MAXIM MAX5159CEE

19-1315; Rev 1; 12/97
Low-Power, Dual, 10-Bit, Voltage-Output DACs
with Serial Interface
The MAX5158/MAX5159 low-power, serial, voltageoutput, dual, 10-bit digital-to-analog converters (DACs)
consume only 500µA from a single +5V (MAX5158) or
+3V (MAX5159) supply. These devices feature Rail-toRail® output swing and are available in a space-saving
16-pin QSOP package. To maximize dynamic range, the
DAC output amplifiers are configured with an internal gain
of +2V/V.
The 3-wire serial interface is SPI™/QSPI™ and
Microwire™ compatible. Each DAC has a doublebuffered input organized as an input register followed by
a DAC register, which allows the input and DAC registers
to be updated independently or simultaneously with a
16-bit serial word. Additional features include a 2µA programmable shutdown, hardware-shutdown lockout, a
separate reference-voltage input for each DAC that
accepts AC and DC signals, and an active-low clear input
(CL) that resets all registers and DACs to zero. The
MAX5158/MAX5159 provide a programmable logic pin
for added functionality and a serial-data output pin for
daisy chaining.
____________________________Features
♦ 10-Bit Dual DAC with Internal Gain of +2V/V
♦ Rail-to-Rail Output Swing
♦ 8µs Settling Time
♦ Single-Supply Operation: +5V (MAX5158)
+3V (MAX5159)
♦ Low Quiescent Current: 500µA (normal operation)
2µA (shutdown mode)
♦ SPI/QSPI and Microwire Compatible
♦ Available in Space-Saving 16-Pin QSOP Package
♦ Power-On Reset Clears Registers and DACs to Zero
♦ Adjustable Output Offset
______________Ordering Information
PART
MAX5158CPE
MAX5158CEE
MAX5158EPE
MAX5158EEE
MAX5158MJE
________________________Applications
Digital Offset and Gain Adjustment
µP-Controlled Systems
TEMP. RANGE
0°C to +70°C
0°C to +70°C
-40°C to +85°C
-40°C to +85°C
-55°C to +125°C
PIN-PACKAGE
16 Plastic DIP
16 QSOP
16 Plastic DIP
16 QSOP
16 CERDIP*
Ordering Information continued at end of data sheet.
*Contact factory for availability.
Motion Control
Remote Industrial Controls
_________________________________________________________Functional Diagram
DOUT
CL
PDL
DGND
AGND
VDD
REFA
OSA
DECODE
CONTROL
R
R
INPUT
REG A
16-BIT
SHIFT
REGISTER
DIN
OUTA
OSB
DAC A
R
MAX5158
MAX5159
SR
CONTROL
CS
DAC
REG A
LOGIC
OUTPUT
SCLK
UPO
INPUT
REG B
DAC
REG B
R
OUTB
DAC B
REFB
Rail-to-Rail is a registered trademark of Nippon Motorola Ltd. Microwire is a trademark of National Semiconductor Corp.
SPI and QSPI are trademarks of Motorola, Inc.
________________________________________________________________ Maxim Integrated Products
1
For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800
For small orders, phone 408-737-7600 ext. 3468.
MAX5158/MAX5159
_______________General Description
MAX5158/MAX5159
Low-Power, Dual, 10-Bit Voltage-Output DACs
with Serial Interface
ABSOLUTE MAXIMUM RATINGS
VDD to AGND............................................................-0.3V to +6V
VDD to DGND ...........................................................-0.3V to +6V
AGND to DGND ..................................................................±0.3V
OSA, OSB to AGND........................(AGND - 4V) to (VDD + 0.3V)
REF_, OUT_ to AGND.................................-0.3V to (VDD + 0.3V)
Digital Inputs (SCLK, DIN, CS, CL, PDL)
to DGND............................................................(-0.3V to +6V)
Digital Outputs (DOUT, UPO)
to DGND ................................................-0.3V to (VDD + 0.3V)
Maximum Current into Any Pin .........................................±20mA
Continuous Power Dissipation (TA = +70°C)
Plastic DIP (derate 10.5mW/°C above +70°C) ...........842mW
