MOTOROLA SEMICONDUCTOR TECHNICAL DATA 64K x 18 Bit Pipelined BurstRAM Synchronous Fast Static RAM The MCM69P618C is a 1M–bit synchronous fast static RAM designed to provide a burstable, high performance, secondary cache for the 68K Family, PowerPC, 486, i960, and Pentium microprocessors. It is organized as 64K words of 18 bits each. This device integrates input registers, an output register, a 2–bit address counter, and high speed SRAM onto a single monolithic circuit for reduced parts count in cache data RAM applications. Synchronous design allows precise cycle control with the use of an external clock (K). BiCMOS circuitry reduces the overall power consumption of the integrated functions for greater reliability. Addresses (SA), data inputs (DQx), and all control signals except output enable (G) and Linear Burst Order (LBO) are clock (K) controlled through positive–edge–triggered noninverting registers. Bursts can be initiated with either ADSP or ADSC input pins. Subsequent burst addresses can be generated internally by the MCM69P618C (burst sequence operates in linear or interleaved mode dependent upon the state of LBO) and controlled by the burst address advance (ADV) input pin. Write cycles are internally self–timed and initiated by the rising edge of the clock (K) input. This feature eliminates complex off–chip write pulse generation and provides increased timing flexibility for incoming signals. Synchronous byte write (SBx), synchronous global write (SGW), and synchronous write enable SW are provided to allow writes to either individual bytes or to both bytes. The two bytes are designated as “a” and “b”. SBa controls DQa and SBb controls DQb. Individual bytes are written if the selected byte writes SBx are asserted with SW. Both bytes are written if either SGW is asserted or if both SBx and SW are asserted. For read cycles, pipelined SRAMs output data is temporarily stored by an edge–triggered output register and then released to the output buffers at the next rising edge of clock (K). The MCM69P618C operates from a single 3.3 V power supply and all inputs and outputs are LVTTL compatible and 5 V tolerant. Order this document by MCM69P618C/D MCM69P618C TQ PACKAGE TQFP CASE 983A–01 • MCM69P618C–4 = 4 ns Access / 7.5 ns Cycle MCM69P618C–4.5 = 4.5 ns Access / 8 ns Cycle MCM69P618C–5 = 5 ns Access / 10 ns Cycle MCM69P618C–6 = 6 ns Access / 12 ns Cycle MCM69P618C–7 = 7 ns Access / 13.3 ns Cycle • Single 3.3 V + 10%, – 5% Power Supply • ADSP, ADSC, and ADV Burst Control Pins • Selectable Burst Sequencing Order (Linear/Interleaved) • Internally Self–Timed Write Cycle • Byte Write and Global Write Control • Single–Cycle Deselect Timing • 5 V Tolerant on all Pins (Inputs and I/Os) • 100–Pin TQFP Package The PowerPC name is a trademark of IBM Corp., used under license therefrom. i960 and Pentium are trademarks of Intel Corp. REV 2 2/16/98 Motorola, Inc. 1998 MOTOROLA FAST SRAM MCM69P618C 1 FUNCTIONAL BLOCK DIAGRAM LBO ADV K ADSC BURST COUNTER K2 16 64K x 18 ARRAY CLR ADSP SA SA1 SA0 2 2 ADDRESS REGISTER 16 14 SGW SW SBa 18 WRITE REGISTER a 18 2 SBb K2 SE1 SE2 SE3 G MCM69P618C 2 DATA–IN REGISTER WRITE REGISTER b ENABLE REGISTER DATA–0UT REGISTER K K ENABLE REGISTER DQa, DQb MOTOROLA FAST SRAM SA SA SE1 SE2 NC NC SBb SBa SE3 VDD VSS K SGW SW G ADSC ADSP ADV SA SA PIN ASSIGNMENT MOTOROLA FAST SRAM SA NC NC VDD VSS NC DQa DQa DQa VSS VDD DQa DQa VSS NC VDD NC DQa DQa VDD VSS DQa DQa NC