MAXIM MAX4899AEETE+

KIT
ATION
EVALU
E
L
B
A
AVAIL
19-0616; Rev 0; 7/06
USB 2.0 High-Speed, Fault-Tolerant 3:1, 4:1
Multiplexers
Features
The MAX4899E/MAX4899AE analog multiplexers combine the low on-capacitance (CON) and low on-resistance (RON) necessary for high-performance switching
applications. These devices are designed for USB 2.0
high-speed applications at 480Mbps. The MAX4899E/
MAX4899AE also handle all the requirements for USB
low- and full-speed signaling.
The MAX4899E is a dual 3:1 multiplexer whereas the
MAX4899AE is a dual 4:1 multiplexer. The MAX4899E/
MAX4899AE feature two digital inputs, C0 and C1, to control the analog signal path. Typical applications include
switching a USB connector between USB and other operations such as serial communications, audio, and video.
♦ Single 2.7V to 3.6V Power-Supply Voltage
An enable input (EN) is provided to disable all channels
and place the device into a high-impedance (off) state,
as well as reducing power consumption.
♦ Tiny 16-Pin, 3mm x 3mm, Lead-Free TQFN Package
♦ Low 4Ω (typ) On-Resistance (RON)
♦ -3dB Bandwidth: 425MHz
♦ Fault Tolerant to Meet Full USB 2.0 Specification
♦ COM_ Protected to ±15kV ESD Protection per
Human Body Model (MIL-STD-883; Method 3015)
♦ Low Operating Current (200µA), Ultra-Low
Quiescent Current (3.0µA max) in Standby Mode
♦ Low Threshold Eliminates the Need for
Translators in 1.8V Low Voltage Systems
The MAX4899E/MAX4899AE operate from a 2.7V to
3.6V power-supply voltage and are protected against
+5.5V shorts to COM A - and COM A +. In addition,
COMA+ and COMA- are normally connected to outside
circuitry and feature ±15kV ESD protection. The
MAX4899E/MAX4899AE are available in a 3mm x 3mm,
16-pin TQFN package and operate over the -40°C to
+85°C temperature range.
Eye Diagram
0.5
0.4
0.3
COMA+ AND COMA- (V)
Applications
Cell Phones
Digital Still Cameras
PDAs
Digital Video Cameras
0.2
0.1
0
-0.1
-0.2
-0.3
MPEG-4 Players
-0.4
-0.5
Portable GPS
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
TIME (ns)
Combination Products
KVM
NOTE: UI = 2.08ns
MASK = USB 2.0 HIGH SPEED
Pin Configurations appear at end of data sheet.
Ordering Information/Selector Guide
MUX CONFIGURATION
TOP MARK
PKG CODE
MAX4899EETE+
PART
16 TQFN-EP*
PIN-PACKAGE
DUAL 3:1
AEY
T1633-4
MAX4899AEETE+
16 TQFN-EP*
DUAL 4:1
AEZ
T1633-4
Note: All devices are specified over the -40°C to +85°C operating temperature range.
+Denotes lead-free package.
*EP = Exposed paddle.
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX4899E/MAX4899AE
General Description
MAX4899E/MAX4899AE
USB 2.0 High-Speed, Fault-Tolerant 3:1, 4:1
Multiplexers
ABSOLUTE MAXIMUM RATINGS
(All Voltages Referenced to GND.)