QSOP (derate 8.30mW/°C above +70°C) ...................667mW
CERDIP (derate 10.00mW/°C above +70°C) ..............800mW
Operating Temperature Ranges
MAX515_ _C_ E .................................................0°C to +70°C
MAX515_ _E_ E ..............................................-40C° to +85°C
MAX515_ _MJE.............................................-55°C to +125°C
Storage Temperature Range .............................-65°C to +160°C
Lead Temperature (soldering, 10sec) .............................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS—MAX5158
(VDD = +5V ±10%, VREFA = VREFB = 2.048V, RL = 10kΩ, CL = 100pF, TA = TMIN to TMAX, unless otherwise noted. Typical values are
at TA= +25°C (OS_ tied to AGND for a gain of +2V/V).)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
STATIC PERFORMANCE
Resolution
10
Bits
Integral Nonlinearity
INL
(Note 1)
±1
LSB
Differential Nonlinearity
DNL
Guaranteed monotonic
±1
LSB
VOS_
Code = 2
Offset Error
Offset Tempco
TCVOS
±6
Normalized to 2.048V
4
Gain Error
-0.1
Gain-Error Tempco
VDD Power-Supply
Rejection Ratio
PSRR
Normalized to 2.048V
4
2.7V ≤ VDD ≤ 5.5V
20
mV
ppm/°C
1
LSB
ppm/°C
260
µV/V
REFERENCE INPUT
Reference Input Range
REF
Reference Input Resistance
RREF
0
Minimum with code 1558 hex
18
VDD - 1.4
V
25
kΩ
MULTIPLYING-MODE PERFORMANCE
Reference 3dB Bandwidth
Input code = 1FF8 hex,
VREF_ = 0.67Vp-p at 0.75VDC
300
kHz
Reference Feedthrough
Input code = 0000 hex,
VREF_ = (VDD - 1.4 Vp-p) at 1kHz
-82
dB
Input code = 1FF8 hex,
VREF_ = 1Vp-p at 1.25VDC, f = 25kHz
75
dB
Signal-to-Noise plus
Distortion Ratio
SINAD
DIGITAL INPUTS
Input High Voltage
VIH
CL, PDL, CS, DIN, SCLK
Input Low Voltage
VIL
CL, PDL, CS, DIN, SCLK
Input Hysteresis
VHYS
Input Leakage Current
IIN
Input Capacitance
CIN
2
3
V
0.8
200
VIN = 0V to VDD
0.001
8
_______________________________________________________________________________________
V
mV
±1
µA
pF
Low-Power, Dual, 10-Bit, Voltage-Output DACs
with Serial Interface
(VDD = +5V ±10%, VREFA = VREFB = 2.048V, RL = 10kΩ, CL = 100pF, TA = TMIN to TMAX, unless otherwise noted. Typical values are
at TA= +25°C (OS_ tied to AGND for a gain of +2V/V).)
PARAMETER
SYMBOL
CONDITIONS
DIGITAL OUTPUTS (DOUT, UPO)
Output High Voltage
VOH
ISOURCE = 2mA
Output Low Voltage
VOL
ISINK = 2mA
DYNAMIC PERFORMANCE
Voltage Output Slew Rate
SR
Output Settling Time
To 1/2LSB of full-scale, VSTEP = 4V
Output Voltage Swing
Rail-to-rail (Note 2)
OSA or OSB Input Resistance
ROS_
MIN
24
CS = VDD, fDIN = 100kHz, VSCLK = 5Vp-p
Digital Crosstalk
POWER SUPPLIES
Positive Supply Voltage
VDD
Power-Supply Current
IDD
Power-Supply Current
in Shutdown
Reference Current in Shutdown
tCP
SCLK Pulse Width High
SCLK Pulse Width Low
0.13
0.4
(Note 4)
UNITS
V
V
0.75
V/µs
8
µs
0 to VDD
V
34
kΩ
25
µs
5
nV-s
5
nV-s
4.5
(Note 3)
IDD(SHDN) (Note 3)
TIMING CHARACTERISTICS
SCLK Clock Period
MAX
VDD - 0.5
Time Required to Exit Shutdown
Digital Feedthrough
TYP
5.5
V
0.5
0.65
mA
2
10
µA
0
±1
µA
100
ns
tCH
40
ns
tCL
40
ns
CS Fall to SCLK Rise Setup Time
tCSS
40
ns
SCLK Rise to CS Rise Hold Time
tCSH
0
ns
SDI Setup Time
tDS
40
ns
SDI Hold Time
tDH
0
ns
SCLK Rise to DOUT
Valid Propagation Delay
tDO1
CLOAD = 200pF
80
ns
SCLK Fall to DOUT
Valid Propagation Delay
tDO2
CLOAD = 200pF
80
ns
SCLK Rise to CS Fall Delay
tCS0
10
ns
CS Rise to SCLK Rise Hold
tCS1
40
ns
CS Pulse Width High
tCSW
100
ns
Note 1: Accuracy is specified from code 2 to code 1023.
Note 2: Accuracy is better than 1LSB for VOUT_ greater than 6mV and less than VDD - 50mV. Guaranteed by PSRR test at the
end points.
Note 3: Digital inputs are set to either VDD or DGND, code = 0000 hex, RL = ∞.
Note 4: SCLK minimum clock period includes rise and fall times.
