L5991 L5991A PRIMARY CONTROLLER WITH STANDBY CURRENT-MODE CONTROL PWM SWITCHING FREQUENCY UP TO 1MHz LOW START-UP CURRENT (< 120µA) HIGH-CURRENT OUTPUT DRIVE SUITABLE FOR POWER MOSFET (1A) FULLY LATCHED PWM LOGIC WITH DOUBLE PULSE SUPPRESSION PROGRAMMABLE DUTY CYCLE 100%AND 50% MAXIMUM DUTY CYCLE LIMIT STANDBY FUNCTION PROGRAMMABLE SOFT START PRIMARY OVERCURRENT FAULT DETECTION WITH RE-START DELAY PWM UVLO WITH HYSTERESIS IN/OUT SYNCHRONIZATION LATCHED DISABLE INTERNAL 100ns LEADING EDGE BLANKING OF CURRENT SENSE PACKAGE: DIP16 AND SO16 MULTIPOWER BCD TECHNOLOGY DIP16 SO16 ORDERING NUMBERS: L5991/L5991A (DIP16) L5991D/L5991AD (SO16) line or DC-DC power supply applications using a fixed frequency current mode control. Based on a standard current mode PWM controller this device includes some features such as programmable soft start, IN/OUT synchronization, disable (to be used for over voltage protection and for power management), precise maximum Duty Cycle Control, 100ns leading edge blanking on current sense, pulse by pulse current limit, overcurrent protection with soft start intervention, and Standby function for oscillator frequency reduction when the converter is lightly loaded. DESCRIPTION This primary controller I.C., developed in BCD60II technology, has been designed to implement off BLOCK DIAGRAM SYNC 1 RCT 2 VCC DC-LIM 15 VREF 8 4 TIMING 25V + 3 DC 14 - DIS Vref + 15V/10V T PWM UVLO - 9 DIS VC + 2.5V 13V S BLANKING 10 OUT Q R PWM OVER CURRENT ISEN 13 1.2V SS FAULT SOFT-START + VREF VREF OK CLK DIS STAND-BY - 7 + 2.5V 5 E/A - 2R 1V PGND ST-BY VFB R 12 SGND August 1999 11 16 6 COMP D97IN725A 1/23 L5991 - L5991A ABSOLUTE MAXIMUM RATINGS Symbol VCC IOUT Ptot Tj Tstg Parameter Supply Voltage (ICC < 50mA) (*) Output Peak Pulse Current Analog Inputs & Outputs (6,7) Analog Inputs & Outputs (1,2,3,4,5,15,14, 13, 16) Power Dissipation @ Tamb = 70°C (DIP16) @ Tamb = 50°C (SO16) Junction Temperature, Operating Range Storage Temperature, Operating Range Value selflimit 1.5 -0.3 to 8 -0.3 to 6 1 0.83 -40 to 150 -55 to 150 Unit V A V V W W °C °C Value 80 120 °C/W °C/W (*) maximum package power dissipation limits must be observed PIN CONNECTION SYNC 1 16 ST-BY RCT 2 15 DC-LIM DC 3 14 DIS VREF 4 13 ISEN VFB 5 12 SGND COMP 6 11 PGND SS 7 10 OUT V CC 8 9 VC THERMAL DATA Symbol Rth j-amb Parameter Thermal Resistance Junction -Ambient (DIP16) Thermal Resistance Junction -Ambient (SO16) Unit PIN FUNCTIONS N. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Name SYNC RCT DC VREF VFB COMP SS VCC VC OUT PGND SGND ISEN DIS DC-LIM 16 ST-BY 2/23 Function Synchronization. A synchronization pulse terminates the PWM cycle and discharges Ct Oscillator pin for external CT, RA, RB components Duty Cycle control 5.0V +/-1.5% reference voltage @ 25°C Error Amplifier Inverting input Error Amplifier Output Soft start pin for external capacitor Css Supply for internal ”Signal” circuitry Supply for Power section High current totem pole output Power ground Signal ground Current sense Disable. It must never be left floating. TIE to SGND if not used. Connecting this pin to Vref, DC is limited to 50%. If it is left floating or grounded no limitation is imposed Standby. Connect a resistor to RCT. Connect to VREF or floating if not used. L5991 - L5991A ELECTRICAL CHARACTERISTICS (VCC = 15V; Tj = 0 to 105°C; RT = 13.3kΩ (*) CT = 1nF; unless otherwise specified.) Symbol Parameter REFERENCE SECTION Output Voltage VREF Line Regulation Load Regulation Temperature Stability TS Total Variation Short Circuit Current IOS Power Down/UVLO OSCILLATOR SECTION Initial Accuracy Duty Cycle Duty Cycle Accuracy Oscillator Ramp Peak Oscillator Ramp Valley ERROR AMPLIFIER SECTION Input Bias Current Input Voltage VI Open Loop Gain GOPL SVR Supply Voltage Rejection Output Low Voltage V OL Output High Voltage VOH Output Source Current IO Output Sink Current Unit Gain Bandwidth Slew Rate SR PWM CURRENT SENSE SECTION Input Bias Current Ib Maximum Input Signal IS Delay to Output Gain Fault Threshold Voltage Vt SOFT START SECTION SS Charge Current ISSC SS Discharge Current ISSD SS Saturation Voltage VSSSAT SS Clamp Voltage VSSCLAMP LEADING EDGE