NC VSS VDD NC NC NC SA SA SA SA NC NC 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 1 80 2 79 3 78 4 77 5 76 6 75 7 74 8 73 9 72 10 71 11 70 12 69 13 68 14 67 15 66 16 65 17 64 18 63 19 62 20 61 21 60 22 59 23 58 24 57 25 56 55 26 27 54 28 53 29 52 30 51 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 LBO SA SA SA SA SA1 SA0 NC NC VSS VDD NC NC SA NC NC NC VDD VSS NC NC DQb DQb VSS VDD DQb DQb NC VDD NC VSS DQb DQb VDD VSS DQb DQb DQb NC VSS VDD NC NC NC MCM69P618C 3 PIN DESCRIPTIONS Pin Locations Symbol Type 85 ADSC Input Synchronous Address Status Controller: Initiates READ, WRITE, or chip deselect cycle. 84 ADSP Input Synchronous Address Status Processor: Initiates READ, WRITE, or chip deselect cycle (exception — chip deselect does not occur when ADSP is asserted and SE1 is high). 83 ADV Input Synchronous Address Advance: Increments address count in accordance with counter type selected (linear/interleaved). (a) 58, 59, 62, 63, 68, 69, 72, 73, 74 (b) 8, 9, 12, 13, 18, 19, 22, 23, 24 DQx I/O 86 G Input Asynchronous Output Enable Input: Low — enables output buffers (DQx pins). High — DQx pins are high impedance. 89 K Input Clock: This signal registers the address, data in, and all control signals except G and LBO. 31 LBO Input Linear Burst Order Input: This pin must remain in steady state (this signal not registered or latched). It must be tied high or low. Low — linear burst counter (68K/PowerPC). High — interleaved burst counter (486/i960/Pentium). 32, 33, 34, 35, 44, 45, 46, 47, 48, 80, 81, 82, 99, 100 SA Input Synchronous Address Inputs: These inputs are registered and must meet setup and hold times. 36, 37 SA1,SA0 Input Synchronous Address Inputs: These pins must be wired to the two LSBs of the address bus for proper burst operation. These inputs are registered and must meet setup and hold times. 93, 94 (a) (b) SBx Input Synchronous Byte Write Inputs: “x” refers to the byte being written (byte a, b). SGW overrides SBx. 98 SE1 Input Synchronous Chip Enable: Active low to enable chip. Negated high–blocks ADSP or deselects chip when ADSC is asserted. 97 SE2 Input Synchronous Chip Enable: Active high for depth expansion. 92 SE3 Input Synchronous Chip Enable: Active low for depth expansion. 88 SGW Input Synchronous Global Write: This signal writes all bytes regardless of the status of the SBx and SW signals. If only byte write signals SBx are being used, tie this pin high. 87 SW Input Synchronous Write: This signal writes only those bytes that have been selected using the byte write SBx pins. If only byte write signals SBx are being used, tie this pin low. 4, 11, 15, 20, 27, 41, 54, 61, 65, 70, 77, 91 VDD Supply Power Supply: 3.3 V + 10%, – 5%. 5, 10, 17, 21, 26, 40, 55, 60, 67, 71, 76, 90 VSS Supply Ground. 64 NC Input 1, 2, 3, 6, 7, 14, 16, 25, 28, 29, 30, 38, 39, 42, 43, 49, 50, 51, 52, 53, 56, 57, 66, 75, 78, 79, 95, 96 NC — MCM69P618C 4 Description Synchronous Data I/O: “x” refers to the byte being read or written (byte a, b). No Connection: There is no connection to the chip. For compatibility reasons, it is recommended that this pin be tied low for system designs that do not have a sleep mode associated with the cache/memory controller. Other vendors’ RAMs may have implemented the Sleep Mode (ZZ) feature. No Connection: There is no connection to the chip. MOTOROLA FAST SRAM TRUTH TABLE (See Notes 1 through 4) Address Used SE1 SE2 SE3 ADSP Deselect None 1 X X