INA163 SBOS177D – NOVEMBER 2000 – REVISED MAY 2005 Low-Noise, Low-Distortion INSTRUMENTATION AMPLIFIER FEATURES DESCRIPTION ● ● ● ● ● ● ● The INA163 is a very low-noise, low-distortion, monolithic instrumentation amplifier. Its current-feedback circuitry achieves very wide bandwidth and excellent dynamic response over a wide range of gain. It is ideal for low-level audio signals such as balanced lowimpedance microphones. Many industrial, instrumentation, and medical applications also benefit from its low noise and wide bandwidth. Unique distortion cancellation circuitry reduces distortion to extremely low levels, even in high gain. The INA163 provides near-theoretical noise performance for 200Ω source impedance. Its differential input, low noise, and low distortion provide superior performance in professional microphone amplifier applications. The INA163’s wide supply voltage, excellent output voltage swing, and high output current drive allow its use in high-level audio stages as well. The INA163 is available in a space-saving SO-14 surface-mount package, specified for operation over the –40°C to +85°C temperature range. LOW NOISE: 1nV/√Hz at 1kHz LOW THD+N: 0.002% at 1kHz, G = 100 WIDE BANDWIDTH: 800kHz at G = 100 WIDE SUPPLY RANGE: ±4.5V to ±18V HIGH CMR: > 100dB GAIN SET WITH EXTERNAL RESISTOR SO-14 SURFACE-MOUNT PACKAGE APPLICATIONS ● PROFESSIONAL MICROPHONE PREAMPS ● MOVING-COIL TRANSDUCER AMPLIFIERS ● DIFFERENTIAL RECEIVERS ● BRIDGE TRANSDUCER AMPLIFIERS VO1 1 INA163 VIN− 4 3 6kΩ 6kΩ A1 Sense 8 3kΩ RG A3 3kΩ VO 9 G=1+ 12 VIN+ 6kΩ 6kΩ A2 6000 RG Ref 10 5 14 VO 2 11 V+ 6 V− Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. Copyright © 2000–2005, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. www.ti.com ELECTROSTATIC DISCHARGE SENSITIVITY PIN CONFIGURATION Top View This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. VO1 1 14 VO2 NC 2 13 NC GS1 3 12 GS2 VIN− 4 11 V+ VIN+ 5 10 Ref V− 6 9 VO NC 7 8 Sense NC = No Internal Connection ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. ABSOLUTE MAXIMUM RATINGS(1) Power Supply Voltage ....................................................................... ±18V Signal Input Terminals, Voltage(2) .................. (V–) – 0.5V to (V+) + 0.5V Current(2) .................................................... 10mA Output Short-Circuit to Ground ............................................... Continuous Operating Temperature .................................................. –55°C to +125°C Storage Temperature ..................................................... –55°C to +125°C Junction Temperature .................................................................... +150°C Lead Temperature (soldering, 10s) ............................................... +300°C NOTES: (1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified is not implied. (2) Input terminals are diode-clamped to the power-supply rails. Input signals that can swing more than 0.5V beyond the supply rails should be current limited to 10mA or less. PACKAGE/ORDERING INFORMATION(1) PRODUCT PACKAGE-LEAD DESIGNATOR MARKING INA163UA SO-14 Surface Mount D INA163UA NOTE: (1) For the most current