BLANKING Internal Masking Time OUTPUT SECTION Output Low Voltage V OL Output High Voltage VOH VOUT CLAMP Output Clamp Voltage Collector Leakage Test Condition Min. Typ. Max. Unit Tj = 25°C; IO = 1mA VCC = 12 to 20V; Tj = 25°C IO = 1 to 10mA; Tj = 25°C 4.925 5.075 10 10 Line, Load, Temperature Vref = 0V VCC = 6V; Isink = 0.5mA 4.80 30 5.0 2.0 2.0 0.4 5.0 0.2 5.130 150 0.5 V mV mV mV/°C V mA V 95 100 105 kHz 93 100 107 kHz 46.5 50 53.5 kHz 0 0 % % % % % V V pin 15 = Vref; Tj = 25°C Vcomp = 4.5V pin 15 = Vref; VCC = 12 to 20V Vcomp = 4.5V pin 15 = Vref; VCC = 12 to 20V Vcomp = 2V pin 3 = 0,7V, pin 15 = VREF pin 3 = 0.7V, pin 15 = OPEN pin 3 = 3.2V, pin 15 = VREF pin 3 = 3.2V, pin 15 = OPEN pin 3 = 2.79V, pin 15 = OPEN VFB to GND VCOMP = VFB VCOMP = 2 to 4V VCC = 12 to 20V Isink = 2mA Isou rce = 0.5mA, VFB = 2.3V VCOMP > 4V, V FB = 2.3V VCOMP = 1.1V, V FB = 2.7V Isen = 0 VCOMP = 5V Tj = 25°C VSS = 0.6V Tj = 25°C DC = 0% IO = 250mA IO = 20mA; VCC = 12V IO = 200mA; VCC = 12V IO = 5mA; VCC = 20V VCC = 20V VC = 24V 47 93 75 2.8 0.75 2.42 60 80 3.0 0.9 85 3.2 1.05 0.2 2.5 90 85 3.0 2.58 1.1 5 0.5 2 1.7 6 1.3 6 4 8 2.5 µA V dB dB V V mA mA MHz V/µs 2.85 1.1 3 1.0 70 3 1.2 15 1.08 100 3.15 1.3 µA V ns V/V V 14 5 20 10 26 15 0.6 7 µA µA V V 100 ns 0.92 1.0 10 9 10.5 10 13 2 20 V V V V µA (*) RT = RA//RB , RA = RB = 27kΩ, see Fig. 22. 3/23 L5991 - L5991A ELECTRICAL CHARACTERISTICS (continued.) Symbol Parameter OUTPUT SECTION Fall Time Test Condition C O = 1nF C O = 2.5nF C O = 1nF C O = 2.5nF VCC = VC = 0 to VCCON Isink = 10mA Rise Time UVLO Saturation SUPPLY SECTION Startup voltage VCCON Vhys UVLO Hysteresis IS Start Up Current Iop Iq Operating Current Quiescent Current 14 7.8 9 7 4.5 0.5 40 Before Turn-on at: VCC = VC = VCCON -0.5V CT = 1nF, R T = 13.3kΩ, CO =1nF (After turn on), CT = 1nF, R T = 13.3kΩ, CO =0nF I8 = 20mA Zener Voltage VZ STANDBY FUNCTION VREF-VST-BY Standby Threshold VT1 Typ. Max. Unit 20 35 50 70 60 ns ns ns ns V 100 1.0 L5991 L5991A L5991 L5991A L5991 L5991A Minimum Operating Voltage VCCOFF Min. 21 IST-BY = 2mA Vcomp Falling Vcomp Rising 15 8.4 10 7.6 5 0.8 75 16 9 11 8.2 120 V V V V V V µA 9 7.0 13 10 mA mA 25 30 V 45 2.5 4.0 mV V V 7 V mA SYNCHRONIZATION SECTION V1 I1 Clock Amplitude Clock Source Current V1 Sync Pulse Master Operation ISOURCE = 0.8mA Vclock = 3.5V Slave Operation Low Level High Level VSYNC = 3.5V Sync Pulse Current I1 OVER CURRENT PROTECTION Fault Threshold Voltage Vt DISABLE SECTION Shutdown threshold Shutdown Current ISH 4 3 V V mA 1.1 1.2 1.3 V 2.4 2.5 330 2.6 V µA VCC = 15V Figure 1. L5991 - Quiescent current vs. input voltage. (X = 7.6V and Y= 8.4V for L5991A) 1 3.5 0.5 Figure 2. L5991 - Quiescent current vs. input voltage (after disable). (X = 7.6V and Y= 8.4V for L5991A) Iq [m A ] 30 350 V 1 4 = 0, P in 2 = ope n T j = 2 5 °C 20 300 8 250 6 200 4 150 0 .2 0 .1 5 V 14 = Vref T j = 2 5 °C 100 0 .1 X 0 .0 5 0 4 8 12 16 V c c [V ] X 50 Y 0 0 4/23 Iq [µ A ] 20 24 28 0 4 8 Y 12 16 V cc [V ] 20 24 L5991 - L5991A Figure 3. Quiescent current vs. input voltage. Figure 4. Quiescent current vs. input voltage and switching frequency. Iq [m A ] 9 .0 Iq [mA] 36 V 1 4 = 0 , V 5 = V re f C o = 1 n F, T j = 2 5 °C 30 R t = 4 .5 K o h m ,T j = 2 5 °C 8 .5 DC = 0% 1M hz 24 5 00K hz 300K hz 8 .0 1M Hz 18 500KHz 100K hz 12 3 00 K Hz 7 .5 1 0 0K Hz 6 0 7 .0 8 10 12 14 16 18 V c c [V ] 20 22 24 8 10 12 14 16 V cc [ V ] 18 20 22 Figure 5. Quiescent current vs. input voltage and switching frequency. Figure 6. Reference voltage vs. load current. Iq [mA] 36 Vref [V] 5.1 Co= 1nF, Tj = 25°C 30 DC = 100% 24 1MHz 18 500KHz Vcc=15V 5.05 Tj = 25°C 5 300KHz 12 4.95 100KHz 6 4.9 0 0 8 10 12 14 16 Vcc [V] 18 20 5 10 22 15 20 25 Iref [mA] Figure 7. Vref vs. junction temperature. Figure 8. Vref vs. junction temperature. Vref [V]) Vref [V] 5.1 5.1 Vcc = 15V Vcc = 15V 5.05 5.05 Iref= 20mA Iref = 1mA 5 5 4.95 4.95 4.9 -50 -25 0 25 50 Tj (°C) 75 100 125 150 4.9 -50 -25 0 25 50 Tj (°C) 75 100 125 150 5/23 L5991 - L5991A Figure 9. Vref SVRR vs. switching frequency. Figure 10. Output saturation. Vsat = V SVRR (dB) [V] 10 16 Vcc = Vc = 15V Vcc=15V 120 14 Vp-p=1V Tj = 25°C 12 80 10 40 8 6 0 1 10 100 1000 fsw (Hz) 0 10000 Figure 11. Output saturation. 