MICROCHIP MCP3221A6T-E/OT

MCP3221
Low Power 12-Bit A/D Converter With I2C™ Interface
Features
Description
•
•
•
•
•
The Microchip Technology Inc. MCP3221 is a
successive approximation A/D converter with 12-bit
resolution. Available in the SOT-23-5 package, this
device provides one single-ended input with very low
power consumption. Based on an advanced CMOS
technology, the MCP3221 provides a low maximum
conversion current and standby current of 250 µA and
1 µA, respectively. Low current consumption,
combined with the small SOT-23 package, make this
device ideal for battery-powered and remote data
acquisition applications.
•
•
•
•
•
•
•
•
12-bit resolution
±1 LSB DNL, ±2 LSB INL max.
250 µA max conversion current
5 nA typical standby current, 1 µA max.
I2C™-compatible serial interface
- 100 kHz I2C Standard Mode
- 400 kHz I2C Fast Mode
Up to 8 devices on a single 2-Wire bus
22.3 ksps in I2C Fast Mode
Single-ended analog input channel
On-chip sample and hold
On-chip conversion clock
Single-supply specified operation: 2.7V to 5.5V
Temperature range:
- Industrial: -40°C to +85°C
- Extended: -40°C to +125°C
Small SOT-23-5 package
Applications
•
•
•
•
•
Data Logging
Multi-zone Monitoring
Hand-Held Portable Applications
Battery-Powered Test Equipment
Remote or Isolated Data Acquisition
Communication to the MCP3221 is performed using a
2-wire, I2C compatible interface. Standard (100 kHz)
and Fast (400 kHz) I2C modes are available with the
device. An on-chip conversion clock enables
independent timing for the I2C and conversion clocks.
The device is also addressable, allowing up to eight
devices on a single 2-wire bus.
The MCP3221 runs on a single supply voltage that
operates over a broad range of 2.7V to 5.5V. This
device also provides excellent linearity of ±1 LSB
differential non-linearity and ±2 LSB integral non-linearity, maximum.
Functional Block Diagram
VDD
VSS
Package Type
DAC
5-Pin SOT-23
VSS 2
5
SCL
MCP3221
VDD 1
AIN
–
Sample
and
Hold
Comparator
+
Clock
Control Logic
AIN 3
12-bit SAR
I2C™ Interface
4 SDA
SCL
© 2006 Microchip Technology Inc.
SDA
DS21732C-page 1
MCP3221
1.0
ELECTRICAL
CHARACTERISTICS
† Stresses above those listed under “Maximum ratings” may
cause permanent damage to the device. This is a stress rating
only and functional operation of the device at those or any
other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum
rating conditions for extended periods may affect device
reliability.
Absolute Maximum Ratings †
VDD...................................................................................7.0V
Analog input pin w.r.t. VSS .......... ............. -0.6V to VDD +0.6V
SDA and SCL pins w.r.t. VSS........... .........-0.6V to VDD +1.0V
Storage temperature .....................................-65°C to +150°C
Ambient temp. with power applied ................-65°C to +125°C
Maximum Junction Temperature .......... .........................150°C
ESD protection on all pins (HBM) .................................≥ 4 kV
DC ELECTRICAL SPECIFICATIONS
Electrical Characteristics: Unless otherwise noted, all parameters apply at VDD = 5.0V, VSS = GND, RPU = 2 kΩ
TAMB = -40°C to +85°C, I2C Fast Mode Timing: fSCL = 400 kHz (Note 3).
Parameters
Sym
Min
Typ
Max
Units
Conditions
DC Accuracy
Resolution
12
bits
Integral Nonlinearity
INL
—
±0.75
±2
LSB
Differential Nonlinearity
DNL
—
±0.5
±1
LSB
Offset Error
—
±0.75
±2
LSB
Gain Error
—
-1
±3
LSB
—
-82
—
dB
No missing codes
Dynamic Performance
Total Harmonic Distortion
THD
VIN = 0.1V to 4.9V @ 1 kHz
Signal-to-Noise and Distortion
SINAD
—
72
—
dB
VIN = 0.1V to 4.9V @ 1 kHz
Spurious-Free Dynamic Range
SFDR
—
86
—
dB
VIN = 0.1V to 4.9V @ 1 kHz
VSS-0.3
—
VDD+0.3
V
2.7V ≤ VDD ≤ 5.5V
-1
—
+1
µA
V
Analog Input
Input Voltage Range
Leakage Current
SDA/SCL (open-drain output):
Data Coding Format
High-level input voltage
Straight Binary
VIH
0.7 VDD
—
—
Low-level input voltage
VIL
—
—
0.3 VDD
V
Low-level output voltage
VOL
—
—
0.4
V
Hysteresis of Schmitt trigger inputs
IOL = 3 mA, RPU = 1.53 kΩ
VHYST
—
0.05 VDD
—
V
fSCL = 400 kHz only
Input leakage current
ILI
-1
—
+1
µA
VIN = 0.1 VDD and 0.9 VDD
Output leakage current
ILO
-1
—
+1
µA
VOUT = 0.1 VSS and
0.9 VDD
CIN,
COUT
—
—
10
pF
TAMB = 25°C, f = 1 MHz;
(Note 2)
CB
—
—
400
pF
SDA drive low, 0.4V
Pin capacitance
(all inputs/outputs)
Bus Capacitance
Note 1:
2:
3:
4:
5:
“Sample time” is the time between conversions once the address byte has been sent to the converter.
Refer to Figure 5-6.
This parameter is periodically sampled and not 100% tested.
RPU = Pull-up resistor on SDA and SCL.
SDA and SCL = VSS to VDD at 400 kHz.
tACQ and tCONV are dependent on internal oscillator timing. See Figure 5-5 and Figure 5-6 for relation to
SCL.
DS21732C-page 2
© 2006 Microchip Technology Inc.
MCP3221
DC ELECTRICAL SPECIFICATIONS (CONTINUED)
Electrical Characteristics: Unless otherwise noted, all parameters apply at VDD = 5.0V, VSS = GND, RPU = 2 kΩ
TAMB = -40°C to +85°C, I2C Fast Mode Timing: fSCL = 400 kHz (Note 3).
Parameters
Sym
Min
Typ
Max
Units
Conditions
Operating Voltage
VDD
2.7
—
5.5
V
Conversion Current
IDD
—
175
250
µA
Standby Current
IDDS
—
0.005
1
µA
SDA, SCL = VDD
Active bus current
IDDA
—
—
120
µA
Note 4
tCONV
—
8.96
—
µs
Note 5
Analog Input Acquisition Time
tACQ
—
1.12
—
µs
Note 5
Sample Rate
fSAMP
—
—
22.3
ksps
Power Requirements
Conversion Rate
Conversion Time
Note 1:
2:
3:
4:
5:
fSCL = 400 kHz (Note 1)
“Sample time” is the time between conversions once the address byte has been sent to the converter.
