350 FPWM Mode 6 300 5 250 Load Current (mA) Switching Frequency (MHz) 0.4 Load Current (A) 4 3 VIN>2.4V 2 Always PWM 200 The switching mode changes at these borders 150 100 Always PFM 50 1 PFM border VIN=2.3V PWM border 0 0 0 0.1 0.2 0.3 0.4 0.5 2.5 0.6 3.5 4.0 4.5 5.0 5.5 Input Voltage (V) Load Current (A) Figure 15. 1.233VOUT Effect of tOFF(MIN) on Reducing Switching Frequency © 2008 Fairchild Semiconductor Corporation FAN5361 • Rev. 1.1.0 3.0 Figure 16. PFM / PWM Boundaries www.fairchildsemi.com 6 FAN5361 — 6MHz, 600mA / 750mA Synchronous Buck Regulator Typical Performance Characteristics (Continued) Unless otherwise noted, VIN = VEN = 3.6V, VMODE = 0V (AUTO Mode), VOUT = 1.82V, TA = 25°C. 250 42 Always PWM 40 Quiescent Current (μA) Load Current (mA) 200 The switching mode changes at these borders 150 100 Always PFM 50 PFM border 38 36 34 32 PWM border VEN=VIN 0 VEN=1.8V 2.5 3.0 3.5 4.0 4.5 5.0 5.5 30 2.0 2.5 3.0 3.5 Input Voltage (V) 4.0 4.5 5.0 5.5 VIN Input Voltage (V) Figure 17. 1.233VOUT PFM / PWM Boundaries Figure 18. Quiescent Current vs. Input Voltage 0.20 0.18 VIN=5.5V VEN=0V Supply Current (µA) 0.16 0.14 0.12 0.10 0.08 0.06 0.04 0.02 0.00 -40 -20 0 20 40 60 80 Ambient Temperature (°C) Figure 19. Shutdown Current vs. Temperature © 2008 Fairchild Semiconductor Corporation FAN5361 • Rev. 1.1.0 www.fairchildsemi.com 7 FAN5361 — 6MHz, 600mA / 750mA Synchronous Buck Regulator Typical Performance Characteristics (Continued) Unless otherwise noted, VIN = VEN = 3.6V, VMODE = 0V (AUTO Mode), VOUT = 1.82V, TA = 25°C, 5µs/div. horizontal sweep. Figure 20. Line Transient 3.3VIN to 3.9VIN, 50mA Load, 10µs/div. Figure 21. Line Transient 3.3VIN to 3.9VIN, 250mA Load, 10µs/div. Figure 22. Combined Line/Load Transient 3.9 to Figure 23. Combined Line/Load Transient 3.3 to 3.9VIN 3.3VIN Combined with 40mA to 400mA Load Transient Combined with 400mA to 40mA Load Transient Figure 24. Load Transient 0 to 150mA, 2.5VIN © 2008 Fairchild Semiconductor Corporation FAN5361 • Rev. 1.1.0 Figure 25. Load Transient 50 to 250mA, 2.5VIN www.fairchildsemi.com 8 FAN5361 — 6MHz, 600mA / 750mA Synchronous Buck Regulator Typical Performance Characteristics (Continued) Unless otherwise noted, VIN = VEN = 3.6V, VMODE = 0V (AUTO Mode), VOUT = 1.82V, TA = 25°C, 5µs/div. horizontal sweep. Figure 26. Load Transient 150 to 400mA, 2.5VIN Figure 27. Load Transient 0 to 150mA, 3.6VIN Figure 28. Load Transient 50 to 250mA, 3.6VIN Figure 29. Load Transient 150 to 400mA, 3.6VIN Figure 30. Load Transient 0 to 150mA, 4.5VIN Figure 31. Load Transient 50 to 250mA, 4.5VIN Figure 32. Load Transient 150 to 400mA, 4.5VIN © 2008 Fairchild Semiconductor Corporation FAN5361 • Rev. 1.1.0 www.fairchildsemi.com 9 FAN5361 — 6MHz, 600mA / 750mA Synchronous Buck Regulator Typical Performance Characteristics (Continued) Unless otherwise noted, VIN = VEN = 3.6V, VMODE = 0V (AUTO Mode), VOUT = 1.82V, TA = 25°C, 5µs/div. horizontal sweep. Figure 33. Metallic Short Applied at VOUT, 50μs/div. Figure 34. Metallic Short Applied at VOUT Figure 35. Over-Current Fault Response, RLOAD = 1Ω, 50μs/div. Figure 36. Over-Current Fault Response, RLOAD = 1Ω Figure 37. Overload Recovery to Light Load, 50μs/div. Figure 38. Soft-Start, RLOAD = 50Ω, 20μs/div. © 2008 Fairchild Semiconductor Corporation FAN5361 • Rev. 1.1.0 www.fairchildsemi.com 10 FAN5361 — 6MHz, 600mA / 750mA Synchronous Buck Regulator Typical Performance Characteristics (Continued) FAN5361 — 6MHz, 600mA / 750mA Synchronous Buck