Deselect None 0 X 1 Deselect None 0 0 Deselect None X Deselect None X Begin Read External 0 Begin Read Next Cycle ADSC ADV G3 DQx Write 2, 4 X 0 X X High–Z X 0 X X X High–Z X X 0 X X X High–Z X X 1 1 0 X X High–Z X 0 X 1 0 X X High–Z X 1 0 0 X X X High–Z READ External 0 1 0 1 0 X X High–Z READ Continue Read Next X X X 1 1 0 1 High–Z READ Continue Read Next X X X 1 1 0 0 DQ READ Continue Read Next 1 X X X 1 0 1 High–Z READ Continue Read Next 1 X X X 1 0 0 DQ READ Suspend Read Current X X X 1 1 1 1 High–Z READ Suspend Read Current X X X 1 1 1 0 DQ READ Suspend Read Current 1 X X X 1 1 1 High–Z READ Suspend Read Current 1 X X X 1 1 0 DQ READ Begin Write Current X X X 1 1 1 X High–Z WRITE Begin Write Current 1 X X X 1 1 X High–Z WRITE Begin Write External 0 1 0 1 0 X X High–Z WRITE Continue Write Next X X X 1 1 0 X High–Z WRITE Continue Write Next 1 X X X 1 0 X High–Z WRITE Suspend Write Current X X X 1 1 1 X High–Z WRITE Suspend Write Current 1 X X X 1 1 X High–Z WRITE NOTES: 1. X = Don’t Care. 1 = logic high. 0 = logic low. 2. Write is defined as either 1) any SBx and SW low or 2) SGW is low. 3. G is an asynchronous signal and is not sampled by the clock K. G drives the bus immediately (tGLQX) following G going low. 4. On write cycles that follow read cycles, G must be negated prior to the start of the write cycle to ensure proper write data setup times. G must also remain negated at the completion of the write cycle to ensure proper write data hold times. LINEAR BURST ADDRESS TABLE (LBO = VSS) 1st Address (External) 2nd Address (Internal) 3rd Address (Internal) X . . . X00 X . . . X01 X . . . X10 X . . . X11 X . . . X01 X . . . X10 X . . . X11 X . . . X00 X . . . X10 X . . . X11 X . . . X00 X . . . X01 X . . . X11 X . . . X00 X . . . X01 X . . . X10 4th Address (Internal) 4th Address (Internal) INTERLEAVED BURST ADDRESS TABLE (LBO = VDD) 1st Address (External) 2nd Address (Internal) 3rd Address (Internal) X . . . X00 X . . . X01 X . . . X10 X . . . X11 X . . . X01 X . . . X00 X . . . X11 X . . . X10 X . . . X10 X . . . X11 X . . . X00 X . . . X01 X . . . X11 X . . . X10 X . . . X01 X . . . X00 WRITE TRUTH TABLE SGW SW SBa SBb Read Cycle Type H H X X Read H L H H Write Byte a H L L H Write Byte b H L H L Write All Bytes H L L L Write All Bytes L X X X MOTOROLA FAST SRAM MCM69P618C 5 ABSOLUTE MAXIMUM RATINGS (See Note 1) Rating Symbol Value Unit VDD – 0.5 to + 4.6 V Vin, Vout – 0.5 to 6.0 V Iout ± 20 mA Power Supply Voltage Voltage Relative to VSS for Any Pin Except VDD Output Current (per I/O) Package Power Dissipation (See Note 2) Temperature Under Bias PD 1.6 W Tbias – 10 to 85 °C Tstg – 55 to 125 °C Storage Temperature This device contains circuitry to protect the inputs against damage due to high static voltages or electric fields; however, it is advised that normal precautions be taken to avoid application of any voltage higher than maximum rated voltages to this high–impedance circuit. NOTES: 1. Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are exceeded. Functional operation should be restricted to RECOMMENDED OPER– ATING CONDITIONS. Exposure to higher than recommended voltages for extended periods of time could affect device reliability. 