package and ordering information, see the Package Option Addendum located at the end of this document, or see the TI web site at www.ti.com. INA163 2 www.ti.com SBOS177D ELECTRICAL CHARACTERISTICS: VS = ±15V TA = +25°C and at rated supplies, VS = ±15V, RL = 2kΩ connected to ground, unless otherwise noted. INA163UA PARAMETER CONDITIONS MIN GAIN Range Gain Equation(1) Gain Error, G = 1 G = 10 G = 100 G = 1000 Gain Temp Drift Coefficient, G = 1 G > 10 Nonlinearity, G = 1 G = 100 INPUT STAGE NOISE Voltage Noise fO = 1kHz fO = 100Hz fO = 10Hz Current Noise fO = 1kHz 1 to 10000 G = 1 + 6k/RG ±0.1 ±0.2 ±0.2 ±0.5 ±1 ±25 ±0.0003 ±0.0006 INPUT VOLTAGE RANGE Common-Mode Voltage Range Common-Mode Rejection, G = 1 G = 100 MAX UNITS V/V ±0.25 ±0.7 ±10 ±100 % % % % ppm/°C ppm/°C % of FS % of FS RSOURCE = 0Ω OUTPUT STAGE NOISE Voltage Noise, fO = 1kHz INPUT OFFSET VOLTAGE Input Offset Voltage vs Temperature vs Power Supply TYP VCM = VOUT = 0V TA = TMIN to TMAX VS = ±4.5V to ±18V VIN+ – VIN– = 0V VIN+ – VIN– = 0V VCM = ±11V, RSRC = 0Ω 1 1.2 2 nV/√Hz nV/√Hz nV/√Hz 0.8 pA/√Hz 60 nV/√Hz 50 + 2000/G 1 + 20/G 1 + 50/G (V+) – 4 (V–) + 4 70 100 INPUT BIAS CURRENT Initial Bias Current vs Temperature Initial Offset Current vs Temperature 250 + 5000/G 3 + 200/G (V+) – 3 (V–) + 3 80 116 2 10 0.1 0.5 µV µV/°C µV/V V V dB dB 12 1 µA nA/°C µA nA/°C INPUT IMPEDANCE DYNAMIC RESPONSE Bandwidth, Small Signal, –3dB, G = 1 G = 100 Slew Rate THD+Noise, f = 1kHz Settling Time, 0.1% 0.01% Overload Recovery OUTPUT Voltage Load Capacitance Stability Short-Circuit Current POWER SUPPLY Rated Voltage Voltage Range Current, Quiescent Differential Common-Mode 60 2 60 2 MΩ pF MΩ pF G = 100 G = 100, 10V Step G = 100, 10V Step 50% Overdrive 3.4 800 15 0.002 2 3.5 1 kHz V/µs % µs µs µs (V+) – 1.8 (V–) + 1.8 1000 ±60 V V pF mA RL = 2kΩ to Gnd (V+) – 2 (V–) + 2 Continuous-to-Common ±4.5 IO = 0mA TEMPERATURE RANGE Specification Operating θJA ±15 ±10 –40 –40 ±18 ±12 +85 +125 100 V V mA °C °C °C/W NOTE: (1) Gain accuracy is a function of external RG. INA163 SBOS177D www.ti.com 3 TYPICAL CHARACTERISTICS At TA = +25°C, VS = 5V, VCM = 1/2 VS, RL = 25kΩ, CL = 50pF, unless otherwise noted. GAIN vs FREQUENCY THD+N vs FREQUENCY 70 0.1 60 VO = 5Vrms RL = 10kΩ G = 1000 G = 1000 50 G = 100 30 20 0.01 THD+N (%) Gain (dB) 40 G = 10 10 G = 100 0.001 0 G = 10 G=1 −10 G=1 −20 0.0001 10k 100k 1M 10M 20 100 1k Frequency (Hz) NOISE VOLTAGE (RTI) vs FREQUENCY CURRENT NOISE SPECTRAL DENSITY 10 100 Current Noise Density (pA/√Hz) Noise (RTI) (nV/√Hz) 1k G=1 G = 10 10 G = 500 G = 1000 G = 100 1 0.1 1 10 100 1k 10k 1 10 100 Frequency (Hz) 1k 10k Frequency (Hz) COMMON- MODE REJECTION vs FREQUENCY POWER-SUPPLY REJECTION vs FREQUENCY 140 140 G = 1000 Power-Supply Rejection (dB) 120 Input Referred CMR (dB) 10k 20k Frequency (Hz) G = 100 100 G = 10 80 G=1 60 40 20 0 120 G = 100, 1000 G = 10 100 G=1 80 60 40 20 0 10 100 1k 10k 100k 1M 1 Frequency (Hz) 10 100 1k 10k 100k 1M Frequency (Hz) INA163 4 www.ti.com SBOS177D TYPICAL CHARACTERISTICS (Cont.) At TA = +25°C, VS = 5V, VCM = 1/2 VS, RL = 25kΩ, CL = 50pF, unless otherwise noted. OUTPUT VOLTAGE SWING vs OUTPUT CURRENT SETTLING TIME vs GAIN V+ 10 20V