_______________________________________________________________________________________
3
MAX5158/MAX5159
ELECTRICAL CHARACTERISTICS—MAX5158 (continued)
MAX5158/MAX5159
Low-Power, Dual, 10-Bit Voltage-Output DACs
with Serial Interface
ELECTRICAL CHARACTERISTICS—MAX5159
(VDD = +2.7V to +3.6V, VREFA = VREFB = 1.25V, RL = 10kΩ, CL = 100pF, TA = TMIN to TMAX, unless otherwise noted. Typical values
are at TA = +25°C (OS_ pins tied to AGND for a gain of +2V/V).)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
STATIC PERFORMANCE
Resolution
10
Bits
Integral Nonlinearity
INL
(Note 5)
±1
LSB
Differential Nonlinearity
DNL
Guaranteed monotonic
±1
LSB
Offset Error
VOS
Code = 3
±6
Offset Tempco
TCVOS
Normalized to 1.25V
6.5
Gain Error
-0.1
Gain-Error Tempco
VDD Power-Supply
Rejection Ratio
PSRR
Normalized to 1.25V
6.5
2.7V ≤ VDD ≤ 3.6V
40
mV
ppm/°C
±1
LSB
ppm/°C
320
µV/V
REFERENCE INPUT (VREF)
Reference Input Range
REF
Reference Input Resistance
RREF
0
Minimum with code 1558 hex
18
VDD - 1.4
V
25
kΩ
MULTIPLYING-MODE PERFORMANCE
Reference 3dB Bandwidth
Input code = 1FF8 hex,
VREF_ = 0.67Vp-p at 0.75VDC
300
kHz
Reference Feedthrough
Input code = 0000 hex,
VREF_ = (VDD - 1.4)Vp-p at 1kHz
-82
dB
Input code = 1FF8 hex,
VREF_ = 1Vp-p at 1VDC, f = 15kHz
73
dB
Signal-to-Noise plus
Distortion Ratio
SINAD
DIGITAL INPUTS
Input High Voltage
VIH
CL, PDL, CS, DIN, SCLK
Input Low Voltage
VIL
CL, PDL, CS, DIN, SCLK
Input Hysteresis
2.2
VHYS
Input Leakage Current
IIN
Input Capacitance
CIN
V
0.8
200
VIN = 0V to VDD
0
V
mV
±1
8
µA
pF
DIGITAL OUTPUTS
Output High Voltage
VOH
ISOURCE = 2mA
Output Low Voltage
VOL
ISINK = 2mA
VDD - 0.5
V
0.13
0.4
V
DYNAMIC PERFORMANCE (DOUT, UPO)
Voltage Output Slew Rate
SR
Output Settling Time
To 1/2LSB of full-scale, VSTEP = 2.5V
Output Voltage Swing
Rail-to-rail (Note 6)
OSA or OSB Input Resistance
ROS_
24
Time Required for Valid
Operation after Shutdown
Digital Feedthrough
Digital Crosstalk
4
CS = VDD, fDIN = 100kHz, VSCLK = 3Vp-p
0.75
V/µs
8
µs
0 to VDD
V
34
kΩ
25
µs
5
5
nV-s
nV-s
_______________________________________________________________________________________
Low-Power, Dual, 10-Bit, Voltage-Output DACs
with Serial Interface
(VDD = +2.7V to +3.6V, VREFA = VREFB = 1.25V, RL = 10kΩ, CL = 100pF, TA = TMIN to TMAX, unless otherwise noted. Typical values
are at TA = +25°C (OS_ pins tied to AGND for a gain of +2V/V).)
PARAMETER
SYMBOL
POWER SUPPLIES
Positive Supply Voltage
VDD
Power-Supply Current
IDD
Power-Supply Current
in Shutdown
CONDITIONS
MIN
TYP
MAX
3.6
V
0.5
0.6
mA
1
8
µA
±1
µA
2.7
(Note 7)
IDD(SHDN) (Note 7)
Reference Current in
Shutdown
UNITS
TIMING CHARACTERISTICS
SCLK Clock Period
tCP
100
ns
SCLK Pulse Width High
tCH
40
ns
SCLK Pulse Width Low
tCL
40
ns
CS Fall to SCLK Rise
Setup Time
tCSS
40
ns
SCLK Rise to CS Rise
Hold Time
tCSH
0
ns
SDI Setup Time
tDS
50
ns
SDI Hold Time
tDH
0
ns
SCLK Rise to DOUT Valid
Propagation Delay
tDO1
CLOAD = 200pF
120
ns
SCLK Fall to DOUT Valid
Propagation Delay
tDO2
CLOAD = 200pF
120
ns
SCLK Rise to CS Fall Delay
tCS0
10
ns
CS Rise to SCLK Rise Hold
tCS1
40
ns
CS Pulse Width High
tCSW
100
ns
(Note 4)
Note 5: Accuracy is specified from code 3 to code 1023.
Note 6: Accuracy is better than 1LSB for VOUT greater than 6mV and less than VDD - 80mV. Guaranteed by PSRR test at the end
points.
Note 7: Digital inputs are set to either VDD or DGND, code = 0000 hex, RL = ∞.
_______________________________________________________________________________________
5
MAX5158/MAX5159
ELECTRICAL CHARACTERISTICS—MAX5159 (continued)
__________________________________________Typical Operating Characteristics
(VDD = +5V, RL = 10kΩ, CL = 100pF, OS_ pins tied to AGND, TA = +25°C, unless otherwise noted.)