0.4 0.6 0.8 Isource [A] 1 1.2 Figure 12. UVLO Saturation V sat = V10 [V] Ipin10 [mA] 2.5 50 2 30 1 20 0.5 10 0 0.2 0.4 Vcc < Vccon beforeturn-on 40 Vcc = Vc = 15V T j = 25°C 1.5 0 0.2 0.6 0.8 1 1.2 0 0 200 400 Isink [A ] Figure 13. Timingresistor vs.switchingfrequency. 1,000 1,200 1,400 Figure 14. Switching frequency vs. temperature. fsw (KHz) fsw (KHz) 5000 320 Vcc 600 800 Vpin10 [mV] = 15V, V15 =0V 2000 R t= 4.5Kohm, C t = 1nF Tj = 25°C 1000 310 Vcc = 15V, V15=Vref 500 100pF 200 300 220pF 100 470pF 50 20 290 1 nF 2.2nF 5 .6nF 10 10 20 Rt (kohm) 6/23 30 40 280 -50 -25 0 25 50 Tj (°C) 75 100 125 150 L5991 - L5991A Figure 15. Switching frequency vs. temperature. Figure 16. Dead time vs Ct. fsw (KHz) 320 Dead time [ns] 1,500 Rt= 4.5Kohm, Ct = 1nF 310 Rt =4.5Kohm V15 = 0V Vcc = 15V, V15= 0 1,200 900 300 V15 = Vref 600 290 300 280 -50 -25 0 25 50 75 100 125 150 2 4 6 8 Timing capacitor Ct [nF] Tj (°C) Figure 17. Maximum Duty Cycle vs Vpin3. 10 Figure18.Delayto outputvs junctiontemperature. DC Control Voltage Vpin3 [V] 3.5 Delay to output (ns) 42 V15 = 0V V15 = Vref 40 3 38 2.5 36 34 2 Rt = 4.5Kohm, 32 PIN10 = OPEN 1V pulse on PIN13 Ct = 1nF 1.5 30 1 0 10 20 30 40 50 60 70 Duty Cycle [%] 80 90 100 28 -50 -25 0 25 50 75 100 125 150 Tj (°C) Figure 19. E/A frequency response. G [dB] Phase 140 150 120 100 100 80 50 60 0 40 20 0.01 0.1 1 10 100 f (KHz) 1000 10000 100000 7/23 L5991 - L5991A STANDBY FUNCTION The standby function, optimized for flyback topology, automatically detects a light load condition for the converter and decreases the oscillator frequency on that occurrence. The normal oscillation frequency is automatically resumed when the output load builds up and exceeds a defined threshold. This function allows to minimize power losses related to switching frequency, which represent the majority of losses in a lightly loaded flyback, without giving up the advantages of a higher switching frequency at heavy load. This is accomplished by monitoring the output of the Error Amplifier (VCOMP) that depends linearly on the peak primary current, except for an offset. If the the peak primary current decreases (as a result of a decrease of the power demanded by the load) and VCOMP falls below a fixed threshold (VT1), the oscillator frequency will be set to a lower value (fSB). When the peak primary current increases and VCOMP exceeds a second threshold (VT2) the oscillator frequency is set to the normal value (fosc). An appropriate hysteresis (VT2-VT1) prevents undesired frequency change when power is such that VCOMP moves close to the threshold. This operation is shown in fig. 20. Both the normal and the standby frequency are externally programmable. VT1 and VT2 are internally fixed but it is possible to adjust the thresholds in terms of input power level. Figure 20. Standby dynamic operation. APPLICATION INFORMATION Detailed Pin Function Description Pin 1. SYNC (In/Out Synchronization). This function allows the IC’s oscillator either to synchronize other controllers (master) or to be synchronized to an external frequency (slave). As a master, the pin delivers positive pulses during the falling edge of the oscillator (see pin 2). In slave operation the circuit is edge triggered. Refer to fig. 22 to see how it works. When several IC work in parallel no master-slave designation is needed because the fastest one becomes auto- Pin 2. RCT (Oscillator). Two resistors (RA and RB) and one capacitor (CT), connected as shown in fig. 22, allow to set separately the operating frequency of the oscillator in normal operation (fosc) and in standby mode (fSB). CT is charged from Vref through RA and RB in normal operation (STANDBY = HIGH), through RA only in standby ( STANDBY = LOW). See pin 16 description to see how the STANDBY signal is generated. When the voltage on CT reaches 3V, the capacitor is quickly internally discharged. As the voltage has dropped to 1V it starts being charged again. Pin fos c Normal operation PNO fSB PSB Stand-by 1 VT1 2 VT2 3 4 VCOMP matically the master. During the ramp-up of the oscillator the pin is pulled low by a 600µA internal sink