Step 8 (V+) − 4 Settling Time (µs) Output Voltage to Rail (V) (V+) − 2 (V+) − 6 (V−) + 6 (V−) + 4 0.01% 6 4 2 (V−) + 2 0.1% 0 V− 10 20 30 40 50 60 1 10 100 Gain SMALL-SIGNAL TRANSIENT RESPONSE (G = 1) SMALL-SIGNAL TRANSIENT RESPONSE (G = 100) 1000 20mV/div Output Current (mA) 20mV/div 0 LARGE-SIGNAL TRANSIENT RESPONSE (G = 1) LARGE-SIGNAL TRANSIENT RESPONSE (G = 100) 5V/div 10µs/div 5V/div 2.5µs/div 2.5µs/div 2.5µs/div INA163 SBOS177D www.ti.com 5 APPLICATIONS INFORMATION temperature drift. These effects can be inferred from the gain equation. Make a short, direct connection to the gain set resistor, RG. Avoid running output signals near these sensitive input nodes. Figure 1 shows the basic connections required for operation. Power supplies should be bypassed with 0.1µF tantalum capacitors near the device pins. The output Sense (pin 8) and output Reference (pin 10) should be low-impedance connections. Resistance of a few ohms in series with these connections will degrade the common-mode rejection of the INA163. NOISE PERFORMANCE The INA163 provides very low-noise with low-source impedance. Its 1nV/√Hz voltage noise delivers neartheoretical noise performance with a source impedance of 200Ω. The input stage design used to achieve this low noise, results in relatively high input bias current and input bias current noise. As a result, the INA163 may not provide the best noise performance with a source impedance greater than 10kΩ. For source impedance greater than 10kΩ, other instrumentation amplifiers may provide improved noise performance. GAIN-SET RESISTOR Gain is set with an external resistor, RG, as shown in Figure 1. The two internal 3kΩ feedback resistors are laser-trimmed to 3kΩ within approximately ±0.2%. Gain is: G = 1+ 6000 RG The temperature coefficient of the internal 3kΩ resistors is approximately ±25ppm/°C. Accuracy and TCR of the external RG will also contribute to gain error and V+ 0.1µF 1 VIN− 4 11 INA163 6kΩ 6kΩ A1 3 Sense 8 3kΩ A3 RG 9 3kΩ VO G=1+ 12 VIN+ 6kΩ 6kΩ Ref A2 10 5 14 6 0.1µF V− V+ RG 6000 RG GAIN (V/V) (dB) 1 0 2 6 5 14 10 20 20 26 50 34 100 40 200 46 500 54 1000 60 2000 66 RG (Ω) NC(1) 6000 1500 667 316 122 61 30 12 6 3 NOTE: (1) NC = No Connection. Sometimes Shown in Simplified Form: INA163 VO V− FIGURE 1. Basic Circuit Connections. INA163 6 www.ti.com SBOS177D INPUT CONSIDERATIONS OFFSET VOLTAGE TRIM Very low source impedance (less than 10Ω) can cause the INA163 to oscillate. This depends on circuit layout, signal source, and input cable characteristics. An input network consisting of a small inductor and resistor, as shown in Figure 2, can greatly reduce any tendency to oscillate. This is especially useful if a variety of input sources are to be connected to the INA163. Although not shown in other figures, this network can be used as needed with all applications shown. A variable voltage applied to pin 10, as shown in Figure 3, can be used to adjust the output offset voltage. A voltage applied to pin 10 is summed with the output signal. An op amp connected as a buffer is used to provide a low impedance at pin 10 to assure good common-mode rejection. V+ 47Ω 11 VIN− 1.2µH 8 INA163 12 VIN+ 6 An output sense terminal allows greater gain accuracy in driving the load. By connecting the sense connection at the load, I • R voltage loss to the load is included inside the feedback loop. Current drive can be increased by connecting a buffer amp inside the feedback loop, as shown in Figure 4. 