GM34063 series 1.5A DC TO DC CONVERTER CONTROL Description Features GM34063 series have all the functions required for DC-to-DC converters: an internal Temperaturecompensated reference, comparator, controlled duty cycle oscillator with an active current limit circuit, driver, and high current output switch. GM34063 series are designed for step-down, step-up and voltage-inverting applications by using a minimum number of external components. For GM34063E can operate for a temperature range from -40°C to 125°C while GM34063F can operate from -25°C to 85°C. 3.0V to 40V Input Adjustable Output Voltage Output Switch Current to 1.5A Low Standby Current Operating Frequency to 100kHz Precision 1 % Reference available Application z CD-ROM z Battery Chargers z Motherboards z DSL Modem z SMPS Power Supply Schematic Diagram S Q Q2 Q1 R 6 100 VCC IPK Oscillator 2 Switch Emitter 3 7 IPK Sense Comparator + - 5 Comparator Inverting Input Timing Capacitor 1.25V VREF 4 GND GM34063V2.00 CT 1 GM34063 series 1.5A DC TO DC CONVERTER CONTROL GM34063V2.00 Pin Configurations 2 Pin 1 Switch Collector Pin 2 Switch Emitter Pin 3 Timing Capacitor Pin 4 Gnd Pin 5 Comparator Inverting Input Pin 6 VCC Pin 7 IPK Sense Pin 8 Driver Collector GM34063 series 1.5A DC TO DC CONVERTER CONTROL Marking Information, GM34063 – Pb Free Product SO8 GM34063 AYWW DIP8 GM34063 AYWW A: Assembly / Test site code Y: Year WW: Week Marking Information, GM34063E – Green Product SO8 GM34063EG AYWW DIP8 GM34063EG AYWW E: Operating Temperature Range: -40°C to 125°C G: Green Product A: Assembly / Test site code Y: Year SO8 DIP8 GM34063FG AYWW GM34063FG AYWW F: Operating Temperature Range: -25°C to 85°C G: Green Product A: Assembly / Test site code Y: Year GM34063V2.00 Marking Information, GM34063F – Green Product 3 GM34063 series 1.5A DC TO DC CONVERTER CONTROL Ordering Information GM34063 – Pb Free Product Ordering Number Package Shipping GM34063D8T DIP-8 60 Units / Tube GM34063S8T SOP-8 100 Units / Tube GM34063S8R SOP-8 2,500 Units / Tape & Reel Package Shipping GM34063ED8TG DIP-8 60 Units / Tube GM34063ES8TG SOP-8 100 Units / Tube GM34063ES8RG SOP-8 2,500 Units / Tape & Reel Package Shipping GM34063FD8TG DIP-8 60 Units / Tube GM34063FS8TG SOP-8 100 Units / Tube GM34063FS8RG SOP-8 2,500 Units / Tape & Reel GM34063E – Green Product Ordering Number GM34063F – Green Product GM34063V2.00 Ordering Number 4 GM34063 series 1.5A DC TO DC CONVERTER CONTROL Absolute Maximum Ratings Parameter Symbol Vaule Unit Power Supply Voltage VCC 40 Vdc Comparator Input Voltage Range VIR -0.3 to +40 Vdc Switch Collector Voltage VC()switch 40 Vdc Switch Emitter Voltage (PIN1 = 40V) VE(switch) 40 Vdc Switch Collector Emitter Voltage VCE(switch) 40 Vdc VC(driver) 40 Vdc IC(driver) 100 mA ISW 1.5 A Driver Collector Voltage Driver Collect Current (Note 1) Switch Current Power dissipation DIP 