Refer to Figure 5-6.
This parameter is periodically sampled and not 100% tested.
RPU = Pull-up resistor on SDA and SCL.
SDA and SCL = VSS to VDD at 400 kHz.
tACQ and tCONV are dependent on internal oscillator timing. See Figure 5-5 and Figure 5-6 for relation to
SCL.
TEMPERATURE SPECIFICATIONS
Electrical Characteristics: Unless otherwise noted, all parameters apply at VDD = 5.0V, VSS = GND.
Parameters
Symbol
Min
Typ
Max
Units
Conditions
Temperature Ranges
Industrial Temperature Range
TA
-40
—
+85
°C
Extended Temperature Range
TA
-40
—
+125
°C
Operating Temperature Range
TA
-40
—
+125
°C
Storage Temperature Range
TA
-65
—
+150
°C
θJA
—
256
—
°C/W
Thermal Package Resistances
Thermal Resistance, 5L-SOT23
© 2006 Microchip Technology Inc.
DS21732C-page 3
MCP3221
TIMING SPECIFICATIONS
Electrical Characteristics: All parameters apply at VDD = 2.7V - 5.5V, VSS = GND, TAMB = -40°C to +85°C.
Parameters
I2 C
Sym
Min
Typ
Max
Units
Conditions
Standard Mode
Clock frequency
fSCL
0
—
100
kHz
Clock high time
THIGH
4000
—
—
ns
Clock low time
TLOW
4700
—
—
ns
TR
—
—
1000
ns
From VIL to VIH (Note 1)
From VIL to VIH (Note 1)
SDA and SCL rise time
TF
—
—
300
ns
THD:STA
4000
—
—
ns
START condition setup time
TSU:STA
4700
—
—
ns
Data input setup time
TSU:DAT
250
—
—
ns
STOP condition setup time
TSU:STO
4000
—
—
ns
STOP condition hold time
THD:STD
4000
—
—
ns
SDA and SCL fall time
START condition hold time
Output valid from clock
TAA
—
—
3500
ns
Bus free time
TBUF
4700
—
—
ns
Note 2
Input filter spike suppression
TSP
—
—
50
ns
SDA and SCL pins (Note 1)
I2C Fast Mode
Clock frequency
FSCL
0
—
400
kHz
Clock high time
THIGH
600
—
—
ns
Clock low time
TLOW
1300
—
—
ns
TR
20 + 0.1CB
—
300
ns
From VIL to VIH (Note 1)
From VIL to VIH (Note 1)
SDA and SCL rise time
TF
20 + 0.1CB
—
300
ns
THD:STA
600
—
—
ns
START condition setup time
TSU:STA
600
—
—
ns
Data input hold time
THD:DAT
0
—
0.9
ms
Data input setup time
TSU:DAT
100
—
—
ns
STOP condition setup time
TSU:STO
600
—
—
ns
STOP condition hold time
SDA and SCL fall time
START condition hold time
THD:STD
600
—
—
ns
Output valid from clock
TAA
—
—
900
ns
Bus free time
TBUF
1300
—
—
ns
Note 2
Input filter spike suppression
TSP
—
—
50
ns
SDA and SCL pins (Note 1)
Note 1:
2:
This parameter is periodically sampled and not 100% tested.
Time the bus must be free before a new transmission can start.
THIGH
TF
SCL
SDA
IN
SDA
OUT
FIGURE 1-1:
DS21732C-page 4
VHYS
TR
TSU:STA
TLOW
TSP
THD:DAT
TSU:DAT
TSU:STO
THD:STA
TAA
TBUF
Standard and Fast Mode Bus Timing Data.
© 2006 Microchip Technology Inc.
MCP3221
2.0
TYPICAL PERFORMANCE CURVES
Note:
The graphs and tables provided following this note are a statistical summary based on a limited number of
samples and are provided for informational purposes only. The performance characteristics listed herein
are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified
operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
1
0.8
0.6
0.4
0.2
0
-0.2
-0.4
-0.6
-0.8
-1
Negative INL
0
100
FIGURE 2-1:
INL (LSB)
INL (LSB)
Positive INL
200
300
I2C Bus Rate (kHz)
3.5
4
VDD (V)
4.5
5
200
300
400
INL vs. Clock Rate
1
0.8
0.6
0.4
0.2
0
-0.2
-0.4
-0.6
-0.8
-1
Positive INL
Negative INL
2.5
5.5
3
3.5
4
4.5
5
5.5
VDD (V)
FIGURE 2-2:
INL vs. VDD - I2C™
Standard Mode (fSCL = 100 kHz).
FIGURE 2-5:
INL vs. VDD - I2C™ Fast
Mode (fSCL = 400 kHz).
2
2
1.5
1.5
1
INL (LSB)
1
INL (LSB)
100
FIGURE 2-4:
(VDD = 2.7V).
Negative INL
3
Negative INL
0
Positive INL
2.5
Positive INL
I2C Bus Rate (kHz)
INL vs. Clock Rate.
1
0.8
0.6
0.4
0.2
0
-0.2
-0.4
-0.6
-0.8
-1
1
0.8
0.6
0.4
0.2
0
-0.2
-0.4
-0.6
-0.8
-1
400
INL (LSB)
INL (LSB)
Note: Unless otherwise indicated, VDD = 5V, VSS = 0V, I2C Fast Mode Timing (SCL = 400 kHz), Continuous Conversion
Mode (fSAMP = 22.3 ksps), TA = +25°C.
0.5
0
-0.5
0.5
0
-0.5
-1
-1
-1.5
-1.5
-2
-2
0
1024
2048
Digital Code
FIGURE 2-3:
INL vs. Code
(Representative Part).
© 2006 Microchip Technology Inc.
3072
4096
0
1024
2048
3072
4096
Digital Code
FIGURE 2-6:
INL vs. Code
(Representative Part, VDD = 2.7V).
DS21732C-page 5
MCP3221
1
0.8
0.6
0.4
0.2
0
-0.2
-0.4
-0.6
-0.8
-1
Positive INL
INL (LSB)
INL (LSB)
Note: Unless otherwise indicated, VDD = 5V, VSS = 0V, I2C Fast Mode Timing (SCL = 400 kHz), Continuous Conversion
Mode (fSAMP = 22.3 ksps), TA = +25°C.
Negative INL
-50
-25
0
25
50
75
100
1
0.8
0.6
0.4
0.2
0
-0.2
-0.4
-0.6
-0.8
-1
125
Positive INL
Negative INL
-50
-25
0
Temperature (°C)
INL vs. Temperature.