current generator. During the falling edge, that is when the pulse is released, the 600µA pull-down is disconnected. The pin becomes a generator whose source capability is typically 7mA (with a voltage still higher than 3.5V). In fig. 21, some practical examples of synchronizing the L5991 are given. Since the device automatically diminishes its operating frequency under light load conditions, it is reasonable to suppose that synchronization will refer to normal operation and not to standby. Figure 21. Synchronizing the L5991. RA RB SYNC 1 SYNC ST-BY 16 L5991 4 VREF 2 RA RCT L5991 2 17 (a) 16 L5991 (SLAVE) 1 4 SYNC 18 2 VREF RB RA ROSC COSC CT (b) 4 RCT VREF RCT RCT CT 8/23 ST-BY L4981A (MASTER) 16 1 2 L5991 1 (MASTER) 16 RB L4981A (SLAVE) SYNC SYNC 16 17 18 ST-BY ROSC CT D97IN728A (c) COSC L5991 - L5991A Figure 22. Oscillator and synchronization internal schematic. SYNC VREF 1 4 R1 D CLAMP R R3 RA RCT 600µA R2 + 2 Q CLK D1 RB CT 50Ω ST-BY 16 STANDBY D97IN729A The oscillation frequency can be established with the aid of the diagrams of fig. 13, where RT will be intended as the parallel of RA and RB in normal operation and RT = RA in standby, or considering the following approximate relationships: fosc ≅ 1 CT ⋅ (0.693 ⋅ (RA // RB) + KT (1), from fig. 13 or resulting from (1) and (2). To prevent the oscillator frequency from switching back and forth from fosc to fSB, the ratio fosc / fSB must not exceed 5.5. If during normal operation the IC is to be synchronized to an external oscillator, RA, RB and CT should be selected for a fosc lower than the master frequency in any condition (typically, 10-20% ), depending also on the tolerance of the parts. which gives the normal operating frequency, and: fSB ≅ 1 CT ⋅ (0.693 ⋅ RA + KT) (2), which gives the standby frequency, that is the one the converter will operate at when lightly loaded. In the above expressions, RA // RB means: RA ⋅ RB RA//RB = , RA + RB while KT is defined as: 90 V15 = VREF (3), KT = 160 V15 = GND/OPEN and is related to the duration of the falling-edge of the sawtooth: Td ≈ 30 ⋅ 10−9 + KT ⋅ CT (4). Td is also the duration of the sync pulses delivered at pin 1 and defines the upper extreme of the duty cycle range, Dx (see pin 15 for DX definition and calculation) since the output is held low during the falling edge. In case V15 is connected to VREF, however, the switching frequency will be a half the values taken Pin 3. DC (Duty Cycle Control). By biasing this pin with a voltage between 1 and 3 V it is possible to set the maximum duty cycle between 0 and the upper extreme Dx (see pin 15). If Dmax is the desired maximum duty cycle, the voltage V3 to be applied to pin 3 is: V3 = 5 - 2(2-Dmax) (5) Dmax is determined by internal comparison between V3 and the oscillator ramp (see fig. 23), thus in case the device is synchronized to an external frequency fext (and therefore the oscillator amplitude is reduced), (5) changes into: Dmax V3 = 5 − 4 ⋅ exp − (6) RT ⋅ CT ⋅ fext A voltage below 1V will inhibit the driver output stage. This could be used for a not-latched device disable, for example in case of overvoltage protection (see application ideas). If no limitation on the maximum duty cycle is required (i.e. DMAX = DX), the pin has to be left floating. An internal pull-up (see fig. 23) holds the voltage above 3V. Should the pin pick up noise (e.g. 9/23 L5991 - L5991A during ESD tests), it can be connected to VREF through a 4.7kΩ resistor. Figure 23. Duty cycle control. VREF 4 DC 3 R1 RA 3µA 23K R2 28K ST-BY RB RCT 3 ⋅ Rsense ⋅ IQpk ⋅ Css (7) ISSC where Rsense is the current sense resistor (see pin 13) and IQpk is the switch peak current (flowing through Rsense), which depends on the output load. Usually, CSS is selected for a TSS in the order of milliseconds. As mentioned before, the soft-start intervenes also in case of severe overload or short circuit on the output. Referring to fig. 24, pulse-by-pulse current limitation is somehow effective as long as Tss ≅ 16 2 + TO PWM LOGIC - CT D97IN727A Pin 4. VREF (Reference Voltage). The device is provided with an accurate voltage reference (5V±1.5%) able to deliver some mA to an external