PHILIPS ISP1760BE

ISP1760
Hi-Speed Universal Serial Bus host controller for embedded
applications
Rev. 01 — 8 November 2004
Product data sheet
1. General description
The ISP1760 is a Hi-Speed Universal Serial Bus (USB) Host Controller with a generic
processor interface. It integrates one Enhanced Host Controller Interface (EHCI), one
Transaction Translator (TT) and three transceivers. The Host Controller portion of the
ISP1760 and the three transceivers comply to Universal Serial Bus Specification Rev. 2.0.
The EHCI portion of the ISP1760 is adapted from Enhanced Host Controller Interface
Specification for Universal Serial Bus Rev. 1.0.
The integrated high-performance Hi-Speed USB transceivers enable the ISP1760 to
handle all Hi-Speed USB transfer speed modes: high-speed (480 Mbit/s), full-speed
(12 Mbit/s) and low-speed (1.5 Mbit/s). The three downstream ports allow simultaneous
connection of three devices at different speeds (high-speed, full-speed and low-speed).
The generic processor interface allows the ISP1760 to be connected to various
processors as a memory-mapped resource. The ISP1760 is a slave host: it does not
require ‘bus-mastering’ capabilities of the host system bus. The interface is configurable,
ensuring compatibility with a variety of processors. Data transfer can be performed on
16 bits or 32 bits, using Programmed Input/Output (PIO) or Direct Memory Access (DMA)
with major control signals configurable as active LOW or active HIGH.
Integration of the TT allows connection to full-speed and low-speed devices, without the
need of integrating Open Host Controller Interface (OHCI) or Universal Host Controller
Interface (UHCI). Instead of dealing with two sets of software drivers—EHCI and OHCI or
UHCI—you need to deal with only one set—EHCI—that dramatically reduces software
complexity and IC cost.
2. Features
■ The Host Controller portion of the ISP1760 complies with Universal Serial Bus
Specification Rev. 2.0
■ The EHCI portion of the ISP1760 is adapted from Enhanced Host Controller Interface
Specification for Universal Serial Bus Rev. 1.0
■ Contains three integrated Hi-Speed transceivers that support the high-speed,
full-speed and low-speed modes
■ Integrates a TT for Original USB (full-speed and low-speed) device support
■ Up to 64-kbyte internal memory (8 k x 64 bits) accessible through a generic processor
interface; operation in multitasking environments is made possible by the
implementation of virtual segmentation mechanism with bank switching on task
request
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
■ Generic processor interface (nonmultiplexed and variable latency) with a configurable
32-bit or 16-bit external data bus; the processor interface can be defined as
variable-latency or SRAM type (memory mapping)
■ Slave DMA support for reducing the load of the host system CPU during the data
transfer to or from the memory
■ Integrated phase-locked loop (PLL) with a 12 MHz crystal or an external clock input
■ Integrated multiconfiguration FIFO
■ Optimized ‘msec-based’ or ‘multi-msec-based’ Philips Transfer Descriptor (PTD)
interrupt
■ Tolerant I/O for low voltage CPU interface (1.65 V to 3.6 V)
■ 3.3 V-to-5.0 V external power supply input
■ Integrated 5.0 V-to-1.8 V or 3.3 V-to-1.8 V voltage regulator (internal 1.8 V for
low-power core)
■ Internal power-on reset and low-voltage reset
■ Supports suspend and remote wake-up
■ Target current consumption:
◆ Normal operation; one port in high-speed active: ICC < 100 mA
◆ Suspend mode: Isusp < 150 µA at the room temperature
■ Built-in configurable overcurrent circuitry (digital or analog overcurrent protection)
■ Available in LQFP128 package.
3. Applications
The ISP1760 can be used to implement a Hi-Speed USB compliant Host Controller
connected to most of the CPUs present in the market today, having a generic processor
interface with demultiplexed address and data bus. This is because of the efficient
slave-type interface of the ISP1760.
The internal architecture of the ISP1760 is such that it can be used in a large spectrum of
applications requiring a high-performance internal Host Controller.
3.1 Examples of a multitude of possible applications
■
■
■
■
■
■
Set-top box: for connecting external high-performance mass storage devices
Mobile phone: for connecting various USB devices
Personal Digital Assistant (PDA): for connecting a large variety of USB devices
Printer: for connecting external memory card readers, allowing direct printing
Digital Still Camera (DSC): for printing to an external USB printer, for direct printing
Mass storage: for connecting external memory card readers or other mass storage
devices, for direct back-up.
The low power consumption and deep power management modes of the ISP1760
make it particularly suitable for use in portable devices.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
2 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
4. Ordering information
Table 1:
Ordering information
Type number Package
ISP1760BE
Name
Description
Version
LQFP128
plastic low profile quad flat package; 128 leads;
body 14 x 20 x 1.4 mm
SOT425-1
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
3 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
5. Block diagram
VCC(I/O)
10, 40, 48, 59, 67,
75, 83, 94, 104, 115
37 to 39, 41 to 43,
45 to 47, 49, 51,
52, 54, 56 to 58,
60 to 62, 64 to 66,
68 to 70, 72 to 74,
76 to 78, 80
DATA[15:0]/DATA[31:0]
GENERIC PROCESSOR BUS
82, 84, 86, 87,
89, 91 to 93,
95 to 98,
100 to 103, 105
A[17:1]
CS_N
106
RD_N
107
PLL
RISC PROCESSOR
16-bit
INTERNAL MEMORY
INTERFACE:
30 MHz
or
UP TO 64 KBYTES
60 MHz
32-bit
MEMORY
VIRTUAL SEGMENTATION
MANAGEMENT
FOR MULTITASKING SUPPORT
UNIT
+
GLOBAL CONTROL
INTERRUPT
AND POWER
CONTROL
MANAGEMENT
+
MEMORY
SLAVE DMA
ARBITER
CONTROLLER
AND FIFO
POWER-ON RESET
+
AND VBAT ON
HARDWARE
CONFIGURATION
REGISTERS
5 V-TO-1.8 V
VOLTAGE
EHCI AND
REGULATOR
OPERATIONAL
REGISTERS
TRANSACTION
17
112
DREQ 114
DACK
11
PTD AND PAYLOAD MEMORY:
WR_N 108
IRQ
ISP1760
116
TRANSLATOR
AND RAM
USB FULL-SPEED AND LOW SPEED DATA PATH
USB HIGH-SPEED DATA PATH
16 15
20 19 18 21 127
23 22
27 26
RESET_N
119
SUSPEND/
WAKEUP_N
110
VBAT_ON_N
6, 7
9
2
VREG(1V8)
VCC(5V0)
VREG(3V3)
REF5V
HI-SPEED
USB ATX3
HI-SPEED
USB ATX2
HI-SPEED
USB ATX1
CLKIN
5, 50,
85, 118
DIGITAL
AND ANALOG
OVERCURRENT
DETECTION
PORT ROUTING OR CONTROL LOGIC + HOST AND HUB PORT STATUS
XTAL2
13
122
5 V-TO-3.3 V
VOLTAGE
REGULATOR
PIE
XTAL1
12
25 28 128
30 29 34 33 32 35 1
4, 8, 14, 17, 24,
31, 36, 44, 53,
55, 63, 71, 79,
88, 90, 99, 109,
121, 123
004aaa435
RREF1
GND
DP1
RREF2
DM1
GND
OC1_N
PSW1_N
GND
DP2
GND
DM2
RREF3
OC2_N
DP3
GND
PSW2_N
GND
DM3
GND
OC3_N
PSW3_N
Fig 1. Block diagram.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
4 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
6. Pinning information
103
128
6.1 Pinning
102
1
ISP1760BE
64
65
39
38
004aaa505
Fig 2. Pin configuration (LQFP128).
6.2 Pin description
Table 2:
Pin description
Symbol [1]
Pin
Type [2] Description
OC3_N
1
AI
port 3 analog (5 V input) and digital overcurrent input; if not used,
connect to VCC(I/O) through a 10 kΩ resistor
REF5V
2
AI
5 V reference input for analog OC detector; connect a 100 nF
decoupling capacitor
TEST
3
-
connect to ground
GND
4
-
analog ground
VREG(1V8)
5
P
core power output (1.8 V); internal 1.8 V for the digital core; used for
decoupling; connect a 100 nF capacitor
VCC(5V0)
6
P
input to internal regulators (3.0 V to 5.5 V); connect a 100 nF
decoupling capacitor
VCC(5V0)
7
P
input to internal regulators (3.0 V to 5.5 V); connect a 100 nF
decoupling capacitor
GND
8
-
oscillator ground
VREG(3V3)
9
P
regulator output (3.3 V); for decoupling only; connect a 100 nF
capacitor and a 4.7 µF to 10 µF capacitor
VCC(I/O)
10
P
digital supply; 1.65 V to 3.6 V; connect a 100 nF decoupling
capacitor
XTAL1
11
AI
12 MHz crystal connection input; connect to ground if an external
clock is used; see Table 84
XTAL2
12
AO
12 MHz crystal connection output
CLKIN
13
I
12 MHz oscillator or clock input; connect to VCC(I/O) when not in use
3.3 V tolerant
GND
14
-
digital ground
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
5 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 2:
Pin description…continued
Symbol [1]
Pin
Type [2] Description
GND
15
-
RREF1 ground
RREF1
16
AI
reference resistor connection; connect a 12 kΩ ± 1 % resistor
between this pin and the RREF1 ground
GND
17
-
analog ground for port 1
DM1
18
AI/O
downstream data minus port 1
GND
19
-
analog ground
DP1
20
AI/O
downstream data plus port 1
PSW1_N
21
OD
power switch port 1, active LOW
output pad, push-pull open-drain, 8 mA output drive, 5 V tolerant
GND
22
-
RREF2 ground
RREF2
23
AI
reference resistor connection; connect a 12 kΩ ± 1 % resistor
between this pin and the RREF2 ground
GND
24
-
analog ground for port 2
DM2
25
AI/O
downstream data minus port 2
GND
26
-
analog ground
DP2
27
AI/O
downstream data plus port 2
PSW2_N
28
OD
power switch port 2, active LOW
GND
29
-
RREF3 ground
RREF3
30
AI
reference resistor connection; connect a 12 kΩ ± 1 % resistor
between this pin and the RREF3 ground
GND
31
-
analog ground for port 3
DM3
32
AI/O
downstream data minus port 3
GND
33
-
analog ground
DP3
34
AI/O
downstream data plus port 3
PSW3_N
35
OD
power switch port 3, active LOW
output pad, push-pull open-drain, 8 mA output drive, 5 V tolerant
output pad, push-pull open-drain, 8 mA output drive, 5 V tolerant
GND
36
-
digital ground
DATA0
37
I/O
data bit 0 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
DATA1
38
I/O
data bit 1 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
DATA2
39
I/O
data bit 2 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
VCC(I/O)
40
P
digital supply; 1.65 V to 3.6 V; connect a 100 nF decoupling
capacitor
DATA3
41
I/O
data bit 3 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
6 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 2:
Pin description…continued
Symbol [1]
Pin
Type [2] Description
DATA4
42
I/O
data bit 4 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
DATA5
43
I/O
data bit 5 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
GND
44
-
digital ground
DATA6
45
I/O
data bit 6 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
DATA7
46
I/O
data bit 7 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
DATA8
47
I/O
data bit 8 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
VCC(I/O)
48
P
digital supply; 1.65 V to 3.6 V; connect a 100 nF decoupling
capacitor
DATA9
49
I/O
data bit 9 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
VREG(1V8)
50
P
core power output (1.8 V); internal 1.8 V for the digital core; used for
decoupling; connect a 100 nF capacitor
DATA10
51
I/O
data bit 10 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
DATA11
52
I/O
data bit 11 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
GND
53
-
core ground
DATA12
54
I/O
data bit 12 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
GND
55
-
digital ground
DATA13
56
I/O
data bit 13 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
DATA14
57
I/O
data bit 14 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
DATA15
58
I/O
data bit 15 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
VCC(I/O)
59
P
digital supply; 1.65 V to 3.6 V; connect a 100 nF decoupling
capacitor
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
7 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 2:
Pin description…continued
Symbol [1]
Pin
Type [2] Description
DATA16
60
I/O
data bit 16 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
DATA17
61
I/O
data bit 17 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
DATA18
62
I/O
data bit 18 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
GND
63
-
digital ground
DATA19
64
I/O
data bit 19 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
DATA20
65
I/O
data bit 20 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
DATA21
66
I/O
data bit 21 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
VCC(I/O)
67
P
digital supply; 1.65 V to 3.6 V; connect a 100 nF decoupling
capacitor
DATA22
68
I/O
data bit 22 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
DATA23
69
I/O
data bit 23 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
DATA24
70
I/O
data bit 24 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
GND
71
-
digital ground
DATA25
72
I/O
data bit 25 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
DATA26
73
I/O
data bit 26 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
DATA27
74
I/O
data bit 27 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
VCC(I/O)
75
P
digital supply; 1.65 V to 3.6 V; connect a 100 nF decoupling
capacitor
DATA28
76
I/O
data bit 28 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
8 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 2:
Pin description…continued
Symbol [1]
Pin
Type [2] Description
DATA29
77
I/O
data bit 29 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
DATA30
78
I/O
data bit 30 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
GND
79
-
digital ground
DATA31
80
I/O
data bit 31 input and output
bidirectional pad, push-pull input, three-state output, 4 mA output
drive, 3.3 V tolerant
TEST
81
-
connect to ground
A1
82
I
address pin 1
input, 3.3 V tolerant
VCC(I/O)
83
P
digital supply; 1.65 V to 3.6 V; connect a 100 nF decoupling
capacitor
A2
84
I
address pin 2
input, 3.3 V tolerant
VREG(1V8)
85
P
core power output (1.8 V); internal 1.8 V for the digital core; used for
decoupling; connect a 100 nF capacitor and a 4.7 µF to 10 µF
capacitor
A3
86
I
address pin 3
A4
87
I
address pin 4
input, 3.3 V tolerant
input, 3.3 V tolerant
GND
88
-
core ground
A5
89
I
address pin 5
input, 3.3 V tolerant
GND
90
-
digital ground
A6
91
I
address pin 6
input, 3.3 V tolerant
A7
92
I
address pin 7
input, 3.3 V tolerant
A8
93
I
address pin 8
input, 3.3 V tolerant
VCC(I/O)
94
P
digital supply; 1.65 V to 3.6 V; connect a 100 nF decoupling
capacitor
A9
95
I
address pin 9
input, 3.3 V tolerant
A10
96
I
address pin 10
input, 3.3 V tolerant
A11
97
I
address pin 11
A12
98
I
address pin 12
input, 3.3 V tolerant
input, 3.3 V tolerant
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
9 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 2:
Pin description…continued
Symbol [1]
Pin
Type [2] Description
GND
99
-
digital ground
A13
100
I
address pin 13
A14
101
I
address pin 14
input, 3.3 V tolerant
input, 3.3 V tolerant
A15
102
I
address pin 15
input, 3.3 V tolerant
A16
103
I
address pin 16
input, 3.3 V tolerant
VCC(I/O)
104
P
digital voltage; 1.65 V to 3.6 V; connect a 100 nF decoupling
capacitor
A17
105
I
address pin 17
input, 3.3 V tolerant
CS_N
106
I
chip select signal that indicates the area being accessed; active
LOW
input, 3.3 V tolerant
RD_N
107
I
read enable; active LOW
input, 3.3 V tolerant
WR_N
108
I
write enable; active LOW
GND
109
-
digital ground
VBAT_ON_N
110
OD
to indicate the presence of a minimum 3.3 V on pins 6 and 7
(open-drain); connect to VCC(I/O) through a 10 kΩ pull-up resistor
input, 3.3 V tolerant
output pad, push-pull open-drain, 8 mA output drive, 5 V tolerant
n.c.
111
-
not connected
IRQ
112
O
Host Controller interrupt signal
output pad, 4 mA drive, 3.3 V tolerant
n.c.
113
-
not connected
DREQ
114
O
DMAC request for the Host Controller
output pad, 4 mA drive, 3.3 V tolerant
VCC(I/O)
115
P
digital voltage; 1.65 V to 3.6 V; connect a 100 nF decoupling
capacitor
DACK
116
I
Host Controller DMA request acknowledgment; when not in use,
connect to VCC(I/O) through a 10 kΩ pull-up resistor
input, 3.3 V tolerant
TEST
117
-
connect to ground
VREG(1V8)
118
P
core power output (1.8 V); internal 1.8 V for the digital core; used for
decoupling; connect a 100 nF capacitor
I/OD
Host Controller suspend and wake-up; three-state suspend output
(active LOW) and wake-up input circuits are connected together
SUSPEND/ 119
WAKEUP_
N
•
HIGH = output is three-state; ISP1760 is in suspend mode;
connect to VCC(I/O) through an external 10 kΩ pull-up resistor
•
LOW = output is LOW; ISP1760 is not in suspend mode.
output pad, open-drain, 4 mA output drive, 3.3 V tolerant
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
10 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 2:
Pin description…continued
Symbol [1]
Pin
Type [2] Description
TEST
120
-
pull up to VCC(I/O)
GND
121
-
core ground
RESET_N
122
I
external power-up reset; active LOW
input, 3.3 V tolerant
GND
123
-
analog ground
TEST
124
-
connect a 220 nF capacitor between this pin and pin 125
TEST
125
-
connect a 220 nF capacitor between this pin and pin 124
TEST
126
-
connect to 3.3 V
OC1_N
127
AI
port 1 analog (5 V input) and digital overcurrent input; if not used,
connect to VCC(I/O) through a 10 kΩ resistor
OC2_N
128
AI
port 2 analog (5 V input) and digital overcurrent input; if not used,
connect to VCC(I/O) through a 10 kΩ resistor
[1]
Symbol names ending with underscore N (for example, NAME_N) represent active LOW signals.
[2]
I = input only; O = output only; I/O = digital input/output; OD = open-drain output; AI/O = analog
input/output; AI = analog input; P = power.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
11 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
7. Functional description
7.1 ISP1760 internal architecture: Advanced Philips Slave Host Controller
and hub
The EHCI block and the Hi-Speed USB hub block are the main components of the
Advanced Philips Slave Host Controller.
The EHCI is the latest generation design, with improved data bandwidth. The EHCI in the
ISP1760 is adapted from Enhanced Host Controller Interface Specification for Universal
Serial Bus Rev. 1.0.
The internal Hi-Speed USB hub block replaces the companion Host Controller block used
in the original PCI Hi-Speed USB Host Controllers to handle the full-speed and low-speed
modes. The hardware architecture in the ISP1760 is simplified to help reduce cost and
development time, by eliminating the additional work involved in implementing the OHCI
software required to support the full-speed and low-speed modes.
Figure 3 shows the internal architecture of the ISP1760. The ISP1760 implements the
EHCI that has an internal port—the Root Hub port (not available externally)—on which the
internal hub is connected. The three external ports are always routed to the internal hub.
The internal hub is a Hi-Speed USB (USB 2.0) hub including the TT.
Remark: The root hub must be enabled and the internal hub must be enumerated.
Enumerate the internal hub as if it is externally connected. For details, refer to ISP176x
Linux Programming Guide (AN10042).
At the Host Controller reset and initialization, the internal Root Hub port will be polled until
a new connection is detected, showing the connection of the internal hub.
The internal Hi-Speed USB hub is enumerated using a sequence similar to a standard
Hi-Speed USB hub enumeration sequence, and the polling on the Root Hub is stopped
because the internal Hi-Speed USB hub will never be disconnected. When enumerated,
the internal hub will report the three externally available ports.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
12 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
EHCI
ROOT HUB
PORTSC1
ENUMERATION
AND POLLING USING
ACTUAL PTDs
INTERNAL HUB (TT)
PORT1
PORT2
PORT3
EXTERNAL
PORTS
004aaa513
Fig 3. Internal hub.
7.2 Host Controller buffer memory block
7.2.1 General considerations
The internal addressable Host Controller buffer memory is 63 kbytes. The 63-kbyte
effective memory size is the result of subtracting the size of registers (1 kbyte) from the
total addressable memory space defined in the ISP1760 (64 kbytes). This is the optimized
value for achieving the highest performance with a minimal cost.
The ISP1760 is a slave Host Controller. This means that it does not need access to the
local bus of the system to transfer data from the memory of the system to the ISP1760
internal memory, unlike the case of the original PCI Hi-Speed USB Host Controllers.
Therefore, correct data must be transferred to both the Philips Transfer Descriptor (PTD)
area and the payload area by Parallel I/O (PIO) (CPU access) or programmed DMA.
The ‘slave-host’ architecture ensures better compatibility with most of the processors
present in the market today because not all processors allow a ‘bus-master’ on the local
bus. It also allows better load balancing of the processor’s local bus because only the
internal bus arbiter of the processor controls the transfer of data dedicated to USB. This
prevents the local bus from being busy when other more important transfers may be in the
queue; and therefore achieving a ‘linear’ system data flow that has less impact on other
processes running at the same time.
The considerations mentioned are also the main reason for implementing the prefetching
technique, instead of using a READY signal. The resulting architecture avoids ‘freezing’ of
the local bus (by asserting READY), enhancing the ISP1760 memory access time, and
avoiding introduction of programmed additional wait states. For details, see Section 7.3
and Section 8.3.8.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
13 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
The total amount of memory allocated to the payload determines the maximum transfer
size specified by a PTD—a larger internal memory size results in less CPU interruption for
transfer programming. This means less time spent in context switching, resulting in better
CPU usage.
A larger buffer also implies a larger amount of data can be transferred. The transfer,
however, can be done over a longer period of time, to maintain the overall system
performance. Each transfer of the USB data on the USB bus can span for up to a few
milliseconds before requiring further CPU intervention for data movement.
The internal architecture of the ISP1760 allows a flexible definition of the memory buffer
for optimization of the data transfer on the CPU extension bus and the USB. It is possible
to implement various data transfer schemes, depending on the number and type of USB
devices present (for example: push-pull—data can be written to half of the memory while
data in the other half is being accessed by the Host Controller and sent on the USB bus).
This is useful especially when a high-bandwidth ‘continuous or periodic’ data flow is
required.
Through an analysis of the hardware and software environment regarding the usual data
flow and performance requirements of most embedded systems, Philips has determined
the optimal size for the internal buffer as approximately 64 kbytes.
7.2.2 Structure of the ISP1760 Host Controller memory
The 63-kbyte internal memory consists of the PTD area and the payload area.
Both the PTD and payload memory zones are divided into three dedicated areas for each
main type of USB transfer: isochronous (ISO), interrupt (INT) and Acknowledged Transfer
List (ATL). As shown in Table 3, the PTD areas for ISO, INT and ATL are grouped at the
beginning of the memory, occupying the address range 0400h to 0FFFh, following the
address space of the registers. The payload or data area occupies the next memory
address range 1000h to FFFFh, meaning that 60 kbytes of memory are allocated for the
payload data.
A maximum of 32 PTD areas and their allocated payload areas can be defined for each
type of transfer. The structure of a PTD is similar for every transfer type and consists of
eight Double Words (DWs) that must be correctly programmed for a correct USB data
transfer. The reserved bits of a PTD must be set to logic 0. A detailed description of the
PTD structure can be found in Section 9.
The transfer size specified by the PTD determines the contiguous USB data transfer that
can be performed without any CPU intervention. The respective payload memory area
must be equal to the transfer size defined. The maximum transfer size is flexible and can
be optimized, depending on the number and nature of USB devices or PTDs defined and
their respective MaxPacketSize.
The CPU will program the DMA to transfer the necessary data in the payload memory.
The next CPU intervention will be required only when the current transfer is completed
and DMA programming is necessary to transfer the next data payload. This is normally
signaled by the IRQ that is generated by the ISP1760 on completing the current PTD,
meaning all the data in the payload area was sent on the USB bus. The external IRQ
signal is asserted according to the settings in the IRQ Mask OR or IRQ Mask AND
registers, see Section 8.4.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
14 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
The RAM is structured in blocks of PTDs and payloads so that while the USB is executing
on an active transfer-based PTD, the processor can simultaneously fill up another block
area in the RAM. A PTD and its payload can then be updated on-the-fly without stopping
or delaying any other USB transaction or corrupting the RAM data.
Some of the design features are:
• The address range of the internal RAM buffer is from 0400h to FFFFh.
• The internal memory contains isochronous, interrupt and asynchronous PTDs, and
respective defined payloads.
• All accesses to the internal memory are double-word aligned.
• Internal memory address range calculation:
Memory address = (CPU address – 0400h) (shift right >> 3). Base address is 0400h.
Table 3:
Memory address
Memory map
CPU address
Memory address
ISO
0400h to 07FFh
0000h to 007Fh
INT
0800h to 0BFFh
0080h to 00FFh
ATL
0C00h to 0FFFh
0100h to 017Fh
Payload
1000h to FFFFh
0180h to 1FFFh
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
15 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
PTD1
63 kbytes
PTD2
..
ISOCHRONOUS
PTD32
PTD1
PTD2
..
INTERRUPT
PTD32
PTD1
REGISTERS
PTD2
..
ASYNC
PTD32
PAYLOAD
USB HIGH-SPEED
HOST AND
TRANSACTION
TRANSLATOR
(FULL-SPEED
AND LOW-SPEED)
........
USB BUS
D[15:0]/D[31:0]
PAYLOAD
PAYLOAD
address
data (64 bits)
240 MB/s
MEMORY MAPPED
INPUT/OUTPUT,
MEMORY
MANAGEMENT
UNIT,
SLAVE DMA
CONTROLLER
AND
INTERRUPT
CONTROL
A[17:1]
CS_N
RD_N
MICROPROCESSOR
WR_N
IRQ
DREQ
ARBITER
control signals
DACK
004aaa436
Fig 4. Memory segmentation and access block diagram.
Both the CPU interface logic and the USB Host Controller require access to the internal
ISP1760 RAM at the same time. The internal arbiter controls these accesses to the
internal memory, organized internally on a 64-bit data bus width, allowing a maximum
bandwidth of 240 MB/s. This bandwidth avoids any bottleneck on accesses both from the
CPU interface and the internal USB Host Controller.
