MDT10P55B u Power-on Reset u Power edge-detector Reset This EPROM-Based 8-bit micro-controller uses a fully u Sleep Mode for power saving static CMOS technology process to achieve higher u 5 types of oscillator can be selected by 1. General Description speed and smaller size with the low power programming option: consump-tion and high noise immunity. On chip INTRC－Internal 4 MHz RC oscillator memory inclu-des 1K words of ROM, and 72 bytes of RC－Low cost RC oscillator static RAM. LFXT－Low frequency crystal oscillator XTAL－Standard crystal oscillator 2. Features HFXT－High frequency crystal oscillator u The followings are some of the features on the 3 oscillator start-up time can be selected by hardware and software : programming option: u Fully CMOS static design 20 ms, 40 ms, 80 ms u 8-bit data bus u On chip EPROM size : 1K words u Internal RAM size : 72 bytes u 36 single word instructions u 14-bit instructions u 2-level stacks u Operating voltage : 2.5 V ~ 5.5 V u Operating frequency : 0 ~ 20 MHz u The most fast execution time is 200 ns under The application areas of this MDT10P55B range 20 MHz in all single cycle instructions except from appliance motor control and high speed the branch instruction automotive to low power remote Addressing modes include direct, indirect and transmitters/receivers, small instruments, chargers, relative addressing modes toy, automobile and PC pe-ripheral … etc. u u 8-bit real time clock/counter(RTCC) with 8-bit programmable prescaler u On-chip RC oscillator based Watchdog Timer(WDT) u Wake-up from sleep on pin change 3. Applications This specification are subject to be changed without notice. Any latest information please preview http;//www.mdtic.com.tw P. 1 2005/6 Ver. 1.2 MDT10P55B 4. Pin Assignment MDT10P55B3P/MDT10P55B3S MDT10P55B1P/MDT10P55B1S VDD PB5 PB4 PB3 PC5/RTCC PC4 PC3 1 2 3 4 5 6 7 14 13 12 11 10 9 8 VDD PB5 PB4 /MCLR PC5/RTCC PC4 PC3 VSS PB0 PB1 PB2 PC0 PC1 PC2 1 2 3 4 5 6 7 14 12 12 11 10 9 8 14 13 12 11 10 9 8 VSS PB0 PB1 PB2 PC0 PC1 PC2 MDT10P55B4P/MDT10P55B4S MDT10P55B2P/MDT10P55B2S VDD OSC1 OSC2/PB4 PB3 PC5/RTCC PC4 PC3 1 2 3 4 5 6 7 VDD OSC1 OSC2/PB4 /MCLR PC5/RTCC PC4 PC3 VSS PB0 PB1 PB2 PC0 PC1 PC2 1 2 3 4 5 6 7 14 13 12 11 10 9 8 VSS PB0 PB1 PB2 PC0 PC1 PC2 5. Pin Function Description Pin Name I/O Function Description PB5~0 I/O Port B, TTL input level，PB3 input only. PC4~0 I/O Port C, TTL input level PC5/RTCC I/O Real Time Clock/Counter, Schmitt Trigger input levels /MCLR I Master Clear, Schmitt Trigger input levels OSC1 I Oscillator Input OSC2 O Oscillator Output Vdd Power supply Vss Ground This specification are subject to be changed without notice. Any latest information please preview http;//www.mdtic.com.tw P. 2 2005/6 Ver. 1.2 MDT10P55B 6. Memory Map (A) Register Map Address Description 00 Indirect Addressing Register 01 RTCC 02 PC 03 STATUS 04 MSR 06 Port B 07 Port C 08~1F 30~3F General purpose registers 50~5F 70~7F (1)IAR ( Indirect Address Register) : R0 (2) RTCC (Real Time Counter/Counter Register) : R1 (3) PC (Program Counter) : R2 Write PC, CALL --- always 0 JUMP --- from instruction word RTWI, RET --- from STACK A9 A8 A7~A0 Write PC, JUMP, CALL --- from STATUS b5 RTWI, RET --- from STACK