circuit. A small film capacitor (0.1 µF typ.), connected between this pin and SGND, is recommended to ensure the stability of the generator and to prevent noise from affecting thereference. Before device turn-on, this pin has a sink current capability of 0.5mA. Pin 5. VFB (Error Amplifier Inverting Input). The feedback signal is applied to this pin and is compared to the E/A internal reference (2.5V). The E/A output generates the control voltage which fixes the duty cycle. The E/A features high gain-bandwidth product, which allows to broaden the bandwidth of the overall control loop, high slew-rate and current capability, which improves its large signal behavior. Usually the compensation network, which stabilizes the overall control loop, is connected between this pin and COMP (pin 6). Pin 6. COMP (Error Amplifier Output). Usually, this pin is used for frequency compensation and the relevant network is connected between this pin and VFB (pin 5). Compensation networks towards ground are not possible since the L5991 E/A is a voltage mode amplifier (low output impedance). See application ideas for some example of compensation techniques. It is worth mentioning that the calculation of the part values of the compensation network must take the standby frequency operation into account. In particular, this means that the open-loop crossover frequency must not exceed fSB/4 ÷ fSB/5. The voltage on pin 6 is monitored in order to re10/23 duce the oscillator frequency when the converter is lightly loaded (standby). Pin 7. SS (Soft-Start). At device start-up, a capacitor (Css) connected between this pin and SGND (pin 12) is charged by an internal current generator, ISSC, up to about 7V. During this ramp, the E/A output is clamped by the voltage across Css itself and allowed to rise linearly, starting from zero, up to the steady-state value imposed by the control loop. The maximum time interval during which the E/A is clamped, referred to as soft-start time, is approximately: Figure 24. Regulation characteristic and related quantities. VOUT IQpk A D.C.M. C.C.M. 1-2 ·IQpk IQpk(max) B C TON D TON(min) D97IN495 ISHORT IOUT(max) IOUT the ON-time of the power switch can be reduced (from A to B). After the minimum ON-time is reached (from B onwards) the current is out of control. To prevent this risk, a comparator trips an overcurrent handling procedure, named ’hiccup’ mode operation, when a voltage above 1.2V (point C) is detected on current sense input (ISEN, pin 13). Basically, the IC is turned off and then soft-started as long as the fault condition is detected. As a result, the operating point is moved abruptly to D, creating a foldback effect. Fig. 25 illustrates the operation. The oscillation frequency appearing on the softstart capacitor in case of permanent fault, referred to as ’hiccup” period, is approximately given by: 1 Thic ≅ 4.5 ⋅ ISSC + 1 ⋅ Css (8) ISSD L5991 - L5991A Since the system tries restarting each hiccup cycle, there is not any latchoff risk. ”Hiccup” keeps the system in control in case of short circuits but does not eliminate power components overstress during pulse-by-pulse limitation (from A to C). Other external protection circuits are needed if a better control of overloads is required. MOS. At turn-on the gate resistance is Rg + Rg’, at turn-off is Rg only. Figure 26. Turn-on and turn-off speeds adjustment. Rg’ VCC Pin 8. VCC (Controller Supply). This pin supplies the signal part of the IC. The device is enabled as VCC voltage exceeds the start threshold and works as long as the voltage is above the UVLO threshold. Otherwise the device is shut down and the current consumption is extremely low (<150µA). This is particularly useful for reducing the consumption of the start-up circuit (in the simplest case, just one resistor), which is one of the most significant contributions to power losses in standby. An internal Zener limits the voltage on VCC to 25V. The IC current consumption increases considerably if this limit is exceeded. A small film capacitor between this pin and SGND (pin 12), placed as close as possible to the IC, is recommended to filter high frequency noise. Pin 