HT82V805 CCD 4 Channel Vertical Driver Features · Input voltage: 3.0V~5.5V - 2-level output: 1 circuit for shutter driver output voltage level (typ.) = -9V to 15V · Built-in seven circuits - 2-level output: · Switchable between NTSC (EIA) and PAL (CCIR) 2 circuits for vertical CCD clock driver output voltage level (typ.) = -9V to 0V - 3-level output: 2 circuits for vertical CCD clock driver output voltage level (typ.) = -9V to 15V modes · 16-pin SSOP, 16/20-pin TSSOP package General Description HT82V805 is a CMOS vertical clock driver and shutter driver IC for CCD area sensors. It has the capability of converting the voltage and impedance from the CMOS level. Block Diagram V S S V H P O F D O F D X V L V 2 V 2 X V 1 X V 1 A V H 1 A X V M E V 3 X V 3 A V H 3 A X V 4 X V 4 V H + D C O U T - D C IN Rev. 1.10 1 December 29, 2005 HT82V805 Pin Assignment V S S 1 2 0 V H O F D X 2 1 9 P O F D V S S 1 1 6 V H V 2 X 3 1 8 V L O F D X 2 1 5 P O F D V 1 X 4 1 7 V 2 V 2 X 3 1 4 V L V H 1 A X 5 1 6 V 1 A V 1 X 4 1 3 V 2 V 3 X 6 1 5 V M E V H 1 A X 5 1 2 V 1 A V H 3 A X 7 1 4 V 3 A V 3 X 6 1 1 V M E V 4 X 8 1 3 V 4 V H 3 A X 7 1 0 V 3 A N C 9 1 2 V H V 4 X 8 9 V 4 1 0 1 1 D C O U T D C IN H T 8 2 V 8 0 5 1 6 S S O P -A /T S S O P -A H T 8 2 V 8 0 5 2 0 T S S O P -A Pin Description Pin Name VSS I/O ¾ Description Negative power supply, ground OFDX I Electronic shutter pulse input V1X, V2X, V3X, V4X I Vertical transfer pulse input VH1AX, VH3AX I Pulse that transfers the charge of the photo-diode to the vertical shift register. NC ¾ No connection DCIN I OP-Amp input (internal pull-down resistor) DCOUT O OP-Amp output VH ¾ Power supply for high level of V1A, V3A V4 O Pulse to drive vertical CCD shift register (2 level: VME, VL) V3A O Pulse to drive vertical CCD shift register (3 level: VME, VL, VH) VME ¾ Power supply for intermediate level of V1A, V3A V1A O Pulse to drive vertical CCD shift register (3 level: VME, VL, VH) V2 O Pulse to drive vertical CCD shift register (2 level: VME, VL) VL ¾ Power supply for all low level output pulses POFD O Electronic shutter pulse output (2 level: VL, VH) Rev. 1.10 2 December 29, 2005 HT82V805 Absolute Maximum Ratings Supply Voltage .............................VSS-0.3V to VL+35V Storage Temperature ...........................-55°C to 150°C Input Voltage ...............................VSS-0.3V to VH+0.3V Operating Temperature ..........................