Finisar Product Specification 1000BASE-T Copper GBIC Transceivers FCM-8520/8521-3 Product Features • • • • • • Up to 1.25Gb/s bi-directional data links Extended operating temperature range (0°C to +75°C) Hot-pluggable Fully metallic enclosure for low EMI Low power (1.5W typical) Access to physical layer IC via 2wire serial bus Applications • 1.25 Gigabit Ethernet over Cat 5 cable Finisar’s FCM-8520/8521-3 1000BASE-T Copper GBIC transceivers are based on the GBIC Specification Revision 5.51. They are compatible with the Gigabit Ethernet and 1000BASE-T standards as specified in IEEE Std 802.3z2 and IEEE Std 802.3ab3. The FCM-8520-3 uses the GBIC’s RX_LOS pin for link indication, and 1000BASE-X auto-negotiation must be disabled on the host system. The FCM-8521-3 is compatible with 1000BASE-X auto-negotiation, but does not have a link indication feature (RX_LOS is internally grounded). See AN-2032, “Commonly Asked Questions Regarding Auto-negotiation on Finisar’s 1000BASE-T GBICs”4, for a more complete explanation on the differences between the two models. PRODUCT SELECTION Part Number FCM-8520-3 FCM-8521-3 Finisar Corporation Rev A, Feb 2003 Link Indicator on RX_LOS Pin Yes No Compatible with 1000BASE-X Auto-negotiation No Yes Page 1 F i n i s a r FCM-8520/8521-3 1000BASE-T GBIC Product Specification I. GBIC to Host Connector Pin Out Pin Name Pin # Sequence RX_LOS* 1 2 GND 2 2 GND 3 2 MOD_DEF(0) 4 2 MOD_DEF(1) 5 2 MOD_DEF(2) 6 2 TX_DISABLE 7 2 GND 8 2 GND 9 2 GND 10 2 GND 11 1 -RX_DAT 12 1 +RX_DAT 13 1 GND 14 1 VCC 15 2 VCC 16 2 GND 17 1 +TX_DAT 18 1 -TX_DAT 19 1 GND 20 1 Note: RX_LOS is used for link indication on the FCM8520-3, and is internally grounded on the FCM-8521-3 Table 1. GBIC to host connector pin assignment “Sequence” indicates the order in which pins make contact when the device is hot plugged. For additional information, see “Table 3: Signal Definitions” in the GBIC Specification Revision 5.5.1 Finisar Corporation Rev A, Feb 2003 Page 2 F i n i s a r FCM-8520/8521-3 1000BASE-T GBIC Product Specification II. +5V Volt Electrical Power Interface The FCM-8520/8521-3 has an extended input voltage range of 4.5 to 5.5 V, compared to the GBIC standard of 4.25 to 5.25 V. The 6V maximum voltage is not allowed for continuous operation. +5 Volt Electrical Power Interface Parameter Supply Current Symbol Is Min Typ 310 Max 375 Units mA Input Voltage Vcc 4.5 5 5.5 V Maximum Voltage Vmax 6 V Surge Current Isurge 450 mA Notes/Conditions 1.7W max power over full range of voltage and temperature. See Note 1. Referenced to GND. Hot plug. See Note 1. Table 2. +5 Volt electrical power interface Note: 1. Caution: Power consumption and inrush current are higher than the specified values in the GBIC Specification Rev 5.51. III. Low-Speed Signals RX_LOS is a TTL signals as described in Table 3 and 4. MOD_DEF(1) (SCL) and MOD_DEF(2) (SDA), are open drain CMOS signals (see section VII, “Serial Communication Protocol”). Both MOD_DEF(1) and MOD_DEF(2) must be pulled up to host_Vcc. For more detailed information, see sections 5.3.1 – 5.3.8 in the GBIC Specification Rev. 5.51. Low-Speed Signals, Electronic Characteristics Parameter GBIC Output LOW GBIC Output HIGH GBIC Input LOW GBIC Input HIGH Finisar Corporation Rev A, Feb 2003 Symbol VOL Min 0 Max 0.5 Units Notes/Conditions V 4.7k to 10k pull-up to host_Vcc, measured at host side of connector VOH host_Vcc - 0.5 host_Vcc + 0.3 V 4.7k to 10k pull-up to host_Vcc, measured at host side of connector VIL 0 0.8 V 4.7k to 10k pull-up to Vcc, measured at GBIC side of connector VIH 2 Vcc + 0.3 V 4.7k to 10k pull-up to Vcc, measured at GBIC side of connector Table 3. Low-speed signals, electronic characteristics Page 3 F i n i s a r FCM-8520/8521-3 1000BASE-T GBIC Product Specification High-Speed Electrical Interface, Transmission Line-GBIC Parameter Line Frequency Tx Output Impedance Rx Input Impedance Symbol fL Min Typ 125 Max Units MHz Notes/Conditions 5-level encoding, per IEEE 