7.3 Accessing the ISP1760 Host Controller memory: PIO and DMA
The CPU interface of the ISP1760 can be configured for a 16-bit or 32-bit data bus width.
When the ISP1760 is configured for a 16-bit data bus width, the upper unused 16 data
lines must be pulled up to VCC(I/O). This can be achieved by connecting DATA[31:16] lines
together to a single 10 kΩ pull-up resistor. The 16-bit or 32-bit data bus width
configuration is done by programming bit 8 of the HW Mode Control register. This will
determine the register and memory access types in both PIO and DMA modes to all
internal blocks: Host Controller, Peripheral Controller and OTG Controller. All accesses
must be word-aligned for 16-bit mode and double-word aligned for 32-bit mode, where
one word = 16 bits. When accessing the Host Controller registers in 16-bit mode, the
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
16 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
register access must always be completed using two subsequent accesses. In the case of
a DMA transfer, the 16-bit or 32-bit data bus width configuration will determine the number
of bursts that will complete a certain transfer length.
In PIO mode, CS_N, WR_N and RD_N are used to access registers and memory. In DMA
mode, the data validation is performed by DACK—instead of CS_N—together with the
WR_N and RD_N signals. The DREQ signal will always be asserted as soon as the
ISP1760 DMA is enabled, as described in the following section.
7.3.1 PIO mode access—memory read cycle
The following method has been implemented to reduce the read access timing in the case
of a memory read:
• The Memory register contains the starting address and the bank selection to read
from the memory. Before every new read cycle of the same or different banks, an
appropriate value is written to this register.
• Once a value is written to this register, the address is stored in the FIFO of that bank
and is then used to prefetch data for the memory read of that bank.
For every subsequent read operation executed at a contiguous address, the address
pointer corresponding to that bank is automatically incremented to prefetch the next
data to be sent to the CPU.
Memory read accesses for multiple banks can be interleaved. In this case, the FIFO
block handles the MUXing of appropriate data to the CPU.
• The address written to the Memory register is incremented and used to successively
prefetch data from the memory irrespective of the value on the address bus for each
bank, until a new value for a bank is written to the Memory register.
For example, consider the following sequence of operations:
– Write the starting (read) address 4000h and bank1 = 01 to the Memory register.
When RD_N is asserted for three cycles with A[17:16] = 01, the returned data
corresponds to addresses 4000h, 4004h and 4008h.
Remark: Once 4000h is written to the Memory register for bank1, the bank select
value determines the successive incremental addresses used to fetch the data.
That is, the fetching of data is independent of the address on A[15:0] lines.
– Write the starting (read) address 4100h and bank2 = 10 to the Memory register.
When RD_N is asserted for four cycles with A[17:16] = 10, the returned data
corresponds to addresses 4100h, 4104h, 4108h and 410Ch.
Consequently, the RD_N assertion with A[17:16] = 01 will return data from 400Ch
because the bank1 read stopped there in the previous cycle. Also, RD_N
assertions with A[17:16] = 010 will now return data from 4110h because the bank2
read stopped there in the previous cycle.
7.3.2 PIO mode access—memory write cycle
The PIO memory write access is similar to a normal memory access. It is not necessary
to set the prefetching address before a write cycle to the memory.
The ISP1760 internal write address will not be automatically incremented during
consecutive write accesses, unlike in a series of ISP1760 memory read cycles. The
memory write address must be incremented before every access.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
17 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
7.3.3 PIO mode access—register read cycle
The PIO register read access is similar to a general register access. It is not necessary to
set a prefetching address before a register read.
The ISP1760 register read address will not be automatically incremented during
consecutive read accesses, unlike in a series of ISP1760 memory read cycles. The
ISP1760 register read address must be correctly specified before every access.
7.3.4 PIO mode access—register write cycle
The PIO register write access is similar to a general register access. It is not necessary to
set a prefetching address before a register write.
The ISP1760 register write address will not be automatically incremented during
consecutive write accesses, unlike in a series of ISP1760 memory read cycles. The
ISP1760 register write address must be correctly specified before every access.
7.3.5 DMA—read and write operations
The internal ISP1760 Host Controller DMA is a slave DMA. The host system processor or
DMA must ensure the data transfer to or from the ISP1760 memory.
The ISP1760 DMA supports a DMA burst length of 1, 4, 8 and 16 cycles for both the 16-bit
and 32-bit data bus width. DREQ will be asserted at the beginning of the first burst of a
DMA transfer and will be deasserted on the last cycle (RD_N or WR_N active pulse) of
that burst. It will be reasserted shortly after the DACK deassertion, as long as the DMA
transfer counter was not reached. DREQ will be deasserted on the last cycle when the
DMA transfer counter is reached and will not reasserted until the DMA reprogramming is
performed. Both the DREQ and DACK signals are programmable as active LOW or active
HIGH, according to the system requirements.
The DMA start address must be initialized in the respective register, and the subsequent
transfers will automatically increment the internal ISP1760 memory address. A register or
memory access or access to other system memory can occur in between DMA bursts,
whenever the bus is released because DACK is deasserted, without affecting the DMA
transfer counter or the current address.
Any memory area can be accessed by the system’s DMA at any starting address because
there are no predefined memory blocks. The DMA transfer must start on a word or Double
Word address, depending on whether the data bus width is set to 16 bit or 32 bit. DMA is
the most efficient method to initialize the payload area, to reduce the CPU usage and
overall system loading.
The ISP1760 does not implement EOT to signal the end of a DMA transfer. If
programmed, an interrupt may be generated by the ISP1760 at the end of the DMA
transfer.
The slave DMA of the ISP1760 will issue a DREQ to the DMA controller of the system to
indicate that it is programmed for transfer and data is ready. The system DMA controller
may also start a transfer without the need of the DREQ, if the ISP1760 memory is
available for the data transfer and the ISP1760 DMA programming is completed.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
18 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
It is also possible that the system’s DMA will perform a memory-to-memory type of
transfer between the system memory and the ISP1760 memory. The ISP1760 will be
accessed in the PIO mode. Consequently, memory read operations must be preceded by
initializing the Memory register (address 033Ch), as described in Section 7.3.1. No IRQ
will be generated by the ISP1760 on completing the DMA transfer but an internal
processor interrupt may be generated to signal that the DMA transfer is completed. This is
mainly useful in implementing the double-buffering scheme for data transfer to optimize
the USB bandwidth.
The ISP1760 DMA programming involves:
• Set the active levels of signals DREQ and DACK in the HW Mode Control register.
• The DMA Start Address register contains the first memory address at which the data
transfer will start. It must be word-aligned in the 16-bit data bus mode and double
word aligned in the 32-bit data bus mode.
• The programming of the DMA Configuration register specifies:
– The type of transfer that will be performed: read or write
– The burst size—expressed in bytes—is specified, regardless of the data bus width.
For the same burst size, a double number of cycles will be generated in the 16-bit
mode data bus width as compared to the 32-bit mode.
– The transfer length—expressed in number of bytes—defines the number of bursts.
The DREQ will be deasserted and asserted to generate the next burst, as long as
there are bytes to be transferred. At the end of a transfer, the DREQ will be
deasserted and an IRQ can be generated if DMAEOTINT (bit 3 in the Interrupt
register) is set. The maximum DMA transfer size is equal to the maximum memory
size. The transfer size can be an odd or even number of bytes, as required. If the
transfer size is an odd number of bytes, the number of bytes transferred by the
system’s DMA is equal to the next multiple of two for the 16-bit data bus width or
four for the 32-bit data bus width. For a write operation, however, only the specified
odd number of bytes in the ISP1760 memory will be affected.
– Enable ENABLE_DMA (bit 1) of the DMA Configuration register to determine the
assertion of DREQ immediately after setting the bit.
After programming the preceding parameters, the system’s DMA may be enabled (waiting
for the DREQ to start the transfer or immediate transfer may be started).
The programming of the system’s DMA must match the ISP1760 DMA parameters
programmed above. Only one DMA transfer may take place at a time. A PIO mode data
transfer may occur simultaneously with a DMA data transfer, in the same or a different
memory area.
7.4 Interrupts
The ISP1760 will assert an IRQ according to the source or event in the Interrupt register.
The main steps to enable the IRQ assertion are:
1. Set GLOBAL_INTR_EN (bit 0) in the HW Mode Control register.
2. Define the IRQ active as level or edge in INTR_LEVEL (bit 1) of the HW Mode Control
register.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
19 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
3. Define the IRQ polarity as active LOW or active HIGH in INTR_POL (bit 2) of the HW
Mode Control register. These settings must match the IRQ settings of the host
processor.
By default, interrupt is level-triggered and active LOW.
4. Program the individual interrupt enable bits in the Interrupt Enable register. The
software will need to clear the interrupt status bits in the Interrupt register before
enabling individual interrupt enable bits.
Additional IRQ characteristics can be adjusted in the Edge Interrupt Count register, as
necessary, applicable only when IRQ is set to be edge-active (a pulse of a defined width is
generated every time IRQ is active).
Bits 15 to 0 of the Edge Interrupt Count register define the IRQ pulse width. The maximum
pulse width that can be programmed is FFFFh, corresponding to a 1 ms pulse width. This
setting is necessary for certain processors that may require a different minimum IRQ
pulse width than the default value. The default IRQ pulse width set at power on is
approximately 500 ns.
Bits 31 to 24 of the Edge Interrupt Count register define the minimum interval between
two interrupts to avoid frequent interrupts to the CPU. The default value of 00h attributed
to these bits determines the normal IRQ generation, without any delay. When a delay is
programmed and the IRQ becomes active after the respective delay, several IRQ events
may have already occurred.
All the interrupt events are represented by the respective bits allocated in the Interrupt
register. There is no mechanism to show the order or the moment of occurrence of an
interrupt.
The asserted bits in the Interrupt register can be cleared by writing back the same value to
the Interrupt register. This means that writing logic 1 to each of the set bits will reset the
corresponding bits to the initial inactive state.
The IRQ generation rules that apply according to the preceding settings are:
• If an event of interrupt occurs but the respective bit in the Interrupt Enable register is
not set, then the respective Interrupt register bit is set but the interrupt signal is not
asserted.
An interrupt will be generated when interrupt is enabled and the respective bit in the
Interrupt Enable register is set.
• For a level trigger, an interrupt signal remains asserted until the processor clears the
Interrupt register by writing logic 1 to clear the Interrupt register bits that are set.
• If an interrupt is made edge-sensitive and is asserted, writing to clear the Interrupt
register will not have any effect because the interrupt will be asserted for a prescribed
amount of clock cycles.
• The clock stopping mechanism does not affect the generation of an interrupt. This is
useful during the suspend and resume cycles, when an interrupt is generated to
signal a wake-up event.
The IRQ generation can also be conditioned by programming the IRQ Mask OR and
IRQ Mask AND registers. Setting some of the bits in these registers to logic 1 will
determine the IRQ generation only when the respective AND or OR conditions of
completing the respective PTDs is met.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
20 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
With the help of the IRQ Mask AND and IRQ Mask OR registers for each type of
transfer—ISO, INT and bulk—software can determine which PTDs get priority and an
interrupt will be generated when the AND or OR conditions are met. The PTDs that are
set will wait until the respective bits of the remaining PTDs are set and then all PTDs
generate an interrupt request to the CPU together.
The registers definition shows that the AND or OR conditions are applicable to the same
category of PTDs—ISO, INT, ATL.
When an IRQ is generated, the PTD Done Map registers and the respective V bits will
show which PTDs were completed.
The rules that apply to the IRQ Mask AND or IRQ Mask OR settings are:
• The OR mask has a higher priority over the AND mask. An IRQ is generated if bit n of
the done map is set and the corresponding bit n of the OR Mask register is set.
• If the OR mask for any done bit is not set, then the AND mask comes into picture. An
IRQ is generated if all the corresponding done bits of the AND Mask register are set.
For example: If bits 2, 4 and 10 are set in the AND Mask register, an IRQ is generated
only if bits 2, 4, 10 of the done map are set.
• If using the IRQ interval setting for the bulk PTD, an interrupt will only occur at the
regular time interval as programmed in the ATL Done Timeout register. Even if an
interrupt event occurs before the timeout of the register, no IRQ will be generated until
the time is up.
For an example on using the IRQ Mask AND or IRQ Mask OR registers without the ATL
Done Timeout register, see Table 4.
The AND function: Activate the IRQ only if PTDs 1, 2 and 4 are done.
The OR function: If any of the PTDs 7, 8 or 9 are done, an IRQ for each of the PTD will be
raised.
Table 4:
Using the IRQ Mask AND or IRQ Mask OR registers
PTD
AND register
OR register
Time
PTD done
IRQ
1
1
0
1 ms
1
-
2
1
0
-
1
-
3
0
0
-
-
-
4
1
0
3 ms
1
active because of AND
5
0
0
-
-
-
6
0
0
-
-
-
7
0
1
5 ms
1
active because of OR
8
0
1
6 ms
1
active because of OR
9
0
1
7 ms
1
active because of OR
7.5 Phase-Locked Loop (PLL) clock multiplier
The internal PLL requires a 12 MHz input, which can be a 12 MHz crystal or a 12 MHz
clock already existing in the system with a precision better than 50 ppm. This allows the
use of a low-cost 12 MHz crystal that also minimizes Electro-Magnetic Interference (EMI).
When an external crystal is used, make sure the CLKIN pin is connected to VCC(I/O).
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
21 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
The PLL block generates all the main internal clocks required for normal functionality of
various blocks: 30 MHz, 48 MHz and 60 MHz.
No external components are required for the PLL operation.
7.6 Power management
The ISP1760 implements a flexible power management scheme, allowing various power
saving stages.
The usual powering scheme implies programming EHCI registers and the internal
Hi-Speed USB (USB 2.0) hub in the same way it is done in the case of a PCI Hi-Speed
USB Host Controller with a Hi-Speed USB hub attached.
When the ISP1760 is in suspend mode, the main internal clocks will be stopped to ensure
minimum power consumption. An internal LazyClock of 100 kHz ± 40 % will continue
running. This allows initiating a resume on one of the following events:
• External USB device connect or disconnect
• Assertion of the CS_N signal because of any access to the ISP1760
• Driving the SUSPEND/WAKEUP_N pin to a LOW level.
The SUSPEND/WAKEUP_N pin is a bidirectional pin. This pin should be connected to
one of the GPIO pins of a processor.
The awake state can be verified by reading the LOW level of this pin. If the level is HIGH,
it means that the ISP1760 is in the suspend state.
The SUSPEND/WAKEUP_N pin requires a pull-up because in the ISP1760 suspended
state the pin becomes three-state and can be pulled down, driving it externally by
switching the processor’s GPIO line to the output mode to generate the ISP1760 wake-up.
The SUSPEND/WAKEUP_N pin is a three-state output. It is also an input to the internal
wake-up logic.
When in suspend mode, the ISP1760 internal wake-up circuitry will sense the status of
the SUSPEND/WAKEUP_N pin:
• If it remains pulled-up, no wake-up is generated because a HIGH is sensed by the
internal wake-up circuit.
• If the pin is externally pulled LOW (for example, by the GPIO line or just as a test by
jumper), the input to the wake-up circuitry becomes LOW and the wake-up is
internally initiated.
The resume state has a clock-off count timer defined by bits 31 to 16 of the Power Down
Control register. The default value of this timer is 10 ms, meaning that the resume state
will be maintained for 10 ms. If during this time, the RUN/STOP bit in the USBCMD
register is set to logic 1, the Host Controller will go into a permanent resume—the normal
functional state. If the RUN/STOP bit is not set during the time determined by the clock-off
count, the ISP1760 will switch back to suspend mode after the specified time. The
maximum delay that can be programmed in the clock-off count field is approximately
500 ms.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
22 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Additionally, the Power Down Control register allows the ISP1760 internal blocks to be
disabled for lower power consumption as defined in Table 5.
The lowest suspend current that can be achieved is approximately 100 µA at room
temperature. The suspend current will increase with the increase in temperature, with
approximately 300 µA at 40 °C and up to a typical 1 mA at 85 °C. The system is not in
suspend mode when its temperature increases above 40 °C. Therefore, even a 1 mA
current consumption by the ISP1760 (in suspend mode) can be considered negligible. In
normal environmental conditions, when the system is in suspend mode, the maximum
ISP1760 temperature will be approximately 40 °C (determined by the ambient
temperature) so the ISP1760 maximum suspend current will be below 300 µA. An
alternative solution to achieve a very low suspend current is to completely switch off the
VCC(5V0) power input by using an external PMOS transistor, controlled by one of the GPIO
pins of the processor. This is possible because the ISP1760 can be used in the hybrid
mode, which allows only the VCC(I/O) powered on to avoid loading of the system bus.
The time from wake-up to suspend will be approximately 100 ms when the ISP1760
power is always on.
It is necessary to wait for the CLK_RDY interrupt assertion before programming the
ISP1760 because internal clocks are stopped during deep-sleep suspend and restarted
after the first wake-up event. The occurrence of the CLK_RDY interrupt means that the
internal clocks are running and the normal functionality is achieved.
It is estimated that the CLK_RDY interrupt will be generated less than 100 µs after the
wake-up event, if the power to the ISP1760 was on during suspend.
If the ISP1760 is used in the hybrid mode and VCC(5V0) is off during suspend, a 2 ms reset
pulse is required when the power is switched back to on, before starting to program the
resume state. This will ensure that the internal clocks are running and all logics reach a
stable initial state.
7.7 Overcurrent detection
The ISP1760 can implement a digital or analog overcurrent detection scheme. Bit 15 of
the HW Mode Control register can be programmed to select the analog or digital
overcurrent detection. An analog overcurrent detection circuit is integrated on-chip. The
main features of this circuit are self reporting, automatic resetting, low-trip time and low
cost. This circuit offers an easy solution at no extra hardware cost on the board. The port
power will be automatically disabled by the ISP1760 on an overcurrent event occurrence,
by deasserting the PSWn_N signal without any software intervention.
When using the integrated analog overcurrent detection, the range of the overcurrent
detection voltage for the ISP1760 is 45 mV to 100 mV. Calculation of the external
components should be based on the 45 mV value, with the actual overcurrent detection
threshold usually positioned in the middle of the interval.
For an overcurrent limit of 500 mA per port, a PMOS with RDSON of approximately 100 mΩ
is required. If a PMOS with a lower RDSON is used, analog overcurrent detection can be
adjusted using a series resistor; see Figure 5.
∆VPMOS = ∆VTRIP = ∆VTRIP(intrinsic) − (IOC(nom) × Rtd), where:
∆VPMOS = voltage drop on PMOS
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
23 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
IOC(nom) = 1 µA.
5V
IOC
Rtd(1)
PSWn_N
REF5V
OCn_N
ISP1760
004aaa662
(1) Rtd is optional.
Fig 5. Adjusting analog overcurrent detection limit (optional).
The digital overcurrent scheme requires using an external power switch with integrated
overcurrent detection, such as: LM3526, MIC2526 (2 ports) or LM3544 (4 ports). These
devices are controlled by PSWn_N signals corresponding to each port. In the case of
overcurrent occurrence, these devices will assert OCn_N signals. On OCn_N assertion,
the ISP1760 cuts off the port power by deasserting PSWn_N. The external integrated
power switch will also automatically cut-off the port power in the case of an overcurrent
event, by implementing thermal shutdown. An internal delay filter of 1 ms to 3 ms will
prevent false overcurrent reporting because of in-rush currents when plugging a USB
device.
7.8 Power supply
Figure 6 shows the ISP1760 power supply connection.
ISP1760
6, 7
VCC(5V0)
3.3 V to 5 V
100 nF
10, 40, 48,
59, 67, 75,
83, 94,
104, 115
VCC(I/O)
1.65 V to 3.6 V
100 nF
VREG(1V8)
85
100 nF
10 µF
VREG(1V8)
5, 50, 118
100 nF
VREG(3V3)
9
10 µF
100 nF
004aaa533
Fig 6. ISP1760 power supply connection.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
24 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Figure 7 shows the most commonly used power supply connection.
ISP1760
6, 7, 10,
40, 48, 59,
67, 75, 83,
94, 104, 115
VCC(5V0), VCC(I/O)
3.3 V
100 nF
VREG(1V8)
85
100 nF
10 µF
VREG(1V8)
5, 50, 118
100 nF
VREG(3V3)
9
100 nF
10 µF
004aaa534
Fig 7. Most commonly used power supply connection.
7.9 Power-on reset (POR)
When VCC(5V0) is directly connected to the RESET_N pin, the internal POR pulse width
(tPORP) will be typically 800 ns. The pulse is started when VCC(5V0) rises above VTRIP
(1.2 V).
To give a better view of the functionality, Figure 8 shows a possible curve of VCC(5V0) with
dips at t2–t3 and t4–t5. If the dip at t4–t5 is too short (that is, < 11 µs), the internal POR
pulse will not react and will remain LOW. The internal POR starts with a 1 at t0. At t1, the
detector will see the passing of the trip level and a delay element will add another tPORP
before it drops to 0.
The internal POR pulse will be generated whenever VCC(5V0) drops below VTRIP for more
than 11 µs.
VCC(5V0)
VTRIP
t0
t1
t2
tPORP
t4
t3
tPORP
t5
PORP(1)
004aaa584
(1) PORP = power-on reset pulse.
Fig 8. Internal power-on reset timing.
The RESET_N pin can be either connected to VCC(I/O) (using the internal POR circuit) or
externally controlled (by the microcontroller, ASIC, and so on). Figure 9 shows the
availability of the clock with respect to the external POR.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
25 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
RESET_N
EXTERNAL CLOCK
004aaa583
A
Stable external clock is available at A.
Fig 9. Clock with respect to the external power-on reset.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
26 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
8. Registers
Table 5 shows the bit description of the registers.
• All registers range from 0000h to 03FFh. These registers can be read or written as
double word, that is 32-bit data. In the case of a 16-bit data bus width, two subsequent
accesses are necessary to complete the register read or write cycle.
• Operational registers range from 0000h to 01FFh. Configuration registers range from
0300h to 03FFh.
Table 5:
Register overview
Address
Register
Reset value
References
EHCI capability registers
0000h
CAPLENGTH
20h
Section 8.1.1 on page 28
0002h
HCIVERSION
0100h
Section 8.1.2 on page 28
0004h
HCSPARAMS
0000 0011h
Section 8.1.3 on page 28
0008h
HCCPARAMS
0000 0086h
Section 8.1.4 on page 29
EHCI operational registers
0020h
USBCMD
0008 0000h
Section 8.2.1 on page 30
0024h
USBSTS
0000 1000h
Section 8.2.2 on page 31
0028h
USBINTR
0000 0000h
Section 8.2.3 on page 32
002Ch
FRINDEX
0000 0000h
Section 8.2.4 on page 33
0030h
CTRLDSSEGMENT
0000 0000h
Section 8.2.5 on page 34
0060h
CONFIGFLAG
0000 0000h
Section 8.2.6 on page 34
0064h
PORTSC1
0000 2000h
Section 8.2.7 on page 35
0130h
ISO PTD Done Map
0000 0000h
Section 8.2.8 on page 36
0134h
ISO PTD Skip Map
FFFF FFFFh
Section 8.2.9 on page 37
0138h
ISO PTD Last PTD
0000 0000h
Section 8.2.10 on page 37
0140h
INT PTD Done Map
0000 0000h
Section 8.2.11 on page 37
0144h
INT PTD Skip Map
FFFF FFFFh
Section 8.2.12 on page 38
0148h
INT PTD Last PTD
0000 0000h
Section 8.2.13 on page 38
0150h
ATL PTD Done Map
0000 0000h
Section 8.2.14 on page 38
0154h
ATL PTD Skip Map
FFFF FFFFh
Section 8.2.15 on page 38
0158h
ATL PTD Last PTD
0000 0000h
Section 8.2.16 on page 39
0200h–02FFh
reserved
-
-
Configuration registers
0300h
HW Mode Control
0000 0000h
Section 8.3.1 on page 39
0304h
Chip ID
0001 1761h
Section 8.3.2 on page 41
0308h
Scratch
0000 0000h
Section 8.3.3 on page 41
030Ch
SW Reset
0000 0000h
Section 8.3.4 on page 41
0330h
DMA Configuration
0000 0000h
Section 8.3.5 on page 42
0334h
Buffer Status
0000 0000h
Section 8.3.6 on page 43
0338h
ATL Done Timeout
0000 0000h
Section 8.3.7 on page 44
033Ch
Memory
0000 0000h
Section 8.3.8 on page 44
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
27 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 5:
Register overview…continued
Address
Register
Reset value
References
0340h
Edge Interrupt Count
0000 000Fh
Section 8.3.9 on page 45
0344h
DMA Start Address
0000 0000h
Section 8.3.10 on page 46
0354h
Power Down Control
03E8 1BA0h
Section 8.3.11 on page 46
0374h
Port 1 Control
0086 0086h
Section 8.3.12 on page 48
Interrupt registers
0310h
Interrupt
0000 0000h
Section 8.4.1 on page 50
0314h
Interrupt Enable
0000 0000h
Section 8.4.2 on page 51
0318h
ISO IRQ Mask OR
0000 0000h
Section 8.4.3 on page 53
031Ch
INT IRQ Mask OR
0000 0000h
Section 8.4.4 on page 53
0320h
ATL IRQ Mask OR
0000 0000h
Section 8.4.5 on page 53
0324h
ISO IRQ Mask AND
0000 0000h
Section 8.4.6 on page 54
0328h
INT IRQ Mask AND
0000 0000h
Section 8.4.7 on page 54
032Ch
ATL IRQ Mask AND
0000 0000h
Section 8.4.8 on page 54
8.1 EHCI capability registers
8.1.1 CAPLENGTH register (R: 0000h)
The bit description of the Capability Length (CAPLENGTH) register is given in Table 6.