9. VC (Supply of the Power Stage). It supplies the driver of the external switch and therefore absorbs a pulsed current. Thus it is recommended to place a buffer capacitor (towards PGND, pin 11, as close as possible to the IC) able to sustain these current pulses and in order to avoid them inducing disturbances. This pin can be connected to the buffer capacitor directly or through a resistor, as shown in fig. 26, to control separately the turn-on and turn-off speed of the external switch, typically a Power- Rg(ON)=Rg+Rg’ Rg(OFF)=Rg VC 9 8 13V 10 DRIVE & CONTROL OUT L5991 D97IN726 Rg 11 PGND Pin 10. OUT (Driver Output). This pin is the output of the driver stage of the external power switch. Usually, this will be a PowerMOS, although the driver is powerful enough to drive BJT’s (1.6A source, 2A sink, peak). The driver is made up of a totem pole with a highside NPN Darlington and a low-side VDMOS, thus there is no need of an external diode clamp to prevent voltage from going below ground. An internal clamp limits the voltage delivered to the gate at 13V. Thus it is possible to supply the driver (Pin 9) with higher voltages without any risk of damage for the gate oxide of the external MOS. The clamp does not cause any additional increase of power dissipation inside the chip since the current peak of the gate charge occurs when the gate voltage is few volts and the clamp is not active. Besides, no current flows when the gate voltage is 13V, steady state. Under UVLO conditions an internal circuit (shown Figure 25. Hiccup mode operation. IOUT SHORT ISEN FAULT SS 5V 7V 0.5V Thic D98IN986 time 11/23 L5991 - L5991A in fig.27) holds the pin low in order to ensure that the external MOS cannot be turned on accidentally. The peculiarity of this circuit is its ability to mantain the same sink capability (typically, 20mA @ 1V) from VCC = 0V up to the start-up threshold. When the threshold is exceeded and the L5991 starts operating, V REFOK is pulled high (refer to fig. 27) and the circuit is disabled. It is then possible to omit the ”bleeder” resistor (connected between the gate and the source of the MOS) ordinarily used to prevent undesired switching-on of the external MOS because of some leakage current. Pin 13. ISEN (Current Sense). This pin is to be connected to the ”hot” lead of the current sense resistor Rsense (being the other one grounded), to get a voltage ramp which is an image of the current of the switch (IQ). When this voltage is equal to: V13pk = IQpk ⋅ Rsense = VCOMP − 1.4 (9) 3 the conduction of the switch is terminated. To increase the noise immunity, a ”Leading Edge Blanking” of about 100ns is internally realized as shown in fig. 28. Because of that, the smoothing RC filter between this pin and Rsense could be removed or, at least, considerably reduced. Figure 27. Pull-Down of the output in UVLO. OUT 10 Pin 14. DIS (Device Disable). When the voltage on pin 14 rises above 2.5V the IC is shut down and it is necessary to pull VCC (IC supply voltage, pin 8) below the UVLO threshold to allow the device to restart. The pin can be driven by an external logic signal in case of power management, as shown in fig. 29. It is also possible to realize an overvoltage protection, as shown in the section ” Application Ideas”.If used, bypass this pin to ground with a filter capacitor to avoid spurious activation due to noise spikes. If not, it must be connected to SGND. VREFOK 12 SGND D97IN538 Pin 11. PGND (Power Ground). The current loop during the discharge of the gate of the external MOS is closed through this pin. This loop should be as short as possible to reduce EMI and run separately from signal currents return. Pin 15. DC-LIM (Maximum Duty Cycle Limit). The upper extreme, Dx, of the duty cycle range depends on the voltage applied to this pin. Approximately, Pin 12. SGND (Signal Ground). This ground references the control circuitry of the IC, so all the ground connections of the external parts related to control functions must lead to this pin. In laying out the PCB, care must be taken in preventing switched high currents from flowing through the SGND path. Dx ≅ RT (10) RT + 230 if DC-LIM is grounded