4 3 1.2µH OUTPUT SENSE VO 9 10 +15V 5 47Ω V− 4 11 Sense FIGURE 2. Input Stabilization Network. INA163 9 10 5 V+ 4 12 5 BW 6 −15V 8 INA163 RG VO BUF634 BUF634 connected for wide bandwidth. 11 3 ±250mA Output Drive 8 VO 9 V+ 10 6 100µA FIGURE 4. Buffer for Increase Output Current. V− 150Ω OPA237 10kΩ 150Ω 100µA V− FIGURE 3. Offset Voltage Adjustment Circuit. INA163 SBOS177D www.ti.com 7 Phantom Power +48V R3 47k + 47 F +15V R1 6.8k 0.1 F R2 6.8k 1N4148 C1(1) 47 F 60V + 1 Female XLR Connector R6(2) 5 3 2 A1 INA163 C2(1) 47 F 60V + 9 VO 10 1M R7(3) 1k R4 2.2k 8 R5 2.2k 0.1 F 0.1 F 1N4148 A2 OPA134 NOTES: (1) Use non-polar capacitors if phantom power is to be turned off. (2) R6 sets maximum gain. (3) R7 sets minimum gain. 15V 15V Optional DC Output Control Loop FIGURE 5. Phantom-Powered Microphone Preamplifier. MICROPHONE AMPLIFIER Figure 5 shows a typical circuit for a professional microphone input amplifier. R1 and R2 provide a current path for conventional 48V phantom power source for a remotely located microphone. An optional switch allows phantom power to be disabled. C1 and C2 block the phantom power voltage from the INA163 input circuitry. Non-polarized capacitors should be used for C1 and C2 if phantom power is to be disabled. For additional input protection against ESD and hot-plugging, four INA4148 diodes may be connected from the input to supply lines. R4 and R5 provide a path for input bias current of the INA163. Input offset current (typically 100nA) creates a DC differential input voltage that will produce an output offset voltage. This is generally the dominant source of output offset voltage in this application. With a maximum gain of 1000 (60dB), the output offset voltage can be several volts. This may be entirely acceptable if the output is AC-coupled into the subsequent stage. An alternate technique is shown in Figure 5. An inexpensive FET-input op amp in a feedback loop drives the DC output voltage to 0V. A2 is not in the audio signal path and does not affect signal quality. Gain is set with a variable resistor, R7, in series with R6. R6 determines the maximum gain. The total resistance, R6 + R7, determines the lowest gain. A special reverse-log taper potentiometer for R7 can be used to create a linear change (in dB) with rotation. INA163 8 www.ti.com SBOS177D PACKAGE OPTION ADDENDUM www.ti.com 8-Aug-2006 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty INA163UA ACTIVE SOIC D 14 58 Pb-Free (RoHS) CU NIPDAU Level-3-260C-168 HR INA163UA/2K5 ACTIVE SOIC D 14 2500 Pb-Free (RoHS) CU NIPDAU Level-3-260C-168 HR INA163UA/2K5E4 ACTIVE SOIC D 14 2500 Pb-Free (RoHS) CU NIPDAU Level-3-260C-168 HR INA163UAE4 ACTIVE SOIC D 14 58 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Low Power Wireless www.ti.com/lpw Mailing Address: Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2006, Texas Instruments Incorporated