1
0.8
0.6
0.4
0.2
0
-0.2
-0.4
-0.6
-0.8
-1
FIGURE 2-10:
(VDD = 2.7V).
Positive DNL
DNL (LSB)
DNL (LSB)
FIGURE 2-7:
Negative DNL
0
100
200
300
1
0.8
0.6
0.4
0.2
0
-0.2
-0.4
-0.6
-0.8
-1
400
100
4
VDD (V)
DNL (LSB)
FIGURE 2-11:
(VDD = 2.7V).
DNL (LSB)
4.5
5
FIGURE 2-9:
DNL vs. VDD - I2C™
Standard Mode (fSCL = 100 kHz).
DS21732C-page 6
200
300
400
I C Bus Rate (kHz)
Negative DNL
3.5
125
2
DNL vs. Clock Rate.
3
100
Negative DNL
0
Positive DNL
2.5
75
Positive DNL
2
1
0.8
0.6
0.4
0.2
0
-0.2
-0.4
-0.6
-0.8
-1
50
INL vs. Temperature
I C Bus Rate (kHz)
FIGURE 2-8:
25
Temperature (°C)
5.5
DNL vs. Clock Rate
1
0.8
0.6
0.4
0.2
0
-0.2
-0.4
-0.6
-0.8
-1
Positive DNL
Negative DNL
2.5
3
3.5
4
4.5
5
5.5
VDD (V)
FIGURE 2-12:
DNL vs. VDD - I2C™ Fast
Mode (fSCL = 400 kHz).
© 2006 Microchip Technology Inc.
MCP3221
1
0.8
0.6
0.4
0.2
0
-0.2
-0.4
-0.6
-0.8
-1
DNL (LSB)
DNL (LSB)
Note: Unless otherwise indicated, VDD = 5V, VSS = 0V, I2C Fast Mode Timing (SCL = 400 kHz), Continuous Conversion
Mode (fSAMP = 22.3 ksps), TA = +25°C.
0
1024
2048
3072
1
0.8
0.6
0.4
0.2
0
-0.2
-0.4
-0.6
-0.8
-1
0
4096
1024
2048
FIGURE 2-16:
DNL vs. Code
(Representative Part, VDD = 2.7V).
Positive DNL
DNL (LSB)
DNL (LSB)
FIGURE 2-13:
DNL vs. Code
(Representative Part).
Negative DNL
-50
-25
0
25
50
75
100
125
1
0.8
0.6
0.4
0.2
0
-0.2
-0.4
-0.6
-0.8
-1
Positive DNL
Negative DNL
-50
-25
Temperature (°C)
0
-0.1
-0.2
-0.3
-0.4
-0.5
-0.6
-0.7
-0.8
-0.9
-1
DNL vs. Temperature.
Fast Mode
(fSCL= 100 kHz)
2.5
3
3.5
4.5
5
VDD (V)
FIGURE 2-15:
FIGURE 2-17:
(VDD = 2.7V).
Standard Mode
(fSCL= 400 kHz)
4
Gain Error vs. VDD.
© 2006 Microchip Technology Inc.
0
25
50
75
100
125
Temperature (°C)
Offset Error (LSB)
Gain Error (LSB)
FIGURE 2-14:
4096
Digital Code
Digital Code
1
0.8
0.6
0.4
0.2
0
-0.2
-0.4
-0.6
-0.8
-1
3072
5.5
DNL vs. Temperature
1
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
fSCL = 100 kHz & 400 kHz
2.5
3
FIGURE 2-18:
3.5
4
VDD (V)
4.5
5
5.5
Offset Error vs. VDD.
DS21732C-page 7
MCP3221
Note: Unless otherwise indicated, VDD = 5V, VSS = 0V, I2C Fast Mode Timing (SCL = 400 kHz), Continuous Conversion
Mode (fSAMP = 22.3 ksps), TA = +25°C.
3
Offset Error (LSB)
Gain Error (LSB)
2
VDD = 2.7V
1
0
-1
-2
VDD = 5V
-3
-50
-25
0
25
50
75
100
2
1.8
1.6
1.4
1.2
1
0.8
0.6
0.4
0.2
0
VDD = 5V
VDD = 2.7V
-50
125
-25
0
Gain Error vs. Temperature.
100
90
80
70
60
50
40
30
20
10
0
FIGURE 2-22:
Temperature.
VDD = 5V
SINAD (dB)
SNR (dB)
FIGURE 2-19:
VDD = 2.7V
1
10
75
100
125
VDD = 5V
VDD = 2.7V
1
10
Input Frequency (kHz)
SNR vs. Input Frequency.
FIGURE 2-23:
SINAD vs. Input Frequency.
80
VDD = 5V
70
60
SINAD (dB)
THD (dB)
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
50
Offset Error vs.
100
90
80
70
60
50
40
30
20
10
0
Input Frequency (kHz)
FIGURE 2-20:
25
Temperature (°C)
Temperature (°C)
VDD = 5V
VDD = 2.7V
50
VDD = 2.7V
40
30
20
10
0
1
10
-40
Input Frequency (kHz)
FIGURE 2-21:
DS21732C-page 8
THD vs. Input Frequency.
-30
-20
-10
0
Input Signal Level (dB)
FIGURE 2-24:
Level.
SINAD vs. Input Signal
© 2006 Microchip Technology Inc.
MCP3221
12
11.95
11.9
11.85
11.8
11.75
11.7
11.65
11.6
11.55
11.5
12
11.5
ENOB (rms)
VDD = 5V
10.5
10
9.5
9
2.5
3
FIGURE 2-25:
SFDR (dB)
VDD = 2.7V
11
100
90
80
70
60
50
40
30
20
10
0
3.5
4
VDD (V)
4.5
5
5.5
1
10
Input Frequency (kHz)
FIGURE 2-28:
ENOB vs. VDD.
fSAMP = 5.6 ksps
-10
VDD = 2.7V
-30
-50
-70
-90
-110
-130
1
0
10
500
FIGURE 2-26:
SFDR vs. Input Frequency.
250
-10
200
IDD (µA)
-30
-70
-90
1500
2000
2500
FIGURE 2-29:
Spectrum Using I2C™
Standard Mode (Representative Part, 1 kHz
Input Frequency).
10
-50
1000
Frequency (Hz)
Input Frequency (kHz)
Amplitude (dB)
ENOB vs. Input Frequency.
10
VDD = 5V
Amplitude (dB)
ENOB (rms)
Note: Unless otherwise indicated, VDD = 5V, VSS = 0V, I2C Fast Mode Timing (SCL = 400 kHz), Continuous Conversion
Mode (fSAMP = 22.3 ksps), TA = +25°C.
