FRAF1601G-FRAF1607G Isolated 16.0AMP. Glass Passivated Fast Recovery Rectifiers ITO-220AC .185(4.7) .173(4.4) Features .134(3.4)DIA .113(3.0)DIA Glass passivated chip junction. High efficiency, Low VF High current capability High reliability High surge current capability Low power loss .112(2.85) .100(2.55) .272(6.9) .248(6.3) .606(15.5) .583(14.8) .063(1.6) MAX .161(4.1) .146(3.7) Mechanical Data .406(10.3) .390(9.90) .124(3.16) .118(3.00) Cases: ITO-220AC molded plastic Epoxy: UL 94V-0 rate flame retardant Polarity: As marked High temperature soldering guaranteed: 260 o C /10 seconds 0.25”,(6.35mm) from case. Mounting position: Any Weight: 2.24 grams Mounting torque: 5 in – 1bs. max. .110(2.8) .098(2.5) .055(1.4) .043(1.1) .030(0.76) .020(0.50) .035(0.9) .020(0.5) .071(1.8) MAX .543(13.8) .512(13.2) 2 .100(2.55) .100(2.55) PIN 1 PIN 2 CASE Case Positive Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics o Rating at 25 C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Type Number Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current See Fig. 1 Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 16.0A Maximum DC Reverse Current @ T C =25 o C at Rated DC Blocking Voltage @ T C =125 o C Symbol FRAF FRAF FRAF FRAF FRAF FRAF FRAF Units 1601G 1602G 1603G 1604G 1605G 1606G 1607G V RRM V RMS V DC 100 70 100 200 140 200 400 280 400 600 420 600 800 560 800 1000 700 1000 16.0 A IFSM 250 A VF 1.3 V IR 5.0 100 uA uA nS pF o C/W o C Trr Typical Junction Capacitance (Note 3) Cj R θJC 150 250 70 4.5 -65 to +150 500 Operating and Storage Temperature Range T J, T STG 1. Reverse Recovery Test Conditions: IF =0.5A, IR =1.0A, IRR =0.25A. Notes: 2. Thermal Resistance from Junction to Case Per Leg Mounted on Heatsink Size 2” x 3” x 0.25” Al-Plate. 3. Measured at 1MHz and Applied Reverse Voltage of 4.0 Volts D.C. http://www.luguang.cn V V V I(AV) Maximum Reverse Recovery Time ( Note 1) Typical Thermal Resistance RθJC (Note 2) 50 35 50 mail:[email protected] FRAF1601G-FRAF1607G Isolated 16.0AMP. Glass Passivated Fast Recovery Rectifiers RATINGS AND CHARACTERISTIC CURVES (FRAF1601G THRU FRAF1607G) 1000 16 INSTANTANEOUS REVERSE CURRENT. ( A) AVERAGE FORWARD CURRENT. (A) FIG.2- TYPICAL REVERSE CHARACTERISTICS PER LEG FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE 20 12 8 4 0 0 50 100 150 o CASE TEMPERATURE. ( C) FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 100 Tj=125 0C 10 1 Tj=25 0C PEAK FORWARD SURGE CURRENT. (A) 300 TJ=125 0C 250 0.1 8.3ms Single Half Sine Wave JEDEC Method 200 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 150 FIG.5- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG 100 80 50 40 0 2 5 10 20 50 100 NUMBER OF CYCLES AT 60Hz FIG.4- TYPICAL JUNCTION CAPACITANCE 150 125 CAPACITANCE.(pF) 20 INSTANTANEOUS FORWARD CURRENT. (A) 1 100 75 50 10 4 2 1 0.4 Tj=25oC Pulse Width=300 s 1% Duty Cycle 0 25 0 0.1 Tj=25 C f=1.0MHz Vsig=50mVp-p 0.5 1 0.2 5 10 50 100 0.1 0.8 500 1000 REVERSE VOLTAGE. (V) 0.9 1.0 1.1 1.2 1.3 FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50W NONINDUCTIVE 10W NONINDUCTIVE trr +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE 1.4 INSTANTANEOUS FORWARD VOLTAGE. (V) OSCILLOSCOPE (NOTE 1) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms http://www.luguang.cn 0 -0.25A (+) -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm mail:[email protected] 1.5