DC-DC 5-35 Watts xppower.com MTC Series • 10-50 VDC Input Range • Designed for Vetronic & Avionic Use • Single & Dual Output Versions • -55 °C Operation Available • EMI Performance to MIL-STD 461E/F • Input Immunity to MIL-STD 1275A/B/C/D • Environments to MIL-STD 810F Specification Input Input Voltage Range Transient Input Range Turn On Turn Off Input Reverse Voltage Protection Max Input Current General • 15.5-40.0 VDC • 10 VDC maximum load for 10 s, 50 VDC for 1 s at full load • <15.5 VDC • <10 VDC • None Efficiency Isolation Switching Frequency Frequency Synchronisation Inhibit • See table MTBF Output Output Voltage Output Voltage Trim Minimum Load Line Regulation Load Regulation Cross Regulation • • • • • • Output Set Tolerance Ripple & Noise • • Overvoltage Protection • See table See table (Not available for dual outputs) No minimum load required ±1% Vout nominal (15.5-40.0 Vin) ±1% Vout nominal ±3% with 150 mA min load (Dual output only) see longform datasheet for more information ±100 mV or ±2% whichever is greater ≤5 Vout: 60 mV pk-pk max, >5 Vout: 1% pk-pk, at max load & 20 MHz BW 110-120% Vout max (15 W & 30 W versions only) 105-150% at nominal input voltage 102 °C to 107 °C, 2 °C to 5 °C hysteresis 0.5 V (Single output only) <±3% of Vout nom (25-75% load) Overcurrent Protection Overtemperature Protection Remote Sense Load Step Output Transient Load Step Recovery Line Step Output Transient Line Step Recovery • • Start Up Time • <100 ms Maximum Capacitive Load • 300 µF x Iout max startup within 100 ms • • • 500 µs within 1% of nominal value • <±3% of nominal Vout (15.5-40.0 Vin) • 500 µs within 1% of nominal value • See tables and performance curves • 1500 VDC Input to Output, 1000 VDC Input to Case, 500 VDC Output to Case • Fixed 450 kHz typical • 400-500 kHz • Off = TTL Low or short circuit On = TTL High or open circuit • MTC05: 1.7 MHrs, MTC15: 890 kHrs MTC30: 740 kHrs, to MIL-HDBK-217F GF at +40 °C Environmental Case Temperature Operating Humidity Storage Temperature Operating Altitude Shock Vibration Bump Salt Atmosphere • -40 °C to +100 °C (extended range ‘-LT’: -55 °C to +100 °C) • 88% Relative Humidity 240h MIL-STD-810D Method 507.2 • -50 °C to + 125 °C • Tested to 70000 ft (21336 m) • 100 g MIL-STD-810D Method 516.3 • 10 to 2000 Hz MIL-STD-810D Method 514.3 • 2000 Bumps in each axis 40 g MIL-STD-810D Method 516.3 • 48 hours MIL-STD-810E Method 509.3 Environmental Screening & Low Temperature All standard products are stress-screened and electrically tested over the operating temperature range. See notes for option details. EMC Conducted Emissions Immunity Conducted Susceptibilty • EN55022 Conducted Level B* MIL-STD 461E/F CE102* DEF STAN 59-41: DCE01/DCE02* • MIL-STD-704 A*, MIL-STD-704 B-F MIL-STD-1275A/B/C/D* • MIL-STD-461E/F CS101 CS114,CS115,CS116* * MTF50 Filter Module recommended to meet these standards Output Power 4W 4W 5W 5W 5W Output Voltage Min(1) 3.3 VDC 4.0 VDC 9.0 VDC 11.0 VDC 20.0 VDC Nominal 3.3 VDC 5.0 VDC 12.0 VDC 15.0 VDC 28.0 VDC Max(1) 4.0 VDC 6.0 VDC (2) 13.8 VDC 17.0 VDC 30.0 VDC Input Current(5) No Load Full Load 0.03 A 0.18 A 0.02 A 0.19 A 0.02 A 0.23 A 0.01 A 0.23 A 0.02 A 0.22 A Output Current 1.21 A 0.80 A 0.42 A 0.33 A 0.18 A Efficiency 80% 77% 78% 77% 78% Model Number(3,4) MTC0528S3V3 MTC0528S05 MTC0528S12 MTC0528S15 MTC0528S28 Notes 1. Indicates maximum and minimum voltage adjustment (maximum includes Remote Sense adjustment). 