150
100
50
-110
0
-130
0
2000
4000
6000
8000
10000
2.5
3
FIGURE 2-27:
Spectrum Using I2C™ Fast
Mode (Representative Part, 1 kHz Input
Frequency).
© 2006 Microchip Technology Inc.
3.5
4
4.5
5
5.5
VDD (V)
Frequency (Hz)
FIGURE 2-30:
IDD (Conversion) vs. VDD.
DS21732C-page 9
MCP3221
200
180
160
140
120
100
80
60
40
20
0
100
90
80
70
60
50
40
30
20
10
0
IDDA (µA)
IDD (µA)
Note: Unless otherwise indicated, VDD = 5V, VSS = 0V, I2C Fast Mode Timing (SCL = 400 kHz), Continuous Conversion
Mode (fSAMP = 22.3 ksps), TA = +25°C.
VDD = 5V
VDD = 2.7V
0
100
200
300
2
I C Clock Rate (kHz)
FIGURE 2-31:
Rate.
0
IDDA (µA)
IDD (µA)
VDD = 5V
150
VDD = 2.7V
50
0
-50
-25
0
25
50
75
100
100
125
VDD = 5V
VDD = 2.7V
-50
-25
0
25
50
75
100
125
Temperature (°C)
IDD (Conversion) vs.
FIGURE 2-35:
Temperature.
100
90
80
70
60
50
40
30
20
10
0
IDDA (Active Bus) vs.
60
50
IDDS (pA)
IDDA (µA)
400
IDDA (Active Bus) vs. Clock
100
90
80
70
60
50
40
30
20
10
0
Temperature (°C)
FIGURE 2-32:
Temperature.
200
300
2
I C Clock Rate (kHz)
FIGURE 2-34:
Rate.
250
100
VDD = 2.7V
400
IDD (Conversion) vs. Clock
200
VDD = 5V
40
30
20
10
0
2.5
3
3.5
4
4.5
5
5.5
2.5
3
VDD (V)
FIGURE 2-33:
DS21732C-page 10
IDDA (Active Bus) vs. VDD.
3.5
4
4.5
5
5.5
VDD (V)
FIGURE 2-36:
IDDS (Standby) vs. VDD.
© 2006 Microchip Technology Inc.
MCP3221
Note: Unless otherwise indicated, VDD = 5V, VSS = 0V, I2C Fast Mode Timing (SCL = 400 kHz), Continuous Conversion
Mode (fSAMP = 22.3 ksps), TA = +25°C.
2.1
Test Circuits
1000
100
VDD = 5V
IDDS (nA)
10
1
0.1
10 µF
0.01
2 kΩ
0.001
0.0001
-50
-25
0
25
50
75
100
Analog Input Leakage (nA)
FIGURE 2-37:
Temperature.
AIN
125
Temperature (°C)
VIN
VDDSDA
MCP3221
VSS SCL
VCM = 2.5V
FIGURE 2-39:
-25
2 kΩ
IDDS (Standby) vs.
2
1.8
1.6
1.4
1.2
1
0.8
0.6
0.4
0.2
0
-50
0.1 µF
0
25
50
75
100
Typical Test Configuration.
125
Temperature (°C)
FIGURE 2-38:
Temperature.
Analog Input Leakage vs.
© 2006 Microchip Technology Inc.
DS21732C-page 11
MCP3221
3.0
PIN FUNCTIONS
TABLE 3-1:
PIN FUNCTION TABLE
Name
3.1
Function
VDD
+2.7V to 5.5V Power Supply
VSS
Ground
AIN
Analog Input
SDA
Serial Data In/Out
SCL
Serial Clock In
VDD and VSS
The VDD pin, with respect to VSS, provides power to the
device as well as a voltage reference for the conversion
process. Refer to Section 6.4 “Device Power and
Layout Considerations”, “Device Power and Layout
Considerations”, for tips on power and grounding.
3.2
Analog Input (AIN)
AIN is the input pin to the sample-and-hold circuitry of
the Successive Approximation Register (SAR) converter. Care should be taken in driving this pin. Refer to
Section 6.1 “Driving the Analog Input”, “Driving the
Analog Input”. For proper conversions, the voltage on
this pin can vary from VSS to VDD.
DS21732C-page 12
3.3
Serial Data (SDA)
SDA is a bidirectional pin used to transfer addresses
and data into and out of the device. Since it is an opendrain terminal, the SDA bus requires a pull-up resistor
to VDD (typically 10 kΩ for 100 kHz and 2 kΩ for
400 kHz SCL clock speeds). Refer to Section 6.2
“Connecting to the I2C Bus”, “Connecting to the I2C
Bus”, for more information.
For normal data transfer, SDA is allowed to change only
during SCL low. Changes during SCL high are reserved
for indicating the START and STOP conditions. Refer to
Section 5.1 “I2C Bus Characteristics”, “I2C Bus
Characteristics”.
3.4
Serial Clock (SCL)
SCL is an input pin used to synchronize the data transfer to and from the device on the SDA pin and is an
open-drain terminal. Therefore, the SCL bus requires a
pull-up resistor to VDD (typically 10 kΩ for 100 kHz and
2 kΩ for 400 kHz SCL clock speeds. Refer to
Section 6.2 “Connecting to the I2C Bus”, “Connecting to the I2C Bus”).
For normal data transfer, SDA is allowed to change
only during SCL low. Changes during SCL high are
reserved for indicating the START and STOP
conditions. Refer to Section 6.1 “Driving the Analog
Input”, “Driving the Analog Input”.
© 2006 Microchip Technology Inc.
MCP3221
4.0
DEVICE OPERATION
4.2
The MCP3221 employs a classic SAR architecture.
This architecture uses an internal sample and hold
capacitor to store the analog input while the conversion
is taking place. At the end of the acquisition time, the
input switch of the converter opens and the device uses
the collected charge on the internal sample-and-hold
capacitor to produce a serial 12-bit digital output code.
The acquisition time and conversion is self-timed using
an internal clock. After each conversion, the results are
stored in a 12-bit register that can be read at any time.
Communication with the device is accomplished with a
2-wire, I2C interface. Maximum sample rates of
22.3 ksps are possible with the MCP3221 in a continuous-conversion mode and an SCL clock rate of
400 kHz.
4.1
Digital Output Code
The digital output code produced by the MCP3221 is a
function of the input signal and power supply voltage,
VDD. As the VDD level is reduced, the LSB size is
reduced accordingly. The theoretical LSB size is shown
below.
EQUATION
V DD
LSB SIZE = -----------4096
VDD = Supply voltage
The output code of the MCP3221 is transmitted serially
with MSB first. The format of the code is straight binary.
Conversion Time (tCONV)
The conversion time is the time required to obtain the
digital result once the analog input is disconnected
from the holding capacitor. With the MCP3221, the
specified conversion time is typically 8.96 µs. This time
is dependent on the internal oscillator and is
independent of SCL.