MAX5158
-10
-12
-14
-16
550
CODE = 0000 (HEX)
1110
1480
1850
-55 -35 -15
FREQUENCY (kHz)
25
45
65
-80
85 105 125
1
10
0.25
0
-0.25
-0.5
-50
VREF = 3.6Vp-p @ 1.88VDC
CODE = 0000 (HEX)
-60
SHUTDOWN CURRENT
vs. TEMPERATURE
-70
-80
-90
-100
-110
-120
6
VREF = 1V
5
-130
-0.75
100
FREQUENCY (kHz)
REFERENCE FEEDTHROUGH AT 1kHz
RELATIVE OUTPUT (dB)
MAX5158/5159 toc04
0.50
MAX5158/5159 toc03
-60
TEMPERATURE (°C)
FULL-SCALE ERROR vs. RESISTIVE LOAD
FULL-SCALE ERROR (LSB)
5
SHUTDOWN CURRENT (µA)
740
MAX5158/5159 toc05
370
-50
-70
VREF = 2.048V
RL = ∞
400
-20
1
-40
450
VREF = 0.67Vp-p @ 2.5VDC
CODE = 1FF8 (HEX)
-18
600
500
VREF = 1Vp-p @ 2.5VDC
CODE = 1FF8 (HEX)
THD + NOISE (dB)
-8
-30
MAX5158/5159 toc02
-6
CODE = 1FF8 (HEX)
650
SUPPLY CURRENT (µA)
-4
RELATIVE OUTPUT (dB)
700
MAX5158/5159-01
0
-2
TOTAL HARMONIC DISTORTION
PLUS NOISE vs. FREQUENCY
SUPPLY CURRENT vs. TEMPERATURE
MAX5158/5159 toc06
REFERENCE VOLTAGE INPUT
FREQUENCY RESPONSE
4
3
2
1
-140
-1.0
0
-150
0.1
1
10
100
-55 -35 -15
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
5
25
45 65
FREQUENCY (kHz)
OUTPUT FFT PLOT
DYNAMIC RESPONSE RISE TIME
DYNAMIC RESPONSE FALL TIME
MAX5158/5159 toc09
MAX5158/5159 toc08
MAX5158/5159 toc07
VREF = 2.45Vp-p @ 1.225VDC
f = 1kHz
CODE = 1FF8 (HEX)
-10
-20
-30
CS
5V/div
CS
5V/div
OUT_
1V/div
OUT_
1V/div
NOTE: RELATIVE TO FULL-SCALE
-40
-50
-60
-70
-80
-90
-100
0.5
1.6
2.7
3.8
FREQUENCY (kHz)
6
85 105 125
TEMPERATURE (°C)
RL (kΩ)
0
RELATIVE OUTPUT (dB)
MAX5158/MAX5159
Low-Power, Dual, 10-Bit Voltage-Output DACs
with Serial Interface
4.9
2µs/div
2µs/div
6.0
VREF = 2.048V
VREF = 2.048V
_______________________________________________________________________________________
Low-Power, Dual, 10-Bit, Voltage-Output DACs
with Serial Interface
MAX5159
-10
-12
-14
VREF = 0.67Vp-p @ 0.75VDC
CODE = 1FF8
480
460
320
640
-60
CODE = 0000 (HEX)
-70
400
1
-50
420
-20
960
1280
1600
-80
-55 -35 -15
5
25
45
65
1
85 105 125
10
100
TEMPERATURE (°C)
FREQUENCY (kHz)
FULL-SCALE ERROR vs. RESISTIVE LOAD
REFERENCE FEEDTHROUGH AT 1kHz
SHUTDOWN CURRENT
vs. TEMPERATURE
-0.25
-0.50
-0.75
-70
-80
-90
-100
-110
-120
3.0
2.8
SHUTDOWN CURRENT (µA)
0
VREF = 1.6Vp-p @ 0.88VDC
CODE = 0000 (HEX)
-60
RELATIVE OUTPUT (dB)
MAX5158/5159 toc13
0.25
-50
0.1
1
10
100
2.4
2.2
2.0
1.8
1.6
1.4
-140
1.2
1.0
-55 -35 -15
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
FREQUENCY (kHz)
OUTPUT FFT PLOT
DYNAMIC RESPONSE RISE TIME
-20
MAX5158/5159toc16
VREF = 1.4Vp-p @ 0.75VDC
f = 1kHz
CODE = 1FF8 (HEX)
25
45
65
85 105 125
DYNAMIC RESPONSE FALL TIME
MAX5158/5159 toc17
-10
5
TEMPERATURE (°C)
RL (kΩ)
0
VREF = 1V
RL = ∞
2.6
-130
-150
-1.00
MAX5158/5159 toc15
FREQUENCY (kHz)
0.50
FULL-SCALE ERROR (LSB)
-40
500
440
-16
RELATIVE OUTPUT (dB)
520
VREF = 1Vp-p @ 1VDC
CODE = 1FF8 (HEX)
THD + NOISE (dB)
-8
CODE = 1FF8 (HEX)
-30
MAX5158/5159 toc11
-6
540
VREF = 1V
RL = ∞
MAX5158/5159 toc14
RELATIVE OUTPUT (dB)
-4
560
SUPPLY CURRENT (µA)
MAX5158/5159 toc10
0
-2
-18
TOTAL HARMONIC DISTORTION
PLUS NOISE vs. FREQUENCY
SUPPLY CURRENT vs. TEMPERATURE
MAX5158/5159 toc12
REFERENCE VOLTAGE INPUT
FREQUENCY RESPONSE
MAX5158/MAX5159
____________________________Typical Operating Characteristics (continued)
(VDD = +3V, RL = 10kΩ, CL = 100pF, OS_ pins tied to AGND, TA = +25°C, unless otherwise noted.)
MAX5158/5159 toc18
CS
2V/div
CS
2V/div
OUT_
500mV/div
OUT_
500mV/div
-30
-40
-50
-60
-70
-80
-90
-100
0.5
1.6
2.7
3.8
FREQUENCY (kHz)
4.9
2µs/div
6.0
VREF = 1.25V
2µs/div
VREF = 1.25V
_______________________________________________________________________________________
7
_____________________________Typical Operating Characteristics (continued)
(VDD = +5V (MAX5158), VDD = +3V (MAX5159), RL = 10kΩ, CL = 100pF, OS_ pins tied to AGND, unless otherwise noted.)
