USB Port Power Supply Controller ISL6186 Features The ISL6186 USB power controller family provides overcurrent (OC) fault protection for one or more USB ports. • 2.5V to 5V Operating Range This product family consists of eight individual functional product variants and three package options and is operation rated for a nominal +2.5V to +5V range and specified over the full commercial and industrial temperature ranges. • Continuous Current Options for 1.5A, 3A and 3.6A Each ISL6186 type incorporates a 45mΩ P-channel MOSFET power switch for power control and features internal current monitoring, accurate current limiting, and current limited delay to turn-off for system supply protection along with control and communication I/O. • Output Discharges with Reverse Current Blocking When Disabled The ISL6186 family offers product variants with specified continuous output current levels of 1.5A, 3A or 3.6A, enable active high or low inputs, and latch off or automatic retry after overcurrent turn-off, making these devices well suited for many low-power applications. This family of ICs is offered in an industry standard SOIC package as well as in the 70% smaller 3x3 DFN package, which provides the same performance and an additional Power-Good output feature in the smallest possible (10 Ld DFN) package. • 45mΩ Integrated Power P-channel MOSFET Switches • Thermally Insensitive 12ms of Current Limiting Prior to Turn-Off • Latch-off or Auto Restart and Enable Polarity Options • 1µA Off-State Supply Current • Industry Standard Pin-for-Pin SOIC and Smaller DFN Packages Available Applications • USB Port Power Management Including USB 3.0 • Low Power Electronic Circuit Limiting and Breaker D+ D- C O N T R O L L E R USB PORT 1 OUT ENABLE 1.2 FAULT +5V VIN GND ISL6186 VBUS D+ DUSB PORT POWER FIGURE 1. TYPICAL APPLICATION September 1, 2011 FN7698.1 1 1.3 VBUS USB PORT_2 NORMALIZED rDS(ON) U S B 1.1 1.0 0.9 0.8 0.7 -40 -25 0 25 45 75 85 115 TEMPERATURE (°C) FIGURE 2. NORMALIZED rDS(ON) TEMPERATURE CHARACTERISTIC CURVE CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas Inc. 2011. All Rights Reserved Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries. All other trademarks mentioned are the property of their respective owners. ISL6186 Simplified Block Diagram GND PGD -VCOMP PGD only on 10DFN + OUT VIN POR VIN OUT CURRENT AND TEMP. MONITORING, GATE, DELAY AND OUTPUT CONTROL LOGIC EN FAULT Pin Configurations ISL6186 (10 LD DFN) TOP VIEW ISL6186 (8 LD SOIC/DFN) TOP VIEW GND VIN VIN EN/EN 1 2 3 8 (GND) EPAD DFN ONLY 4 7 6 5 OUT OUT OUT GND 1 10 PGD VIN 2 9 OUT VIN 3 8 OUT VIN 4 EN/EN 5 (GND) EPAD 7 OUT 6 FLT FLT Pin Descriptions PIN NUMBER 8 Ld SOIC/DFN 10 Ld DFN SYMBOL 1 1 GND IC ground reference 2, 3 2, 3, 4 VIN Chip bias, Controlled Voltage Input, Undervoltage Lock Out (UVLO). VIN provides chip bias voltage. At VIN < 1.7V, chip functionality is disabled, FLT is active and floating and OUT is held low. Range 0V to 5.5V 4 5 EN/EN 2 DESCRIPTION Enable/Disable inputs, Active high (EN) and active low (EN) options enable the power switch. These inputs have internal 1MΩ pull-off resistors. Range 0V to VIN FN7698.1 September 1, 2011 ISL6186 Pin Descriptions (Continued) PIN NUMBER 8 Ld SOIC/DFN 10 Ld DFN SYMBOL DESCRIPTION 5 6 FLT Overcurrent Fault Indicator. Overcurrent fault indicator. FLT floats and is disabled until VIN > VUVLO. This output is pulled low after the current limit time-out period has expired. Fault is not signaled due to over-temperature shut down. Range 0V to VIN 6, 7, 8 7, 8, 9 OUT Controlled Supply Output. Upon an OC condition, IOUT is current limited. Current limit response time is within 200µs. This output will remain in current limit for a nominal 12ms before being turned off either for the latch or auto retry versions. Range 0V to VIN - 10 PGD Open drain Power-Good output that pulls low 40ms after VOUT = 90% of VIN and rises after VOUT< 85% of VIN. Range 0V to VIN PD (DFN only) PD EPAD Thermal Dissipation Exposed PAD Range: Connect to GND. Ordering Information PART NUMBER (Notes 1, 2, 3) VIN = 5V MAXIMUM CONTINUOUS IOUT LATCH/ POWER- GOOD (A) AUTO RETRY OUTPUT PART MARKING EN/EN INPUT TEMP. RANGE (°C) PACKAGE (Pb-free) PKG. DWG. # ISL61861ACBZ 61861A CBZ EN 1.5 LATCH NO 0 to +70 8 Ld SOIC M8.15 ISL61861BCBZ 61861B CBZ EN 1.5 RETRY NO 0 to +70 8 Ld SOIC M8.15 ISL61861CCBZ 61861C CBZ EN 3 LATCH NO 0 to +70 8 Ld SOIC M8.15 ISL61861DCBZ 61861D CBZ EN 3 RETRY NO 0 to +70 8 Ld SOIC M8.15 ISL61861ECBZ 61861E CBZ EN 1.5 LATCH NO 0 to +70 8 Ld SOIC M8.15 ISL61861FCBZ 61861F CBZ EN 1.5 RETRY NO 0 to +70 8 Ld SOIC M8.15 ISL61861GCBZ 61861G CBZ EN 3 LATCH NO 0 to +70 8 Ld SOIC M8.15 ISL61861HCBZ 61861H CBZ EN 3 RETRY NO 0 to +70 8 Ld SOIC M8.15 ISL61862ACRZ 62AC EN 1.5 LATCH NO 0 to +70 8 Ld DFN L8.3x3J ISL61862BCRZ 62BC EN 1.5 RETRY NO 0 to +70 8 Ld DFN L8.3x3J ISL61862CCRZ 62CC EN 3 LATCH NO 0 to +70 8 Ld DFN L8.3x3J ISL61862DCRZ 62DC EN 3 RETRY NO 0 to +70 8 Ld DFN L8.3x3J ISL61862ECRZ 62EC EN 1.5 LATCH NO 0 to +70 8 Ld DFN L8.3x3J ISL61862FCRZ 62FC EN 1.5 RETRY NO 0 to +70 8 Ld DFN L8.3x3J ISL61862GCRZ 62GC EN 3 LATCH NO 0 to +70 8 Ld DFN L8.3x3J ISL61862HCRZ 62HC EN 3 RETRY NO 0 to +70 8 Ld DFN L8.3x3J ISL61863ACRZ 63AC EN 1.5 LATCH YES 0 to +70 10 Ld DFN L10.3x3 ISL61863BCRZ 63BC EN 1.5 RETRY YES 0 to +70 10 Ld DFN L10.3x3 ISL61863CCRZ 63CC EN 3 LATCH YES 0 to +70 10 Ld DFN L10.3x3 ISL61863DCRZ 63DC EN 3 RETRY YES 0 to +70 10 Ld DFN L10.3x3 ISL61863ECRZ 63EC EN 1.5 LATCH YES 0 to +70 10 Ld DFN L10.3x3 ISL61863FCRZ 63FC EN 1.5 RETRY YES 0 to +70 10 Ld DFN L10.3x3 ISL61863GCRZ 63GC EN 3 LATCH YES 0 to +70 10 Ld DFN L10.3x3 ISL61863HCRZ 63HC EN 3 RETRY YES 0 to +70 10 Ld DFN L10.3x3 ISL61863ICRZ 63IC EN 3.6 LATCH YES 0 to +70 10 Ld DFN L10.3x3 3 FN7698.1 September 1, 2011 ISL6186 Ordering Information (Continued) PART NUMBER (Notes 1, 2, 3) PART MARKING EN/EN INPUT VIN = 5V MAXIMUM CONTINUOUS IOUT LATCH/ POWER- GOOD (A) AUTO RETRY OUTPUT TEMP. RANGE (°C) PACKAGE (Pb-free) PKG. DWG. # ISL61863JCRZ 63JC EN 3.6 RETRY YES 0 to +70 10 Ld DFN L10.3x3 ISL61863KCRZ 63KC EN 3.6 LATCH YES 0 to +70 10 Ld DFN L10.3x3 ISL61863LCRZ 63LC EN 3.6 RETRY YES 0 to +70 10 Ld DFN L10.3x3 ISL61861AIBZ 61861A IBZ EN 1.5 LATCH NO -40 to +85 8 Ld SOIC M8.15 ISL61861BIBZ 61861B IBZ EN 1.5 RETRY NO -40 to +85 8 Ld SOIC M8.15 ISL61861CIBZ 61861C IBZ EN 3 LATCH NO -40 to +85 8 Ld SOIC M8.15 ISL61861DIBZ 61861D IBZ EN 3 RETRY NO -40 to +85 8 Ld SOIC M8.15 ISL61861EIBZ 61861E IBZ EN 1.5 LATCH NO -40 to +85 8 Ld SOIC M8.15 ISL61861FIBZ 61861F IBZ EN 1.5 RETRY NO -40 to +85 8 Ld SOIC M8.15 ISL61861GIBZ 61861G IBZ EN 3 LATCH NO -40 to +85 8 Ld SOIC M8.15 ISL61861HIBZ 61861H IBZ EN 3 RETRY NO -40 to +85 8 Ld SOIC M8.15 ISL61862AIRZ 62AI EN 1.5 LATCH NO -40 to +85 8 Ld DFN L8.3x3J ISL61862BIRZ 62BI EN 1.5 RETRY NO -40 to +85 8 Ld DFN L8.3x3J ISL61862CIRZ 62CI EN 3 LATCH NO -40 to +85 8 Ld DFN L8.3x3J ISL61862DIRZ 62DI EN 3 RETRY NO -40 to +85 8 Ld DFN L8.3x3J ISL61862EIRZ 62EI EN 1.5 LATCH NO -40 to +85 8 Ld DFN L8.3x3J ISL61862FIRZ 62FI EN 1.5 RETRY NO -40 to +85 8 Ld DFN L8.3x3J ISL61862GIRZ 62GI EN 3 LATCH NO -40 to +85 8 Ld DFN L8.3x3J ISL61862HIRZ 62HI EN 3 RETRY NO -40 to +85 8 Ld DFN L8.3x3J ISL61863AIRZ 63AI EN 1.5 LATCH YES -40 to +85 10 Ld DFN L10.3x3 ISL61863BIRZ 63BI EN 1.5 RETRY YES -40 to +85 10 Ld DFN L10.3x3 ISL61863CIRZ 63CI EN 3 LATCH YES -40 to +85 10 Ld DFN L10.3x3 ISL61863DIRZ 63DI EN 3 RETRY YES -40 to +85 10 Ld DFN L10.3x3 ISL61863EIRZ 63EI EN 1.5 LATCH YES -40 to +85 10 Ld DFN L10.3x3 ISL61863FIRZ 63FI EN 1.5 RETRY YES -40 to +85 10 Ld DFN L10.3x3 ISL61863GIRZ 63GI EN 3 LATCH YES -40 to +85 10 Ld DFN L10.3x3 ISL61863HIRZ 63HI EN 3 RETRY YES -40 to +85 10 Ld DFN L10.3x3 ISL61863IIRZ 63II EN 3.6 LATCH YES -40 to +85 10 Ld DFN L10.3x3 ISL61863JIRZ 63JI EN 3.6 RETRY YES -40 to +85 10 Ld DFN L10.3x3 ISL61863KIRZ 63KI EN 3.6 LATCH YES -40 to +85 10 Ld DFN L10.3x3 ISL61863LIRZ 63LI EN 3.6 RETRY YES -40 to +85 10 Ld DFN L10.3x3 ISL61861AEVAL1Z (ISL61861C) EN 3 LATCH NO - 8 Ld SOIC EVAL BD ISL61862HEVAL1Z (ISL61862F) EN 1.5 RETRY NO - 8 Ld DFN EVAL BD ISL61863LEVAL1Z (ISL61863L) EN 3.6 RETRY YES - 10 Ld DFN EVAL BD NOTES: 1. Add “-T*” suffix for tape and reel. Please refer to TB347 for details on reel specifications. 2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 3. For Moisture Sensitivity Level (MSL), please see device information page for ISL6186. For more information on MSL please see Tech Brief TB363. 