Regulator Typical Performance Characteristics (Continued) Unless otherwise noted, VIN = VEN = 3.6V, VMODE = 0V (AUTO Mode), VOUT = 1.82V, TA = 25°C. Figure 39. SW-Node Jitter (Infinite Persistence), ILOAD = 200mA, 50ns/div. Figure 40. Power Supply Rejection Ratio at 300mA Load © 2008 Fairchild Semiconductor Corporation FAN5361 • Rev. 1.1.0 www.fairchildsemi.com 11 To prevent shut-down during soft-start, the following condition must be met: The FAN5361 is a 600mA or 750mA, step-down, switching voltage regulator that delivers a fixed output from an input voltage supply of 2.3V to 5.5V. Using a proprietary architecture with synchronous rectification, the FAN5361 is capable of delivering a peak efficiency of 92%, while maintaining efficiency over 80% at load currents as low as 1mA. The regulator operates at a nominal frequency of 6MHz at full load, which reduces the value of the external components to 470nH for the inductor and 4.7µF for the output capacitor. IDISP + ILOAD < IMAX(DC) where IMAX(DC) is the maximum load current the IC is guaranteed to support (600mA or 750mA). Table 1 shows combinations of COUT that allow the IC to start successfully with the minimum RLOAD that can be supported. Table 1. Minimum RLOAD Values for Soft-Start with Various COUT Values Control Scheme The FAN5361 uses a proprietary, non-linear, fixed-frequency PWM modulator to deliver a fast load transient response, while maintaining a constant switching frequency over a wide range of operating conditions. The regulator performance is independent of the output capacitor ESR, allowing for the use of ceramic output capacitors. Although this type of operation normally results in a switching frequency that varies with input voltage and load current, an internal frequency loop holds the switching frequency constant over a large range of input voltages and load currents. COUT 10μF, 0805 VOUT / 0.50 Logic 1 on this pin forces the IC to stay in PWM mode. A logic 0 allows the IC to automatically switch to PFM during light loads. If the MODE pin is toggled, the converter synchronizes its switching frequency to four times the frequency on the mode pin (fMODE). The MODE pin is internally buffered with a Schmitt trigger, which allows the MODE pin to be driven with slow rise and fall times. An asymmetric duty cycle for frequency synchronization is also permitted as long as the minimum time below VIL(MAX) or above VIH(MAX) is 100ns. When EN is LOW, all circuits in FAN5361 are off and the IC draws ~50nA of current. When EN is HIGH and VIN is above its UVLO threshold, the regulator begins a soft-start cycle. The output ramp during soft-start is a fixed slew rate of 50mV/μs from 0 to 1 VOUT, then 12.5mV/μs until the output reaches its setpoint. Regardless of the state of the MODE pin, PFM mode is enabled to prevent current from being discharged from COUT if soft-start begins when COUT is charged. Current Limit, Fault Shutdown, and Restart A heavy load or short circuit on the output causes the current in the inductor to increase until a maximum current threshold is reached in the high-side switch. Upon reaching this point, the high-side switch turns off, preventing high currents from causing damage. The regulator continues to limit the current cycle-by-cycle. After 21µs of current limit, the regulator triggers an over-current fault, causing the regulator to shut down for about 85μs before attempting a restart. The IC may fail to start if heavy load is applied during startup