MAX5158/MAX5159
0.55
0.60
CODE = 1FF8 (HEX)
SUPPLY CURRENT (mA)
CODE = 1FF8 (HEX)
MAX5158/5159 TOC19
0.60
MAX5159
SUPPLY CURRENT vs. SUPPLY VOLTAGE
0.50
CODE = 0000 (HEX)
0.45
0.55
MAX5158/5159 TOC19a
MAX5158
SUPPLY CURRENT vs. SUPPLY VOLTAGE
SUPPLY CURRENT (mA)
0.50
CODE = 0000 (HEX)
0.45
0.40
0.40
4.50
4.75
5.00
5.25
5.50
2.7
MAX5158
MAJOR-CARRY TRANSITION
3.0
3.3
3.6
SUPPLY VOLTAGE (V)
MAX5158/5159 toc20
SUPPLY VOLTAGE (V)
CS
2V/div
OUT_
50mV/div
AC COUPLED
5µs/div
TRANSITION FROM 1000 (HEX) TO 0FF8 (HEX)
MAX5158
ANALOG CROSSTALK
MAX5158/5159 toc22
MAX5158
DIGITAL FEEDTHROUGH
MAX5158/5159 toc21
MAX5158/MAX5159
Low-Power, Dual, 10-Bit Voltage-Output DACs
with Serial Interface
OUTA
5V/div
OUTA
500µV/div
AC COUPLED
OUTB
200µV/div
AC COUPLED
250µs/div
2.5µs/div
VREF = 2.048V, GAIN = +2V/V, CODE = 1FF8 HEX
8
SCLK
5V/div
_______________________________________________________________________________________
Low-Power, Dual, 10-Bit, Voltage-Output DACs
with Serial Interface
MAX5158/MAX5159
_____________________Pin Description
OS_
R
PIN
NAME
FUNCTION
1
AGND
Analog Ground
2
OUTA
DAC A Output Voltage
3
OSA
DAC A Offset Adjustment
4
REFA
Reference for DAC A
5
CL
Active-Low Clear Input. Resets all registers to zero. DAC outputs go to 0V.
6
CS
Chip-Select Input
7
DIN
Serial-Data Input
8
SCLK
Serial Clock Input
9
DGND
Digital Ground
Figure 1. Simplified DAC Circuit Diagram
10
DOUT
Serial-Data Output
11
UPO
User-Programmable Output
12
PDL
Power-Down Lockout. The device cannot be powered down when PDL is low.
13
REFB
Reference for DAC B
14
OSB
DAC B Offset Adjustment
15
OUTB
DAC B Output Voltage
VOUT = (VREF x NB / 1024) x 2
where NB is the numeric value of the DAC’s binary input
code (0 to 1023) and VREF is the reference voltage.
The reference input impedance ranges from 18kΩ
(1558 hex) to several giga ohms (with an input code of
0000 hex). The reference input capacitance is code
dependent and typically ranges from 15pF with an
input code of all zeros to 50pF with a full-scale input
code.
16
VDD
Positive Power Supply
R
R
2R
2R
D0
_______________Detailed Description
The MAX5158/MAX5159 dual, 10-bit, voltage-output
DACs are easily configured with a 3-wire serial interface. These devices include a 16-bit data-in/data-out
shift register, and each DAC has a double-buffered
input composed of an input register and a DAC register
(see Functional Diagram). In addition, trimmed internal
resistors produce an internal gain of +2V/V that maximizes output voltage swing. The amplifier’s offset-adjust
pin allows for a DC shift in the DAC’s output.
Both DACs use an inverted R-2R ladder network that
produces a weighted voltage proportional to the input
voltage value. Each DAC has its own reference input to
facilitate independent full-scale values. Figure 1
depicts a simplified circuit diagram of one of the two
DACs.
Reference Inputs
The reference inputs accept both AC and DC values
with a voltage range extending from 0V to (VDD - 1.4V).
Determine the output voltage using the following equation (OS_ = AGND):
R
2R
D7
OUT_
R
2R
2R
D8
D9
REF_
AGND
SHOWN FOR ALL 1s ON DAC
Output Amplifier
The output amplifiers on the MAX5158/MAX5159 have
internal resistors that provide for a gain of +2V/V when
OS_ is connected to AGND. These resistors are
trimmed to minimize gain error. The output amplifiers
have a typical slew rate of 0.75V/µs and settle to
1/2LSB within 8µs, with a load of 10kΩ in parallel with
100pF. Loads less than 2kΩ degrade performance.
The OS_ pin can be used to produce an adjustable offset voltage at the output. For instance, to achieve a 1V
offset, apply -1V to the OS_ pin to produce an output
range from 1V to (1V + VREF x 2). Note that the DAC’s
output range is still limited by the maximum output voltage specification.