V+ .............................................................................-0.3V to +4V
QP, EN, C0, C1, (Note 1) ..........................................-0.3V to +4V
COMA+, COMA_, USB0+, USB0-, USB1+, USB1-, USB2+,
USB2-, USB3+, USB3- ......................................-0.3V to +5.5V
Continuous Current (COMA_ to USB_) ...........................±120mA
Peak Current (COMA_ to USB_)
(pulsed at 1ms, 10% duty cycle).................................±240mA
Continuous Power Dissipation (TA = +70°C)
16-Pin TQFN (derate 20.8mW/°C above +70°C) ........1667mW
Operating Temperature Range ...........................-40°C to +85°C
Storage Temperature Range .............................-65°C to +150°C
Junction Temperature ......................................................+150°C
Lead Temperature (soldering, 10s) .................................+300°C
Note 1: Signals exceeding GND are clamped by internal diodes. Limit forward-diode current to maximum current rating.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V+ = +2.7V to +3.6V, TA = -40°C to +85°C, QP = low, EN = low, unless otherwise noted. Typical values are at V+ = +3.3V and TA =
+25°C.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
V+ = 2.7V, ICOMA_ = TA = +25°C
-10mA, VCOMA_ = 0V,
TA = -40°C to +85°C
1.5V, QP = low
4
5
V+ = 2.7V, ICOMA_ =
-10mA, VCOM_ = 0V,
1.5V, 2.7V, QP = low
4
UNITS
ANALOG SWITCH (COMA_, USB__)
On-Resistance
On-Resistance Match Between
Channels
6
TA = +25°C
TA = -40°C to +85°C
8
RON
ΔRON
V+ = 2.7V, ICOMA_ = TA = +25°C
-10mA, VCOMA_ = 0V,
TA = -40°C to +85°C
1.5V, QP = high
8
V+ = 3.0V, ICOMA_ = TA = +25°C
-10mA, VCOMA_ = 0V,
TA = -40°C to +85°C
1.5V, QP = high
4
V+ = 2.7V, ICOMA_ = TA = +25°C
-10mA, VCOMA_ = 0V,
TA = -40°C to +85°C
1.5V, 2.7V
0.5
IL(OFF)
V+ = 3.6V, VCOMA_ = VUSB__ = 0.3V, 3.3V
-1
On-Leakage Current
IL(ON)
V+ = 3.6V, VCOMA_ = VUSB__ = 0.3V, 3.3V
-1
Fault-Protection Trip Threshold
VFP
V+ = 3.6V, C0 = C1 =
0 or V+
V+ = 3.3V
0.8
Ω
1.0
Off-Leakage Current
I+
12
13
V+ = 2.7V, ICOMA_ = -10mA, VCOMA_ = 0V,
1.5V, 2.7V
Quiescent Supply Current
Ω
17
18
RFLAT (ON)
On-Resistance Flatness
7
0.5
QP = low
250
QP = high
1.1
Ω
+1
µA
+1
µA
600
3
3.6
3.9
4.2
µA
V
ESD PROTECTION
COMA+, COMA-
2
Human Body Model
±15
_______________________________________________________________________________________
kV
USB 2.0 High-Speed, Fault-Tolerant 3:1, 4:1
Multiplexers
(V+ = +2.7V to +3.6V, TA = -40°C to +85°C, QP = low, EN = low, unless otherwise noted. Typical values are at V+ = +3.3V and TA =
+25°C.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
SWITCH AC PERFORMANCE (Note 3)
On-Loss
ONLOSS
f = 10MHz, 0 < VIN < 1V, Figure 1
0.5
dB
Crosstalk
VCT1,
VDCT1
f = 50MHz, Figure 1
-50
dB
Off-Isolation
VISO
f = 50MHz, Figure 1
-45
dB
Charge-Pump Noise
VQP
COMA_, USB_, RL = RS = 50Ω (Note 4)
100
µV
Bandwidth -3dB
BW
RS = RL = unbalanced 50Ω
425
MHz
Off-Capacitance
COFF
f = 1MHz, COMA_, USB_, Figure 2
10.5
pF
On-Capacitance
CON
f = 1MHz, COMA_, USB_, Figure 2
15
pF
Propagation Delay
tPD
RL = RS = 50Ω, Figure 3
200
ps
Output Skew Same Switch
tSK
Skew between opposite transitions in same
switch, Figure 3
100
ps
Fault-Protection Response Time
tFP
VCOMA_ = 0V to 5V to VUSB__ = 2.5V, RL =
50Ω, CL = 10pF, Figure 4
1
µs
Fault-Protection Recovery Time
tFPR
VCOMA_ = 5V to 3V to VUSB__ = 1.5V, RL =
50Ω, CL = 10pF, Figure 4
1
µs
VGEN = 0, CL = 1000pF, Figure 5
25
pC
Charge Injection
Q
Enable Turn-On Time
tON
VUSB0+ = V+, RL = 50Ω, CL = 10pF, Figure 6
2.8
µs
Enable Turn-Off Time
tOFF
VUSB0+ = V+, RL = 50Ω, CL = 10pF, Figure 6
3
ns
Address Transition Time
tTRANS
VUSB0+ = V+, RL = 50Ω, CL = 10pF, Figure 7
1.2
µs
Total Harmonic Distortion Plus
Noise
THD+N
f = 20Hz to 20kHz, VCOMA_ = 1VP-P, RL =
600Ω
0.02
%
SWITCH LOGIC (QP, EN, C0, C1)
Logic-Input Voltage Low
Logic-Input Voltage High
VIL
0.4
VIH
Input Logic Hysteresis
VHYST
Input Leakage Current
ILEAK
1.4
V
100
V+ = 3.6V, C0 = 0 or V+, C1 = 0 or V+
-1
V
mV
1
µA
Note 2: Limits at -40°C are guaranteed by design.
