HM6264B Series 64 k SRAM (8-kword × 8-bit) ADE-203-454B (Z) Rev. 2.0 Nov. 1997 Description The Hitachi HM6264B is 64k-bit static RAM organized 8-kword × 8-bit. It realizes higher performance and low power consumption by 1.5 µm CMOS process technology. The device, packaged in 450 mil SOP (foot print pitch width), 600 mil plastic DIP, 300 mil plastic DIP, is available for high density mounting. Features • High speed Fast access time: 85/100 ns (max) • Low power Standby: 10 µW (typ) Operation: 15 mW (typ) (f = 1 MHz) • Single 5 V supply • Completely static memory No clock or timing strobe required • Equal access and cycle times • Common data input and output Three state output • Directly TTL compatible All inputs and outputs • Battery backup operation capability HM6264B Series Ordering Information Type No. Access time Package HM6264BLP-8L HM6264BLP-10L 85 ns 100 ns 600-mil, 28-pin plastic DIP (DP-28) HM6264BLSP-8L HM6264BLSP-10L 85 ns 100 ns 300-mil, 28-pin plastic DIP(DP-28N) HM6264BLFP-8LT HM6264BLFP-10LT 85 ns 100 ns 450-mil, 28-pin plastic SOP(FP-28DA) Pin Arrangement HM6264BLP/BLSP/BLFP Series NC A12 A7 A6 A5 A4 A3 1 2 A2 A1 A0 8 9 10 11 12 21 20 19 18 17 VCC WE CS2 A8 A9 A11 OE A10 CS1 I/O8 I/O7 I/O6 13 14 16 15 I/O5 I/O4 I/O1 I/O2 I/O3 VSS 28 27 26 25 24 3 4 5 6 7 23 22 (Top view) Pin Description Pin name Function Pin name Function A0 to A12 Address input WE Write enable I/O1 to I/O8 Data input/output OE Output enable CS1 Chip select 1 NC No connection CS2 Chip select 2 VCC Power supply VSS Ground HM6264B Series Block Diagram A11 A8 A9 A7 A12 A5 A6 A4 Row decoder I/O1 Column I/O Input data control I/O8 CS2 CS1 Memory array 256 × 256 Column decoder A1 A2 A0 A10 A3 Timing pulse generator Read, Write control WE OE VCC VSS HM6264B Series Function Table WE CS1 CS2 OE Mode VCC current I/O pin Ref. cycle × H × × Not selected (power down) I SB , I SB1 High-Z — × × L × Not selected (power down) I SB , I SB1 High-Z — H L H H Output disable I CC High-Z — H L H L Read I CC Dout Read cycle (1)–(3) L L H H Write I CC Din Write cycle (1) L L H L Write I CC Din Write cycle (2) Note: ×: H or L Absolute Maximum Ratings Parameter Power supply voltage *1 Symbol Value VCC –0.5 to +7.0 Unit V *1 VT –0.5 to V CC + 0.3 Power dissipation PT 1.0 W Operating temperature Topr 0 to + 70 °C Storage temperature Tstg –55 to +125 °C Storage temperature under bias Tbias –10 to +85 °C Terminal voltage *2 *3 V Notes: 1. Relative to VSS 2. VT min: –3.0 V for pulse half-width ≤ 50 ns 3. Maximum voltage is 7.0 V Recommended DC Operating Conditions (Ta = 0 to +70°C) Parameter Symbol Min Typ Max Unit Supply voltage VCC 4.5 5.0 5.5 V VSS 0 0 0 V VIH 2.2 — VCC + 0.3 V — 0.8 V Input high voltage Input low voltage Note: VIL –0.3 1. VIL min: –3.0 V for pulse half-width ≤ 50 ns *1 HM6264B Series DC Characteristics (Ta = 0 to +70°C, VCC = 5 V ±10%, VSS = 0 V) Parameter Symbol Min Typ*1 Max Unit Test conditions Input leakage current |ILI| — — 2 µA Vin = VSS to V CC Output leakage current |ILO | — — 2 µA CS1 = VIH or CS2 = VIL or OE = VIH or WE = VIL, VI/O = VSS to V CC Operating power supply current I CCDC — 7 15 mA CS1 = VIL, CS2 = VIH, I I/O = 0 mA others = VIH/VIL Average operating power supply current I CC1 — 30 45 mA Min cycle, duty = 100%, CS1 = VIL, CS2 = VIH, I I/O = 0 mA others = VIH/VIL I CC2 — 3 5 mA Cycle time = 1 µs, duty = 100%, II/O = 0 mA CS1 ≤ 0.2 V, CS2 ≥ VCC – 0.2 V, VIH ≥ VCC – 0.2 V, VIL ≤ 0.2 V I SB — 1 3 mA CS1 = VIH, CS2 = VIL I SB1 — 2 50 µA CS1 ≥ VCC – 0.2 V, CS2 ≥ VCC – 0.2 V or 0 V ≤ CS2 ≤ 0.2 V, 0 V ≤ Vin Output low voltage VOL — — 0.4 V I OL = 2.1 mA Output high voltage VOH 2.4 — — V I OH = –1.0 mA Standby power supply current Notes: 1. Typical values are at VCC = 5.0 V, Ta = +25°C and not guaranteed. Capacitance (Ta = 25°C, f = 1.0 MHz) Parameter Input capacitance *1 *1 Input/output capacitance Note: Symbol Min Typ Max Unit Test conditions Cin — — 5 pF Vin = 0 V CI/O — — 7 pF VI/O = 0 V 1. This parameter is sampled and not 100% tested. HM6264B