Power-Down Mode
The MAX5158/MAX5159 feature a software-programmable shutdown mode that reduces the typical supply
current to 2µA. The two DACs can be shutdown independently, or simultaneously using the appropriate programming command. Enter shutdown mode by writing
the appropriate input-control word (Table 1). In shutdown mode, the reference inputs and amplifier outputs become high impedance, and the serial interface
_______________________________________________________________________________________
9
MAX5158/MAX5159
Low-Power, Dual, 10-Bit Voltage-Output DACs
with Serial Interface
MAX5158
MAX5159
SCLK
SK
DIN
SO
remains active. Data in the input registers is saved,
allowing the MAX5158/MAX5159 to recall the output
state prior to entering shutdown when returning to normal mode. Exit shutdown by recalling the previous condition or by updating the DAC with new information.
When returning to normal operation (exiting shutdown),
wait 20µs for output stabilization.
MICROWIRE
PORT
Serial Interface
CS
The MAX5158/MAX5159 3-wire serial interface is compatible with both Microwire (Figure 2) and SPI/QSPI
(Figure 3) serial-interface standards. The 16-bit serial
input word consists of an address bit, two control bits, 10
bits of data (MSB to LSB), and 3 sub-bits as shown in
Figure 4. The address and control bits determine the
MAX5158/MAX5159’s response, as outlined in Table 1.
I/O
Figure 2. Connections for Microwire
Table 1. Serial-Interface Programming Command
16-BIT SERIAL WORD
FUNCTION
D9..........................D0
S2–S0
(MSB)
(LSB)
A0
C1
C0
0
0
1
10-bit DAC data
000
Load input register A; DAC registers are unchanged.
1
0
1
10-bit DAC data
000
Load input register B; DAC registers are unchanged.
0
1
0
10-bit DAC data
000
Load input register A; all DAC registers are updated.
1
1
0
10-bit DAC data
000
Load input register B; all DAC registers are updated.
0
1
1
10-bit DAC data
000
Load all DAC registers from the shift register
(start up both DACs with new data.).
1
0
0
xxxxxxxxxx
000
Update both DAC registers from their respective input registers
(start up both DACs with data previously stored in the input registers).
1
1
1
xxxxxxxxxx
000
Shut down both DACs (provided PDL = 1).
0
0
0
0 0 1 x xxxxxx
000
Update DAC register A from input register A
(start up DAC A with data previously stored in input register A).
0
0
0
1 0 1 x xxxxxx
000
Update DAC register B from input register B
(start up DAC B with data previously stored in input register B).
0
0
0
1 1 0 x xxxxxx
000
Shut down DAC A (provided PDL = 1).
0
0
0
1 1 1 x xxxxxx
000
Shut down DAC B (provided PDL = 1).
0
0
0
0 1 0 x xxxxxx
000
UPO goes low (default).
0
0
0
0 1 1 x xxxxxx
000
UPO goes high.
0
0
0
1 0 0 1 xxxxxx
000
Mode 1, DOUT clocked out on SCLK’s rising edge.
0
0
0
1 0 0 0 xxxxxx
000
Mode 0, DOUT clocked out on SCLK’s falling edge (default).
0
0
0
0 0 0 x xxxxxx
000
No operation (NOP).
x = Don’t care
Note: When A0, C1, and C0 = 0, then D9, D8, D7, and D6 become control bits. S2–S0 are sub bits, always zero.
10
______________________________________________________________________________________
Low-Power, Dual, 10-Bit, Voltage-Output DACs
with Serial Interface
SS
DIN
MAX5158
MAX5159
MOSI
SCLK
SPI/QSPI
PORT
SCK
CS
I/O
CPOL = 0, CPHA = 0
Figure 3. Connections for SPI/QSPI
The general timing diagram of Figure 5 illustrates how
data is acquired. Driving CS low enables the device to
receive data. Otherwise, the interface control circuitry is
disabled. With CS low, data at DIN is clocked into the
register on the rising edge of SCLK. As CS goes high,
data is latched into the input and/or DAC registers,
depending on the address and control bits. The maximum clock frequency guaranteed for proper operation
is 10MHz. Figure 6 depicts a more detailed timing diagram of the serial interface.
MSB ..................................................................................LSB
16 Bits of Serial Data
Address Bits
A0
Control Bits MSB....DataBits...LSB Sub Bits
C1, C0
D9.................. ......D0 S2–S0
1 Address/
2 Control Bits
000
10 Data Bits
Figure 4. Serial-Data Format
CS
COMMAND
EXECUTED
SCLK
1
DIN
A0
8
C1
C0
D9
D8
D7
D6
D5
9
D4
16
D3
D2
D1
D0
S2
S1
S0
Figure 5. Serial-Interface Timing Diagram
______________________________________________________________________________________
11
MAX5158/MAX5159
The MAX5158/MAX5159’s digital inputs are double
buffered, which allows any of the following: loading the
input register(s) without updating the DAC register(s),
updating the DAC register(s) from the input register(s),
or updating the input and DAC registers concurrently.
The address and control bits allow the DACs to act
independently.
Send the 16-bit data as one 16-bit word (QSPI) or two
8-bit packets (SPI, Microwire), with CS low during this
period. The address and control bits determine which
register will be updated and the state of the registers
when exiting shutdown. The 3-bit address/control determines the following:
• registers to be updated
• clock edge on which data is to be clocked out via
the serial-data output (DOUT)
• state of the user-programmable logic output
• configuration of the device after shutdown.