4 FN7698.1 September 1, 2011 ISL6186 Absolute Maximum Ratings Thermal Information Supply Voltage (VIN to GND, Note 7) . . . . . . . . . . . . . . . . . . . . . . . . . . . .6.5V EN, FAULT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .VIN OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND - 0.3V to VIN 0.3V Output Current . . . . . . . . . . . . . . . . . Short Circuit Protected; Limited to 5A ESD Rating Human Body Model (Per MIL-STD-883 Method 3015.7) . . . . . . . . . . 3kV Machine Model (Per MIL-STD-883 Method 3015.7) . . . . . . . . . . . . 300V Latch Up (Tested per JESD-78B; Class 2, Level A) . . . . . . . . . . . . . . 100mA Thermal Resistance (Typical) θJA (°C/W) θJC (°C/W) 8 Lead SOIC Package (Note 4) . . . . . . . . . . 120 N/A 8 Lead 3x3 DFN Package (Notes 5, 6) . . . 48 6 10 Lead 3x3 DFN Package (Notes 5, 6) . . 48 6 Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . +150°C Maximum Storage Temperature Range . . . . . . . . . . . . . . -65°C to +150°C Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Operating Conditions Commercial Temperature Range . . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C Industrial Temperature Range . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C Supply Voltage Range (Typical). . . . . . . . . . . . . . . . . . . . . . . . . 2.5V to 5.5V CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 4. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. 5. θJA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech Brief TB379. 6. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside. 7. All voltages are relative to GND, unless otherwise specified. Electrical Specifications VIN = 5V, TA = TJ, Unless Otherwise Specified. Boldface limits apply over the operating temperature range, 0°C to +75°C or -40°C to +85°C. SYMBOL PARAMETER TEST CONDITIONS MIN (Note 8) TYP MAX (Note 8) UNITS - 45 48 mΩ - 50 54 mΩ - 54 57 mΩ POWER SWITCH rDS(ON)_50 ON-Resistance at 5.0V (Pulse Tested) VIN = 5V, IOUT = 0.5A, TA = TJ = +25°C TA = TJ = +85°C rDS(ON)_33 ON-Resistance at 3.3V (Pulse Tested) VIN = 3.3V, IOUT = 0.5A, TA = TJ = +25°C rDS(ON)_25 On Resistance at 2.5V (Pulse Tested) VIN = 2.5V, IOUT = 0.5A, TA = TJ = +25°C TA = TJ = +85°C - 61 64 mΩ - 65 69 mΩ TA = TJ = +85°C - 74 79 mΩ - 22 45 mV 3.4 5 6 kΩ VOUT_DIS Disabled Output Voltage VIN = 5V, Switch Disabled, 50µA Load ROUT_PD Output Pull-Down Resistor VIN = 5V, Switch Disabled tR VOUT Rise Time RL = 10Ω, CL = 10µF, 10% to 90% - 10 - µs tF Slow VOUT Turn-off Fall Time RL = 10Ω, CL = 10µF, 90% to 10% - 200 - µs ISL6186xA, B, E, F - - 1.5 A ISL6186xC, D, G, H - - 3.0 A ISL6186xI, J, K, L (10 Ld DFN) - - 3.6 A ISL6186xA, B, E, F - - 1.5 A ISL6186xC, D, G, H - - 2.5 A ISL61861I, J, K, L (10 Ld DFN) - - 2.7 A ISL6186xA, B, E, F - 1.2 - A ISL61861C, D, G, H (SOIC) - 1.8 - A IOUT_CONT_2 ISL61862, ISL61863 C, D, G, H (DFN) - 2 - A IOUT_CONT_2 ISL61863I, J, K, L (10 Ld DFN) - 2 - A CURRENT CONTROL IOUT_CONT_5 IOUT_CONT_5 IOUT_CONT_5 IOUT_CONT_3 IOUT_CONT_3 IOUT_CONT_3 IOUT_CONT_2 IOUT_CONT_2 Maximum Continuous Current, VIN = 5V Guaranteed by the Minimum Itrip Current Specification Maximum Continuous Current, VIN = 3.3V Guaranteed by the Minimum Itrip Current Specification Maximum Continuous Current, VIN = 2.5V 5 FN7698.1 September 1, 2011 ISL6186 Electrical Specifications VIN = 5V, TA = TJ, Unless Otherwise Specified. Boldface limits apply over the operating temperature range, 0°C to +75°C or -40°C to +85°C. (Continued) MIN (Note 8) TYP MAX (Note 8) UNITS ISL6186xA, B, E, F 1.7 2.5 3.3 A ITRIP_5 ISL6186xC, D, G, H 3.0 3.9 4.5 A ITRIP_5 ISL61863I, J, K, L (10 Ld DFN) 3.7 3.9 5.0 A ISL6186xA, B, E, F 1.7 2.1 2.7 A ITRIP_3 ISL6186xC, D, G, H 2.8 3.5 4.0 A ITRIP_3 ISL61863I, J, K, L (10 Ld DFN) 3.5 3.9 4.3 A ISL6186xA, B, E, F - 1.8 - A ITRIP_2 ISL6186xC, D, G, H - 3.2 - A ITRIP_2 ISL61863I, J, K, L (10 Ld DFN) - 3.4 - A SYMBOL ITRIP_5 ITRIP_3 ITRIP_2 PARAMETER Trip Current, VIN = 5V Trip Current, VIN = 3.3V Trip Current, VIN = 2.5V ISL6186xA, B, E, F, VIN - VOUT = 1V 1.37 1.6 1.81 A ILIM_5 ISL6186xC, D, G, H, VIN - VOUT = 1V 2.82 3.1 3.42 A ILIM_5 ISL61863I, J, K, L, (10 Ld DFN) VIN - VOUT = 1V 3.24 3.6 4.00 A ISL6186xA, B, E, F, VIN - VOUT = 1V 1.35 1.5 1.77 A ISL6186xC, D, G, H, VIN - VOUT = 1V 2.72 3.0 3.35 A ILIM_5 ILIM_3 Current Limit, VIN = 5V TEST CONDITIONS Current Limit, VIN = 3.3V ILIM_3 ISL61863I, J, K, L (10 Ld DFN), VIN - VOUT = 1V 3.22 3.5 3.95 A ISL6186xA, B, E, F, VIN - VOUT = 1V 1.30 1.5 1.70 A ILIM_2 ISL6186xC, D, G, H, VIN - VOUT = 1V 2.55 2.9 3.14 A ILIM_2 ISL61863I, J, K, L (10 Ld DFN), VIN - VOUT = 1V 3.07 3.3 3.75 A ISL6186xA, B, E, F, VOUT = 0V 1.45 2.0 2.35 A ISL6186xC, D, G, H, VOUT = 0V 2.60 3.4 4.50 A ILIM_3 ILIM_2 Isc_5 Current Limit, VIN = 2.5V Short Circuit Current, VIN = 5V Isc_5 ISL61863I, J, K, L (10 Ld DFN), VOUT = 0V 2.48 3.5 5.00 A ISL6186XA, B, E, F, VOUT = 0V 0.95 1.2 1.50 A Isc_3 ISL6186XC, D, G, H, VOUT = 0V 1.95 2.2 2.70 A Isc_3 ISL61863I, J, K, L (10 Ld DFN), VOUT = 0V 2.00 2.5 3.00 A ISL6186xA, B, E, F, VOUT = 0V - 1.1 - A Isc_2 ISL6186xC, D, G, H, VOUT = 0V - 2.1 - A Isc_2 ISL61863I, J, K, L, (10 Ld DFN) VOUT = 0V - 2.4 - A OC to Limit Settling Time VIN/RL = 2ILIM, CL = 10µF to within 10% of ILIM - 200 - µs Severe OC to Limit Settling Time VIN/RL = 4ILIM, CL = 10µF to within 10% of ILIM - 30 - µs tCL Current Limit Duration IOUT = ILIM 9.2 12 15 ms tRTY Automatic Retry Period 0.80 1 1.35 s - - 0.45 V - 5 - µA Isc_5 Isc_3 Isc_2 tsettIlim tsettIlim_sev Short Circuit Current, VIN = 3.3V Short Circuit Current, VIN = 2.5V I/O PARAMETERS Vfault_lo Ifault Venr_5 Hys_Venr_5 Venr_3 Hys_Venr_3 Venr_2 Hys_Venr_2 Fault Output Voltage Fault IOUT = 10mA Fault Leakage ENABLE/ENABLE Rising Threshold VIN = 5V 1.5 1.8 2 V EN/EN Threshold Hysteresis VIN = 5V 65 140 175 mV ENABLE/ENABLE Rising Threshold VIN = 3.3V 1.0 1.3 1.6 V EN/EN Threshold Hysteresis VIN = 3.3V 30 80 120 mV ENABLE/ENABLE Rising Threshold VIN = 2.5V 0.95 1.1 1.3 V EN/EN Threshold Hysteresis VIN = 2.5V 10 70 110 mV 6 FN7698.1 September 1, 2011 ISL6186 Electrical Specifications VIN = 5V, TA = TJ, Unless Otherwise Specified. Boldface limits apply over the operating temperature range, 0°C to +75°C or -40°C to +85°C. (Continued) SYMBOL PARAMETER TEST CONDITIONS MIN (Note 8) TYP MAX (Note 8) UNITS Ren_h ENABLE Pull-Down Resistor Enable asserted high options 0.6 1 1.55 MΩ Ren_l ENABLE Pull-Up Resistor Enable asserted low options 0.6 1 1.55 MΩ tON Enable to Output Turn-on Time RL = 10Ω, CL = 10µF, Enable 50% to Output 90% - 0.1 - ms tOFF Enable to Output Turn-off Time RL = 10Ω, CL = 10µF, Enable 50% to Output 10% - 0.25 - ms tpdPGr Enable to Power Good Output Rising Time Disable to Power-Good De-assert - 30 - ns PG Vth Power Good Threshold PGD pulls low when VOUT/VIN 88 91 95 % PGN Vth Power Not Good Threshold PGD release high when VOUT/VIN 78 86 93 % tVthr2PG PG Vth to PG Falling PG delay after PG Vth - 1.5 - µs tVthf2PG PGN Vth to PG Rising PG delay after PGN Vth - 45 - µs BIAS PARAMETERS IVDD Enabled VIN Current Switches Closed, OUTPUT = OPEN - 57 75 µA IVDD Disabled VIN Current Switches Open, OUTPUT = OPEN - 3.5 5.5 µA VUVLO Rising POR Threshold VIN Rising to functional operation - 2.1 2.3 V Reverse Blocking Leakage Current VIN = 0V, VOUT = 5V - 0.3 2.0 µA IVR Temp_dis Over-Temperature Disable - 150 - °C Temp_hys Over-Temperature Hysteresis - 20 - °C NOTE: 8. Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design. Introduction The ISL6186 is a single channel overcurrent (OC) fault protection IC for the +2.5V to +5V environment. Each ISL6186 has a 45mΩ P-channel MOSFET power switch for power control. An enabling input and fault reporting output compatible with 2.5V to 5V logic allows for external control and reporting. This device features an integrated power switch with current monitoring, accurate current limiting, reverse bias protection, and current limited timed delay to turn-off for system reliability. See Figures 11 through 27 for typical operational waveforms including both undercurrent and overcurrent situations. The ISL6186 offers current sense and limiting with VIN = 5V to guarantee continuous current levels of 1.5A, 3A and 3.6A, making these devices well suited for a myriad of USB and other low-power (18W max) port power management applications and configurations. The ISL6186 also provides thermally insensitive timed OC turn-off and fault notification, isolating and protecting the voltage bus in the event of a peripheral OC or short circuit independent of the ambient thermal condition. The ISL6186 undervoltage lockout feature prevents turn-on of the output unless the correct ENABLE state and VIN > VUVLO are present. During initial turn-on, the ISL6186 prevents false fault reporting by blanking the fault signal. 