or left floating. Instead, Figure 28. Internal LEB. 2V I 3V + 0 CLK ISEN 13 + FROM E/A PWM COMPARATOR TO PWM LOGIC - TO FAULT LOGIC + 1.2V 12/23 - OVERCURRENT COMPARATOR D97IN503 L5991 - L5991A Figure 29. Disable (Latched). and the output switching frequency will be halved with respect to the oscillator one because an internal T flip-flop (see block diagram) is activated. Fig. 30 shows the operation. The half duty cycle option speeds up the discharge of the timing capacitor CT (in order to get duty cycles as close to 50% as possible) so the oscillator frequency - with the same timing components will be slightly higher. DISABLE SIGNAL DIS 14 + D - R Q DISABLE C Pin 16. S-BY (Standby Function). The resistor RB, along with RA, sets the operating frequency of the oscillator in normal operation (fosc). In fact, as long as the STANDBY signal is high, the pin is internally connected to the reference voltage VREF by a N-channel FET (see fig. 31), so the timing capacitor CT is charged through RA and RB. When the STANDBY signal goes low the N-channel FET is turned off and the pin becomes floating. RB is 2.5V UVLO D97IN502 connecting DC-LIM to VREF (half duty cycle option), Dx will be set approximately at: RT (11) 2 ⋅ RT + 260 Figure 30. Half duty cycle option. Dx ≅ td V15=GND V5=V13=GND V2 DX = tc tc + td V10 tc td V15=VREF V5=V13=GND V2 DX = tc 2 ·tc + td V10 tc D97IN498 Figure 31. Standby function internal schematic and operation. ISEN COMP 13 6 + 2R R - OUT DRIVER R FB 10V 5 2.5 - + + 2.5/4 VREF STANDBY LEVEL SHIFT STANDBY BLOCK STANDBY 4 HIGH ST-BY 16 LOW RB 2 RCT RA CT VT1 2.5V V T2 4V VCOMP D97IN752B 13/23 L5991 - L5991A now disconnected and CT is charged through RA only. In this way the oscillator frequency (fSB) will be lower. Refer to pin 2 description to see how to calculate the timing components. Typical values for VT1 and VT2 are 2.5 V and 4V respectively. This 1.5V hysteresis is enough to prevent undesired frequency change up to a 5.5 to 1 fosc/ fSB ratio. The value of VT1 is such that in a discontinuous flyback the standby frequency is activated when the input power is about 13% of the maximum. If necessary, it is possible to decrease the power threshold below 13% by adding a DC offset (Vo) on the current sense pin (13, ISEN). This will also allow a frequency change greater than 5.5 to 1. The following equations,useful for design, apply: PinSB = 0.367 − Vo 1 ⋅ LP ⋅ ƒ osc ⋅ 2 Rsense 2 (12), 2 0.867 − Vo 1 PinNO = ⋅ LP ⋅ ƒ SB ⋅ 2 Rsense (13), 2 ƒ osc 0.867 − Vo < ƒ SB 0.367 − Vo (14), where PinSB is the input power below which the L5991 recognizes a light load and switches the oscillator frequency from ƒ osc to fSB, PinNO is the input power above which the L5991 switches back from ƒ SB to ƒ osc and Lp the primary inductance of the flyback transformer. Connect to Vref or leave open this pin when stand-by function is not used. 14/23 Layout hints Generally speaking a proper circuitboard layout is vital for correct operation but is not an easy task. Careful component placing, correct traces routing, appropriate traces widths and, in case of high voltages, compliance with isolation distances are the major issues. The L5991 eases this task by putting two pins at disposal for separate current returns of bias (SGND) and switch drive currents (PGND) The matter is complex and only few important points will be here reminded. 1) All current returns (signal ground, power ground, shielding, etc.) should be routed separately and should be connected only at a single ground point. 2) Noise coupling can be reduced by minimizing the area circumscribed by current loops. This applies particularly to loops where high pulsed currents flow. 3) For high current paths, the traces should be doubled on the other side of the PCB whenever possible: this will reduce both the resistance and the inductance of the wiring. 4) Magnetic field radiation (and stray inductance) can be reduced by keeping all traces carrying switched currents as short as possible. 