Note 3: Guaranteed by design.
Note 4: Charge-pump noise is specified as a peak-to-peak value.
_______________________________________________________________________________________
3
MAX4899E/MAX4899AE
ELECTRICAL CHARACTERISTICS (continued)
Typical Operating Characteristics
(V+ = 3.3V, QP = EN = low, TA = +25°C, unless otherwise noted.)
V+ = 2.7V
3.4
V+ = 3.3V
RON (Ω)
2.90
2.88
3.0
2.8
TA = +25°C
2.6
2.86
V+ = 3.6V
2.4
2.84
TA = -40°C
2.2
2.82
2.80
1.2
1.8
2.4
3.0
0
1.1
VCOM (V)
2.2
20
15
10
5
0
280
V+ = 3.6V
260
220
V+ = 3.3V
180
160
2.2
0.9
V+ = 2.7V
VIH
0.8
VIL
0.6
0.5
0.4
0.3
0.2
120
0.1
0
-40
-15
10
35
60
85
2.7
3.0
3.3
FREQUENCY RESPONSE
TOTAL HARMONIC DISTORTION
PLUS NOISE vs. FREQUENCY
EYE DIAGRAM
MAX4899E toc07
RL = 600Ω
THD+N (%)
-30
OFF-ISOLATION
-50
-60
CROSSTALK
-70
0.5
0.4
0.3
COMA+ AND COMA- (V)
-20
0.1
0.2
0.1
0
-0.1
-0.2
-80
-0.3
-90
-0.4
-0.5
-100
0.01
10
100
FREQUENCY (MHz)
1000
10
100
1k
FREQUENCY (Hz)
10k
100k
3.6
MAX4899E toc09
SUPPLY VOLTAGE (V)
ON-RESPONSE
85
0.7
TEMPERATURE (°C)
-10
1
60
VCOM (V)
0
-40
35
1.0
140
3.3
10
LOGIC THRESHOLD vs. SUPPLY VOLTAGE
240
200
-15
TEMPERATURE (°C)
100
1.1
COM 0FF-LEAKAGE
-40
3.3
300
QUIESCENT SUPPLY CURRENT (μA)
CL = 1000pF
25
CHARGE INJECTION (pC)
1000
500
0
QUIESCENT SUPPLY CURRENT
vs. TEMPERATURE
MAX4899E toc04
30
0
COM 0N-LEAKAGE
1500
VCOM (V)
CHARGE INJECTION vs. VCOM
4
2500
2000
-500
2.0
3.6
3000
LOGIC THRESHOLD (V)
0.6
3500
MAX4899E toc05
0
4000
MAX4899E toc08
RON (Ω)
TA = +85°C
2.92
4500
LEAKAGE CURRENT (pA)
3.2
2.94
V+ = 3.6V
5000
MAX4899E toc06
2.96
5500
MAX4899E toc02
MAX4899E toc01
2.98
LEAKAGE CURRENT vs. TEMPERATURE
ON-RESISTANCE vs. VCOM
3.6
MAX4899E toc03
ON-RESISTANCE vs. VCOM
3.00
LOSS (dB)
MAX4899E/MAX4899AE
USB 2.0 High-Speed, Fault-Tolerant 3:1, 4:1
Multiplexers
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
TIME (ns)
_______________________________________________________________________________________
USB 2.0 High-Speed, Fault-Tolerant 3:1, 4:1
Multiplexers
PIN
NAME
MAX4899E
1
MAX4899AE
1
2
2
COMA+
3
3
COMA-
GND
FUNCTION
Ground
Analog Switch Common D+ Terminal
Analog Switch Common D- Terminal
4
4
V+
Positive Supply-Voltage Input. Connect V+ to a 2.7V to 3.6V supply voltage. Bypass V+
to GND with a 0.1µF capacitor placed as close as possible to the device.