-25°C to 70°C Note: These are stress ratings only. Stresses exceeding the range specified under ²Absolute Maximum Ratings² may cause substantial damage to the device. Functional operation of this device at other conditions beyond those listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability. Recommended Operating Conditions Symbol Parameter Value VH VL Supply Voltage VME V1A, V2, V3A, V4, POFD Output Voltage Unit -0.3 ~ VL+35 V 0 ~ -10 V VL-0.3 ~ 3.0 V VL-0.3 ~ VH+0.3 V Logic Function Table Input Output V1X, V3X VH1AX, VH3AX V2X, V4X OFDX V1A, V3A V2, V4 POFD L L ¾ ¾ VH ¾ ¾ H L ¾ ¾ Z ¾ ¾ L H ¾ ¾ VME ¾ ¾ H H ¾ ¾ VL ¾ ¾ ¾ ¾ L ¾ ¾ VME ¾ ¾ ¾ H ¾ ¾ VL ¾ ¾ ¾ ¾ L ¾ ¾ VH ¾ ¾ ¾ H ¾ ¾ VL Rev. 1.10 3 December 29, 2005 HT82V805 D.C. Characteristics Symbol Parameter VH=15V, VL=-9V, VME=0V, Ta=25°C Test Conditions Min. Typ. Max. Unit VDD Logic Supply Voltage ¾ 3.0 3.3 5.5 V VH Supply Voltage ¾ 14.5 15 15.5 V VL Supply Voltage ¾ -9.5 -8.5 -7.5 V VIH High Level Input Voltage ¾ 2.4 ¾ ¾ V VIL Low Level Input Voltage ¾ ¾ ¾ 1.2 V ¾ 3.8 ¾ mA ¾ -2 ¾ mA ¾ -6.5 ¾ mA IVH IVL Operating Current Shutter speed=100kHz IVME IOL V1A, V2, V3A, V4=-9.0V ¾ 37 ¾ mA IOM1 V1A, V2, V3A, V4=-0.5V ¾ -15 ¾ mA V1A, V3A=0.5V ¾ 13.5 ¾ mA IOH V1A, V3A=14.5V ¾ -18 ¾ mA IOSL OFDX=-8.0V ¾ 18 ¾ mA IOSH OFDX=14.5V ¾ -10.5 ¾ mA DCIN=1~3V 3.4 3.9 4.2 V/V IOM2 G Output Current OP-Amp Gain A.C. Characteristics Symbol Parameter Ta=25°C Test Conditions Min. Typ. Max. Unit tPLM VH=15V, VL=-8.5V, VME=0V ¾ 55 80 ns tPMH VH=15V, VL=-8.5V, VME=0V ¾ 50 90 ns VH=15V, VL=-8.5V, VME=0V ¾ 55 100 ns tPML VH=15V, VL=-8.5V, VME=0V ¾ 45 130 ns tPHM VH=15V, VL=-8.5V, VME=0V ¾ 50 120 ns tPHL VH=15V, VL=-8.5V, VME=0V ¾ 55 100 ns tTLM VH=15V, VL=-8.5V, VME=0V ¾ 370 900 ns tTMH VH=15V, VL=-8.5V, VME=0V ¾ 785 900 ns VH=15V, VL=-8.5V, VME=0V ¾ 70 140 ns tTML VH=15V, VL=-8.5V, VME=0V ¾ 300 700 ns tTHM VH=15V, VL=-8.5V, VME=0V ¾ 630 960 ns tTHL VH=15V, VL=-8.5V, VME=0V ¾ 45 120 ns tPLH tTLH Rev. 1.10 Delay Time Rising Time 4 December 29, 2005 HT82V805 Timing Diagrams V 5 V , V 1 X V 2 X , V 3 X 5 0 % 4 X G N D 5 0 % (0 .0 V ) 5 V V H , V H 1 A X 5 0 % 3 A X G N D (0 .0 V ) V tP L M tT (1 5 .0 V ) H tT V 1 A , V V 3 A M E V V 2 , V (0 .0 V ) M E tP L M tP M H tT 9 0 % M H 1 0 % 9 0 % H M H M tP 9 0 % tT (0 .0 V ) tP L M M L 9 0 % tP tT M L 1 0 % 1 0 % (- 9 .0 V ) L V 5 0 % H L L M 1 0 % tT 9 0 % H L 9 0 % 4 L 1 0 % 1 0 % (- 9 .0 V ) V 5 V O F D X 5 0 % G N D 5 0 % (0 .0 V ) tP tP L H tT V (1 5 .0 V ) H V L tT L H 9 0 % P O F D H L 9 0 % 1 0 % (- 9 .0 V ) H L 1 0 % Application Circuits V T im in g G e n e ra to r 1 (1 5 V ) (-9 V ) V H P O F D V L V 2 X 4 V 2 V 1 X X V 1 5 X S G 1 6 X V 3 7 X S G 3 8 X V 4 9 1 0 (5 V ) L O F D X 3 X V 2 D D H V S S 2 X S U B V V V H 1 A X V 