7 During operation, once an OC condition is detected, the output is current limited for tCL to allow transient OC conditions to pass. If still in current limit after the current limit period has elapsed, the output is then turned off and the fault is reported by pulling the FAULT output low. On the latch-off options, after turn-off, both the output and the FAULT signal are latched low until reset by the enable signal being de-asserted or a POR occurring. At this time, the FAULT signal will clear and the switch is ready to be turned back on. On the auto restart options, the ISL6186 will attempt to periodically turn on the output as long as the enable is asserted. When disabled, the ISL6186 has a low quiescent supply current and output to input reverse current flow blocking capability. The ISL6186 family is provided with enable polarity options and an industry standard 8 Ld SOIC pinout along with two versions in the 70% smaller 3x3 DFN. The 8 Ld DFN package offers the same performance as the 8 Ld SOIC whereas the 10 Ld DFN offers higher current capability in the smallest possible package due to its lower package electrical and thermal resistance. Additionally, the 10 Ld DFN has a Power-Good output PGD that pulls low 40ms after VOUT>90% of VIN and rises after VOUT< 85% of VIN. FN7698.1 September 1, 2011 ISL6186 Functional Description Over-Temperature Shutdown Power On Reset (POR) Although the ISL6186 has an over-temperature shutdown and lockout feature because of the 12ms timed shutdown, the thermal shutdown is likely only to be invoked in extremely high ambient temperatures. FAULT does not respond to OT events. The ISL6186 POR feature inhibits device functionality when VIN <VUVLO. Reverse Polarity Protection In any event in which the power switch is disabled or powered down, and VOUT > VIN, there will be no output to input current flow, nor will the output voltage appear on the input. The over- temperature protection invokes and disables the switch turn-on operation. Once the die temperature is ~+140°C, it will turn off an already on switch at ~+150°C and releases the part to operation once the die temperature falls to ~+120°C. Turn-off Time Delay Soft-Start Upon enable, the voltage on the VOUT pin will ramp up according to the equation: ILIM/COUT (V/s). Resistive or active load will slow the VOUT ramp-up toward the top of its curve. Fault Blanking On Start-Up During initial turn-on, the ISL6186 prevents nuisance faults being reported to the system controller by blanking the fault signal until the internal FET is fully enhanced. Current Trip and Limiting Levels The ISL6186 provides integrated current sensing in the MOSFET, which allows for rapid control of OC events. Once an OC condition is detected, the ISL6186 goes into its current limiting (CL) control mode. The ISL6186 is variant specified to allow a continuous current (ICONT) operation of 1.5A, 3A or 3.6A. As the current increases past its continuous current rating, it will reach a level that causes the device to enter its current limit mode; that is, the current trip level. The current trip level is in all cases adequately above the ICONT rating so as not to cause unintended false faults. The current limit is specified at VOUT = VIN - 1V to test a known representative condition and is featured at a nominal value slightly higher than the continuous current rating. The speed of this current limiting control is inversely related to the magnitude of the OC fault. Thus, a hard overcurrent is more quickly pulled to its limiting value than a marginal OC condition. During operation, once an OC condition is detected, the output is current limited for ~12ms to allow transient OC conditions to pass. If still in current limit and after the current limit period