and/or if excessive COUT is used. This is due to the currentlimit fault response, which protects the IC in the event of an over-current condition present during soft-start. The current required to charge COUT during soft-start is commonly referred to as “displacement current” is given as: If the fault was caused by short circuit, the soft-start circuit attempts to restart and produces an over-current fault after about 32μs, which results in a duty cycle of less than 30%, limiting power dissipation. (1) dV term refers to the soft-start slew rate above. dt © 2008 Fairchild Semiconductor Corporation FAN5361 • Rev. 1.1.0 VOUT / 0.60 MODE Pin Enable and Soft-Start where the 10μF, 0603 Multiple soft-start cycles are required for no-load startup if COUT is greater than 15μF. Large COUT requires light initial load to ensure the FAN5361 starts appropriately. The IC shuts down for 85μs when IDISP exceeds ILIMIT for more than 21μs of current limit. The IC then begins a new soft-start cycle. Since COUT retains its charge when the IC is off, the IC reaches regulation after multiple soft-start attempts. Combined with exceptional transient response characteristics, the very low quiescent current of the controller (35µA) maintains high efficiency; even at very light loads, while preserving fast transient response for applications requiring tight output regulation. dV dt 4.7μF, 0402 2 X 4.7μF, 0402 Minimum RLOAD VOUT / 0.60 VOUT / 0.60 Startup into Large COUT For very light loads, the FAN5361 operates in discontinuous current (DCM) single-pulse PFM mode, which produces low output ripple compared with other PFM architectures. Transition between PWM and PFM is seamless, with a glitch of less than 18mV at VOUT during the transition between DCM and CCM modes. IDISP = COUT • (2) The closed-loop peak-current limit, ILIM(PK), is not the same as the open-loop tested current limit, ILIM(OL), in the Electrical Characteristics table. This is primarily due to the effect of propagation delays of the IC current limit comparator. www.fairchildsemi.com 12 FAN5361 — 6MHz, 600mA / 750mA Synchronous Buck Regulator Operation Description When VIN is LOW, fixed switching is maintained as long as VOUT ≤ 1 − tOFF ( MIN ) • fSW ≈ 0.7 . VIN When EN is HIGH, the under-voltage lockout keeps the part from operating until the input supply voltage rises high enough to properly operate. This ensures no misbehavior of the regulator during startup or shutdown. The switching frequency drops when the regulator cannot provide sufficient duty cycle at 6MHz to maintain regulation. This occurs when VOUT is greater than or equal to 1.82V and VIN is below 2.9V at high load currents (see Figure 15). Thermal Shutdown (TSD) When the die temperature increases, due to a high load condition and/or a high ambient temperature, the output switching is disabled until the temperature on the die has fallen sufficiently. The junction temperature at which the thermal shutdown activates is nominally 150°C with a 15°C hysteresis. The calculation for switching frequency is given by: ⎛ ⎞ 1 fSW = min ⎜ , 6MHz ⎟ ⎜ t SW ( MAX ) ⎟ ⎝ ⎠ where: Minimum Off-Time Effect on Switching Frequency ⎛ VOUT + IOUT • ROFF tSW ( MAX ) = 50ns • ⎜⎜1 + ⎝ VIN − IOUT • RON − VOUT tOFF(MIN) is 50ns. This imposes constraints on the maximum VOUT that the FAN5361 can provide, or the maximum VIN output voltage it can provide at low VIN while maintaining a fixed switching frequency in PWM mode. ⎞ ⎟ ⎟ ⎠ (4) where: ROFF RON © 