8 780 SO 8 510 GM34063 Operating Temperature Range 0 to 70 GM34063E -40 to 125 GM34063F -25 to 85 Storage Temperature Lead Temperature (soldering 10 sec.) mW °C - 65 to 150 °C 260 °C GM34063V2.00 Note 1. Maximum package power dissipation limits must be observed 5 GM34063 series 1.5A DC TO DC CONVERTER CONTROL Electrical Characteristics (VCC = 5.0V , TA = 25°C unless otherwise specified) Parameter Symbol Condition Min Typ Max Unit OSCILLATOR Frequency fOSC VPIN5 = 0V, CT = 1.0nF 24 33 42 kHz Charge Current Ichg VCC = 5.0V to 40V 24 35 42 μA Idischg VCC = 5.0V to 40V 140 220 260 µA Discharge Current Discharge to Charge Current Ratio Idischg/Ichg Pin 7 to VCC 5.2 6.5 7.5 - Current Limit Sense Voltage Vipk(sense) Ichg = Idischg 250 300 350 mV Saturation Voltage 1 VCE (sat1) Darlington Connection, ISW = 1.0A, Pins 1, 8 Connected TA = Full range 1.0 1.3 V Saturation Voltage 2 (Note 3) VCE (sat2) Darlington Connection, ISW = 1.0A, RPIN 8 = 82Ω to VCC, Forced β= 20, TA = Full range 0.45 0.7 V OUTPUT SWITCH (Note 2) DC Current Gain hFE Collector Off-State Current IC(OFF) ISW = 1.0A, VCE = 5V 50 75 - 40 100 1.225 1.25 1.275 Note 4 1.238 1.25 1.263 TA = Full range 1.21 VCE = 40V, TA = Full range µA COMPARATOR Threshold Voltage Vth Threshold Voltage Line Regulation Regline Input Bias Current VCC = 5.0V to 40V, TA = Full range IIB Vin = 0V, TA = Full range ICC VCC = 5V to 40V, CT = 1.0nF, Pin 7 = VCC, Vpin 5 > Vth, Pin 2 = Gnd, remaining pins open TA = Full range - V 1.29 1.4 5.0 mV -20 -400 nA TOTAL DEVICE Supply Current 50 75 mA GM34063V2.00 Note 2. Low duty cycle pulse techniques are used during test to maintain junction temperature as close to ambient as possible. 6 Note 3. If the output switch is driven into hard saturation (non-Darlington configuration) at low switch currents ( ≤ 300 mA) and high driver currents ( ≥ 30 mA), it may take up to 2.0 ms for it to come out of saturation. This condition will shorten the off time at frequencies 30 kHz, and is magnified at high temperatures. This condition does not occur with a Darlington configuration, since the output switch cannot saturate. If a non-Darlington configuration is used, the following output drive condition is recommended: Forced β of output switch: lC output lC driver - 7.0 mA * ≥ 10 * The 100 Ω resistor in the emitter of the driver device requires about 7.0 mA before the output switch conducts. Note 4. 1% accuracy is available upon special request GM34063 series 1.5A DC TO DC CONVERTER CONTROL Typical Application Circuits R7 0 Rsc 0.1 1/2W 8 1 7 2 R9 R5 220 330 U2 CEM9435A GM34063 VIN 6 C13 100uF 16V Low ESR 3 4 5 R1 15K 1% R2 5K 1% L2 220uH R6 10 C2 470pF 50V C.C. R17 0 C4 0.1uF 50V C.C. D1 MBRS140 MBRS320 MBRS340 VOUT 5V Optional C5 1000pF 50V C.C. Optional C15 470uF 6.3V Low ESR GM34063V2.00 Figure 1 Step Down with External MOS Transistor 7 GM34063 series 