2. The full trim range is not available when the input is <15.5 V. 3. For additional ESS screening, add the suffix ‘-ESS’ to the part number e.g. MTC0528S05-ESS. 4. For -55 ºC extended operating range option, add suffix ‘-LT’ to the part number e.g. MTC0528S05-LT. 5. Vin = 28 VDC. Mechanical Details Pin 12 Pin 1 0.1 (2.54) 0.5 (12.7) Bottom View Pin 7 Pin 6 0.130±0.008 (3.3±0.2) 0.760±0.012 (19.3±0.3) 1.260±0.012 (32.0±0.3) 0.343+0.020 -0.012 (8.7+0.5 -0.3 ) 0.130±0.008 (3.3±0.2) 1.0 (25.4) MTC05 Connections Function Case No Pin -Vin +Vin Synchronisation Inhibit No Pin Adjust +Sense +Vout -Vout No Pin Pin 1 2 3 4 5 6 7 8 9 10 11 12 Notes. 1. Dimensions are in inches (mm) 2. Tolerance: ±0.02 inches (±0.5 mm) 3. Weight: 0.02 lb (10 g) 4. Materials & Finish: Pin Diameter: 0.032 (0.8) Material: Cu Zn30 2.5 µm Ni Finish: 0.2-0.5 µm AU (HV 170-200) Case Material: Aluminium (Al Mg Si 0.5) Finish: Chromated Nameplate - Non-conductive plastic 0.177(4.5) Accessories For more information contact sales office or visit www.xppower.com. • For thermal pad, order model number MTC05 PAD. • For spacers, order model number MTC05 1 mm SPACER or MTC05 4 mm SPACER. Efficiency Curves MTC0528S05 MTC0528S28 100 100 90 90 80 80 70 60 Vin = 15.5 V Vin = 28.0 V Vin = 40.0 V 50 40 Efficiency % Efficiency % 70 60 40 30 30 20 20 10 10 0 Vin = 15.5 V Vin = 28.0 V Vin = 40.0 V 50 0 20 40 60 Iout nom % 80 100 20 40 60 Iout nom % 80 100 DC-DC MTC05 Models and Ratings Output Power 10 W 12 W 15 W 15 W 15 W 15 W (5) 15 W (5) Nominal 3.3 VDC 5.0 VDC 12.0 VDC 15.0 VDC 28.0 VDC ±12 VDC ±15 VDC Output Voltage Min(1) 3.3 VDC 4.0 VDC 9.0 VDC 11.0 VDC 20.0 VDC Output Current 3.03 A 2.40 A 1.25 A 1.00 A 0.54 A ±1.0 A (5) ±0.8 A (5) Max(1) 4.0 VDC 6.0 VDC 13.8 VDC 17.0 VDC 30.0 VDC Input Current(4) No Load Full Load 0.04 A 0.46 A 0.05 A 0.53 A 0.04 A 0.67 A 0.05 A 0.67 A 0.03 A 0.69 A 0.03 A 0.68 A 0.03 A 0.68 A Model Number(2,3) MTC1528S3V3 MTC1528S05 MTC1528S12 MTC1528S15 MTC1528S28 MTC1528D12 MTC1528D15 Efficiency 77% 81% 80% 80% 78% 80% 80% Notes 1. Indicates maximum and minimum voltage adjustment (maximum includes Remote Sense adjustment). 2. For additional ESS screening, add the suffix ‘-ESS’ to the part number e.g. MTC1528S05-ESS. 3. For -55 ºC extended operating range option, add suffix ‘-LT’ to the part number e.g. MTC1528S05-LT. 4. Typical with Vin = 28 VDC. 5. Max power 15 W must not be exceeded. Mechanical Details 1 Bottom View 0.216±0.008 (5.4±0.2) 0.724 1.024±0.012 (18.4) (26.0±0.3) 8 7 0.150 (3.8) 1.276 (32.4) 0.138±0.008 (3.5±0.2) 1.3 (33.02) 1.575 ±0.012 (40.0 0.500+0.021 -0.012 +0.5 (12.7-0.3 ) Dual Output 0.382+0.020 -0.012 (9.7+0.5 -0.3 ) Single Output MTC15 Connections Single Output Dual Output No Pin No Pin Case Case No Pin No Pin - Vin - Vin Synchronisation Synchronisation + Vin + Vin Inhibit Inhibit No Pin No Pin No Pin No Pin No Pin -Vout + Sense No Pin - Vout COM Adjust No Pin + Vout + Vout Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 14 0.1 (2.54) Notes. 