Write PC --- from ALU JUMP, CALL --- from instruction word RTWI, RET --- from STACK This specification are subject to be changed without notice. Any latest information please preview http;//www.mdtic.com.tw P. 3 2005/6 Ver. 1.2 MDT10P55B (4) STATUS (Status register) : R3 Bit Symbol Function 0 C Carry bit 1 HC Half Carry bit 2 Z Zero bit 3 PF Power down bit 4 TF WDT Timer overflow Flag bit 5 PAGE ROM page select bit 6 —— Unimplemented 7 PCWUF Pin change wake up from sleep (5) MSR (Memory Bank Select Register) : R4 b7 b6 Read only “1” b5 b4 b3 b2 b1 BANK Select Indirect Addressing Mode (6) PORT B : R6 PB5~PB0, I/O Register ，PB3 input only. (7) PORT C: R7 PC5~PC0, I/O Register (8) TMR (Time Mode Register) Bit Symbol Function Prescaler Value 2—0 3 PS2—0 PSC RTCC rate WDT rate 0 0 0 1:2 1:1 0 0 1 1:4 1:2 0 1:8 1:4 0 1 1 1 : 16 1:8 1 0 0 1 : 32 1 : 16 1 0 1 1 : 64 1 : 32 1 1 0 1 : 128 1 : 64 1 : 256 1 : 128 1 0 1 1 1 Prescaler assignment bit : 0 — RTCC 1 — Watchdog Timer This specification are subject to be changed without notice. Any latest information please preview http;//www.mdtic.com.tw P. 4 2005/6 Ver. 1.2 b0 MDT10P55B Bit Symbol 4 TCE 5 TCS 6 PBPHB 7 PBWUB Function RTCC signal Edge : 0 — Increment on low-to-high transition on RTCC pin 1 — Increment on high-to-low transition on RTCC pin RTCC signal set : 0 — Internal instruction cycle clock 1 — Transition on RTCC pin PortB pull-high :(RB0,RB1,RB3,RB4) 0 — Enable 1 — Disable PortB wake-up : (RB0,RB1,RB3,RB4) 0 — Enable 1 — Disable (9) CPIO B ，CPIO C (Control Port I/O Mode Register) The CPIO register is “write-only” ＝“0”, I/O pin in output mode; ＝“1”, I/O pin in input mode. (10) Configurable options for EPROM (Set by writer) : Oscillator Type Oscillator Start-up Time INTRC Oscillator RC 20ms,40ms,80ms Oscillator 20ms,40ms,80ms HFXT Oscillator 20 ms,40ms,80ms XTAL Oscillator 20ms,40 ms,80ms LFXT Oscillator 20ms,40 ms,80 ms Watchdog Timer control Watchdog timer disable all the time Watchdog timer enable all the time Security state Security Disable Security Enable The default security state of EPROM is weak disable. Once the IC was set to enable or disable, it’s forbidden to change. This specification are subject to be changed without notice. Any latest information please preview http;//www.mdtic.com.tw P. 5 2005/6 Ver. 1.2 MDT10P55B (B) Program Memory Address Description 000-3FF Program memory 000 The starting address of power on, external reset or WDT time-out reset. 8. Reset Condition for all Registers Register Address Power-On Reset /MCLR Reset WDT Reset CPIO B －－ --11 1111 --111 1111 --11 1111 CPIO C －－ --11 1111 --11 1111 --11 1111 TMR －－ 1111 1111 1111 1111 --11 1111 IAR 00h xxxx xxxx uuuu uuuu uuuu uuuu RTCC 01h xxxx xxxx uuuu uuuu uuuu uuuu PC 02h 0000 0000 0000 0000 0000 0000 STATUS 03h 0001 1xxx #00# #uuu #00# #uuu MSR 04h 110x xxxx 11uu uuuu 11uu uuuu PORT B 06h --xx xxxx --uu uuuu --uu uuuu PORT C 07h --xx xxxx --uu uuuu --uu uuuu Note : u＝unchanged, x＝unknown, - ＝unimplemented, read as “0” #＝value depends on the condition of the following table Condition Status: bit 7 Status: bit 4 Status: bit 3 /MCLR reset (not during SLEEP) 0 u u /MCLR reset during SLEEP 0 1 0 WDT reset (not during SLEEP) 0 0 1 WDT