has elapsed, the output is then turned off, and the fault is reported by pulling the FAULT output low. The internal 12ms timer starts upon current limiting and is independent of ambient or IC thermal conditions, thus providing more consistent operation over the entire temperature range. Latch-off Restart/Auto-Restart Start After turn-off, with the latch-off options, both the output and the FAULT signal are latched low until reset by the enable signal being de-asserted, at which time the FAULT signal will clear and the IC is ready for enable to assert. On the auto-restart options, the ISL6186 will attempt to periodically turn on the output at approximately 1s intervals as long as the enable is asserted. If the OC condition remains indefinitely, so will the fault indication and the restart attempts, until such time as the thermal protection feature is invoked, thus increasing the restart period. Power-Good Output This feature is an active low, open-drain, power-good indicator that asserts after VOUT/VIN>90% and de-asserts when VOUT/VIN < 85%. It immediately de-asserts upon the IC being disabled. Active Output Pull-down Another ISL6186 feature is the 10kΩ active pull-down on the outputs to <60mV above GND when the device is disabled, thus ensuring discharge of the load. Typical Performance Curves 1.3 85 75 VIN = 2.5V 70 65 60 VIN = 3.3V 55 50 VIN = 5V 45 NORMALIZED rDS(ON) rDS(ON) @ 0.5A (mΩ) 80 1.2 1.1 1.0 0.9 0.8 40 35 -40 -25 0 25 45 75 TEMPERATURE (°C) 85 FIGURE 3. SWITCH ON-RESISTANCE AT 0.5A 8 115 0.7 -40 -25 0 25 45 75 TEMPERATURE (°C) 85 115 FIGURE 4. NORMALIZED SWITCH RESISTANCE FN7698.1 September 1, 2011 ISL6186 Typical Performance Curves (Continued) 4.0 3.0 2.5 3.3V ITRIP 2.0 5V Isc 2.5V ITRIP 1.5 5V ILIM 3.3V ILIM 2.5V ILIM 3.3V ISC 1.0 -40 3.5 OUTPUT CURRENT (A) OUTPUT CURRENT (A) 5V ITRIP 3.0 1.5 1.75 1.70 4.0 3.3V ITRIP 5V ILIM 3.5 3.3V ILIM 2.5V ITRIP 2.5V ILIM 3.0 3.3V ISC 2.5V ISC -40 25 TEMPERATURE (°C) 85 +3SIGMA TYPICAL -3SIGMA 1.55 1.50 1.45 1.40 -40 3.90 3A CONTINUOUS IOUT VERSION 3.2 3.1 +3SIGMA 3.85 TYPICAL 3.80 -3SIGMA 3.0 2.9 2.8 25 TEMPERATURE (°C) 3.6A CONTINUOUS IOUT VERSION +3SIGMA 3.75 3.70 TYPICAL 3.65 3.60 -3SIGMA 3.55 -40 25 85 TEMPERATURE (°C) FIGURE 9. LIMITING CURRENT ±3 SIGMA, VIN = 5V 9 85 FIGURE 8. LIMITING CURRENT ±3 SIGMA, VIN = 5V. ILIMIT ± 3 SIGMA (A) ILIMIT ± 3 SIGMA (A) 1.5A CONTINUOUS IOUT VERSION 1.60 1.30 85 3.4 2.7 25 TEMPERATURE (°C) 1.35 FIGURE 7. 3.6A CONTINUOUS CURRENT CHARACTERISTICS 3.3 -40 1.65 ILIMIT ± 3 SIGMA (A) OUTPUT CURRENT (A) 5V ISC 2.0 2.5V ISC FIGURE 6. 3A CONTINUOUS CURRENT CHARACTERISTICS 4.5 2.5 2.5V ILIM 3.3V ISC 2.0 85 FIGURE 5. 1.5A CONTINUOUS CURRENT CHARACTERISTICS 5V ILIM 3.3V ITRIP 5V ISC 3.3V ILIM 2.5 2.5V ITRIP 2.5V ISC 25 TEMPERATURE (°C) 5V ITRIP 3.50 -40 25 85 TEMPERATURE (°C) FIGURE 10. LIMITING CURRENT ±3 SIGMA, VIN = 5V FN7698.1 September 1, 2011 ISL6186 Typical Performance Curves (Continued) EN EN FAULT FAULT VOUT VOUT Iin IIN FIGURE 11. 1.5A VARIANT ILIM WAVEFORM FIGURE 12. 3A VARIANT ILIM WAVEFORM FAULT FAULT PG PG EN VOUT VOUT IIN IIN FIGURE 13. 3.6A VARIANT I LIM WAVEFORM w PG EN FIGURE 14. LISL6186 TURN-ON w PG EN CL=100µF CL=10µF CL=100µF CL=10µF FIGURE 15. VOUT TURN-ON/RISE TIME vs CLOAD. VIN = 5.5V, RL = 10Ω 10 FIGURE 16. VOUT TURN-OFF/FALL TIME vs CLOAD. VIN = 5.5V, RL = 10Ω FN7698.1 September 1, 2011 ISL6186 Typical Performance Curves (Continued) 3A VARIANT 3A VARIANT 4A OC 32µs 78A/ms 2A OC 60µs 16A/ms 1.6A/ms 1A OC 137µs 0.5A OC 300µs ILIMIT = 3.42A ILOAD = 2.75A ILOAD = 3.2A ILIMITED FIGURE 18. PEAK CURRENT SETTLING TIMES FIGURE 17. OC RAMP RATE ILIM WAVEFORMS EN EN FAULT FAULT VOUT VOUT IIN IIN 3A VARIANT 3A VARIANT FIGURE 20. TURN-ON INTO MOMENTARY OC FIGURE 19. TURN-ON INTO AN OVERCURRENT EN VOUT FAULT PG VOUT EN IIN IIN FIGURE 21. OVERCURRENT RETRY FUNCTION 11 FIGURE 22. TURN-OFF w PG FN7698.1 September 1, 2011 ISL6186 Typical Performance Curves (Continued) EN EN VOUT VOUT IIN = 3.8A IIN Rl =1.3W, Cl = 200µF 3.6A VARIANT FIGURE 24. TURN-ON INTO TO 18WLOAD FIGURE 23. VIN = 2.4V TURN-ON INTO 0.88Ω Test Circuits + V 10k 10k FLT FLT 5V VIN OUT ISL6186 OUTPUT 10µF EN 5V VIN ISL6186 EN 10 OUTPUT OUT RL sized for desired OC