Table 6:
CAPLENGTH register: bit description
Bit
Symbol
Access
Value
Description
7 to 0
CAPLENGTH
[7:0]
R
20h
Capability Length: This is used as an offset. It
is added to the register base to find the
beginning of the operational register space.
8.1.2 HCIVERSION register (R: 0002h)
Table 7 shows the bit description of the Host Controller Interface Version Number
(HCIVERSION) register.
Table 7:
HCIVERSION register: bit description
Bit
Symbol
15 to 0
HCIVERSION R
[15:0]
Access Value
0100h
Description
Host Controller Interface Version Number: It
contains a BCD encoding of the version number of
the interface to which the Host Controller interface
conforms.
8.1.3 HCSPARAMS register (R: 0004h)
The Host Controller Structural Parameters (HCSPARAMS) register is a set of fields that
are structural parameters. The bit allocation is given in Table 8.
Table 8:
HCSPARAMS register: bit allocation
Bit
31
30
29
28
Symbol
27
26
25
24
reserved
Reset
0
0
0
0
0
0
0
0
Access
R
R
R
R
R
R
R
R
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
28 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Bit
23
22
Symbol
21
20
19
DPN[3:0]
18
17
reserved
16
P_INDI
CATOR
Reset
0
0
0
0
0
0
0
0
Access
R
R
R
R
R
R
R
R
Bit
15
14
13
12
11
10
9
8
Symbol
N_CC[3:0]
N_PCC[3:0]
Reset
0
0
0
0
0
0
0
0
Access
R
R
R
R
R
R
R
R
7
6
4
3
2
1
0
Bit
Symbol
PRR
5
reserved
PPC
N_PORTS[3:0]
Reset
0
0
0
1
0
0
0
1
Access
R
R
R
R
R
R
R
R
Table 9:
HCSPARAMS register: bit description
Bit
Symbol
Description [1]
31 to 24
-
reserved; write logic 0
23 to 20
DPN[3:0]
Debug Port Number: This field identifies which of the Host
Controller ports is the debug port.
19 to 17
-
reserved; write logic 0
16
P_INDICATOR
Port Indicators: This bit indicates whether the ports support port
indicator control.
15 to 12
N_CC[3:0]
Number of Companion Controller: This field indicates the number
of companion controllers associated with this Hi-Speed USB Host
Controller.
11 to 8
N_PCC[3:0]
Number of Ports per Companion Controller: This field indicates
the number of ports supported per companion Host Controller.
7
PRR
Port Routing Rules: This field indicates the method used for
mapping ports to the companion controllers.
6 to 5
-
reserved; write logic 0
4
PPC
Port Power Control: This field indicates whether the Host Controller
implementation includes port power control.
3 to 0
N_PORTS[3:0]
N_Ports: This field specifies the number of physical downstream
ports implemented on this Host Controller.
[1]
For details on register bit description, refer to Enhanced Host Controller Interface Specification for Universal
Serial Bus Rev. 1.0.
8.1.4 HCCPARAMS register (R: 0008h)
The Host Controller Capability Parameters (HCCPARAMS) register is a four-byte register,
and the bit allocation is given in Table 10.
Table 10:
HCCPARAMS register: bit allocation
Bit
31
30
29
28
Symbol
27
26
25
24
reserved
Reset
0
0
0
0
0
0
0
0
Access
R
R
R
R
R
R
R
R
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
29 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Bit
23
22
21
20
19
18
17
16
Reset
0
0
0
0
0
0
0
0
Access
R
R
R
R
R
R
R
R
Bit
15
14
13
12
11
10
9
8
Reset
0
0
0
0
0
0
0
0
Access
R
R
R
R
R
R
R
R
Bit
7
6
5
4
3
2
1
0
reserved
ASPC
PFLF
64AC
Reset
1
0
0
0
0
1
1
0
Access
R
R
R
R
R
R
R
R
Symbol
reserved
Symbol
EECP[7:0]
Symbol
IST[3:0]
Table 11:
HCCPARAMS register: bit description
Bit
Symbol
Description [1]
31 to 16
-
reserved; write logic 0
15 to 8
EECP[7:0] EHCI Extended Capabilities Pointer: Default = implementation
dependent. This optional field indicates the existence of a capabilities list.
7 to 4
IST[3:0]
3
-
reserved; write logic 0
2
ASPC
Asynchronous Schedule Park Capability: Default = implementation
dependent. If this bit is set to logic 1, the Host Controller supports the park
feature for high-speed queue heads in the Asynchronous Schedule.
1
PFLF
Programmable Frame List Flag: Default = implementation dependent. If
this bit is cleared, the system software must use a frame list length of
1024 elements with this Host Controller.
Isochronous Scheduling Threshold: Default = implementation
dependent. This field indicates, relative to the current position of the
executing Host Controller, where software can reliably update the
isochronous schedule.
If PFLF is set, the system software can specify and use a smaller frame
list and configure the host through the FLS field of the USBCMD register.
0
[1]
64AC
64-bit Addressing Capability: This field contains the addressing range
capability.
For details on register bit description, refer to Enhanced Host Controller Interface Specification for Universal
Serial Bus Rev. 1.0.
8.2 EHCI operational registers
8.2.1 USBCMD register (R/W: 0020h)
The USB Command (USBCMD) register indicates the command to be executed by the
serial Host Controller. Writing to this register causes a command to be executed. Table 12
shows the USBCMD register bit allocation.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
30 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 12:
USBCMD register: bit allocation
Bit
31
30
29
28
27
Symbol
Reset
Access
Bit
24
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
23
22
21
20
19
18
17
16
ITC[7:0]
Reset
Access
Bit
0
0
0
0
1
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
15
14
13
12
11
10
9
8
reserved [1]
Symbol
Reset
Access
Bit
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
7
6
5
4
3
2
1
0
HCRESET
RS
reserved [1]
LHCR
Reset
Access
[1]
25
R/W
Symbol
Symbol
26
reserved [1]
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
The reserved bits should always be written with the reset value.
Table 13:
USBCMD register: bit description
Bit
Symbol
Description [1]
31 to 24
-
reserved; write logic 0
23 to 16
ITC[7:0]
Interrupt Threshold Control: This field is used by the system software to
select the maximum rate at which the Host Controller will issue interrupts.
15 to 8
-
reserved
7
LHCR
Light Host Controller Reset (optional): If implemented, it allows the
driver software to reset the EHCI controller without affecting the state of
the ports or the relationship to the companion Host Controllers. If not
implemented, a read of this field will always return logic 0.
6 to 2
-
reserved
1
HCRESET Host Controller Reset: This control bit is used by the software to reset
the Host Controller.
0
RS
[1]
Run/Stop: 1 = Run, 0 = Stop. When set, the Host Controller executes the
schedule.
For details on register bit description, refer to Enhanced Host Controller Interface Specification for Universal
Serial Bus Rev. 1.0.
8.2.2 USBSTS register (R/W: 0024h)
The USB Status (USBSTS) register indicates pending interrupts and various states of the
Host Controller. The status resulting from a transaction on the serial bus is not indicated in
this register. Software clears the register bits by writing ones to them. The bit allocation is
given in Table 14.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
31 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 14:
USBSTS register: bit allocation
Bit
31
30
29
28
Symbol
Reset
Access
Bit
26
25
24
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
23
22
21
20
19
18
17
16
reserved [1]
Symbol
Reset
Access
Bit
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
15
14
13
12
11
10
9
8
reserved [1]
Symbol
Reset
Access
Bit
0
0
0
1
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
7
6
5
4
3
2
1
0
reserved [1]
Symbol
Reset
Access
[1]
27
reserved [1]
FLR
reserved [1]
PCD
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
The reserved bits should always be written with the reset value.
Table 15:
USBSTS register: bit description
Symbol Description [1]
Bit
31 to 4 -
reserved; write logic 0
3
FLR
Frame List Rollover: The Host Controller sets this bit to logic 1 when the
Frame List Index rolls over from its maximum value to zero.
2
PCD
Port Change Detect: The Host Controller sets this bit to logic 1 when any port,
where the PO bit is cleared, has a change to a one or a FPR bit changes to a
one as a result of a J-K transition detected on a suspended port.
1 to 0
-
reserved
[1]
For details on register bit description, refer to Enhanced Host Controller Interface Specification for Universal
Serial Bus Rev. 1.0.
8.2.3 USBINTR register (R/W: 0028h)
The USB Interrupt Enable (USBINTR) register enables and disables reporting of the
corresponding interrupt to the software. When a bit is set and the corresponding interrupt
is active, an interrupt is generated to the host. Interrupt sources that are disabled in this
register still appear in USBSTS to allow the software to poll for events. The USBINTR
register bit allocation is given in Table 16.
Table 16:
USBINTR register: bit allocation
Bit
31
30
29
28
Symbol
Reset
Access
27
26
25
24
reserved [1]
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
32 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Bit
23
22
21
20
Symbol
Reset
Access
Bit
18
17
16
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
15
14
13
12
11
10
9
8
reserved [1]
Symbol
Reset
Access
Bit
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
7
6
5
4
3
2
1
0
reserved [1]
Access
reserved [1]
FLRE
PCIE
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Symbol
Reset
[1]
19
reserved [1]
The reserved bits should always be written with the reset value.
Table 17:
USBINTR register: bit description
Bit
Symbol
Description [1]
31 to 4
-
reserved
3
FLRE
Frame List Rollover Enable: When this bit is set and the FLR bit in the
USBSTS register is set, the Host Controller issues an interrupt. The
interrupt is acknowledged by software clearing bit FLR.
2
PCIE
Port Change Interrupt Enable: When this bit is set and the PCD bit in the
USBSTS register is set, the Host Controller issues an interrupt. The
interrupt is acknowledged by software clearing bit PCD.
1 to 0
-
reserved
[1]
For details on register bit description, refer to Enhanced Host Controller Interface Specification for Universal
Serial Bus Rev. 1.0.
8.2.4 FRINDEX register (R/W: 002Ch)
The Frame Index (FRINDEX) register is used by the Host Controller to index into the
periodic frame list. The register updates every 125 µs (once each microframe). Bits n to 3
are used to select a particular entry in the Periodic Frame List during periodic schedule
execution. The number of bits used for the index depends on the size of the frame list as
set by the system software in the FLS (Frame List Size) field of the USBCMD register.
This register must be written as a Double Word. A Word-only write (16-bit mode) produces
undefined results. This register cannot be written unless the Host Controller is in the
halted state as indicated by the HCH (HCHalted) bit. A write to this register while the RS
(Run/Stop) bit is set produces undefined results. Writes to this register also affect the SOF
value. The bit allocation is given in Table 18.
Table 18:
FRINDEX register: bit allocation
Bit
31
30
29
28
Symbol
Reset
Access
27
26
25
24
reserved [1]
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
33 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Bit
23
22
21
20
Symbol
Reset
Access
Bit
18
17
16
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
15
14
13
12
11
10
9
8
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
reserved [1]
Symbol
Reset
Access
Bit
FRINDEX[13:8]
Symbol
FRINDEX[7:0]
Reset
Access
[1]
19
reserved [1]
The reserved bits should always be written with the reset value.
Table 19:
Bit
FRINDEX register: bit description
Description [1]
Symbol
31 to 14 13 to 0
[1]
reserved
FRINDEX[13:0] Frame Index: Bits in this register are used for the frame number in the
SOF packet and as the index into the Frame List. The value in this
register increments at the end of each time frame (for example,
microframe).
For details on register bit description, refer to Enhanced Host Controller Interface Specification for Universal
Serial Bus Rev. 1.0.
8.2.5 CTRLDSSEGMENT register (R/W: 0030h)
The Control Data Structure Segment (CTRLDSSEGMENT) register corresponds to the
most significant address bits (63 to 32) for all EHCI data structures. If the 64AC (64-bit
Addressing Capability) field in HCCPARAMS is cleared, then this register is not used and
software cannot write to it (reading from this register returns zero).
If the 64AC (64-bit Addressing Capability) field in HCCPARAMS is set, this register is used
with link pointers to construct 64-bit addresses to EHCI control data structures. This
register is concatenated with the link pointer from either the PERIODICLISTBASE,
ASYNCLISTADDR, or any control data structure link field to construct a 64-bit address.
This register allows the host software to locate all control data structures within the same
4 gigabytes memory segment.
8.2.6 CONFIGFLAG register (R/W: 0060h)
The bit allocation of the Configure Flag (CONFIGFLAG) register is given in Table 20.
Table 20:
CONFIGFLAG register: bit allocation
Bit
31
30
29
28
Symbol
Reset
Access
27
25
24
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
9397 750 13257
Product data sheet
26
reserved [1]
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
34 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Bit
23
22
21
20
Symbol
Reset
Access
Bit
18
17
16
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
15
14
13
12
11
10
9
8
reserved [1]
Symbol
Reset
Access
Bit
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
7
6
5
4
3
2
1
0
reserved [1]
Symbol
Reset
Access
[1]
19
reserved [1]
CF
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
The reserved bits should always be written with the reset value.
Table 21:
CONFIGFLAG register: bit description
Bit
Symbol Description [1]
31 to 1
-
reserved
0
CF
Configure Flag: The host software sets this bit as the last action when it is
configuring the Host Controller. This bit controls the default port-routing
control logic.
[1]
For details on register bit description, refer to Enhanced Host Controller Interface Specification for Universal
Serial Bus Rev. 1.0.
8.2.7 PORTSC1 register (R/W: 0064h)
The Port Status and Control (PORTSC) register (bit allocation: Table 22) is in the power
well. It is reset by hardware only when the auxiliary power is initially applied or in response
to a Host Controller reset. The initial conditions of a port are:
• No peripheral connected
• Port disabled.
If the port has power control, software cannot change the state of the port until it sets the
port power bits. Software must not attempt to change the state of the port until the power
is stable on the port (maximum delay is 20 ms from the transition).
Table 22:
PORTSC1 register: bit allocation
Bit
31
30
29
28
Reset
Access
Bit
Access
26
25
24
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
23
22
21
20
19
18
17
16
reserved [1]
Symbol
Reset
27
reserved [1]
Symbol
PTC[3:0]
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
35 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Bit
15
Symbol
14
13
11
10
8
reserved [1]
PR
PO
PP
0
0
1
0
0
0
0
0
Access
R
R
R/W
R/W
R/W
R/W
R/W
R
Bit
7
6
5
4
3
2
1
0
reserved [1]
SUSP
FPR
PED
ECSC
ECCS
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R
Reset
Access
[1]
LS[1:0]
9
Reset
Symbol
PIC[1:0]
12
The reserved bits should always be written with the reset value.
Table 23:
PORTSC1 register: bit description
Bit
Symbol
Description [1]
31 to 20
-
reserved
19 to 16
PTC[3:0]
Port Test Control: When this field is zero, the port is not operating in a
test mode. A non-zero value indicates that it is operating in test mode
indicated by the value.
15 to 14
PIC[1:0]
Port Indicator Control: Writing to this field has no effect if the
P_INDICATOR bit in the HCSPARAMS register is logic 0.
For a description on how these bits are implemented, refer to Universal
Serial Bus Specification Rev. 2.0. [2]
13
PO
Port Owner: This bit unconditionally goes to logic 0 when the configured
bit in the CONFIGFLAG register makes a logic 0 to logic 1 transition. This
bit unconditionally goes to logic 1 whenever the configured bit is logic 0.
12
PP
Port Power: The function of this bit depends on the value of the PPC (Port
Power Control) field in the HCSPARAMS register.
11 to 10
LS[1:0]
Line Status: This field reflect the current logical levels of the DP (bit 11)
and DM (bit 10) signal lines.
9
-
reserved
8
PR
Port Reset: Logic 1 means the port is in the reset state. Logic 0 means
the port is not in reset. [2]
7
SUSP
Suspend: Logic 1 means the port is in the suspend state. Logic 0 means
the port is not suspended. [2]
6
FPR
Force Port Resume: Logic 1 means resume detected or driven on the
port. Logic 0 means no resume (K-state) detected or driven on the port. [2]
5 to 3
-
reserved
2
PED
Port Enabled/Disabled: Logic 1 means enable. Logic 0 means disable. [2]
1
ECSC
Connect Status Change: Logic 1 means change in ECCS. Logic 0
means no change. [2]
0
ECCS
Current Connect Status: Logic 1 indicates a device is present on the
port. Logic 0 indicates no device is present. [2]
[1]
For details on register bit description, refer to Enhanced Host Controller Interface Specification for Universal
Serial Bus Rev. 1.0.
[2]
These fields read logic 0, if the PP (Port Power) bit in register PORTSC1 is logic 0.
8.2.8 ISO PTD Done Map register (R: 0130h)
The bit description of the register is given in Table 24.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
36 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 24:
ISO PTD Done Map register: bit description
Bit
Symbol
Access Value
31 to 0
ISO_PTD_DONE_
MAP[31:0]
R
Description
0000 0000h ISO PTD Done Map: Done map for each
of the 32 PTDs for the ISO transfer
This register represents a direct map of the done status of the 32 PTDs. The bit
corresponding to a certain PTD will be set to logic 1 as soon as that PTD execution is
completed. Reading the Done Map register will clear all the bits that are set to logic 1, and
the next reading will reflect the updated status of new executed PTDs.
8.2.9 ISO PTD Skip Map register (R/W: 0134h)
Table 25 shows the bit description of the register.
Table 25:
ISO PTD Skip Map register: bit description
Bit
Symbol
Access
Value
Description
31 to 0
ISO_PTD_SKIP_
MAP[31:0]
R/W
FFFF FFFFh
ISO PTD Skip Map: Skip map for each
of the 32 PTDs for the ISO transfer.
When a bit in the PTD Skip Map is set to logic 1 that PTD will be skipped although its V bit
may be set. The information in that PTD is not processed. For example, NextPTDPointer
will not affect the order of processing of PTDs. The Skip bit should not be normally set on
the position indicated by NextPTDPointer.
8.2.10 ISO PTD Last PTD register (R/W: 0138h)
Table 26 shows the bit description of the ISO PTD Last PTD register.
Table 26:
ISO PTD Last PTD register: bit description
Bit
Symbol
Access
Value
Description
31 to 0
ISO_PTD_LAST_
PTD[31:0]
R/W
0000 0000h
ISO PTD last PTD: Last PTD of the
32 PTDs is indicated by the 32 bitmap.
1h — One PTD in ISO
2h — Two PTDs in ISO
4h — Three PTDs in ISO.
Once the LastPTD bit corresponding to a PTD is set, this will be the last PTD processed
(checking V = 1) in that PTD category. Subsequently, the process will restart with the first
PTD (of that group). This is useful to reduce the time in which all the PTDs (the respective
memory space) would be checked, especially if only a few PTDs are defined. The
LastPTD bit must be normally set to a higher position than any other position indicated by
the NextPTDPointer from an active PTD.
8.2.11 INT PTD Done Map register (R: 0140h)
The bit description of the register is given in Table 27.
Table 27:
INT PTD Done Map register: bit description
Bit
Symbol
Access
Value
31 to 0
INT_PTD_DONE_
MAP[31:0]
R
0000 0000h INT PTD Done Map: Done map for each
of the 32 PTDs for the INT transfer
9397 750 13257
Product data sheet
Description
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
37 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
This register represents a direct map of the done status of the 32 PTDs. The bit
corresponding to a certain PTD will be set to logic 1 as soon as that PTD execution is
completed. Reading the Done Map register will clear all the bits that are set to logic 1, and
the next reading will reflect the updated status of new executed PTDs.
8.2.12 INT PTD Skip Map register (R/W: 0144h)
Table 28 shows the bit description of the INT PTD Skip Map register.
Table 28:
INT PTD Skip Map register: bit description
Bit
Symbol
Access
Value
Description
31 to 0
INT_PTD_SKIP_
MAP[31:0]
R/W
FFFF FFFFh
INT PTD Skip Map: Skip map for each
of the 32 PTDs for the INT transfer
When a bit in the PTD Skip Map is set to logic 1 that PTD will be skipped although its V bit
may be set. The information in that PTD is not processed. For example, NextPTDPointer
will not affect the order of processing of PTDs. The Skip bit should not be normally set on
the position indicated by NextPTDPointer.
8.2.13 INT PTD Last PTD register (R/W: 0148h)
The bit description of the register is given in Table 29.
Table 29:
INT PTD Last PTD register: bit description
Bit
Symbol
Access
Value
Description
31 to 0
INT_PTD_LAST
_PTD[31:0]
R/W
0000 0000h INT PTD Last PTD: Last PTD of the
32 PTDs as indicated by the 32 bitmap.
1h — One PTD in INT
2h — Two PTDs in INT
3h — Three PTDs in INT.
Once the LastPTD bit corresponding to a PTD is set, this will be the last PTD processed
(checking V = 1) in that PTD category. Subsequently, the process will restart with the first
PTD (of that group). This is useful to reduce the time in which all the PTDs (the respective
memory space) would be checked, especially if only a few PTDs are defined. The
LastPTD bit must be normally set to a higher position than any other position indicated by
the NextPTDPointer from an active PTD.
8.2.14 ATL PTD Done Map register (R: 0150h)
Table 30 shows the bit description of the ATL PTD Done Map register.
Table 30:
Bit
ATL PTD Done Map register: bit description
Symbol
31 to 0 ATL_PTD_DONE
_MAP[31:0]
Access
Value
Description
R
0000 0000h
ATL PTD Done Map: Done map for
each of the 32 PTDs for the ATL transfer
This register represents a direct map of the done status of the 32 PTDs. The bit
corresponding to a certain PTD will be set to logic 1 as soon as that PTD execution is
completed. Reading the Done Map register will clear all the bits that are set to logic 1, and
the next reading will reflect the updated status of new executed PTDs.
8.2.15 ATL PTD Skip Map register (R/W: 0154h)
The bit description of the register is given in Table 31.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
38 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 31:
Bit
ATL PTD Skip Map register: bit description
Symbol
31 to 0 ATL_PTD_SKIP
_MAP[31:0]
Access Value
Description
R/W
ATL PTD Skip Map: Skip map for each of
the 32 PTDs for the ATL transfer
FFFF FFFFh
When a bit in the PTD Skip Map is set to logic 1 that PTD will be skipped although its V bit
may be set. The information in that PTD is not processed. For example, NextPTDPointer
will not affect the order of processing of PTDs. The Skip bit should not be normally set on
the position indicated by NextPTDPointer.
8.2.16 ATL PTD Last PTD register (R/W: 0158h)
The bit description of the ATL PTD Last PTD register is given in Table 32.
Table 32:
ATL PTD Last PTD register: bit description
Bit
Symbol
Access
Value
Description
31 to 0
ATL_PTD_
LAST_PTD
[31:0]
R/W
0000 0000h
ATL PTD Last PTD: Last PTD of the
32 PTDs as indicated by the 32 bitmap.
1h — One PTD in ATL
2h — Two PTDs in ATL
4h — Three PTDs in ATL.
Once the LastPTD bit corresponding to a PTD is set, this will be the last PTD processed
(checking V = 1) in that PTD category. Subsequently, the process will restart with the first
PTD (of that group). This is useful to reduce the time in which all the PTDs (the respective
memory space) would be checked, especially if only a few PTDs are defined. The
LastPTD bit must be normally set to a higher position than any other position indicated by
the NextPTDPointer from an active PTD.
8.3 Configuration registers
8.3.1 HW Mode Control register (R/W: 0300h)
Table 33 shows the bit allocation of the register.
Table 33:
HW Mode Control register: bit allocation
Bit
Symbol
31
30
29
28
Access
Bit
26
25
24
reserved [1]
ALL_ATX_
RESET
Reset
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
23
22
21
20
19
18
17
16
reserved [1]
Symbol
Reset
Access
Bit
Symbol
27
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
15
14
13
12
11
10
9
8
reserved [1]
ANA_DIGI
_OC
Reset
Access
DATA_BUS
_WIDTH
0
0
0
0
0
0
0
1
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
39 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Bit
7
Symbol
5
4
3
reserved [1]
2
1
0
INTR_POL
INTR_
LEVEL
GLOBAL_
INTR_EN
reserved
DACK_
POL
DREQ_
POL
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
Access
[1]
6
The reserved bits should always be written with the reset value.
Table 34:
HW Mode Control register: bit description
Bit
Symbol
Description
31
ALL_ATX_
RESET
All ATX Reset: For debugging purposes (not used normally).
1 — Enable reset, then write back logic 0
0 — No reset.
30 to 16
-
reserved; write logic 0
15
ANA_DIGI_OC
Analog Digital Overcurrent: This bit selects analog or digital
overcurrent detection on pins OC1_N, OC2_N and OC3_N.
0 — Digital overcurrent
1 — Analog overcurrent.
14 to 9
-
reserved; write logic 0
8
DATA_BUS_
WIDTH
Data Bus Width:
0 — defines a 16-bit data bus width
1 — sets a 32-bit data bus width.
7
-
reserved; write logic 0
6
DACK_POL
DACK Polarity:
1 — indicates that the DACK input is active HIGH
0 — indicates active LOW.
5
DREQ_POL
DREQ Polarity:
1 — indicates that the DREQ output is active HIGH
0 — indicates active LOW.
4 to 3
-
reserved; write logic 0
2
INTR_POL
Interrupt Polarity:
0 — active LOW
1 — active HIGH.
1
INTR_LEVEL
Interrupt Level:
0 — INT level triggered
1 — INT is edge triggered. A pulse of certain width is generated.
0
GLOBAL_INTR Global Interrupt Enable: This bit must be set to logic 1 to enable the
_EN
IRQ signal assertion.
0 — IRQ assertion is disabled. IRQ will never be asserted,
regardless of other settings or IRQ events.
1 — IRQ assertion is enabled. IRQ will be asserted according to the
Interrupt Enable register, and events setting and occurrence.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
40 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
8.3.2 Chip ID register (R: 0304h)
Read this register to get the ID of the ISP1760. The upper word of the register contains
the hardware version number and the lower word contains the chip ID. Table 35 shows the
bit description of the register.
Table 35:
Bit
Chip ID register: bit description
Symbol
31 to 0 CHIPID
[31:0]
Access Value
Description
R
Chip ID: This register represents the hardware
version number (0001h) and the chip ID (1761h).