5
5
C1
Digital Control Input 1. C1 and C0 control the analog signal path as shown in the
Functional Diagrams section.
6
6
C0
Digital Control Input 0. C1 and C0 control the analog signal path as shown in the
Functional Diagrams section.
7, 8
—
N.C.
—
7
USB3-
—
8
USB3+
Analog Switch 3 D+ Terminal
9
9
USB2-
Analog Switch 2 D- Terminal
10
10
USB2+
Analog Switch 2 D+ Terminal
11
11
USB1+
Analog Switch 1 D+ Terminal
12
12
USB1-
Analog Switch 1 D- Terminal
13
13
USB0+
Analog Switch 0 D+ Terminal
14
14
USB0-
Analog Switch 0 D- Terminal
15
15
EN
Active-Low Enable Input. For normal operation, drive EN low. Drive EN high to place all
channels in a high-impedance state. The internal charge pump is turned off when EN is
a logic-high.
16
16
QP
Active-Low Charge-Pump Enable Input. Drive QP low for normal operation. Drive QP
high to disable the charge pump with the switches still active at a reduced analog signal
range and higher RON.
—
—
EP
Exposed Paddle. Connect EP to GND.
No Connection. Not internally connected.
Analog Switch 3 D- Terminal
_______________________________________________________________________________________
5
MAX4899E/MAX4899AE
Pin Description
USB 2.0 High-Speed, Fault-Tolerant 3:1, 4:1
Multiplexers
MAX4899E/MAX4899AE
Test Circuits/Timing Diagrams
V+ 0.1μF
VIN
V+
CHANNEL
SELECT
OFF-ISOLATION = 20log
USB_
C0
C1
NETWORK
ANALYZER
50Ω
50Ω
MAX4899E
MAX4899AE
ON-LOSS = 20log
QP
VOUT
EN
COM_
MEAS.
REF.
CROSSTALK = 20log
GND
50Ω
50Ω
MEASUREMENTS ARE STANDARDIZED AGAINST SHORT AT SOCKET TERMINALS.
OFF-ISOLATION IS MEASURED BETWEEN COM_ AND "OFF" USB_ TERMINAL ON EACH SWITCH.
ON-LOSS IS MEASURED BETWEEN COM_ AND "ON" USB_ TERMINAL ON EACH SWITCH.
CROSSTALK IS MEASURED FROM ONE USB_ CHANNEL TO ANOTHER USB_ CHANNEL.
SIGNAL DIRECTION THROUGH SWITCH IS REVERSED; WORST VALUES ARE RECORDED.
Figure 1. Off-Isolation, On-Loss, and Crosstalk
V+
V+
CHANNEL
SELECT
C0
C1
QP
EN
MAX4899E
MAX4899AE
GND
USB_,
COM_
1MHz
CAPACITANCE
ANALYZER
Figure 2. Channel Off-/On-Capacitance
6
_______________________________________________________________________________________
VOUT
VIN
VOUT
VIN
VOUT
VIN
USB 2.0 High-Speed, Fault-Tolerant 3:1, 4:1
Multiplexers
MAX4899E
MAX4899AE
RS
IN+
USB_+
COMA+
OUT+
RISE-TIME PROPAGATION DELAY = tPLHX OR tPLHY.
FALL-TIME PROPAGATION DELAY = tPHLX OR tPHLY.
tSK = |tPLHX - tPHLX| OR |tPHLY - tPLHY|.