1. Dimensions are in inches (mm) 2. Tolerance: ±0.02 inches (±0.5 mm) 3. Weight: 0.04 lb (20 g) 4. Materials & Finish: Pin Diameter: 0.032 (0.8) Material: Cu Zn30 2.5 µm Ni Finish: 0.2-0.5 µm AU (HV 170-200) Mounting Hole - Diameter: 0.102 (2.6) Case Material: Aluminium (Al Mg Si 0.5) Finish: Chromated Nameplate Non-conductive plastic 0.177(4.5) ±0.3 ) Accessories For more information contact sales office or visit www.xppower.com. • For thermal pad, order model number MTC15 PAD. • For spacers, order model number MTC15 3 mm SPACER. Efficiency Curves MTC1528S05 90 90 80 80 70 70 60 50 40 50 40 30 20 20 10 10 0 0 60 Iout % Vin = 15.5 V Vin = 28.0 V Vin = 40.0 V 80 100 90 60 30 40 100 Efficiency % 100 20 MTC1528D15 MTC1528S28 100 Efficiency % Efficiency % DC-DC MTC15 Models and Ratings 80 70 60 50 20 40 60 Iout % Vin = 15.5 V Vin = 28.0 V Vin = 40.0 V 80 100 25/25% 50/50% 80/20% Iout % Vin = 15.5 V Vin = 28.0 V Vin = 40.0 V 20/80% Output Power 20 W 25 W 32 W 35 W 35 W 30 W (6) 30 W (6) Nominal 3.3 VDC 5.0 VDC 12.0 VDC 15.0 VDC 28.0 VDC ±12 VDC ±15 VDC Output Voltage Min(1) 3.3 VDC 4.0 VDC 9.0 VDC 11.0 VDC 20.0 VDC Output Current 6.06 A 5.00 A 2.70 A 2.33 A 1.25 A ±2.0 A (6) ±1.6 A (6) Max(1) 4.0 VDC 6.0 VDC 13.8 VDC (2) 17.0 VDC (2) 30.0 VDC Input Current(5) No Load Full Load 0.06 A 0.89 A 0.09 A 1.08 A 0.05 A 1.41 A 0.06 A 1.54 A 0.07 A 1.51 A 0.04 A 1.33 A 0.04 A 1.33 A Model Number(3,4) MTC3028S3V3 MTC3028S05 MTC3028S12 MTC3028S15 MTC3028S28 MTC3028D12 MTC3028D15 Efficiency 80% 83% 81% 81% 83% 81% 80% Notes 1. Indicates maximum and minimum voltage adjustment (Maximum includes Remote Sense adjustment). 2. The full trim range is not available when the input is <15.5 V. 3. For additional ESS screening, add the suffix ‘-ESS’ to the part number e.g. MTC3028S05-ESS. 4. For -55 ºC extended operating range option, add suffix ‘-LT’ to the part number e.g. MTC3028S05-LT. 5. Typical with Vin = 28 VDC. 6. Max power 30 W must not be exceeded. Mechanical Details 26 1 1.512 (38.4) Bottom View 0.1 (2.54) 1.811±0.012 (46.0±0.3) 0.154±0.008 (3.9±0.2) 14 13 0.150 (3.8) 1.984 (50.4) 0.500+0.020 -0.012 (12.7+0.5 -0.3 ) 0.142±0.008 (3.6±0.2) MTC30 Connections Single Output Dual Output No Pin No Pin Case Case No Pin No Pin - Vin - Vin No Pin No Pin + Vin + Vin No Pin No Pin Synchronisation Synchronisation No Pin No Pin Inhibit Inhibit No Pin No Pin Thermal Warning (TW) Thermal Warning (TW) Signal GND (SGND) No Pin No Pin No Pin No Pin No Pin No Pin No Pin Adjust No Pin + Sense No Pin + Vout + Vout + Vout + Vout - Vout COM - Vout COM No Pin - Vout No Pin - Vout - Sense No Pin No Pin No Pin Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 2.000 (50.8) Notes. 1. Dimensions are in inches (mm) 2. Tolerance: ±0.02 inches (±0.5 mm) 3. Weight: 0.15 lb (70 g) 4. Materials & Finish: Pin Diameter: 0.032 (0.8) Material: Cu Zn30 2.5 µm Ni Finish: 0.2-0.5 µm AU (HV 170-200) Mounting Hole - Diameter: 0.102 (2.6) I Case Material: Aluminium (Al Mg Si 0.5) Finish: Chromated Nameplate Non-conductive plastic 0.177(4.5) 2.283±0.012(58.0±0.3) Accessories For more information contact sales office or visit www.xppower.com. • For thermal pad, order model number MTC30 PAD. Efficiency Curves MTC3028D15 MTC3028S28 90 90 80 80 70 70 60 50 40 90 60 50 40 30 30 20 20 10 10 0 100 Efficiency % 100 Efficiency % Efficiency % MTC3028S05 100 80 70 60 50 0 20 40 60 Iout % Vin = 15.5 V Vin = 28.0 V Vin = 40.0 V 80 100 20 40 60 Iout % Vin = 15.5 V Vin = 28.0 V Vin = 40.0 V 80 100 25/25% 50/50% 80/20% 20/80% Iout % Vin = 15.5 V Vin = 28.0 V Vin = 40.0 V 25-Jun-08 DC-DC MTC30 Models and Ratings