4.3
Acquisition Time (tACQ)
The acquisition time is the amount of time the sample
cap array is acquiring charge.
The acquisition time is, typically, 1.12 µs. This time is
dependent on the internal oscillator and independent of
SCL.
4.4
Sample Rate
Sample rate is the inverse of the maximum amount of
time that is required from the point of acquisition of the
first conversion to the point of acquisition of the second
conversion.
The sample rate can be measured either by single or
continuous conversions. A single conversion includes
a Start Bit, Address Byte, Two Data Bytes and a Stop
bit. This sample rate is measured from one Start Bit to
the next Start Bit.
For continuous conversions (requested by the Master
by issuing an acknowledge after a conversion), the
maximum sample rate is measured from conversion to
conversion or a total of 18 clocks (two data bytes and
two Acknowledge bits). Refer to Section 5.2 “Device
Addressing”, “Device Addressing”.
Output Code
1111 1111 1111
1111 1111 1110
(4095)
(4094)
0000 0000 0011 (3)
0000 0000 0010 (2)
0000 0000 0001 (1)
0000 0000 0000 (0)
.5 LSB
1.5 LSB
2.5 LSB
FIGURE 4-1:
AIN
VDD-1.5 LSB
VDD-2.5 LSB
Transfer Function.
© 2006 Microchip Technology Inc.
DS21732C-page 13
MCP3221
4.5
Differential Non-Linearity (DNL)
In the ideal A/D converter transfer function, each code
has a uniform width. That is, the difference in analog
input voltage is constant from one code transition point
to the next. Differential nonlinearity (DNL) specifies the
deviation of any code in the transfer function from an
ideal code width of 1 LSB. The DNL is determined by
subtracting the locations of successive code transition
points after compensating for any gain and offset
errors. A positive DNL implies that a code is longer than
the ideal code width, while a negative DNL implies that
a code is shorter than the ideal width.
4.6
Integral Non-Linearity (INL)
Integral nonlinearity (INL) is a result of cumulative DNL
errors and specifies how much the overall transfer
function deviates from a linear response. The method
of measurement used in the MCP3221 A/D converter
to determine INL is the “end-point” method.
4.7
Offset Error
Offset error is defined as a deviation of the code transition points that are present across all output codes.
This has the effect of shifting the entire A/D transfer
function. The offset error is measured by finding the difference between the actual location of the first code
transition and the desired location of the first transition.
The ideal location of the first code transition is located
at 1/2 LSB above VSS.
4.8
Gain Error
The gain error determines the amount of deviation from
the ideal slope of the A/D converter transfer function.
Before the gain error is determined, the offset error is
measured and subtracted from the conversion result.
The gain error can then be determined by finding the
location of the last code transition and comparing that
location to the ideal location. The ideal location of the
last code transition is 1.5 LSBs below full-scale or VDD.
4.9
Conversion Current (IDD)
The average amount of current over the time required
to perform a 12-bit conversion.
4.10
Active Bus Current (IDDA)
The average amount of current over the time required
to monitor the I2C bus. Any current the device consumes while it is not being addressed is referred to as
“Active Bus” current.
4.11
Standby Current (IDDS)
The average amount of current required while no conversion is occurring and while no data is being output
(i.e., SCL and SDA lines are quiet).
4.12
I2C Standard Mode Timing
I2C specification where the frequency of SCL is
100 kHz.
4.13
I2C Fast Mode Timing
I2C specification where the frequency of SCL is
400 kHz.
DS21732C-page 14
© 2006 Microchip Technology Inc.
MCP3221
5.0
SERIAL COMMUNICATIONS
5.1
I2C Bus Characteristics
The following bus protocol has been defined:
• Data transfer may be initiated only when the bus
is not busy.
• During data transfer, the data line must remain
stable whenever the clock line is high. Changes in
the data line while the clock line is high will be
interpreted as a START or STOP condition.
Accordingly, the following bus conditions have been
defined (refer to Figure 5-1).
5.1.1
BUS NOT BUSY (A)
Both data and clock lines remain high.
5.1.2
START DATA TRANSFER (B)
A high-to-low transition of the SDA line while the clock
(SCL) is high determines a START condition. All
commands must be preceded by a START condition.
5.1.3
STOP DATA TRANSFER (C)
A low-to-high transition of the SDA line while the clock
(SCL) is high determines a STOP condition. All
operations must be ended with a STOP condition.
5.1.4
DATA VALID (D)
The state of the data line represents valid data when,
after a START condition, the data line is stable for the
duration of the clock signal’s high period.
The data on the line must be changed during the low
period of the clock signal. There is one clock pulse per
bit of data.
SCL
(A)
(B)
Each data transfer is initiated with a START condition
and terminated with a STOP condition. The number of
data bytes transferred between the START and STOP
conditions is determined by the master device and is
unlimited.
5.1.5
ACKNOWLEDGE
Each receiving device, when addressed, is obliged to
generate an acknowledge bit after the reception of
each byte. The master device must generate an extra
clock pulse which is associated with this acknowledge
bit.
The device that acknowledges has to pull down the
SDA line during the acknowledge clock pulse in such a
way that the SDA line is stable-low during the high
period of the acknowledge-related clock pulse. Setup
and hold times must be taken into account. During
reads, a master device must signal an end of data to
the slave by not generating an acknowledge bit on the
last byte that has been clocked out of the slave (NAK).
In this case, the slave (MCP3221) will release the bus
to allow the master device to generate the STOP
condition.
The MCP3221 supports a bidirectional, 2-wire bus and
data transmission protocol. The device that sends data
onto the bus is the transmitter and the device receiving
data is the receiver. The bus has to be controlled by a
master device which generates the serial clock (SCL),
controls the bus access and generates the START and
STOP conditions, while the MCP3221 works as a slave
device. Both master and slave devices can operate as
either transmitter or receiver, but the master device
determines which mode is activated.
(D)
(D)
(C)
(A)
SDA
START
CONDITION
FIGURE 5-1:
DATA
ADDRESS OR
ACKNOWLEDGE ALLOWED
TO CHANGE
VALID
STOP
CONDITION
Data Transfer Sequence on the Serial Bus.
© 2006 Microchip Technology Inc.
DS21732C-page 15
MCP3221
Device Addressing
5.3
The address byte is the first byte received following the
START condition from the master device. The first part
of the control byte consists of a 4-bit device code, which
is set to 1001 for the MCP3221. The device code is followed by three address bits: A2, A1 and A0. The default
address bits are 101. Contact the Microchip factory for
additional address bit options. The address bits allow
up to eight MCP3221 devices on the same bus and are
used to determine which device is accessed.