802.3ab. Zout,TX 100 Ohm Differential, for all frequencies between 1MHz and 125MHz. Zin,RX 100 Ohm Differential, for all frequencies between 1MHz and 125MHz. Table 4. High-speed electrical interface, transmission line-GBIC IV. High-Speed Electrical Interface All high-speed signals are AC-coupled internally. High-Speed Electrical Interface, Host-GBIC Parameter Differential Input Voltage Differential Output Voltage Rise/Fall Time Tx Input Impedance Rx Output Impedance Symbol Vindiff Min 0.50 Voutdiff 0.37 Typ Max 2.00 Units V Notes/Conditions Differential peak - peak 2.00 V Differential peak - peak Tr,Tf Zin 250 75 psec Ohm Zout 75 Ohm 20%-80% Differential Table 5. High-speed electrical interface, host-GBIC V. General Specifications General Parameter Data Rate Cable Length Symbol Min BR L Typ Max 1.25 Units Notes/Conditions Gb/sec IEEE 802.3 compatible. See Notes 1 and 2 below. 100 m Category 5 UTP. BER <10-10 Table 6. General specifications Notes: 1. Clock tolerance is ±50 ppm 2. The FCM-8520/8521-3 is a full-duplex device in the “Preferred Master” mode. 3. Automatic crossover detection is enabled. External crossover cable is not required Finisar Corporation Rev A, Feb 2003 Page 4 F i n i s a r FCM-8520/8521-3 1000BASE-T GBIC Product Specification VI. Environmental Specifications The FCM-8520-3 has an extended range from 0°C to +75°C case temperature as specified in Table 8. Environmental Specifications Parameter Operating Temperature Storage Temperature Symbol Top Tsto Min 0 -40 Typ Max 75 85 Units °C °C Notes/Conditions Case temperature Ambient temperature Table 7. Environmental specifications VII. Serial Communication Protocol All Finisar GBICs are ‘Module Definition “4”’ and support the 2-wire serial communication protocol outlined in the GBIC Specification1. These GBICs use an Atmel AT24C01A 128 byte E2PROM with an address of A0h. For details on interfacing with the E2PROM, see the Atmel data sheet titled “AT24C01A/02/04/08/16 2-Wire Serial CMOS E2PROM.”5 The 1000BASE-T physical layer IC can also be accessed via the 2-wire serial bus at address A4h. For details interfacing with the PHY IC, see Marvell data sheet titled “Alaska Ultra 88E1011/88E1001S Integrated Gigabit Ethernet Transceiver”6 (Marvell document number MV-5100281-00). Serial Bus Timing Requirements Parameter I2C Clock Rate Symbol Min 0 Typ Max 100,000 Units Notes/Conditions Hz Table 8. Serial bus timing requirements Finisar Corporation Rev A, Feb 2003 Page 5 FCM-8520/8521-3 1000BASE-T GBIC Product Specification F i n i s a r VIII. Mechanical Specifications The host-side of the FCM-8520-3 conforms to the mechanical specifications outlined in the GBIC Specification Revision 5.5, Section 61. The front portion of the GBIC (part extending beyond the face plate of the host) is larger to accommodate the RJ-45 connector. See Figure 1 below for details. Figure 1. FCM-8520/8521-3 mechanical dimensions Finisar Corporation Rev A, Feb 2003 Page 6 FCM-8520/8521-3 1000BASE-T GBIC Product Specification F i n i s a r IX. References 1. “Gigabit Interface Converter (GBIC) Revision 5.5”. Sun Microsystems Computer Company et. al., September 27, 2000. http://playground.sun.com/pub/OEmod/ 2. IEEE Std 802.3z. IEEE Standards Department, 2000. 3. “IEEE Std 802.3ab-1999 ‘Physical Layer Parameters and Specifications for 1000 Mb/s Operation Over 4-Pair of Category 5 Balanced Copper Cabling, Type 1000BASE-T”. IEEE Standards Department, 1999. 4. “Application Note AN-XXXX: Commonly Asked Questions Regarding Autonegotiation on Finisar’s 1000BASE-T GBICs”, Finisar Corporation, February 2003 5. “AT24C01A/02/04/08/16 2-Wire Serial CMOS E2PROM”. Atmel Corporation. www.Atmel.com 6. “Alaska Ultra 88E1011/88E1001S Integrated 10/100/1000 Gigabit Ethernet Transceiver”. Marvell Corporation. www.marvell.com X. For More Information Finisar Corporation 1308 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 [email protected] www.finisar.com Finisar Corporation Rev A, Feb 2003 Page 7