level RL 10µF 10 rDS(ON) = V/(VOUT/10Ω) FIGURE 25B. CURRENT LIMITING FIGURE 25A. rDS(ON) FIGURE 25. DC TEST CIRCUIT VIN EN 0.5VIN 0.5VIN 10k 0V tON FLT 5V 0-VIN VIN OUT ISL6186 EN OUTPUT 10µF OUTPUT tOFF VIN 90% 10% 10 90% OUTPUT 10% tR FIGURE 26A. TRANSIENT TEST CIRCUIT 12 GND VIN 90% 10% -GND tF FIGURE 27. TRANSIENT WAVEFORM MEASUREMENT POINTS FN7698.1 September 1, 2011 ISL6186 ISL61863EVAL1Z Schematic and Photo GND GND PG * VIN OUT EN FLT NOTE: *PGD Output only available on ISL61863 types FIGURE 28A. ISL61863EVAL1Z SCHEMATIC FIGURE 28B. ISL61863EVAL1Z BOARD PHOTO FIGURE 28. ISL61863EVAL1Z SCHEMATIC and ISL61863EVAL1Z PHOTOGRAPH Application Information Using the ISL6186EVAL1Z Platform General and Biasing Information There are three evaluation platforms for the ISL6186 family. There is one for each package style, each with a different continuous output current level and representing a mix of enable polarity and output retry or latch options. The standard available evaluation board options are listed at the end of the Ordering Information table, which starts on page 3. Figure 28A illustrates the schematic for the 10 Ld DFN ISL61863EVAL1Z. Other than the unique PGOOD output on the ISL61863 types, all the schematics and functions are the same across all three package types. Consult the individual package pinouts on page 2 for those differences. The evaluation platform is biased and monitored through a few labeled test points. See Table 1 for test point assignments and descriptions. TABLE 1. ISL61863EVAL1Z TEST POINT ASSIGNMENTS TP NAME DESCRIPTION GND Eval Board and IC Gnd VIN Eval Board, IC Bias and Power Input EN Enable Switch OUT Switch Power Output PG Power-Good Output FLT Fault Output Upon proper bias of the evaluation platform and correct enabling of the IC, the ISL6186 will have a nominal VIN/5.1Ω load current that is below the continuous current rating passing through each enabled switch. See Figures 14 to 16 for typical ISL6186 turn-on and turn-off waveforms. External current loading in excess of the trip current level for the particular part being evaluated will result in the ISL6186 entering 13 current limiting mode. Figure 11 illustrates current limiting mode for the ISL6186 product variants with 1.5A of continuous load current rating. The scope shot shows current limiting for ~12ms before it is turned off and the fault signal is asserted. Application Considerations See Table 2 for a listing of ISL6186XEVAL1Z board components. Decoupling VIN Application considerations for the ISL6186 family are widely accepted best industry practices. Good decoupling practices on the VIN pin must be followed by placement close to the IC, with at least 2.2µF being recommended. For the 3.0 and 3.6A versions, at least 33µF is recommended to prevent spiking and glitching on VIN during an OC event. Use good PCB layout practices to reduce input and output inductance to the ISL6186. Loading VOUT When designing with the 3A and 3.6A versions in an implementation in which the output may be unloaded (open) while the ISL6186 is turned on, a minimum of 4.7µF of capacitive loading is recommended to prevent high dv/dt from unnecessarily activating the surge/ESD circuitry. Continuous Current Ratings The ISL6186 provides several continuous current rated devices specified at VIN = 5V: these are the 1.5A, 3A and 3.6A options, which are capable over the entire temperature extreme. At VIN = 3.3V, current capability is degraded, and the ISL6186 is specified at 1.5A and 3A. At VIN = 2.5V, there are no specifications, but a typical value is provided in the specification table as guidance for +25°C operation. This degraded capability is due to the higher rDS(ON) of the FET switch at the lower bias voltage. Enhanced thermal characteristics and an increased number of bond wires allows the 10 Ld DFN to have a higher current capability than either the 8 Ld SOIC or 8 Ld DFN. FN7698.1 September 1, 2011 ISL6186 TABLE 2. ISL6186XEVAL1Z BOARD COMPONENT LISTING COMPONENT DESIGNATOR COMPONENT FUNCTION COMPONENT DESCRIPTION U1 ISL6186 Intersil, ISL6186 R1 Output Load Resistor 5.1Ω, 5%, 3W R2 FLT Output Pull-up Resistor 10kΩ, 0805 R3 * only on ISL61863EVAL1Z PGD Output