0001 1761h
Remark: The chip ID is for internal use to identify
the ISP176x product family.
8.3.3 Scratch register (R/W: 0308h)
This register is for testing and debugging purposes only. The value read back must be the
same as the value that was written. The bit description of this register is given in Table 36.
Table 36:
Scratch register: bit description
Bit
Symbol
Access
Value
Description
31 to 0
SCRATCH[31:0]
R/W
0000 0000h
Scratch: For testing and debugging
purposes
8.3.4 SW Reset register (R/W: 030Ch)
Table 37 shows the bit allocation of the register.
Table 37:
SW Reset register: bit allocation
Bit
31
30
29
28
Symbol
Reset
Access
Bit
Access
Bit
Access
Bit
Access
[1]
24
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
23
22
21
20
19
18
17
16
reserved [1]
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
15
14
13
12
11
10
9
8
reserved [1]
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
7
6
5
4
3
2
1
0
RESET_
HC
RESET_
ALL
reserved [1]
Symbol
Reset
25
0
Symbol
Reset
26
0
Symbol
Reset
27
reserved [1]
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
The reserved bits should always be written with the reset value.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
41 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 38:
SW Reset register: bit description
Bit
Symbol
Description
31 to 2
-
reserved; write logic 0
1
RESET_HC
Reset Host Controller: Reset only the Host Controller-specific registers
(only registers with address below 300h).
0 — No reset
1 — Enable reset.
0
RESET_ALL Reset All: Reset all the Host Controller and CPU interface registers.
0 — No reset
1 — Enable reset.
8.3.5 DMA Configuration register (R/W: 0330h)
The bit allocation of the DMA Configuration register is given in Table 39.
Table 39:
DMA Configuration register: bit allocation
Bit
31
30
29
0
0
0
0
R/W
R/W
R/W
23
22
21
0
0
0
0
R/W
R/W
R/W
15
14
13
0
0
0
0
R/W
R/W
R/W
7
6
5
Symbol
Reset
Access
Bit
Access
Bit
Access
Bit
Access
[1]
25
24
0
0
0
0
R/W
R/W
R/W
R/W
R/W
20
19
18
17
16
0
0
0
0
R/W
R/W
R/W
R/W
R/W
12
11
10
9
8
0
0
0
0
R/W
R/W
R/W
R/W
R/W
4
3
2
1
0
ENABLE_
DMA
DMA_READ
_WRITE_
SEL
DMA_COUNTER[7:0]
reserved [1]
Symbol
Reset
26
DMA_COUNTER[15:8]
Symbol
Reset
27
DMA_COUNTER[23:16]
Symbol
Reset
28
BURST_LEN[1:0]
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
The reserved bits should always be written with the reset value.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
42 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 40:
DMA Configuration register: bit description
Bit
Symbol
Description
31 to 8
DMA_COUNTER
[23:0]
DMA Counter: The number of bytes to be transferred (read or
write).
Remark: Different number of bursts will be generated for the
same transfer length programmed in 16-bit and 32-bit modes
because DMA_COUNTER is in number of bytes.
7 to 4
-
reserved
3 to 2
BURST_LEN[1:0]
DMA Burst Length:
00 — Single DMA burst
01 — 4-cycle DMA burst
10 — 8-cycle DMA burst
11 — 16-cycle DMA burst.
1
ENABLE_DMA
Enable DMA:
0 — Terminate DMA
1 — Enable DMA.
0
DMA_READ_
WRITE_SEL
DMA Read/Write Select: Indicates if the DMA operation is a
write or read (to or from the ISP1760).
0 — DMA write to the ISP1760 internal RAM is set
1 — DMA read from the ISP1760 internal RAM.
8.3.6 Buffer Status register (R/W: 0334h)
Table 41 shows the bit allocation of the Buffer Status register.
Table 41:
Buffer Status register: bit allocation
Bit
31
30
29
28
Symbol
Reset
Access
Bit
Access
Bit
Access
Bit
Access
[1]
24
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
23
22
21
20
19
18
17
16
reserved [1]
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
15
14
13
12
11
10
9
8
reserved [1]
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
7
6
5
4
3
2
1
0
ISO_BUF_
FILL
INT_BUF_
FILL
ATL_BUF_
FILL
reserved [1]
Symbol
Reset
25
0
Symbol
Reset
26
R/W
Symbol
Reset
27
reserved [1]
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
The reserved bits should always be written with the reset value.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
43 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 42:
Buffer Status register: bit description
Bit
Symbol
Description
31 to 3
-
reserved
2
ISO_BUF_
FILL
ISO Buffer Filled:
1 — Indicates one of the ISO PTDs is filled, and the ISO PTD area will
be processed
0 — Indicates there is no PTD in this area. Therefore, processing of
the ISO PTDs will be completely skipped.
1
INT_BUF_
FILL
INT Buffer Filled:
1 — Indicates one of the INT PTDs is filled, and the INT PTD area will
be processed
0 — Indicates there is no PTD in this area. Therefore, processing of
the INT PTDs will be completely skipped.
0
ATL_BUF_
FILL
ATL Buffer Filled:
1 — Indicates one of the ATL PTDs is filled, and the ATL PTD area will
be processed
0 — Indicates there is no PTD in this area. Therefore, processing of
the ATL PTDs will be completely skipped.
8.3.7 ATL Done Timeout register (R/W: 0338h)
The bit description of the ATL Done Timeout register is given in Table 43.
Table 43:
ATL Done Timeout register: bit description
Bit
Symbol
Access Value
31 to 0
ATL_DONE R/W
_TIMEOUT
[31:0]
Description
0000 0000h ATL Done Timeout: This register determines the
ATL done timeout interrupt. This register defines
the timeout in ms after which the ISP1760 asserts
the INT line, if enabled. It is applicable to the ATL
done PTDs only.
8.3.8 Memory register (R/W: 033Ch)
The Memory register contains the base memory read address and the respective bank.
This register needs to be set only before a first memory read cycle. Once written, the
address will be latched for the bank and will be incremented for every read of that bank,
until a new address for that bank is written to change the address pointer.
The bit description of the register is given in Table 44.
Table 44:
Memory register: bit allocation
Bit
31
30
29
28
Symbol
Reset
Access
Bit
Access
26
25
24
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
23
22
21
20
19
18
17
16
reserved [1]
Symbol
Reset
27
reserved [1]
MEM_BANK_SEL[1:0]
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
44 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Bit
15
14
13
0
0
0
0
R/W
R/W
R/W
7
6
5
0
0
0
0
R/W
R/W
R/W
R/W
Symbol
12
10
9
8
0
0
0
0
R/W
R/W
R/W
R/W
R/W
4
3
2
1
0
0
0
0
0
R/W
R/W
R/W
R/W
START_ADDR_MEM_READ[15:8]
Reset
Access
Bit
Symbol
START_ADDR_MEM_READ[7:0]
Reset
Access
[1]
11
The reserved bits should always be written with the reset value.
Table 45:
Memory register: bit description
Bit
Symbol
Description
31 to 18
-
reserved
17 to 16
MEM_BANK_
SEL[1:0]
Memory Bank Select: Up to four memory banks can be selected.
For details on internal memory read description, see Section 7.3.1.
Applicable to PIO mode memory read or write data transfers only.
15 to 0
START_
Start Address for Memory Read Cycles: The start address for a
ADDR_MEM_ series of memory read cycles at incremental addresses in a
READ[15:0]
contiguous space. Applicable to PIO mode memory read data
transfers only.
8.3.9 Edge Interrupt Count register (R/W: 0340h)
Table 46 shows the bit allocation of the register.
Table 46:
Edge Interrupt Count register: bit allocation
Bit
31
30
29
0
0
0
0
R/W
R/W
R/W
23
22
21
Symbol
Reset
Access
Bit
28
26
25
24
0
0
0
0
R/W
R/W
R/W
R/W
R/W
20
19
18
17
16
MIN_WIDTH[7:0]
reserved [1]
Symbol
Reset
Access
Bit
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
15
14
13
12
11
10
9
8
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
7
6
5
4
3
2
1
0
0
0
0
0
1
1
1
1
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Symbol
Reset
Access
Bit
NO_OF_CLK[15:8]
Symbol
Reset
Access
[1]
27
NO_OF_CLK[7:0]
The reserved bits should always be written with the reset value.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
45 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 47:
Edge Interrupt Count register: bit description
Bit
Symbol
Description
31 to 24
MIN_
WIDTH[7:0]
Minimum Width: Indicates the minimum width between two edge
interrupts in µSOFs (1 µSOF = 125 µs). This is not valid for level
interrupts. A count of zero means that interrupts occur as and when an
event occurs.
23 to 16
-
reserved
15 to 0
NO_OF_
CLK[15:0]
Number of Clocks: Count in number of clocks that the edge interrupt
must be kept asserted on the interface. The default IRQ pulse width is
approximately 500 ns.
8.3.10 DMA Start Address register (W: 0344h)
This register defines the start address select for the DMA read and write operations. See
Table 48 for the bit allocation.
Table 48:
DMA Start Address register: bit allocation
Bit
31
30
29
28
27
26
25
24
reserved [1]
Symbol
Reset
0
0
0
0
0
0
0
0
Access
W
W
W
W
W
W
W
W
Bit
23
22
21
20
19
18
17
16
reserved [1]
Symbol
Reset
0
0
0
0
0
0
0
0
Access
W
W
W
W
W
W
W
W
Bit
15
14
13
12
11
10
9
8
Reset
0
0
0
0
0
0
0
0
Access
W
W
W
W
W
W
W
W
Bit
7
6
5
4
3
2
1
0
Reset
0
0
0
0
0
0
0
0
Access
W
W
W
W
W
W
W
W
Symbol
START_ADDR_DMA[15:8]
Symbol
[1]
START_ADDR_DMA[7:0]
The reserved bits should always be written with the reset value.
Table 49:
DMA Start Address register: bit description
Bit
Symbol
Description
31 to 16
-
reserved
15 to 0
START_ADDR
_DMA[15:0]
Start Address for DMA: The start address for DMA read or write
cycles.
8.3.11 Power Down Control register (R/W: 0354h)
This register is used to turn off power to the internal blocks of the ISP1760 to obtain
maximum power savings. Table 50 shows the bit allocation of the register.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
46 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 50:
Power Down Control register: bit allocation
Bit
31
30
29
28
Symbol
Reset
Access
Bit
Access
Bit
Access
Bit
Access
[1]
24
0
0
0
0
0
0
1
1
R/W
R/W
R/W
R/W
R/W
R/W
R/W
23
22
21
20
19
18
17
16
CLK_OFF_COUNTER[7:0]
1
1
1
0
1
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
15
14
13
12
11
10
9
8
reserved [1]
PORT3_
PD
PORT2_
PD
VBATDET_
PWR
reserved [1]
0
0
0
1
1
0
1
1
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
7
6
5
4
3
2
1
0
BIASEN
VREG_ON
OC3_PWR
OC2_PWR
OC1_PWR
HC_CLK_
EN
reserved [1]
Symbol
Reset
25
R/W
Symbol
Reset
26
CLK_OFF_COUNTER[15:8]
Symbol
Reset
27
1
0
1
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
The reserved bits should always be written with the reset value.
Table 51:
Power Down Control register: bit description
Bit [1]
Symbol
Description
31 to 16
CLK_OFF
_COUNTER
[15:0]
Clock Off Counter: Determines the wake-up status duration after any
wake-up event before the ISP1760 goes back into suspend mode. This
timeout is applicable only if, during the given interval, the Host
Controller is not programmed back to the normal functionality.
03E8h — The default value. It determines the default wake-up interval
of 10 ms. A value of zero implies that the Host Controller never wakes
up on any of the events. This may be useful when using the ISP1760 as
a peripheral to save power by permanently programming the Host
Controller in suspend.
FFFFh — The maximum value. It determines a maximum wake-up time
of 500 ms.
The setting of this register is based on the 100 kHz ± 40 % LazyClock
frequency. It is a multiple of 10 µs period. In 16-bit mode, a write
operation to these bits with any value will determine a fixed wake-up
time of 50 ms.
15 to 13
-
reserved
12
PORT3_
PD
Port 3 Pull-Down: Controls port 3 pull-down resistors.
0 — Port 3 pull-down resistors are connected in suspend
1 — Port 3 pull-down resistors are not connected in suspend.
11
PORT2_
PD
Port 2 Pull-Down: Controls port 2 pull-down resistors.
0 — Port 2 internal pull-down resistors are connected in suspend
1 — Port 2 internal pull-down resistors are not connected in suspend.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
47 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 51:
Power Down Control register: bit description…continued
Bit [1]
Symbol
10
VBATDET_
PWR
Description
VBAT Detector Powered: Controls the power to the VBAT detector.
0 — VBAT detector is powered or enabled in suspend
1 — VBAT detector is not powered or disabled in suspend.
9 to 6
-
reserved; write logic 0
5
BIASEN
BIAS Circuits Powered: Controls the power to internal BIAS circuits.
0 — Internal BIAS circuits are not powered in suspend
1 — Internal BIAS circuits are powered in suspend.
4
VREG_ON
VREG Powered: Enables or disables the internal 3.3 V and 1.8 V
regulators when the ISP1760 is in suspend.
0 — Internal regulators are powered in suspend
1 — Internal regulators are not powered in suspend.
3
OC3_PWR
OC3_N Powered: Controls the powering of the overcurrent detection
circuitry for port 3.
0 — Overcurrent detection is powered on or enabled during suspend.
1 — Overcurrent detection is powered off or disabled during suspend.
This may be useful when connecting a faulty device while the system is
in standby.
2
OC2_PWR
OC2_N Powered: Controls the powering of the overcurrent detection
circuitry for port 2.
0 — Overcurrent detection powered-on or enabled during suspend.
1 — Overcurrent detection powered-off or disabled during suspend.
This may be useful when connecting a faulty device while the system is
in standby.
1
OC1_PWR
OC1_N Powered: Controls the powering of the overcurrent detection
circuitry for port 1.
0 — Overcurrent detection powered-on or enabled during suspend.
1 — Overcurrent detection powered-off or disabled during suspend.
This may be useful when connecting a faulty device while the system is
in standby.
0
HC_CLK_
EN
Host Controller Clock Enabled: Controls internal clocks during
suspend.
0 — Clocks are disabled during suspend. This is the default value. Only
the LazyClock of 100 kHz ± 40 % will be left running in suspend if this
bit is logic 0. If clocks are stopped during suspend, CLKREADY IRQ will
be generated when all clocks are running stable.
1 — All clocks are enabled even in suspend.
[1]
For a 32-bit operation, the default wake-up counter value is 10 µs. For a 16-bit operation, the wake-up
counter value is 50 ms. In the 16-bit operation, read and write back the same value on initialization.
8.3.12 Port 1 Control register (R/W: 0374h)
The values read from the lower 16 bits and the upper 16 bits of this register are always the
same. Table 52 shows the bit allocation of the register.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
48 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 52:
Port 1 Control register: bit allocation
Bit
31
30
29
28
Symbol
Reset
Access
Bit
Symbol
Access
Bit
25
24
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
23
22
21
20
19
18
17
16
reserved [1]
1
0
0
0
0
1
1
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
15
14
13
12
11
10
9
8
reserved [1]
Symbol
Reset
Access
Bit
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
7
6
5
4
3
2
1
0
reserved [1]
PORT1_
INIT1
Reset
Access
[1]
26
R/W
PORT1_
INIT2
Reset
Symbol
27
reserved [1]
reserved [1]
PORT1_POWER[1:0]
0
0
0
1
0
1
1
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
The reserved bits should always be written with the reset value.
Table 53:
Bit [1]
Port 1 Control register: bit description
Symbol
Description
31 to 24 -
reserved; write logic 0
23
PORT1_
INIT2
Port 1 Initialization 2: Write logic 1 at the ISP1760 initialization. It will
clear both this bit and bit 7. Affects only port 1.
22 to 8
-
reserved; write logic 0
7
PORT1_
INIT1
Port 1 Initialization 1: Must be reset to logic 0 at power-up initialization
for correct operation of port 1. Correct Host Controller functionality is not
ensured if set to logic 1 (affects only port 1). To clear this bit, logic 1 must
be written to bit 23 during the ISP1760 initialization.
This is not required for the normal functionality of port 2 and port 3.
6 to 5
-
4 to 3
PORT1_
Port 1 Power: Set these bits to 11b. These bits must be set to enable
POWER[1:0] port 1 power.
2 to 0
-
[1]
reserved
reserved; write logic 0
For correct port 1 initialization, write 0080 0018h to this register after power on.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
49 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
8.4 Interrupt registers
8.4.1 Interrupt register (R/W: 0310h)
The bits of this register indicate the interrupt source, defining the events that determined
the INT generation. Clearing the bits that were set because of the events listed is done by
writing back logic 1 to the respective position. All bits must be reset before enabling new
interrupt events. These bits will be set, regardless of the setting of bit GLOBAL_INTR_EN
in the HW Mode Control register. Table 54 shows the bit allocation of the Interrupt register.
Table 54:
Interrupt register: bit allocation
Bit
31
30
29
28
Symbol
Reset
Access
Bit
25
24
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
23
22
21
20
19
18
17
16
reserved [1]
Reset
Access
Bit
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
15
14
13
12
11
10
9
8
ISO_IRQ
ATL_IRQ
reserved [1]
Symbol
Reset
Access
Bit
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
7
6
5
4
3
2
1
0
HC_SUSP
reserved [1]
INT_IRQ
Reset
Access
[1]
26
0
Symbol
Symbol
27
reserved [1]
CLK
READY
reserved [1]
DMA
EOTINT
SOFITLINT
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
The reserved bits should always be written with the reset value.
Table 55:
Interrupt register: bit description
Bit
Symbol
Description
31 to 10
-
reserved; write logic 0
9
ISO_IRQ
ISO IRQ: Indicates that an IRQ was asserted because an ISO PTD was
completed, or the PTDs corresponding to the bits set in the ISO IRQ
Mask AND or ISO IRQ Mask OR register bits combination were
completed.
0 — No IRQ assertion determined by the completion of ISO PTDs
1 — IRQ asserted because of completing ISO PTDs.
For details, see Section 7.4.
8
ATL_IRQ
ATL IRQ: Indicates that an IRQ was asserted because an ATL PTD was
completed, or the PTDs corresponding to the bits set in the ATL IRQ
Mask AND or ATL IRQ Mask OR register bits combination were
completed.
0 — No IRQ assertion determined by the completion of ATL PTDs
1 — IRQ asserted because of completing ATL PTD.
For details, see Section 7.4.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
50 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 55:
Interrupt register: bit description…continued
Bit
Symbol
Description
7
INT_IRQ
INT IRQ: Indicates that an IRQ was asserted because an INT PTD was
completed, or the PTDs corresponding to the bits set in the INT IRQ
Mask AND or INT IRQ Mask OR register bits combination were
completed.
0 — No IRQ assertion determined by the completion of INT PTDs
1 — IRQ asserted because of completing INT PTD.
For details, see Section 7.4.
6
CLKREADY Clock Ready: Indicates that an IRQ was asserted as the internal clock
signals are running stable. Useful after a power-on or wake-up cycle.
0 — No CLKREADY event has occurred
1 — INT generated because of a CLKREADY event.
5
HC_SUSP
Host Controller Suspend: Indicates that the Host Controller has
entered suspend mode.
0 — No INT generated because of the Host Controller entering suspend
mode
1 — INT generated because of the Host Controller entering suspend
mode.
If the ISR accesses the ISP1760, it will wake up for the time specified in
bits 31 to 16 of the Power Down Control register.
4
-
reserved; write logic 0
3
DMAEOT
INT
DMA EOT Interrupt: Indicates DMA transfer completion.
0 — DMA transfer is not complete
1 — IRQ asserted because the DMA transfer is complete.
2 to 1
-
reserved; write logic 0
0
SOFITLINT SOT ITL Interrupt:
0 — No SOF event has occurred
1 — An SOF event has occurred.
8.4.2 Interrupt Enable register (R/W: 0314h)
This register allows enabling or disabling of the IRQ generation because of various events
as described in Table 56.
Table 56:
Interrupt Enable register: bit allocation
Bit
31
30
29
28
Reset
Access
Bit
Access
26
25
24
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
23
22
21
20
19
18
17
16
reserved [1]
Symbol
Reset
27
reserved [1]
Symbol
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
51 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Bit
15
14
13
Symbol
Reset
Access
Bit
Symbol
11
10
9
8
ISO_IRQ_
E
ATL_IRQ
_E
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
2
1
7
6
5
4
3
INT_IRQ_E
CLK
READY _E
HCSUSP_
E
reserved [1]
DMAEOT
INT _E
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Reset
Access
[1]
12
reserved [1]
reserved [1]
0
SOFITLINT
_E
The reserved bits should always be written with the reset value.
Table 57:
Interrupt Enable register: bit description
Bit
Symbol
Description
31 to 10
-
reserved; write logic 0
9
ISO_IRQ_E
ISO IRQ Enable: Controls the IRQ assertion because of completing
one or more ISO PTDs matching the ISO IRQ Mask AND or
ISO IRQ Mask OR register bits combination.
0 — No IRQ will be asserted because of completing ISO PTDs
1 — IRQ will be asserted.
For details, see Section 7.4.
8
ATL_IRQ_E
ATL IRQ Enable: Controls the IRQ assertion because of completing
one or more ATL PTDs matching the ATL IRQ Mask AND or
ATL IRQ Mask OR register bits combination.
0 — No IRQ will be asserted because of completing ATL PTDs
1 — IRQ will be asserted.
For details, see Section 7.4.
7
INT_IRQ_E
INT IRQ Enable: Controls the IRQ assertion because of completing
one or more INT PTDs matching the INT IRQ Mask AND or
INT IRQ Mask OR register bits combination.
0 — No IRQ will be asserted because of completing INT PTDs
1 — IRQ will be asserted.
For details, see Section 7.4.
6
CLKREADY
_E
Clock Ready Enable: Enables the IRQ assertion when internal clock
signals are running stable. Useful after power-on or wake-up.
0 — No IRQ will be generated after a CLKREADY_E event has
occurred
1 — IRQ will be generated after a CLKREADY_E event.
5
HCSUSP_E Host Controller Suspend Enable: Enables the IRQ generation when
the Host Controller enters suspend mode.
0 — No IRQ will be generated because of the Host Controller entering
suspend mode
1 — IRQ will be generated at the Host Controller entering suspend
mode.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
52 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 57:
Interrupt Enable register: bit description…continued
Bit
Symbol
Description
4
-
reserved; write logic 0
3
DMAEOT
INT_E
DMA EOT Interrupt Enable: Controls assertion of IRQ on the DMA
transfer completion.
0 — No IRQ will be generated after the DMA transfer is completed
1 — IRQ will be asserted because of the DMA transfer completion.
2 to 1
-
reserved; must be written with logic 0
0
SOFITLINT
_E
SOT ITL Interrupt Enable: Controls the IRQ generation at every SOF
occurrence.
0 — No IRQ will be generated on an SOF occurrence
1 — IRQ will be asserted at every SOF.
8.4.3 ISO IRQ Mask OR register (R/W: 0318h)
Each bit of this register corresponds to one of the 32 ISO PTDs defined, and is a
hardware IRQ mask for each PTD done map. See Table 58 for bit description. For details,
see Section 7.4.
Table 58:
Bit
ISO IRQ Mask OR register: bit description
Symbol
31 to 0 ISO_IRQ_
MASK_OR
[31:0]
Access Value
Description
R/W
ISO IRQ Mask OR: Represents a direct map for
ISO PTDs 31 to 0.
0000 0000h
0 — No OR condition defined between ISO PTDs
1 — The bits corresponding to certain PTDs are set
to logic 1 to define a certain OR condition.
8.4.4 INT IRQ Mask OR register (R/W: 031Ch)
Each bit of this register (see Table 59) corresponds to one of the 32 INT PTDs defined,
and is a hardware IRQ mask for each PTD done map. For details, see Section 7.4.
Table 59:
Bit
INT IRQ Mask OR register: bit description
Symbol
Access Value
31 to 0 INT_IRQ_ R/W
MASK_OR
[31:0]
0000 0000h
Description
INT IRQ Mask OR: Represents a direct map for
INT PTDs 31 to 0.
0 — No OR condition defined between INT PTDs
31 to 0
1 — The bits corresponding to certain PTDs are
set to logic 1 to define a certain OR condition.
8.4.5 ATL IRQ Mask OR register (R/W: 0320h)
Each bit of this register corresponds to one of the 32 ATL PTDs defined, and is a
hardware IRQ mask for each PTD done map. See Table 60 for bit description. For details,
see Section 7.4.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
53 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 60:
Bit
ATL IRQ Mask OR register: bit description
Symbol
Access Value
31 to 0 ATL_IRQ_ R/W
MASK_OR
[31:0]
Description
0000 0000h ATL IRQ Mask OR: Represents a direct map for ATL
PTDs 31 to 0.
0 — No OR condition defined between the ATL
PTDs
1 — The bits corresponding to certain PTDs are set
to logic 1 to define a certain OR condition.
8.4.6 ISO IRQ Mask AND register (R/W: 0324h)
Each bit of this register corresponds to one of the 32 ISO PTDs defined, and is a
hardware IRQ mask for each PTD done map. For details, see Section 7.4.
Table 61 provides the bit description of the register.
Table 61:
Bit
ISO IRQ Mask AND register: bit description
Symbol
Access
31 to 0 ISO_IRQ_ R/W
MASK_
AND[31:0]
Value
Description
0000 0000h
ISO IRQ Mask AND: Represents a direct map for
ISO PTDs 31 to 0.
0 — No AND condition defined between ISO PTDs
1 — The bits corresponding to certain PTDs are set
to logic 1 to define a certain AND condition
between the 32 INT PTDs.
8.4.7 INT IRQ Mask AND register (R/W: 0328h)
Each bit of this register (see Table 62) corresponds to one of the 32 INT PTDs defined,
and is a hardware IRQ mask for each PTD done map. For details, see Section 7.4.