Series AC Characteristics (Ta = 0 to +70°C, VCC = 5 V ± 10%, unless otherwise noted.) Test Conditions • • • • Input pulse levels: 0.8 V to 2.4 V Input and output timing reference level: 1.5 V Input rise and fall time: 10 ns Output load: 1 TTL Gate + CL (100 pF) (Including scope & jig) Read Cycle HM6264B-8L HM6264B-10L Parameter Symbol Min Max Min Max Unit Read cycle time t RC 85 — 100 — ns Address access time t AA — 85 — 100 ns CS1 t CO1 — 85 — 100 ns CS2 t CO2 — 85 — 100 ns t OE — 45 — 50 ns CS1 t LZ1 10 — 10 — ns 2 CS2 t LZ2 10 — 10 — ns 2 Output enable to output in low-Z t OLZ 5 — 5 — ns 2 Chip deselection in to output in high-Z CS1 t HZ1 0 30 0 35 ns 1, 2 CS2 t HZ2 0 30 0 35 ns 1, 2 Output disable to output in high-Z t OHZ 0 30 0 35 ns 1, 2 Output hold from address change t OH 10 — 10 — ns Chip select access time Output enable to output valid Chip selection to output in low-Z Notes Notes: 1. t HZ is defined as the time at which the outputs achieve the open circuit conditions and are not referred to output voltage levels. 2. At any given temperature and voltage condition, t HZ maximum is less than tLZ minimum both for a given device and from device to device. HM6264B Series Read Timing Waveform (1) (WE = VIH) tRC Address Valid address tAA tCO1 CS1 tLZ1 tCO2 CS2 tHZ1 tLZ2 tOE tHZ2 tOLZ OE tOHZ Dout High Impedance Valid data tOH Read Timing Waveform (2) (WE = VIH, OE = VIL ) Address Valid address t AA t OH Dout t OH Valid data HM6264B Series Read Timing Waveform (3) (WE = VIH, OE = VIL )*1 t CO1 CS1 t HZ1 t LZ1 t HZ2 CS2 t CO2 t LZ2 Dout Note: Valid data 1. Address must be valid prior to or simultaneously with CS1 going low or CS2 going high. HM6264B Series Write Cycle HM6264B-8L HM6264B-10L Parameter Symbol Min Max Min Max Unit Notes Write cycle time t WC 85 — 100 — ns Chip selection to end of write t CW 75 — 80 — ns 2 Address setup time t AS 0 — 0 — ns 3 Address valid to end of write t AW 75 — 80 — ns Write pulse width t WP 55 — 60 — ns 1, 6 Write recovery time t WR 0 — 0 — ns 4 WE to output in high-Z t WHZ 0 30 0 35 ns 5 Data to write time overlap t DW 40 — 40 — ns Data hold from write time t DH 0 — 0 — ns Output active from end of write t OW 5 — 5 — ns Output disable to output in high-Z t OHZ 0 30 0 35 ns 5 Notes: 1. A write occurs during the overlap of a low CS1, and high CS2, and a high WE. A write begins at the latest transition among CS1 going low,CS2 going high and WE going low. A write ends at the earliest transition among CS1 going high CS2 going low and WE going high. Time tWP is measured from the beginning of write to the end of write. 2. t CW is measured from the later of CS1 going low or CS2 going high to the end of write. 3. t AS is measured from the address valid to the beginning of write. 4. t WR is measured from the earliest of CS1 or WE going high or CS2 going low to the end of write cycle. 5. During this period, I/O pins are in the output state, therefore the input signals of the opposite phase to the outputs must not be applied. 6. In the write cycle with OE low fixed, tWP must satisfy the following equation to avoid a problem of data bus contention t WP ≥ tWHZ max + tDW min. HM6264B Series Write Timing Waveform (1) (OE Clock) tWC Address Valid address OE tCW tWR CS1 *1 CS2 tAW tAS tWP WE tOHZ Dout Din Note: 1. tDW High Impedance High Impedance tDH Valid data If CS1 goes low or CS2 goes high simultaneously with WE going low or after WE going low, the outputs remain in the high impedance state. HM6264B Series Write Timing Waveform (2) (OE Low Fixed) (OE = VIL ) tWC Address Valid address tAW tWR tCW CS1 *1 CS2 tWP WE tAS tOH tOW tWHZ *2 Dout tDW *3 tDH *4 Din Notes: 1. 2. 3. 