Pull-up Resistor 10kΩ, 0805 C1 Decoupling Capacitor 2.2μF on ISL61862EVAL1Z 33μF on ISL61861EVAL1Z and ISL61863EVAL1Z C2 Load Capacitor 10µF 16V Electrolytic, Radial Lead 14 FN7698.1 September 1, 2011 ISL6186 Revision History The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make sure you have the latest Rev. DATE REVISION 9/1/11 FN7698.1 CHANGE Initial release to web. Products Intersil Corporation is a leader in the design and manufacture of high-performance analog semiconductors. The Company's products address some of the industry's fastest growing markets, such as, flat panel displays, cell phones, handheld products, and notebooks. Intersil's product families address power management and analog signal processing functions. Go to www.intersil.com/products for a complete list of Intersil product families. *For a complete listing of Applications, Related Documentation and Related Parts, please see the respective device information page on intersil.com: ISL6186 To report errors or suggestions for this datasheet, please go to www.intersil.com/askourstaff FITs are available from our website at http://rel.intersil.com/reports/search.php For additional products, see www.intersil.com/product_tree Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems as noted in the quality certifications found at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 15 FN7698.1 September 1, 2011 ISL6186 Package Outline Drawing L8.3x3J 8 LEAD DUAL FLAT NO-LEAD PLASTIC PACKAGE Rev 0 9/09 2X 1.950 3.00 B 0.15 8 5 3.00 (4X) 6X 0.65 A 1.64 +0.10/ - 0.15 6 PIN 1 INDEX AREA 4 8X 0.30 8X 0.400 ± 0.10 TOP VIEW 6 PIN #1 INDEX AREA 1 4 0.10 M C A B 2.38 +0.10/ - 0.15 BOTTOM VIEW SEE DETAIL "X" ( 2.38 ) ( 1.95) 0.10 C Max 1.00 C 0.08 C SIDE VIEW ( 8X 0.60) (1.64) ( 2.80 ) PIN 1 C 0 . 2 REF 5 (6x 0.65) 0 . 00 MIN. 0 . 05 MAX. ( 8 X 0.30) DETAIL "X" TYPICAL RECOMMENDED LAND PATTERN NOTES: 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994. 3. Unless otherwise specified, tolerance : Decimal ± 0.05 4. Dimension applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 5. Tiebar shown (if present) is a non-functional feature. 6. 16 The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. FN7698.1 September 1, 2011 ISL6186 Package Outline Drawing L10.3x3 10 LEAD DUAL FLAT PACKAGE (DFN) Rev 6, 09/09 3.00 6 PIN #1 INDEX AREA A B 1 6 PIN 1 INDEX AREA (4X) 3.00 2.00 8x 0.50 2 10 x 0.23 4 0.10 1.60 TOP VIEW 10x 0.35 BOTTOM VIEW 4 (4X) 0.10 M C A B 0.415 PACKAGE OUTLINE 0.200 0.23 0.35 (10 x 0.55) SEE DETAIL "X" (10x 0.23) 1.00 MAX 0.10 C BASE PLANE 2.00 0.20 C SEATING PLANE 0.08 C SIDE VIEW (8x 0.50) C 0.20 REF 5 1.60 0.05 TYPICAL RECOMMENDED LAND PATTERN DETAIL "X" NOTES: 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994. 3. Unless otherwise specified, tolerance : Decimal ± 0.05 4. Lead width applies to the metallized terminal and is measured between 0.18mm and 0.30mm from the terminal tip. 5. Tiebar shown (if present) is a non-functional feature. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 indentifier may be either a mold or mark feature. 17 FN7698.1 September 1, 2011 ISL6186 Package Outline Drawing M8.15 8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE Rev 3, 3/11 DETAIL "A" 1.27 (0.050) 0.40 (0.016) INDEX 6.20 (0.244) 5.80 (0.228) AREA 0.50 (0.20) x 45° 0.25 (0.01) 4.00 (0.157) 3.80 (0.150) 1 2 8° 0° 3 0.25 (0.010) 0.19 (0.008) SIDE VIEW “B” TOP VIEW 2.20 (0.087) SEATING PLANE 5.00 (0.197) 4.80 (0.189) 1.75 (0.069) 1.35 (0.053) 1 8 2 7 0.60 (0.023) 1.27 (0.050) 3 6 4 5 -C- 1.27 (0.050) 0.51(0.020) 0.33(0.013) SIDE VIEW “A 0.25(0.010) 0.10(0.004) 5.20(0.205) TYPICAL RECOMMENDED LAND PATTERN NOTES: 1. Dimensioning and tolerancing per ANSI Y14.5M-1982. 2. Package length does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 3. Package width does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 4. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 5. Terminal numbers are shown for reference only. 6. The lead width as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 7. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. 8. This outline conforms to JEDEC publication MS-012-AA ISSUE C. 18 FN7698.1 September 1, 2011