1.5A DC TO DC CONVERTER CONTROL Typical Performance Characteristics 2.0 3.6 1.8 3.2 ICC Supply Current (mA) VCE Saturation Voltage (V) 1.6 1.4 1.2 1.0 0.8 0.6 VCC = 5V Pin 1, 7, 8 = VCC Pin 3, 5 = GND TA = 25°C 0.4 0.2 0 0 2.0 1.6 1.2 0.8 35 40 VCC = 5V IC = 1A 1000 950 0.9 0.8 0.7 0.6 900 0.5 0.4 0.3 0.2 0.1 0 850 VCC = 5V Pin 7 = VCC Pin 2, 3, 5 = GND TA = 25°C 0.2 800 750-40 0.4 0.6 0.8 1.0 1.2 1.4 IC Collector Current (A) 0 40 80 120 TJ (°C) Figure 4: Darlington Configuration Collector Emitter Saturation Voltage (VCE(SAT)) vs. Temperature 400 1000 VCC = 5V Ichg = Idischg 380 360 340 320 300 280 260 240 220 200 -55 -25 0 25 50 75 100 125 Ton-off Output Switch on-off Time (µV) VIPK(sense) Current Limit Sense Voltage (V) 10 15 20 25 30 VCC Supply Voltage (V) Figure 2: Standby Supply Current vs. Supply Voltage Figure 3: Common Emitter Configuration Output Switch Saturation Voltage vs. Collector Current GM34063V2.00 5 VCE (SAT) (mV) Darlington Connection 0 8 CT = 1.0nF Pin 7 = VCC Pin 2 = GND 0 0 Figure 1: Emitter Follows Configuration Output VCE(sat) Saturation Voltage (V) 2.4 0.4 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 lE Emitter current (A) 1.4 1.3 1.2 1.1 1.0 2.8 500 200 100 VCC = 5V Pin 7 = VCC Pin 5 = GND TA = 25°C 50 ton 20 10 toff 5.0 2.0 1.0 0.02 0.01 0.05 0.1 0.2 0.5 1.0 2.0 5.0 10 TA, AMBIENT TEMPERATURE (°C) CT, Oscillator Timing Capacitor (nF) Figure 5: Current Limit Sense Voltage Vs. Temperature Figure 6: Output Switch On-Off Time vs. Oscillator Timing Capacitor GM34063 series 1.5A DC TO DC CONVERTER CONTROL Package Outline Dimensions – SO 8 0.189 - 0.197 (4.800 - 5.004) 0.228 - 0.244 (5.791 - 6.198) 0.016 - 0.050 (0.406 - 0.270) D 0.014 - 0.020 (0.356 - 0.508) 0.050 (1.270) TYP 0.150 - 0.157 (3.810 - 3.988) 0.053 - 0.059 (1.346 - 1.753) SEATING PLAN 0.004 - 0.010 (0.012 - 0.254) 8.0 MAX 0.008 - 0.010 (0.203 - 0.254) Package Outline Dimensions – DIP 8 0.250 +/- 0.005 (6.350 +/- 0.127) 0.370 - 0.400 (9.474 - 10.150) 0.145 - 0.200 (3.683 - 5.080) 0.125 - 0.140 (3.175 - 3.556) 0.045 +/- 0.015 (1.143 +/- 0.183) 0.108 +/- 0.003 (0.457 +/- 0.076) 0.100 +/- 0.010 (2.540 +/- 0.254) J 0.009 - 0.010 (0.299 - 0.381) 95 +/- 5 GM34063V2.00 0.300 - 0.320 (7.620 - 8.128) 0.06 (1.524) 9 GM34063 series 1.5A DC TO DC CONVERTER CONTROL Ordering Number GM 34063E S8 APM Gamma R G Blank: Pb-free G:Green Circuit Type Package Type Shipping Type 34063 34063E 34063F S8: SO 8 D8: DIP 8 R: Taping & Reel T: Tube Note: Pb-free products: ♦ RoHS compliant and compatible with the current require-ments of IPC/JEDEC J-STD-020. ♦ Suitable for use in SnPb or Pb-free soldering processes with 100% matte tin (Sn) plating. GM34063V2.00 Green products: 10 ♦ Lead-free (RoHS compliant) ♦ Halogen free(Br or Cl does not exceed 900ppm by weight in homogeneous material and total of Br and Cl does not exceed 1500ppm by weight)