RL
RS
IN-
USB_-
COMA-
OUTRL
C0 C1
tINFALL
tINRISE
V+
90%
VIN+
50%
90%
50%
10%
0V
10%
V+
VIN-
50%
50%
0V
tOUTRISE
tPLHX
tOUTFALL
tPHLX
V+
90%
VOUT+
90%
50%
50%
10%
0V
10%
V+
50%
VOUT-
50%
0V
tPHLY
tPLHY
Figure 3. Propagation Delay and Output Skew
_______________________________________________________________________________________
7
MAX4899E/MAX4899AE
Test Circuits/Timing Diagrams (continued)
MAX4899E/MAX4899AE
USB 2.0 High-Speed, Fault-Tolerant 3:1, 4:1
Multiplexers
Test Circuits/Timing Diagrams (continued)
5V
2.5V
3V
COMA-
0V
tFP
tFPR
tFP
3V
2.5V
1.5V
USB_
0V
Figure 4. Fault-Protection Response/Recovery Time
V+
V+
VCO
V+
C0
VOUT
USB0_
C1
MAX4899E
MAX4899AE
0
CL
1000pF
VOUT
EN
QP
VCO
Δ VOUT
COMA _
GND
VGEN
Δ VOUT IS THE MEASURED VOLTAGE DUE TO CHARGETRANSFER ERROR Q WHEN THE CHANNEL TURNS OFF.
REPEAT TEST FOR EACH SECTION.
Q = Δ VOUT X CL.
Figure 5. Charge Injection
8
_______________________________________________________________________________________
USB 2.0 High-Speed, Fault-Tolerant 3:1, 4:1
Multiplexers
V+
V+ USB0+
USB1+
USB2+
USB3+
C0
C1
V+
0
VOUT
MAX4899E
MAX4899AE
VEN
90%
90%
VOUT
COMA+
EN
50%
VEN
QP GND
50Ω
10pF
0
tON
tOFF
Figure 6. Enable Switching Times
V+
VADD
C0
C1
EN
V+ USB0+
USB1+
USB2+
USB3+
V+
0
VOUT
MAX4899E
MAX4899AE
90%
90%
VOUT
COMA+
QP
50%
VADD
GND
50Ω
10pF
0
tTRANS
tTRANS
Figure 7. Address Transition Time
_______________________________________________________________________________________
9
MAX4899E/MAX4899AE
Test Circuits/Timing Diagrams (continued)
MAX4899E/MAX4899AE
USB 2.0 High-Speed, Fault-Tolerant 3:1, 4:1
Multiplexers
Detailed Description
The MAX4899E/MAX4899AE analog multiplexers combine the low on-capacitance (CON) and low on-resistance (RON) necessary for high-performance switching
applications. These devices are designed for USB 2.0
high-speed applications at 480Mbps. The MAX4899E/
MAX4899AE also handle all the requirements for USB
low- and full-speed signaling. In the case of USB low/
full speed, these devices can function normally even if
the supply voltage is 2.7V, even though the USB signal
may be higher than the supply voltage.
The MAX4899E is a dual 3:1 multiplexer, whereas the
MAX4899AE is a dual 4:1 multiplexer. The MAX4899E/
MAX4899AE feature two digital inputs, C0 and C1, to control the analog signal path. Typical applications include
switching a USB connector between USB and other operations such as serial communications, audio, and video.
An enable input (EN) is provided to disable all channels
and place the device into a high-impedance (off) state,
as well as shutting off the charge pump for minimum
power consumption. The MAX4899E/MAX4899AE feature an additional charge-pump enable input (QP) to
disable the charge pump. The switches remain active
at a lower analog signal range and higher RON.
The MAX4899E/MAX4899AE operate from a 2.7V to
3.6V power-supply voltage and are current-limit protected against +5.5V shorts to COMA- and COMA+.
Digital Control Inputs (C0, C1)
The MAX4899E/MAX4899AE provide two digital control
inputs (C 0 , C 1 ) to select the analog signal path
between the COMA_ and USB__ channels. The truth
tables for the MAX4899E/MAX4899AE are shown in the
Functional Diagrams. Since the MAX4899E only has
three USB__ channels, the code C1:C0 = 1:1 can be
used to place all channels into a high-impedance state.
This is particularly useful for eliminating the extra control line to the EN input that is normally used for disabling all channels. Driving C 0 and C 1 rail-to-rail
minimizes power consumption.
Enable Input (EN)
The MAX4899E/MAX4899AE feature an enable input
(EN) that when driven high places all channels into a
high-impedance state, as an all-off feature. The internal
charge pump is also disabled when EN is high, thus
minimizing the quiescent supply current. For normal
operation, drive EN low.