2008 Fairchild Semiconductor Corporation FAN5361 • Rev. 1.1.0 (3) = RDSON _ N + DCRL = RDSON _ P + DCRL www.fairchildsemi.com 13 FAN5361 — 6MHz, 600mA / 750mA Synchronous Buck Regulator Under-Voltage Lockout (UVLO) Selecting the Inductor IRMS = The output inductor must meet both the required inductance and the energy handling capability of the application. The inductor value affects average current limit, the PWM-toPFM transition point, output voltage ripple, and efficiency. VOUT ⎛ VIN − VOUT • ⎜⎜ VIN ⎝ L • fSW ⎞ ⎟ ⎟ ⎠ (5) ΔI 2 Table 2 shows the effects of inductance higher or lower than the recommended 470nH on regulator performance. Output Capacitor (6) Table 3 suggests 0402 capacitors. 0603 capacitors may further improve performance in that the effective capacitance is higher. This improves transient response and output ripple. The transition between PFM and PWM operation is determined by the point at which the inductor valley current crosses zero. The regulator DC current when the inductor current crosses zero, IDCM, is: IDCM = ΔI 2 (8) Increasing the inductor value produces lower RMS currents, but degrades transient response. For a given physical inductor size, increased inductance usually results in an inductor with lower saturation current and higher DCR. The maximum average load current, IMAX(LOAD), is related to the peak current limit, ILIM(PK) by the ripple current, given by: IMAX(LOAD ) = ILIM(PK ) − ΔI2 12 The increased RMS current produces higher losses through the RDS(ON) of the IC MOSFETs, as well as the inductor DCR. The ripple current (∆I) of the regulator is: ΔI ≈ 2 IOUT(DC) + Increasing COUT has no effect on loop stability and can therefore be increased to reduce output voltage ripple or to improve transient response. Output voltage ripple, ∆VOUT, is: ⎛ ⎞ 1 ΔVOUT = ΔI • ⎜⎜ + ESR ⎟⎟ 8 • C • f OUT SW ⎝ ⎠ (7) The FAN5361 is optimized for operation with L = 470nH, but is stable with inductances up to 1.2μH (nominal). Up to 2.2μH(nominal) may be used; however, in that case, VIN must be greater than or equal to 2.7V. The inductor should be rated to maintain at least 80% of its value at ILIM(PK). (9) Input Capacitor The 2.2μF ceramic input capacitor should be placed as close as possible between the VIN pin and GND to minimize the parasitic inductance. If a long wire is used to bring power to the IC, additional “bulk” capacitance (electrolytic or tantalum) should be placed between CIN and the power source lead to reduce ringing that can occur between the inductance of the power source leads and CIN. Efficiency is affected by the inductor DCR and inductance value. Decreasing the inductor value for a given physical size typically decreases the DCR; but since ∆I increases, the RMS current increases, as do the core and skin effect losses. The effective capacitance value decreases as VIN increases due to DC bias effects. Table 2. Effects of Changes in Inductor Value (from 470nH Recommended Value) on Regulator Performance Inductor Value IMAX(LOAD) ∆VOUT Transient Response Increase Increase Decrease Degraded Decrease Decrease Increase Improved Table 3. Recommended Passive Components and their Variation Due to DC Bias Component Description Vendor Min. L1 470nH, 2012, 90mΩ,1.1A Murata LQM21PNR47MC0 Murata LQM21PNR54MG0 Hitachi Metals HSLI-201210AG-R47 CIN 2.2μF, 6.3V, X5R, 0402 COUT 4.7μF, X5R, 0402 Typ. (5) Max. Comment 300nH 470nH 520nH Minimum value occurs at maximum current Murata or Equivalent GRM155R60J225ME15 