The eighth bit of the slave address determines if the
master device wants to read conversion data or write to
the MCP3221. When set to a ‘1’, a read operation is
selected. When set to a ‘0’, a write operation is
selected. There are no writable registers on the
MCP3221. Therefore, this bit must be set to a ’1’ in
order to initiate a conversion.
The MCP3221 is a slave device that is compatible with
the I2C 2-wire serial interface protocol. A hardware
connection diagram is shown in Figure 6-2. Communication is initiated by the microcontroller (master
device), which sends a START bit followed by the
address byte.
On completion of the conversion(s) performed by the
MCP3221, the microcontroller must send a STOP bit to
end communication.
The last bit in the device address byte is the R/W bit.
When this bit is a logic ‘1’, a conversion will be executed. Setting this bit to logic ‘0’ will also result in an
“acknowledge” (ACK) from the MCP3221, with the
device then releasing the bus. This can be used for
device polling. Refer to Section 6.3 “Device Polling”,
“Device Polling”, for more information.
START
Executing a Conversion
This section will describe the details of communicating
with the MCP3221 device. Initiating the sample-andhold acquisition, reading the conversion data and
executing multiple conversions will be discussed.
5.3.1
INITIATING THE SAMPLE AND
HOLD
The acquisition and conversion of the input signal
begins with the falling edge of the R/W bit of the
address byte. At this point, the internal clock initiates
the sample, hold and conversion cycle, all of which are
internal to the ADC.
tACQ + tCONV is
initiated here
Address Byte
SCL
1
2
3
4
SDA
1
0
0
1 A2 A1 A0 R/W
Start
Bit
FIGURE 5-3:
Address Byte.
Device bits
5
6
7
8
9
ACK
5.2
Address bits
Initiating the Conversion,
tACQ + tCONV is
initiated here
READ/WRITE
Lower Data Byte (n)
R/W A
SLAVE ADDRESS
17 18 19 20 21 22 23 24 25 26
0
1
0
Device Code
1
0
1
Address Bits(1)
Note 1: Contact Microchip for additional address bits.
FIGURE 5-2:
DS21732C-page 16
SDA
D8
D7 D6 D5 D4 D3 D2 D2 D0
ACK
1
ACK
SCL
FIGURE 5-4:
Initiating the Conversion,
Continuous Conversions.
Device Addressing.
© 2006 Microchip Technology Inc.
MCP3221
5.3.2
The input signal will initially be sampled with the first
falling edge of the clock following the transmission of a
logic-high R/W bit. Additionally, with the rising edge of
the SCL, the ADC will transmit an acknowledge bit
(ACK = 0). The master must release the data bus during this clock pulse to allow the MCP3221 to pull the
line low (refer to Figure 5-3).
READING THE CONVERSION DATA
Once the MCP3221 acknowledges the address byte,
the device will transmit four ‘0’ bits followed by the upper
four data bits of the conversion. The master device will
then acknowledge this byte with an ACK = Low. With the
following 8 clock pulses, the MCP3221 will transmit the
lower eight data bits from the conversion. The master
then sends an ACK = high, indicating to the MCP3221
that no more data is requested. The master can then
send a stop bit to end the transmission.
For consecutive samples, sampling begins on the falling edge of the LSB of the conversion result, which is
two bytes long. Refer to Figure 5-6 a for timing diagram.
tACQ + tCONV is
initiated here
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27
SCL
S
T
A
R
T
1
S
SDA
0
0
FIGURE 5-5:
A
2
1
Device bits
5.3.3
Upper Data Byte
Address Byte
A
1
A
C
K
R
/
W
A
0
0
0
0
0
D D D
11 10 9
S
T
O
P
Lower Data Byte
A
C D
K 7
D
8
D
6
D
5
D
4
D
3
D
2
D
1
N
A
K
D
0
P
Address bits
Executing a Conversion.
CONSECUTIVE CONVERSIONS
For consecutive samples, sampling begins on the falling edge of the LSB of the conversion result. See
Figure 5-6 for timing.
tACQ + tCONV is
initiated here
tACQ + tCONV is
initiated here
fSAMP = 22.3 ksps (fCLK = 400 kHz)
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
SCL
S
T
A
R
T
SDA
S
1
0
0
1 A2 A1 A0
Device bits
FIGURE 5-6:
Upper Data Byte (n)
Address Byte
R
/
W
A
C
K
0
0
0
0
D D D
11 10 9
Lower Data Byte (n)
D
8
A
C
K
D
7
D
6
D
5
D
4
D
3
D
2
D
1
D
0
A
C
K
0
Address bits
Continuous Conversion.
© 2006 Microchip Technology Inc.
DS21732C-page 17
MCP3221
6.0
APPLICATIONS INFORMATION
6.1
Driving the Analog Input
The MCP3221 has a single-ended analog input (AIN).
For proper conversion results, the voltage at the AIN
pin must be kept between VSS and VDD. If the converter
has no offset error, gain error, INL or DNL errors, and
the voltage level of AIN is equal to or less than
VSS + 1/2 LSB, the resultant code will be 000h. Additionally, if the voltage at AIN is equal to or greater than
VDD - 1.5 LSB, the output code will be FFFh.
The analog input model is shown in Figure 6-1. In this
diagram, the source impedance (RSS) adds to the internal sampling switch (RS) impedance, directly affecting
the time required to charge the capacitor (CSAMPLE).
Consequently, a larger source impedance increases
the offset error, gain error and integral linearity errors of
the conversion. Ideally, the impedance of the signal
source should be near zero. This is achievable with an
operational amplifier, such as the MCP6022, which has
a closed-loop output impedance of tens of ohms.
VDD
RSS
Sampling
Switch
VT = 0.6V
AIN
CPIN
7 pF
VA
VT = 0.6V
SS
RS = 1 kΩ
CSAMPLE
= DAC capacitance
= 20 pF
ILEAKAGE
±1 nA
VSS
Legend
VA
RSS
AIN
CPIN
VT
ILEAKAGE
SS
RS
CSAMPLE
=
=
=
=
=
=
=
=
=
FIGURE 6-1:
6.2
signal source
source impedance
analog input pad
analog input pin capacitance
threshold voltage
leakage current at the pin
due to various junctions
sampling switch
sampling switch resistor
sample/hold capacitance
Analog Input Model, AIN.
Connecting to the I2C Bus
The I2C bus is an open-collector bus, requiring pull-up
resistors connected to the SDA and SCL lines. This
configuration is shown in Figure 6-2.
The number of devices connected to the bus is limited
only by the maximum bus capacitance of 400 pF. A
possible configuration using multiple devices is shown
in Figure 6-3.