1 A V 3 X V M E V H 3 A X V 3 A V 4 X V 4 N C V H D C IN D C O U T 2 0 C C D 1 m F 1 9 1 8 0 .1 m F 1 7 V S U B V 2 1 6 V 1 1 5 1 4 V 3 1 3 V 4 1 2 1 1 0 .1 m F H T 8 2 V 8 0 5 4 7 k W 0 .1 m F Rev. 1.10 5 December 29, 2005 HT82V805 Equivalent Circuits V 1 5 0 0 p F V 2 7 W 1 5 0 0 p F 2 7 W 1 A 2 7 W 2 7 W 1 5 0 0 p F 2 3 3 0 0 p F V 4 P O F D 1 5 0 0 p F 3 3 0 0 p F 3 3 0 0 p F V 5 0 0 p F 3 A 3 3 0 0 p F 5 W Rev. 1.10 6 December 29, 2005 HT82V805 Package Information 16-pin SSOP (150mil) Outline Dimensions 9 1 6 A B 1 8 C C ' G H D E Symbol Rev. 1.10 a F Dimensions in mil Min. Nom. Max. A 228 ¾ 244 B 150 ¾ 157 C 8 ¾ 12 C¢ 189 ¾ 197 D 54 ¾ 60 E ¾ 25 ¾ F 4 ¾ 10 G 22 ¾ 28 H 7 ¾ 10 a 0° ¾ 8° 7 December 29, 2005 HT82V805 16-pin TSSOP Outline Dimensions 1 6 9 E 1 1 8 E D L A R A 2 0 .1 0 B e C q A 1 y (4 C O R N E R S ) Symbol Rev. 1.10 Dimensions in mm Min. Nom. Max. A 1 ¾ 1.05 A1 0.05 ¾ 0.15 A2 1.05 ¾ 1.2 B ¾ 0.25 ¾ C 0.11 ¾ 0.15 D 4.9 ¾ 5.1 E 6.2 ¾ 6.6 E1 4.3 ¾ 4.5 e ¾ 0.65 ¾ L 0.5 ¾ 0.7 y ¾ ¾ 0.076 q 0° ¾ 8° 8 December 29, 2005 HT82V805 20-pin TSSOP Outline Dimensions 2 0 1 1 E 1 1 1 0 E D L A R A 2 0 .1 0 e C A 1 B q y (4 C O R N E R S ) Symbol Rev. 1.10 Dimensions in mm Min. Nom. Max. A 1.05 ¾ 1.2 A1 0.05 ¾ 0.15 A2 0.95 ¾ 1.05 B ¾ 0.22 ¾ C 0.13 ¾ 0.17 D 6.4 ¾ 6.6 E 6.3 ¾ 6.5 E1 4.3 ¾ 4.5 e ¾ 0.65 ¾ L 0.45 ¾ 0.75 y ¾ ¾ 0.1 q 0° ¾ 8° 9 December 29, 2005 HT82V805 Product Tape and Reel Specifications Reel Dimensions D T 2 A C B T 1 SSOP 16S Symbol Description Dimensions in mm A Reel Outer Diameter 330±1.0 B Reel Inner Diameter 62±1.5 C Spindle Hole Diameter 13.0+0.5 -0.2 D Key Slit Width 2.0±0.5 T1 Space Between Flange 12.8+0.3 -0.2 T2 Reel Thickness 18.2±0.2 TSSOP 16L Symbol Description Dimensions in mm A Reel Outer Diameter 330±1 B Reel Inner Diameter 62±1.5 C Spindle Hole Diameter 13+0.5 -0.2 D Key Slit Width 2±0.5 T1 Space Between Flange 16.8+0.3 -0.2 T2 Reel Thickness 22.2±0.2 Rev. 1.10 10 December 29, 2005 HT82V805 Carrier Tape Dimensions P 0 D P 1 t E F W C D 1 B 0 P K 0 A 0 SSOP 16S Symbol Description Dimensions in mm W Carrier Tape Width 12.0+0.3 -0.1 P Cavity Pitch 8.0±0.1 E Perforation Position 1.75±0.1 F Cavity to Perforation (Width Direction) 5.5±0.1 D Perforation Diameter 1.55±0.1 D1 Cavity Hole Diameter 1.5+0.25 P0 Perforation Pitch 4.0±0.1 P1 Cavity to Perforation (Length Direction) 2.0±0.1 A0 Cavity Length 6.4±0.1 B0 Cavity Width 5.2±0.1 K0 Cavity Depth 2.1±0.1 t Carrier Tape Thickness C Cover Tape Width 0.30±0.05 9.3 TSSOP 16L Symbol Description W Carrier Tape Width P Cavity Pitch E Perforation Position Dimensions in mm 