Table 62:
Bit
INT IRQ Mask AND register: bit description
Symbol
Access Value
31 to 0 INT_IRQ_ R/W
MASK_
AND[31:0]
Description
0000 0000h INT IRQ Mask AND: Represents a direct map for
INT PTDs 31 to 0.
0 — No OR condition defined between INT PTDs
1 — The bits corresponding to certain PTDs are set
to logic 1 to define a certain AND condition between
the 32 INT PTDs.
8.4.8 ATL IRQ Mask AND register (R/W: 032Ch)
Each bit of this register corresponds to one of the 32 ATL PTDs defined, and is a
hardware IRQ mask for each PTD done map. For details, see Section 7.4.
Table 63 shows the bit description of the register.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
54 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 63:
Bit
ATL IRQ Mask AND register: bit description
Symbol
Access Value
31 to 0 ATL_IRQ_ R/W
MASK_
AND[31:0]
Description
0000 0000h ATL IRQ Mask AND: Represents a direct map for
ATL PTDs 31 to 0.
0 — No OR condition defined between ATL PTDs
1 — The bits corresponding to certain PTDs are set
to logic 1 to define a certain AND condition between
the 32 ATL PTDs.
9. Philips Transfer Descriptor
The standard EHCI data structures as described in Enhanced Host Controller Interface
Specification for Universal Serial Bus Rev. 1.0 are optimized for the bus master operation
that is managed by the hardware state machine.
The PTD structures of the ISP1760 are translations of the EHCI data structures that are
optimized for the ISP1760, while keeping the architecture of the EHCI data structures the
same. This is because the ISP1760 is a slave Host Controller and has no bus master
capability.
EHCI manages schedules in two lists: periodic and asynchronous. The data structures
are designed to provide the maximum flexibility required by USB, minimize memory traffic,
and hardware and software complexity. The ISP1760 controller executes transactions for
devices by using a simple shared-memory schedule. This schedule consists of data
structures organized into three lists.
qISO — Isochronous transfer
qINTL — Interrupt transfer
qATL — Asynchronous transfer; for the control and bulk transfers.
The system software maintains two lists for the Host Controller: periodic and
asynchronous. The root of the periodic schedule—the PERIODICLISTBASE register—is
the physical memory base address of the periodic frame list. The periodic frame list is an
array memory pointer. The objects referenced from the frame list must be valid schedule
data structures. The asynchronous list base is also a common list of queue heads
(endpoints) that are served in a schedule. These endpoint data structures are further
linked to the EHCI transfer descriptor that is the valid schedule (queue PTD).
The Periodic Schedule Enable (ISO_BUF_FULL and INT_BUF_FULL) or Asynchronous
Schedule Enable (ATL_BUF_FULL) bits can enable traversal to these lists. Enabling a list
indicates the presence of valid schedule in the list. The system software starts at these
points, schedules the first transfer inside the shared memory of the ISP1760, and sets up
the ATL, INTL or ITL bit corresponding to the type of transfer scheduled in the shared
memory.
The ISP1760 has a maximum of 32 ISO, 32 INTL and 32 ATL PTDs. These PTDs are
used as channels to transfer data from the shared memory to the USB bus. These
channels are allocated and deallocated on receiving the transfer from the core USB driver.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
55 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Multiple transfers are scheduled to the shared memory for various endpoints by traversing
the next link pointer provided by the EHCI data structure, until it reaches the terminate bit
in a microframe. If a schedule is enabled, the Host Controller starts executing from the
ISO schedule, before it goes to the INTL schedule, and then to the ATL schedule.
The EHCI periodic and asynchronous lists are traversed by the software according to the
EHCI traversal rule, and executed only from the asynchronous schedule after it
encounters the end of the periodic schedule. The Host Controller traverses the ISO, INTL
and ATL schedules. It fetches the element and begins traversing the graph of linked
schedule data structures.
The last bit identifies the end of the schedule for each type of transfer, indicating the rest
of the channels are empty. Once a transition is completed, the Host Controller executes
from the next transfer descriptor in the schedule until the end of the microframe.
The completion of a transfer is indicated to the software by the interrupt that can be
grouped over the various PTDs by using the AND or OR registers that are available for
each schedule type (ISO, INTL and ATL). These registers are simple logic registers to
decide the group and individual PTDs that can interrupt the CPU for a schedule, when the
logical conditions of the done bit is true in the shared memory that completes the interrupt.
Interrupts are of four types and the latency can be programmed in multiples of µSOF
(125 µs).
•
•
•
•
ISO interrupt
INTL interrupt
ATL Interrupt
SOF—start of frame interrupt for the data transfer.
A static PTD that schedules inside the ISP1760 shared memory allows using the
NextPTD mechanism that will enable the Host Controller driver to schedule the multiple
PTDs that are of single endpoint and reduce the interrupt to the CPU.
The NextPTD traversal rules defined by the ISP1760 hardware are:
1. Start the ATL header traversal.
2. If the current PTD is active and not done, perform the transaction.
3. Follow the next link pointer.
4. If PTD is not active and done, jump to the next PTD.
5. If the next link pointer is NULL, it means the end of the traversal.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
56 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
START PTD
SCHEDULE
follow the next link pointer
no
follow the next link pointer
PTD DONE?
yes
INCREMENT
THE PTD
horizontal
link pointer
vertical
link pointer
EXECUTE
THE PTD
EXECUTE
THE PTD
null pointer(1)
END THE
SCHEDULE
END THE
SCHEDULE
004aaa585
(1) The NULL pointer terminates goes to the next link.
Fig 10. NextPTD traversal rule.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
57 of 105
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx
xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Table 64:
Bit
High-speed bulk IN and OUT, QHA: bit allocation
63
62
61
60
59
58
57
56 55
54
53
52
51
50
49
DW7
H
B
X
[1]
P
D
T
Cerr
[1:0]
NakCnt[3:0]
45
44
43
42
41
40
39
38
37
36
35
34
33
32
NrBytesTransferred[14:0] (32 kbytes for high-speed)
30
29
28
27
26
25
24
23
22
S
21
20
19
18
DW6
17
16
15
14
EP
Type
[1:0]
13
12
Token
[1:0]
11
10
DeviceAddress[6:0]
9
8
7
6
5
4
EndPt[3:0]
31 to 34
3
2
1
0
reserved
DW4
Rev. 01 — 8 November 2004
DW0
46
reserved
reserved
31
DW2
47
reserved
A
DW1
Bit
48
reserved
DW5
DW3
Philips Semiconductors
9397 750 13257
Product data sheet
9.1 High-speed bulk IN and OUT, Queue Head Asynchronous (QHA) (patent-pending)
reserved
reserved
[2]
[1]
Reserved.
[2]
EndPt[0].
Mult
[1:0]
RL[3:0]
[1]
MaxPacketLength[10:0]
J
DataStartAddress[15:0]
NrBytesToTransfer[14:0] (32 kbytes for high-speed)
NextPTDPointer[4:0]
reserved
[1]
V
ISP1760
Embedded Hi-Speed USB host controller
58 of 105
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 65:
High-speed bulk IN and OUT, QHA: bit description
Bit
Symbol
Access
Description
reserved
-
-
reserved
-
-
reserved
-
-
31 to 6
reserved
-
0; not applicable for QHA.
5
J
SW — writes
Jump:
DW7
63 to 32
DW6
31 to 0
DW5
63 to 32
DW4
0 — To increment the PTD pointer
1 — To enable the next PTD branching.
4 to 0
NextPTDPointer
[4:0]
SW — writes
Next PTD Counter: Next PTD branching assigned by the PTD pointer.
A
SW — sets
Active: Write the same value as that in V.
DW3
63
HW — resets
62
H
HW — writes
Halt: This bit correspond to the Halt bit of the Status field of QH.
61
B
HW — writes
Babble: This bit correspond to the Babble Detected bit in the Status
field of the iTD, SiTD or QH.
1 — When babbling is detected, A and V are set to 0.
60
X
HW — writes
Error: This bit corresponds to the Transaction Error bit in the Status
field of iTD, SiTD or QH (Exec_Trans, the signal name is xacterr).
0 — No PID error.
1 — If there are PID errors, this bit is set active. The A and V bits are
also set to inactive. This transaction is retried three times.
59
reserved
-
-
58
P
HW — writes
Ping: For high-speed transactions, this bit corresponds to the Ping
state bit in the Status field of a QH.
0 — Ping is not set.
1 — Ping is set.
Software sets this bit to 0.
57
DT
HW — updates
SW — writes
56 to 55
Cerr[1:0]
HW — writes
SW — writes
Data Toggle: This bit is filled by software to start a PTD. If
NrBytesToTransfer[14:0] is not complete, software needs to read this
value and then write back the same value to continue.
Error Counter. This field corresponds to the Cerr[1:0] field in QH. The
default value of this field is zero for isochronous transactions.
00 — The transaction will not retry.
11 — The transaction will retry three times. Hardware will decrement
these values. When the transaction has tried three times, X error will
be updated.
54 to 51
50 to 47
NakCnt[3:0]
reserved
HW — writes
SW — writes
NAK Counter. This field corresponds to the NAKCnt field in QH.
Software writes for the initial PTD launch. The V bit is reset if NakCnt
decrements to zero and RL is a non-zero value. It reloads from RL if
transaction is ACKed.
-
-
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
59 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 65:
High-speed bulk IN and OUT, QHA: bit description…continued
Bit
Symbol
46 to 32
NrBytesTransferred HW — writes
[14:0]
SW — writes
0000
Access
Number of Bytes Transferred: This field indicates the number of
bytes sent or received for this transaction. If Mult[1:0] is greater than
one, it is possible to store intermediate results in this field.
Description
31 to 29
reserved
-
Set to 0 for QHA.
28 to 25
RL[3:0]
SW — writes
Reload: If RL is set to 0h, hardware ignores the NakCnt value. RL and
NakCnt are set to the same value before a transaction.
24
reserved
-
Always 0 for QHA.
23 to 8
DataStartAddress
[15:0]
SW — writes
Data Start Address: This is the start address for the data that will be
sent or received on or from the USB bus. This is the internal memory
address and not the direct CPU address.
DW2
RAM address = (CPU address − 400h)/8
7 to 0
reserved
-
-
63 to 47
reserved
-
Always 0 for QHA.
46
S
SW — writes
This bit indicates whether a split transaction has to be executed:
DW1
0 — High-speed transaction
1 — Split transaction.
45 to 44
EPType[1:0]
SW — writes
Transaction type:
00 — Control
10 — Bulk.
43 to 42
Token[1:0]
SW — writes
Token: Identifies the token Packet Identifier (PID) for this transaction:
00 — OUT
01 — IN
10 — SETUP
11 — PING (written by hardware only).
41 to 35
DeviceAddress[6:0] SW — writes
Device Address: This is the USB address of the function containing
the endpoint that is referred to by this buffer.
34 to 32
EndPt[3:1]
SW — writes
Endpoint: This is the USB address of the endpoint within the function.
31
EndPt[0]
SW — writes
Endpoint: This is the USB address of the endpoint within the function.
30 to 29
Mult[1:0]
SW — writes
Multiplier: This field is a multiplier used by the Host Controller as the
number of successive packets the Host Controller may submit to the
endpoint in the current execution.
DW0
For QHA, this is a copy of the Async Schedule Park mode count, if the
Async Schedule Park mode is enabled. These EHCI registers need to
be set to reflect multiple cycles. Applicable for high-speed only.
Set this field to 01b. You can also set it to 11b and 10b depending on
your application. 00b is undefined.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
60 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 65:
High-speed bulk IN and OUT, QHA: bit description…continued
Bit
Symbol
Access
Description
28 to 18
MaxPacketLength
[10:0]
SW — writes
Maximum Packet Length: This field indicates the maximum number
of bytes that can be sent to or received from an endpoint in a single
data packet. The maximum packet size for a bulk transfer is 512 bytes.
The maximum packet size for the isochronous transfer is also variable
at any whole number.
17 to 3
NrBytesToTransfer
[14:0]
SW — writes
Number of Bytes to Transfer: This field indicates the number of bytes
that can be transferred by this data structure. It is used to indicate the
depth of the DATA field (32 kbytes).
2 to 1
reserved
-
-
0
V
SW — sets
Valid:
HW — resets
0 — This bit is deactivated when the entire PTD is executed—across
µSOF and SOF—or when a fatal error is encountered.
1 — Software updates to one when there is payload to be sent or
received even across ms boundary. The current PTD is active.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
61 of 105
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx
xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Table 66:
Bit
High-speed isochronous IN and OUT, iTD: bit allocation
63
62
61
60
DW7
59
58
57
DW4
H
52
51
50
49
48
47
30
29
28
27
26
Status6[2:0]
Rev. 01 — 8 November 2004
[1]
Reserved.
[2]
EndPt[0].
Mult
[1:0]
44
43
42
41
40
25
39
38
37
24
23
22
20
Status4[2:0]
19
18
17
16
15
14
EP
Type
[1:0]
13
12
Token
[1:0]
11
10
DeviceAddress[6:0]
9
8
7
6
5
4
ISOIN_3[11:0]
Status3[2:0]
Status2[2:0]
Status1[2:0]
DataStartAddress[15:0]
MaxPacketLength[10:0]
34
33
32
ISOIN_0[11:0]
ISOIN_4[11:0]
Status5[2:0]
35
NrBytesTransferred[14:0] (32 kbytes for high-speed)
S
21
36
ISOIN_5[7:0]
ISOIN_1[11:0]
reserved
[2]
45
reserved
ISOIN_5[3:0]
Status7[2:0]
46
ISOIN_6[11:0]
B
DW2
DW0
53
reserved
31
DW6
54
ISOIN_2[7:0]
A
DW1
Bit
56 55
ISOIN_7[11:0]
DW5
DW3
Philips Semiconductors
9397 750 13257
Product data sheet
9.2 High-speed isochronous IN and OUT, isochronous Transfer Descriptor (iTD) (patent-pending)
EndPt[3:0]
34 to 31
3
2
1
0
ISOIN_2[3:0]
µSA[7:0]
Status0[2:0]
µFrame[7:0]
NrBytesToTransfer[14:0] (32 kbytes for high-speed)
[1]
V
ISP1760
Embedded Hi-Speed USB host controller
62 of 105
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 67:
High-speed isochronous IN and OUT, iTD: bit description
Bit
Symbol
Access
Description
63 to 52
ISOIN_7[11:0]
HW — writes
Bytes received during µSOF7, if µSA[7] is set to 1 and frame number
is correct.
51 to 40
ISOIN_6[11:0]
HW — writes
Bytes received during µSOF6, if µSA[6] is set to 1 and frame number
is correct.
39 to 32
ISOIN_5[7:0]
HW — writes
Bytes received during µSOF5 (bits 11 to 4), if µSA[5] is set to 1 and
frame number is correct.
31 to 28
ISOIN_5[3:0]
HW — writes
Bytes received during µSOF5 (bits 3 to 0), if µSA[5] is set to 1 and
frame number is correct.
27 to 16
ISOIN_4[11:0]
HW — writes
Bytes received during µSOF4, if µSA[4] is set to 1 and frame number
is correct.
15 to 4
ISOIN_3[11:0]
HW — writes
Bytes received during µSOF3, if µSA[3] is set to 1 and frame number
is correct.
3 to 0
ISOIN_2[3:0]
HW — writes
Bytes received during µSOF2 (bits 11 to 8), if µSA[2] is set to 1 and
frame number is correct.
63 to 56
ISOIN_2[7:0]
HW — writes
Bytes received during µSOF2 (bits 7 to 0), if µSA[2] is set to 1 and
frame number is correct.
55 to 44
ISOIN_1[11:0]
HW — writes
Bytes received during µSOF1, if µSA[1] is set to 1 and frame number
is correct.
43 to 32
ISOIN_0[11:0]
HW — writes
Bytes received during µSOF0, if µSA[0] is set to 1 and frame number
is correct.
31 to 29
Status7[2:0]
HW — writes
ISO IN or OUT status at µSOF7
28 to 26
Status6[2:0]
HW — writes
ISO IN or OUT status at µSOF6
25 to 23
Status5[2:0]
HW — writes
ISO IN or OUT status at µSOF5
22 to 20
Status4[2:0]
HW — writes
ISO IN or OUT status at µSOF4
19 to 17
Status3[2:0]
HW — writes
ISO IN or OUT status at µSOF3
16 to 14
Status2[2:0]
HW — writes
ISO IN or OUT status at µSOF2
13 to 11
Status1[2:0]
HW — writes
ISO IN or OUT status at µSOF1
10 to 8
Status0[2:0]
HW — writes
Status of the payload on the USB bus for this µSOF after ISO has
been delivered.
DW7
DW6
DW5
DW4
Bit 0 — Transaction Error (IN and OUT)
Bit 1 — Babble (IN token only)
Bit 2 — underrun (OUT token only).
7 to 0
µSA[7:0]
SW — writes
(0 => 1)
HW — writes
(1 => 0)
After processing
µSOF Active: When the frame number of bits DW1[7:3] match the
frame number of USB bus, these bits are checked for 1 before they are
sent for µSOF. For example: If µSA[7:0] = 1, 1, 1, 1, 1, 1, 1, 1: send
ISO every µSOF of the entire ms. If µSA[7:0] = 0, 1, 0, 1, 0, 1, 0, 1:
send ISO only on µSOF0, µSOF2, µSOF4 and µSOF6.
DW3
63
A
SW — sets
Active: This bit is the same as the Valid bit.
62
H
HW — writes
Halt: Only one bit for the entire ms. When this bit is set, the Valid bit is
reset. The device decides to stall an endpoint.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
63 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 67:
High-speed isochronous IN and OUT, iTD: bit description…continued
Bit
Symbol
Access
Description
61
B
HW — writes
Babble: Not applicable here.
60 to 47
reserved
-
Set to 0 for isochronous.
46 to 32
NrBytesTransferred HW — writes
[14:0]
Number of Bytes Transferred: This field indicates the number of
bytes sent or received for this transaction. If Mult[1:0] is greater than
one, it is possible to store intermediate results in this field.
NrBytesTransferred[14:0] is 32 kbytes per PTD.
31 to 24
reserved
-
Set to 0 for isochronous.
23 to 8
DataStartAddress
[15:0]
SW — writes
Data Start Address: This is the start address for the data that will be
sent or received on or from the USB bus. This is the internal memory
address and not the direct CPU address.
DW2
RAM address = (CPU address − 400h)/8
7 to 0
µFrame[7:0]
SW — writes
Bits 2 to 0 — Don’t care
Bits 7 to 3 — Frame number that this PTD will be sent for ISO OUT or
IN.
DW1
63 to 47
reserved
-
-
46
S
SW — writes
This bit indicates whether a split transaction has to be executed.
0 — High-speed transaction
1 — Split transaction.
45 to 44
EPType[1:0]
SW — writes
Endpoint type:
01 — Isochronous.
43 to 42
Token[1:0]
SW — writes
Token: This field indicates the token PID for this transaction:
00 — OUT
01 — IN.
41 to 35
DeviceAddress[6:0] SW — writes
Device Address: This is the USB address of the function containing
the endpoint that is referred to by this buffer.
34 to 32
EndPt[3:1]
SW — writes
Endpoint: This is the USB address of the endpoint within the function.
31
EndPt[0]
SW — writes
Endpoint: This is the USB address of the endpoint within the function.
30 to 29
Mult[1:0]
SW — writes
This field is a multiplier counter used by the Host Controller as the
number of successive packets the Host Controller may submit to the
endpoint in the current execution.
DW0
For isochronous OUT and IN:
If Mult[1:0] is 01 — Data Toggle is Data0
If Mult[1:0] is 10 — Data Toggle is Data1
If Mult[1:0] is 11 — Data Toggle is Data2, and so on.
For details, refer to Enhanced Host Controller Interface Specification
for Universal Serial Bus Rev. 1.0 Appendix D.
28 to 18
MaxPacketLength
[10:0]
SW — writes
Maximum Packet Length: This field indicates the maximum number
of bytes that can be sent to or received from the endpoint in a single
data packet. The maximum packet size for an isochronous transfer is
1024 bytes. The maximum packet size for the isochronous transfer is
also variable at any whole number.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
64 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 67:
High-speed isochronous IN and OUT, iTD: bit description…continued
Bit
Symbol
Access
Description
17 to 3
NrBytesToTransfer
[14:0]
SW — writes
Number of Bytes Transferred: This field indicates the number of
bytes that can be transferred by this data structure. It is used to
indicate the depth of the DATA field (32 kbytes).
2 to 1
reserved
-
-
0
V
HW — resets
0 — This bit is deactivated when the entire PTD is executed—across
µSOF and SOF—or when a fatal error is encountered.
SW — sets
1 — Software updates to one when there is payload to be sent or
received even across ms boundary. The current PTD is active.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
65 of 105
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx
xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Table 68:
Bit
High-speed interrupt IN and OUT, QHP: bit allocation
63
62
61
60
DW7
59
58
57
DW4
H
reserved
30
29
52
51
50
49
48
47
28
27
26
Status7[2:0]
Status6[2:0]
Rev. 01 — 8 November 2004
[1]
Reserved.
[2]
EndPt[0].
Mult
[1:0]
45
44
43
42
41
40
25
39
38
INT_IN_6[11:0]
Cerr
[1:0]
24
23
22
20
19
18
17
16
15
14
EP
Type
[1:0]
13
INT_IN_4[11:0]
Status5[2:0]
Status4[2:0]
35
34
33
32
INT_IN_5[7:0]
12
Token
[1:0]
11
10
DeviceAddress[6:0]
9
8
7
6
5
4
INT_IN_3[11:0]
Status3[2:0]
Status2[2:0]
Status1[2:0]
DataStartAddress[15:0]
MaxPacketLength[10:0]
36
NrBytesTransferred[14:0] (32 kbytes for high-speed)
S
21
37
INT_IN_0[11:0]
reserved
reserved
[2]
46
INT_IN_1[11:0]
D
T
INT_IN_5[3:0]
DW2
DW0
53
reserved
31
DW6
54
INT_IN_2[7:0]
A
DW1
Bit
56 55
INT_IN_7[11:0]
DW5
DW3
Philips Semiconductors
9397 750 13257
Product data sheet
9.3 High-speed interrupt IN and OUT, Queue Head Periodic (QHP) (patent-pending)
EndPt[3:0]
31 to 34
3
2
1
0
INT_IN_2[3:0]
µSA[7:0]
Status0[2:0]
µFrame[7:0]
NrBytesToTransfer[14:0] (32 kbytes for high-speed)
[1]
V
ISP1760
Embedded Hi-Speed USB host controller
66 of 105
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 69:
Bit
High-speed interrupt IN and OUT, QHP: bit description
Symbol
Access
Description
63 to 52
INT_IN_7[[11:0]
HW — writes
Bytes received during µSOF7, if µSA[7] is set to 1 and frame number is
correct.
51 to 40
INT_IN_6[11:0]
HW — writes
Bytes received during µSOF6, if µSA[6] is set to 1 and frame number is
correct.
39 to 32
INT_IN_5[7:0]
HW — writes
Bytes received during µSOF5 (bits 7 to 0), if µSA[5] is set to 1 and frame
number is correct.
31 to 28
INT_IN_5[3:0]
HW — writes
Bytes received during µSOF5 (bits 3 to 0), if µSA[5] is set to 1 and frame
number is correct.
27 to 16
INT_IN_4[11:0]
HW — writes
Bytes received during µSOF4, if µSA[4] is set to 1 and frame number is
correct.
15 to 4
INT_IN_3[11:0]
HW — writes
Bytes received during µSOF3, if µSA[3] is set to 1 and frame number is
correct.
3 to 0
INT_IN_2[3:0]
HW — writes
Bytes received during µSOF2 (bits 11 to 8), if µSA[2] is set to 1 and frame
number is correct.
63 to 56
INT_IN_2[7:0]
HW — writes
Bytes received during µSOF2 (bits 7 to 0), if µSA[2] is set to 1 and frame
number is correct.
55 to 44
INT_IN_1[11:0]
HW — writes
Bytes received during µSOF1, if µSA[1] is set to 1 and frame number is
correct.
43 to 32
INT_IN_0[11:0]
HW — writes
Bytes received during µSOF0, if µSA[0] is set to 1 and frame number is
correct.
DW7
DW6
DW5
DW4
INT OUT or IN
31 to 29
Status7[2:0]
HW — writes
INT IN or OUT status of µSOF7
28 to 26
Status6[2:0]
HW — writes
INT IN or OUT status of µSOF6
25 to 23
Status5[2:0]
HW — writes
INT IN or OUT status of µSOF5
22 to 20
Status4[2:0]
HW — writes
INT IN or OUT status of µSOF4
19 to 17
Status3[2:0]
HW — writes
INT IN or OUT status of µSOF3
16 to 14
Status2[2:0]
HW — writes
INT IN or OUT status of µSOF2
13 to 11
Status1[2:0]
HW — writes
INT IN or OUT status of µSOF1
10 to 8
Status0[2:0]
HW — writes
Status of the payload on the USB bus for this µSOF after INT has been
delivered.
Bit 0 — Transaction Error (IN and OUT)
Bit 1 — Babble (IN token only)
Bit 2 — underrun (OUT token only).
7 to 0
µSA[7:0]
SW — writes
(0 => 1)
A
HW — writes
When the frame number of bits DW1[7:3] match the frame number of the
USB bus, these bits are checked for 1 before they are sent for µSOF. For
example: When µSA[7:0] = 1, 1, 1, 1, 1, 1, 1, 1: send INT for every µSOF of
HW — writes
the entire ms. When µSA[7:0] = 0, 1, 0, 1, 0, 1, 0, 1: send INT for µSOF0,
(1 => 0)
µSOF2, µSOF4 and µSOF6. When µSA[7:0] = 1, 0, 0, 0, 1, 0, 0, 0 = send
After processing
INT for every fourth µSOF.
DW3
63
Active: Write the same value as that in V.