SDA SCL
VDD
PICmicro®
Microcontroller
PIC16F876
Microcontroller
RPU
RPU MCP3221
SDA
AIN
SCL
24LC01
EEPROM
Analog
Input
Signal
MCP3221
12-bit ADC
TC74
Temperature
Sensor
RPU is typically: 10 kΩ for fSCL = 100 kHz
2 kΩ for fSCL = 400 kHz
FIGURE 6-2:
Bus.
DS21732C-page 18
Pull-up Resistors on I2C
FIGURE 6-3:
Bus.
Multiple Devices on I2C™
© 2006 Microchip Technology Inc.
MCP3221
6.3
Device Polling
In some instances, it may be necessary to test for
MCP3221 presence on the I2C bus without performing
a conversion. This operation is described in Figure 6-4.
Here we are setting the R/W bit in the address byte to
a zero. The MCP3221 will then acknowledge by pulling
SDA low during the ACK clock and then release the
bus back to the I2C master. A stop or repeated start bit
can then be issued from the master and I2C
communication can continue.
Address Byte
1 2 3 4 5 6 7 8 9
SDA
1 0 0
1
Use of an analog ground plane is recommended in
order to keep the ground potential the same for all
devices on the board. Providing VDD connections to
devices in a “star” configuration can also reduce noise
by eliminating current return paths and associated
errors (Figure 6-6). For more information on layout tips
when using the MCP3221 or other ADC devices, refer
to AN688, “Layout Tips for 12-Bit A/D Converter
Applications”.
ACK
SCL
Digital and analog traces should be separated as much
as possible on the board, with no traces running
underneath the device or the bypass capacitor. Extra
precautions should be taken to keep traces with highfrequency signals (such as clock lines) as far as
possible from analog traces.
A2 A1A0 0
Start
R/W
Bit Device bits Address bits
VDD
Connection
Start
Bit
MCP3221 response
FIGURE 6-4:
6.4
6.4.1
Device Power and Layout
Considerations
Device 3
POWERING THE MCP3221
VDD supplies the power to the device as well as the reference voltage. A bypass capacitor value of 0.1 µF is
recommended. Adding a 10 µF capacitor in parallel is
recommended to attenuate higher frequency noise
present in some systems.
VDD
0.1 µF
VDD
AIN
MCP3221
Device 2
FIGURE 6-6:
VDD traces arranged in a
‘Star’ configuration in order to reduce errors
caused by current return paths.
6.4.3
VDD
10 µF
Device 4
Device 1
Device Polling.
SCL
SDA
RPU RPU
To
Microcontroller
USING A REFERENCE FOR
SUPPLY
The MCP3221 uses VDD as both power and a reference. In some applications, it may be necessary to use
a stable reference to achieve the required accuracy.
Figure 6-7 shows an example using the MCP1541 as a
4.096V, 2% reference.
6.4.2
Powering the MCP3221.
LAYOUT CONSIDERATIONS
When laying out a printed circuit board for use with
analog components, care should be taken to reduce
noise wherever possible. A bypass capacitor from VDD
to ground should always be used with this device and
should be placed as close as possible to the device pin.
A bypass capacitor value of 0.1 µF is recommended.
© 2006 Microchip Technology Inc.
VDD
1 µF
MCP1541
CL
4.096V
Reference
AIN
VDD
SCL
MCP3221
SDA
RPU
To
Microcontroller
FIGURE 6-5:
0.1 µF
VDD
FIGURE 6-7:
Stable Power and
Reference Configuration.
DS21732C-page 19
MCP3221
7.0
PACKAGING INFORMATION
7.1
Package Marking Information
5-Pin SOT-23A (EIAJ SC-74) Device
3
2
1
cdef
4
Part Number
5
Address Option
SOT-23
MCP3221A0T-I/OT
000
EE
MCP3221A1T-I/OT
001
EH
MCP3221A2T-I/OT
010
EB
MCP3221A3T-I/OT
011
EC
MCP3221A4T-I/OT
100
ED
MCP3221A5T-I/OT
101
S1 *
MCP3221A6T-I/OT
110
EF
MCP3221A7T-I/OT
111
EG
MCP3221A0T-E/OT
000
GE
MCP3221A1T-E/OT
001
GH
MCP3221A2T-E/OT
010
GB
MCP3221A3T-E/OT
011
GC
MCP3221A4T-E/OT
100
GD
MCP3221A5T-E/OT
101
GA *
MCP3221A6T-E/OT
110
GF
MCP3221A7T-E/OT
111
GG
* Default option. Contact Microchip Factory for other
address options.
Legend:
Note:
*
1
2
3
4
Part Number code + temperature range
Part Number code + temperature range
Year and work week
Lot ID
In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line thus limiting the number of available characters
for customer specific information.
Standard device marking consists of Microchip part number, year code, week code, and traceability
code.
DS21732C-page 20
© 2006 Microchip Technology Inc.
MCP3221
5-Lead Plastic Small Outline Transistor (OT) (SOT23)
E
E1
p
B
p1
n
D
1
α
c
A
φ
L
β
A1
INCHES*
Units
Dimension Limits
A2
MIN
MILLIMETERS
NOM
MAX
MIN
NOM
Pitch
n
p
.038
0.95
Outside lead pitch (basic)
p1
.075
1.90
Number of Pins
Overall Height
5
MAX
5
A
.035
.046
.057
0.90
1.18
1.45
Molded Package Thickness
A2
.035
.043
.051
0.90
1.10
1.30
Standoff
A1
.000
.003
.006
0.00
0.08
0.15
Overall Width
E
.102
.110
.118
2.60
2.80
3.00
Molded Package Width
E1
.059
.064
.069
1.50
1.63
1.75
Overall Length
D
.110
.116
.122
2.80
2.95
3.10
Foot Length
.014
.018
.022
0.35
0.45
0.55
Foot Angle
L
f
Lead Thickness
c
.004
Lead Width
B
a
.014
Mold Draft Angle Top
Mold Draft Angle Bottom
b
0
5
.006
.017
10
0
5
.008
0.09
0.15
.020
0.35
0.43
10
0.20
0.50
0
5
10
0
5
10
0
5
10
0
5
10
* Controlling Parameter
Notes:
Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .005" (0.127mm) per side.
EIAJ Equivalent: SC-74A
Revised 09-12-05
Drawing No. C04-091
© 2006 Microchip Technology Inc.
DS21732C-page 21
MCP3221
NOTES:
DS21732C-page 22
© 2006 Microchip Technology Inc.
MCP3221
APPENDIX A:
REVISION HISTORY
Revision C (July 2006)
• Section 5.2 Device Address: Changed 4-bit
device code to “1001”. Changed three address
bits to “101”.
Revision B (May 2003)
• Numerous changes throughout document.
Revision A (November 2005)
• Original Release of this Document.
© 2006 Microchip Technology Inc.