16+0.3 -0.1 8±0.1 1.75±0.1 F Cavity to Perforation (Width Direction) 7.5±0.5 D Perforation Diameter 1.5+0.1 D1 Cavity Hole Diameter 1.5+0.1 P0 Perforation Pitch 4±0.1 P1 Cavity to Perforation (Length Direction) 2±0.1 A0 Cavity Length 6.8±0.1 B0 Cavity Width 5.4±0.1 K0 Cavity Depth t Carrier Tape Thickness C Cover Tape Width Rev. 1.10 1.6±0.1 0.3±0.013 13.3 11 December 29, 2005 HT82V805 Holtek Semiconductor Inc. (Headquarters) No.3, Creation Rd. II, Science Park, Hsinchu, Taiwan Tel: 886-3-563-1999 Fax: 886-3-563-1189 http://www.holtek.com.tw Holtek Semiconductor Inc. (Taipei Sales Office) 4F-2, No. 3-2, YuanQu St., Nankang Software Park, Taipei 115, Taiwan Tel: 886-2-2655-7070 Fax: 886-2-2655-7373 Fax: 886-2-2655-7383 (International sales hotline) Holtek Semiconductor Inc. (Shanghai Sales Office) 7th Floor, Building 2, No.889, Yi Shan Rd., Shanghai, China 200233 Tel: 021-6485-5560 Fax: 021-6485-0313 http://www.holtek.com.cn Holtek Semiconductor Inc. (Shenzhen Sales Office) 5/F, Unit A, Productivity Building, Cross of Science M 3rd Road and Gaoxin M 2nd Road, Science Park, Nanshan District, Shenzhen, China 518057 Tel: 0755-8616-9908, 8616-9308 Fax: 0755-8616-9533 Holtek Semiconductor Inc. (Beijing Sales Office) Suite 1721, Jinyu Tower, A129 West Xuan Wu Men Street, Xicheng District, Beijing, China 100031 Tel: 010-6641-0030, 6641-7751, 6641-7752 Fax: 010-6641-0125 Holtek Semiconductor Inc. (Chengdu Sales Office) 709, Building 3, Champagne Plaza, No.97 Dongda Street, Chengdu, Sichuan, China 610016 Tel: 028-6653-6590 Fax: 028-6653-6591 Holmate Semiconductor, Inc. (North America Sales Office) 46729 Fremont Blvd., Fremont, CA 94538 Tel: 510-252-9880 Fax: 510-252-9885 http://www.holmate.com Copyright Ó 2005 by HOLTEK SEMICONDUCTOR INC. The information appearing in this Data Sheet is believed to be accurate at the time of publication. However, Holtek assumes no responsibility arising from the use of the specifications described. The applications mentioned herein are used solely for the purpose of illustration and Holtek makes no warranty or representation that such applications will be suitable without further modification, nor recommends the use of its products for application that may present a risk to human life due to malfunction or otherwise. Holtek¢s products are not authorized for use as critical components in life support devices or systems. Holtek reserves the right to alter its products without prior notification. For the most up-to-date information, please visit our web site at http://www.holtek.com.tw. Rev. 1.10 12 December 29, 2005