Charge-Pump Enable Input (QP)
The charge-pump input (QP) disables and enables the
internal charge pump. Drive QP high to disable the
charge pump and reduce the quiescent supply current.
10
With the charge pump disabled, the MAX4899E/
MAX4899AE still function normally; however, the analog
signal range is reduced and the switch on-resistance
(RON) is increased. The analog signal range with the
charge pump disabled is 0V to 1.5V. For normal operation, drive QP low.
Analog Signal Levels
Signals applied to COMA+ are routed to the USB_+ terminals, and signals applied to COMA- are routed to the
USB_- terminals. These multiplexers are bidirectional,
allowing COMA_ and USB_ to be configured as either
inputs or outputs. The D+ and D- notation in the Pin
Description table is arbitrary and can be interchanged.
For example, USB D+ signals can be applied to COMAand are routed to the USB_- terminals. Additionally,
these multiplexers can be used for non-USB signals.
COMA+ and COMA- are normally connected to outside
circuitry and are ±15kV ESD protected.
The MAX4899E is a dual 3:1 multiplexer, allowing
COMA+ to be routed to one of three USB_+ channels,
and COMA- to be routed to one of three USB_- channels.
The MAX4899AE is a dual 4:1 multiplexer, allowing
COMA+ to be routed to one of four USB_+ channels, and
COMA- to be routed to one of four USB_- channels.
Overvoltage Fault Protection
The MAX4899E/MAX4899AE feature +5.5V fault protection to COM A + and COM A -. When a fault occurs
between 4.5V to 5.5V, the switch automatically goes
into a current-limiting mode that limits current to less
than 2mA. Fault protection prevents these switches and
downstream devices from being damaged due to
shorts to the USB bus voltage rail.
Applications Information
USB Switching
The MAX4899E/MAX4899AE analog multiplexers are
fully compliant with the USB 2.0 specification. The low
on-resistance and low on-capacitance of these multiplexers make them ideal for high-performance switching applications. The MAX4899E/MAX4899AE are ideal
for routing USB data lines and for applications that
require switching between different data types (see
Figure 8).
Board Layout
High-speed switches require proper layout and design
procedures for optimum performance. Keep designcontrolled impedance PC board traces as short as possible. Ensure that bypass capacitors are placed as
close to the device as possible and use large ground
planes where possible.
______________________________________________________________________________________
USB 2.0 High-Speed, Fault-Tolerant 3:1, 4:1
Multiplexers
USB0+
VBUS
USB0-
USB1+
AUDIO
HEADPHONE
D+
COMA+
USB1-
MAX4899AE
DCOMA-
USB2+
AUXILIARY
INPUT
USB2-
GND
USB3+
USB
CONNECTOR
USB3-
SERIAL DATA LINK
Figure 8. MAX4899AE Multiplexing Four Data Types
RC 1MΩ
CHARGE-CURRENTLIMIT RESISTOR
As with all Maxim devices, ESD-protection structures are
incorporated on all pins to protect against electrostatic
discharges encountered during handling and assembly.
The COMA+ and COMA- lines have extra protection
against static electricity. Maxim’s engineers have developed state-of-the-art structures to protect these pins
against ESD of ±15kV without damage. The ESD structures withstand high ESD in all states: normal operation,
tri-state output mode, and powered down. After an ESD
event, Maxim’s E-versions keep working without latchup, whereas competing products can latch and must be
powered down to remove latch-up.
Human Body Model
The MAX4899E/MAX4899AE COMA+ and COMA- pins
are characterized for ±15kV ESD protection using the
Human Body Model (MIL-STD-883, Method 3015).
Figure 9a shows the Human Body Model and Figure 9b
shows the current waveform it generates when discharged into a low impedance. This model consists of
a 100pF capacitor charged to the ESD voltage of interest, which is then discharged into the device through a
1.5kΩ resistor.