2. Power dissipation capability is dependent upon package characteristics and use environment. See Package Thermal Characteristics. PACKAGE THERMAL CHARACTERISTICS Rating Symbol Max Unit Notes RθJA 40 25 °C/W 1, 2 Thermal Resistance Junction to Board (Bottom) RθJB 17 °C/W 1, 3 Thermal Resistance Junction to Case (Top) RθJC 9 °C/W 1, 4 Thermal Resistance Junction to Ambient (@ 200 lfm) Single–Layer Board Four–Layer Board NOTES: 1. Junction temperature is a function of on–chip power dissipation, package thermal resistance, mounting site (board) temperature, ambient temperature, air flow, board population, and board thermal resistance. 2. Per SEMI G38–87. 3. Indicates the average thermal resistance between the die and the printed circuit board. 4. Indicates the average thermal resistance between the die and the case top surface via the cold plate method (MIL SPEC–883 Method 1012.1). MCM69P618C 6 MOTOROLA FAST SRAM DC OPERATING CONDITIONS AND CHARACTERISTICS (VDD = 3.3 V + 10%, – 5%, TA = 0 to 70°C, Unless Otherwise Noted) RECOMMENDED OPERATING CONDITIONS (Voltages Referenced to VSS = 0 V) Parameter Symbol Min Typ Max Unit VDD 3.135 3.3 3.6 V Input Low Voltage VIL – 0.5* — 0.8 V Input High Voltage VIH 2 — 5.5** V Supply Voltage * VIL ≥ – 2 V for t ≤ tKHKH/2. ** VIH ≤ 6 V for t ≤ tKHKH/2. DC CHARACTERISTICS AND SUPPLY CURRENTS Parameter Symbol Min Max Unit Input Leakage Current (0 V ≤ Vin ≤ VDD) (Excluding LBO) Ilkg(I) — ±1 µA Output Leakage Current (0 V ≤ Vin ≤ VDD) Ilkg(O) — ±1 µA Notes AC Supply Current (Device Selected, All Outputs Open, Cycle Time ≥ tKHKH min) MCM69P618C–4 MCM69P618C–4.5 MCM69P618C–5 MCM69P618C–6 MCM69P618C–7 IDDA — 300 295 275 260 255 mA 1, 2, 3 CMOS Standby Supply Current (Deselected, Clock (K) Cycle Time ≥ tKHKH, All Inputs Toggling at CMOS Levels Vin ≤ VSS + 0.2 V or ≥ VDD – 0.2 V) MCM69P618C–4 MCM69P618C–4.5 MCM69P618C–5 MCM69P618C–6 MCM69P618C–7 ISB1 — 160 155 130 110 105 mA 4 Clock Running Supply Current (Deselected, Clock (K) Cycle Time ≥ tKHKH, All Other Inputs Held to Static CMOS Levels Vin ≤ VSS + 0.2 V or ≥ VDD – 0.2 V) MCM69P618C–4 MCM69P618C–4.5 MCM69P618C–5 MCM69P618C–6 MCM69P618C–7 ISB2 — 50 50 45 40 40 mA 4 Output Low Voltage (IOL = 8 mA) VOL — 0.4 V Output High Voltage (IOH = – 4 mA) VOH 2.4 — V NOTES: 1. Reference AC Operating Conditions and Characteristics for input and timing. 2. All addresses transition simultaneously low (LSB) and then high (MSB). 3. Data states are all zero. 4. Device in Deselected mode as defined by the Truth Table. CAPACITANCE (f = 1.0 MHz, dV = 3.0 V, TA = 25°C, Periodically Sampled Rather Than 100% Tested) Symbol Min Typ Max Unit Input Capacitance Cin — 4 6 pF Input/Output Capacitance CI/O — 7 9 pF Parameter MOTOROLA FAST SRAM MCM69P618C 7 AC OPERATING CONDITIONS AND CHARACTERISTICS (VDD = 3.3 V + 10%, – 5%, TA = 0 to 70°C, Unless Otherwise Noted) Input Timing Measurement Reference Level . . . . . . . . . . . . . . . 1.5 V Input Pulse Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to 3.0 V Input Rise/Fall Time . . . . . . . . . . . . . . . . . . . . . . 1 V/ns (20% to 80%) Output Timing Reference Level . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5 V Output Load . . . . . . . . . . . . . . See Figure 1 Unless Otherwise Noted READ/WRITE CYCLE TIMING (See Notes 1, 2, and 3) 69P618C–4 P Parameter 69P618C–4.5 69P618C–5 69P618C–6 69P618C–7 S b l Symbol Min Max Min Max Min Max Min Max Min Max U i Unit N Notes Cycle Time tKHKH 7.5 — 8 — 10 — 12 — 13.3 — ns Clock High Pulse Width tKHKL 3 — 3 — 3 — 4 — 4.5 — ns Clock Low Pulse Width tKLKH 3 — 3 — 3 — 4 — 4.5 — ns Clock Access Time tKHQV — 4 — 4.5 — 5 — 6 — 7 ns Output Enable to Output Valid tGLQV — 4 — 4.5 — 5 — 5 — 6 ns Clock High to Output Active tKHQX1 1.5 — 1.5 — 0 — 0 — 0 — ns 4 Clock High to Output Change tKHQX2 1.5 — 1.5 — 2 — 2 — 2 — ns 4 Output Enable to Output Active tGLQX 0 — 0 — 0 — 0 — 0 — ns 4 Output Disable to Q High–Z tGHQZ — 4 — 4.5 — 5 — 5 — 5 ns 4, 5 Clock High to Q High–Z tKHQZ 2 4 2 4.5 2 5 2 5 2 5 ns 4, 5 Setup Times: Address ADSP, ADSC, ADV Data In Write Chip Enable tADKH tADSKH tDVKH tWVKH tEVKH 2 — 2.5 — 2.5 — 2.5 — 2.5 — ns Hold Times: Address ADSP, ADSC, ADV Data In Write Chip Enable tKHAX tKHADSX tKHDX tKHWX tKHEX 0.5 — 0.5 — 0.5 — 0.5 — 0.5 — ns NOTES: 1. Write is defined as either any SBx and SW low or SGW is low. Chip Enable is defined as SE1 low, SE2 high and SE3 low whenever ADSP or ADSC is asserted. 2. All read and write cycle timings are referenced from K or G. 3. G is a don’t care after write cycle begins. To prevent bus contention, G should be negated prior to start of write cycle. 4. This parameter is sampled and not 100% tested. 5. Measured at ± 200 mV from steady state. OUTPUT Z0 = 50 Ω RL = 50 Ω VT = 1.5 V Figure 1. AC Test Load MCM69P618C 8 MOTOROLA FAST SRAM MOTOROLA FAST SRAM MCM69P618C 9 Q(n) B SINGLE READ tKHQX1 A Q(A) Q(B) tKHQX2 t KHQV tKHKL NOTE: E low = SE2 high and SE3 low. W low = SGW low and/or SW and SBx low. DESELECTED tKHQZ DQx G W E SE1 ADV ADSC ADSP SA K tKHKH Q(B+2) BURST READ Q(B+1) tGHQZ Q(B+3) BURST WRAPS AROUND tKLKH Q(B) C D(C) ADSP, SA SE2, SE3 IGNORED READ/WRITE CYCLES D(C+2) BURST WRITE D(C+1) D(C+3) tGLQX D SINGLE READ Q(D) t KHQV APPLICATION INFORMATION The MCM69P618C BurstRAM is a high speed synchronous SRAM that is intended for use primarily in secondary or level two (L2) cache memory applications. L2 caches are found in a variety of classes of computers — from the desktop personal computer to the high–end servers and transaction processing machines. For simplicity, the majority of L2 caches today are direct mapped and are single bank implementations. These caches tend to be designed for bus speeds in the range of 33 to 66 MHz. At these bus rates, non–pipelined (flow–through) BurstRAMs can be used since their access times meet the speed requirements for a minimum–latency, zero–wait state L2 cache interface. Latency is a measure (time) of “dead” time the memory system exhibits as a result of a memory request. For those applications that demand bus operation at greater than 66 MHz or multi–bank L2 caches at 66 MHz, the pipelined (register/register) version of the 64K x 18 BurstRAM (MCM69P618C) allows the user to configure the RAM to support such designs. Multiple banks of BurstRAMs create additional bus loading and can cause the system to otherwise miss its timing requirements. The access time (clock– to–valid–data) of a pipelined BurstRAM is inherently faster than a non–pipelined device by a few nanoseconds. This does not come without cost. The cost is latency — “dead” time. Since most L2 caches are tied to the processor bus and bus speeds continue to increase over time, pipelined (R/R) BurstRAMs are the best choice in achieving zero–wait state L2 cache performance. At bus speeds ranging from 66 MHz to 100 MHz, pipelined BurstRAMs are able to provide fast clock to valid data times required of these high speed buses. NON–BURST SYNCHRONOUS OPERATION Although this BurstRAM has been designed for 68K–, PowerPC–, 486–, i960–, and Pentium–based systems, these SRAMs can be used in other high speed L2 cache or