SW — writes
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
67 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 69:
High-speed interrupt IN and OUT, QHP: bit description…continued
Bit
Symbol
Access
Description
62
H
HW — writes
Halt: Transaction is halted.
61 to 58
reserved
-
-
57
DT
HW — writes
Data Toggle: Set the Data Toggle bit to start the PTD. Software writes the
current transaction toggle value. Hardware writes the next transaction toggle
value.
SW — writes
56 to 55
Cerr[1:0]
HW — writes
SW — writes
Error Counter. This field corresponds to the Cerr[1:0] field in the QH. The
default value of this field is zero for isochronous transactions.
54 to 47
reserved
-
-
46 to 32
NrBytes
Transferred
[14:0]
HW — writes
Number of Bytes Transferred: This field indicates the number of bytes sent
or received for this transaction. If Mult[1:0] is greater than one, it is possible
to store intermediate results in this field.
31 to 24
reserved
-
-
23 to 8
DataStart
Address
[15:0]
SW — writes
Data Start Address: This is the start address for the data that will be sent or
received on or from the USB bus. This is the internal memory address and
not the direct CPU address.
DW2
RAM address = (CPU address − 400h)/8
7 to 0
µFrame[7:0]
SW — writes
Bits 7 to 3 represent the polling rate for ms-based polling.
The INT polling rate is defined as 2(b – 1) µSOF, where b is 1 to 9.
When b is 1, 2, 3 or 4, use µSA to define polling because the rate is equal to
or less than 1 ms. Bits 7 to 3 are set to 0. Polling checks µSA bits for µSOF
rates.
b
rate
µFrame[7:3]
µSA[7:0]
1
1 µSOF
0
11111111
2
2 µSOF
0
10101010 or 01010101
3
4 µSOF
0
any 2 bits set
4
1 ms
0
any 1 bit set
5
2 ms
1
any 1 bit set
6
4 ms
10 to 11
any 1 bit set
7
8 ms
100 to 111
any 1 bit set
8
16 ms
1000 to 1111
any 1 bit set
9
32 ms
10000 to 11111
any 1 bit set
DW1
63 to 47
reserved
-
-
46
S
SW — writes
This bit indicates if a split transaction has to be executed:
0 — High-speed transaction
1 — Split transaction.
45 to 44
EPType[1:0]
SW — writes
Endpoint type:
11 — Interrupt.
43 to 42
Token[1:0]
SW — writes
Token: This field indicates the token PID for this transaction:
00 — OUT
01 — IN.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
68 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 69:
High-speed interrupt IN and OUT, QHP: bit description…continued
Bit
Symbol
Access
Description
41 to 35
DeviceAddress
[6:0]
SW — writes
Device Address: This is the USB address of the function containing the
endpoint that is referred to by the buffer.
34 to 32
EndPt[3:1]
SW — writes
Endpoint: This is the USB address of the endpoint within the function.
31
EndPt[0]
SW — writes
Endpoint: This is the USB address of the endpoint within the function.
30 to 29
Mult[1:0]
SW — writes
Multiplier: This field is a multiplier counter used by the Host Controller as
the number of successive packets the Host Controller may submit to the
endpoint in the current execution.
DW0
Set this field to 01b. You can also set it to 11b and 10b depending on your
application. 00b is undefined.
28 to 18
MaxPacket
Length[10:0]
SW — writes
Maximum Packet Length: This field indicates the maximum number of
bytes that can be sent to or received from the endpoint in a single data
packet.
17 to 3
NrBytesTo
Transfer[14:0]
SW — writes
Number of Bytes to Transfer: This field indicates the number of bytes can
be transferred by this data structure. It is used to indicate the depth of the
DATA field (32 kbytes).
2 to 1
reserved
-
-
0
V
SW — sets
Valid:
HW — resets
0 — This bit is deactivated when the entire PTD is executed—across µSOF
and SOF—or when a fatal error is encountered.
1 — Software updates to one when there is payload to be sent or received
even across ms boundary. The current PTD is active.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
69 of 105
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx
xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Table 70:
Bit
Start and complete split for bulk, QHASS/SC: bit allocation
63
62
61
60
59
58
57
56 55
54
53
52
51
50
49
DW7
A
H
B
X
[1]
S
C
D
T
Cerr
[1:0]
HubAddress[6:0]
31
30
29
28
27
26
NakCnt[3:0]
PortNumber[6:0]
25
24
23
22
21
45
44
43
42
41
40
39
38
37
36
35
34
33
32
20
19
18
NrBytesTransferred[14:0]
SE[1:0]
[1]
S
17
15
14
16
EP
Type
[1:0]
13
12
Token
[1:0]
11
10
DeviceAddress[6:0]
9
8
7
6
EndPt[3:0]
(31 to 34)
Rev. 01 — 8 November 2004
5
4
3
2
1
0
J
NextPTDAddress[4:0]
reserved
DW4
DW0
46
reserved
DW6
DW2
47
reserved
DW1
Bit
48
reserved
DW5
DW3
Philips Semiconductors
9397 750 13257
Product data sheet
9.4 Start and complete split for bulk, Queue Head Asynchronous Start Split and Start Complete
(QHA-SS/SC) (patent-pending)
reserved
reserved
[2]
[1]
Reserved.
[2]
EndPt[0].
[1]
RL[3:0]
[1]
MaxPacketLength[10:0]
DataStartAddress[15:0]
NrBytesToTransfer[14:0] (32 kbytes for high-speed)
reserved
[1]
V
ISP1760
Embedded Hi-Speed USB host controller
70 of 105
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 71:
Start and complete split for bulk, QHASS/SC: bit description
Bit
Symbol
Access
Description
reserved
-
-
reserved
-
-
reserved
-
-
31 to 6
reserved
-
-
5
J
SW — writes
0 — To increment the PTD pointer
DW7
63 to 32
DW6
31 to 0
DW5
63 to 32
DW4
1 — To enable the next PTD branching.
4 to 0
NextPTDPointer
[1:0]
SW — writes
Next PTD branching assigned by the PTD pointer.
A
SW — sets
Active: Write the same value as that in V.
DW3
63
HW — resets
62
H
HW — writes
Halt: This bit correspond to the Halt bit of the Status field of QH.
61
B
HW — writes
Babble: This bit correspond to the Babble Detected bit in the Status
field of the iTD, SiTD or QH.
60
X
59
SC
1 — when babbling is detected, A and V are set to 0.
Transaction Error: This bit corresponds to the Transaction Error bit in
the status field.
SW — writes 0
Start/Complete:
HW — updates
0 — Start split
1 — Complete split.
58
reserved
-
-
57
DT
HW — writes
Data Toggle: Set the Data Toggle bit to start for the PTD.
SW — writes
56 to 55
Cerr[1:0]
HW — updates
SW — writes
Error Counter: This field contains the error count for start and complete
split (QHASS). When an error has no response or bad response,
Cerr[1:0] will be decremented to zero and then Valid will be set to zero.
A NAK or NYET will reset Cerr[1:0]. For details, refer to Enhanced Host
Controller Interface Specification for Universal Serial Bus Rev. 1.0
Section 4.12.1.2.
If retry has insufficient time at the beginning of a new SOF, the first PTD
must be this retry. This can be accomplished by if aperiodic PTD is not
advanced.
54 to 51
NakCnt[3:0]
HW — writes
SW — writes
NAK Counter. The V bit is reset if NakCnt decrements to zero and RL
is a non-zero value. Not applicable to isochronous split transactions.
50 to 47
reserved
-
-
46 to 32
NrBytesTransferred HW — writes
[14:0]
Number of Bytes Transferred: This field indicates the number of bytes
sent or received for this transaction.
reserved
-
DW2
31 to 29
-
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
71 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 71:
Start and complete split for bulk, QHASS/SC: bit description…continued
Bit
Symbol
Access
Description
28 to 25
RL[3:0]
SW — writes
Reload. If RL is set to 0h, hardware ignores the NakCnt value. Set RL
and NakCnt to the same value before a transaction. For full-speed and
low-speed transactions, set this field to 0000b. Not applicable to
isochronous start split and complete split.
24
reserved
-
-
23 to 8
DataStartAddress
[15:0]
SW — writes
Data Start Address: This is the start address for the data that will be
sent or received on or from the USB bus. This is the internal memory
address and not the direct CPU address.
RAM address = (CPU address − 400h)/8
7 to 0
reserved
-
-
63 to 57
HubAddress[6:0]
SW — writes
Hub Address: This indicates the hub address. Zero for the internal or
embedded hub.
56 to 50
PortNumber[6:0]
SW — writes
Port Number: This indicates the port number of the hub or embedded
TT.
49 to 48
SE[1:0]
SW — writes
This depends on the endpoint type and direction. It is valid only for split
transactions. The following applies to start split and complete split only.
DW1
Bulk Control
S
E
Remarks
I/O
I/O
1
0
low-speed
I/O
I/O
0
0
full-speed
47
reserved
-
-
46
S
SW — writes
This bit indicates whether a split transaction has to be executed:
0 — High-speed transaction
1 — Split transaction.
45 to 44
EPType[1:0]
SW — writes
Endpoint Type:
00 — Control
10 — Bulk.
43 to 42
Token[1:0]
SW — writes
Token: This field indicates the PID for this transaction.
00 — OUT
01 — IN
10 — SETUP.
41 to 35
DeviceAddress
[6:0]
SW — writes
Device Address: This is the USB address of the function containing the
endpoint that is referred to by this buffer.
34 to 32
EndPt[3:1]
SW — writes
Endpoint: This is the USB address of the endpoint within the function.
DW0
31
EndPt[0]
SW — writes
Endpoint: This is the USB address of the endpoint within the function.
30 to 29
reserved
-
-
28 to 18
MaximumPacket
Length[10:0]
SW — writes
Maximum Packet Length: This field indicates the maximum number of
bytes that can be sent to or received from an endpoint in a single data
packet. The maximum packet size for full-speed is 64 bytes as defined
in the Universal Serial Bus Specification Rev. 2.0.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
72 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 71:
Start and complete split for bulk, QHASS/SC: bit description…continued
Bit
Symbol
Access
Description
17 to 3
NrBytesToTransfer
[14:0]
SW — writes
Number of Bytes to Transfer: This field indicates the number of bytes
that can be transferred by this data structure. It is used to indicate the
depth of the DATA field.
2 to 1
reserved
-
-
0
V
SW — sets
Valid:
HW — resets
0 — This bit is deactivated when the entire PTD is executed—across
µSOF and SOF—or when a fatal error is encountered.
1 — Software updates to one when there is payload to be sent or
received even across ms boundary. The current PTD is active.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
73 of 105
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx
xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Table 72:
Bit
Start and complete split for isochronous, SiTD: bit allocation
63
62
61
60
59
58
57
56 55
54
53
DW7
ISO_IN_2[7:0]
A
H
DW1
Bit
B
30
29
DW6
X
[1]
S
C
50
49
48
47
46
45
44
43
42
41
40
39
38
37
28
27
25
24
23
Rev. 01 — 8 November 2004
Status7
[2:0]
Status6
[2:0]
22
21
20
18
Status4
[2:0]
[1]
16
15
14
EP
Type
[1:0]
13
Status2
[2:0]
DataStartAddress[15:0]
TT_MPS_Len[10:0]
[1]
Reserved.
[2]
Note the change in the position of USCS[7:0] and NrBytesReceived_CS_IN.
[3]
EndPt[0].
12
Token
[1:0]
11
DeviceAddress[6:0]
10
9
8
7
6
5
ISO_IN_4[7:0]
Status3
[2:0]
reserved
[3]
17
S
ISO_IN_5[7:0]
Status5
[2:0]
34
33
32
NrBytesTransferred[11:0]
reserved
19
35
µSCS[7:0] [2]
ISO_IN_0[7:0]
PortNumber[6:0]
26
36
ISO_IN_7[7:0]
reserved
D
T
ISO_IN_6[7:0]
DW2
DW0
51
ISO_IN_1[7:0]
HubAddress[6:0]
31
DW4
52
reserved
DW5
DW3
Philips Semiconductors
9397 750 13257
Product data sheet
9.5 Start and complete split for isochronous, Split isochronous Transfer Descriptor (SiTD)
(patent-pending)
Status1
[2:0]
4
EndPt[3:0]
(31 to 34)
3
2
1
0
ISO_IN_3[7:0]
µSA[7:0]
Status0
[2:0]
µFrame[7:0] (full-speed)
NrBytesToTransfer[14:0] (1 kbyte for full-speed)
[1]
V
ISP1760
Embedded Hi-Speed USB host controller
74 of 105
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 73:
Start and complete split for isochronous, SiTD: bit description
Bit
Symbol
Access
Description
63 to 40
reserved
-
-
39 to 32
ISO_IN_7[7:0]
HW — writes
Bytes received during µSOF7, if µSA[7] is set to 1 and frame number is
correct.
31 to 24
ISO_IN_6[7:0]
HW — writes
Bytes received during µSOF6, if µSA[6] is set to 1 and frame number is
correct.
23 to 16
ISO_IN_5[7:0]
HW — writes
Bytes received during µSOF5, if µSA[5] is set to 1 and frame number is
correct.
15 to 8
ISO_IN_4[7:0]
HW — writes
Bytes received during µSOF4, if µSA[4] is set to 1 and frame number is
correct.
7 to 0
ISO_IN_3[7:0]
HW — writes
Bytes received during µSOF3, if µSA[3] is set to 1 and frame number is
correct.
63 to 56
ISO_IN_2[7:0]
HW — writes
Bytes received during µSOF2 (bits 7 to 0), if µSA[2] is set to 1 and
frame number is correct.
55 to 48
ISO_IN_1[7:0]
HW — writes
Bytes received during µSOF1, if µSA[1] is set to 1 and frame number is
correct.
47 to 40
ISO_IN_0[7:0]
HW — writes
Bytes received during µSOF0 if µSA[0] is set to 1 and frame number is
correct.
39 to 32
µSCS[7:0]
SW — writes
(0 => 1)
All bits can be set to one for every transfer. It specifies which µSOF the
complete split needs to be sent. Valid only for IN. Start split (SS) and
complete split (CS) active bits—µSA = 0000 0001, µS CS = 0000
0100—will cause SS to execute in µFrame0 and CS in µFrame2.
DW7
DW6
DW5
HW — writes
(1 => 0)
After processing
DW4
31 to 29
Status7[2:0]
HW — writes
isochronous IN or OUT status of µSOF7
28 to 26
Status6[2:0]
HW — writes
isochronous IN or OUT status of µSOF6
25 to 23
Status5[2:0]
HW — writes
isochronous IN or OUT status of µSOF5
22 to 20
Status4[2:0]
HW — writes
isochronous IN or OUT status of µSOF4
19 to 17
Status3[2:0]
HW — writes
isochronous IN or OUT status of µSOF3
16 to 14
Status2[2:0]
HW — writes
isochronous IN or OUT status of µSOF2
13 to 11
Status1[2:0]
HW — writes
isochronous IN or OUT status of µSOF1
10 to 8
Status0[2:0]
HW — writes
isochronous IN or OUT status of µSOF0
Bit 0 — Transaction Error (IN and OUT)
Bit 1 — Babble (IN token only)
Bit 2 — underrun (OUT token only).
7 to 0
µSA[7:0]
Specifies which µSOF the start split needs to be placed.
SW — writes
(0 => 1)
For OUT token: When the frame number of bits DW1(7-3) matches the
frame number of the USB bus, these bits are checked for one before
they are sent for the µSOF.
HW — writes
(1 => 0)
After processing
For IN token: Only µSOF0, µSOF1, µSOF2 or µSOF3 can be set to 1.
Nothing can be set for µSOF4 and above.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
75 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 73:
Start and complete split for isochronous, SiTD: bit description…continued
Bit
Symbol
Access
Description
63
A
SW — sets
Active: Write the same value as that in V.
62
H
HW — writes
Halt: The Halt bit is set when any microframe transfer status has a
stalled or halted condition.
61
B
HW — writes
Babble: This bit corresponds to bit 1 of Status0 to Status7 for every
microframe transfer status.
60
X
HW — writes
Transaction Error: This bit corresponds to bit 0 of Status0 to Status7
for every microframe transfer status.
59
SC
SW — writes 0
Start/Complete:
HW — updates
0 — Start split
DW3
HW — resets
1 — Complete split.
58
reserved
-
-
57
DT
HW — writes
Data Toggle: Set the Data Toggle bit to start for the PTD.
SW — writes
56 to 44
reserved
43 to 32
NrBytesTransferred HW — writes
[11:0]
-
Number of Bytes Transferred: This field indicates the number of bytes
sent or received for this transaction.
31 to 24
reserved
-
-
23 to 8
DataStartAddress
[15:0]
SW — writes
Data Start Address: This is the start address for the data that will be
sent or received on or from the USB bus. This is the internal memory
address and not the CPU address.
7 to 0
µFrame[7:0]
SW — writes
Bits 7 to 3 determine which frame to execute.
63 to 57
HubAddress
[6:0]
SW — writes
Hub Address: This indicates the hub address. Zero for the internal or
embedded hub.
56 to 50
PortNumber
[6:0]
SW — writes
Port Number: This indicates the port number of the hub or embedded
TT.
49 to 47
reserved
-
-
46
S
SW — writes
DW2
DW1
This bit indicates whether a split transaction has to be executed:
0 — High-speed transaction
1 — Split transaction.
45 to 44
EPType[1:0]
SW — writes
Transaction type:
01 — Isochronous.
43 to 42
Token[1:0]
SW — writes
Token PID for this transaction:
00 — OUT
01 — IN.
41 to 35
Device
Address[6:0]
SW — writes
Device Address: This is the USB address of the function containing the
endpoint that is referred to by this buffer.
34 to 32
EndPt[3:1]
SW — writes
Endpoint: This is the USB address of the endpoint within the function.
DW0
31
EndPt[0]
SW — writes
Endpoint: This is the USB address of the endpoint within the function.
30 to 29
reserved
-
-
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
76 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 73:
Start and complete split for isochronous, SiTD: bit description…continued
Bit
Symbol
Access
Description
28 to 18
TT_MPS_Len
[10:0]
SW — writes
Transaction Translator Maximum Packet Size Length: This field
indicates the maximum number of bytes that can be sent per start split
depending on the number of total bytes needed. If the total bytes to be
sent for the entire ms is greater than 188 bytes, this field should be set
to 188 bytes for an OUT token and 192 byes for an IN token. Otherwise,
this field should be equal to the total bytes sent.
17 to 3
NrBytesTo
Transfer
[14:0]
SW — writes
Number of Bytes to Transfer: This field indicates the number of bytes
that can be transferred by this data structure. It is used to indicate the
depth of the DATA field. This field is restricted to 1023 bytes because in
SiTD the maximum allowable payload for a full-speed device is
1023 bytes. This field indirectly becomes the maximum packet size of
the downstream device.
2 to 1
reserved
-
-
0
V
SW — sets
0 — This bit is deactivated when the entire PTD is executed—across
µSOF and SOF—or when a fatal error is encountered.
HW — resets
1 — Software updates to one when there is payload to be sent or
received even across ms boundary. The current PTD is active.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
77 of 105
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx
xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Table 74:
Bit
Start and complete split for interrupt: bit allocation
63
62
61
60
59
58
57
56 55
54
53
DW7
INT_IN_2[7:0]
A
H
DW1
Bit
B
30
29
DW6
[1]
S
C
51
50
49
48
47
46
45
44
43
42
41
40
39
38
28
27
26
Cerr
[1:0]
24
23
Rev. 01 — 8 November 2004
Status7
[2:0]
Status6
[2:0]
22
21
[1]
Reserved.
[2]
EndPt[0].
[1]
SE[1:0]
19
Status5
[2:0]
Status4
[2:0]
18
17
16
-
S
15
14
EP
Type
[1:0]
13
12
Token
[1:0]
34
11
DeviceAddress[6:0]
10
9
INT_IN_4[7:0]
Status3
[2:0]
Status2
[2:0]
DataStartAddress[15:0]
MaxPacketLength[10:0]
35
33
32
NrBytesTransferred[11:0] (4 kbytes for full-speed and
low-speed)
INT_IN_5[7:0]
reserved
[2]
20
36
µSCS[7:0]
INT_IN_0[7:0]
reserved
PortNumber[6:0]
25
37
INT_IN_7[7:0]
INT_IN_1[7:0]
D
T
INT_IN_6[7:0]
DW2
DW0
X
HubAddress[6:0]`
31
DW4
52
reserved
DW5
DW3
Philips Semiconductors
9397 750 13257
Product data sheet
9.6 Start and complete split for interrupt (patent-pending)
Status1
[2:0]
8
7
6
5
4
EndPt
[3:0]
3
2
1
0
INT_IN_3[7:0]
Status0
[2:0]
µSA[7:0]
µFrame[7:0] (full-speed and
low-speed)
NrBytesToTransfer[14:0] (4 kbytes for full-speed and low-speed)
[1]
V
ISP1760
Embedded Hi-Speed USB host controller
78 of 105
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 75:
Start and complete split for interrupt: bit description
Bit
Symbol
Access
Description
63 to 40
reserved
-
-
39 to 32
INT_IN_7[7:0]
HW — writes
Bytes received during µSOF7, if µSA[7] is set to 1 and frame number is
correct. The new value continuously overwrites the old value.
31 to 24
INT_IN_6[7:0]
HW — writes
Bytes received during µSOF6, if µSA[6] is set to 1 and frame number is
correct. The new value continuously overwrites the old value.
23 to 16
INT_IN_5[7:0]
HW — writes
Bytes received during µSOF5, if µSA[5] is set to 1 and frame number is
correct. The new value continuously overwrites the old value.
15 to 8
INT_IN_4[7:0]
HW — writes
Bytes received during µSOF4, if µSA[4] is set to 1 and frame number is
correct. The new value continuously overwrites the old value.
7 to 0
INT_IN_3[7:0]
HW — writes
Bytes received during µSOF3, if µSA[3] is set to 1 and frame number is
correct. The new value continuously overwrites the old value.
63 to 56
INT_IN_2[7:0]
HW — writes
Bytes received during µSOF2 (bits 7 to 0), if µSA[2] is set to 1 and
frame number is correct. The new value continuously overwrites the old
value.
55 to 48
INT_IN_1[7:0]
HW — writes
Bytes received during µSOF1, if µSA[1] is set to 1 and frame number is
correct. The new value continuously overwrites the old value.
47 to 40
INT_IN_0[7:0]
HW — writes
Bytes received during µSOF0 if µSA[0] is set to 1 and frame number is
correct. The new value continuously overwrites the old value.
39 to 32
µSCS[7:0]
SW — writes (0 => 1) All bits can be set to one for every transfer. It specifies which µSOF the
complete split needs to be sent. Valid only for IN. Start split (SS) and
HW — writes
complete split (CS) active bits—µSA = 0000 0001, µS CS = 0000
(1 => 0)
0100—will cause SS to execute in µFrame0 and CS in µFrame2.
After processing
Status7[2:0]
HW — writes
DW7
DW6
DW5
DW4
31 to 29
interrupt IN or OUT status of µSOF7
28 to 26
Status6[2:0]
HW — writes
interrupt IN or OUT status of µSOF6
25 to 23
Status5[2:0]
HW — writes
interrupt IN or OUT status of µSOF5
22 to 20
Status4[2:0]
HW — writes
interrupt IN or OUT status of µSOF4
19 to 17
Status3[2:0]
HW — writes
interrupt IN or OUT status of µSOF3
16 to 14
Status2[2:0]
HW — writes
interrupt IN or OUT status of µSOF2
13 to 11
Status1[2:0]
HW — writes
interrupt IN or OUT status of µSOF1
10 to 8
Status0[2:0]
HW — writes
interrupt IN or OUT status of µSOF0
Bit 0 — Transaction Error (IN and OUT)
Bit 1 — Babble (IN token only)
Bit 2 — underrun (OUT token only).
7 to 0
µSA[7:0]
SW — writes (0 => 1) Specifies which µSOF the start split needs to be placed.
HW — writes
(1 => 0)
After processing
For OUT token: When the frame number of bits DW1(7-3) matches the
frame number of the USB bus, these bits are checked for one before
they are sent for the µSOF.
For IN token: Only µSOF0, µSOF1, µSOF2 or µSOF3 can be set to 1.
Nothing can be set for µSOF4 and above.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
79 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 75:
Start and complete split for interrupt: bit description…continued
Bit
Symbol
Access
Description
63
A
SW — sets
Active: Write the same value as that in V.
62
H
HW — writes
Halt: The Halt bit is set when any microframe transfer status has a
stalled or halted condition.
61
B
HW — writes
Babble: This bit corresponds to bit 1 of Status0 to Status7 for every
microframe transfer status.
60
X
HW — writes
Transaction Error: This bit corresponds to bit 0 of Status0 to Status7
for every microframe transfer status.
59
SC
SW — writes 0
Start/Complete:
HW — updates
0 — Start split
DW3
HW — resets
1 — Complete split.
58
reserved
-
-
57
DT
HW — writes
Data Toggle: For an interrupt transfer, set correct bit to start the PTD.
SW — writes
56 to 55
Cerr[1:0]
HW — writes
Error Counter. This field corresponds to the Cerr[1:0] field in QH.
SW — writes
00 — The transaction will not retry.
11 — The transaction will retry three times. Hardware will decrement
these values. When the transaction has tried three times, X error will be
updated.
54 to 44
reserved
-
-
43 to 32
NrBytes
Transferred
[11:0]
HW — writes
Number of Bytes Transferred: This field indicates the number of
bytes sent or received for this transaction.
31 to 24
reserved
-
-
23 to 8
DataStart
Address[15:0]
SW — writes
Data Start Address: This is the start address for the data that will be
sent or received on or from the USB bus. This is the internal memory
address and not the CPU address.
7 to 0
µFrame[7:0]
SW — writes
Bits 7 to 3 is the ms polling rate. Polling rate is defined as 2(b − 1) µSOF;
where b = 4 to 16. When b is 4, every ms is executed.