RD 1500Ω
IP 100%
90%
DISCHARGE
RESISTANCE
Ir
PEAK-TO-PEAK RINGING
(NOT DRAWN TO SCALE)
AMPERES
HIGHVOLTAGE
DC
SOURCE
Cs
100pF
STORAGE
CAPACITOR
DEVICE
UNDER
TEST
36.8%
10%
0
0
Figure 9a. Human Body ESD Test Model
tRL
TIME
tDL
CURRENT WAVEFORM
Figure 9b. Human Body Model Current Waveform
Chip Information
PROCESS: BiCMOS
______________________________________________________________________________________
11
MAX4899E/MAX4899AE
ESD Protection
USB
TRANSCEIVER
USB 2.0 High-Speed, Fault-Tolerant 3:1, 4:1
Multiplexers
MAX4899E/MAX4899AE
Functional Diagrams
V+
V+
MAX4899AE
MAX4899E
USB0+
COMA+
COMA-
COMA+
USB0+
USB0-
USB0-
USB1+
USB1+
USB1-
USB1COMA-
USB2+
USB2+
USB2-
USB2-
QP
USB3+
EN
CONTROL
LOGIC
C0
CHARGE
PUMP
C1
USB3-
EN
CONTROL
LOGIC
C0
GND
CHARGE
PUMP
C1
GND
MAX4899E
QP EN C1 C0
MAX4899AE
QP EN
FUNCTION
COMMENT
NORMAL
OPERATION
0
0
C0
FUNCTION
COMMENT
0
0
COMA+ →USB0+
COMA- →USB0-
NORMAL
OPERATION
C1
0
0
0
0
COMA+ →USB0+
COMA- →USB0-
0
0
0
1
COMA+ →USB1+
COMA- →USB1-
NORMAL
OPERATION
0
0
0
1
COMA+ →USB1+
COMA- →USB1-
NORMAL
OPERATION
0
0
1
0
COMA+ →USB2+
COMA- →USB2-
NORMAL
OPERATION
0
0
1
0
COMA+ →USB2+
COMA- →USB2-
NORMAL
OPERATION
0
0
1
1
HIGH-Z
ALL OFF
0
0
1
1
0
1
X
X
HIGH-Z
ALL OFF
COMA+ →USB3+
COMA- →USB3-
NORMAL
OPERATION
1
1
X
X
HIGH-Z
ALL OFF
0
1
X
X
HIGH-Z
ALL OFF
1
X
X
HIGH-Z
ALL OFF
1
0
0
0
COMA+ →USB0+
COMA- →USB0-
1
LARGER RON
LARGER RON
LARGER RON
1
0
0
1
COMA+ →USB1+
COMA- →USB1-
1
0
1
0
COMA+ →USB2+
COMA- →USB2-
LARGER RON
1
0
1
1
HIGH-Z
ALL OFF
1
0
0
0
COMA+ →USB0+
COMA- →USB0-
1
0
0
1
COMA+ →USB1+
COMA- →USB1-
LARGER RON
1
0
1
0
COMA+ →USB2+
COMA- →USB2-
LARGER RON
1
0
1
1
COMA+ →USB3+
COMA- →USB3-
LARGER RON
X = 1 or 0.
12
______________________________________________________________________________________
QP
USB 2.0 High-Speed, Fault-Tolerant 3:1, 4:1
Multiplexers
USB0- 14
MAX4899E
EN 15
1
2
3
4
COMA+
COMA-
V+
+
GND
QP 16
8
N.C.
USB0+ 13
7
N.C.
USB0- 14
6
C0
EN 15
5
C1
QP 16
USB2+
USB2-
11
10
9
*EP
MAX4899AE
+
1
2
3
4
V+
*EP
12
COMA-
9
USB1+
USB2-
10
COMA+
USB2+
11
USB1-
USB1+
12
TOP VIEW
GND
USB0+ 13
USB1-
TOP VIEW
8
USB3+
7
USB3-
6
C0
5
C1
TQFN
TQFN
*CONNECT EXPOSED PAD TO GND
______________________________________________________________________________________
13
MAX4899E/MAX4899AE
Pin Configurations
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
(NE - 1) X e
E
MARKING
12x16L QFN THIN.EPS
MAX4899E/MAX4899AE
USB 2.0 High-Speed, Fault-Tolerant 3:1, 4:1
Multiplexers
E/2
D2/2
(ND - 1) X e
AAAA
D/2
e
CL
D
D2
k
CL
b
0.10 M C A B
E2/2
L
E2
0.10 C
C
L
C
L
0.08 C
A
A2
A1
L
L
e
e
PACKAGE OUTLINE
8, 12, 16L THIN QFN, 3x3x0.8mm
21-0136
PKG
8L 3x3
REF.