4. High Impedance Valid data If CS1 goes low simultaneously with WE going low or after WE goes low, the outputs remain in high impedance state. Dout is the same phase of the written data in this write cycle. Dout is the read data of the next address. If CS1 is low and CS2 is high during this period, I/O pins are in the output state. Input signals of opposite phase to the outputs must not be applied to I/O pins. HM6264B Series Low VCC Data Retention Characteristics (Ta = 0 to +70°C) Parameter Symbol Min Typ*1 Max Unit Test conditions*4 VCC for data retention VDR 2.0 — — V CS1 ≥ VCC –0.2 V, CS2 ≥ VCC –0.2 V or CS2 ≤ 0.2 V Data retention current I CCDR — 1*1 25*2 µA VCC = 3.0 V, 0 V ≤ Vin ≤ VCC CS1 ≥ VCC –0.2 V, CS2 ≥ VCC –0.2 V or 0 V ≤ CS2 ≤ 0.2 V Chip deselect to data retention time t CDR 0 — — ns See retention waveform Operation recovery time tR t RC*3 — — ns Notes: 1. 2. 3. 4. Reference data at Ta = 25°C. 10 µA max at Ta = 0 to + 40°C. t RC = read cycle time. CS2 controls address buffer, WE buffer, CS1 buffer, OE buffer, and Din buffer. If CS2 controls data retention mode, Vin levels (address, WE, OE, CS1, I/O) can be in the high impedance state. If CS1 controls data retention mode, CS2 must be CS2 ≥ VCC – 0.2 V or 0 V ≤ CS2 ≤ 0.2 V. The other input levels (address, WE, OE, I/O) can be in the high impedance state. Low V CC Data Retention Timing Waveform (1) (CS1 Controlled) tCDR tR Data retention mode VCC 4.5 V 2.2 V VDR CS1 CS1 ≥ VCC – 0.2 V 0V Low V CC Data Retention Timing Waveform (2) (CS2 Controlled) Data retention mode VCC 4.5 V tCDR tR CS2 VDR 0.4 V 0V CS2 ≤ 0.2 V HM6264B Series Package Dimensions HM6264BLP Series (DP-28) Unit: mm 35.6 36.5 Max 15 13.4 14.6 Max 28 14 1.2 15.24 2.54 ± 0.25 0.48 ± 0.10 0.51 Min 1.9 Max 2.54 Min 5.7 Max 1 + 0.11 0.25 – 0.05 0° – 15° HM6264B Series HM6264BLSP Series (DP-28N) Unit: mm 36.00 37.32 Max 6.60 14 1.30 7.62 0.51 Min 5.08 Max 2.20 Max 2.54 ± 0.25 0.48 ± 0.10 2.54 Min 1 7.00 Max 15 28 + 0.11 0.25 – 0.05 0° – 15° HM6264BLTM Series (FP-28DA) Unit: mm 18.3 18.75 Max 15 3.0 Max 14 11.8 ± 0.3 0.17 1 0.895 + 0.08 – 0.07 8.4 28 + 0.10 0.40 – 0.05 0.1 Min 0 – 10 ° 1.27 ± 0.10 1.0 HM6264B Series When using this document, keep the following in mind: 1. This document may, wholly or partially, be subject to change without notice. 2. All rights are reserved: No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without Hitachi’s permission. 3. Hitachi will not be held responsible for any damage to the user that may result from accidents or any other reasons during operation of the user’s unit according to this document. 4. Circuitry and other examples described herein are meant merely to indicate the characteristics and performance of Hitachi’s semiconductor products. Hitachi assumes no responsibility for any intellectual property claims or other problems that may result from applications based on the examples described herein. 5. No license is granted by implication or otherwise under any patents or other rights of any third party or Hitachi, Ltd. 6. MEDICAL APPLICATIONS: Hitachi’s products are not authorized for use in MEDICAL APPLICATIONS without the written consent of the appropriate officer of Hitachi’s sales company. Such use includes, but is not limited to, use in life support systems. Buyers of Hitachi’s products are requested to notify the relevant Hitachi sales offices when planning to use the products in MEDICAL APPLICATIONS. Hitachi, Ltd. Semiconductor & IC Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100, Japan Tel: Tokyo (03) 3270-2111 Fax: (03) 3270-5109 For further information write to: Hitachi America, Ltd. Semiconductor & IC Div. 2000 Sierra Point Parkway Brisbane, CA. 94005-1835 USA Tel: 415-589-8300 Fax: 415-583-4207 Hitachi Europe GmbH Electronic Components Group Continental Europe Dornacher Straße 3 D-85622 Feldkirchen München Tel: 089-9 91 80-0 Fax: 089-9 29 30 00 Hitachi Europe Ltd. Electronic Components Div. Northern Europe Headquarters Whitebrook Park Lower Cookham Road Maidenhead Berkshire SL6 8YA United Kingdom Tel: 0628-585000 Fax: 0628-778322 Hitachi Asia Pte. Ltd. 16 Collyer Quay #20-00 Hitachi Tower Singapore 0104 Tel: 535-2100 Fax: 535-1533 Hitachi Asia (Hong Kong) Ltd. Unit 706, North Tower, World Finance Centre, Harbour City, Canton Road Tsim Sha Tsui, Kowloon Hong Kong Tel: 27359218 Fax: 27306071