M74HCT244 OCTAL BUS BUFFER WITH 3 STATE OUTPUTS (NON INVERTED) ■ ■ ■ ■ ■ ■ HIGH SPEED: tPD = 15 ns (TYP.) at VCC = 4.5V LOW POWER DISSIPATION: ICC = 4µA(MAX.) at TA=25°C COMPATIBLE WITH TTL OUTPUTS : VIH = 2V (MIN.) VIL = 0.8V (MAX) BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 6mA (MIN) PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 244 DESCRIPTION The 74HCT244 is an advanced high-speed CMOS OCTAL BUS BUFFER (3-STATE) fabricated with silicon gate C2MOS technology. G control input governs four BUS BUFFERs. DIP SOP TSSOP ORDER CODES PACKAGE TUBE DIP SOP TSSOP M74HCT244B1R M74HCT244M1R T&R M74HCT244RM13TR M74HCT244TTR All inputs are equipped with protection circuits against static discharge and transient excess voltage. PIN CONNECTION AND IEC LOGIC SYMBOLS August 2001 1/9 M74HCT244 INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN No SYMBOL 1 2, 4, 6, 8 9, 7, 5, 3 11, 13, 15, 17 18, 16, 14, 12 19 10 20 1G 1A1 to 1A4 2Y1 to 2Y4 2A1 to 2A4 Output Enable Input Data Inputs Data Outputs Data Inputs 1Y1 to 1Y4 Data Outputs 2G GND VCC NAME AND FUNCTION Output Enable Input Ground (0V) Positive Supply Voltage TRUTH TABLE INPUTS OUTPUT G An Yn L L H L H X L H Z X : Don’t Care Z : High Impedance ABSOLUTE MAXIMUM RATINGS Symbol VCC Parameter Supply Voltage Value Unit -0.5 to +7 V VI DC Input Voltage -0.5 to VCC + 0.5 V VO DC Output Voltage -0.5 to VCC + 0.5 ± 20 V mA IIK DC Input Diode Current IOK DC Output Diode Current ± 20 mA IO DC Output Current ± 35 mA ± 70 mA ICC or IGND DC VCC or Ground Current PD Power Dissipation Tstg Storage Temperature TL Lead Temperature (10 sec) 500(*) mW -65 to +150 °C 300 °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied (*) 500mW at 65 °C; derate to 300mW by 10mW/ °C from 65°C to 85°C RECOMMENDED OPERATING CONDITIONS Symbol VCC 2/9 Parameter Value Unit Supply Voltage 4.5 to 5.5 V VI Input Voltage 0 to VCC V VO Output Voltage 0 to VCC V Top Operating Temperature -55 to 125 °C tr, tf Input Rise and Fall Time (VCC = 4.5 to 5.5V) 0 to 500 ns M74HCT244 DC SPECIFICATIONS Test Condition Symbol VIH VIL VOH VOL II IOZ ICC ∆ ICC Parameter High Level Input Voltage Low Level Input Voltage Min. 4.5 to 5.5 4.5 to 5.5 4.5 Low Level Output Voltage 4.5 Input Leakage Current High Impedance Output Leakage Current Quiescent Supply Current Additional Worst Case Supply Current TA = 25°C VCC (V) High Level Output Voltage Value Typ. Max. 2.0 -40 to 85°C -55 to 125°C Min. Min. Max. 2.0 0.8 Max. 2.0 0.8 V 0.8 IO=-20 µA 4.4 4.5 4.4 4.4 IO=-6.0 mA 4.18 4.31 4.13 4.10 Unit V V IO=20 µA 0.0 0.1 0.1 0.1 IO=6.0 mA 0.17 0.26 0.33 0.40 V 5.5 VI = VCC or GND ± 0.1 ±1 ±1 µA 5.5 VI = VIH or VIL VO = VCC or GND ± 0.5 ±5 ± 10 µA 5.5 VI = VCC or GND 4 40 80 µA 5.5 Per Input pin VI = 0.5V or VI = 2.4V Other Inputs at VCC or GND 2.0 2.9 3.0 mA AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6ns) Test Condition Symbol Parameter tTLH tTHL Output Transition Time tPLH tPHL Propagation Delay Time tPLH tPHL Propagation Delay Time tPZL tPZH Output Enable Time tPLZ tPHZ Output Disable Time VCC (V) CL (pF) 4.5 Value TA = 25°C Min. -40 to 85°C -55 to 125°C Min. Min. Typ. Max. 50 7 12 15 18 4.5 4.5 4.5 4.5 4.5 4.5 50 150 50 150 50 150 15 21 15 21 17 23 22 30 25 33 30 38 28 38 31 41 38 48 33 45 38 50 45 57 4.5 50 16 30 38 45 RL = 1 KΩ RL = 1 KΩ Max. Unit Max. ns ns ns ns ns 3/9 M74HCT244 CAPACITIVE CHARACTERISTICS Test Condition Symbol Parameter CIN Input Capacitance COUT Output Capacitance Power Dissipation Capacitance (note 1) CPD Value TA = 25°C VCC (V) Min. Typ. Max. 5 10 -40 to 85°C -55 to 125°C Min. Min. Max. Unit Max. 10 10 pF 10 pF 31 pF 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = C PD x VCC x fIN + ICC/8 (per circuit) TEST CIRCUIT TEST SWITCH tPLH, tPHL Open tPZL, tPLZ VCC tPZH, tPHZ GND CL = 50pF/150pF or equivalent (includes jig and probe capacitance) R1 = 1KΩ or equivalent RT = ZOUT of pulse generator (typically 50Ω) 4/9 M74HCT244 WAVEFORM 1: PROPAGATION DELAY TIMES (f=1MHz; 50% duty cycle) WAVEFORM 2 :OUTPUT AND ENABLE TIMES (f=1MHz; 50% duty cycle) 5/9 M74HCT244 Plastic DIP-20 (0.25) MECHANICAL DATA mm. inch DIM. MIN. a1 0.254 B 1.39 TYP MAX. MIN. TYP. MAX. 0.010 1.65 0.055 0.065 b 0.45 0.018 b1 0.25 0.010 D 25.4 1.000 E 8.5 0.335 e 2.54 0.100 e3 22.86 0.900 F 7.1 0.280 I 3.93 0.155 L Z 3.3 0.130 1.34 0.053 P001J 6/9 M74HCT244 SO-20 MECHANICAL DATA mm. inch DIM. MIN. TYP A a1 MAX. MIN. TYP. 2.65 0.1 0.104 0.2 a2 MAX. 0.004 0.008 2.45 0.096 b 0.35 0.49 0.014 0.019 b1 0.23 0.32 0.009 0.012 C 0.5 0.020 c1 45° (typ.) D 12.60 13.00 0.496 0.512 E 10.00 10.65 0.393 0.419 e 1.27 0.050 e3 11.43 0.450 F 7.40 7.60 0.291 0.300 L 0.50 1.27 0.020 0.050 M S 0.75 0.029 8° (max.) PO13L 7/9 M74HCT244 TSSOP20 MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. A MIN. TYP. MAX. 1.2 A1 0.05 A2 0.8 b 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 D 6.4 6.5 6.6 0.252 0.256 0.260 E 6.2 6.4 6.6 0.244 0.252 0.260 E1 4.3 4.4 4.48 0.169 0.173 0.176 1 e 0.65 BSC K 0° L 0.45 A 0.0256 BSC 0.60 8° 0° 0.75 0.018 8° 0.024 0.030 A2 A1 b K e L E c D E1 PIN 1 IDENTIFICATION 1 0087225C 8/9 M74HCT244 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2001 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom © http://www.st.com 9/9