5) In general, traces carrying signal currents should run far from traces carrying pulsed currents or with quickly swinging voltages. From this viewpoint, particular care should be taken of the high impedance points (current sense input, feedback input, ...). It could be a good idea to route signal traces on one PCB side and power traces on the other side. 6) Provide adequate filtering of some crucial points of the circuit, such as voltage references, IC’s supply pins, etc. 88 to 270 VAC C09 8.2nF 6800pF R9 24K R5 12K 5 7 16 2 4 Pin(W) Pout(W) 14 3.10 2.95 2 110 L5991 16 3.90 220 2.2nF R13 47K C11 R03 47K R01 3.3 9 4.40 270 6 11 12 13 10 8 R06 27 R12 330K R04 47K C03 220µF 400V BD01 88 C02 0.1µF VAC(V) D06 1N4148 LF01 D05 1N4937 R18 47K 3W C08 3.3nF R21 100 C05 100pF R11 1K R08 22 C04 47µF R10 0.22 D04 1N4148 R17 750K R16 750K 8 3 7 Q51 TL431 4N35 R54 1K Q01 STP6 NA60FI R07 47 C10 10nF 100V C54 220µF 100V D53 BYT11-600 R58 4.7K R53 4.7K R52 47 C55 1000µF 16V C61 0.056µF R55 300K VR51 100K C58 47µF 25V 10 D56 BYW100-100 11 C56 470µF 25V C57 470µF 25V 13 12 D55 BYW100-100 15 14 D54 BYW100-100 16 17 R19 4.7M R20 4.7M 18 D52 BYT13-800 1 R56 4.3K C59 0.01µF C52 100µF 250V D97IN730A C62 100µF 100V -15V 5W +15V 5W 6.3V 5W GND 80V 10W 180V 65W APPLICATION IDEAS Here follows a series of ideas/suggestions aimed at C06 C07 1µF C01 0.1µF F01 AC 250V T3.15A C11 4700pF 4KV C12 L5991 - L5991A either improving performance or solving common application problems of L5991 based supplies. Figure 32. Typical application circuit for computer monitors (90W). 15/23 16/23 47K Pout(W) 85 0.90 Pin(W) 5.6K 5.6K VAC(V) 330nF 3.3nF 22K 22V C02 0.1 µF 0.55 7 1 220 1.14 16 2 3 4 5.6K 0.93 110 1.1M 1.1M LF01 BC337 100nF 85 TO C01 265 Vac 0.1µF F01 AC 250V T1A 14 1.57 5 L5991 265 15 4.7K BD01 6 11 12 13 10 9 8 22 33K STK2N50 100µF 400V 2.2 D97IN618 470pF 470 470pF 1K 22 33µF/25V BAT46 10K 1N4937 BZW06-154 220 TL431 4N35 0.47 1/2 W STP4NA60 Naux N1 4.7M 4700pF 4KV 1K 2.7K N4 N3 N2 4.7M BYW100-200 0.022 µF BYW100-50 3.9K 470µF 16V 2 x 470µF 16V BYW98-100 4700pF 4KV 5.1K 2 x 330µF 35V 270K 5V / 0.5A GND 12V / 1.5A 28V / 0.7A L5991 - L5991A Figure 33. Typical application circuit for inkjet printers (40W). L5991 - L5991A Figure 34. Standby thresholds adjustment. SGND L5991 12 4 10 13 VREF ISEN R RA RSENSE OPTIONAL D97IN751A Figure 35. Isolated MOSFET Drive & Current Transformer Sensing in 2-switch Topologies. VIN ISOLATION BOUNDARY VC 9 OUT 10 L5991 ISEN 13 12 PGND 11 SGND D97IN761 Figure 36. Low consumption start-up. VIN 2.2MΩ 33KΩ STD1NB50-1 T VCC VREF 20V 47KΩ 4 SELF-SUPPLY WINDING 8 L5991 12 11 D97IN762B Figure 37. Bipolar transistor driver. VIN VCC 8 VC 9 10 13 L5991 OUT ISEN 11 PGND D97IN763 17/23 L5991 - L5991A Figure 38. Typical E/A compensation networks. + 2.5V From VO 1.3mA Ri VFB 5 Rd 2R + EA R Rf Cf COMP 6 12 SGND Error Amp compensation circuit for stabilizing any current-mode topology except for boost and flyback converters operating with continuous inductor current. From VO + 2.5V 1.3mA RP Ri CP VFB 5 - EA R Rf Cf Rd 2R + COMP 6 12 SGND D97IN507 Error Amp compensation circuit for stabilizing current-mode boost and flyback topologies operating with continuous inductor current. Figure 39. Feedback with optocoupler. VOUT 6 COMP L5991 5 TL431 VFB D97IN759 Figure 40. Slope compensation techniques. ST-BY VREF RB RSLOPE 4 RB RA RCT I ST-BY V REF 16 2 ISEN RSENSE I R 2 RSLOPE CSLOPE L5991 ISEN 12 SGND OPTIONAL RSENSE 13 L5991 12 12 SGND 13 ISEN OPTIONAL RSLOPE RSENSE SGND OPTIONAL D97IN760A 18/23 OUT CT L5991 13 10 RA RCT CT 16 4 L5991 - L5991A Figure 41. Protection against overvoltage/feedback disconnection (latched) RSTART RSTART VCC DIS VCC VZ 8 8 DIS L5991 14 L5991 14 12 11 SGND 12 2.2K 11 SGND PGND PGND D98IN905 D97IN754 Figure 42 Protection against overvoltage/feedback disconnection (not latched) Figure 43. Device shutdown on overcurrent RSTART Ipk max ≅ VREF 4 R1 VREF DC • 1- R2 R1 Ipk 14 L5991 8 R2 L5991 3 I DIS VCC 4 2.5 R SENSE 11 12 PGND 11 12 ISEN 13 RSENSE SGND OPTIONAL D97IN756A D97IN755A Figure 44. Constant power in pulse-by-pulse current limitation (flyback discontinuous) VIN 80 ÷ 400VDC Lp RFF 6 OUT RFF = 6·10 10 L5991 11 PGND 12 R·Lp RSENSE ISEN 13 R RSENSE SGND D97IN757 Figure 45. Voltage mode operation. DC 3 10K COMP L5991 6 SGND 12 13 ISEN D97IN758A 19/23