reset during SLEEP 0 0 0 Wake-up from SLEEP on pin change 1 1 0 9. Instruction Set : Instruction Code Mnemonic Operands Function Operating Status 010000 00000000 NOP No operation None 010000 00000001 CLRWT Clear Watchdog timer 0→WT TF, PF 010000 00000010 SLEEP Sleep mode 0→WT, stop OSC TF, PF 010000 00000011 TMODE Load W to TMODE register W→TMODE None 010000 00000100 RET Return Stack→PC None This specification are subject to be changed without notice. Any latest information please preview http;//www.mdtic.com.tw P. 6 2005/6 Ver. 1.2 MDT10P55B Instruction Code Mnemonic Operands Function Operating Status 010000 00000rrr CPIO R Control I/O port register W→CPIO r None 010001 1rrrrrrr STWR R Store W to register W→R None 011000 trrrrrrr LDR R, t Load register R→t Z 111010 iiiiiiii LDWI I Load immediate to W I→W None 010111 trrrrrrr SWAPR R, t Swap halves register [R(0~3) ↔R(4~7)] →t None 011001 trrrrrrr INCR R, t Increment register R + 1→t Z 011010 trrrrrrr INCRSZ R, t Increment register, skip if zero R + 1→t None 011011 trrrrrrr ADDWR R, t Add W and register W + R→t C, HC, Z 011100 trrrrrrr SUBWR R, t Subtract W from register R ﹣W→t or (R+/W+1→t) C, HC, Z 011101 trrrrrrr DECR R, t Decrement register R ﹣1→t Z 011110 trrrrrrr DECRSZ R, t Decrement register, skip if zero R ﹣1→t None 010010 trrrrrrr ANDWR R, t AND W and register R ∩ W→t Z 110100 iiiiiiii ANDWI i AND W and immediate i ∩ W→W Z 010011 trrrrrrr IORWR R, t Inclu. OR W and register R ∪ W→t Z 110101 iiiiiiii IORWI i Inclu. OR W and immediate i ∪ W→W Z 010100 trrrrrrr XORWR R, t Exclu. OR W and register R ♁ W→t Z 110110 iiiiiiii XORWI i Exclu. OR W and immediate i ♁ W→W Z 011111 trrrrrrr COMR R, t Complement register /R→t Z 010110 trrrrrrr RRR Rotate right register R(n) →R(n-1), C R, t C→R(7), R(0)→C 010101 trrrrrrr RLR R, t Rotate left register R(n)→r(n+1), C C→R(0), R(7)→C 010000 1xxxxxxx CLRW Clear working register 0→W Z 010001 0rrrrrrr CLRR Clear register 0→R Z 0000bb brrrrrrr BCR R, b Bit clear 0→R(b) None 0010bb brrrrrrr BSR R, b Bit set 1→R(b) None 0001bb brrrrrrr BTSC R, b Bit Test, skip if clear Skip if R(b)=0 None 0011bb brrrrrrr BTSS R, b Bit Test, skip if set Skip if R(b)=1 None 1000nn nnnnnnnn LCALL n Long CALL subroutine n→PC, None R PC+1→Stack 1010nn nnnnnnnn LJUMP n Long JUMP to address n→PC None 110000 nnnnnnnn CALL Call subroutine n→PC, None n PC+1→Stack 110001 iiiiiiii RTWI 11001n nnnnnnnn JUMP i n Return, place immediate to W Stack→PC,i→W None JUMP to address n→PC None Note : This specification are subject to be changed without notice. Any latest information please preview http;//www.mdtic.com.tw P. 7 2005/6 Ver. 1.2 MDT10P55B W WT TMODE CPIO TF PF PC OSC Inclu. Exclu. AND : : : : : : : : : : : Working register Watchdog timer TMODE mode register Control I/O port register Timer overflow flag Power loss flag Program Counter Oscillator Inclusive ‘∪’ Exclusive ‘♁’ Logic AND ‘∩’ b t R C HC Z / x i n : : 0 1 : : : : : : : : Bit position Target : Working register : General register General register address Carry flag Half carry Zero flag Complement Don’t care Immediate data ( 8 bits ) Immediate address 10. Oscillator start up timer condition : Oscillator Type INTRC,RC HF,XT,LF Porwer-on reset