+5V
MAX5158/MAX5159
Low-Power, Dual, 10-Bit Voltage-Output DACs
with Serial Interface
tCSW
CS
tCSS
tCSO
tCP
tCH
tCL
tCSH
tCS1
SCLK
tDS
tDH
DIN
Figure 6. Detailed Serial-Interface Timing Diagram
SCLK
SCLK
MAX5158
MAX5159
DIN
SCLK
MAX5158
MAX5159
DOUT
CS
DIN
MAX5158
MAX5159
DOUT
CS
DIN
DOUT
CS
TO OTHER
SERIAL DEVICES
Figure 7. Daisy Chaining MAX5158/MAX5159s
DIN
SCLK
CS1
CS2
TO OTHER
SERIAL DEVICES
CS3
CS
CS
MAX5158
MAX5159
CS
MAX5158
MAX5159
MAX5158
MAX5159
SCLK
SCLK
SCLK
DIN
DIN
DIN
Figure 8. Multiple MAX5158/MAX5159s Sharing a Common DIN Line
12
______________________________________________________________________________________
Low-Power, Dual, 10-Bit, Voltage-Output DACs
with Serial Interface
MAX5158/MAX5159
Table 2. Unipolar Code Table (Gain = +2)
DAC CONTENTS
MSB
LSB
OS_
+5V/+3V
ANALOG OUTPUT
11
1111
1111 (000)
 1023 
+VREF 
 x2
 1024 
10
0000
0001 (000)
 513 
+VREF 
 x2
 1024 
10
0000
0000 (000)
 512 
+VREF 
 x 2 = VREF
 1024 
01
1111
1111 (000)
 511 
+VREF 
 x2
 1024 
00
0000
0001 (000)
 1 
+VREF 

 1024 
00
0000
0000 (000)
REF_
VDD
R
MAX5158
MAX5159
R
DAC_
OUT_
AGND
DGND
GAIN = +2V/V
Figure 9. Unipolar Output Circuit (Rail-to-Rail)
0V
Note: ( ) are for the sub bits.
OS_
+5V/+3V
REF_
Serial-Data Output
The serial-data output, DOUT, is the internal shift register’s output. DOUT allows for daisy chaining of devices
and data readback. The MAX5158/MAX5159 can be
programmed to shift data out of DOUT on SCLK’s
falling edge (Mode 0) or on the rising edge (Mode 1).
Mode 0 provides a lag of 16 clock cycles, which maintains compatibility with SPI/QSPI and Microwire interfaces. In Mode 1, the output data lags 15.5 clock
cycles. On power-up, the device defaults to Mode 0.
User-Programmable Logic Output (UPO)
UPO allows an external device to be controlled through
the serial interface (Table 1), thereby reducing the number of microcontroller I/O pins required. On power-up,
UPO is low.
PDL)
Power-Down Lockout Input (P
The power-down lockout pin (PDL) disables software
shutdown when low. When in shutdown, transitioning
PDL from high to low wakes up the part with the output
set to the state prior to shutdown. PDL can also be
used to asynchronously wake up the device.
Daisy Chaining Devices
Any number of MAX5158/MAX5159s can be daisy
chained by connecting the DOUT pin of one device to
the DIN pin of the following device in the chain (Figure 7).
Since the MAX5158/MAX5159’s DOUT pin has an internal
active pull-up, the DOUT sink/source capability determines the time required to discharge/charge a capacitive
VOS
VDD
MAX5158
MAX5159
R
R
DAC _
OUT_
AGND
DGND
Figure 10. Setting OS_ for Output Offset
load. Refer to the digital output VOH and VOL specifications in the Electrical Characteristics.
Figure 8 shows an alternate method of connecting several MAX5158/MAX5159s. In this configuration, the
data bus is common to all devices; data is not shifted
through a daisy chain. More I/O lines are required in
this configuration because a dedicated chip-select
input (CS) is required for each IC.
__________Applications Information
Unipolar Output
Figure 9 shows the MAX5158/MAX5159 configured for
unipolar, rail-to-rail operation with a gain of +2V/V. The
MAX5158 can produce a 0V to 4.096V output with a
2.048V reference (Figure 9), while the MAX5159 can
______________________________________________________________________________________
13
MAX5158/MAX5159
Low-Power, Dual, 10-Bit Voltage-Output DACs
with Serial Interface
Table 3. Bipolar Code Table
DAC CONTENTS
MSB
LSB
+5V/
+3V
11
1111
1111 (000)
 511 
+VREF 

 512 
10
0000
0001 (000)
 1 
+VREF 

 512 
10
0000
0000 (000)
01
1111
1111 (000)
 1 
-VREF 

 512 
00
0000
0001 (000)
 511 
-VREF 

 512 
00
0000
+5V/+3V
ANALOG OUTPUT
26k
AC
REFERENCE
INPUT
500mVp-p
MAX495
10k
VDD
REF
R
0V
0000 (000)
OS_
R
OUT_
DAC_
MAX5158
MAX5159
AGND
DGND
 512 

 = - VREF
 512 
-VREF
Figure 12. AC Reference Input Circuit
Note: ( ) are for the sub bits.