12L 3x3
16L 3x3
MIN. NOM. MAX.
MIN. NOM. MAX.
0.70
0.75
0.80
0.70
0.75
0.80
0.70
0.75
0.80
b
0.25
0.30
0.35
0.20
0.25
0.30
0.20
0.25
0.30
D
2.90
3.00
3.10
2.90
3.00
3.10
2.90
3.00
3.10
E
2.90
3.00
3.10
2.90
3.00
3.10
2.90
3.00
3.10
L
0.65 BSC.
0.35
0.55
0.50 BSC.
0.75
0.45
0.55
0.50 BSC.
0.65
0.30
0.40
8
12
16
ND
2
3
4
NE
2
3
4
N
0
A1
A2
k
0.02
0.05
0
0.20 REF
0.25
-
0.02
0.05
0
0.20 REF
-
0.25
-
0.02
0.50
0.05
0.20 REF
-
0.25
-
1
2
EXPOSED PAD VARIATIONS
MIN. NOM. MAX.
A
e
I
PKG.
CODES
TQ833-1
T1233-1
D2
E2
MIN.
NOM.
MAX.
MIN.
NOM.
MAX.
0.25
0.70
1.25
0.25
0.70
1.25
1.10
1.25
1.25
PIN ID
JEDEC
0.35 x 45°
WEEC
0.35 x 45°
WEED-1
0.95
1.10
T1233-3
0.95
1.10
1.25
0.95
1.10
1.25
0.35 x 45°
WEED-1
T1233-4
0.95
1.10
1.25
0.95
1.10
1.25
0.35 x 45°
WEED-1
T1633-2
0.95
1.10
1.25
0.95
1.10
1.25
0.35 x 45°
WEED-2
0.95
T1633F-3
0.65
0.80
0.95
0.65
0.80
0.95
0.225 x 45°
WEED-2
T1633FH-3
0.65
0.80
0.95
0.65
0.80
0.95
0.225 x 45°
WEED-2
T1633-4
0.95
1.10
1.25
0.95
1.10
1.25
0.35 x 45°
WEED-2
T1633-5
0.95
1.10
1.25
0.95
1.10
1.25
0.35 x 45°
WEED-2
-
NOTES:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
DIMENSIONING & TOLERANCING CONFORM TO ASME Y14.5M-1994.
ALL DIMENSIONS ARE IN MILLIMETERS. ANGLES ARE IN DEGREES.
N IS THE TOTAL NUMBER OF TERMINALS.
THE TERMINAL #1 IDENTIFIER AND TERMINAL NUMBERING CONVENTION SHALL CONFORM TO
JESD 95-1 SPP-012. DETAILS OF TERMINAL #1 IDENTIFIER ARE OPTIONAL, BUT MUST BE LOCATED
WITHIN THE ZONE INDICATED. THE TERMINAL #1 IDENTIFIER MAY BE EITHER A MOLD OR
MARKED FEATURE.
DIMENSION b APPLIES TO METALLIZED TERMINAL AND IS MEASURED BETWEEN 0.20 mm AND 0.25 mm
FROM TERMINAL TIP.
ND AND NE REFER TO THE NUMBER OF TERMINALS ON EACH D AND E SIDE RESPECTIVELY.
DEPOPULATION IS POSSIBLE IN A SYMMETRICAL FASHION.
COPLANARITY APPLIES TO THE EXPOSED HEAT SINK SLUG AS WELL AS THE TERMINALS
.
DRAWING CONFORMS TO JEDEC MO220 REVISION C.
MARKING IS FOR PACKAGE ORIENTATION REFERENCE ONLY.
NUMBER OF LEADS SHOWN ARE FOR REFERENCE ONLY.
WARPAGE NOT TO EXCEED 0.10mm.
PACKAGE OUTLINE
8, 12, 16L THIN QFN, 3x3x0.8mm
21-0136
I
2
2
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
14 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2006 Maxim Integrated Products
Boblet
is a registered trademark of Maxim Integrated Products, Inc.