Subsequest resets 20ms,40ms,80ms 300us 20ms,40ms,80ms 20ms,40ms,80ms 11. Electrical Characteristics *Note: Temperature=25°C 1.Operation Current : (1) HF (C=10p) , WDT - enable 4M 10M 20M Sleep 2.5V 250uA 600uA 1.2mA 3.0uA 3.0V 325uA 740uA 1.4mA 8uA 4.0V 400uA 820uA 1.8mA 16uA 5.0V 622uA 1mA 2mA 30uA 6.4V 1mA 1.6mA 2.9mA 42.5uA These parameters are for reference only. (2) XT (C=10p) , WDT - enable 1M 4M 10M Sleep 500uA 1.0uA 2.5V 100uA 280uA 3.0V 185uA 250uA 460uA 10uA 4.0V 280uA 340uA 700uA 15uA 5.0V 400uA 600uA 1mA 30uA 6.4V 900uA 980uA 1.6mA 60uA These parameters are for reference only. This specification are subject to be changed without notice. Any latest information please preview http;//www.mdtic.com.tw P. 8 2005/6 Ver. 1.2 MDT10P55B (3) RC , WDT – Enable , @Vdd = 5.0V C 3p 20p 100p 300p R Freq. Current 4.7k 8.2M 1mA 10k 4.2M 630uA 47k 968K 180uA 100k 464K 130uA 300k 156K 114uA 470k 100K 110uA 4.7k 4.9M 630uA 10k 2.5M 360uA 47k 540K 156uA 100k 260K 128uA 300k 84K 112uA 470k 56K 100uA 4.7k 1.76M 300uA 10k 860K 200uA 47k 190K 120uA 100k 90.8K 113uA 300k 30K 97uA 470k 18.8K 97uA 4.7k 776K 170uA 10k 376K 133uA 47k 82K 106uA 100k 39.2K 102uA 300k 12.8K 91uA 470k 8K 85uA These parameters are for reference only. (4) LF (C=10p) , WDT - disable 32K 455K 1M Sleep 2.5V 30uA X X 1.0uA 3.0V 60uA @3.2V,300uA @3.2V,300uA 1.0uA 4.0V 150uA 450uA 450uA 1.0uA 5.0V 300uA 750uA 750uA 1.0uA 6.4V 750uA 1.2mA 1.2mA 1.0uA These parameters are for reference only. This specification are subject to be changed without notice. Any latest information please preview http;//www.mdtic.com.tw P. 9 2005/6 Ver. 1.2 MDT10P55B 2. Input Voltage (Vdd = 5V) : Port Min Max TTL Vss 1.5V Schmitt trigger Vss 1.25V TTL 2V Vdd Schmitt trigger 3V Vdd Vil Vih These parameters are for reference only. 3. Output Voltage (Vdd = 5V) : PA,PB Condition Voh 3.8V Ioh =-20mA Vol 0.8V Iol =+20mA Voh 4.3V Ioh = -5mA Vol 0.6V Iol = +5mA These parameters are for reference only. 4. Output Current (Max.) (Vdd = 5V) : Port B: Current Source current 25mA Sink current 25mA These parameters are for reference only. Port C: Current Source current 25mA sink current 25mA These parameters are for reference only. 5. The basic WDT time-out cycle time : Time 2.5V 25ms 3.0V 23ms 4.0V 20ms 5.0V 19ms 6.3V 18ms These parameters are for reference only. This specification are subject to be changed without notice. Any latest information please preview http;//www.mdtic.com.tw P. 10 2005/6 Ver. 1.2 MDT10P55B 6. (1)INT_RC,WDT – disable IC1: 4M Sleep 3.0V 500uA 1.0uA 4.0V 800A 1.0uA 5.0V 1mA These parameters are for reference only. 1.0uA (2)INT_RC,WDT – enable IC1: 4M Sleep 3.0V 600uA 5uA 4.0V 1mA 15uA 5.0V 1.2mA These parameters are for reference only. 30uA 7. Min Operation Voltage : C => 10p 20p 30p XT, 20M 2.5V 2.7V 3V 2.7V 3V 10p 20p 3.2V 3.4V HF, 20M 2.5V These parameters are for reference only. RC, 1k, no cap. 2.2V These parameters are for reference only. C => 0p LF, 1M 2.8V These parameters are for reference only. 8. MCLR filter time : Vdd=5V time 1000ns These parameters are for reference only. This specification are subject to be changed without notice. Any latest information please preview http;//www.mdtic.com.tw P. 11 2005/6 Ver. 1.2