DW2
b
Rate
Bits 7 to 3
4
2
00001
5
4
00010 or 00011
6
8
00100 or 00101
7
16
01000 or 01001 up to 32 ms
DW1
63 to 57
HubAddress
[6:0]
SW — writes
Hub Address: This indicates the hub address. Zero for the internal or
embedded hub.
56 to 50
PortNumber
[6:0]
SW — writes
Port Number: This indicates the port number of the hub or embedded
TT.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
80 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 75:
Start and complete split for interrupt: bit description…continued
Bit
Symbol
Access
Description
49 to 48
SE[1:0]
SW — writes
This depends on the endpoint type and direction. It is valid only for split
transactions. The following applies to start split and complete split only.
47
reserved
-
46
S
SW — writes
Interrupt
S
E
Remarks
I/O
1
0
low-speed
I/O
0
0
full-speed
This bit indicates whether a split transaction has to be executed:
0 — High-speed transaction
1 — Split transaction.
45 to 44
EPType[1:0]
SW — writes
Transaction type:
11 — Interrupt.
43 to 42
Token[1:0]
SW — writes
Token PID for this transaction:
00 — OUT
01 — IN.
41 to 35
DeviceAddress
[6:0]
SW — writes
Device Address: This is the USB address of the function containing
the endpoint that is referred to by this buffer.
34 to 32
EndPt[3:1]
SW — writes
Endpoint: This is the USB address of the endpoint within the function.
DW0
31
EndPt[0]
SW — writes
Endpoint: This is the USB address of the endpoint within the function.
30 to 29
reserved
-
-
28 to 18
MaxPacket
Length[10:0]
SW — writes
Maximum Packet Length: This field indicates the maximum number of
bytes that can be sent to or received from an endpoint in a single data
packet. The maximum packet size for the full-speed and low-speed
devices is 64 bytes as defined in the Universal Serial Bus Specification
Rev. 2.0.
17 to 3
NrBytesTo
Transfer[14:0]
SW — writes
Number of Bytes to Transfer: This field indicates the number of bytes
that can be transferred by this data structure. It is used to indicate the
depth of the DATA field. The maximum total number of bytes for this
transaction is 4 kbytes.
2 to 1
reserved
-
-
0
V
SW — sets
0 — This bit is deactivated when the entire PTD is executed—across
µSOF and SOF—or when a fatal error is encountered.
HW — resets
1 — Software updates to one when there is payload to be sent or
received even across ms boundary. The current PTD is active.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
81 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
10. Power consumption
Table 76:
Power consumption
Number of ports working
ICC
ICC(I/O)
VCC = 5.0 V, VCC(I/O) = 3.3 V
90 mA
<10 µA
VCC = 3.3 V, VCC(I/O) = 3.3 V
77 mA
<10 µA
VCC = 5.0 V, VCC(I/O) = 1.8 V
82 mA
<10 µA
VCC = 3.3 V, VCC(I/O) = 1.8 V
77 mA
<10 µA
One port working (high-speed)
Two ports working (high-speed)
VCC = 5.0 V, VCC(I/O) = 3.3 V
110 mA
<10 µA
VCC = 3.3 V, VCC(I/O) = 3.3 V
97 mA
<10 µA
VCC = 5.0 V, VCC(I/O) = 1.8 V
102 mA
<10 µA
VCC = 3.3 V, VCC(I/O) = 1.8 V
97 mA
<10 µA
VCC = 5.0 V, VCC(I/O) = 3.3 V
130 mA
<10 µA
VCC = 3.3 V, VCC(I/O) = 3.3 V
117 mA
<10 µA
VCC = 5.0 V, VCC(I/O) = 1.8 V
122 mA
<10 µA
VCC = 3.3 V, VCC(I/O) = 1.8 V
117 mA
<10 µA
Three ports working (high-speed)
Remark: The idle operating current, that is, when the ISP1760 is in operational
mode—initialized and without any devices connected, is 70 mA. The additional current
consumption on ICC is below 1 mA per port in the case of full-speed and low-speed
devices.
Remark: Deep-sleep suspend mode ensures the lowest power consumption when VCC is
always supplied to the ISP1760. In this case, the suspend current is typically about
100 µA at room temperature. The suspend current may increase if the ambient
temperature increases. For details, see Section 7.6.
Remark: In hybrid mode, when VCC is disconnected ICC(I/O) will be generally below
100 µA. The average value is 60 µA to 70 µA.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
82 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
11. Limiting values
Table 77: Absolute maximum ratings
In accordance with the Absolute Maximum Rating System (IEC 60134).
Symbol
Parameter
Conditions
VCC(I/O)
supply voltage
VCC(5V0)
supply voltage
Ilu
latch-up current
VI < 0 or VI > VCC
Vesd
electrostatic discharge voltage
ILI < 1 µA
Tstg
storage temperature
Min
Max
Unit
−0.5
+3.6
V
−0.5
+5.5
V
-
100
mA
−4000
+4000
V
−40
+125
°C
12. Recommended operating conditions
Table 78:
Recommended operating conditions
Symbol
Parameter
VCC(I/O)
supply voltage
Conditions
Min
Typ
Max
Unit
VCC(I/O) = 3.3 V
3.0
3.3
3.6
V
VCC(I/O) = 1.8 V
1.65
1.8
1.95
V
VCC(5V0)
supply voltage
3.0
-
5.5
V
Tamb
operating temperature
−40
-
+85
°C
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
83 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
13. Static characteristics
Table 79: Static characteristics: digital pins
Digital pins: A[17:1], DATA[31:0], CS_N, RD_N, WR_N, DACK, DREQ, IRQ, RESET_N, SUSPEND/WAKEUP_N, CLKIN,
OC1_N, OC2_N, OC3_N.
OC1_N, OC2_N and OC3_N are used as digital overcurrent pins; VCC(I/O) = 3.0 V to 3.6 V; Tamb = −40 °C to +85 °C; unless
otherwise specified
Symbol
Parameter
VIH
Conditions
Min
Typ
Max
Unit
HIGH-level input voltage
2.0
-
-
V
VIL
LOW-level input voltage
-
-
0.8
V
Vhys
hysteresis voltage
VOL
LOW-level output voltage
VOH
HIGH-level output voltage
IIL
input leakage current
CIN
input pin capacitance
IOL = 3 mA
0 < VIN <VCC(I/O)
0.4
-
0.7
V
-
-
0.4
V
2.4
-
-
V
-
-
1
µA
-
2.75
-
pF
Table 80: Static characteristics: digital pins
Digital pins: A[17:1], DATA[31:0], CS_N, RD_N, WR_N, DACK, DREQ, IRQ, RESET_N, SUSPEND/WAKEUP_N, CLKIN,
OC1_N, OC2_N, OC3_N.
OC1_N, OC2_N and OC3_N are used as digital overcurrent pins; VCC(I/O) = 1.65 V to 1.95 V; Tamb = −40 °C to +85 °C;
unless otherwise specified.
Symbol
Parameter
VIH
Conditions
Min
Typ
Max
Unit
HIGH-level input voltage
1.2
-
-
V
VIL
LOW-level input voltage
-
-
0.5
V
Vhys
hysteresis voltage
0.4
-
0.7
V
VOL
LOW-level output voltage
-
-
0.22VCC(I/O)
V
VOH
HIGH-level output voltage
0.8VCC(I/O)
-
-
V
IIL
input leakage current
-
-
1
µA
CIN
input pin capacitance
-
2.75
-
pF
IOL = 3 mA
0 < VIN <VCC(I/O)
Table 81: Static characteristics: PSW1_N, PSW2_N, PSW3_N
VCC(I/O) = 1.65 V to 3.6 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
VOL
LOW-level output voltage
IOL = 8 mA, pull-up to VCC(5V0)
-
-
0.4
V
VOH
HIGH-level output voltage pull-up to VCC(I/O)
-
VCC(I/O)
-
V
Table 82: Static characteristics: USB interface block (pins DM1 to DM3 and DP1 to DP3)
VCC(I/O) = 1.65 V to 3.6 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
Input levels for high-speed
VHSSQ
squelch detection threshold
(differential signal amplitude)
squelch detected
-
-
100
mV
no squelch detected
150
-
-
mV
VHSDSC
disconnect detection threshold
(differential signal amplitude)
disconnect detected
625
-
-
mV
disconnect not detected
-
-
525
mV
−50
-
+500
mV
VHSCM
data signaling common mode
voltage range
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
84 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 82: Static characteristics: USB interface block (pins DM1 to DM3 and DP1 to DP3)…continued
VCC(I/O) = 1.65 V to 3.6 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
−10
-
+10
mV
Output levels for high-speed
VHSOI
idle state
VHSOH
data signaling HIGH
360
-
440
mV
VHSOL
data signaling LOW
−10
-
+10
mV
VCHIRPJ
Chirp J level (differential
voltage)
700 [1]
-
1100
mV
VCHIRPK
Chirp K level (differential
voltage)
−900 [1]
-
−500
mV
Input levels for full-speed and low-speed
VIH
HIGH-level input voltage (drive)
2.0
-
-
V
VIHZ
HIGH-level input voltage
(floating)
2.7
-
3.6
V
VIL
LOW-level input voltage
-
-
0.8
V
VDI
differential input sensitivity
0.2
-
-
V
VCM
differential common mode range
0.8
-
2.5
V
|VDP − VDM|
Output levels for full-speed and low-speed
VOH
HIGH-level output voltage
2.8
-
3.6
V
VOL
LOW-level output voltage
0
-
0.3
V
VOSEI
SEI
0.8
-
-
V
VCRS
output signal crossover point
voltage
1.3
-
2.0
V
[1]
The HS termination resistor is disabled, and the pull-up resistor is connected. Only during reset, when both the hub and the device are
capable of the high-speed operation.
Table 83: Static characteristics: REF5V
VCC(I/O) = 1.65 V to 3.6 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol
Parameter
VIH
HIGH-level input voltage
Conditions
9397 750 13257
Product data sheet
Min
Typ
Max
Unit
-
5
-
V
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
85 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
14. Dynamic characteristics
Table 84:
Dynamic characteristics: system clock timing
Symbol Parameter
Conditions
Min
Typ
Max
Unit
crystal [2]
-
12
-
MHz
oscillator
-
12
-
MHz
Crystal oscillator
clock frequency [1]
fclk
External clock input
J
external clock jitter
-
-
500
ps
δ
clock duty cycle
-
50
-
%
Vclk
amplitude
-
1.8
-
V
tCR, tCF
rise time and fall time
-
-
3
ns
[1]
Recommended accuracy of the clock frequency is 50 ppm for the crystal and oscillator. The oscillator used depends on VCC(I/O).
[2]
Recommended values for external capacitors when using a crystal are 22 pF to 27 pF.
Table 85: Dynamic characteristics: CPU interface block
VCC(I/O) = 1.65 V to 3.6 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
SR
output slew rate (rise, fall)
standard load
1
-
4
V/ns
Table 86: Dynamic characteristics: high-speed source electrical characteristics
VCC(I/O) = 1.65 V to 3.6 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol Parameter
Conditions
Min
Typ
Max
Unit
Driver characteristics
tHSR
high-speed differential rise time
10 % to 90 %
500
-
-
ps
tHSF
high-speed differential fall time
90 % to 10 %
500
-
-
ps
ZHSDRV
drive output resistance (this also
serves as a high-speed
termination)
includes the RS resistor
40.5
45
49.5
Ω
Clock timing
tHSDRAT
data rate
479.76
-
480.24
Mbit/s
tHSFRAM
microframe interval
124.9375
-
125.0625
µs
tHSRFI
consecutive microframe interval
difference
1
-
four
high-speed
bit times
ns
Table 87: Dynamic characteristics: full-speed source electrical characteristics
VCC(I/O) = 1.65 V to 3.6 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
Driver characteristics
tFR
rise time
CL = 50 pF; 10 % to 90 % of
|VOH − VOL|
4
-
20
ns
tFF
fall time
CL = 50 pF; 90 % to 10 % of
|VOH − VOL|
4
-
20
ns
tFRFM
differential rise and fall time
matching
90
-
111.1
%
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
86 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
Table 87: Dynamic characteristics: full-speed source electrical characteristics…continued
VCC(I/O) = 1.65 V to 3.6 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol
Parameter
Conditions
ZDRV
driver output resistance for
the driver that is not
high-speed capable
Min
Typ
Max
Unit
28
-
44
Ω
−2
-
+5
ns
Data timing: see Figure 11
tFDEOP
source jitter for differential full-speed timing
transition to SEO transition
tFEOPT
source SE0 interval of EOP
160
-
175
ns
tFEOPR
receiver SE0 interval of
EOP
82
-
-
ns
tLDEOP
source jitter for differential low-speed timing
transition to SEO transition
−40
-
+100
ns
tLEOPT
source SE0 interval of EOP
1.25
-
1.5
µs
tLEOPR
receiver SE0 interval of
EOP
670
-
-
ns
tFST
width of SE0 interval during
differential transaction
-
-
14
ns
Min
Typ
Max
Unit
Table 88: Dynamic characteristics: low-speed source electrical characteristics
VCC(I/O) = 1.65 V to 3.6 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol
Parameter
Conditions
Driver characteristics
tLR
rise time
75
-
300
ns
tLF
fall time
75
-
300
ns
tLRFM
differential rise and fall time
matching
90
-
125
%
TPERIOD
+3.3 V
crossover point
extended
crossover point
differential
data lines
0V
differential data to
SE0/EOP skew
N × TPERIOD + t DEOP
source EOP width: t EOPT
receiver EOP width: t EOPR
mgr776
TPERIOD is the bit duration corresponding with the USB data rate.
Full-speed timing symbols have a subscript prefix ‘F’, low-speed timing symbols have a prefix ‘L’.
Fig 11. USB source differential data-to-EOP transition skew and EOP width.
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
87 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
14.1 PIO timing
14.1.1 Register or memory write
th31
A[17:1]
address 01
address 02
tsu21
th21
CS_N
tsu31
tw11
WR_N
tsu11
Tcy11
data 01
DATA
th11
data 02
004aaa527
Fig 12. Register or memory write.
Table 89: Register or memory write
VCC(I/O) = 1.65 V to 1.95 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol
Parameter
Min
Max
Unit
th11
data hold after WR_N HIGH
2
-
ns
th21
CS_N hold after WR_N HIGH
1
-
ns
th31
address hold after WR_N HIGH
2
-
ns
tw11
WR_N pulse width
17
-
ns
Tcy11
WR_N to WR_N cycle time
36
-
ns
tsu11
data set up time before WR_N HIGH
5
-
ns
tsu21
address set up time before WR_N HIGH
5
-
ns
tsu31
CS_N set up time before WR_N HIGH
5
-
ns
Table 90: Register or memory write
VCC(I/O) = 3.3 V to 3.6 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol
Parameter
Min
Max
Unit
th11
data hold after WR_N HIGH
2
-
ns
th21
CS_N hold after WR_N HIGH
1
-
ns
th31
address hold after WR_N HIGH
2
-
ns
tw11
WR_N pulse width
17
-
ns
Tcy11
WR_N to WR_N cycle time
36
-
ns
tsu11
data set up time before WR_N HIGH
5
-
ns
tsu21
address set up time before WR_N HIGH
5
-
ns
tsu31
CS_N set up time before WR_N HIGH
5
-
ns
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
88 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
14.1.2 Register read
tsu12
address 01
A[17:1]
address 02
tsu22
CS_N
td22
tw12
RD_N
Tcy12
DATA
004aaa524
td12
Fig 13. Register read.
Table 91: Register read
VCC(I/O) = 1.65 V to 1.95 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol
Parameter
Min
Max
Unit
tsu12
address set up time before RD_N LOW
0
-
ns
tsu22
CS_N set up time before RD_N LOW
0
-
ns
tw12
RD_N pulse width
td12
-
ns
td12
data valid time after RD_N LOW
-
35
ns
td22
data valid time after RD_N HIGH
-
1
ns
Tcy12
read-to-read cycle time
40
-
ns
Table 92: Register read
VCC(I/O) = 3.3 V to 3.6 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol
Parameter
Min
Max
Unit
tsu12
address set up time before RD_N LOW
0
-
ns
tsu22
CS_N set up time before RD_N LOW
0
-
ns
tw12
RD_N pulse width
td12
-
ns
td12
data valid time after RD_N LOW
-
22
ns
td22
data valid time after RD_N HIGH
-
1
ns
Tcy12
read-to-read cycle time
36
-
ns
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
89 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
14.1.3 Memory read
A[17:1]
address = 33C
address 1
address 2
address 3
tsu23
data
DATA
data 1
data 2
data 3
CS_N
td13
WR_N
tp13
td23
RD_N
004aaa523
Tcy13
tsu13
tw13
Fig 14. Memory read.
Table 93: Memory read
VCC(I/O) = 1.65 V to 1.95 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol
Parameter
Min
Max
Unit
tp13
initial prefetch time
90
-
ns
Tcy13
memory RD_N cycle time
40
-
ns
td13
data valid time after RD_N LOW
-
31
ns
td23
data available time after RD_N HIGH
-
1
ns
tw13
RD_N pulse width
td13
tsu13
CS_N setup time before RD_N LOW
0
-
ns
tsu23
address setup time before RD_N LOW
0
-
ns
ns
Table 94: Memory read
VCC(I/O) = 3.3 V to 3.6 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol
Parameter
Min
Max
Unit
tp13
initial prefetch time
90
-
ns
Tcy13
memory RD_N cycle time
36
-
ns
td13
data valid time after RD_N LOW
-
20
ns
td23
data available time after RD_N HIGH
-
1
ns
tw13
RD_N pulse width
td13
tsu13
CS_N setup time before RD_N LOW
0
-
ns
tsu23
address setup time before RD_N LOW
0
-
ns
9397 750 13257
Product data sheet
ns
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
90 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
14.2 DMA timing
In the following sections:
• Polarity of DACK is active HIGH
• Polarity of DREQ is active HIGH.
14.2.1 Single cycle: DMA read
ta44
DREQ
ta14
ta34
DACK
tw14
RD_N
ta24
td14
DATA
004aaa530
Fig 15. DMA read (single cycle).
Table 95: DMA read (single cycle)
VCC(I/O) = 1.65 V to 1.95 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol
Parameter
Min
Max
Unit
ta14
DACK assertion time after DREQ assertion
0
-
ns
ta24
RD_N assertion time after DACK assertion
0
-
ns
td14
data valid time after RD_N assertion
-
24
ns
tw14
RD_N pulse width
td14
-
ns
ta34
DREQ deassertion time after RD_N assertion
23
ta44
DREQ deassertion to next DREQ assertion time -
-
ns
56
ns
Table 96: DMA read (single cycle)
VCC(I/O) = 3.3 V to 3.6 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol
Parameter
Min
Max
Unit
ta14
DACK assertion time after DREQ assertion
0
-
ns
ta24
RD_N assertion time after DACK assertion
0
-
ns
td14
data valid time after RD_N assertion
-
20
ns
tw14
RD_N pulse width
td14
-
ns
ta34
DREQ deassertion time after RD_N assertion
11
-
ns
ta44
DREQ deassertion to next DREQ assertion time -
56
ns
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
91 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
14.2.2 Single cycle: DMA write
tcy15
DREQ
ta15
ta35
DACK
tw15
ta25
th25
tsu15
WR_N
th15
data
DATA
data 1
004aaa525
DREQ and DACK are active HIGH.
Fig 16. DMA write (single cycle).
Table 97: DMA write (single cycle)
VCC(I/O) = 1.65 V to 1.95 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol Parameter
Min
Max
Unit
ta15
DACK assertion time after DREQ assertion
0
-
ns
ta25
WR_N assertion time after DACK assertion
1
-
ns
th15
data hold time after WR_N deassertion
3
-
ns
th25
DACK hold time after WR_N deassertion
0
-
ns
tsu15
data set-up time before WR_N deassertion
5.5
-
ns
ta35
DREQ deassertion time after WR_N assertion
22
-
ns
tcy15
last DACK strobe deassertion to next DREQ
assertion time
82
-
ns
tw15
WR_N pulse width
22
-
ns
Table 98: DMA write (single cycle)
VCC(I/O) = 3.3 V to 3.6 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol Parameter
Min
Max
Unit
ta15
DACK assertion time after DREQ assertion
0
-
ns
ta25
WR_N assertion time after DACK assertion
1
-
ns
th15
data hold time after WR_N deassertion
2
-
ns
th25
DACK hold time after WR_N deassertion
0
-
ns
tsu15
data set-up time before WR_N deassertion
5.5
-
ns
ta35
DREQ deassertion time after WR_N assertion
8.9
-
ns
tcy15
last DACK strobe deassertion to next DREQ
assertion time
82
-
ns
tw15
WR_N pulse width
22
-
ns
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
92 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
14.2.3 Multicycle: DMA read
ta36
ta46
DREQ
ta16
DACK
ta26
Tcy16
tw16
RD_N
td16
DATA
data 0
data n-1
data 1
data n
004aaa531
DREQ and DACK are active HIGH.
Fig 17. DMA read (multicycle burst).
Table 99: DMA read (multicycle burst)
VCC(I/O) = 1.65 V to 1.95 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol Parameter
Min
Max
Unit
ta16
DACK assertion after DREQ assertion time
0
-
ns
ta26
RD_N assertion after DACK assertion time
0
-
ns
td16
data valid time after RD_N assertion
-
31
ns
tw16
RD_N pulse width
td16
-
ns
Tcy16
read-to-read cycle time
40
-
ns
ta36
DREQ deassertion time after last burst RD_N
deassertion
20
-
ns
ta46
DACK deassertion to next DREQ assertion time -
82
ns
Table 100: DMA read (multicycle burst)
VCC(I/O) = 3.3 V to 3.6 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Min
Max
Unit
ta16
Symbol Parameter
DACK assertion after DREQ assertion time
0
-
ns
ta26
RD_N assertion after DACK assertion time
0
-
ns
td16
data valid time after RD_N assertion
-
16
ns
tw16
RD_N pulse width
td16
-
ns
Tcy16
read-to-read cycle time
36
-
ns
ta36
DREQ deassertion time after last burst RD_N
deassertion
11
-
ns
ta46
DACK deassertion to next DREQ assertion time -
82
ns
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
93 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
14.2.4 Multicycle: DMA write
ta57
DREQ
ta17
th27
DACK
tsu17
ta37
Tcy17
tw17
WR_N
ta47
ta27
th17
DATA
data 1
data 2
data n-1
data n 004aaa526
Fig 18. DMA write (multicycle burst).
Table 101: DMA write (multicycle burst)
VCC(I/O) = 1.65 V to 1.95 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol Parameter
Min
Max
Unit
Tcy17
DMA write cycle time
51
-
ns
tsu17
data setup time before WR_N deassertion
5
-
ns
th17
data hold time after WR_N deassertion
2
-
ns
ta17
DACK assertion time after DREQ assertion
0
-
ns
ta27
WR_N assertion time after DACK assertion
2
-
ns
ta37
DREQ deassertion time at last strobe (WR_N)
assertion
20
-
ns
th27
DACK hold time after WR_N deassertion
0
-
ns
ta47
strobe deassertion to next strobe assertion time
34
-
ns
tw17
WR_N pulse width
17
-
ns
ta57
DACK deassertion to next DREQ assertion time
-
82
ns
Table 102: DMA write (multicycle burst)
VCC(I/O) = 3.3 V to 3.6 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol Parameter
Min
Max
Unit
Tcy17
DMA write cycle time
51
-
ns
tsu17
data setup time before WR_N deassertion
5
-
ns
th17
data hold time after WR_N deassertion
2
-
ns
ta17
DACK assertion time after DREQ assertion
0
-
ns
ta27
WR_N assertion time after DACK assertion
1
-
ns
ta37
DREQ deassertion time at last strobe (WR_N)
assertion
0
-
ns
th27
DACK hold time after WR_N deassertion
0
-
ns
ta47
strobe deassertion to next strobe assertion time
34
-
ns
tw17
WR_N pulse width
17
-
ns
ta57
DACK deassertion to next DREQ assertion time
-
82
ns
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
94 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
15. Package outline
LQFP128: plastic low profile quad flat package; 128 leads; body 14 x 20 x 1.4 mm
SOT425-1
c
y
X
A
102
103
65
64
ZE
e
E HE
A A2 A
1
(A 3)
θ
wM
Lp
bp
pin 1 index
L
detail X
39
128
1
38
v M A
ZD
wM
bp
e
D
B
HD
v M B
0
5
10 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (1)
e
mm
1.6
0.15
0.05
1.45
1.35
0.25
0.27
0.17
0.20
0.09
20.1
19.9
14.1
13.9
0.5
HD
HE
22.15 16.15
21.85 15.85
L
Lp
v
w
y
1
0.75
0.45
0.2
0.12
0.1
Z D(1) Z E(1)
0.81
0.59
0.81
0.59
θ
7o
o
0
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
SOT425-1
136E28
MS-026
JEITA
EUROPEAN
PROJECTION
ISSUE DATE
00-01-19
03-02-20
Fig 19. Package outline (LQFP128).
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
95 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
16. Soldering
16.1 Introduction to soldering surface mount packages
This text gives a very brief insight to a complex technology. A more in-depth account of
soldering ICs can be found in our Data Handbook IC26; Integrated Circuit Packages
(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface mount IC packages. Wave
soldering can still be used for certain surface mount ICs, but it is not suitable for fine pitch
SMDs. In these situations reflow soldering is recommended.
16.2 Reflow soldering
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and
binding agent) to be applied to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement. Driven by legislation and
environmental forces the worldwide use of lead-free solder pastes is increasing.
Several methods exist for reflowing; for example, convection or convection/infrared
heating in a conveyor type oven. Throughput times (preheating, soldering and cooling)
vary between 100 and 200 seconds depending on heating method.