memory applications that do not require the burst address feature. Most L2 caches designed with a synchronous interface can make use of the MCM69P618C. The burst counter feature of the BurstRAM can be disabled, and the SRAM can be configured to act upon a continuous stream of addresses. See Figure 2. CONTROL PIN TIE VALUES EXAMPLE (H ≥ VIH, L ≤ VIL) Non–Burst ADSP ADSC ADV SE1 SE2 LBO Sync Non–Burst, Pipelined SRAM H L H L H X NOTE: Although X is specified in the table as a don’t care, the pin must be tied either high or low. K ADDR A B C D E F G H SE3 W G DQ Q(A) Q(B) Q(C) Q(D) D(E) D(F) READS D(G) D(H) WRITES Figure 2. Example Configuration as Non–Burst Synchronous SRAM MCM69P618C 10 MOTOROLA FAST SRAM ORDERING INFORMATION (Order by Full Part Number) MCM 69P618C XX X X Motorola Memory Prefix Blank = Trays, R = Tape and Reel Part Number Speed (4 = 4 ns, 4.5 = 4.5 ns, 5 = 5 ns, 6 = 6 ns, 7 = 7 ns) Package (TQ = TQFP) Full Part Numbers — MCM69P618CTQ4 MCM69P618CTQ4.5 MCM69P618CTQ5 MCM69P618CTQ6 MCM69P618CTQ7 MCM69P618CTQ4R MCM69P618CTQ4.5R MCM69P618CTQ5R MCM69P618CTQ6R MCM69P618CTQ7R Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. MOTOROLA FAST SRAM MCM69P618C 11 PACKAGE DIMENSIONS TQ PACKAGE TQFP CASE 983A–01 e 4X 0.20 (0.008) H A–B D 2X 30 TIPS e/2 0.20 (0.008) C A–B D –D– 80 51 B 50 81 –A– –X– B E/2 X=A, B, OR D –B– VIEW Y E1 E BASE METAL PLATING b1 E1/2 c 31 100 1 30 D1/2 0.13 (0.005) 0.20 (0.008) C A–B D A q 2 0.10 (0.004) C –H– –C– SEATING PLANE q 3 VIEW AB S S q C A–B S D S R2 A2 L2 L L1 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DATUM PLANE –H– IS LOCATED AT BOTTOM OF LEAD AND IS COINCIDENT WITH THE LEAD WHERE THE LEAD EXITS THE PLASTIC BODY AT THE BOTTOM OF THE PARTING LINE. 4. DATUMS –A–, –B– AND –D– TO BE DETERMINED AT DATUM PLANE –H–. 5. DIMENSIONS D AND E TO BE DETERMINED AT SEATING PLANE –C–. 6. DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE PROTRUSION IS 0.25 (0.010) PER SIDE. DIMENSIONS D1 AND B1 DO INCLUDE MOLD MISMATCH AND ARE DETERMINED AT DATUM PLANE –H–. 7. DIMENSION b DOES NOT INCLUDE DAMBAR PROTRUSION. DAMBAR PROTRUSION SHALL NOT CAUSE THE b DIMENSION TO EXCEED 0.45 (0.018). 1 0.25 (0.010) R1 M SECTION B–B 2X 20 TIPS A1 c1 b D/2 D1 D 0.05 (0.002) ÉÉÉÉ ÇÇÇÇ ÇÇÇÇ ÉÉÉÉ GAGE PLANE q VIEW AB DIM A A1 A2 b b1 c c1 D D1 E E1 e L L1 L2 S R1 R2 q q q q 1 2 3 MILLIMETERS MIN MAX ––– 1.60 0.05 0.15 1.35 1.45 0.22 0.38 0.22 0.33 0.09 0.20 0.09 0.16 22.00 BSC 20.00 BSC 16.00 BSC 14.00 BSC 0.65 BSC 0.45 0.75 1.00 REF 0.50 REF 0.20 ––– 0.08 ––– 0.08 0.20 0_ 7_ 0_ ––– 11 _ 13 _ 11 _ 13 _ INCHES MIN MAX ––– 0.063 0.002 0.006 0.053 0.057 0.009 0.015 0.009 0.013 0.004 0.008 0.004 0.006 0.866 BSC 0.787 BSC 0.630 BSC 0.551 BSC 0.026 BSC 0.018 0.030 0.039 REF 0.020 REF 0.008 ––– 0.003 ––– 0.003 0.008 0_ 7_ 0_ ––– 11 _ 13 _ 11 _ 13 _ Mfax is a trademark of Motorola, Inc. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado, 80217. 1-303-675-2140 or 1-800-441-2447 JAPAN: Nippon Motorola Ltd.: SPD, Strategic Planning Office, 141, 4-32-1 Nishi-Gotanda, Shagawa-ku, Tokyo, Japan. 03-5487-8488 Mfax : [email protected] – TOUCHTONE 1-602-244-6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, Motorola Fax Back System – US & Canada ONLY 1-800-774-1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298 – http://sps.motorola.com /mfax / HOME PAGE : http://motorola.com/sps / CUSTOMER FOCUS CENTER: 1-800-521-6274 MCM69P618C 12 ◊ MOTOROLAMCM69P618C/D FAST SRAM