V+
+5V/+3V
REF_
10k
PHOTODIODE
10k
REF_
+5V/+3V
OS_
OS_
VDD
VDD
R
R
V+
MAX5158
MAX5159
R
DAC _
MAX5158
MAX5159
AGND
DAC _
DIN
10k
V-
AGND
DGND
VRPULLDOWN
Figure 13. Digital Calibration
Figure 11. Bipolar Output Circuit
produce a range of 0V to 2.5V with a 1.25V reference.
Table 2 lists the unipolar output codes. An offset to the
output can be achieved by connecting a voltage to
OS_, as shown in Figure 10. By applying VOS_ = -1V,
the output values will range between 1V and (1V +
VREF x 2).
Bipolar Output
The MAX5158/MAX5159 can be configured for a bipolar output, as shown in Figure 11. The output voltage is
given by the equation (OS_ = AGND):
VOUT = VREF [((2 x NB) / 1024) - 1]
where NB represents the numeric value of the DAC’s
binary input code. Table 3 shows digital codes and the
corresponding output voltage for Figure 11’s circuit.
14
VOUT
OUT_
µP
OUT_
DGND
R
VOUT
10k
V+
Using an AC Reference
In applications where the reference has an AC signal
component, the MAX5158/MAX5159 have multiplying
capabilities within the reference input voltage range
specifications. Figure 12 shows a technique for applying a sinusoidal input to REF_, where the AC signal is
offset before being applied to the reference input.
Harmonic Distortion and Noise
The total harmonic distortion plus noise (THD+N) is typically less than -78dB at full scale with a 1Vp-p input
swing at 5kHz. The typical -3dB frequency is 300kHz
for both devices, as shown in the Typical Operating
Characteristics.
______________________________________________________________________________________
Low-Power, Dual, 10-Bit, Voltage-Output DACs
with Serial Interface
MAX5158/MAX5159
VDD
OSA
VIN
REFA
R
OUTA
CS
SCLK
DIN
VREF
R
MAX5158
MAX5159
SHIFT
REGISTER
INPUT
REG A
DAC
REG A
DACA
INPUT
REG B
DAC
REG B
DACB
R1
R2
OUTB
REFB
VOUT
R3
R4
R
R
[ ] [ ]
= (V 2NA )( R2 )(1+ R4 ) (V
[ 1024 R1+R2 R3 ] [
VOUT = GAIN – OFFSET
OSB
IN
AGND
DGND
REF
2NB
1024
)( R4R3 )]
NA IS THE NUMERIC VALUE OF THE INPUT CODE FOR DACA.
NB IS THE NUMERIC VALUE OF THE INPUT CODE FOR DACB.
Figure 14. Digital Control of Gain and Offset
Digital Calibration and
Threshold Selection
Figure 13 shows the MAX5158/MAX5159 in a digital
calibration application. With a bright light value applied
to the photodiode (on), the DAC is digitally ramped until
it trips the comparator. The microprocessor (µP) stores
this “high” calibration value. Repeat the process with a
dim light (off) to obtain the dark current calibration. The
µP then programs the DAC to set an output voltage at
the midpoint of the two calibrated values. Applications
include tachometers, motion sensing, automatic readers, and liquid clarity analysis.
Digital Control of Gain and Offset
The two DACs can be used to control the offset and
gain for curve-fitting nonlinear functions, such as transducer linearization or analog compression/expansion
applications. The input signal is used as the reference
for the gain-adjust DAC, whose output is summed with
the output from the offset-adjust DAC. The relative
weight of each DAC output is adjusted by R1, R2, R3,
and R4 (Figure 14).
Power-Supply Considerations
On power-up, the input and DAC registers clear (set to
zero code). For rated performance, VREF_ should be at
least 1.4V below VDD. Bypass the power supply with a
4.7µF capacitor in parallel with a 0.1µF capacitor
to AGND. Minimize lead lengths to reduce lead
inductance.
Grounding and Layout Considerations
Digital and AC transient signals on AGND can create
noise at the output. Connect AGND to the highest quality
ground available. Use proper grounding techniques,
such as a multilayer board with a low-inductance ground
plane. Carefully lay out the traces between channels to
reduce AC cross-coupling and crosstalk. Wire-wrapped
boards and sockets are not recommended. If noise
becomes an issue, shielding may be required.
______________________________________________________________________________________
15
__________________Pin Configuration
_Ordering Information (continued)
PART
TOP VIEW
AGND 1
16 VDD
OUTA 2
15 OUTB
OSA 3
14 OSB
REFA 4
CL 5
MAX5158
MAX5159
13 REFB
12 PDL
CS 6
11 UPO
DIN 7
10 DOUT
9
SCLK 8
DGND
DIP/QSOP
MAX5159CPE
MAX5159CEE
MAX5159EPE
MAX5159EEE
MAX5159MJE
TEMP. RANGE
PIN-PACKAGE
0°C to +70°C
0°C to +70°C
-40°C to +85°C
-40°C to +85°C
-55°C to +125°C
16 Plastic DIP
16 QSOP
16 Plastic DIP
16 QSOP
16 CERDIP*
*Contact factory for availability.
___________________Chip Information
TRANSISTOR COUNT: 3053
SUBSTRATE CONNECTED TO AGND
________________________________________________________Package Information
QSOP.EPS
MAX5158/MAX5159
Low-Power, Dual, 13-Bit Voltage-Output DACs
with Serial Interface
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
16 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 1997 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.