GRM188R60J225KE19D 1.0μF 2.2μF 2.4μF Decrease primarily due to DC bias (VIN) and elevated temperature Murata or Equivalent GRM155R60G475M GRM155R60E475ME760 1.6μF 4.7μF 5.2μF Decrease primarily due to DC bias (VOUT) Note: 5. Higher inductance values are also acceptable. See “Selecting the Inductor” instructions in Applications Information. © 2008 Fairchild Semiconductor Corporation FAN5361 • Rev. 1.1.0 www.fairchildsemi.com 14 FAN5361 — 6MHz, 600mA / 750mA Synchronous Buck Regulator Applications Information There are only three external components: the inductor and the input and output capacitors. For any buck switcher IC, including the FAN5361, it is important to place a low-ESR input capacitor very close to the IC, as shown in Figure 41. The input capacitor ensures good input decoupling, which helps reduce noise appearing at the output terminals and ensures that the control sections of the IC do not behave erratically due to excessive noise. This reduces switching cycle jitter and ensures good overall performance. It is important to place the common GND of CIN and COUT as close as possible to the FAN5361 C2 terminal. There is some flexibility in moving the inductor further away from the IC; in that case, VOUT should be considered at the COUT terminal. VIN 470nH A1 A2 B1 B2 C1 C2 CIN GND COUT VOUT Figure 41. PCB Layout Guidance © 2008 Fairchild Semiconductor Corporation FAN5361 • Rev. 1.1.0 www.fairchildsemi.com 15 FAN5361 — 6MHz, 600mA / 750mA Synchronous Buck Regulator PCB Layout Guidelines FAN5361 — 6MHz, 600mA / 750mA Synchronous Buck Regulator Physical Dimensions 0.03 C F E 2X A B BALL A1 INDEX AREA 0.40 A1 D (Ø0.20) Cu Pad 0.40 F (Ø0.30) Solder Mask Opening 0.03 C 2X TOP VIEW RECOMMENDED LAND PATTERN (NSMD PAD TYPE) 0.06 C 0.378±0.018 0.208±0.021 0.625 0.547 E 0.05 C SEATING PLANE C D SIDE VIEWS Ø0.260±0.010 6X 0.40 0.005 A. NO JEDEC REGISTRATION APPLIES. C A B B. DIMENSIONS ARE IN MILLIMETERS. C B A 0.40 NOTES: C. DIMENSIONS AND TOLERANCES PER ASMEY14.5M, 1994. (Y) +/-0.018 D. DATUM C, THE SEATING PLANE IS DEFINED BY THE SPHERICAL CROWNS OF THE BALLS. F 1 2 (X) +/-0.018 E. PACKAGE TYPICAL HEIGHT IS 586 MICRONS ±39 MICRONS (547-625 MICRONS). BOTTOM VIEW F. FOR DIMENSIONS D, E, X, AND Y SEE PRODUCT DATASHEET. G. DRAWING FILENAME: UC006ACrev4. Figure 42. 6-Bump WLCSP, 0.4mm Pitch Product-Specific Dimensions Product D E X Y FAN5361UCX 1.370 +/-0.040 0.970 +/-0.040 0.285 0.285 Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. © 2008 Fairchild Semiconductor Corporation FAN5361 • Rev. 1.1.0 www.fairchildsemi.com 16 FAN5361 — 6MHz, 600mA / 750mA Synchronous Buck Regulator Physical Dimensions 0.10 C 2.0 2X A B 1.60 1.50 2.0 6 4 0.50 0.10 C 2X PIN1 IDENT 1.10 1.40 TOP VIEW 1 0.55 MAX 3 0.65 0.10 C 0.08 C 2.40 0.30 (0.15) RECOMMENDED LAND PATTERN 0.05 0.00 C SEATING PLANE SIDE VIEW NOTES: PIN1 IDENT 1 1.50 MAX A. OUTLINE BASED ON JEDEC REGISTRATION MO-229, VARIATION VCCC. 3 B. DIMENSIONS ARE IN MILLIMETERS. 6x 1.10 MAX 0.35 0.25 6 4 0.65 C. DIMENSIONS AND TOLERANCES PER ASME Y14.5M, 1994. D. DRAWING FILENAME: MKT-UMLP06Crev1 0.35 6x 0.25 1.30 0.10 C A B 0.05 C BOTTOM VIEW Figure 43. 6-Lead, 2 x 2mm, Ultra-Thin Molded Leadless Package (UMLP) Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. © 2008 Fairchild Semiconductor Corporation FAN5361 • Rev. 1.1.0 www.fairchildsemi.com 17 FAN5361 — 6MHz, 600mA / 750mA Synchronous Buck Regulator © 2008 Fairchild Semiconductor Corporation FAN5361 • Rev. 1.1.0 www.fairchildsemi.com 18