DS21732C-page 23
MCP3221
NOTES:
DS21732C-page 24
© 2006 Microchip Technology Inc.
MCP3221
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PART NO.
XX
X
/XX
Device
Address
Options
Temperature
Range
Package
Device:
Temperature Range:
Address Options:
Package:
MCP3221T: 12-Bit 2-Wire Serial A/D Converter
(Tape and Reel)
I = -40°C to +85°C
E = -40°C to +125°C
XX
A2
A1
A0
A0
=
0
0
0
A1
=
0
0
1
A2
=
0
1
0
A3
=
0
1
1
A4
=
1
0
0
A5 *
=
1
0
1
A6
=
1
1
0
A7
=
1
1
1
Examples:
a)
MCP3221A0T-I/OT:
b)
MCP3221A1T-I/OT:
c)
MCP3221A2T-I/OT:
d)
MCP3221A3T-I/OT:
e)
MCP3221A4T-I/OT:
f)
MCP3221A5T-I/OT:
g)
MCP3221A6T-I/OT:
h)
MCP3221A7T-I/OT:
a)
MCP3221A0T-E/OT: Extended, A0 Address,
Tape and Reel
MCP3221A1T-E/OT: Extended, A1 Address,
Tape and Reel
MCP3221A2T-E/OT: Extended, A2 Address,
Tape and Reel
MCP3221A3T-E/OT: Extended, A3 Address,
Tape and Reel
MCP3221A4T-E/OT: Extended, A4 Address,
Tape and Reel
MCP3221A5T-E/OT: Extended, A5 Address,
Tape and Reel
MCP3221A6T-E/OT: Extended, A6 Address,
Tape and Reel
MCP3221A7T-IE/OT: Extended, A7 Address,
Tape and Reel
b)
c)
* Default option. Contact Microchip factory for other
address options
d)
OT = SOT-23, 5-lead (Tape and Reel)
e)
f)
g)
h)
© 2006 Microchip Technology Inc.
Industrial, A0 Address,
Tape and Reel
Industrial, A1 Address,
Tape and Reel
Industrial, A2 Address,
Tape and Reel
Industrial, A3 Address,
Tape and Reel
Industrial, A4 Address,
Tape and Reel
Industrial, A5 Address,
Tape and Reel
Industrial, A6 Address,
Tape and Reel
Industrial, A7 Address,
Tape and Reel
DS21732C-page 25
MCP3221
NOTES:
DS21732C-page 26
© 2006 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, Accuron,
dsPIC, KEELOQ, microID, MPLAB, PIC, PICmicro, PICSTART,
PRO MATE, PowerSmart, rfPIC, and SmartShunt are
registered trademarks of Microchip Technology Incorporated
in the U.S.A. and other countries.
AmpLab, FilterLab, Migratable Memory, MXDEV, MXLAB,
SEEVAL, SmartSensor and The Embedded Control Solutions
Company are registered trademarks of Microchip Technology
Incorporated in the U.S.A.
Analog-for-the-Digital Age, Application Maestro, CodeGuard,
dsPICDEM, dsPICDEM.net, dsPICworks, ECAN,
ECONOMONITOR, FanSense, FlexROM, fuzzyLAB,
In-Circuit Serial Programming, ICSP, ICEPIC, Linear Active
Thermistor, Mindi, MiWi, MPASM, MPLIB, MPLINK, PICkit,
PICDEM, PICDEM.net, PICLAB, PICtail, PowerCal,
PowerInfo, PowerMate, PowerTool, REAL ICE, rfLAB,
rfPICDEM, Select Mode, Smart Serial, SmartTel, Total
Endurance, UNI/O, WiperLock and ZENA are trademarks of
Microchip Technology Incorporated in the U.S.A. and other
countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
All other trademarks mentioned herein are property of their
respective companies.
© 2006, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
Printed on recycled paper.
Microchip received ISO/TS-16949:2002 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona, Gresham, Oregon and Mountain View, California. The
Company’s quality system processes and procedures are for its
PICmicro® 8-bit MCUs, KEELOQ® code hopping devices, Serial
EEPROMs, microperipherals, nonvolatile memory and analog
products. In addition, Microchip’s quality system for the design and
manufacture of development systems is ISO 9001:2000 certified.
© 2006 Microchip Technology Inc.
DS21732C-page 27
WORLDWIDE SALES AND SERVICE
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://support.microchip.com
Web Address:
www.microchip.com
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
India - Bangalore
Tel: 91-80-4182-8400
Fax: 91-80-4182-8422
China - Beijing
Tel: 86-10-8528-2100
Fax: 86-10-8528-2104
India - New Delhi
Tel: 91-11-5160-8631
Fax: 91-11-5160-8632
Austria - Wels
Tel: 43-7242-2244-3910
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
China - Chengdu
Tel: 86-28-8676-6200
Fax: 86-28-8676-6599
India - Pune
Tel: 91-20-2566-1512
Fax: 91-20-2566-1513
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
China - Fuzhou
Tel: 86-591-8750-3506
Fax: 86-591-8750-3521
Japan - Yokohama
Tel: 81-45-471- 6166
Fax: 81-45-471-6122
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
China - Hong Kong SAR
Tel: 852-2401-1200
Fax: 852-2401-3431
Korea - Gumi
Tel: 82-54-473-4301
Fax: 82-54-473-4302
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Habour City, Kowloon
Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
Atlanta
Alpharetta, GA
Tel: 770-640-0034
Fax: 770-640-0307
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Farmington Hills, MI
Tel: 248-538-2250
Fax: 248-538-2260
Kokomo
Kokomo, IN
Tel: 765-864-8360
Fax: 765-864-8387
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
China - Shenzhen
Tel: 86-755-8203-2660
Fax: 86-755-8203-1760
China - Shunde
Tel: 86-757-2839-5507
Fax: 86-757-2839-5571
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
China - Xian
Tel: 86-29-8833-7250
Fax: 86-29-8833-7256
Malaysia - Penang
Tel: 60-4-646-8870
Fax: 60-4-646-5086
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
UK - Wokingham
Tel: 44-118-921-5869
Fax: 44-118-921-5820
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
Taiwan - Hsin Chu
Tel: 886-3-572-9526
Fax: 886-3-572-6459
Taiwan - Kaohsiung
Tel: 886-7-536-4818
Fax: 886-7-536-4803
Taiwan - Taipei
Tel: 886-2-2500-6610
Fax: 886-2-2508-0102
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
San Jose
Mountain View, CA
Tel: 650-215-1444
Fax: 650-961-0286
Toronto
Mississauga, Ontario,
Canada
Tel: 905-673-0699
Fax: 905-673-6509
DS21732C-page 28
06/08/06
© 2006 Microchip Technology Inc.