Typical reflow peak temperatures range from 215 to 270 °C depending on solder paste
material. The top-surface temperature of the packages should preferably be kept:
• below 225 °C (SnPb process) or below 245 °C (Pb-free process)
– for all BGA, HTSSON..T and SSOP..T packages
– for packages with a thickness ≥ 2.5 mm
– for packages with a thickness < 2.5 mm and a volume ≥ 350 mm3 so called
thick/large packages.
• below 240 °C (SnPb process) or below 260 °C (Pb-free process) for packages with a
thickness < 2.5 mm and a volume < 350 mm3 so called small/thin packages.
Moisture sensitivity precautions, as indicated on packing, must be respected at all times.
16.3 Wave soldering
Conventional single wave soldering is not recommended for surface mount devices
(SMDs) or printed-circuit boards with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering method was specifically
developed.
If wave soldering is used the following conditions must be observed for optimal results:
• Use a double-wave soldering method comprising a turbulent wave with high upward
pressure followed by a smooth laminar wave.
• For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be
parallel to the transport direction of the printed-circuit board;
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
96 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
– smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the
transport direction of the printed-circuit board.
The footprint must incorporate solder thieves at the downstream end.
• For packages with leads on four sides, the footprint must be placed at a 45° angle to
the transport direction of the printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must be fixed with a droplet of
adhesive. The adhesive can be applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the adhesive is cured.
Typical dwell time of the leads in the wave ranges from 3 to 4 seconds at 250 °C or
265 °C, depending on solder material applied, SnPb or Pb-free respectively.
A mildly-activated flux will eliminate the need for removal of corrosive residues in most
applications.
16.4 Manual soldering
Fix the component by first soldering two diagonally-opposite end leads. Use a low voltage
(24 V or less) soldering iron applied to the flat part of the lead. Contact time must be
limited to 10 seconds at up to 300 °C.
When using a dedicated tool, all other leads can be soldered in one operation within
2 to 5 seconds between 270 and 320 °C.
16.5 Package related soldering information
Table 103: Suitability of surface mount IC packages for wave and reflow soldering methods
Package [1]
Soldering method
Wave
Reflow [2]
BGA, HTSSON..T [3], LBGA, LFBGA, SQFP,
SSOP..T [3], TFBGA, USON, VFBGA
not suitable
suitable
DHVQFN, HBCC, HBGA, HLQFP, HSO, HSOP,
HSQFP, HSSON, HTQFP, HTSSOP, HVQFN,
HVSON, SMS
not suitable [4]
suitable
PLCC [5], SO, SOJ
suitable
suitable
not
recommended [5] [6]
suitable
SSOP, TSSOP, VSO, VSSOP
not
recommended [7]
suitable
CWQCCN..L [8], PMFP [9], WQCCN..L [8]
not suitable
LQFP, QFP, TQFP
[1]
For more detailed information on the BGA packages refer to the (LF)BGA Application Note (AN01026);
order a copy from your Philips Semiconductors sales office.
[2]
All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the
maximum temperature (with respect to time) and body size of the package, there is a risk that internal or
external package cracks may occur due to vaporization of the moisture in them (the so called popcorn
effect). For details, refer to the Drypack information in the Data Handbook IC26; Integrated Circuit
Packages; Section: Packing Methods.
[3]
These transparent plastic packages are extremely sensitive to reflow soldering conditions and must on no
account be processed through more than one soldering cycle or subjected to infrared reflow soldering with
peak temperature exceeding 217 °C ± 10 °C measured in the atmosphere of the reflow oven. The package
body peak temperature must be kept as low as possible.
9397 750 13257
Product data sheet
not suitable
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
97 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
[4]
These packages are not suitable for wave soldering. On versions with the heatsink on the bottom side, the
solder cannot penetrate between the printed-circuit board and the heatsink. On versions with the heatsink
on the top side, the solder might be deposited on the heatsink surface.
[5]
If wave soldering is considered, then the package must be placed at a 45° angle to the solder wave
direction. The package footprint must incorporate solder thieves downstream and at the side corners.
[6]
Wave soldering is suitable for LQFP, QFP and TQFP packages with a pitch (e) larger than 0.8 mm; it is
definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm.
[7]
Wave soldering is suitable for SSOP, TSSOP, VSO and VSOP packages with a pitch (e) equal to or larger
than 0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm.
[8]
Image sensor packages in principle should not be soldered. They are mounted in sockets or delivered
pre-mounted on flex foil. However, the image sensor package can be mounted by the client on a flex foil by
using a hot bar soldering process. The appropriate soldering profile can be provided on request.
[9]
Hot bar soldering or manual soldering is suitable for PMFP packages.
17. Abbreviations
Table 104: Abbreviations
Acronym
Description
ATL
Acknowledged Transfer List
DMA
Direct Memory Access
DSC
Digital Still Camera
EHCI
Enhanced Host Controller Interface
EMI
Electro-Magnetic Interference
FS
full-speed
HC
Host Controller
HS
high-speed
INT
INTerrupt
ISO
isochronous
iTD
isochronous Transfer Descriptor
ITL
Isochronous (ISO) Transfer List
LS
low-speed
OHCI
Open Host Controller Interface
PDA
Personal Digital Assistant
PLL
Phase-Locked Loop
PIO
Programmed Input/Output
PTD
Philips Transfer Descriptor
QHA
Queue Head Asynchronous
QHP
Queue Head Periodic
QHA-SS/SC
Queue Head Asynchronous-Start Split/Start Complete
SiTD
Split isochronous Transfer Descriptor
TT
Transaction Translator
UHCI
Universal Host Controller Interface
USB
Universal Serial Bus
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
98 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
18. References
[1]
Universal Serial Bus Specification Rev. 2.0
[2]
Enhanced Host Controller Interface Specification for Universal Serial Bus Rev. 1.0
[3]
On-The-Go Supplement to the USB Specification Rev. 1.0a
[4]
Embedded Systems Design with the ISP176x (AN10043)
[5]
ISP176x Linux Programming Guide (AN10042)
[6]
Interfacing the ISP76x to the Intel® PXA250 Processor (AN10037).
19. Revision history
Table 105: Revision history
Document ID
Release date
Data sheet status
Change notice
Doc. number
Supersedes
ISP1760_1
20041108
Product data sheet
-
9397 750 13257
-
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
99 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
20. Data sheet status
Level
Data sheet status [1]
Product status [2] [3]
Definition
I
Objective data
Development
This data sheet contains data from the objective specification for product development. Philips
Semiconductors reserves the right to change the specification in any manner without notice.
II
Preliminary data
Qualification
This data sheet contains data from the preliminary specification. Supplementary data will be published
at a later date. Philips Semiconductors reserves the right to change the specification without notice, in
order to improve the design and supply the best possible product.
III
Product data
Production
This data sheet contains data from the product specification. Philips Semiconductors reserves the
right to make changes at any time in order to improve the design, manufacturing and supply. Relevant
changes will be communicated via a Customer Product/Process Change Notification (CPCN).
[1]
Please consult the most recently issued data sheet before initiating or completing a design.
[2]
The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at
URL http://www.semiconductors.philips.com.
[3]
For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status.
21. Definitions
customers using or selling these products for use in such applications do so
at their own risk and agree to fully indemnify Philips Semiconductors for any
damages resulting from such application.
Short-form specification — The data in a short-form specification is
extracted from a full data sheet with the same type number and title. For
detailed information see the relevant data sheet or data handbook.
Right to make changes — Philips Semiconductors reserves the right to
make changes in the products - including circuits, standard cells, and/or
software - described or contained herein in order to improve design and/or
performance. When the product is in full production (status ‘Production’),
relevant changes will be communicated via a Customer Product/Process
Change Notification (CPCN). Philips Semiconductors assumes no
responsibility or liability for the use of any of these products, conveys no
license or title under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that these products are
free from patent, copyright, or mask work right infringement, unless otherwise
specified.
Limiting values definition — Limiting values given are in accordance with
the Absolute Maximum Rating System (IEC 60134). Stress above one or
more of the limiting values may cause permanent damage to the device.
These are stress ratings only and operation of the device at these or at any
other conditions above those given in the Characteristics sections of the
specification is not implied. Exposure to limiting values for extended periods
may affect device reliability.
Application information — Applications that are described herein for any
of these products are for illustrative purposes only. Philips Semiconductors
make no representation or warranty that such applications will be suitable for
the specified use without further testing or modification.
23. Trademarks
Intel — is a registered trademark of Intel Corporation.
22. Disclaimers
Life support — These products are not designed for use in life support
appliances, devices, or systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips Semiconductors
24. Contact information
For additional information, please visit: http://www.semiconductors.philips.com
For sales office addresses, send an email to: [email protected]
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
100 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
25. Tables
Table 1:
Table 2:
Table 3:
Table 4:
Table 5:
Table 6:
Table 7:
Table 8:
Table 9:
Table 10:
Table 11:
Table 12:
Table 13:
Table 14:
Table 15:
Table 16:
Table 17:
Table 18:
Table 19:
Table 20:
Table 21:
Table 22:
Table 23:
Table 24:
Table 25:
Table 26:
Table 27:
Table 28:
Table 29:
Table 30:
Table 31:
Table 32:
Table 33:
Table 34:
Table 35:
Table 36:
Table 37:
Table 38:
Table 39:
Table 40:
Table 41:
Table 42:
Table 43:
Table 44:
Table 45:
Table 46:
Table 47:
Ordering information . . . . . . . . . . . . . . . . . . . . .3
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . .5
Memory address . . . . . . . . . . . . . . . . . . . . . . .15
Using the IRQ Mask AND or IRQ Mask OR
registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Register overview . . . . . . . . . . . . . . . . . . . . . .27
CAPLENGTH register: bit description . . . . . . .28
HCIVERSION register: bit description . . . . . . .28
HCSPARAMS register: bit allocation . . . . . . . .28
HCSPARAMS register: bit description . . . . . . .29
HCCPARAMS register: bit allocation . . . . . . . .29
HCCPARAMS register: bit description . . . . . . .30
USBCMD register: bit allocation . . . . . . . . . . .31
USBCMD register: bit description . . . . . . . . . .31
USBSTS register: bit allocation . . . . . . . . . . . .32
USBSTS register: bit description . . . . . . . . . . .32
USBINTR register: bit allocation . . . . . . . . . . .32
USBINTR register: bit description . . . . . . . . . .33
FRINDEX register: bit allocation . . . . . . . . . . .33
FRINDEX register: bit description . . . . . . . . . .34
CONFIGFLAG register: bit allocation . . . . . . .34
CONFIGFLAG register: bit description . . . . . .35
PORTSC1 register: bit allocation . . . . . . . . . . .35
PORTSC1 register: bit description . . . . . . . . . .36
ISO PTD Done Map register: bit description . .37
ISO PTD Skip Map register: bit description . . .37
ISO PTD Last PTD register: bit description . . .37
INT PTD Done Map register: bit description . .37
INT PTD Skip Map register: bit description . . .38
INT PTD Last PTD register: bit description . . .38
ATL PTD Done Map register: bit description . .38
ATL PTD Skip Map register: bit description . . .39
ATL PTD Last PTD register: bit description . . .39
HW Mode Control register: bit allocation . . . . .39
HW Mode Control register: bit description . . . .40
Chip ID register: bit description . . . . . . . . . . . .41
Scratch register: bit description . . . . . . . . . . . .41
SW Reset register: bit allocation . . . . . . . . . . .41
SW Reset register: bit description . . . . . . . . . .42
DMA Configuration register: bit allocation . . . .42
DMA Configuration register: bit description . . .43
Buffer Status register: bit allocation . . . . . . . . .43
Buffer Status register: bit description . . . . . . . .44
ATL Done Timeout register: bit description . . .44
Memory register: bit allocation . . . . . . . . . . . . .44
Memory register: bit description . . . . . . . . . . .45
Edge Interrupt Count register: bit allocation . .45
Edge Interrupt Count register: bit description .46
Table 48:
Table 49:
Table 50:
Table 51:
Table 52:
Table 53:
Table 54:
Table 55:
Table 56:
Table 57:
Table 58:
Table 59:
Table 60:
Table 61:
Table 62:
Table 63:
Table 64:
Table 65:
Table 66:
Table 67:
Table 68:
Table 69:
Table 70:
Table 71:
Table 72:
Table 73:
Table 74:
Table 75:
Table 76:
Table 77:
Table 78:
Table 79:
Table 80:
Table 81:
Table 82:
DMA Start Address register: bit allocation . . . 46
DMA Start Address register: bit description . . 46
Power Down Control register: bit allocation . . 47
Power Down Control register: bit description . 47
Port 1 Control register: bit allocation . . . . . . . . 49
Port 1 Control register: bit description . . . . . . . 49
Interrupt register: bit allocation . . . . . . . . . . . . 50
Interrupt register: bit description . . . . . . . . . . . 50
Interrupt Enable register: bit allocation . . . . . . 51
Interrupt Enable register: bit description . . . . . 52
ISO IRQ Mask OR register: bit description . . . 53
INT IRQ Mask OR register: bit description . . . 53
ATL IRQ Mask OR register: bit description . . . 54
ISO IRQ Mask AND register: bit description . . 54
INT IRQ Mask AND register: bit description . . 54
ATL IRQ Mask AND register: bit description . . 55
High-speed bulk IN and OUT, QHA: bit
allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
High-speed bulk IN and OUT, QHA: bit
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
High-speed isochronous IN and OUT, iTD: bit
allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
High-speed isochronous IN and OUT, iTD: bit
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
High-speed interrupt IN and OUT, QHP: bit
allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
High-speed interrupt IN and OUT, QHP: bit
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Start and complete split for bulk, QHASS/SC: bit
allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Start and complete split for bulk, QHASS/SC: bit
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Start and complete split for isochronous, SiTD: bit
allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Start and complete split for isochronous, SiTD: bit
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Start and complete split for interrupt: bit
allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Start and complete split for interrupt: bit
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Power consumption . . . . . . . . . . . . . . . . . . . . . 82
Absolute maximum ratings . . . . . . . . . . . . . . . 83
Recommended operating conditions . . . . . . . . 83
Static characteristics: digital pins . . . . . . . . . . 84
Static characteristics: digital pins . . . . . . . . . . 84
Static characteristics: PSW1_N, PSW2_N,
PSW3_N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Static characteristics: USB interface block (pins
continued >>
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
101 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
DM1 to DM3 and DP1 to DP3) . . . . . . . . . . . .84
Static characteristics: REF5V . . . . . . . . . . . . .85
Dynamic characteristics: system clock timing .86
Dynamic characteristics: CPU interface block .86
Dynamic characteristics: high-speed source
electrical characteristics . . . . . . . . . . . . . . . . .86
Table 87: Dynamic characteristics: full-speed source
electrical characteristics . . . . . . . . . . . . . . . . .86
Table 88: Dynamic characteristics: low-speed source
electrical characteristics . . . . . . . . . . . . . . . . .87
Table 89: Register or memory write . . . . . . . . . . . . . . . .88
Table 90: Register or memory write . . . . . . . . . . . . . . . .88
Table 91: Register read . . . . . . . . . . . . . . . . . . . . . . . . . .89
Table 92: Register read . . . . . . . . . . . . . . . . . . . . . . . . . .89
Table 93: Memory read . . . . . . . . . . . . . . . . . . . . . . . . . .90
Table 94: Memory read . . . . . . . . . . . . . . . . . . . . . . . . . .90
Table 95: DMA read (single cycle) . . . . . . . . . . . . . . . . . .91
Table 96: DMA read (single cycle) . . . . . . . . . . . . . . . . . .91
Table 97: DMA write (single cycle) . . . . . . . . . . . . . . . . .92
Table 98: DMA write (single cycle) . . . . . . . . . . . . . . . . .92
Table 99: DMA read (multicycle burst) . . . . . . . . . . . . . .93
Table 100:DMA read (multicycle burst) . . . . . . . . . . . . . .93
Table 101:DMA write (multicycle burst) . . . . . . . . . . . . . .94
Table 102:DMA write (multicycle burst) . . . . . . . . . . . . . .94
Table 103:Suitability of surface mount IC packages for wave
and reflow soldering methods . . . . . . . . . . . . .97
Table 104:Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . .98
Table 105:Revision history . . . . . . . . . . . . . . . . . . . . . . . .99
Table 83:
Table 84:
Table 85:
Table 86:
continued >>
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
102 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
26. Figures
Fig 1.
Fig 2.
Fig 3.
Fig 4.
Fig 5.
Fig 6.
Fig 7.
Fig 8.
Fig 9.
Fig 10.
Fig 11.
Fig 12.
Fig 13.
Fig 14.
Fig 15.
Fig 16.
Fig 17.
Fig 18.
Fig 19.
Block diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Pin configuration (LQFP128). . . . . . . . . . . . . . . . .5
Internal hub. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Memory segmentation and access block
diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Adjusting analog overcurrent detection limit
(optional). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
ISP1760 power supply connection. . . . . . . . . . . .24
Most commonly used power supply connection. .25
Internal power-on reset timing. . . . . . . . . . . . . . .25
Clock with respect to the external power-on
reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
NextPTD traversal rule. . . . . . . . . . . . . . . . . . . . .57
USB source differential data-to-EOP transition skew
and EOP width. . . . . . . . . . . . . . . . . . . . . . . . . . .87
Register or memory write. . . . . . . . . . . . . . . . . . .88
Register read. . . . . . . . . . . . . . . . . . . . . . . . . . . .89
Memory read.. . . . . . . . . . . . . . . . . . . . . . . . . . . .90
DMA read (single cycle). . . . . . . . . . . . . . . . . . . .91
DMA write (single cycle). . . . . . . . . . . . . . . . . . . .92
DMA read (multicycle burst). . . . . . . . . . . . . . . . .93
DMA write (multicycle burst). . . . . . . . . . . . . . . . .94
Package outline (LQFP128). . . . . . . . . . . . . . . . .95
continued >>
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
103 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
27. Contents
1
2
3
3.1
4
5
6
6.1
6.2
7
7.1
7.2
7.2.1
7.2.2
7.3
7.3.1
7.3.2
7.3.3
7.3.4
7.3.5
7.4
7.5
7.6
7.7
7.8
7.9
8
8.1
8.1.1
8.1.2
8.1.3
8.1.4
8.2
8.2.1
8.2.2
8.2.3
8.2.4
8.2.5
8.2.6
8.2.7
8.2.8
8.2.9
General description . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Examples of a multitude of possible
applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Ordering information . . . . . . . . . . . . . . . . . . . . . 3
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Pinning information . . . . . . . . . . . . . . . . . . . . . . 5
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5
Functional description . . . . . . . . . . . . . . . . . . 12
ISP1760 internal architecture: Advanced Philips
Slave Host Controller and hub . . . . . . . . . . . . 12
Host Controller buffer memory block . . . . . . . 13
General considerations. . . . . . . . . . . . . . . . . . 13
Structure of the ISP1760 Host Controller
memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Accessing the ISP1760 Host Controller memory:
PIO and DMA . . . . . . . . . . . . . . . . . . . . . . . . . 16
PIO mode access—memory read cycle . . . . . 17
PIO mode access—memory write cycle. . . . . 17
PIO mode access—register read cycle . . . . . 18
PIO mode access—register write cycle . . . . . 18
DMA—read and write operations . . . . . . . . . . 18
Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Phase-Locked Loop (PLL) clock multiplier . . . 21
Power management . . . . . . . . . . . . . . . . . . . . 22
Overcurrent detection . . . . . . . . . . . . . . . . . . . 23
Power supply . . . . . . . . . . . . . . . . . . . . . . . . . 24
Power-on reset (POR) . . . . . . . . . . . . . . . . . . 25
Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
EHCI capability registers . . . . . . . . . . . . . . . . 28
CAPLENGTH register (R: 0000h). . . . . . . . . . 28
HCIVERSION register (R: 0002h) . . . . . . . . . 28
HCSPARAMS register (R: 0004h) . . . . . . . . . 28
HCCPARAMS register (R: 0008h) . . . . . . . . . 29
EHCI operational registers . . . . . . . . . . . . . . . 30
USBCMD register (R/W: 0020h). . . . . . . . . . . 30
USBSTS register (R/W: 0024h) . . . . . . . . . . . 31
USBINTR register (R/W: 0028h). . . . . . . . . . . 32
FRINDEX register (R/W: 002Ch) . . . . . . . . . . 33
CTRLDSSEGMENT register (R/W: 0030h) . . 34
CONFIGFLAG register (R/W: 0060h) . . . . . . . 34
PORTSC1 register (R/W: 0064h) . . . . . . . . . . 35
ISO PTD Done Map register (R: 0130h). . . . . 36
ISO PTD Skip Map register (R/W: 0134h) . . . 37
8.2.10
ISO PTD Last PTD register (R/W: 0138h) . . . 37
8.2.11
INT PTD Done Map register (R: 0140h). . . . . 37
8.2.12
INT PTD Skip Map register (R/W: 0144h) . . . 38
8.2.13
INT PTD Last PTD register (R/W: 0148h) . . . 38
8.2.14
ATL PTD Done Map register (R: 0150h) . . . . 38
8.2.15
ATL PTD Skip Map register (R/W: 0154h) . . . 38
8.2.16
ATL PTD Last PTD register (R/W: 0158h) . . . 39
8.3
Configuration registers . . . . . . . . . . . . . . . . . . 39
8.3.1
HW Mode Control register (R/W: 0300h) . . . . 39
8.3.2
Chip ID register (R: 0304h) . . . . . . . . . . . . . . 41
8.3.3
Scratch register (R/W: 0308h) . . . . . . . . . . . . 41
8.3.4
SW Reset register (R/W: 030Ch) . . . . . . . . . . 41
8.3.5
DMA Configuration register (R/W: 0330h) . . . 42
8.3.6
Buffer Status register (R/W: 0334h) . . . . . . . . 43
8.3.7
ATL Done Timeout register (R/W: 0338h) . . . 44
8.3.8
Memory register (R/W: 033Ch) . . . . . . . . . . . 44
8.3.9
Edge Interrupt Count register (R/W: 0340h) . 45
8.3.10
DMA Start Address register (W: 0344h) . . . . 46
8.3.11
Power Down Control register (R/W: 0354h) . . 46
8.3.12
Port 1 Control register (R/W: 0374h) . . . . . . . 48
8.4
Interrupt registers . . . . . . . . . . . . . . . . . . . . . . 50
8.4.1
Interrupt register (R/W: 0310h) . . . . . . . . . . . 50
8.4.2
Interrupt Enable register (R/W: 0314h) . . . . . 51
8.4.3
ISO IRQ Mask OR register (R/W: 0318h) . . . 53
8.4.4
INT IRQ Mask OR register (R/W: 031Ch) . . . 53
8.4.5
ATL IRQ Mask OR register (R/W: 0320h) . . . 53
8.4.6
ISO IRQ Mask AND register (R/W: 0324h) . . 54
8.4.7
INT IRQ Mask AND register (R/W: 0328h) . . 54
8.4.8
ATL IRQ Mask AND register (R/W: 032Ch) . . 54
9
Philips Transfer Descriptor. . . . . . . . . . . . . . . 55
9.1
High-speed bulk IN and OUT, Queue Head
Asynchronous (QHA) (patent-pending) . . . . . 58
9.2
High-speed isochronous IN and OUT,
isochronous Transfer Descriptor (iTD)
(patent-pending). . . . . . . . . . . . . . . . . . . . . . . 62
9.3
High-speed interrupt IN and OUT, Queue Head
Periodic (QHP) (patent-pending) . . . . . . . . . . 66
9.4
Start and complete split for bulk, Queue Head
Asynchronous Start Split and Start Complete
(QHA-SS/SC) (patent-pending) . . . . . . . . . . . 70
9.5
Start and complete split for isochronous, Split
isochronous Transfer Descriptor (SiTD)
(patent-pending). . . . . . . . . . . . . . . . . . . . . . . 74
9.6
Start and complete split for interrupt
(patent-pending). . . . . . . . . . . . . . . . . . . . . . . 78
10
Power consumption . . . . . . . . . . . . . . . . . . . . 82
11
Limiting values . . . . . . . . . . . . . . . . . . . . . . . . 83
continued >>
9397 750 13257
Product data sheet
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Rev. 01 — 8 November 2004
104 of 105
ISP1760
Philips Semiconductors
Embedded Hi-Speed USB host controller
12
13
14
14.1
14.1.1
14.1.2
14.1.3
14.2
14.2.1
14.2.2
14.2.3
14.2.4
15
16
16.1
16.2
16.3
16.4
16.5
17
18
19
20
21
22
23
24
Recommended operating conditions. . . . . . . 83
Static characteristics. . . . . . . . . . . . . . . . . . . . 84
Dynamic characteristics . . . . . . . . . . . . . . . . . 86
PIO timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Register or memory write . . . . . . . . . . . . . . . . 88
Register read . . . . . . . . . . . . . . . . . . . . . . . . . 89
Memory read . . . . . . . . . . . . . . . . . . . . . . . . . 90
DMA timing . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Single cycle: DMA read . . . . . . . . . . . . . . . . . 91
Single cycle: DMA write . . . . . . . . . . . . . . . . . 92
Multicycle: DMA read . . . . . . . . . . . . . . . . . . . 93
Multicycle: DMA write . . . . . . . . . . . . . . . . . . . 94
Package outline . . . . . . . . . . . . . . . . . . . . . . . . 95
Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Introduction to soldering surface mount
packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 96
Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 96
Manual soldering . . . . . . . . . . . . . . . . . . . . . . 97
Package related soldering information . . . . . . 97
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 98
References . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Revision history . . . . . . . . . . . . . . . . . . . . . . . . 99
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 100
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Contact information . . . . . . . . . . . . . . . . . . . 100
© Koninklijke Philips Electronics N.V. 2004
All rights are reserved. Reproduction in whole or in part is prohibited without the prior
written consent of the copyright owner. The information presented in this document does
not form part of any quotation or contract, is believed to be accurate and reliable and may
be changed without notice. No liability will be accepted by the publisher for any
consequence of its use. Publication thereof does not convey nor imply any license under
patent- or other industrial or intellectual property rights.
Date of release: 8 November 2004
Document number: 9397 750 13257
Published in The Netherlands